Skip to contentSkip to conversation

Add Beelink GS1

PATCH Superseded Clément Péron 2 participants 10 messages Apr 8, 2019 – Apr 12, 2019

Subsystems (3)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

cover Add Beelink GS1

This serie introduce the Beelink GS1 board with a patch for the reset on Allwinner H6.

Thanks to Jagan Teki most of the Beelink GS1 device-tree is taken from the Orange Pi boards.

Clément Péron (4):
arm: dts: h6: move MMC pinctrl to soc
arm: dts: h6: Add Beelink GS1 initial support
arm: sunxi: h6: fix reset using r_wdog
arm: dts: h6: minor sync with linux

 arch/arm/dts/Makefile                         |   1 +
 arch/arm/dts/sun50i-h6-beelink-gs1.dts        | 183 ++++++++++++++++++
 arch/arm/dts/sun50i-h6-orangepi.dtsi          |   2 -
 arch/arm/dts/sun50i-h6-pine-h64.dts           |   4 -
 arch/arm/dts/sun50i-h6.dtsi                   |  16 +-
 .../include/asm/arch-sunxi/cpu_sun50i_h6.h    |   1 +
 arch/arm/mach-sunxi/board.c                   |   9 +-
 configs/beelink_gs1_defconfig                 |  15 ++
 8 files changed, 217 insertions(+), 14 deletions(-)
 create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
 create mode 100644 configs/beelink_gs1_defconfig
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/4 arm: dts: h6: move MMC pinctrl to soc

There is only one muxing avalaible for each MMC controller.

Move this pinmux to the SOC dtsi.

---
 arch/arm/dts/sun50i-h6-orangepi.dtsi | 2 --
 arch/arm/dts/sun50i-h6-pine-h64.dts  | 4 ----
 arch/arm/dts/sun50i-h6.dtsi          | 4 ++++
 3 files changed, 4 insertions(+), 6 deletions(-)
arch/arm/dts/sun50i-h6-orangepi.dtsi +0 -2
index 0612c19cd9..3748dcaa70 100644
@@ -24,8 +24,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_cldo1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
arch/arm/dts/sun50i-h6-pine-h64.dts +0 -4
index ceffc40810..a26314c084 100644
@@ -42,16 +42,12 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_cldo1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
 &mmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins>;
 	vmmc-supply = <&reg_cldo1>;
 	vqmmc-supply = <&reg_bldo2>;
 	non-removable;
arch/arm/dts/sun50i-h6.dtsi +4 -0
index cfa5fffcf6..617cea35d1 100644
@@ -158,6 +158,8 @@
 			resets = <&ccu RST_BUS_MMC0>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -186,6 +188,8 @@
 			resets = <&ccu RST_BUS_MMC2>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc2_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
Signature · 1 line
2.17.1
#2 lore raw

PATCH 1/4 arm: dts: h6: move MMC pinctrl to soc

Quoted 4 lines · Clément Péron

There is only one muxing avalaible for each MMC controller.

Move this pinmux to the SOC dtsi.

Sync all dts(i) changes in one patch with head commit id details on patch commit message instead of few minor updates. sync with some rc tag would be beneficial if needed changes been part of that.

#3 lore raw

PATCH 1/4 arm: dts: h6: move MMC pinctrl to soc

Hi,

Quoted 10 lines · Jagan Teki
Quoted 4 lines · Clément Péron

There is only one muxing avalaible for each MMC controller.

Move this pinmux to the SOC dtsi.

Sync all dts(i) changes in one patch with head commit id details on patch commit message instead of few minor updates. sync with some rc tag would be beneficial if needed changes been part of that.

eMMC pins move patch are planned for 5.2 no rc tag for now... I can postpone the sync dts(i) patch later If you prefer ?

Clement

#4 lore raw

PATCH 2/4 arm: dts: h6: Add Beelink GS1 initial support

In reply to Clément Péron

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)

---
 arch/arm/dts/Makefile                  |   1 +
 arch/arm/dts/sun50i-h6-beelink-gs1.dts | 183 +++++++++++++++++++++++++
 configs/beelink_gs1_defconfig          |  15 ++
 3 files changed, 199 insertions(+)
 create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
 create mode 100644 configs/beelink_gs1_defconfig
arch/arm/dts/Makefile +1 -0
index 0e2ffdb87f..4931b7d3cc 100644
@@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
 	sun50i-h5-orangepi-prime.dtb \
 	sun50i-h5-orangepi-zero-plus2.dtb
 dtb-$(CONFIG_MACH_SUN50I_H6) += \
+	sun50i-h6-beelink-gs1.dtb \
 	sun50i-h6-orangepi-lite2.dtb \
 	sun50i-h6-orangepi-one-plus.dtb \
 	sun50i-h6-pine-h64.dtb
arch/arm/dts/sun50i-h6-beelink-gs1.dts new file +183 -0

183 lines not on this page · raw message

configs/beelink_gs1_defconfig new file +15 -0
new file mode 100644
index 0000000000..ef4dd29549
@@ -0,0 +1,15 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN50I_H6=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+# CONFIG_PSCI_RESET is not set
+CONFIG_NR_DRAM_BANKS=1
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1"
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
Signature · 1 line
2.17.1
#5 lore raw

PATCH 2/4 arm: dts: h6: Add Beelink GS1 initial support

Hi,

Quoted 87 lines · Clément Péron

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)

---
 arch/arm/dts/Makefile                  |   1 +
 arch/arm/dts/sun50i-h6-beelink-gs1.dts | 183 +++++++++++++++++++++++++
 configs/beelink_gs1_defconfig          |  15 ++
 3 files changed, 199 insertions(+)
 create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
 create mode 100644 configs/beelink_gs1_defconfig
arch/arm/dts/Makefile +1 -0
index 0e2ffdb87f..4931b7d3cc 100644
@@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
        sun50i-h5-orangepi-prime.dtb \
        sun50i-h5-orangepi-zero-plus2.dtb
 dtb-$(CONFIG_MACH_SUN50I_H6) += \
+       sun50i-h6-beelink-gs1.dtb \
        sun50i-h6-orangepi-lite2.dtb \
        sun50i-h6-orangepi-one-plus.dtb \
        sun50i-h6-pine-h64.dtb
arch/arm/dts/sun50i-h6-beelink-gs1.dts new file +45 -0
new file mode 100644
index 0000000000..c80862375f
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2019 Clément Péron <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+       model = "Beelink GS1";
+       compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
+
+       aliases {
+               serial0 = &uart0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               power {
+                       label = "beelink:white:power";
+                       gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
+                       default-state = "on";
+               };
+       };
+
+       reg_vcc5v: vcc5v {
+               /* board wide 5V supply directly from the DC jack */
+               compatible = "regulator-fixed";
+               regulator-name = "vcc-5v";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               regulator-always-on;
+       };
+};
+
+&mmc0 {
+       vmmc-supply = <&reg_cldo1>;

arch/arm/dts/sun50i-h6-beelink-gs1.dts line 55

Quoted 10 lines
arch/arm/dts/sun50i-h6-beelink-gs1.dts new file +10 -0
+       cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+       bus-width = <4>;
+       status = "okay";
+};
+
+&mmc2 {
+       vmmc-supply = <&reg_cldo1>;
+       vqmmc-supply = <&reg_bldo2>;
+       non-removable;
+       cap-mmc-hw-reset;

bus-width = <8>;
I missed the bus-width.

The is the same issue on Pine H64

Clement

Quoted 152 lines
arch/arm/dts/sun50i-h6-beelink-gs1.dts new file +128 -0
+       status = "okay";
+};
+
+&r_i2c {
+       status = "okay";
+
+       axp805: pmic at 36 {
+               compatible = "x-powers,axp805", "x-powers,axp806";
+               reg = <0x36>;
+               interrupt-parent = <&r_intc>;
+               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+               interrupt-controller;
+               #interrupt-cells = <1>;
+               x-powers,self-working-mode;
+               vina-supply = <&reg_vcc5v>;
+               vinb-supply = <&reg_vcc5v>;
+               vinc-supply = <&reg_vcc5v>;
+               vind-supply = <&reg_vcc5v>;
+               vine-supply = <&reg_vcc5v>;
+               aldoin-supply = <&reg_vcc5v>;
+               bldoin-supply = <&reg_vcc5v>;
+               cldoin-supply = <&reg_vcc5v>;
+
+               regulators {
+                       reg_aldo1: aldo1 {
+                               regulator-always-on;
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc-pl";
+                       };
+
+                       reg_aldo2: aldo2 {
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc-ac200";
+                               regulator-enable-ramp-delay = <100000>;
+                       };
+
+                       reg_aldo3: aldo3 {
+                               regulator-always-on;
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc25-dram";
+                       };
+
+                       reg_bldo1: bldo1 {
+                               regulator-always-on;
+                               regulator-min-microvolt = <1800000>;
+                               regulator-max-microvolt = <1800000>;
+                               regulator-name = "vcc-bias-pll";
+                       };
+
+                       reg_bldo2: bldo2 {
+                               regulator-always-on;
+                               regulator-min-microvolt = <1800000>;
+                               regulator-max-microvolt = <1800000>;
+                               regulator-name = "vcc-efuse-pcie-hdmi-io";
+                       };
+
+                       reg_bldo3: bldo3 {
+                               regulator-always-on;
+                               regulator-min-microvolt = <1800000>;
+                               regulator-max-microvolt = <1800000>;
+                               regulator-name = "vcc-dcxoio";
+                       };
+
+                       bldo4 {
+                               /* unused */
+                       };
+
+                       reg_cldo1: cldo1 {
+                               regulator-always-on;
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc-3v3";
+                       };
+
+                       reg_cldo2: cldo2 {
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc-wifi-1";
+                       };
+
+                       reg_cldo3: cldo3 {
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc-wifi-2";
+                       };
+
+                       reg_dcdca: dcdca {
+                               regulator-always-on;
+                               regulator-min-microvolt = <810000>;
+                               regulator-max-microvolt = <1080000>;
+                               regulator-name = "vdd-cpu";
+                       };
+
+                       reg_dcdcc: dcdcc {
+                               regulator-min-microvolt = <810000>;
+                               regulator-max-microvolt = <1080000>;
+                               regulator-name = "vdd-gpu";
+                       };
+
+                       reg_dcdcd: dcdcd {
+                               regulator-always-on;
+                               regulator-min-microvolt = <960000>;
+                               regulator-max-microvolt = <960000>;
+                               regulator-name = "vdd-sys";
+                       };
+
+                       reg_dcdce: dcdce {
+                               regulator-always-on;
+                               regulator-min-microvolt = <1200000>;
+                               regulator-max-microvolt = <1200000>;
+                               regulator-name = "vcc-dram";
+                       };
+
+                       sw {
+                               /* unused */
+                       };
+               };
+       };
+};
+
+&uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_ph_pins>;
+       status = "okay";
+};
configs/beelink_gs1_defconfig new file +15 -1
new file mode 100644
index 0000000000..ef4dd29549
@@ -0,0 +1,15 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN50I_H6=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+# CONFIG_PSCI_RESET is not set
+CONFIG_NR_DRAM_BANKS=1
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1"
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
--

2.17.1

#6 lore raw

PATCH 3/4 arm: sunxi: h6: fix reset using r_wdog

In reply to Clément Péron

WDOG in H6 is broken so the reset is actually not working.

Use the R_WDOG instead.

---
 arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h | 1 +
 arch/arm/mach-sunxi/board.c                     | 9 +++++++--
 2 files changed, 8 insertions(+), 2 deletions(-)
arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h +1 -0
index 41a9b0fc47..6392cb07b4 100644
@@ -60,6 +60,7 @@
 #define SUNXI_RTC_BASE			0x07000000
 #define SUNXI_R_CPUCFG_BASE		0x07000400
 #define SUNXI_PRCM_BASE			0x07010000
+#define SUNXI_R_WDOG_BASE		0x07020400
 #define SUNXI_R_PIO_BASE		0x07022000
 #define SUNXI_R_UART_BASE		0x07080000
 #define SUNXI_R_TWI_BASE		0x07081400
arch/arm/mach-sunxi/board.c +7 -2
index b74eaf2a0e..3f8128fbf4 100644
@@ -287,9 +287,14 @@ void reset_cpu(ulong addr)
 		writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
 	}
 #elif defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_MACH_SUN50I_H6)
+#if defined(CONFIG_MACH_SUN50I_H6)
+	/* WDOG is broken for H6 use the R_WDOG instead */
 	static const struct sunxi_wdog *wdog =
-		 ((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
-
+		(struct sunxi_wdog *)SUNXI_R_WDOG_BASE;
+#else
+	static const struct sunxi_wdog *wdog =
+		((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
+#endif
 	/* Set the watchdog for its shortest interval (.5s) and wait */
 	writel(WDT_CFG_RESET, &wdog->cfg);
 	writel(WDT_MODE_EN, &wdog->mode);
Signature · 1 line
2.17.1
#7 lore raw

PATCH 3/4 arm: sunxi: h6: fix reset using r_wdog

+Chen-Yu.

I would like to fix the reset using the R_WDOG instead of WDOG.

What do you think?

If it's acceptable I will propose a similar patch on ATF.

Regards,
Clement

Quoted 47 lines · Clément Péron

WDOG in H6 is broken so the reset is actually not working.

Use the R_WDOG instead.

---
 arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h | 1 +
 arch/arm/mach-sunxi/board.c                     | 9 +++++++--
 2 files changed, 8 insertions(+), 2 deletions(-)
arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h +1 -0
index 41a9b0fc47..6392cb07b4 100644
@@ -60,6 +60,7 @@
 #define SUNXI_RTC_BASE                 0x07000000
 #define SUNXI_R_CPUCFG_BASE            0x07000400
 #define SUNXI_PRCM_BASE                        0x07010000
+#define SUNXI_R_WDOG_BASE              0x07020400
 #define SUNXI_R_PIO_BASE               0x07022000
 #define SUNXI_R_UART_BASE              0x07080000
 #define SUNXI_R_TWI_BASE               0x07081400
arch/arm/mach-sunxi/board.c +7 -3
index b74eaf2a0e..3f8128fbf4 100644
@@ -287,9 +287,14 @@ void reset_cpu(ulong addr)
                writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
        }
 #elif defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_MACH_SUN50I_H6)
+#if defined(CONFIG_MACH_SUN50I_H6)
+       /* WDOG is broken for H6 use the R_WDOG instead */
        static const struct sunxi_wdog *wdog =
-                ((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
-
+               (struct sunxi_wdog *)SUNXI_R_WDOG_BASE;
+#else
+       static const struct sunxi_wdog *wdog =
+               ((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
+#endif
        /* Set the watchdog for its shortest interval (.5s) and wait */
        writel(WDT_CFG_RESET, &wdog->cfg);
        writel(WDT_MODE_EN, &wdog->mode);
--

2.17.1

#8 lore raw

PATCH 3/4 arm: sunxi: h6: fix reset using r_wdog

Hi,

Quoted 6 lines · Clément Péron

+Chen-Yu.

I would like to fix the reset using the R_WDOG instead of WDOG.

What do you think?

Adding information about the issue as explained on ATF:

"
There seems to have a HW errata in the new revision of the SoC. Only SoC used in Pine H64 and Rongpin RP-H6B seems to be NOT affected. Lot of users on OrangePi boards (Lite2 / One Plus and 3) are complaining about this issue.
I personnaly own a Beelink GS1 which has the issue.
My SoC is a H6 V200-AWIN H7309BA 6842
and Chen-Yu Tsai has these two boards :
- Pine h64 with a SoC H6 V200-AWIN H6448BA 7782
- OrangePi Lite 2 with a SoC H6 V200-AWIN H8068BA 61C2
The Pine H64 is working fine but not OPi Lite 2.

I'm not sure if it's an HW errata or not but the result is here WDOG doesn't make these boards reboot properly which should never happen ! "
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/830

Clement

Quoted 52 lines

Regards,
Clement

Quoted 47 lines · Clément Péron

WDOG in H6 is broken so the reset is actually not working.

Use the R_WDOG instead.

---
 arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h | 1 +
 arch/arm/mach-sunxi/board.c                     | 9 +++++++--
 2 files changed, 8 insertions(+), 2 deletions(-)
arch/arm/include/asm/arch-sunxi/cpu_sun50i_h6.h +1 -0
index 41a9b0fc47..6392cb07b4 100644
@@ -60,6 +60,7 @@
 #define SUNXI_RTC_BASE                 0x07000000
 #define SUNXI_R_CPUCFG_BASE            0x07000400
 #define SUNXI_PRCM_BASE                        0x07010000
+#define SUNXI_R_WDOG_BASE              0x07020400
 #define SUNXI_R_PIO_BASE               0x07022000
 #define SUNXI_R_UART_BASE              0x07080000
 #define SUNXI_R_TWI_BASE               0x07081400
arch/arm/mach-sunxi/board.c +7 -3
index b74eaf2a0e..3f8128fbf4 100644
@@ -287,9 +287,14 @@ void reset_cpu(ulong addr)
                writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
        }
 #elif defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_MACH_SUN50I_H6)
+#if defined(CONFIG_MACH_SUN50I_H6)
+       /* WDOG is broken for H6 use the R_WDOG instead */
        static const struct sunxi_wdog *wdog =
-                ((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
-
+               (struct sunxi_wdog *)SUNXI_R_WDOG_BASE;
+#else
+       static const struct sunxi_wdog *wdog =
+               ((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
+#endif
        /* Set the watchdog for its shortest interval (.5s) and wait */
        writel(WDT_CFG_RESET, &wdog->cfg);
        writel(WDT_MODE_EN, &wdog->mode);
--

2.17.1

#9 lore raw

PATCH 4/4 arm: dts: h6: minor sync with linux

In reply to Clément Péron

There are some minor differences between U-Boot and Linux.

Sync only the minor changes.

---
 arch/arm/dts/sun50i-h6.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
arch/arm/dts/sun50i-h6.dtsi +6 -6
index 617cea35d1..5f01314703 100644
@@ -19,28 +19,28 @@
 		#size-cells = <0>;
 
 		cpu0: cpu at 0 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <0>;
 			enable-method = "psci";
 		};
 
 		cpu1: cpu at 1 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <1>;
 			enable-method = "psci";
 		};
 
 		cpu2: cpu at 2 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <2>;
 			enable-method = "psci";
 		};
 
 		cpu3: cpu at 3 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <3>;
 			enable-method = "psci";
@@ -143,7 +143,7 @@
 				bias-pull-up;
 			};
 
-			uart0_ph_pins: uart0-ph {
+			uart0_ph_pins: uart0-ph-pins {
 				pins = "PH0", "PH1";
 				function = "uart0";
 			};
@@ -270,7 +270,7 @@
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
-			r_i2c_pins: r-i2c {
+			r_i2c_pins: r-i2c-pins {
 				pins = "PL0", "PL1";
 				function = "s_i2c";
 			};
Signature · 1 line
2.17.1