Extend mv88e61xx driver to support 88E6071
Subsystems (2)
v2 cover Extend mv88e61xx driver to support 88E6071
This series adds support for 88E6071 switches in the mv88e61xx driver.
Changes in v2:
- fix port init for 6096/6097 devices in patch 1/6
- update commit description in patch 4/6
Anatolij Gustschin (6):
net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
net: phy: mv88e61xx: add CPU port parameter init for 88E6071
net: phy: mv88E61xx: fix ENERGY_DET init for mv88E6071
net: phy: mv88E61xx: add config option for mv88E6071 support
net: phy: mv88e61xx: register phy_driver struct for 88E6071
net: phy: fix switch vendor name
drivers/net/phy/Kconfig | 9 +- drivers/net/phy/mv88e61xx.c | 168 +++++++++++++++++++++++++++--------- 2 files changed, 137 insertions(+), 40 deletions(-)
Signature · 1 line
2.17.1
PATCH v2 1/6 net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
Extend the driver to init switch register offsets from variables instead of compile time macros and enable 88E6071 detection. Ethernet transfer (e.g. tftp) does not work yet, so enable the registration of the 'indirect mii' bus for easier PHY register access by 'mii' command.
--- drivers/net/phy/mv88e61xx.c | 95 +++++++++++++++++++++++++++++-------- 1 file changed, 76 insertions(+), 19 deletions(-)
drivers/net/phy/mv88e61xx.c +76 -19
@@ -39,15 +39,12 @@#define PHY_AUTONEGOTIATE_TIMEOUT 5000 -#define PORT_COUNT 11 -#define PORT_MASK ((1 << PORT_COUNT) - 1) +#define PORT_MASK (port_count) ((1 << (port_count)) - 1)/* Device addresses */ #define DEVADDR_PHY (p) (p) -#define DEVADDR_PORT (p) (0x10 + (p)) +#define DEVADDR_PORT (p) (priv->port_reg_base + (p))#define DEVADDR_SERDES 0x0F -#define DEVADDR_GLOBAL_1 0x1B -#define DEVADDR_GLOBAL_2 0x1C/* SMI indirection registers for multichip addressing mode */ #define SMI_CMD_REG 0x00
@@ -188,11 +185,16 @@#define PORT_SWITCH_ID_6176 0x1760#define PORT_SWITCH_ID_6240 0x2400#define PORT_SWITCH_ID_6352 0x3520 +#define PORT_SWITCH_ID_6071 0x0710struct mv88e61xx_phy_priv {struct mii_dev *mdio_bus;int smi_addr;int id; +int port_count; +int port_reg_base; +u8 global1; +u8 global2; };static inline int smi_cmd (int cmd,int addr,int reg)
@@ -329,11 +331,12 @@ static int mv88e61xx_reg_write(struct phy_device *phydev, int dev, int reg,static int mv88e61xx_phy_wait (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int val;u32 timeout =100 ; do { - val = mv88e61xx_reg_read(phydev, DEVADDR_GLOBAL_2, + val = mv88e61xx_reg_read(phydev, priv->global2, GLOBAL2_REG_PHY_CMD); if (val >= 0 && (val & SMI_BUSY) == 0) return 0;
@@ -347,13 +350,15 @@ static int mv88e61xx_phy_wait(struct phy_device *phydev)static int mv88e61xx_phy_read_indirect (struct mii_dev *smi_wrapper,int dev,int devad,int reg) { +struct mv88e61xx_phy_priv *priv;struct phy_device *phydev;int res; phydev = (struct phy_device *)smi_wrapper->priv; + priv = phydev->priv;/* Issue command to read */ - res =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_2 , + res =mv88e61xx_reg_write (phydev, priv->global2,GLOBAL2_REG_PHY_CMD ,smi_cmd_read (dev, reg));
@@ -363,25 +368,27 @@ static int mv88e61xx_phy_read_indirect(struct mii_dev *smi_wrapper, int dev,return res;/* Read retrieved data */ -return mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_2 , +return mv88e61xx_reg_read (phydev, priv->global2,GLOBAL2_REG_PHY_DATA ); }static int mv88e61xx_phy_write_indirect (struct mii_dev *smi_wrapper,int dev,int devad,int reg,u16 data) { +struct mv88e61xx_phy_priv *priv;struct phy_device *phydev;int res; phydev = (struct phy_device *)smi_wrapper->priv; + priv = phydev->priv;/* Set the data to write */ - res =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_2 , + res =mv88e61xx_reg_write (phydev, priv->global2,GLOBAL2_REG_PHY_DATA , data);if (res <0 )return res;/* Issue the write command */ - res =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_2 , + res =mv88e61xx_reg_write (phydev, priv->global2,GLOBAL2_REG_PHY_CMD ,smi_cmd_write (dev, reg));if (res <0 )
@@ -408,12 +415,14 @@ static int mv88e61xx_phy_write(struct phy_device *phydev, int phy,static int mv88e61xx_port_read (struct phy_device *phydev,u8 port,u8 reg) { +struct mv88e61xx_phy_priv *priv = phydev->priv;return mv88e61xx_reg_read (phydev,DEVADDR_PORT (port), reg); }static int mv88e61xx_port_write (struct phy_device *phydev,u8 port,u8 reg,u16 val) { +struct mv88e61xx_phy_priv *priv = phydev->priv;return mv88e61xx_reg_write (phydev,DEVADDR_PORT (port), reg, val); }
@@ -515,12 +524,13 @@ static int mv88e61xx_parse_status(struct phy_device *phydev)static int mv88e61xx_switch_reset (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int time;int val;u8 port;/* Disable all ports */ -for (port =0 ; port <PORT_COUNT ; port++) { +for (port =0 ; port < priv->port_count; port++) { val =mv88e61xx_port_read (phydev, port,PORT_REG_CTRL );if (val <0 )return val;
@@ -536,18 +546,18 @@ static int mv88e61xx_switch_reset(struct phy_device *phydev)udelay (2000 );/* Reset switch */ - val =mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_1 ,GLOBAL1_CTRL ); + val =mv88e61xx_reg_read (phydev, priv->global1,GLOBAL1_CTRL );if (val <0 )return val; val |=GLOBAL1_CTRL_SWRESET ; - val =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_1 , + val =mv88e61xx_reg_write (phydev, priv->global1,GLOBAL1_CTRL , val);if (val <0 )return val;/* Wait up to 1 second for switch reset complete */ for (time =1000 ; time; time--) { - val =mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_1 , + val =mv88e61xx_reg_read (phydev, priv->global1,GLOBAL1_CTRL );if (val >=0 && ((val &GLOBAL1_CTRL_SWRESET ) ==0 ))break ;
@@ -732,22 +742,23 @@ static int mv88e61xx_fixed_port_setup(struct phy_device *phydev, u8 port)static int mv88e61xx_set_cpu_port (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int val;/* Set CPUDest */ - val =mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_1 ,GLOBAL1_MON_CTRL ); + val =mv88e61xx_reg_read (phydev, priv->global1,GLOBAL1_MON_CTRL );if (val <0 )return val; val =bitfield_replace (val,GLOBAL1_MON_CTRL_CPUDEST_SHIFT ,GLOBAL1_MON_CTRL_CPUDEST_WIDTH ,CONFIG_MV88E61XX_CPU_PORT ); - val =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_1 , + val =mv88e61xx_reg_write (phydev, priv->global1,GLOBAL1_MON_CTRL , val);if (val <0 )return val;/* Allow CPU to route to any port */ - val =PORT_MASK & ~(1 <<CONFIG_MV88E61XX_CPU_PORT ); + val =PORT_MASK (priv->port_count) & ~(1 <<CONFIG_MV88E61XX_CPU_PORT ); val =mv88e61xx_port_set_vlan (phydev,CONFIG_MV88E61XX_CPU_PORT , val);if (val <0 )return val;
@@ -856,6 +867,24 @@ static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy)return 0 ; } +static void mv88e61xx_priv_reg_offs_pre_init (struct mv88e61xx_phy_priv *priv) +{ +/* +* Initial 'port_reg_base' value must be in the port register, +* map and the global_N register offsets must be correct, +* otherwise detection of switch ID won't work! +*/ +#ifndef CONFIG_MV88E61XX_88E6020_FAMILY + priv->global1 =0x1B ; + priv->global2 =0x1C ; + priv->port_reg_base =0x10 ; +#else + priv->global1 =0x0F ; + priv->global2 =0x07 ; + priv->port_reg_base =0x08 ; +#endif +} +static int mv88e61xx_probe (struct phy_device *phydev) {struct mii_dev *smi_wrapper;
@@ -910,13 +939,38 @@ static int mv88e61xx_probe(struct phy_device *phydev) phydev->priv = priv; +mv88e61xx_priv_reg_offs_pre_init (priv); + priv->id =mv88e61xx_get_switch_id (phydev); +debug ("%s ID 0x%x\n" , __func__, priv->id); + +switch (priv->id) { +case PORT_SWITCH_ID_6096 : +case PORT_SWITCH_ID_6097 : +case PORT_SWITCH_ID_6172 : +case PORT_SWITCH_ID_6176 : +case PORT_SWITCH_ID_6240 : +case PORT_SWITCH_ID_6352 : + priv->port_count =11 ; +break ; +case PORT_SWITCH_ID_6071 : + priv->port_count =7 ; +break ; +default : +free (priv); +return -ENODEV ; + } + + res =mdio_register (smi_wrapper); +if (res) +printf ("Failed to register SMI bus\n" );return 0 ; }static int mv88e61xx_phy_config (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int res;int i;int ret =-1 ;
@@ -925,7 +979,7 @@ static int mv88e61xx_phy_config(struct phy_device *phydev)if (res <0 )return res; -for (i =0 ; i <PORT_COUNT ; i++) { +for (i =0 ; i < priv->port_count; i++) {if ((1 << i) &CONFIG_MV88E61XX_PHY_PORTS ) { phydev->addr = i;
@@ -988,13 +1042,14 @@ static int mv88e61xx_phy_is_connected(struct phy_device *phydev)static int mv88e61xx_phy_startup (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int i;int link =0 ;int res;int speed = phydev->speed;int duplex = phydev->duplex; -for (i =0 ; i <PORT_COUNT ; i++) { +for (i =0 ; i < priv->port_count; i++) {if ((1 << i) &CONFIG_MV88E61XX_PHY_PORTS ) { phydev->addr = i;if (!mv88e61xx_phy_is_connected (phydev))
@@ -1068,6 +1123,8 @@ int get_phy_id(struct mii_dev *bus, int smi_addr, int devad, u32 *phy_id) temp_phy.priv = &temp_priv; temp_mii.priv = &temp_phy; +mv88e61xx_priv_reg_offs_pre_init (&temp_priv); + val =mv88e61xx_phy_read_indirect (&temp_mii,0 , devad,MII_PHYSID1 );if (val <0 )return -EIO ;
Signature · 1 line
2.17.1
PATCH v2 1/6 net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
Quoted 18 lines · Anatolij Gustschin
Extend the driver to init switch register offsets from variables instead of compile time macros and enable 88E6071 detection. Ethernet transfer (e.g. tftp) does not work yet, so enable the registration of the 'indirect mii' bus for easier PHY register access by 'mii' command.
Signed-off-by Anatolij Gustschin <[email protected]>--- drivers/net/phy/mv88e61xx.c | 95 +++++++++++++++++++++++++++++-------- 1 file changed, 76 insertions(+), 19 deletions(-)drivers/net/phy/mv88e61xx.c +0
-0@@ -39,15 +39,12 @@
drivers/net/phy/mv88e61xx.c line 46
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +2
-3#define PHY_AUTONEGOTIATE_TIMEOUT 5000 -#define PORT_COUNT 11 -#define PORT_MASK ((1 << PORT_COUNT) - 1) +#define PORT_MASK (port_count) ((1 << (port_count)) - 1)/* Device addresses */ #define DEVADDR_PHY (p) (p) -#define DEVADDR_PORT (p) (0x10 + (p)) +#define DEVADDR_PORT (p) (priv->port_reg_base + (p))
This is an obtuse macro. It should not reference a local variable internally. If you want to use priv, pass it as a parameter.
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +0
-2#define DEVADDR_SERDES 0x0F -#define DEVADDR_GLOBAL_1 0x1B -#define DEVADDR_GLOBAL_2 0x1C/* SMI indirection registers for multichip addressing mode */ #define SMI_CMD_REG 0x00@@ -188,11 +185,16 @@#define PORT_SWITCH_ID_6176 0x1760#define PORT_SWITCH_ID_6240 0x2400#define PORT_SWITCH_ID_6352 0x3520
drivers/net/phy/mv88e61xx.c line 197
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +5
-0+#define PORT_SWITCH_ID_6071 0x0710struct mv88e61xx_phy_priv {struct mii_dev *mdio_bus;int smi_addr;int id; +int port_count; +int port_reg_base; +u8 global1; +u8 global2;
I think this could stand some commenting. global what? Why 2?
Quoted 4 lines
drivers/net/phy/mv88e61xx.c +0
-0};static inline int smi_cmd (int cmd,int addr,int reg)
drivers/net/phy/mv88e61xx.c static int mv88e61xx_reg_write(struct phy_device *phydev, int dev, int reg, · line 339
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +2
-1@@ -329,11 +331,12 @@ static int mv88e61xx_reg_write(struct phy_device *phydev, int dev, int reg, static int mv88e61xx_phy_wait(struct phy_device *phydev) { + struct mv88e61xx_phy_priv *priv = phydev->priv; int val; u32 timeout = 100; do { - val = mv88e61xx_reg_read(phydev, DEVADDR_GLOBAL_2, + val = mv88e61xx_reg_read(phydev, priv->global2,
Probably just use phydev->priv->global2 instead of the local variable.
Quoted 52 lines
drivers/net/phy/mv88e61xx.c +8
-4GLOBAL2_REG_PHY_CMD);if (val >=0 && (val &SMI_BUSY ) ==0 )return 0 ;@@ -347,13 +350,15 @@ static int mv88e61xx_phy_wait(struct phy_device *phydev)static int mv88e61xx_phy_read_indirect (struct mii_dev *smi_wrapper,int dev,int devad,int reg) { +struct mv88e61xx_phy_priv *priv;struct phy_device *phydev;int res; phydev = (struct phy_device *)smi_wrapper->priv; + priv = phydev->priv;/* Issue command to read */ - res =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_2 , + res =mv88e61xx_reg_write (phydev, priv->global2,GLOBAL2_REG_PHY_CMD ,smi_cmd_read (dev, reg));@@ -363,25 +368,27 @@ static int mv88e61xx_phy_read_indirect(struct mii_dev *smi_wrapper, int dev,return res;/* Read retrieved data */ -return mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_2 , +return mv88e61xx_reg_read (phydev, priv->global2,GLOBAL2_REG_PHY_DATA ); }static int mv88e61xx_phy_write_indirect (struct mii_dev *smi_wrapper,int dev,int devad,int reg,u16 data) { +struct mv88e61xx_phy_priv *priv;struct phy_device *phydev;int res; phydev = (struct phy_device *)smi_wrapper->priv; + priv = phydev->priv;/* Set the data to write */ - res =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_2 , + res =mv88e61xx_reg_write (phydev, priv->global2,GLOBAL2_REG_PHY_DATA , data);if (res <0 )return res;/* Issue the write command */ - res =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_2 , + res =mv88e61xx_reg_write (phydev, priv->global2,GLOBAL2_REG_PHY_CMD ,smi_cmd_write (dev, reg));if (res <0 )
drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_write(struct phy_device *phydev, int phy, · line 418
Quoted 4 lines
drivers/net/phy/mv88e61xx.c +1
-0@@ -408,12 +415,14 @@ static int mv88e61xx_phy_write(struct phy_device *phydev, int phy,static int mv88e61xx_port_read (struct phy_device *phydev,u8 port,u8 reg) { +struct mv88e61xx_phy_priv *priv = phydev->priv;
Huh? When casually read, this seems useless.
drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_write(struct phy_device *phydev, int phy, · line 425
Quoted 7 lines
drivers/net/phy/mv88e61xx.c +1
-0return mv88e61xx_reg_read (phydev,DEVADDR_PORT (port), reg); }static int mv88e61xx_port_write (struct phy_device *phydev,u8 port,u8 reg,u16 val) { +struct mv88e61xx_phy_priv *priv = phydev->priv;
Huh? Ditto.
Quoted 68 lines
drivers/net/phy/mv88e61xx.c +9
-7return mv88e61xx_reg_write (phydev,DEVADDR_PORT (port), reg, val); }@@ -515,12 +524,13 @@ static int mv88e61xx_parse_status(struct phy_device *phydev)static int mv88e61xx_switch_reset (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int time;int val;u8 port;/* Disable all ports */ -for (port =0 ; port <PORT_COUNT ; port++) { +for (port =0 ; port < priv->port_count; port++) { val =mv88e61xx_port_read (phydev, port,PORT_REG_CTRL );if (val <0 )return val;@@ -536,18 +546,18 @@ static int mv88e61xx_switch_reset(struct phy_device *phydev)udelay (2000 );/* Reset switch */ - val =mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_1 ,GLOBAL1_CTRL ); + val =mv88e61xx_reg_read (phydev, priv->global1,GLOBAL1_CTRL );if (val <0 )return val; val |=GLOBAL1_CTRL_SWRESET ; - val =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_1 , + val =mv88e61xx_reg_write (phydev, priv->global1,GLOBAL1_CTRL , val);if (val <0 )return val;/* Wait up to 1 second for switch reset complete */ for (time =1000 ; time; time--) { - val =mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_1 , + val =mv88e61xx_reg_read (phydev, priv->global1,GLOBAL1_CTRL );if (val >=0 && ((val &GLOBAL1_CTRL_SWRESET ) ==0 ))break ;@@ -732,22 +742,23 @@ static int mv88e61xx_fixed_port_setup(struct phy_device *phydev, u8 port)static int mv88e61xx_set_cpu_port (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int val;/* Set CPUDest */ - val =mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_1 ,GLOBAL1_MON_CTRL ); + val =mv88e61xx_reg_read (phydev, priv->global1,GLOBAL1_MON_CTRL );if (val <0 )return val; val =bitfield_replace (val,GLOBAL1_MON_CTRL_CPUDEST_SHIFT ,GLOBAL1_MON_CTRL_CPUDEST_WIDTH ,CONFIG_MV88E61XX_CPU_PORT ); - val =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_1 , + val =mv88e61xx_reg_write (phydev, priv->global1,GLOBAL1_MON_CTRL , val);if (val <0 )return val;/* Allow CPU to route to any port */ - val =PORT_MASK & ~(1 <<CONFIG_MV88E61XX_CPU_PORT ); + val =PORT_MASK (priv->port_count) & ~(1 <<CONFIG_MV88E61XX_CPU_PORT ); val =mv88e61xx_port_set_vlan (phydev,CONFIG_MV88E61XX_CPU_PORT , val);if (val <0 )return val;
drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy) · line 874
Quoted 8 lines
drivers/net/phy/mv88e61xx.c +5
-0@@ -856,6 +867,24 @@ static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy)return 0 ; } +static void mv88e61xx_priv_reg_offs_pre_init (struct mv88e61xx_phy_priv *priv) +{ +/* +* Initial 'port_reg_base' value must be in the port register, +* map and the global_N register offsets must be correct,
They are globalN, not global_N. What is the map that this referenced? Please reword.
drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy) · line 875
Quoted 1 line
drivers/net/phy/mv88e61xx.c +1
-0+* otherwise detection of switch ID won't work!
That seems likely... but this looks very magic. Please document it a little better and if possible reference any public datasheets or reference manuals.
drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy) · line 885
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +10
-0+*/ +#ifndef CONFIG_MV88E61XX_88E6020_FAMILY + priv->global1 =0x1B ; + priv->global2 =0x1C ; + priv->port_reg_base =0x10 ; +#else + priv->global1 =0x0F ; + priv->global2 =0x07 ; + priv->port_reg_base =0x08 ; +#endif
I think it would be much cleaner if the contents of this function and the following switch case in the next function were implemented as driver data selections in the udevice_id structure and then used from there.
Quoted 70 lines
drivers/net/phy/mv88e61xx.c +30
-2+} +static int mv88e61xx_probe (struct phy_device *phydev) {struct mii_dev *smi_wrapper;@@ -910,13 +939,38 @@ static int mv88e61xx_probe(struct phy_device *phydev) phydev->priv = priv; +mv88e61xx_priv_reg_offs_pre_init (priv); + priv->id =mv88e61xx_get_switch_id (phydev); +debug ("%s ID 0x%x\n" , __func__, priv->id); + +switch (priv->id) { +case PORT_SWITCH_ID_6096 : +case PORT_SWITCH_ID_6097 : +case PORT_SWITCH_ID_6172 : +case PORT_SWITCH_ID_6176 : +case PORT_SWITCH_ID_6240 : +case PORT_SWITCH_ID_6352 : + priv->port_count =11 ; +break ; +case PORT_SWITCH_ID_6071 : + priv->port_count =7 ; +break ; +default : +free (priv); +return -ENODEV ; + } + + res =mdio_register (smi_wrapper); +if (res) +printf ("Failed to register SMI bus\n" );return 0 ; }static int mv88e61xx_phy_config (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int res;int i;int ret =-1 ;@@ -925,7 +979,7 @@ static int mv88e61xx_phy_config(struct phy_device *phydev)if (res <0 )return res; -for (i =0 ; i <PORT_COUNT ; i++) { +for (i =0 ; i < priv->port_count; i++) {if ((1 << i) &CONFIG_MV88E61XX_PHY_PORTS ) { phydev->addr = i;@@ -988,13 +1042,14 @@ static int mv88e61xx_phy_is_connected(struct phy_device *phydev)static int mv88e61xx_phy_startup (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int i;int link =0 ;int res;int speed = phydev->speed;int duplex = phydev->duplex; -for (i =0 ; i <PORT_COUNT ; i++) { +for (i =0 ; i < priv->port_count; i++) {if ((1 << i) &CONFIG_MV88E61XX_PHY_PORTS ) { phydev->addr = i;if (!mv88e61xx_phy_is_connected (phydev))
drivers/net/phy/mv88e61xx.c int get_phy_id(struct mii_dev *bus, int smi_addr, int devad, u32 *phy_id) · line 1126
Quoted 4 lines
drivers/net/phy/mv88e61xx.c +1
-0@@ -1068,6 +1123,8 @@ int get_phy_id(struct mii_dev *bus, int smi_addr, int devad, u32 *phy_id) temp_phy.priv = &temp_priv; temp_mii.priv = &temp_phy; +mv88e61xx_priv_reg_offs_pre_init (&temp_priv);
Ick.
Quoted 11 lines
drivers/net/phy/mv88e61xx.c +1
-1+ val =mv88e61xx_phy_read_indirect (&temp_mii,0 , devad,MII_PHYSID1 );if (val <0 )return -EIO ; --2.17.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH v2 1/6 net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
Quoted 229 lines · Joe Hershberger
Quoted 18 lines · Anatolij Gustschin
Extend the driver to init switch register offsets from variables instead of compile time macros and enable 88E6071 detection. Ethernet transfer (e.g. tftp) does not work yet, so enable the registration of the 'indirect mii' bus for easier PHY register access by 'mii' command.
Signed-off-by Anatolij Gustschin <[email protected]>--- drivers/net/phy/mv88e61xx.c | 95 +++++++++++++++++++++++++++++-------- 1 file changed, 76 insertions(+), 19 deletions(-)drivers/net/phy/mv88e61xx.c +0
-0@@ -39,15 +39,12 @@drivers/net/phy/mv88e61xx.c line 46
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +2
-3#define PHY_AUTONEGOTIATE_TIMEOUT 5000 -#define PORT_COUNT 11 -#define PORT_MASK ((1 << PORT_COUNT) - 1) +#define PORT_MASK (port_count) ((1 << (port_count)) - 1)/* Device addresses */ #define DEVADDR_PHY (p) (p) -#define DEVADDR_PORT (p) (0x10 + (p)) +#define DEVADDR_PORT (p) (priv->port_reg_base + (p))This is an obtuse macro. It should not reference a local variable internally. If you want to use priv, pass it as a parameter.
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +0
-2#define DEVADDR_SERDES 0x0F -#define DEVADDR_GLOBAL_1 0x1B -#define DEVADDR_GLOBAL_2 0x1C/* SMI indirection registers for multichip addressing mode */ #define SMI_CMD_REG 0x00@@ -188,11 +185,16 @@#define PORT_SWITCH_ID_6176 0x1760#define PORT_SWITCH_ID_6240 0x2400#define PORT_SWITCH_ID_6352 0x3520drivers/net/phy/mv88e61xx.c line 197
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +5
-0+#define PORT_SWITCH_ID_6071 0x0710struct mv88e61xx_phy_priv {struct mii_dev *mdio_bus;int smi_addr;int id; +int port_count; +int port_reg_base; +u8 global1; +u8 global2;I think this could stand some commenting. global what? Why 2?
Quoted 4 lines
drivers/net/phy/mv88e61xx.c +0
-0};static inline int smi_cmd (int cmd,int addr,int reg)drivers/net/phy/mv88e61xx.c static int mv88e61xx_reg_write(struct phy_device *phydev, int dev, int reg, · line 339
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +2
-1@@ -329,11 +331,12 @@ static int mv88e61xx_reg_write(struct phy_device *phydev, int dev, int reg, static int mv88e61xx_phy_wait(struct phy_device *phydev) { + struct mv88e61xx_phy_priv *priv = phydev->priv; int val; u32 timeout = 100; do { - val = mv88e61xx_reg_read(phydev, DEVADDR_GLOBAL_2, + val = mv88e61xx_reg_read(phydev, priv->global2,Probably just use
phydev->priv->global2instead of the local variable.Quoted 52 lines
drivers/net/phy/mv88e61xx.c +8
-4GLOBAL2_REG_PHY_CMD);if (val >=0 && (val &SMI_BUSY ) ==0 )return 0 ;@@ -347,13 +350,15 @@ static int mv88e61xx_phy_wait(struct phy_device *phydev)static int mv88e61xx_phy_read_indirect (struct mii_dev *smi_wrapper,int dev,int devad,int reg) { +struct mv88e61xx_phy_priv *priv;struct phy_device *phydev;int res; phydev = (struct phy_device *)smi_wrapper->priv; + priv = phydev->priv;/* Issue command to read */ - res =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_2 , + res =mv88e61xx_reg_write (phydev, priv->global2,GLOBAL2_REG_PHY_CMD ,smi_cmd_read (dev, reg));@@ -363,25 +368,27 @@ static int mv88e61xx_phy_read_indirect(struct mii_dev *smi_wrapper, int dev,return res;/* Read retrieved data */ -return mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_2 , +return mv88e61xx_reg_read (phydev, priv->global2,GLOBAL2_REG_PHY_DATA ); }static int mv88e61xx_phy_write_indirect (struct mii_dev *smi_wrapper,int dev,int devad,int reg,u16 data) { +struct mv88e61xx_phy_priv *priv;struct phy_device *phydev;int res; phydev = (struct phy_device *)smi_wrapper->priv; + priv = phydev->priv;/* Set the data to write */ - res =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_2 , + res =mv88e61xx_reg_write (phydev, priv->global2,GLOBAL2_REG_PHY_DATA , data);if (res <0 )return res;/* Issue the write command */ - res =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_2 , + res =mv88e61xx_reg_write (phydev, priv->global2,GLOBAL2_REG_PHY_CMD ,smi_cmd_write (dev, reg));if (res <0 )drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_write(struct phy_device *phydev, int phy, · line 418
Quoted 4 lines
drivers/net/phy/mv88e61xx.c +1
-0@@ -408,12 +415,14 @@ static int mv88e61xx_phy_write(struct phy_device *phydev, int phy,static int mv88e61xx_port_read (struct phy_device *phydev,u8 port,u8 reg) { +struct mv88e61xx_phy_priv *priv = phydev->priv;Huh? When casually read, this seems useless.
drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_write(struct phy_device *phydev, int phy, · line 425
Quoted 7 lines
drivers/net/phy/mv88e61xx.c +1
-0return mv88e61xx_reg_read (phydev,DEVADDR_PORT (port), reg); }static int mv88e61xx_port_write (struct phy_device *phydev,u8 port,u8 reg,u16 val) { +struct mv88e61xx_phy_priv *priv = phydev->priv;Huh? Ditto.
Quoted 68 lines
drivers/net/phy/mv88e61xx.c +9
-7return mv88e61xx_reg_write (phydev,DEVADDR_PORT (port), reg, val); }@@ -515,12 +524,13 @@ static int mv88e61xx_parse_status(struct phy_device *phydev)static int mv88e61xx_switch_reset (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int time;int val;u8 port;/* Disable all ports */ -for (port =0 ; port <PORT_COUNT ; port++) { +for (port =0 ; port < priv->port_count; port++) { val =mv88e61xx_port_read (phydev, port,PORT_REG_CTRL );if (val <0 )return val;@@ -536,18 +546,18 @@ static int mv88e61xx_switch_reset(struct phy_device *phydev)udelay (2000 );/* Reset switch */ - val =mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_1 ,GLOBAL1_CTRL ); + val =mv88e61xx_reg_read (phydev, priv->global1,GLOBAL1_CTRL );if (val <0 )return val; val |=GLOBAL1_CTRL_SWRESET ; - val =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_1 , + val =mv88e61xx_reg_write (phydev, priv->global1,GLOBAL1_CTRL , val);if (val <0 )return val;/* Wait up to 1 second for switch reset complete */ for (time =1000 ; time; time--) { - val =mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_1 , + val =mv88e61xx_reg_read (phydev, priv->global1,GLOBAL1_CTRL );if (val >=0 && ((val &GLOBAL1_CTRL_SWRESET ) ==0 ))break ;@@ -732,22 +742,23 @@ static int mv88e61xx_fixed_port_setup(struct phy_device *phydev, u8 port)static int mv88e61xx_set_cpu_port (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int val;/* Set CPUDest */ - val =mv88e61xx_reg_read (phydev,DEVADDR_GLOBAL_1 ,GLOBAL1_MON_CTRL ); + val =mv88e61xx_reg_read (phydev, priv->global1,GLOBAL1_MON_CTRL );if (val <0 )return val; val =bitfield_replace (val,GLOBAL1_MON_CTRL_CPUDEST_SHIFT ,GLOBAL1_MON_CTRL_CPUDEST_WIDTH ,CONFIG_MV88E61XX_CPU_PORT ); - val =mv88e61xx_reg_write (phydev,DEVADDR_GLOBAL_1 , + val =mv88e61xx_reg_write (phydev, priv->global1,GLOBAL1_MON_CTRL , val);if (val <0 )return val;/* Allow CPU to route to any port */ - val =PORT_MASK & ~(1 <<CONFIG_MV88E61XX_CPU_PORT ); + val =PORT_MASK (priv->port_count) & ~(1 <<CONFIG_MV88E61XX_CPU_PORT ); val =mv88e61xx_port_set_vlan (phydev,CONFIG_MV88E61XX_CPU_PORT , val);if (val <0 )return val;drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy) · line 874
Quoted 8 lines
drivers/net/phy/mv88e61xx.c +5
-0@@ -856,6 +867,24 @@ static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy)return 0 ; } +static void mv88e61xx_priv_reg_offs_pre_init (struct mv88e61xx_phy_priv *priv) +{ +/* +* Initial 'port_reg_base' value must be in the port register, +* map and the global_N register offsets must be correct, They are globalN, not
global_N. What is the map that this referenced? Please reword.drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy) · line 875
Quoted 1 line
drivers/net/phy/mv88e61xx.c +1
-0+* otherwise detection of switch ID won't work! That seems likely... but this looks very magic. Please document it a little better and if possible reference any public datasheets or reference manuals.
Quoted 15 lines
drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy) · line 885
Quoted 10 lines
drivers/net/phy/mv88e61xx.c +10
-0+*/ +#ifndef CONFIG_MV88E61XX_88E6020_FAMILY + priv->global1 =0x1B ; + priv->global2 =0x1C ; + priv->port_reg_base =0x10 ; +#else + priv->global1 =0x0F ; + priv->global2 =0x07 ; + priv->port_reg_base =0x08 ; +#endif I think it would be much cleaner if the contents of this function and the following switch case in the next function were implemented as driver data selections in the
udevice_idstructure and then used from there.
Argh... I forgot phy is not using DM yet. Nvm.
Quoted 92 lines
Quoted 70 lines
drivers/net/phy/mv88e61xx.c +30
-2+} +static int mv88e61xx_probe (struct phy_device *phydev) {struct mii_dev *smi_wrapper;@@ -910,13 +939,38 @@ static int mv88e61xx_probe(struct phy_device *phydev) phydev->priv = priv; +mv88e61xx_priv_reg_offs_pre_init (priv); + priv->id =mv88e61xx_get_switch_id (phydev); +debug ("%s ID 0x%x\n" , __func__, priv->id); + +switch (priv->id) { +case PORT_SWITCH_ID_6096 : +case PORT_SWITCH_ID_6097 : +case PORT_SWITCH_ID_6172 : +case PORT_SWITCH_ID_6176 : +case PORT_SWITCH_ID_6240 : +case PORT_SWITCH_ID_6352 : + priv->port_count =11 ; +break ; +case PORT_SWITCH_ID_6071 : + priv->port_count =7 ; +break ; +default : +free (priv); +return -ENODEV ; + } + + res =mdio_register (smi_wrapper); +if (res) +printf ("Failed to register SMI bus\n" );return 0 ; }static int mv88e61xx_phy_config (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int res;int i;int ret =-1 ;@@ -925,7 +979,7 @@ static int mv88e61xx_phy_config(struct phy_device *phydev)if (res <0 )return res; -for (i =0 ; i <PORT_COUNT ; i++) { +for (i =0 ; i < priv->port_count; i++) {if ((1 << i) &CONFIG_MV88E61XX_PHY_PORTS ) { phydev->addr = i;@@ -988,13 +1042,14 @@ static int mv88e61xx_phy_is_connected(struct phy_device *phydev)static int mv88e61xx_phy_startup (struct phy_device *phydev) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int i;int link =0 ;int res;int speed = phydev->speed;int duplex = phydev->duplex; -for (i =0 ; i <PORT_COUNT ; i++) { +for (i =0 ; i < priv->port_count; i++) {if ((1 << i) &CONFIG_MV88E61XX_PHY_PORTS ) { phydev->addr = i;if (!mv88e61xx_phy_is_connected (phydev))drivers/net/phy/mv88e61xx.c int get_phy_id(struct mii_dev *bus, int smi_addr, int devad, u32 *phy_id) · line 1126
Quoted 4 lines
drivers/net/phy/mv88e61xx.c +1
-0@@ -1068,6 +1123,8 @@ int get_phy_id(struct mii_dev *bus, int smi_addr, int devad, u32 *phy_id) temp_phy.priv = &temp_priv; temp_mii.priv = &temp_phy; +mv88e61xx_priv_reg_offs_pre_init (&temp_priv);Ick.
Quoted 11 lines
drivers/net/phy/mv88e61xx.c +1
-1+ val =mv88e61xx_phy_read_indirect (&temp_mii,0 , devad,MII_PHYSID1 );if (val <0 )return -EIO ; --2.17.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH v2 1/6 net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
Quoted 11 lines · On Tue, 23 Jul 2019 04:07:04 +0000 Joe Hershberger joe.hershberger at ni.com…
Quoted 11 lines
drivers/net/phy/mv88e61xx.c static int mv88e61xx_reg_write(struct phy_device *phydev, int dev, int reg, · line 339
Quoted 9 lines
static int
mv88e61xx_phy_wait(struct phy_device *phydev){drivers/net/phy/mv88e61xx.c +2
-1+struct mv88e61xx_phy_priv *priv = phydev->priv;int val;u32 timeout =100 ; do { - val = mv88e61xx_reg_read(phydev, DEVADDR_GLOBAL_2, + val = mv88e61xx_reg_read(phydev, priv->global2,Probably just use
phydev->priv->global2instead of the local variable.
No, I'll stick with local variable. priv is void*, we will get
+drivers/net/phy/mv88e61xx.c:338:48: error: dereferencing 'void *' pointer [-Werror]
+ val = mv88e61xx_reg_read(phydev, phydev->priv->global2,
--
Anatolij
PATCH v2 1/6 net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
Quoted 18 lines · Anatolij Gustschin
Quoted 11 lines · On Tue, 23 Jul 2019 04:07:04 +0000 Joe Hershberger joe.hershberger at ni.com…
Quoted 11 lines
drivers/net/phy/mv88e61xx.c static int mv88e61xx_reg_write(struct phy_device *phydev, int dev, int reg, · line 339
Quoted 9 lines
static int
mv88e61xx_phy_wait(struct phy_device *phydev){drivers/net/phy/mv88e61xx.c +2
-1+struct mv88e61xx_phy_priv *priv = phydev->priv;int val;u32 timeout =100 ; do { - val = mv88e61xx_reg_read(phydev, DEVADDR_GLOBAL_2, + val = mv88e61xx_reg_read(phydev, priv->global2,Probably just use
phydev->priv->global2instead of the local variable.No, I'll stick with local variable. priv is void*, we will get
Review
Quoted 2 lines
(quoted diff) +2
-0+drivers/net/phy/mv88e61xx.c:338:48: error: dereferencing 'void *' pointer [-Werror] + val = mv88e61xx_reg_read(phydev, phydev->priv->global2,
Ah, ok.
-Joe
PATCH v2 1/6 net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
In reply to Joe HershbergerOn Tue, 23 Jul 2019 04:08:23 +0000
Joe Hershberger joe.hershberger at ni.com wrote:
...
Quoted 5 lines
drivers/net/phy/mv88e61xx.c line 46
Quoted 2 lines
drivers/net/phy/mv88e61xx.c +1
-1-#define DEVADDR_PORT (p) (0x10 + (p)) +#define DEVADDR_PORT (p) (priv->port_reg_base + (p))This is an obtuse macro. It should not reference a local variable internally. If you want to use priv, pass it as a parameter.
Okay.
Quoted 10 lines
drivers/net/phy/mv88e61xx.c line 197
Quoted 8 lines
struct mv88e61xx_phy_priv { struct mii_dev *mdio_bus; int smi_addr; int id;drivers/net/phy/mv88e61xx.c +4
-0+int port_count; +int port_reg_base; +u8 global1; +u8 global2;I think this could stand some commenting. global what? Why 2?
I'll add some comments here.
...
Quoted 11 lines
drivers/net/phy/mv88e61xx.c static int mv88e61xx_reg_write(struct phy_device *phydev, int dev, int reg, · line 339
Quoted 9 lines
static int
mv88e61xx_phy_wait(struct phy_device *phydev){drivers/net/phy/mv88e61xx.c +2
-1+struct mv88e61xx_phy_priv *priv = phydev->priv;int val;u32 timeout =100 ; do { - val = mv88e61xx_reg_read(phydev, DEVADDR_GLOBAL_2, + val = mv88e61xx_reg_read(phydev, priv->global2,Probably just use
phydev->priv->global2instead of the local variable.
Done in v3.
...
Quoted 5 lines
Quoted 3 lines
static int
mv88e61xx_port_read(struct phy_device *phydev, u8 port, u8 reg){
+ structmv88e61xx_phy_priv*priv =phydev->priv;Huh? When casually read, this seems useless.
Okay, I'll remove DEVADDR_PORT() macro.
...
Quoted 6 lines
Quoted 4 lines
static int mv88e61xx_port_write(struct
phy_device*phydev, u8 port, u8 reg,u16 val){
+ structmv88e61xx_phy_priv*priv =phydev->priv;Huh? Ditto.
Will fix it.
...
Quoted 8 lines
drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy) · line 874
Quoted 5 lines
drivers/net/phy/mv88e61xx.c +5
-0+static void mv88e61xx_priv_reg_offs_pre_init (struct mv88e61xx_phy_priv *priv) +{ +/* +* Initial 'port_reg_base' value must be in the port register, +* map and the global_N register offsets must be correct, They are globalN, not
global_N. What is the map that this referenced? Please reword.
Okay, done in v3.
Quoted 5 lines
Quoted 1 line
+ * otherwise detection of switch ID won't work!
That seems likely... but this looks very magic. Please document it a little better and if possible reference any public datasheets or reference manuals.
Will add more comments here. The datasheets or manuals are all under NDA, I can't add references here.
Quoted 7 lines
Quoted 7 lines
drivers/net/phy/mv88e61xx.c +7
-0+*/ +#ifndef CONFIG_MV88E61XX_88E6020_FAMILY + priv->global1 =0x1B ; + priv->global2 =0x1C ; + priv->port_reg_base =0x10 ; +#else + priv->global1 =0x0F ;
Quoted 8 lines
drivers/net/phy/mv88e61xx.c static int mv88e61xx_phy_config_port(struct phy_device *phydev, u8 phy) · line 885
Quoted 3 lines
drivers/net/phy/mv88e61xx.c +3
-0+ priv->global2 =0x07 ; + priv->port_reg_base =0x08 ; +#endif I think it would be much cleaner if the contents of this function and the following switch case in the next function were implemented as driver data selections in the
udevice_idstructure and then used from there.
The problem is that this offset pre-initialisation is also required before the actual driver probing (i.e. calls of get_phy_id() from PHY framework).
...
Quoted 7 lines
drivers/net/phy/mv88e61xx.c int get_phy_id(struct mii_dev *bus, int smi_addr, int devad, u32 *phy_id) · line 1126
Quoted 5 lines
drivers/net/phy/mv88e61xx.c +1
-0@@ -1068,6 +1123,8 @@ int get_phy_id(struct mii_dev *bus, int smi_addr, int devad, u32 *phy_id) temp_phy.priv = &temp_priv; temp_mii.priv = &temp_phy; +mv88e61xx_priv_reg_offs_pre_init (&temp_priv);Ick.
will add a comment why it is required here.
--
Anatolij
PATCH v2 2/6 net: phy: mv88e61xx: add CPU port parameter init for 88E6071
In reply to Anatolij GustschinOn 88E6071 chip the port status register bit field offsets for duplex and link bits differ. Extend the driver to use 88E6071 specific offset values. The width of bit fields for speed status differ, too. Adapt for proper port speed detection on 88E6071.
--- drivers/net/phy/mv88e61xx.c | 41 +++++++++++++++++++++++++------------ 1 file changed, 28 insertions(+), 13 deletions(-)
drivers/net/phy/mv88e61xx.c +28 -13
@@ -85,9 +85,6 @@#define GLOBAL1_MON_CTRL_CPUDEST_SHIFT 4#define GLOBAL1_MON_CTRL_CPUDEST_WIDTH 4 -#define PORT_REG_STATUS_LINK BIT(11) -#define PORT_REG_STATUS_DUPLEX BIT(10) -#define PORT_REG_STATUS_SPEED_SHIFT 8#define PORT_REG_STATUS_SPEED_WIDTH 2#define PORT_REG_STATUS_SPEED_10 0
@@ -108,6 +105,7 @@#define PORT_REG_PHYS_CTRL_DUPLEX_VALUE BIT(3)#define PORT_REG_PHYS_CTRL_DUPLEX_FORCE BIT(2)#define PORT_REG_PHYS_CTRL_SPD1000 BIT(1) +#define PORT_REG_PHYS_CTRL_SPD100 BIT(0)#define PORT_REG_PHYS_CTRL_SPD_MASK (BIT(1) | BIT(0))#define PORT_REG_CTRL_PSTATE_SHIFT 0
@@ -193,6 +191,9 @@ struct mv88e61xx_phy_priv {int id;int port_count;int port_reg_base; +u16 port_stat_link_mask; +u16 port_stat_dup_mask; +u8 port_stat_speed_width;u8 global1;u8 global2; };
@@ -638,6 +639,7 @@ static int mv88e61xx_port_set_vlan(struct phy_device *phydev, u8 port,static int mv88e61xx_read_port_config (struct phy_device *phydev,u8 port) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int res;int val;bool forced = false;
@@ -645,7 +647,7 @@ static int mv88e61xx_read_port_config(struct phy_device *phydev, u8 port) val =mv88e61xx_port_read (phydev, port,PORT_REG_STATUS );if (val <0 )return val; -if (!(val &PORT_REG_STATUS_LINK )) { +if (!(val & priv->port_stat_link_mask)) {/* Temporarily force link to read port configuration */ u32 timeout =100 ; forced = true;
@@ -668,7 +670,7 @@ static int mv88e61xx_read_port_config(struct phy_device *phydev, u8 port) res = -EIO ; goto unforce; } -if (val &PORT_REG_STATUS_LINK ) +if (val & priv->port_stat_link_mask)break ; }while (--timeout);
@@ -678,13 +680,13 @@ static int mv88e61xx_read_port_config(struct phy_device *phydev, u8 port) } } -if (val &PORT_REG_STATUS_DUPLEX ) +if (val & priv->port_stat_dup_mask) phydev->duplex =DUPLEX_FULL ;else phydev->duplex =DUPLEX_HALF ; val =bitfield_extract (val,PORT_REG_STATUS_SPEED_SHIFT , -PORT_REG_STATUS_SPEED_WIDTH ); + priv->port_stat_speed_width);switch (val) {case PORT_REG_STATUS_SPEED_1000 : phydev->speed =SPEED_1000 ;
@@ -717,6 +719,7 @@ unforce:static int mv88e61xx_fixed_port_setup (struct phy_device *phydev,u8 port) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int val; val =mv88e61xx_port_read (phydev, port,PORT_REG_PHYS_CTRL );
@@ -724,13 +727,19 @@ static int mv88e61xx_fixed_port_setup(struct phy_device *phydev, u8 port)return val; val &= ~(PORT_REG_PHYS_CTRL_SPD_MASK | -PORT_REG_PHYS_CTRL_FC_VALUE ); - val |=PORT_REG_PHYS_CTRL_PCS_AN_EN | -PORT_REG_PHYS_CTRL_PCS_AN_RST | -PORT_REG_PHYS_CTRL_FC_FORCE | +PORT_REG_PHYS_CTRL_FC_VALUE | +PORT_REG_PHYS_CTRL_FC_FORCE ); + val |=PORT_REG_PHYS_CTRL_FC_FORCE |PORT_REG_PHYS_CTRL_DUPLEX_VALUE | -PORT_REG_PHYS_CTRL_DUPLEX_FORCE | -PORT_REG_PHYS_CTRL_SPD1000 ; +PORT_REG_PHYS_CTRL_DUPLEX_FORCE ; + +if (priv->id ==PORT_SWITCH_ID_6071 ) { + val |=PORT_REG_PHYS_CTRL_SPD100 ; + }else { + val |=PORT_REG_PHYS_CTRL_PCS_AN_EN | +PORT_REG_PHYS_CTRL_PCS_AN_RST | +PORT_REG_PHYS_CTRL_SPD1000 ; + }if (port ==CONFIG_MV88E61XX_CPU_PORT ) val |= PORT_REG_PHYS_CTRL_LINK_VALUE |
@@ -952,9 +961,15 @@ static int mv88e61xx_probe(struct phy_device *phydev)case PORT_SWITCH_ID_6240 :case PORT_SWITCH_ID_6352 : priv->port_count =11 ; + priv->port_stat_link_mask =BIT (11 ); + priv->port_stat_dup_mask =BIT (10 ); + priv->port_stat_speed_width =2 ;break ;case PORT_SWITCH_ID_6071 : priv->port_count =7 ; + priv->port_stat_link_mask =BIT (12 ); + priv->port_stat_dup_mask =BIT (9 ); + priv->port_stat_speed_width =1 ;break ;default :free (priv);
Signature · 1 line
2.17.1
PATCH v2 2/6 net: phy: mv88e61xx: add CPU port parameter init for 88E6071
Quoted 17 lines · Anatolij Gustschin
On 88E6071 chip the port status register bit field offsets for duplex and link bits differ. Extend the driver to use 88E6071 specific offset values. The width of bit fields for speed status differ, too. Adapt for proper port speed detection on 88E6071.
Signed-off-by Anatolij Gustschin <[email protected]>--- drivers/net/phy/mv88e61xx.c | 41 +++++++++++++++++++++++++------------ 1 file changed, 28 insertions(+), 13 deletions(-)drivers/net/phy/mv88e61xx.c +0
-0
drivers/net/phy/mv88e61xx.c line 89
Quoted 8 lines
drivers/net/phy/mv88e61xx.c +0
-3@@ -85,9 +85,6 @@#define GLOBAL1_MON_CTRL_CPUDEST_SHIFT 4#define GLOBAL1_MON_CTRL_CPUDEST_WIDTH 4 -#define PORT_REG_STATUS_LINK BIT(11) -#define PORT_REG_STATUS_DUPLEX BIT(10) -#define PORT_REG_STATUS_SPEED_SHIFT 8#define PORT_REG_STATUS_SPEED_WIDTH 2
Surprised this didn't go away.
Quoted 118 lines
drivers/net/phy/mv88e61xx.c +28
-11#define PORT_REG_STATUS_SPEED_10 0@@ -108,6 +105,7 @@#define PORT_REG_PHYS_CTRL_DUPLEX_VALUE BIT(3)#define PORT_REG_PHYS_CTRL_DUPLEX_FORCE BIT(2)#define PORT_REG_PHYS_CTRL_SPD1000 BIT(1) +#define PORT_REG_PHYS_CTRL_SPD100 BIT(0)#define PORT_REG_PHYS_CTRL_SPD_MASK (BIT(1) | BIT(0))#define PORT_REG_CTRL_PSTATE_SHIFT 0@@ -193,6 +191,9 @@ struct mv88e61xx_phy_priv {int id;int port_count;int port_reg_base; +u16 port_stat_link_mask; +u16 port_stat_dup_mask; +u8 port_stat_speed_width;u8 global1;u8 global2; };@@ -638,6 +639,7 @@ static int mv88e61xx_port_set_vlan(struct phy_device *phydev, u8 port,static int mv88e61xx_read_port_config (struct phy_device *phydev,u8 port) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int res;int val;bool forced = false;@@ -645,7 +647,7 @@ static int mv88e61xx_read_port_config(struct phy_device *phydev, u8 port) val =mv88e61xx_port_read (phydev, port,PORT_REG_STATUS );if (val <0 )return val; -if (!(val &PORT_REG_STATUS_LINK )) { +if (!(val & priv->port_stat_link_mask)) {/* Temporarily force link to read port configuration */ u32 timeout =100 ; forced = true;@@ -668,7 +670,7 @@ static int mv88e61xx_read_port_config(struct phy_device *phydev, u8 port) res = -EIO ; goto unforce; } -if (val &PORT_REG_STATUS_LINK ) +if (val & priv->port_stat_link_mask)break ; }while (--timeout);@@ -678,13 +680,13 @@ static int mv88e61xx_read_port_config(struct phy_device *phydev, u8 port) } } -if (val &PORT_REG_STATUS_DUPLEX ) +if (val & priv->port_stat_dup_mask) phydev->duplex =DUPLEX_FULL ;else phydev->duplex =DUPLEX_HALF ; val =bitfield_extract (val,PORT_REG_STATUS_SPEED_SHIFT , -PORT_REG_STATUS_SPEED_WIDTH ); + priv->port_stat_speed_width);switch (val) {case PORT_REG_STATUS_SPEED_1000 : phydev->speed =SPEED_1000 ;@@ -717,6 +719,7 @@ unforce:static int mv88e61xx_fixed_port_setup (struct phy_device *phydev,u8 port) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int val; val =mv88e61xx_port_read (phydev, port,PORT_REG_PHYS_CTRL );@@ -724,13 +727,19 @@ static int mv88e61xx_fixed_port_setup(struct phy_device *phydev, u8 port)return val; val &= ~(PORT_REG_PHYS_CTRL_SPD_MASK | -PORT_REG_PHYS_CTRL_FC_VALUE ); - val |=PORT_REG_PHYS_CTRL_PCS_AN_EN | -PORT_REG_PHYS_CTRL_PCS_AN_RST | -PORT_REG_PHYS_CTRL_FC_FORCE | +PORT_REG_PHYS_CTRL_FC_VALUE | +PORT_REG_PHYS_CTRL_FC_FORCE ); + val |=PORT_REG_PHYS_CTRL_FC_FORCE |PORT_REG_PHYS_CTRL_DUPLEX_VALUE | -PORT_REG_PHYS_CTRL_DUPLEX_FORCE | -PORT_REG_PHYS_CTRL_SPD1000 ; +PORT_REG_PHYS_CTRL_DUPLEX_FORCE ; + +if (priv->id ==PORT_SWITCH_ID_6071 ) { + val |=PORT_REG_PHYS_CTRL_SPD100 ; + }else { + val |=PORT_REG_PHYS_CTRL_PCS_AN_EN | +PORT_REG_PHYS_CTRL_PCS_AN_RST | +PORT_REG_PHYS_CTRL_SPD1000 ; + }if (port ==CONFIG_MV88E61XX_CPU_PORT ) val |= PORT_REG_PHYS_CTRL_LINK_VALUE |@@ -952,9 +961,15 @@ static int mv88e61xx_probe(struct phy_device *phydev)case PORT_SWITCH_ID_6240 :case PORT_SWITCH_ID_6352 : priv->port_count =11 ; + priv->port_stat_link_mask =BIT (11 ); + priv->port_stat_dup_mask =BIT (10 ); + priv->port_stat_speed_width =2 ;break ;case PORT_SWITCH_ID_6071 : priv->port_count =7 ; + priv->port_stat_link_mask =BIT (12 ); + priv->port_stat_dup_mask =BIT (9 ); + priv->port_stat_speed_width =1 ;break ;default :free (priv); --2.17.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH v2 2/6 net: phy: mv88e61xx: add CPU port parameter init for 88E6071
On Tue, 23 Jul 2019 04:05:56 +0000
Joe Hershberger joe.hershberger at ni.com wrote:
...
Quoted 7 lines
drivers/net/phy/mv88e61xx.c line 89
Quoted 5 lines
drivers/net/phy/mv88e61xx.c +0
-3-#define PORT_REG_STATUS_LINK BIT(11) -#define PORT_REG_STATUS_DUPLEX BIT(10) -#define PORT_REG_STATUS_SPEED_SHIFT 8#define PORT_REG_STATUS_SPEED_WIDTH 2Surprised this didn't go away.
Removed in v3, thanks.
--
Anatolij
PATCH v2 3/6 net: phy: mv88E61xx: fix ENERGY_DET init for mv88E6071
In reply to Anatolij GustschinOn mv88E6071 the 'EDet' field offset, width and sense control bits are different, adjust the driver to init the PHY control register as needed. This fixes not working link detection and tftp transfers.
--- drivers/net/phy/mv88e61xx.c | 20 +++++++++++++------- 1 file changed, 13 insertions(+), 7 deletions(-)
drivers/net/phy/mv88e61xx.c +13 -7
@@ -119,16 +119,12 @@#define SERDES_REG_CTRL_1_FORCE_LINK BIT(10) -#define PHY_REG_CTRL1_ENERGY_DET_SHIFT 8 -#define PHY_REG_CTRL1_ENERGY_DET_WIDTH 2 -/* Field values */ #define PORT_REG_CTRL_PSTATE_DISABLED 0#define PORT_REG_CTRL_PSTATE_FORWARD 3#define PHY_REG_CTRL1_ENERGY_DET_OFF 0#define PHY_REG_CTRL1_ENERGY_DET_SENSE_ONLY 2 -#define PHY_REG_CTRL1_ENERGY_DET_SENSE_XMIT 3/* PHY Status Register */ #define PHY_REG_STATUS1_SPEED 0xc000
@@ -194,6 +190,9 @@ struct mv88e61xx_phy_priv {u16 port_stat_link_mask;u16 port_stat_dup_mask;u8 port_stat_speed_width; +u8 phy_ctrl1_en_det_shift; +u8 phy_ctrl1_en_det_width; +u8 phy_ctrl1_en_det_sense_xmit;u8 global1;u8 global2; };
@@ -841,6 +840,7 @@ static int mv88e61xx_phy_enable(struct phy_device *phydev, u8 phy)static int mv88e61xx_phy_setup (struct phy_device *phydev,u8 phy) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int val;/*
@@ -850,9 +850,9 @@ static int mv88e61xx_phy_setup(struct phy_device *phydev, u8 phy) val =mv88e61xx_phy_read (phydev, phy,PHY_REG_CTRL1 );if (val <0 )return val; - val =bitfield_replace (val,PHY_REG_CTRL1_ENERGY_DET_SHIFT , -PHY_REG_CTRL1_ENERGY_DET_WIDTH , -PHY_REG_CTRL1_ENERGY_DET_SENSE_XMIT ); + val =bitfield_replace (val, priv->phy_ctrl1_en_det_shift, + priv->phy_ctrl1_en_det_width, + priv->phy_ctrl1_en_det_sense_xmit); val =mv88e61xx_phy_write (phydev, phy,PHY_REG_CTRL1 , val);if (val <0 )return val;
@@ -964,12 +964,18 @@ static int mv88e61xx_probe(struct phy_device *phydev) priv->port_stat_link_mask =BIT (11 ); priv->port_stat_dup_mask =BIT (10 ); priv->port_stat_speed_width =2 ; + priv->phy_ctrl1_en_det_shift =8 ; + priv->phy_ctrl1_en_det_width =2 ; + priv->phy_ctrl1_en_det_sense_xmit =3 ;break ;case PORT_SWITCH_ID_6071 : priv->port_count =7 ; priv->port_stat_link_mask =BIT (12 ); priv->port_stat_dup_mask =BIT (9 ); priv->port_stat_speed_width =1 ; + priv->phy_ctrl1_en_det_shift =14 ; + priv->phy_ctrl1_en_det_width =1 ; + priv->phy_ctrl1_en_det_sense_xmit =1 ;break ;default :free (priv);
Signature · 1 line
2.17.1
PATCH v2 3/6 net: phy: mv88E61xx: fix ENERGY_DET init for mv88E6071
Quoted 5 lines · Anatolij Gustschin
On mv88E6071 the 'EDet' field offset, width and sense control bits are different, adjust the driver to init the PHY control register as needed. This fixes not working link detection and tftp transfers.
Good grief... kind of obnoxious how much is changed seemingly arbitrarily. Hmm. Not friendly to software.
Quoted 83 lines
Signed-off-by Anatolij Gustschin <[email protected]>--- drivers/net/phy/mv88e61xx.c | 20 +++++++++++++------- 1 file changed, 13 insertions(+), 7 deletions(-)drivers/net/phy/mv88e61xx.c +13
-8@@ -119,16 +119,12 @@#define SERDES_REG_CTRL_1_FORCE_LINK BIT(10) -#define PHY_REG_CTRL1_ENERGY_DET_SHIFT 8 -#define PHY_REG_CTRL1_ENERGY_DET_WIDTH 2 -/* Field values */ #define PORT_REG_CTRL_PSTATE_DISABLED 0#define PORT_REG_CTRL_PSTATE_FORWARD 3#define PHY_REG_CTRL1_ENERGY_DET_OFF 0#define PHY_REG_CTRL1_ENERGY_DET_SENSE_ONLY 2 -#define PHY_REG_CTRL1_ENERGY_DET_SENSE_XMIT 3/* PHY Status Register */ #define PHY_REG_STATUS1_SPEED 0xc000@@ -194,6 +190,9 @@ struct mv88e61xx_phy_priv {u16 port_stat_link_mask;u16 port_stat_dup_mask;u8 port_stat_speed_width; +u8 phy_ctrl1_en_det_shift; +u8 phy_ctrl1_en_det_width; +u8 phy_ctrl1_en_det_sense_xmit;u8 global1;u8 global2; };@@ -841,6 +840,7 @@ static int mv88e61xx_phy_enable(struct phy_device *phydev, u8 phy)static int mv88e61xx_phy_setup (struct phy_device *phydev,u8 phy) { +struct mv88e61xx_phy_priv *priv = phydev->priv;int val;/* @@ -850,9 +850,9 @@ static int mv88e61xx_phy_setup(struct phy_device *phydev, u8 phy) val =mv88e61xx_phy_read (phydev, phy,PHY_REG_CTRL1 );if (val <0 )return val; - val =bitfield_replace (val,PHY_REG_CTRL1_ENERGY_DET_SHIFT , -PHY_REG_CTRL1_ENERGY_DET_WIDTH , -PHY_REG_CTRL1_ENERGY_DET_SENSE_XMIT ); + val =bitfield_replace (val, priv->phy_ctrl1_en_det_shift, + priv->phy_ctrl1_en_det_width, + priv->phy_ctrl1_en_det_sense_xmit); val =mv88e61xx_phy_write (phydev, phy,PHY_REG_CTRL1 , val);if (val <0 )return val;@@ -964,12 +964,18 @@ static int mv88e61xx_probe(struct phy_device *phydev) priv->port_stat_link_mask =BIT (11 ); priv->port_stat_dup_mask =BIT (10 ); priv->port_stat_speed_width =2 ; + priv->phy_ctrl1_en_det_shift =8 ; + priv->phy_ctrl1_en_det_width =2 ; + priv->phy_ctrl1_en_det_sense_xmit =3 ;break ;case PORT_SWITCH_ID_6071 : priv->port_count =7 ; priv->port_stat_link_mask =BIT (12 ); priv->port_stat_dup_mask =BIT (9 ); priv->port_stat_speed_width =1 ; + priv->phy_ctrl1_en_det_shift =14 ; + priv->phy_ctrl1_en_det_width =1 ; + priv->phy_ctrl1_en_det_sense_xmit =1 ;break ;default :free (priv); --2.17.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH v2 4/6 net: phy: mv88E61xx: add config option for mv88E6071 support
In reply to Anatolij GustschinMV88E61XX_88E6020_FAMILY option enables support for switch devices 6250/6220/6020/6070/6071.
--- drivers/net/phy/Kconfig | 7 +++++++ 1 file changed, 7 insertions(+)
drivers/net/phy/Kconfig +7 -0
@@ -50,6 +50,13 @@ config MV88E61XX_SWITCH if MV88E61XX_SWITCH +config MV88E61XX_88E6020_FAMILY + bool "Marvell MV88E6020 family support." + help + The driver supports 6172/6176/6240/6352 devices in the + default configuration. Select this option to enable support + for 6250/6220/6020/6070/6071 switches. + config MV88E61XX_CPU_PORT int "CPU Port"
Signature · 1 line
2.17.1
PATCH v2 4/6 net: phy: mv88E61xx: add config option for mv88E6071 support
Quoted 14 lines · Anatolij Gustschin
MV88E61XX_88E6020_FAMILYoption enables support for switch devices 6250/6220/6020/6070/6071.Signed-off-by Anatolij Gustschin <[email protected]>--- drivers/net/phy/Kconfig | 7 +++++++ 1 file changed, 7 insertions(+)drivers/net/phy/Kconfig +0
-0
drivers/net/phy/Kconfig config MV88E61XX_SWITCH · line 58
Quoted 9 lines
drivers/net/phy/Kconfig +6
-0@@ -50,6 +50,13 @@ config MV88E61XX_SWITCH if MV88E61XX_SWITCH +config MV88E61XX_88E6020_FAMILY + bool "Marvell MV88E6020 family support." + help + The driver supports 6172/6176/6240/6352 devices in the + default configuration. Select this option to enable support + for 6250/6220/6020/6070/6071 switches.
Is there a rhyme or reason to the model numbers here? This option seems oddly named, especially since the help doesn't have the model numbers in numerical order. Can you make it a choice instead?
E.g...
choice
prompt "MV88E61XX device selection"
default MV88E61XX_88E6172
config MV88E61XX_88E6020
bool "MV88E6020"
[ ... ]
config MV88E61XX_88E6172
bool "MV88E6172"
[ ... ]
config MV88E61XX_88E6352
bool "MV88E6352"
help
The driver supports 6172/6176/6240/6352 devices in the default configuration. Select the device to enable support for (e.g. 6020/6070/6071/6220/6250).
endchoice
Quoted 11 lines
drivers/net/phy/Kconfig +1
-1+ config MV88E61XX_CPU_PORT int "CPU Port" --2.17.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH v2 4/6 net: phy: mv88E61xx: add config option for mv88E6071 support
On Tue, 23 Jul 2019 04:26:17 +0000
Joe Hershberger joe.hershberger at ni.com wrote:
...
Quoted 10 lines
drivers/net/phy/Kconfig config MV88E61XX_SWITCH · line 58
Quoted 6 lines
drivers/net/phy/Kconfig +6
-0+config MV88E61XX_88E6020_FAMILY + bool "Marvell MV88E6020 family support." + help + The driver supports 6172/6176/6240/6352 devices in the + default configuration. Select this option to enable support + for 6250/6220/6020/6070/6071 switches.Is there a rhyme or reason to the model numbers here? This option seems oddly named, especially since the help doesn't have the model numbers in numerical order. Can you make it a choice instead?
We want to be able to use single U-Boot images which support different switches, a choice will make it not possible.
--
Anatolij
PATCH v2 4/6 net: phy: mv88E61xx: add config option for mv88E6071 support
Quoted 11 lines · Anatolij Gustschin
On Tue, 23 Jul 2019 04:26:17 +0000
Joe Hershberger joe.hershberger at ni.com wrote:
...Quoted 7 lines
Quoted 6 lines
drivers/net/phy/Kconfig +6
-0+config MV88E61XX_88E6020_FAMILY + bool "Marvell MV88E6020 family support." + help + The driver supports 6172/6176/6240/6352 devices in the + default configuration. Select this option to enable support + for 6250/6220/6020/6070/6071 switches.
Quoted 6 lines
Quoted 3 lines
Is there a rhyme or reason to the model numbers here? This option seems oddly named, especially since the help doesn't have the model numbers in numerical order. Can you make it a choice instead?
We want to be able to use single U-Boot images which support different switches, a choice will make it not possible.
I don't see how choice is any different than what you have here in that respect. You have a hard-coded selection among families. If you have a need to run the same binary on multiple switches, then this option should be removed and the pre-init should be detecting the target.
-Joe
Quoted 7 lines
--
Anatolij
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH v2 4/6 net: phy: mv88E61xx: add config option for mv88E6071 support
Quoted 17 lines · Joe Hershberger
Quoted 15 lines · Anatolij Gustschin
On Tue, 23 Jul 2019 04:26:17 +0000
Joe Hershberger joe.hershberger at ni.com wrote:
...Quoted 10 lines
drivers/net/phy/Kconfig config MV88E61XX_SWITCH · line 58
Quoted 6 lines
drivers/net/phy/Kconfig +6
-0+config MV88E61XX_88E6020_FAMILY + bool "Marvell MV88E6020 family support." + help + The driver supports 6172/6176/6240/6352 devices in the + default configuration. Select this option to enable support + for 6250/6220/6020/6070/6071 switches.Is there a rhyme or reason to the model numbers here? This option seems oddly named, especially since the help doesn't have the model numbers in numerical order. Can you make it a choice instead?
Quoted 8 lines
Quoted 2 lines
We want to be able to use single U-Boot images which support different switches, a choice will make it not possible.
I don't see how choice is any different than what you have here in that respect. You have a hard-coded selection among families. If you have a need to run the same binary on multiple switches, then this option should be removed and the pre-init should be detecting the target.
Any response here?
Quoted 10 lines
-Joe
Quoted 7 lines
--
Anatolij
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH v2 4/6 net: phy: mv88E61xx: add config option for mv88E6071 support
Hi Joe,
Quoted 21 lines · On Tue, 3 Sep 2019 22:00:08 +0000 Joe Hershberger joe.hershberger at ni.com…
Quoted 20 lines · Joe Hershberger
Quoted 17 lines · Anatolij Gustschin
On Tue, 23 Jul 2019 04:26:17 +0000
Joe Hershberger joe.hershberger at ni.com wrote:
...Quoted 10 lines
drivers/net/phy/Kconfig config MV88E61XX_SWITCH · line 58
Quoted 6 lines
drivers/net/phy/Kconfig +6
-0+config MV88E61XX_88E6020_FAMILY + bool "Marvell MV88E6020 family support." + help + The driver supports 6172/6176/6240/6352 devices in the + default configuration. Select this option to enable support + for 6250/6220/6020/6070/6071 switches.Is there a rhyme or reason to the model numbers here? This option seems oddly named, especially since the help doesn't have the model numbers in numerical order. Can you make it a choice instead?
We want to be able to use single U-Boot images which support different switches, a choice will make it not possible.
Quoted 7 lines
Quoted 5 lines
I don't see how choice is any different than what you have here in that respect. You have a hard-coded selection among families. If you have a need to run the same binary on multiple switches, then this option should be removed and the pre-init should be detecting the target.
Any response here?
Sorry for delay, I've been too busy with other stuff. v4 patch series was reworked to drop this config option. Thanks!
--
Anatolij
PATCH v2 5/6 net: phy: mv88e61xx: register phy_driver struct for 88E6071
In reply to Anatolij GustschinSupport probing and init for 88E6071 switch.
--- drivers/net/phy/mv88e61xx.c | 12 ++++++++++++ 1 file changed, 12 insertions(+)
drivers/net/phy/mv88e61xx.c +12 -0
@@ -1116,10 +1116,22 @@ static struct phy_driver mv88e609x_driver = { .shutdown = &genphy_shutdown, }; +static struct phy_driver mv88e6071_driver = { + .name ="Marvell MV88E6071" , + .uid =0x1410db0 , + .mask =0xfffffff0 , + .features =PHY_BASIC_FEATURES |SUPPORTED_MII , + .probe = mv88e61xx_probe, + .config = mv88e61xx_phy_config, + .startup = mv88e61xx_phy_startup, + .shutdown = &genphy_shutdown, +}; +int phy_mv88e61xx_init (void ) {phy_register (&mv88e61xx_driver);phy_register (&mv88e609x_driver); +phy_register (&mv88e6071_driver);return 0 ; }
Signature · 1 line
2.17.1
PATCH v2 5/6 net: phy: mv88e61xx: register phy_driver struct for 88E6071
Quoted 13 lines · Anatolij Gustschin
Support probing and init for 88E6071 switch.
Signed-off-by Anatolij Gustschin <[email protected]>--- drivers/net/phy/mv88e61xx.c | 12 ++++++++++++ 1 file changed, 12 insertions(+)drivers/net/phy/mv88e61xx.c +0
-0
drivers/net/phy/mv88e61xx.c static struct phy_driver mv88e609x_driver = { · line 1120
Quoted 5 lines
drivers/net/phy/mv88e61xx.c +2
-0@@ -1116,10 +1116,22 @@ static struct phy_driver mv88e609x_driver = { .shutdown = &genphy_shutdown, }; +static struct phy_driver mv88e6071_driver = { + .name ="Marvell MV88E6071" ,
Is it really just the 6071? What about all the other ones mentioned in the Kconfig?
Quoted 24 lines
drivers/net/phy/mv88e61xx.c +10
-1+ .uid = 0x1410db0, + .mask = 0xfffffff0, + .features = PHY_BASIC_FEATURES | SUPPORTED_MII, + .probe = mv88e61xx_probe, + .config = mv88e61xx_phy_config, + .startup = mv88e61xx_phy_startup, + .shutdown = &genphy_shutdown, +}; +int phy_mv88e61xx_init (void ) {phy_register (&mv88e61xx_driver);phy_register (&mv88e609x_driver); +phy_register (&mv88e6071_driver);return 0 ; } --2.17.1
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
PATCH v2 5/6 net: phy: mv88e61xx: register phy_driver struct for 88E6071
On Tue, 23 Jul 2019 04:29:05 +0000
Joe Hershberger joe.hershberger at ni.com wrote:
...
Quoted 5 lines
drivers/net/phy/mv88e61xx.c static struct phy_driver mv88e609x_driver = { · line 1120
Quoted 2 lines
drivers/net/phy/mv88e61xx.c +2
-0+static struct phy_driver mv88e6071_driver = { + .name ="Marvell MV88E6071" ,Is it really just the 6071? What about all the other ones mentioned in the
Kconfig?
Yes, only 6071 for now. I do not have other compatible devices to get the IDs for adding them in the driver.
--
Anatolij
PATCH v2 6/6 net: phy: fix switch vendor name
In reply to Anatolij GustschinFix vendor name in MV88E61xx option description.
--- drivers/net/phy/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/phy/Kconfig +1 -1
@@ -46,7 +46,7 @@ config B53_PHY_PORTS endif # B53_SWITCH config MV88E61XX_SWITCH - bool "Marvel MV88E61xx Ethernet switch PHY support." + bool "Marvell MV88E61xx Ethernet switch PHY support." if MV88E61XX_SWITCH
Signature · 1 line
2.17.1
PATCH v2 6/6 net: phy: fix switch vendor name
Quoted 4 lines · Anatolij Gustschin
Fix vendor name in MV88E61xx option description.
Signed-off-by Anatolij Gustschin <[email protected]>
v2 cover Extend mv88e61xx driver to support 88E6071
In reply to Anatolij GustschinQuoted 8 lines · Anatolij Gustschin
This series adds support for 88E6071 switches in the mv88e61xx driver.
Changes in v2:
- fix port init for 6096/6097 devices in patch 1/6
- update commit description in patch 4/6
Quoted 8 lines
Anatolij Gustschin (6):
net: phy: mv88e61xx: rework to enable detection of 88E6071 devices
net: phy: mv88e61xx: add CPU port parameter init for 88E6071
net: phy: mv88E61xx: fixENERGY_DETinit for mv88E6071
net: phy: mv88E61xx: add config option for mv88E6071 support
net: phy: mv88e61xx: registerphy_driverstruct for 88E6071
net: phy: fix switch vendor name
For the series
And in terms of regression testing on 88E6097
v2 cover Extend mv88e61xx driver to support 88E6071
Hi Chris,
On Wed, 10 Jul 2019 21:04:42 +1200
Chris Packham judge.packham at gmail.com wrote:
...
Quoted 1 line
Tested-by Chris Packham <[email protected]>
Thanks for review and testing!
--
Anatolij