Hyper-V netvsc PMD and VMBus
Subsystems (2)
v12 cover Hyper-V netvsc PMD and VMBus
Final version of the Hyper-V native bus (VMBus)
and network device (netvsc) drivers. This virtual device is used in Microsoft Hyper-V in Windows 10, Windows Server 2016 and Azure. Most of this code was extracted from FreeBSD and some of this is from earlier code donated by Brocade.
Only Linux is supported at present, but the code is split to allow future FreeBSD and Windows support.
This version works with upstream kernel (4.16) but in that mode only a single queue is supported. With additional patches that are pending for 5.0 kernel, multi-queue support works as well.
Device binding is best done via driverctl; this required some additional fixes to kernel and driverctl to work correctly. Linux kernel vmbus support needed to support sysfs driver_override and driverctl needed to handle non-PCI bus from udev.
https://gitlab.com/driverctl/driverctl/merge_requests/3
http://driverdev.linuxdriverproject.org/pipermail/driverdev-devel/2018-April/118889.html
v12
- rebase to 18.08 tip
- support copyless transmit of large packets
- support external mbuf for large receive
v11
- workaround bug in large packet transmit
v10
- resolve RSS setup
- add documentation about restart issue
- update documentation to refer to 4.17
- use same RSS key as MLX
v9
- fix places where still targeted at previous release
- add map entry for rte_uuid
- fix meson build dependencies
v8
- targeted for 18.08, move release notes
- use Ted's libuuid (not FreeBSD) because that is 3 clause BSD license versus 2 clause in FreeBSD
- minor checkpatch whitespace fixes
v7
- add EAL UUID functions from BSD to remove dependency on libuuid this means device can be enabled by default and eliminates build issues
- add support for latest NetVSP protocol (from hayaingz)
- add probe finish for compatability with 18.05
- rebase to 18.05-rc3
Stephen Hemminger (4):
eal: add rte_uuid support
bus/vmbus: add hyper-v virtual bus support
net/netvsc: add hyper-v netvsc network device
net/netvsc: add documentation
MAINTAINERS | 11 + config/common_base | 13 + config/common_linuxapp | 3 + doc/guides/nics/features/netvsc.ini | 23 + doc/guides/nics/index.rst | 1 + doc/guides/nics/netvsc.rst | 101 ++ doc/guides/rel_notes/known_issues.rst | 20 + doc/guides/rel_notes/release_18_08.rst | 6 + drivers/bus/Makefile | 1 + drivers/bus/meson.build | 2 +- drivers/bus/vmbus/Makefile | 36 + drivers/bus/vmbus/linux/Makefile | 3 + drivers/bus/vmbus/linux/vmbus_bus.c | 355 +++++ drivers/bus/vmbus/linux/vmbus_uio.c | 390 +++++ drivers/bus/vmbus/meson.build | 18 + drivers/bus/vmbus/private.h | 132 ++ drivers/bus/vmbus/rte_bus_vmbus.h | 396 +++++ drivers/bus/vmbus/rte_bus_vmbus_version.map | 28 + drivers/bus/vmbus/rte_vmbus_reg.h | 344 +++++ drivers/bus/vmbus/vmbus_bufring.c | 241 +++ drivers/bus/vmbus/vmbus_channel.c | 406 +++++ drivers/bus/vmbus/vmbus_common.c | 286 ++++ drivers/bus/vmbus/vmbus_common_uio.c | 232 +++ drivers/net/Makefile | 1 + drivers/net/meson.build | 1 + drivers/net/netvsc/Makefile | 23 + drivers/net/netvsc/hn_ethdev.c | 760 ++++++++++ drivers/net/netvsc/hn_logs.h | 36 + drivers/net/netvsc/hn_nvs.c | 546 +++++++ drivers/net/netvsc/hn_nvs.h | 229 +++ drivers/net/netvsc/hn_rndis.c | 1101 ++++++++++++++ drivers/net/netvsc/hn_rndis.h | 32 + drivers/net/netvsc/hn_rxtx.c | 1329 +++++++++++++++++ drivers/net/netvsc/hn_var.h | 153 ++ drivers/net/netvsc/meson.build | 7 + drivers/net/netvsc/ndis.h | 378 +++++ drivers/net/netvsc/rndis.h | 414 +++++ drivers/net/netvsc/rte_pmd_netvsc_version.map | 5 + lib/librte_eal/bsdapp/eal/Makefile | 1 + lib/librte_eal/common/Makefile | 2 +- lib/librte_eal/common/eal_common_uuid.c | 193 +++ lib/librte_eal/common/include/rte_uuid.h | 129 ++ lib/librte_eal/common/meson.build | 2 + lib/librte_eal/linuxapp/eal/Makefile | 1 + lib/librte_eal/rte_eal_version.map | 9 + mk/rte.app.mk | 2 + 46 files changed, 8400 insertions(+), 2 deletions(-) create mode 100644 doc/guides/nics/features/netvsc.ini create mode 100644 doc/guides/nics/netvsc.rst create mode 100644 drivers/bus/vmbus/Makefile create mode 100644 drivers/bus/vmbus/linux/Makefile create mode 100644 drivers/bus/vmbus/linux/vmbus_bus.c create mode 100644 drivers/bus/vmbus/linux/vmbus_uio.c create mode 100644 drivers/bus/vmbus/meson.build create mode 100644 drivers/bus/vmbus/private.h create mode 100644 drivers/bus/vmbus/rte_bus_vmbus.h create mode 100644 drivers/bus/vmbus/rte_bus_vmbus_version.map create mode 100644 drivers/bus/vmbus/rte_vmbus_reg.h create mode 100644 drivers/bus/vmbus/vmbus_bufring.c create mode 100644 drivers/bus/vmbus/vmbus_channel.c create mode 100644 drivers/bus/vmbus/vmbus_common.c create mode 100644 drivers/bus/vmbus/vmbus_common_uio.c create mode 100644 drivers/net/netvsc/Makefile create mode 100644 drivers/net/netvsc/hn_ethdev.c create mode 100644 drivers/net/netvsc/hn_logs.h create mode 100644 drivers/net/netvsc/hn_nvs.c create mode 100644 drivers/net/netvsc/hn_nvs.h create mode 100644 drivers/net/netvsc/hn_rndis.c create mode 100644 drivers/net/netvsc/hn_rndis.h create mode 100644 drivers/net/netvsc/hn_rxtx.c create mode 100644 drivers/net/netvsc/hn_var.h create mode 100644 drivers/net/netvsc/meson.build create mode 100644 drivers/net/netvsc/ndis.h create mode 100644 drivers/net/netvsc/rndis.h create mode 100644 drivers/net/netvsc/rte_pmd_netvsc_version.map create mode 100644 lib/librte_eal/common/eal_common_uuid.c create mode 100644 lib/librte_eal/common/include/rte_uuid.h
Signature · 1 line
2.18.0
PATCH v12 1/4 eal: add rte_uuid support
Since uuid functions may not be available everywhere, implement uuid functions in DPDK. These are based off the BSD licensed libuuid in util-link.
--- lib/librte_eal/bsdapp/eal/Makefile | 1 + lib/librte_eal/common/Makefile | 2 +- lib/librte_eal/common/eal_common_uuid.c | 193 +++++++++++++++++++++++ lib/librte_eal/common/include/rte_uuid.h | 129 +++++++++++++++ lib/librte_eal/common/meson.build | 2 + lib/librte_eal/linuxapp/eal/Makefile | 1 + lib/librte_eal/rte_eal_version.map | 9 ++ 7 files changed, 336 insertions(+), 1 deletion(-) create mode 100644 lib/librte_eal/common/eal_common_uuid.c create mode 100644 lib/librte_eal/common/include/rte_uuid.h
lib/librte_eal/bsdapp/eal/Makefile +1 -0
@@ -58,6 +58,7 @@ SRCS-$(CONFIG_RTE_EXEC_ENV_BSDAPP) += eal_common_options.c SRCS-$(CONFIG_RTE_EXEC_ENV_BSDAPP) += eal_common_thread.c SRCS-$(CONFIG_RTE_EXEC_ENV_BSDAPP) += eal_common_proc.c SRCS-$(CONFIG_RTE_EXEC_ENV_BSDAPP) += eal_common_fbarray.c +SRCS-$(CONFIG_RTE_EXEC_ENV_BSDAPP) += eal_common_uuid.c SRCS-$(CONFIG_RTE_EXEC_ENV_BSDAPP) += rte_malloc.c SRCS-$(CONFIG_RTE_EXEC_ENV_BSDAPP) += malloc_elem.c SRCS-$(CONFIG_RTE_EXEC_ENV_BSDAPP) += malloc_heap.c
lib/librte_eal/common/Makefile +1 -1
@@ -16,7 +16,7 @@ INC += rte_pci_dev_feature_defs.h rte_pci_dev_features.h INC += rte_malloc.h rte_keepalive.h rte_time.h INC += rte_service.h rte_service_component.h INC += rte_bitmap.h rte_vfio.h rte_hypervisor.h rte_test.h -INC += rte_reciprocal.h rte_fbarray.h +INC += rte_reciprocal.h rte_fbarray.h rte_uuid.h GENERIC_INC := rte_atomic.h rte_byteorder.h rte_cycles.h rte_prefetch.h GENERIC_INC += rte_spinlock.h rte_memcpy.h rte_cpuflags.h rte_rwlock.h
lib/librte_eal/common/eal_common_uuid.c new file +193 -0
193 lines not on this page · raw message
lib/librte_eal/common/include/rte_uuid.h new file +129 -0
129 lines not on this page · raw message
lib/librte_eal/common/meson.build +2 -0
@@ -25,6 +25,7 @@ common_sources = files( 'eal_common_tailqs.c', 'eal_common_thread.c', 'eal_common_timer.c', + 'eal_common_uuid.c', 'malloc_elem.c', 'malloc_heap.c', 'malloc_mp.c',
@@ -75,6 +76,7 @@ common_headers = files( 'include/rte_string_fns.h', 'include/rte_tailq.h', 'include/rte_time.h', + 'include/rte_uuid.h', 'include/rte_version.h') # special case install the generic headers, since they go in a subdir
lib/librte_eal/linuxapp/eal/Makefile +1 -0
@@ -66,6 +66,7 @@ SRCS-$(CONFIG_RTE_EXEC_ENV_LINUXAPP) += eal_common_options.c SRCS-$(CONFIG_RTE_EXEC_ENV_LINUXAPP) += eal_common_thread.c SRCS-$(CONFIG_RTE_EXEC_ENV_LINUXAPP) += eal_common_proc.c SRCS-$(CONFIG_RTE_EXEC_ENV_LINUXAPP) += eal_common_fbarray.c +SRCS-$(CONFIG_RTE_EXEC_ENV_LINUXAPP) += eal_common_uuid.c SRCS-$(CONFIG_RTE_EXEC_ENV_LINUXAPP) += rte_malloc.c SRCS-$(CONFIG_RTE_EXEC_ENV_LINUXAPP) += malloc_elem.c SRCS-$(CONFIG_RTE_EXEC_ENV_LINUXAPP) += malloc_heap.c
lib/librte_eal/rte_eal_version.map +9 -0
@@ -241,6 +241,15 @@ DPDK_18.05 { } DPDK_18.02; +DPDK_18.08 { + global: + + rte_uuid_compare; + rte_uuid_is_null; + rte_uuid_parse; + rte_uuid_unparse; +} DPDK_18.05; + EXPERIMENTAL { global:
Signature · 1 line
2.18.0
PATCH v12 2/4 bus/vmbus: add hyper-v virtual bus support
In reply to Stephen HemmingerThis patch adds support for an additional bus type Virtual Machine BUS (VMBUS) on Microsoft Hyper-V in Windows 10, Windows Server 2016 and Azure. Most of this code was extracted from FreeBSD and some of this is from earlier code donated by Brocade.
Only Linux is supported at present, but the code is split to allow future FreeBSD and Windows support.
The bus support relies on the uio_hv_generic driver from Linux kernel 4.16. Multiple queue support requires additional sysfs interfaces which is in kernel 5.0 (a.k.a 4.17).
--- MAINTAINERS | 3 + config/common_base | 5 + drivers/bus/Makefile | 1 + drivers/bus/meson.build | 2 +- drivers/bus/vmbus/Makefile | 36 ++ drivers/bus/vmbus/linux/Makefile | 3 + drivers/bus/vmbus/linux/vmbus_bus.c | 355 +++++++++++++++++ drivers/bus/vmbus/linux/vmbus_uio.c | 390 +++++++++++++++++++ drivers/bus/vmbus/meson.build | 18 + drivers/bus/vmbus/private.h | 132 +++++++ drivers/bus/vmbus/rte_bus_vmbus.h | 396 +++++++++++++++++++ drivers/bus/vmbus/rte_bus_vmbus_version.map | 28 ++ drivers/bus/vmbus/rte_vmbus_reg.h | 344 +++++++++++++++++ drivers/bus/vmbus/vmbus_bufring.c | 241 ++++++++++++ drivers/bus/vmbus/vmbus_channel.c | 406 ++++++++++++++++++++ drivers/bus/vmbus/vmbus_common.c | 286 ++++++++++++++ drivers/bus/vmbus/vmbus_common_uio.c | 232 +++++++++++ mk/rte.app.mk | 1 + 18 files changed, 2878 insertions(+), 1 deletion(-) create mode 100644 drivers/bus/vmbus/Makefile create mode 100644 drivers/bus/vmbus/linux/Makefile create mode 100644 drivers/bus/vmbus/linux/vmbus_bus.c create mode 100644 drivers/bus/vmbus/linux/vmbus_uio.c create mode 100644 drivers/bus/vmbus/meson.build create mode 100644 drivers/bus/vmbus/private.h create mode 100644 drivers/bus/vmbus/rte_bus_vmbus.h create mode 100644 drivers/bus/vmbus/rte_bus_vmbus_version.map create mode 100644 drivers/bus/vmbus/rte_vmbus_reg.h create mode 100644 drivers/bus/vmbus/vmbus_bufring.c create mode 100644 drivers/bus/vmbus/vmbus_channel.c create mode 100644 drivers/bus/vmbus/vmbus_common.c create mode 100644 drivers/bus/vmbus/vmbus_common_uio.c
MAINTAINERS +3 -0
@@ -427,6 +427,9 @@ F: drivers/bus/pci/ VDEV bus driver F: drivers/bus/vdev/ +VMBUS bus driver +M: Stephen Hemminger <[email protected]> +F: drivers/bus/vmbus/ Networking Drivers ------------------
config/common_base +5 -0
@@ -400,6 +400,11 @@ CONFIG_RTE_LIBRTE_PMD_FAILSAFE=y CONFIG_RTE_LIBRTE_MVPP2_PMD=n # +# Compile support for VMBus library +# +CONFIG_RTE_LIBRTE_VMBUS=n + + # Compile virtual device driver for NetVSC on Hyper-V/Azure # CONFIG_RTE_LIBRTE_VDEV_NETVSC_PMD=n
drivers/bus/Makefile +1 -0
@@ -10,5 +10,6 @@ endif DIRS-$(CONFIG_RTE_LIBRTE_IFPGA_BUS) += ifpga DIRS-$(CONFIG_RTE_LIBRTE_PCI_BUS) += pci DIRS-$(CONFIG_RTE_LIBRTE_VDEV_BUS) += vdev +DIRS-$(CONFIG_RTE_LIBRTE_VMBUS) += vmbus include $(RTE_SDK)/mk/rte.subdir.mk
drivers/bus/meson.build +1 -1
@@ -1,7 +1,7 @@ # SPDX-License-Identifier: BSD-3-Clause # Copyright(c) 2017 Intel Corporation -drivers = ['dpaa', 'fslmc', 'ifpga', 'pci', 'vdev'] +drivers = ['dpaa', 'fslmc', 'ifpga', 'pci', 'vdev', 'vmbus'] std_deps = ['eal'] config_flag_fmt = 'RTE_LIBRTE_@0@_BUS' driver_name_fmt = 'rte_bus_@0@'
drivers/bus/vmbus/Makefile new file +36 -0
@@ -0,0 +1,36 @@ +# SPDX-License-Identifier: BSD-3-Clause + +include $(RTE_SDK)/mk/rte.vars.mk + +LIB = librte_bus_vmbus.a +LIBABIVER := 1 +EXPORT_MAP := rte_bus_vmbus_version.map + +CFLAGS += -I$(SRCDIR) +CFLAGS += -O3 $(WERROR_FLAGS) +CFLAGS += -DALLOW_EXPERIMENTAL_API + +ifneq ($(CONFIG_RTE_EXEC_ENV_LINUXAPP),) +SYSTEM := linux +endif +ifneq ($(CONFIG_RTE_EXEC_ENV_BSDAPP),) +$(error "VMBUS not implemented for BSD yet") +endif + +CFLAGS += -I$(RTE_SDK)/drivers/bus/vmbus/$(SYSTEM) +CFLAGS += -I$(RTE_SDK)/lib/librte_eal/common +CFLAGS += -I$(RTE_SDK)/lib/librte_eal/$(SYSTEM)app/eal + +LDLIBS += -lrte_eal -lrte_mbuf -lrte_mempool -lrte_ring +LDLIBS += -lrte_ethdev -luuid + +include $(RTE_SDK)/drivers/bus/vmbus/$(SYSTEM)/Makefile +SRCS-$(CONFIG_RTE_LIBRTE_VMBUS) := $(addprefix $(SYSTEM)/,$(SRCS)) +SRCS-$(CONFIG_RTE_LIBRTE_VMBUS) += vmbus_common.c +SRCS-$(CONFIG_RTE_LIBRTE_VMBUS) += vmbus_channel.c vmbus_bufring.c +SRCS-$(CONFIG_RTE_LIBRTE_VMBUS) += vmbus_common_uio.c + +SYMLINK-$(CONFIG_RTE_LIBRTE_VMBUS)-include += rte_bus_vmbus.h +SYMLINK-$(CONFIG_RTE_LIBRTE_VMBUS)-include += rte_vmbus_reg.h + +include $(RTE_SDK)/mk/rte.lib.mk
drivers/bus/vmbus/linux/Makefile new file +3 -0
@@ -0,0 +1,3 @@ +# SPDX-License-Identifier: BSD-3-Clause + +SRCS += vmbus_bus.c vmbus_uio.c
drivers/bus/vmbus/linux/vmbus_bus.c new file +355 -0
355 lines not on this page · raw message
drivers/bus/vmbus/linux/vmbus_uio.c new file +390 -0
390 lines not on this page · raw message
drivers/bus/vmbus/meson.build new file +18 -0
@@ -0,0 +1,18 @@ +# SPDX-License-Identifier: BSD-3-Clause + +allow_experimental_apis = true + +install_headers('rte_bus_vmbus.h','rte_vmbus_reg.h') + +sources = files('vmbus_common.c', + 'vmbus_channel.c', + 'vmbus_bufring.c', + 'vmbus_common_uio.c') + +if host_machine.system() == 'linux' + sources += files('linux/vmbus_bus.c', + 'linux/vmbus_uio.c') + includes += include_directories('linux') +else + build = false +endif
drivers/bus/vmbus/private.h new file +132 -0
132 lines not on this page · raw message
drivers/bus/vmbus/rte_bus_vmbus.h new file +396 -0
396 lines not on this page · raw message
drivers/bus/vmbus/rte_bus_vmbus_version.map new file +28 -0
@@ -0,0 +1,28 @@ +/* SPDX-License-Identifier: BSD-3-Clause */ +DPDK_18.08 { + global: + + rte_vmbus_chan_close; + rte_vmbus_chan_open; + rte_vmbus_chan_recv; + rte_vmbus_chan_recv_raw; + rte_vmbus_chan_rx_empty; + rte_vmbus_chan_send; + rte_vmbus_chan_send_sglist; + rte_vmbus_chan_signal_tx; + rte_vmbus_irq_mask; + rte_vmbus_irq_read; + rte_vmbus_irq_unmask; + rte_vmbus_map_device; + rte_vmbus_max_channels; + rte_vmbus_probe; + rte_vmbus_probe_one; + rte_vmbus_register; + rte_vmbus_scan; + rte_vmbus_sub_channel_index; + rte_vmbus_subchan_open; + rte_vmbus_unmap_device; + rte_vmbus_unregister; + + local: *; +};
drivers/bus/vmbus/rte_vmbus_reg.h new file +344 -0
344 lines not on this page · raw message
drivers/bus/vmbus/vmbus_bufring.c new file +241 -0
241 lines not on this page · raw message
drivers/bus/vmbus/vmbus_channel.c new file +406 -0
406 lines not on this page · raw message
drivers/bus/vmbus/vmbus_common.c new file +286 -0
286 lines not on this page · raw message
drivers/bus/vmbus/vmbus_common_uio.c new file +232 -0
232 lines not on this page · raw message
mk/rte.app.mk +1 -0
@@ -175,6 +175,7 @@ _LDLIBS-$(CONFIG_RTE_LIBRTE_IFC_PMD) += -lrte_pmd_ifc endif # $(CONFIG_RTE_EAL_VFIO) endif # $(CONFIG_RTE_LIBRTE_VHOST) _LDLIBS-$(CONFIG_RTE_LIBRTE_VMXNET3_PMD) += -lrte_pmd_vmxnet3_uio +_LDLIBS-$(CONFIG_RTE_LIBRTE_VMBUS) += -lrte_bus_vmbus ifeq ($(CONFIG_RTE_LIBRTE_BBDEV),y) _LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_BBDEV_NULL) += -lrte_pmd_bbdev_null
Signature · 1 line
2.18.0
PATCH v12 3/4 net/netvsc: add hyper-v netvsc network device
In reply to Stephen HemmingerThe driver supports Hyper-V networking directly like virtio for KVM or vmxnet3 for VMware.
This code is based off of the FreeBSD driver. The file and variable names are kept the same to help with understanding (with most of the BSD style warts removed).
This version supports the latest NetVSP 6.1 version and older versions.
--- MAINTAINERS | 8 + config/common_base | 8 + config/common_linuxapp | 3 + drivers/net/Makefile | 1 + drivers/net/meson.build | 1 + drivers/net/netvsc/Makefile | 23 + drivers/net/netvsc/hn_ethdev.c | 760 ++++++++++ drivers/net/netvsc/hn_logs.h | 36 + drivers/net/netvsc/hn_nvs.c | 546 +++++++ drivers/net/netvsc/hn_nvs.h | 229 +++ drivers/net/netvsc/hn_rndis.c | 1101 ++++++++++++++ drivers/net/netvsc/hn_rndis.h | 32 + drivers/net/netvsc/hn_rxtx.c | 1329 +++++++++++++++++ drivers/net/netvsc/hn_var.h | 153 ++ drivers/net/netvsc/meson.build | 7 + drivers/net/netvsc/ndis.h | 378 +++++ drivers/net/netvsc/rndis.h | 414 +++++ drivers/net/netvsc/rte_pmd_netvsc_version.map | 5 + mk/rte.app.mk | 1 + 19 files changed, 5035 insertions(+) create mode 100644 drivers/net/netvsc/Makefile create mode 100644 drivers/net/netvsc/hn_ethdev.c create mode 100644 drivers/net/netvsc/hn_logs.h create mode 100644 drivers/net/netvsc/hn_nvs.c create mode 100644 drivers/net/netvsc/hn_nvs.h create mode 100644 drivers/net/netvsc/hn_rndis.c create mode 100644 drivers/net/netvsc/hn_rndis.h create mode 100644 drivers/net/netvsc/hn_rxtx.c create mode 100644 drivers/net/netvsc/hn_var.h create mode 100644 drivers/net/netvsc/meson.build create mode 100644 drivers/net/netvsc/ndis.h create mode 100644 drivers/net/netvsc/rndis.h create mode 100644 drivers/net/netvsc/rte_pmd_netvsc_version.map
MAINTAINERS +8 -0
@@ -606,6 +606,14 @@ F: drivers/net/vdev_netvsc/ F: doc/guides/nics/vdev_netvsc.rst F: doc/guides/nics/features/vdev_netvsc.ini +Microsoft Hyper-V netvsc - EXPERIMENTAL +M: Stephen Hemminger <[email protected]> +M: "K. Y. Srinivasan" <[email protected]> +M: Haiyang Zhang <[email protected]> +F: drivers/net/hyperv/ +F: doc/guides/nics/netvsc.rst +F: doc/guides/nics/features/netvsc.ini + Netcope szedata2 M: Matej Vido <[email protected]> F: drivers/net/szedata2/
config/common_base +8 -0
@@ -404,7 +404,15 @@ CONFIG_RTE_LIBRTE_MVPP2_PMD=n # CONFIG_RTE_LIBRTE_VMBUS=n +# +# Compile native PMD for Hyper-V/Azure +# +CONFIG_RTE_LIBRTE_NETVSC_PMD=n +CONFIG_RTE_LIBRTE_NETVSC_DEBUG_RX=n +CONFIG_RTE_LIBRTE_NETVSC_DEBUG_TX=n +CONFIG_RTE_LIBRTE_NETVSC_DEBUG_DUMP=n +# # Compile virtual device driver for NetVSC on Hyper-V/Azure # CONFIG_RTE_LIBRTE_VDEV_NETVSC_PMD=n
config/common_linuxapp +3 -0
@@ -26,6 +26,9 @@ CONFIG_RTE_LIBRTE_POWER=y CONFIG_RTE_VIRTIO_USER=y CONFIG_RTE_PROC_INFO=y +CONFIG_RTE_LIBRTE_VMBUS=y +CONFIG_RTE_LIBRTE_NETVSC_PMD=y + # NXP DPAA BUS and drivers CONFIG_RTE_LIBRTE_DPAA_BUS=y CONFIG_RTE_LIBRTE_DPAA_MEMPOOL=y
drivers/net/Makefile +1 -0
@@ -33,6 +33,7 @@ DIRS-$(CONFIG_RTE_LIBRTE_LIO_PMD) += liquidio DIRS-$(CONFIG_RTE_LIBRTE_MLX4_PMD) += mlx4 DIRS-$(CONFIG_RTE_LIBRTE_MLX5_PMD) += mlx5 DIRS-$(CONFIG_RTE_LIBRTE_MVPP2_PMD) += mvpp2 +DIRS-$(CONFIG_RTE_LIBRTE_NETVSC_PMD) += netvsc DIRS-$(CONFIG_RTE_LIBRTE_NFP_PMD) += nfp DIRS-$(CONFIG_RTE_LIBRTE_BNXT_PMD) += bnxt DIRS-$(CONFIG_RTE_LIBRTE_PMD_NULL) += null
drivers/net/meson.build +1 -0
@@ -19,6 +19,7 @@ drivers = ['af_packet', 'kni', 'liquidio', 'mvpp2', + 'netvsc', 'nfp', 'null', 'octeontx', 'pcap', 'ring', 'sfc',
drivers/net/netvsc/Makefile new file +23 -0
@@ -0,0 +1,23 @@ +# SPDX-License-Identifier: BSD-3-Clause + +include $(RTE_SDK)/mk/rte.vars.mk + +LIB = librte_pmd_netvsc.a + +CFLAGS += -O3 $(WERROR_FLAGS) +CFLAGS += -DALLOW_EXPERIMENTAL_API + +EXPORT_MAP := rte_pmd_netvsc_version.map + +LIBABIVER := 1 + +SRCS-$(CONFIG_RTE_LIBRTE_NETVSC_PMD) += hn_ethdev.c +SRCS-$(CONFIG_RTE_LIBRTE_NETVSC_PMD) += hn_rxtx.c +SRCS-$(CONFIG_RTE_LIBRTE_NETVSC_PMD) += hn_rndis.c +SRCS-$(CONFIG_RTE_LIBRTE_NETVSC_PMD) += hn_nvs.c + +LDLIBS += -lrte_eal -lrte_mbuf -lrte_mempool -lrte_ring +LDLIBS += -lrte_ethdev -lrte_net -lrte_kvargs +LDLIBS += -lrte_bus_vmbus + +include $(RTE_SDK)/mk/rte.lib.mk
drivers/net/netvsc/hn_ethdev.c new file +760 -0
760 lines not on this page · raw message
drivers/net/netvsc/hn_logs.h new file +36 -0
@@ -0,0 +1,36 @@ +/* SPDX-License-Identifier: BSD-3-Clause */ + +#ifndef _HN_LOGS_H_ +#define _HN_LOGS_H_ + +#include <rte_log.h> + +extern int hn_logtype_init; +extern int hn_logtype_driver; + +#define PMD_INIT_LOG(level, fmt, args...) \ + rte_log(RTE_LOG_ ## level, hn_logtype_init, "%s(): " fmt "\n",\ + __func__, ## args) +#define PMD_INIT_FUNC_TRACE () PMD_INIT_LOG(DEBUG, " >>") + +#ifdef RTE_LIBRTE_NETVSC_DEBUG_RX +#define PMD_RX_LOG(level, fmt, args...) \ + rte_log(RTE_LOG_ ## level, hn_logtype_driver, \ + "%s() rx: " fmt "\n", __func__, ## args) +#else +#define PMD_RX_LOG(level, fmt, args...) do { } while (0) +#endif + +#ifdef RTE_LIBRTE_NETVSC_DEBUG_TX +#define PMD_TX_LOG(level, fmt, args...) \ + rte_log(RTE_LOG_ ## level, hn_logtype_driver, \ + "%s() tx: " fmt "\n", __func__, ## args) +#else +#define PMD_TX_LOG(level, fmt, args...) do { } while (0) +#endif + +#define PMD_DRV_LOG(level, fmt, args...) \ + rte_log(RTE_LOG_ ## level, hn_logtype_driver, "%s(): " fmt "\n", \ + __func__, ## args) + +#endif /* _HN_LOGS_H_ */
drivers/net/netvsc/hn_nvs.c new file +546 -0
546 lines not on this page · raw message
drivers/net/netvsc/hn_nvs.h new file +229 -0
229 lines not on this page · raw message
drivers/net/netvsc/hn_rndis.c new file +1101 -0
1,101 lines not on this page · raw message
drivers/net/netvsc/hn_rndis.h new file +32 -0
@@ -0,0 +1,32 @@ +/* SPDX-License-Identifier: BSD-3-Clause */ + +#include "rndis.h" + +struct hn_data ; + +void hn_rndis_receive_response (struct hn_data *hv, +const void *data,uint32_t len); +void hn_rndis_link_status (struct hn_data *hv,const void *data); +int hn_rndis_attach (struct hn_data *hv); +void hn_rndis_detach (struct hn_data *hv); +int hn_rndis_get_eaddr (struct hn_data *hv,uint8_t *eaddr); +int hn_rndis_get_linkstatus (struct hn_data *hv); +int hn_rndis_get_linkspeed (struct hn_data *hv); +int hn_rndis_set_rxfilter (struct hn_data *hv,uint32_t filter); +void hn_rndis_rx_ctrl (struct hn_data *hv,const void *data, +int dlen); +int hn_rndis_get_offload (struct hn_data *hv, +struct rte_eth_dev_info *dev_info); +int hn_rndis_conf_offload (struct hn_data *hv, +uint64_t tx_offloads, +uint64_t rx_offloads); +int hn_rndis_query_rsscaps (struct hn_data *hv, +unsigned int *rxr_cnt0); +int hn_rndis_conf_rss (struct hn_data *hv, +const struct rte_eth_rss_conf *rss_conf); + +#ifdef RTE_LIBRTE_NETVSC_DEBUG_DUMP +void hn_rndis_dump (const void *buf); +#else +#define hn_rndis_dump (buf) +#endif
drivers/net/netvsc/hn_rxtx.c new file +1329 -0
221 lines not on this page · raw message
drivers/net/netvsc/hn_var.h new file +153 -0
153 lines not on this page · raw message
drivers/net/netvsc/meson.build new file +7 -0
Lines of this file are not shown. View the raw message.
drivers/net/netvsc/ndis.h new file +378 -0
378 lines not on this page · raw message
drivers/net/netvsc/rndis.h new file +414 -0
414 lines not on this page · raw message
drivers/net/netvsc/rte_pmd_netvsc_version.map new file +5 -0
Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.18.0
Part of the diff is not shown here. View the raw message.
PATCH v12 4/4 net/netvsc: add documentation
In reply to Stephen HemmingerFrom: Stephen Hemminger <[email protected]>
Matching documentation for new netvsc device.
Includes a brief note about the restart issue.
--- doc/guides/nics/features/netvsc.ini | 23 ++++++ doc/guides/nics/index.rst | 1 + doc/guides/nics/netvsc.rst | 101 +++++++++++++++++++++++++ doc/guides/rel_notes/known_issues.rst | 20 +++++ doc/guides/rel_notes/release_18_08.rst | 6 ++ 5 files changed, 151 insertions(+) create mode 100644 doc/guides/nics/features/netvsc.ini create mode 100644 doc/guides/nics/netvsc.rst
doc/guides/nics/features/netvsc.ini new file +23 -0
@@ -0,0 +1,23 @@ +; +; Supported features of the 'netvsc' network poll mode driver. +; +; Refer to default.ini for the full list of available PMD features. +; +[Features] +Speed capabilities = P +Link status = Y +Queue start/stop = Y +Scattered Rx = Y +Promiscuous mode = Y +Allmulticast mode = Y +Basic stats = Y +Stats per queue = Y +Extended stats = Y +Multiprocess aware = Y +Other kdrv = Y +ARMv7 = Y +ARMv8 = Y +x86-32 = Y +x86-64 = Y +Usage doc = Y +MTU update = Y
doc/guides/nics/index.rst +1 -0
@@ -33,6 +33,7 @@ Network Interface Controller Drivers mlx4 mlx5 mvpp2 + netvsc nfp octeontx qede
doc/guides/nics/netvsc.rst new file +101 -0
101 lines not on this page · raw message
doc/guides/rel_notes/known_issues.rst +20 -0
@@ -739,3 +739,23 @@ Linux kernel 4.10.0 iommu attribute read error **Driver/Module**: ``vfio-pci`` module. + +Netvsc driver and application restart +------------------------------------- + +**Description**: + The Linux kernel uio_hv_generic driver does not completely shutdown and clean up + resources properly if application using Netvsc PMD exits. + +**Implication**: + When application using Netvsc PMD is restarted it can not complete initialization + handshake sequence with the host. + +**Resolution/Workaround**: + Either reboot the guest or remove and reinsert the hv_uio_generic module. + +**Affected Environment/Platform**: + Linux Hyper-V. + +**Driver/Module**: + ``uio_hv_generic`` module.
doc/guides/rel_notes/release_18_08.rst +6 -0
@@ -68,6 +68,12 @@ New Features * Add handlers to add/delete VxLAN port number. * Add devarg to specify ingress VLAN rewrite mode. +* **Added support for Hyper-V netvsc PMD.** + + The new ``netvsc`` poll mode driver provides native support for + networking on Hyper-V. See the :doc:`../nics/netvsc` NIC driver guide + for more details on this new driver. + API Changes -----------
Signature · 1 line
2.18.0
Re: [PATCH v12 3/4] net/netvsc: add hyper-v netvsc network device
In reply to Stephen HemmingerFor information, some cleanup done before pushing:
--- a/MAINTAINERS
+++ b/MAINTAINERS
-F: drivers/net/hyperv/
+F: drivers/net/netvsc/
Unknown symbol:
drivers/bus/vmbus/rte_bus_vmbus_version.map +0 -1
@@ -17,7 +17,6 @@ DPDK_18.08 { rte_vmbus_map_device; rte_vmbus_max_channels; rte_vmbus_probe; - rte_vmbus_probe_one; rte_vmbus_register; rte_vmbus_scan; rte_vmbus_sub_channel_index;
Duplicated includes:
drivers/net/netvsc/hn_ethdev.c +0 -1
@@ -22,7 +22,6 @@#include <rte_cycles.h> #include <rte_errno.h> #include <rte_memory.h> -#include <rte_atomic.h> #include <rte_eal.h> #include <rte_dev.h> #include <rte_bus_vmbus.h>
drivers/net/netvsc/hn_rndis.c +0 -2
@@ -24,8 +24,6 @@#include <rte_memory.h> #include <rte_eal.h> #include <rte_dev.h> -#include <rte_atomic.h> -#include <rte_memory.h> #include <rte_bus_vmbus.h> #include "hn_logs.h"
Thomas Monjalon
Applied13/07/2018 19:06, Stephen Hemminger:
Quoted 21 lines
Final version of the Hyper-V native bus (VMBus)
and network device (netvsc) drivers. This virtual device is used in Microsoft Hyper-V in Windows 10, Windows Server 2016 and Azure. Most of this code was extracted from FreeBSD and some of this is from earlier code donated by Brocade.Only Linux is supported at present, but the code is split to allow future FreeBSD and Windows support.
This version works with upstream kernel (4.16) but in that mode only a single queue is supported. With additional patches that are pending for 5.0 kernel, multi-queue support works as well.
Device binding is best done via driverctl; this required some additional fixes to kernel and driverctl to work correctly. Linux kernel vmbus support needed to support sysfs
driver_overrideand driverctl needed to handle non-PCI bus from udev.
https://gitlab.com/driverctl/driverctl/merge_requests/3
http://driverdev.linuxdriverproject.org/pipermail/driverdev-devel/2018-April/118889.html
Quoted 5 lines
Stephen Hemminger (4):
eal: addrte_uuidsupport
bus/vmbus: add hyper-v virtual bus support
net/netvsc: add hyper-v netvsc network device
net/netvsc: add documentation
Applied, thanks