Skip to contentSkip to conversation

board: ti: beagleboneai: add initial support

PATCH Superseded Caleb Robey 2 participants 11 messages Nov 25, 2019 – Nov 26, 2019

Subsystems (3)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover board: ti: beagleboneai: add initial support

The following patches

1) Introduce the emmc based board detection for BBAI due to a lack of eeprom onboard the BBAI (to be fixed in future revision of the board).
2) Minor changes to files to support dts and bbai boot overall
3) Add structures in the pinctrl to detect the beaglebone AI and add checks for the beaglebone AI in the board detection scheme
4) Add device tree file for BeagleBone AI
5) Enable beaglebone ai in am57xx_evm_defconfig

Device tree has gone to mainline kernel found here:
https://patchwork.kernel.org/patch/11254903/

v2 Changes:
- Introduced missed additions in board.c that allow the actual configuration of the BBAI when detected. I also removed the hardcoded change of uart0 serial confirution and added a CONFIG_PREBOOT variable to do the board detect and setenv of the console variable

Caleb Robey (5):
board: ti: beagleboneai: emmc read changes
board: ti: beagleboneai: add initial support
board: ti: beagleboneai: IODELAY and pinmux changes
board: ti: beagleboneai: add dts file
board: ti: beagleboneai: enable in am57xx_evm_defconfig

 arch/arm/dts/Makefile                |   1 +
 arch/arm/dts/am5729-beagleboneai.dts | 737 +++++++++++++++++++++++++++
 arch/arm/dts/dra7.dtsi               |   2 +-
 arch/arm/mach-omap2/omap5/hw_data.c  |   1 +
 board/ti/am57xx/board.c              |  61 ++-
 board/ti/am57xx/mux_data.h           | 280 ++++++++++
 board/ti/common/board_detect.c       |  80 ++-
 board/ti/common/board_detect.h       |   9 +
 configs/am57xx_evm_defconfig         |   3 +-
 include/configs/am57xx_evm.h         |   1 -
 include/environment/ti/boot.h        |   2 +
 11 files changed, 1170 insertions(+), 7 deletions(-)
 create mode 100644 arch/arm/dts/am5729-beagleboneai.dts
Signature · 1 line
2.17.1
#1 lore raw

PATCH v2 1/5 board: ti: beagleboneai: emmc read changes

BeagleBoard.org BeagleBone AI rev A1 does not include a board identifier I2C EEPROM due to a design oversight. These boards have been put into production and are generally available now.

The board identifier information, however, has been included in the second eMMC linear boot partition (/dev/mmcblk1boot1).

This patch works by:
* First, looking for a board identifier I2C EEPROM and if not found,
* Then seeing if the boot mode matches BeagleBone AI with eMMC in the boot chain to make sure we don't enable eMMC pinmuxes on boards that don't support it, and
* Finally, initializes the eMMC pins and reading the header.

---
 board/ti/am57xx/board.c        | 37 ++++++++++++++++
 board/ti/am57xx/mux_data.h     | 16 +++++++
 board/ti/common/board_detect.c | 80 ++++++++++++++++++++++++++++++++--
 board/ti/common/board_detect.h |  9 ++++
 4 files changed, 139 insertions(+), 3 deletions(-)
board/ti/am57xx/board.c +37 -0
index 237a834c53..5fca261657 100644
@@ -12,6 +12,7 @@
 #include <palmas.h>
 #include <sata.h>
 #include <usb.h>
+#include <errno.h>
 #include <asm/omap_common.h>
 #include <asm/omap_sec_common.h>
 #include <asm/emif.h>
@@ -35,6 +36,10 @@
 #include "../common/board_detect.h"
 #include "mux_data.h"
 
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+static int board_bootmode_has_emmc(void);
+#endif
+
 #define board_is_x15()		board_ti_is("BBRDX15_")
 #define board_is_x15_revb1()	(board_ti_is("BBRDX15_") && \
 				 !strncmp("B.10", board_ti_get_rev(), 3))
@@ -505,6 +510,14 @@ void do_board_detect(void)
 				  CONFIG_EEPROM_CHIP_ADDRESS);
 	if (rc)
 		printf("ti_i2c_eeprom_init failed %d\n", rc);
+
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+	rc = board_bootmode_has_emmc();
+	if (!rc)
+		rc = ti_emmc_boardid_get();
+	if (rc)
+		printf("ti_emmc_boardid_get failed %d\n", rc);
+#endif
 }
 
 #else	/* CONFIG_SPL_BUILD */
@@ -520,6 +533,14 @@ void do_board_detect(void)
 	if (rc)
 		printf("ti_i2c_eeprom_init failed %d\n", rc);
 
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+	rc = board_bootmode_has_emmc();
+	if (!rc)
+		rc = ti_emmc_boardid_get();
+	if (rc)
+		printf("ti_emmc_boardid_get failed %d\n", rc);
+#endif
+
 	if (board_is_x15())
 		bname = "BeagleBoard X15";
 	else if (board_is_am572x_evm())
@@ -742,6 +763,11 @@ void set_muxconf_regs(void)
 {
 	do_set_mux32((*ctrl)->control_padconf_core_base,
 		     early_padconf, ARRAY_SIZE(early_padconf));
+
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+	do_set_mux32((*ctrl)->control_padconf_core_base,
+		     emmc_padconf, ARRAY_SIZE(emmc_padconf));
+#endif
 }
 
 #ifdef CONFIG_IODELAY_RECALIBRATION
@@ -1124,3 +1150,14 @@ void board_tee_image_process(ulong tee_image, size_t tee_size)
 
 U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_TEE, board_tee_image_process);
 #endif
+
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+static int board_bootmode_has_emmc(void)
+{
+	/* Check that boot mode is same as BBAI */
+	if (gd->arch.omap_boot_mode != 2)
+		return -EIO;
+
+	return 0;
+}
+#endif
board/ti/am57xx/mux_data.h +16 -0
index d4a15ae93d..2e739dec1c 100644
@@ -1000,6 +1000,22 @@ const struct pad_conf_entry early_padconf[] = {
 	{I2C1_SCL, (PIN_INPUT_PULLUP | M0)},	/* I2C1_SCL */
 };
 
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+const struct pad_conf_entry emmc_padconf[] = {
+	{GPMC_A19, (M1 | PIN_INPUT_PULLUP)},			/*  K7: gpmc_a19.mmc2_dat4 */
+	{GPMC_A20, (M1 | PIN_INPUT_PULLUP)},			/*  M7: gpmc_a20.mmc2_dat5 */
+	{GPMC_A21, (M1 | PIN_INPUT_PULLUP)},			/*  J5: gpmc_a21.mmc2_dat6 */
+	{GPMC_A22, (M1 | PIN_INPUT_PULLUP)},			/*  K6: gpmc_a22.mmc2_dat7 */
+	{GPMC_A23, (M1 | PIN_INPUT_PULLUP)},			/*  J7: gpmc_a23.mmc2_clk */
+	{GPMC_A24, (M1 | PIN_INPUT_PULLUP)},			/*  J4: gpmc_a24.mmc2_dat0 */
+	{GPMC_A25, (M1 | PIN_INPUT_PULLUP)},			/*  J6: gpmc_a25.mmc2_dat1 */
+	{GPMC_A26, (M1 | PIN_INPUT_PULLUP)},			/*  H4: gpmc_a26.mmc2_dat2 */
+	{GPMC_A27, (M1 | PIN_INPUT_PULLUP)},			/*  H5: gpmc_a27.mmc2_dat3 */
+	{GPMC_CS1, (M1 | PIN_INPUT_PULLUP)},			/*  H6: gpmc_cs1.mmc2_cmd */
+	{MCASP1_AXR5, (M14 | PIN_OUTPUT_PULLUP)},		/* F13: eMMC_RSTn (missing on schematic): mcasp1_axr5.gpio5_7 */
+};
+#endif
+
 #ifdef CONFIG_IODELAY_RECALIBRATION
 const struct iodelay_cfg_entry iodelay_cfg_array_x15_sr1_1[] = {
 	{0x0114, 2980, 0},	/* CFG_GPMC_A0_IN */
board/ti/common/board_detect.c +77 -3

101 lines not on this page · raw message

board/ti/common/board_detect.h +9 -0
index a45d8961b9..1a85b7fda9 100644
@@ -267,6 +267,15 @@ struct ti_am6_eeprom {
  */
 int ti_i2c_eeprom_am_get(int bus_addr, int dev_addr);
 
+/**
+ * ti_emmc_boardid_get() - Fetch board ID information from eMMC
+ *
+ * ep in SRAM is populated by the this function that is currently
+ * based on BeagleBone AI, but could be made more general across AM*
+ * platforms.
+ */
+int __maybe_unused ti_emmc_boardid_get(void);
+
 /**
  * ti_i2c_eeprom_dra7_get() - Consolidated eeprom data for DRA7 TI EVMs
  * @bus_addr:	I2C bus address
Signature · 1 line
2.17.1
#2 lore raw

PATCH v2 1/5 board: ti: beagleboneai: emmc read changes

Quoted 14 lines · Caleb Robey

BeagleBoard.org BeagleBone AI rev A1 does not include a board identifier I2C EEPROM due to a design oversight. These boards have been put into production and are generally available now.

The board identifier information, however, has been included in the second eMMC linear boot partition (/dev/mmcblk1boot1).

This patch works by:
* First, looking for a board identifier I2C EEPROM and if not found,
* Then seeing if the boot mode matches BeagleBone AI with eMMC in the boot chain to make sure we don't enable eMMC pinmuxes on boards that don't support it, and
* Finally, initializes the eMMC pins and reading the header.

Quoted 3 lines

Thanks and regards,
Lokesh

#3 lore raw

PATCH v2 2/5 board: ti: beagleboneai: add initial support

In reply to Caleb Robey

These are necessities for beaglebone ai boot.

---

v2 Changes:
- board.c changes that were present in previous commits were erroneously left out. Reintroduced for the sake of configuring the bbai once it is detected.

 arch/arm/mach-omap2/omap5/hw_data.c |  1 +
 board/ti/am57xx/board.c             | 24 +++++++++++++++++++++++-
 include/configs/am57xx_evm.h        |  1 -
 3 files changed, 24 insertions(+), 2 deletions(-)
arch/arm/mach-omap2/omap5/hw_data.c +1 -0
index c4a41db92a..fa4e27063c 100644
@@ -418,6 +418,7 @@ void enable_basic_clocks(void)
 		(*prcm)->cm_l3init_hsmmc2_clkctrl,
 		(*prcm)->cm_l4per_gptimer2_clkctrl,
 		(*prcm)->cm_wkup_wdtimer2_clkctrl,
+		(*prcm)->cm_l4per_uart1_clkctrl,
 		(*prcm)->cm_l4per_uart3_clkctrl,
 		(*prcm)->cm_l4per_i2c1_clkctrl,
 #ifdef CONFIG_DRIVER_TI_CPSW
board/ti/am57xx/board.c +23 -1
index 5fca261657..7d98df575d 100644
@@ -52,6 +52,7 @@ static int board_bootmode_has_emmc(void);
 #define board_is_am574x_idk()	board_ti_is("AM574IDK")
 #define board_is_am572x_idk()	board_ti_is("AM572IDK")
 #define board_is_am571x_idk()	board_ti_is("AM571IDK")
+#define board_is_bbai()		board_ti_is("BBONE-AI")
 
 #ifdef CONFIG_DRIVER_TI_CPSW
 #include <cpsw.h>
@@ -101,12 +102,19 @@ static const struct dmm_lisa_map_regs am574x_idk_lisa_regs = {
 	.is_ma_present  = 0x1
 };
 
+static const struct dmm_lisa_map_regs bbai_lisa_regs = {
+	.dmm_lisa_map_3 = 0x80640100,
+	.is_ma_present  = 0x1
+};
+
 void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs)
 {
 	if (board_is_am571x_idk())
 		*dmm_lisa_regs = &am571x_idk_lisa_regs;
 	else if (board_is_am574x_idk())
 		*dmm_lisa_regs = &am574x_idk_lisa_regs;
+	else if (board_is_bbai())
+		*dmm_lisa_regs = &bbai_lisa_regs;
 	else
 		*dmm_lisa_regs = &beagle_x15_lisa_regs;
 }
@@ -551,6 +559,8 @@ void do_board_detect(void)
 		bname = "AM572x IDK";
 	else if (board_is_am571x_idk())
 		bname = "AM571x IDK";
+	else if (board_is_bbai())
+		bname = "BeagleBone AI";
 
 	if (bname)
 		snprintf(sysinfo.board_string, SYSINFO_BOARD_NAME_MAX_LEN,
@@ -585,6 +595,8 @@ static void setup_board_eeprom_env(void)
 		name = "am572x_idk";
 	} else if (board_is_am571x_idk()) {
 		name = "am571x_idk";
+	} else if (board_is_bbai()) {
+		name = "am5729_beagleboneai";
 	} else {
 		printf("Unidentified board claims %s in eeprom header\n",
 		       board_ti_get_name());
@@ -648,7 +660,7 @@ void am57x_idk_lcd_detect(void)
 	struct udevice *dev;
 
 	/* Only valid for IDKs */
-	if (board_is_x15() || board_is_am572x_evm())
+	if (board_is_x15() || board_is_am572x_evm() || board_is_bbai())
 		return;
 
 	/* Only AM571x IDK has gpio control detect.. so check that */
@@ -746,6 +758,9 @@ int board_late_init(void)
 	/* Just probe the potentially supported cdce913 device */
 	uclass_get_device(UCLASS_CLK, 0, &dev);
 
+	if (board_is_bbai())
+		env_set("console", "ttyS0,115200n8");
+
 #if !defined(CONFIG_SPL_BUILD)
 	board_ti_set_ethaddr(2);
 #endif
@@ -793,6 +808,11 @@ void recalibrate_iodelay(void)
 		pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am571x_idk);
 		iod = iodelay_cfg_array_am571x_idk;
 		iod_sz = ARRAY_SIZE(iodelay_cfg_array_am571x_idk);
+	} else if (board_is_bbai()) {
+		pconf = core_padconf_array_essential_bbai;
+		pconf_sz = ARRAY_SIZE(core_padconf_array_essential_bbai);
+		iod = iodelay_cfg_array_bbai;
+		iod_sz = ARRAY_SIZE(iodelay_cfg_array_bbai);
 	} else {
 		/* Common for X15/GPEVM */
 		pconf = core_padconf_array_essential_x15;
@@ -1121,6 +1141,8 @@ int board_fit_config_name_match(const char *name)
 		return 0;
 	} else if (board_is_am571x_idk() && !strcmp(name, "am571x-idk")) {
 		return 0;
+	} else if (board_is_bbai() && !strcmp(name, "am5729-beagleboneai")) {
+		return 0;
 	}
 
 	return -1;
include/configs/am57xx_evm.h +0 -1
index baeca5417d..f155581fa2 100644
@@ -23,7 +23,6 @@
 
 #define CONFIG_SYS_BOOTM_LEN		SZ_64M
 
-#define CONSOLEDEV			"ttyS2"
 #define CONFIG_SYS_NS16550_COM1		UART1_BASE	/* Base EVM has UART0 */
 #define CONFIG_SYS_NS16550_COM2		UART2_BASE	/* UART2 */
 #define CONFIG_SYS_NS16550_COM3		UART3_BASE	/* UART3 */
Signature · 1 line
2.17.1
#5 lore raw

PATCH v2 3/5 board: ti: beagleboneai: IODELAY and pinmux changes

In reply to Caleb Robey

This patch configures the pinmux settings for the BeagleBone AI after the emmc read has completed.

---
 board/ti/am57xx/mux_data.h | 264 +++++++++++++++++++++++++++++++++++++
 1 file changed, 264 insertions(+)
board/ti/am57xx/mux_data.h +264 -0
index 2e739dec1c..8a216a7855 100644
@@ -233,6 +233,203 @@ const struct pad_conf_entry core_padconf_array_essential_x15[] = {
 	{RSTOUTN, (M0 | PIN_OUTPUT)},	/* rstoutn.rstoutn */
 };
 
+const struct pad_conf_entry core_padconf_array_essential_bbai[] = {
+	/* Cape Bus i2c */
+	/* NOTE: For the i2cj_scl and i2ci_scl signals to work properly, the INPUTENABLE bit of the
+	 * appropriate CTRL_CORE_PAD_x registers should be set to 0x1 because of retiming
+	 * purposes.
+	 */
+	{GPMC_A0, (M7 | PIN_INPUT_PULLUP)},			/* P9_19A: R6_GPIO7_3: gpmc_a0.i2c4_scl (Shared with F4_UART10_RTSN) */
+	{GPMC_A1, (M7 | PIN_INPUT_PULLUP)},			/* P9_20A: T9_GPIO7_4: gpmc_a1.i2c4_sda (Shared with D2_UART10_CTSN) */
+
+	/* Bluetooth UART */
+	{GPMC_A4, (M8 | PIN_INPUT)},				/* P6 UART6_RXD: gpmc_a4.uart6_rxd */
+	{GPMC_A5, (M8 | PIN_OUTPUT)},				/* R9 UART6_TXD: gpmc_a5.uart6_txd */
+	{GPMC_A6, (M8 | PIN_INPUT)},				/* R5 UART6_CTSN: gpmc_a6.uart6_ctsn */
+	{GPMC_A7, (M8 | PIN_OUTPUT)},				/* P5 UART6_RTSN: gpmc_a7.uart6_rtsn */
+
+	/* eMMC */
+	{GPMC_A19, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  K7: gpmc_a19.mmc2_dat4 */
+	{GPMC_A20, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  M7: gpmc_a20.mmc2_dat5 */
+	{GPMC_A21, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  J5: gpmc_a21.mmc2_dat6 */
+	{GPMC_A22, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  K6: gpmc_a22.mmc2_dat7 */
+	{GPMC_A23, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  J7: gpmc_a23.mmc2_clk */
+	{GPMC_A24, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  J4: gpmc_a24.mmc2_dat0 */
+	{GPMC_A25, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  J6: gpmc_a25.mmc2_dat1 */
+	{GPMC_A26, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  H4: gpmc_a26.mmc2_dat2 */
+	{GPMC_A27, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  H5: gpmc_a27.mmc2_dat3 */
+	{GPMC_CS1, (M1 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/*  H6: gpmc_cs1.mmc2_cmd */
+
+	{GPMC_ADVN_ALE, (M14 | PIN_INPUT_PULLUP)},		/* N1 RGMII_RST: gpmc_advn_ale.gpio2_23 */
+
+	{VIN1A_CLK0, (M14 | PIN_INPUT_PULLUP)},			/* AG8 INT_ADC: vin1a_clk0.gpio2_30 */
+	{VIN1A_DE0, (M10 | PIN_INPUT_PULLDOWN)},		/* P8_35B: AD9_EQEP1A_IN: vin1a_de0.eQEP1A_in */
+	{VIN1A_FLD0, (M10 | PIN_INPUT_PULLDOWN)},		/* P8_33B: AF9_EQEP1B_IN: vin1a_fld0.eQEP1B_in */
+	{VIN1A_VSYNC0, (M14 | PIN_INPUT_PULLDOWN)},		/* P9_21A: AF8_TIMER13: vin1a_vsync0.gpio3_3 */
+
+	{VIN1A_D3, (M14 | PIN_INPUT_PULLDOWN)},			/* AH6 USR4: vin1a_d3.gpio3_7 */
+
+	{VIN1A_D6, (M10 | PIN_INPUT_PULLDOWN)},			/* P8_12: AG6: vin1a_d6.eQEP2A_in */
+	{VIN1A_D7, (M10 | PIN_INPUT_PULLDOWN)},			/* P8_11: AH4: vin1a_d7.eQEP2B_in */
+	{VIN1A_D8, (M14 | PIN_INPUT_PULLDOWN)},			/* P9_15: AG4: vin1a_d8.gpio3_12 */
+	{VIN1A_D9, (M14 | PIN_INPUT)},				/* AG2 USB ID: vin1a_d9.gpio3_13 */
+	{VIN1A_D10, (M14 | PIN_INPUT_PULLDOWN)},		/* AG3 USR3: vin1a_d10.gpio3_14 */
+	{VIN1A_D11, (M14 | PIN_INPUT_PULLDOWN)},		/* AG5 USR2: vin1a_d11.gpio3_15 */
+	{VIN1A_D13, (M14 | PIN_OUTPUT_PULLDOWN)},		/* AF6 USR0: vin1a_d13.gpio3_17 */
+	{VIN1A_D14, (M14 | PIN_INPUT_PULLDOWN)},		/* AF3 WL_REG_ON: vin1a_d14.gpio3_18 */
+	{VIN1A_D16, (M14 | PIN_INPUT_PULLDOWN)},		/* AF1 BT_HOST_WAKE: vin1a_d16.gpio3_20 */
+	{VIN1A_D17, (M14 | PIN_OUTPUT_PULLDOWN)},		/* AE3 BT_WAKE: vin1a_d17.gpio3_21 */
+	{VIN1A_D18, (M14 | PIN_OUTPUT_PULLUP)},			/* AE5 BT_REG_ON: vin1a_d18.gpio3_22 */
+	{VIN1A_D19, (M14 | PIN_INPUT_PULLDOWN)},		/* AE1 WL_HOST_WAKE: vin1a_d19.gpio3_23 */
+	{VIN1A_D20, (M14 | PIN_INPUT_PULLDOWN)},		/* P9_26B: AE2: vin1a_d20.gpio3_24 */
+	{VIN1A_D23, (M14 | PIN_OUTPUT_PULLDOWN)},		/* AD3 VDD_ADC_SEL: vin1a_d23.gpio3_27 */
+
+	{VIN2A_D2, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_15A: D1: vin2a_d2.gpio4_3 */
+
+	/* Cape Bus i2c (gpio shared) */
+	{VIN2A_D4, (M14 | PIN_INPUT)},				/* P9_20B: D2_UART10_CTSN: vin2a_d4. (Shared with T9_GPIO7_4) */
+	{VIN2A_D5, (M14 | PIN_INPUT)},				/* P9_19B: F4_UART10_RTSN: vin2a_d5. (Shared with R6_GPIO7_3) */
+
+	{VIN2A_D8, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_18: F5_GPIO4_9: vin2a_d8.gpio4_9 */
+	{VIN2A_D9, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_19: E6_EHRPWM2A: vin2a_d9.gpio4_10 */
+	{VIN2A_D10, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_13: D3_EHRPWM2B: vin2a_d10.gpio4_11 */
+	{VIN2A_D12, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_14: D5_GPIO4_13: vin2a_d12.gpio4_13 */
+	{VIN2A_D13, (M10 | PIN_INPUT_PULLDOWN)},		/* P9_42B: C2_GPIO4_14: vin2a_d13.eQEP3A_in */
+	{VIN2A_D14, (M10 | PIN_INPUT_PULLDOWN)},		/* P9_27A: C3_GPIO4_15: vin2a_d14.eQEP3B_in */
+	{VIN2A_D17, (M14 | PIN_INPUT_PULLDOWN)},		/* P9_14: D6_EHRPWM3A: vin2a_d17.gpio4_25 */
+	{VIN2A_D18, (M14 | PIN_INPUT_PULLDOWN)},		/* P9_16: C5_EHRPWM3B: vin2a_d18.gpio4_26 */
+	{VIN2A_D19, (M12 | PIN_INPUT | MANUAL_MODE)},		/* P8_15B: A3_GPIO4_27: vin2a_d19.pr1_pru1_gpi16 */
+	{VIN2A_D20, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_26: B3_GPIO4_28: vin2a_d20.gpio4_28 */
+	{VIN2A_D21, (M12 | PIN_INPUT_PULLDOWN | MANUAL_MODE)},	/* P8_16: B4_GPIO4_29: vin2a_d21.pr1_pru1_gpi18 */
+	{VOUT1_CLK, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_28A: D11_VOUT1_CLK: vout1_clk.gpio4_19 */
+	{VOUT1_DE, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_30A: B10_VOUT1_DE: vout1_de.gpio4_20 */
+	{VOUT1_HSYNC, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_29A: C11_VOUT1_HSYNC: vout1_hsync.gpio4_22 */
+	{VOUT1_VSYNC, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_27A: E11_VOUT1_VSYNC: vout1_vsync.gpio4_23 */
+	{VOUT1_D0, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_45A: F11_VOUT1_D0: vout1_d0.gpio8_0 */
+	{VOUT1_D1, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_46A: G10_VOUT1_D1: vout1_d1.gpio8_1 */
+	{VOUT1_D2, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_43: F10_LCD_DATA2: vout1_d2.gpio8_2 */
+	{VOUT1_D3, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_44: G11_LCD_DATA3: vout1_d3.gpio8_3 */
+	{VOUT1_D4, (M12 | PIN_INPUT_PULLDOWN | MANUAL_MODE)},	/* P8_41: E9_LCD_DATA4: vout1_d4.pr2_pru0_gpi1 */
+	{VOUT1_D5, (M12 | PIN_INPUT_PULLDOWN | MANUAL_MODE)},	/* P8_42: F9_LCD_DATA5: vout1_d5.pr2_pru0_gpi2 */
+	{VOUT1_D6, (M12 | PIN_INPUT_PULLDOWN | MANUAL_MODE)},	/* P8_39: F8_LCD_DATA6: vout1_d6.pr2_pru0_gpi3 */
+	{VOUT1_D7, (M12 | PIN_INPUT_PULLDOWN | MANUAL_MODE)},	/* P8_40: E7_LCD_DATA7: vout1_d7.pr2_pru0_gpi4 */
+	{VOUT1_D8, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_37A: E8_VOUT1_D8: vout1_d8.gpio8_8 */
+	{VOUT1_D9, (M14 | PIN_INPUT_PULLDOWN)},			/* P8_38A: D9_VOUT1_D9: vout1_d9.gpio8_9 */
+	{VOUT1_D10, (M14 | PIN_INPUT)},				/* P8_36A: D7_VOUT1_D10: vout1_d10.gpio8_10 */
+	{VOUT1_D11, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_34A: D8_VOUT1_D11: vout1_d11.gpio8_11 */
+	{VOUT1_D14, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_31A: C8_VOUT1_D14: vout1_d14.gpio8_14 */
+	{VOUT1_D15, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_32A: C7_VOUT1_D15: vout1_d15.gpio8_15 */
+	{VOUT1_D17, (M14 | PIN_INPUT_PULLDOWN)},		/* P9_11B: B8_GPIO8_17: vout1_d17.gpio8_17 */
+	{VOUT1_D18, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_17: A7_GPIO8_18: vout1_d18.gpio8_18 */
+	{VOUT1_D19, (M12 | PIN_INPUT | MANUAL_MODE)},		/* P8_27B: A8_GPIO8_19: vout1_d19.pr2_pru0_gpi16 */
+	{VOUT1_D20, (M12 | PIN_INPUT | MANUAL_MODE)},		/* P8_28B: C9_GPIO8_20: vout1_d20.pr2_pru0_gpi17 */
+	{VOUT1_D21, (M12 | PIN_INPUT | MANUAL_MODE)},		/* P8_29B: A9_GPIO8_21: vout1_d21.pr2_pru0_gpi18 */
+	{VOUT1_D22, (M12 | PIN_INPUT | MANUAL_MODE)},		/* P8_30B: B9_GPIO8_22: vout1_d22.pr2_pru0_gpi19 */
+
+	/* Ethernet (and USB A overcurrent) */
+	{MDIO_MCLK, (M0 | PIN_OUTPUT | SLEWCONTROL)},		/* V1 MDIO_CLK: mdio_mclk.mdio_mclk */
+	{MDIO_D, (M0 | PIN_INPUT | SLEWCONTROL)},		/* U4 MDIO_D: mdio_d.mdio_d */
+	{UART3_RXD, (M14 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* V2 GPIO5_18 (USB A overcurrent): uart3_rxd.gpio5_18 */
+	{UART3_TXD, (M14 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* Y1 MII0_INT: uart3_txd.gpio5_19 */
+	{RGMII0_TXC, (M0 | PIN_OUTPUT | MANUAL_MODE)},		/* W9 RGMII0_TXC: rgmii0_txc.rgmii0_txc */
+	{RGMII0_TXCTL, (M0 | PIN_OUTPUT | MANUAL_MODE)},	/* V9 RGMII0_TXCTL: rgmii0_txctl.rgmii0_txctl */
+	{RGMII0_TXD3, (M0 | PIN_OUTPUT | MANUAL_MODE)},		/* V7 RGMII0_TXD3: rgmii0_txd3.rgmii0_txd3 */
+	{RGMII0_TXD2, (M0 | PIN_OUTPUT | MANUAL_MODE)},		/* U7 RGMII0_TXD2: rgmii0_txd2.rgmii0_txd2 */
+	{RGMII0_TXD1, (M0 | PIN_OUTPUT | MANUAL_MODE)},		/* V6 RGMII0_TXD1: rgmii0_txd1.rgmii0_txd1 */
+	{RGMII0_TXD0, (M0 | PIN_OUTPUT | MANUAL_MODE)},		/* U6 RGMII0_TXD0: rgmii0_txd0.rgmii0_txd0 */
+	{RGMII0_RXC, (M0 | PIN_INPUT | MANUAL_MODE)},		/* U5 RGMII0_RXC: rgmii0_rxc.rgmii0_rxc */
+	{RGMII0_RXCTL, (M0 | PIN_INPUT | MANUAL_MODE)},		/* V5 RGMII0_RXCTL: rgmii0_rxctl.rgmii0_rxctl */
+	{RGMII0_RXD3, (M0 | PIN_INPUT | MANUAL_MODE)},		/* V4 RGMII0_RXD3: rgmii0_rxd3.rgmii0_rxd3 */
+	{RGMII0_RXD2, (M0 | PIN_INPUT | MANUAL_MODE)},		/* V3 RGMII0_RXD2: rgmii0_rxd2.rgmii0_rxd2 */
+	{RGMII0_RXD1, (M0 | PIN_INPUT | MANUAL_MODE)},		/* Y2 RGMII0_RXD1: rgmii0_rxd1.rgmii0_rxd1 */
+	{RGMII0_RXD0, (M0 | PIN_INPUT | MANUAL_MODE)},		/* W2 RGMII0_RXD0: rgmii0_rxd0.rgmii0_rxd0 */
+
+	{USB2_DRVVBUS, (M0 | PIN_OUTPUT_PULLDOWN | SLEWCONTROL)},	/* AC10 USB2_DRVVBUS: usb2_drvvbus.usb2_drvvbus */
+
+	{GPIO6_14, (M3 | PIN_INPUT)},				/* P9_26A: E21_UART10_RXD: gpio6_14.uart10_rxd */
+	{GPIO6_15, (M0 | PIN_INPUT_PULLDOWN)},			/* P9_24: F20_UART10_TXD: gpio6_15.gpio6_15 */
+	{GPIO6_16, (M0 | PIN_INPUT_PULLUP)},			/* F21 PMIC_INT: gpio6_16.gpio6_16 */
+	{XREF_CLK0, (M14 | PIN_INPUT_PULLDOWN)},		/* P9_25: D18_GPIO6_17: xref_clk0.gpio6_17 */
+	{XREF_CLK1, (M14 | PIN_INPUT_PULLDOWN)},		/* P8_09: E17_TIMER14: xref_clk1.gpio6_18 */
+	{XREF_CLK2, (M14 | PIN_INPUT_PULLDOWN)},		/* P9_22A: B26_TIMER15: xref_clk2.gpio6_19 */
+	{XREF_CLK3, (M14 | PIN_INPUT_PULLDOWN)},		/* P9_41A: C23_CLKOUT3: xref_clk3.gpio6_20 */
+	{MCASP1_ACLKR, (M14 | PIN_INPUT_PULLDOWN)},		/* P9_12: B14_MCASP_ACLKR: mcasp1_aclkr.gpio5_0 */
+	{MCASP1_AXR0, (M10 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/* P9_18B: G12_GPIO5_2: mcasp1_axr0.i2c5_sda */
+	{MCASP1_AXR1, (M10 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/* P9_17B: F12_GPIO5_3: mcasp1_axr1.i2c5_scl */
+	{MCASP1_AXR3, (M14 | PIN_INPUT_PULLDOWN)},		/* J11 USR1: mcasp1_axr3.gpio5_5 */
+	{MCASP1_AXR5, (M14 | PIN_OUTPUT_PULLUP)},		/* F13 eMMC_RSTn (missing on schematic): mcasp1_axr5.gpio5_7 */
+	{MCASP1_AXR8, (M14 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* P9_31A: B12_SPI3_SCLK: mcasp1_axr8.gpio5_10 */
+	{MCASP1_AXR9, (M14 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* P9_29A: A11_SPI3_D1: mcasp1_axr9.gpio5_11 */
+	{MCASP1_AXR10, (M14 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* P9_30: B13_SPI3_D0: mcasp1_axr10.gpio5_12 */
+	{MCASP1_AXR11, (M14 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* P9_28: A12_SPI3_CS0: mcasp1_axr11.gpio4_17 */
+	{MCASP1_AXR12, (M14 | PIN_INPUT | SLEWCONTROL)},		/* P9_42A: E14_GPIO4_18: mcasp1_axr12.gpio4_18 */
+	{MCASP1_AXR13, (M14 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* P8_10: A13_TIMER10: mcasp1_axr13.gpio6_4 */
+	{MCASP1_AXR14, (M14 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* P8_07: G14_TIMER11: mcasp1_axr14.gpio6_5 */
+	{MCASP1_AXR15, (M14 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* P8_08: F14_TIMER12: mcasp1_axr15.gpio6_6 */
+	{MCASP3_AXR0, (M4 | PIN_INPUT | SLEWCONTROL)},			/* P9_11A: B19_UART5_RXD: mcasp3_axr0.uart5_rxd */
+
+	/* microSD Socket */
+	{MMC1_CLK, (M0 | PIN_INPUT_PULLUP)},			/*  W6: mmc1_clk.mmc1_clk */
+	{MMC1_CMD, (M0 | PIN_INPUT_PULLUP)},			/*  Y6: mmc1_cmd.mmc1_cmd */
+	{MMC1_DAT0, (M0 | PIN_INPUT_PULLUP)},			/* AA6: mmc1_dat0.mmc1_dat0 */
+	{MMC1_DAT1, (M0 | PIN_INPUT_PULLUP)},			/*  Y4: mmc1_dat1.mmc1_dat1 */
+	{MMC1_DAT2, (M0 | PIN_INPUT_PULLUP)},			/* AA5: mmc1_dat2.mmc1_dat2 */
+	{MMC1_DAT3, (M0 | PIN_INPUT_PULLUP)},			/*  Y3: mmc1_dat3.mmc1_dat3 */
+	{MMC1_SDCD, (M14 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/*  W7: mmc1_sdcd.gpio6_27 */
+
+	{MMC3_CLK, (M14 | PIN_INPUT_PULLUP)},			/* P8_21: AD4_MMC3_CLK: mmc3_clk.gpio6_29 */
+	{MMC3_CMD, (M14 | PIN_INPUT_PULLUP)},			/* P8_20: AC4_MMC3_CMD: mmc3_cmd.gpio6_30 */
+	{MMC3_DAT0, (M14 | PIN_INPUT_PULLUP)},			/* P8_25: AC7_MMC3_DATA0: mmc3_dat0.gpio6_31 */
+	{MMC3_DAT1, (M14 | PIN_INPUT_PULLUP)},			/* P8_24: AC6_MMC3_DATA1: mmc3_dat1.gpio7_0 */
+	{MMC3_DAT2, (M14 | PIN_INPUT_PULLUP)},			/* P8_05: AC9_MMC3_DATA2: mmc3_dat2.gpio7_1 */
+	{MMC3_DAT3, (M14 | PIN_INPUT_PULLUP)},			/* P8_06: AC3_MMC3_DATA3: mmc3_dat3.gpio7_2 */
+	{MMC3_DAT4, (M14 | PIN_INPUT_PULLUP)},			/* P8_23: AC8_MMC3_DATA4: mmc3_dat4.gpio1_22 */
+	{MMC3_DAT5, (M14 | PIN_INPUT_PULLUP)},			/* P8_22: AD6_MMC3_DATA5: mmc3_dat5.gpio1_23 */
+	{MMC3_DAT6, (M14 | PIN_INPUT_PULLUP)},			/* P8_03: AB8_MMC3_DATA6: mmc3_dat6.gpio1_24 */
+	{MMC3_DAT7, (M14 | PIN_INPUT_PULLUP)},			/* P8_04: AB5_MMC3_DATA7: mmc3_dat7.gpio1_25 */
+	{SPI1_CS1, (M14 | PIN_INPUT_PULLDOWN)},			/* P9_23: A22_SPI2_CS1: spi1_cs1.gpio7_11 */
+	{SPI1_CS2, (M6 | PIN_INPUT | SLEWCONTROL)},		/* B21 HDMI_DDC_HPD: spi1_cs2.hdmi1_hpd */
+	{SPI2_SCLK, (M1 | PIN_INPUT)},				/* P9_22B: A26_UART3_RXD: spi2_sclk.uart3_rxd */
+	{SPI2_D0, (M14 | PIN_INPUT | SLEWCONTROL)},		/* P9_18A: G17_SPI2_D0: spi2_d0.gpio7_16 */
+	{SPI2_CS0, (M14 | PIN_INPUT | SLEWCONTROL)},		/* P9_17A: B24_SPI2_CS0: spi2_cs0.gpio7_17 */
+	{DCAN1_TX, (M2 | PIN_INPUT | SLEWCONTROL)},		/* G20 unused: dcan1_tx.uart8_rxd */
+	{DCAN1_RX, (M6 | PIN_INPUT | SLEWCONTROL)},		/* G19 unused: dcan1_rx.hdmi1_cec */
+
+	/* BeagleBone AI: Debug UART */
+	{UART1_RXD, (M0 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* uart1_rxd.uart1_rxd */
+	{UART1_TXD, (M0 | PIN_OUTPUT_PULLDOWN | SLEWCONTROL)},	/* uart1_txd.uart1_txd */
+
+	/* WiFi MMC */
+	{UART1_CTSN, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* uart1_ctsn.mmc4_clk */
+	{UART1_RTSN, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* uart1_rtsn.mmc4_cmd */
+	{UART2_RXD, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* uart2_rxd.mmc4_dat0 */
+	{UART2_TXD, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* uart2_txd.mmc4_dat1 */
+	{UART2_CTSN, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* uart2_ctsn.mmc4_dat2 */
+	{UART2_RTSN, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* uart2_rtsn.mmc4_dat3 */
+
+	/* On-board I2C */
+	{I2C1_SDA, (M0 | PIN_INPUT_PULLUP)},	/* i2c1_sda.i2c1_sda */
+	{I2C1_SCL, (M0 | PIN_INPUT_PULLUP)},	/* i2c1_scl.i2c1_scl */
+
+	/* HDMI I2C */
+	{I2C2_SDA, (M1 | PIN_INPUT_PULLUP)},	/* i2c2_sda.hdmi1_ddc_scl */
+	{I2C2_SCL, (M1 | PIN_INPUT_PULLUP)},	/* i2c2_scl.hdmi1_ddc_sda */
+
+	{ON_OFF, (M0 | PIN_OUTPUT)},			/*  Y11: on_off.on_off */
+	{RTC_PORZ, (M0 | PIN_INPUT)},			/* AB17: rtc_porz.rtc_porz */
+	{TMS, (M0 | PIN_INPUT_PULLUP)},			/*  F18: tms.tms */
+	{TDI, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/*  D23: tdi.tdi */
+	{TDO, (M0 | PIN_OUTPUT)},			/*  F19: tdo.tdo */
+	{TCLK, (M0 | PIN_INPUT_PULLDOWN)},		/*  E20: tclk.tclk */
+	{TRSTN, (M0 | PIN_INPUT)},			/*  D20: trstn.trstn */
+	{RTCK, (M0 | PIN_OUTPUT)},			/*  E18: rtck.rtck */
+	{EMU0, (M0 | PIN_INPUT)},			/*  G21: emu0.emu0 */
+	{EMU1, (M0 | PIN_INPUT)},			/*  D24: emu1.emu1 */
+	{RESETN, (M0 | PIN_INPUT_PULLUP)},		/*  E23: resetn.resetn */
+	{NMIN_DSP, (M0 | PIN_INPUT)},			/*  D21: nmin_dsp.nmin_dsp */
+	{RSTOUTN, (M0 | PIN_OUTPUT)},			/*  F23: rstoutn.rstoutn */
+};
+
 const struct pad_conf_entry core_padconf_array_delta_x15_sr1_1[] = {
 	{MMC1_SDWP, (M14 | PIN_INPUT | SLEWCONTROL)},	/* mmc1_sdwp.gpio6_28 */
 	{VOUT1_CLK, (M0 | PIN_OUTPUT | SLEWCONTROL)},	/* vout1_clk.vout1_clk */
@@ -998,6 +1195,10 @@ const struct pad_conf_entry early_padconf[] = {
 	{UART2_RTSN, (M1 | PIN_INPUT_SLEW)},	/* uart2_rtsn.uart3_txd */
 	{I2C1_SDA, (PIN_INPUT_PULLUP | M0)},	/* I2C1_SDA */
 	{I2C1_SCL, (PIN_INPUT_PULLUP | M0)},	/* I2C1_SCL */
+
+	/* BeagleBone AI: Debug UART */
+	{UART1_RXD, (M0 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* uart1_rxd.uart1_rxd */
+	{UART1_TXD, (M0 | PIN_OUTPUT_PULLDOWN | SLEWCONTROL)},	/* uart1_txd.uart1_txd */
 };
 
 #ifdef CONFIG_SUPPORT_EMMC_BOOT
@@ -1215,6 +1416,69 @@ const struct iodelay_cfg_entry iodelay_cfg_array_x15_sr2_0[] = {
 	{0x0CEC, 2739, 0},	/* CFG_VOUT1_VSYNC_OUT */
 };
 
+const struct iodelay_cfg_entry iodelay_cfg_array_bbai[] = {
+	{0x0190, 274, 0},	/* CFG_GPMC_A19_OEN */
+	{0x0194, 162, 0},	/* CFG_GPMC_A19_OUT */
+	{0x01A8, 401, 0},	/* CFG_GPMC_A20_OEN */
+	{0x01AC, 73, 0},	/* CFG_GPMC_A20_OUT */
+	{0x01B4, 465, 0},	/* CFG_GPMC_A21_OEN */
+	{0x01B8, 115, 0},	/* CFG_GPMC_A21_OUT */
+	{0x01C0, 633, 0},	/* CFG_GPMC_A22_OEN */
+	{0x01C4, 47, 0},	/* CFG_GPMC_A22_OUT */
+	{0x01D0, 935, 280},	/* CFG_GPMC_A23_OUT */
+	{0x01D8, 621, 0},	/* CFG_GPMC_A24_OEN */
+	{0x01DC, 0, 0},		/* CFG_GPMC_A24_OUT */
+	{0x01E4, 183, 0},	/* CFG_GPMC_A25_OEN */
+	{0x01E8, 0, 0},		/* CFG_GPMC_A25_OUT */
+	{0x01F0, 467, 0},	/* CFG_GPMC_A26_OEN */
+	{0x01F4, 0, 0},		/* CFG_GPMC_A26_OUT */
+	{0x01FC, 262, 0},	/* CFG_GPMC_A27_OEN */
+	{0x0200, 46, 0},	/* CFG_GPMC_A27_OUT */
+	{0x0364, 684, 0},	/* CFG_GPMC_CS1_OEN */
+	{0x0368, 76, 0},	/* CFG_GPMC_CS1_OUT */
+	{0x06F0, 260, 0},	/* CFG_RGMII0_RXC_IN */
+	{0x06FC, 0, 1412},	/* CFG_RGMII0_RXCTL_IN */
+	{0x0708, 123, 1047},	/* CFG_RGMII0_RXD0_IN */
+	{0x0714, 139, 1081},	/* CFG_RGMII0_RXD1_IN */
+	{0x0720, 195, 1100},	/* CFG_RGMII0_RXD2_IN */
+	{0x072C, 239, 1216},	/* CFG_RGMII0_RXD3_IN */
+	{0x0740, 89, 0},	/* CFG_RGMII0_TXC_OUT */
+	{0x074C, 15, 125},	/* CFG_RGMII0_TXCTL_OUT */
+	{0x0758, 339, 162},	/* CFG_RGMII0_TXD0_OUT */
+	{0x0764, 146, 94},	/* CFG_RGMII0_TXD1_OUT */
+	{0x0770, 0, 27},	/* CFG_RGMII0_TXD2_OUT */
+	{0x077C, 291, 205},	/* CFG_RGMII0_TXD3_OUT */
+	{0x0840, 0, 0},		/* CFG_UART1_CTSN_IN */
+	{0x0848, 0, 0},		/* CFG_UART1_CTSN_OUT */
+	{0x084C, 307, 0},	/* CFG_UART1_RTSN_IN */
+	{0x0850, 0, 0},		/* CFG_UART1_RTSN_OEN */
+	{0x0854, 0, 0},		/* CFG_UART1_RTSN_OUT */
+	{0x0870, 785, 0},	/* CFG_UART2_CTSN_IN */
+	{0x0874, 0, 0},		/* CFG_UART2_CTSN_OEN */
+	{0x0878, 0, 0},		/* CFG_UART2_CTSN_OUT */
+	{0x087C, 613, 0},	/* CFG_UART2_RTSN_IN */
+	{0x0880, 0, 0},		/* CFG_UART2_RTSN_OEN */
+	{0x0884, 0, 0},		/* CFG_UART2_RTSN_OUT */
+	{0x0888, 683, 0},	/* CFG_UART2_RXD_IN */
+	{0x088C, 0, 0},		/* CFG_UART2_RXD_OEN */
+	{0x0890, 0, 0},		/* CFG_UART2_RXD_OUT */
+	{0x0894, 835, 0},	/* CFG_UART2_TXD_IN */
+	{0x0898, 0, 0},		/* CFG_UART2_TXD_OEN */
+	{0x089C, 0, 0},		/* CFG_UART2_TXD_OUT */
+	{0x0ABC, 0, 1100},	/* CFG_VIN2A_D19_IN */
+	{0x0AE0, 0, 1300},	/* CFG_VIN2A_D21_IN */
+	{0x0B1C, 0, 1000},	/* CFG_VIN2A_D4_IN */
+	{0x0B28, 0, 1700},	/* CFG_VIN2A_D5_IN */
+	{0x0C18, 0, 500},	/* CFG_VOUT1_D19_IN */
+	{0x0C30, 0, 716},	/* CFG_VOUT1_D20_IN */
+	{0x0C3C, 0, 0},		/* CFG_VOUT1_D21_IN */
+	{0x0C48, 0, 404},	/* CFG_VOUT1_D22_IN */
+	{0x0C78, 0, 0},		/* CFG_VOUT1_D4_IN */
+	{0x0C84, 0, 365},	/* CFG_VOUT1_D5_IN */
+	{0x0C90, 0, 0},		/* CFG_VOUT1_D6_IN */
+	{0x0C9C, 0, 218},	/* CFG_VOUT1_D7_IN */
+};
+
 const struct iodelay_cfg_entry iodelay_cfg_array_am574x_idk[] = {
 	{0x0114, 2199, 621},	/* CFG_GPMC_A0_IN */
 	{0x0120, 0, 0},	/* CFG_GPMC_A10_IN */
Signature · 1 line
2.17.1
#7 lore raw

PATCH v2 4/5 board: ti: beagleboneai: add dts file

In reply to Caleb Robey

From: Jason Kridner <[email protected]>

BeagleBoard.org BeagleBone AI is an open source hardware single board computer based on the Texas Instruments AM5729 SoC featuring dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4 processors, dual programmable realtime unit industrial control subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion headers.

For more information, refer to:
https://beaglebone.ai

The corresponding patch against the mainline linux kernel can be found at: https://patchwork.kernel.org/patch/11254903/

This patch introduces the BeagleBone AI device tree.

Note that the device use the "ti,tpd12s016" component which is software compatible with "ti,tpd12s015". Thus we only use the latter driver.

Due to small modifications in ocp, a tag was added to dra7.dtsi in the ocp component.

---

v2 Changes:
- Faulty "compatible" line removed and cpsw_emac0 tag moved to the correct place.

 arch/arm/dts/Makefile                |   1 +
 arch/arm/dts/am5729-beagleboneai.dts | 737 +++++++++++++++++++++++++++
 arch/arm/dts/dra7.dtsi               |   2 +-
 3 files changed, 739 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/am5729-beagleboneai.dts
arch/arm/dts/Makefile +1 -0
index d8846df1bd..e1d13f1e3a 100644
@@ -348,6 +348,7 @@ dtb-$(CONFIG_TARGET_DRA7XX_EVM) += dra72-evm.dtb dra7-evm.dtb	\
 dtb-$(CONFIG_TARGET_AM57XX_EVM) += am57xx-beagle-x15.dtb \
 	am57xx-beagle-x15-revb1.dtb \
 	am57xx-beagle-x15-revc.dtb \
+	am5729-beagleboneai.dtb \
 	am574x-idk.dtb \
 	am572x-idk.dtb	\
 	am571x-idk.dtb
arch/arm/dts/am5729-beagleboneai.dts new file +737 -0

737 lines not on this page · raw message

arch/arm/dts/dra7.dtsi +1 -1
index fd1aea0b1b..dda6951539 100644
@@ -132,7 +132,7 @@
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */
-	ocp {
+	ocp: ocp {
 		compatible = "ti,dra7-l3-noc", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
Signature · 1 line
2.17.1
#8 lore raw

PATCH v2 4/5 board: ti: beagleboneai: add dts file

Quoted 24 lines · Caleb Robey

From: Jason Kridner <[email protected]>

BeagleBoard.org BeagleBone AI is an open source hardware single board computer based on the Texas Instruments AM5729 SoC featuring dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4 processors, dual programmable realtime unit industrial control subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion headers.

For more information, refer to:
https://beaglebone.ai

The corresponding patch against the mainline linux kernel can be found at: https://patchwork.kernel.org/patch/11254903/

This patch introduces the BeagleBone AI device tree.

Note that the device use the "ti,tpd12s016" component which is software compatible with "ti,tpd12s015". Thus we only use the latter driver.

Quoted 6 lines

Due to small modifications in ocp, a tag was added to dra7.dtsi in the ocp component.

Thanks and regards,
Lokesh

#9 lore raw

PATCH v2 5/5 board: ti: beagleboneai: enable in am57xx_evm_defconfig

In reply to Caleb Robey

Adding the configurations to the evm_defconfig file

---

v2 Changes:
- addition of CONFIG_PREBOOT for console configuration
- removal of changes that hardcoded CONSOLEDEV value

 configs/am57xx_evm_defconfig  | 3 ++-
 include/environment/ti/boot.h | 2 ++
 2 files changed, 4 insertions(+), 1 deletion(-)
configs/am57xx_evm_defconfig +2 -1
index 588e58947d..8823e350f7 100644
@@ -16,6 +16,7 @@ CONFIG_SPL_LOAD_FIT=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_USE_BOOTARGS=y
 CONFIG_BOOTARGS="androidboot.serialno=${serial#} console=ttyS2,115200 androidboot.console=ttyS2 androidboot.hardware=beagle_x15board"
+CONFIG_PREBOOT="if $board_name=am5729_beaglebonai; then setenv console ttyS0,115200; fi;"
 # CONFIG_USE_BOOTCOMMAND is not set
 CONFIG_SYS_CONSOLE_INFO_QUIET=y
 # CONFIG_MISC_INIT_R is not set
@@ -38,7 +39,7 @@ CONFIG_CMD_BCB=y
 CONFIG_OF_CONTROL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="am572x-idk"
-CONFIG_OF_LIST="am57xx-beagle-x15 am57xx-beagle-x15-revb1 am57xx-beagle-x15-revc am572x-idk am571x-idk am574x-idk"
+CONFIG_OF_LIST="am57xx-beagle-x15 am57xx-beagle-x15-revb1 am57xx-beagle-x15-revc am5729-beagleboneai am572x-idk am571x-idk am574x-idk"
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
include/environment/ti/boot.h +2 -0
index 684a744f31..6313f3e328 100644
@@ -185,6 +185,8 @@
 			"setenv fdtfile am57xx-beagle-x15-revb1.dtb; fi;" \
 		"if test $board_name = beagle_x15_revc; then " \
 			"setenv fdtfile am57xx-beagle-x15-revc.dtb; fi;" \
+		"if test $board_name = am5729_beagleboneai; then " \
+			"setenv fdtfile am5729-beagleboneai.dtb; fi;" \
 		"if test $board_name = am572x_idk; then " \
 			"setenv fdtfile am572x-idk.dtb; fi;" \
 		"if test $board_name = am574x_idk; then " \
Signature · 1 line
2.17.1
#10 lore raw

PATCH v2 5/5 board: ti: beagleboneai: enable in am57xx_evm_defconfig

Quoted 4 lines · Caleb Robey

Adding the configurations to the evm_defconfig file

Thanks and regards,
Lokesh

Quoted 46 lines

---

v2 Changes:
- addition of CONFIG_PREBOOT for console configuration
- removal of changes that hardcoded CONSOLEDEV value

 configs/am57xx_evm_defconfig  | 3 ++-
 include/environment/ti/boot.h | 2 ++
 2 files changed, 4 insertions(+), 1 deletion(-)
configs/am57xx_evm_defconfig +2 -1
index 588e58947d..8823e350f7 100644
@@ -16,6 +16,7 @@ CONFIG_SPL_LOAD_FIT=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_USE_BOOTARGS=y
 CONFIG_BOOTARGS="androidboot.serialno=${serial#} console=ttyS2,115200 androidboot.console=ttyS2 androidboot.hardware=beagle_x15board"
+CONFIG_PREBOOT="if $board_name=am5729_beaglebonai; then setenv console ttyS0,115200; fi;"
 # CONFIG_USE_BOOTCOMMAND is not set
 CONFIG_SYS_CONSOLE_INFO_QUIET=y
 # CONFIG_MISC_INIT_R is not set
@@ -38,7 +39,7 @@ CONFIG_CMD_BCB=y
 CONFIG_OF_CONTROL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="am572x-idk"
-CONFIG_OF_LIST="am57xx-beagle-x15 am57xx-beagle-x15-revb1 am57xx-beagle-x15-revc am572x-idk am571x-idk am574x-idk"
+CONFIG_OF_LIST="am57xx-beagle-x15 am57xx-beagle-x15-revb1 am57xx-beagle-x15-revc am5729-beagleboneai am572x-idk am571x-idk am574x-idk"
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
include/environment/ti/boot.h +2 -0
index 684a744f31..6313f3e328 100644
@@ -185,6 +185,8 @@
 			"setenv fdtfile am57xx-beagle-x15-revb1.dtb; fi;" \
 		"if test $board_name = beagle_x15_revc; then " \
 			"setenv fdtfile am57xx-beagle-x15-revc.dtb; fi;" \
+		"if test $board_name = am5729_beagleboneai; then " \
+			"setenv fdtfile am5729-beagleboneai.dtb; fi;" \
 		"if test $board_name = am572x_idk; then " \
 			"setenv fdtfile am572x-idk.dtb; fi;" \
 		"if test $board_name = am574x_idk; then " \