imx8mq_evk: README: Need to copy bl31.bin to U-Boot source tree
Fabio Estevam
reviewerPATCH 1/3 imx8mq_evk: README: Need to copy bl31.bin to U-Boot source tree
After building ATF it is needed to copy the generated bl31.bin file to the U-Boot source tree.
Make this step explicit in the instructions.
--- board/freescale/imx8mq_evk/README | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
board/freescale/imx8mq_evk/README +2 -1
@@ -9,13 +9,14 @@ Quick Start Get and Build the ARM Trusted firmware ==================== +Note: srctree is U-Boot source directory Get ATF from: https://source.codeaurora.org/external/imx/imx-atf branch: imx_4.14.62_1.0.0_beta $ make PLAT=imx8mq bl31 +$ cp build/imx8mq/release/bl31.bin $(srctree) Get the ddr and hdmi firmware ==================== -Note: srctree is U-Boot source directory $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-7.9.bin $ chmod +x firmware-imx-7.9.bin $ ./firmware-imx-7.9.bin
Signature · 1 line
2.17.1
Fabio Estevam
reviewerPATCH 2/3 imx8mq_evk: README: Fix a typo in the destination path
The DDR firmware binaries should be copied to '$(srctree)', so fix a typo.
--- board/freescale/imx8mq_evk/README | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
board/freescale/imx8mq_evk/README +1 -1
@@ -21,7 +21,7 @@ $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-7.9.bin $ chmod +x firmware-imx-7.9.bin $ ./firmware-imx-7.9.bin $ cp firmware-imx-7.9/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(srctree) -$ cp firmware-imx-7.9/firmware/ddr/synopsys/lpddr4*.bin $(srctee) +$ cp firmware-imx-7.9/firmware/ddr/synopsys/lpddr4*.bin $(srctree) Build U-Boot ====================
Signature · 1 line
2.17.1
PATCH 2/3 imx8mq_evk: README: Fix a typo in the destination path
Quoted 3 lines
The DDR firmware binaries should be copied to '$(srctree)', so fix a typo.
Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
Fabio Estevam
reviewerPATCH 3/3 imx8mq_evk: README: Make the underline marker fill the whole sentence
In reply to Fabio EstevamLet the underline marker "=" fill the whole sentence for better readability.
--- board/freescale/imx8mq_evk/README | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
board/freescale/imx8mq_evk/README +5 -5
@@ -1,14 +1,14 @@ U-Boot for the NXP i.MX8MQ EVK board Quick Start -==================== +=========== - Build the ARM Trusted firmware binary - Get ddr and hdmi fimware - Build U-Boot - Boot Get and Build the ARM Trusted firmware -==================== +====================================== Note: srctree is U-Boot source directory Get ATF from: https://source.codeaurora.org/external/imx/imx-atf branch: imx_4.14.62_1.0.0_beta
@@ -16,7 +16,7 @@ $ make PLAT=imx8mq bl31 $ cp build/imx8mq/release/bl31.bin $(srctree) Get the ddr and hdmi firmware -==================== +============================= $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-7.9.bin $ chmod +x firmware-imx-7.9.bin $ ./firmware-imx-7.9.bin
@@ -24,7 +24,7 @@ $ cp firmware-imx-7.9/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(srctree) $ cp firmware-imx-7.9/firmware/ddr/synopsys/lpddr4*.bin $(srctree) Build U-Boot -==================== +============ $ export CROSS_COMPILE=aarch64-poky-linux- $ make imx8mq_evk_defconfig $ make flash.bin
@@ -33,5 +33,5 @@ Burn the flash.bin to MicroSD card offset 33KB $sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33 Boot -==================== +==== Set Boot switch SW801: 1100 and Bmode: 10 to boot from Micro SD.
Signature · 1 line
2.17.1
PATCH 3/3 imx8mq_evk: README: Make the underline marker fill the whole sentence
Quoted 3 lines
Let the underline marker "=" fill the whole sentence for better readability.
Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH 1/3 imx8mq_evk: README: Need to copy bl31.bin to U-Boot source tree
In reply to Fabio EstevamQuoted 4 lines
After building ATF it is needed to copy the generated bl31.bin file to the U-Boot source tree.
Make this step explicit in the instructions.Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================