sifive: fu540: Add sample SD gpt partition layout
PATCH v2 1/3 sifive: fu540: Add sample SD gpt partition layout
This is a sample GPT partition layout for SD card, right now three important partitions are added to make the system bootable.
partition layout:
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x00000821 "loader1"
attrs: 0x0000000000000000
type: 5b193300-fc78-40cd-8002-e86c45580b47
guid: cbcbef44-e627-42bc-b134-93b6f3784b8c
2 0x00000822 0x00002821 "loader2"
attrs: 0x0000000000000000
type: 2e54b353-1271-4842-806f-e436d6af6985
guid: f54eba28-d8de-4852-978d-1a673777e2ae
3 0x00002822 0x00020821 "rootfs"
attrs: 0x0000000000000004
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93Note:
- loader1 would be fsbl or spl
- loader2 would be U-Boot or U-Boot proper
---
Changes for v2:
- update the partition table
Note: On top of https://patchwork.ozlabs.org/cover/1263480/
board/sifive/fu540/Kconfig | 2 ++ include/configs/sifive-fu540.h | 13 +++++++++++++ 2 files changed, 15 insertions(+)
board/sifive/fu540/Kconfig +2 -0
@@ -32,6 +32,8 @@ config BOARD_SPECIFIC_OPTIONS # dummy imply CMD_EXT4 imply CMD_FAT imply CMD_FS_GENERIC + imply CMD_GPT + imply PARTITION_TYPE_GUID imply CMD_NET imply CMD_PING imply CLK_SIFIVE
include/configs/sifive-fu540.h +13 -0
@@ -47,6 +47,15 @@#include <config_distro_bootcmd.h> +#define TYPE_GUID_LOADER1 "5B193300-FC78-40CD-8002-E86C45580B47" +#define TYPE_GUID_LOADER2 "2E54B353-1271-4842-806F-E436D6AF6985" +#define TYPE_GUID_SYSTEM "0FC63DAF-8483-4772-8E79-3D69D8477DE4" + +#define PARTS_DEFAULT \ + "name=loader1,start=17K,size=1M,type=${type_guid_gpt_loader1};" \ + "name=loader2,size=4MB,type=${type_guid_gpt_loader2};" \ + "name=system,size=-,bootable,type=${type_guid_gpt_system};" +#define CONFIG_EXTRA_ENV_SETTINGS \ "fdt_high=0xffffffffffffffff\0" \ "initrd_high=0xffffffffffffffff\0" \
@@ -55,6 +64,10 @@"scriptaddr=0x88100000\0" \"pxefile_addr_r=0x88200000\0" \"ramdisk_addr_r=0x88300000\0" \ +"type_guid_gpt_loader1=" TYPE_GUID_LOADER1 "\0" \ +"type_guid_gpt_loader2=" TYPE_GUID_LOADER2 "\0" \ +"type_guid_gpt_system=" TYPE_GUID_SYSTEM "\0" \ +"partitions=" PARTS_DEFAULT "\0" \BOOTENV #define CONFIG_PREBOOT \
Signature · 1 line
2.17.1
PATCH v2 2/3 sifive: fu540: Add U-Boot proper sector start
Add U-Boot proper sector start offset for SiFive FU540. This value is based on the partition layout supported by SiFive FU540.
u-boot.itb need to write on this specific offset so-that the SPL will retrieve it from here and load.
---
Changes for v2:
- none
common/spl/Kconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
common/spl/Kconfig +2 -1
@@ -308,7 +308,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR ARCH_MX6 || ARCH_MX7 || \ ARCH_ROCKCHIP || ARCH_MVEBU || ARCH_SOCFPGA || \ ARCH_AT91 || ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || \ - OMAP44XX || OMAP54XX || AM33XX || AM43XX + OMAP44XX || OMAP54XX || AM33XX || AM43XX || TARGET_SIFIVE_FU540 help Use sector number for specifying U-Boot location on MMC/SD in raw mode.
@@ -325,6 +325,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || OMAP44XX || \ OMAP54XX || AM33XX || AM43XX || ARCH_K3 default 0x4000 if ARCH_ROCKCHIP + default 0x822 if TARGET_SIFIVE_FU540 help Address on the MMC to load U-Boot from, when the MMC is being used in raw mode. Units: MMC sectors (1 sector = 512 bytes).
Signature · 1 line
2.17.1
PATCH v2 3/3 doc: sifive: fu540: Document Boot from MMC
In reply to Jagan TekiDocument the Booting from MMC steps.
Detailed information about partitioning, flashing and etc.
---
Changes for v2:
- new patch
doc/board/sifive/fu540.rst | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
doc/board/sifive/fu540.rst +28 -0
@@ -363,3 +363,31 @@ load uImage. Please press Enter to activate this console. / # + +Booting from MMC +---------------- + +Use steps from "Building" section for building the U-Boot + +Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch) + +.. code-block:: none + + # sudo sgdisk --clear \ + > --set-alignment=2 \ + > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \ + > --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \ + > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \ + > /dev/sda + +Program the SD card + +.. code-block:: none + + sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34 + sudo dd if=u-boot.itb of=/dev/sda seek=2082 + sync + +Change DIP switches MSEL[3:0] are set to 1011 + +Insert the SD card and power up the board.
Signature · 1 line
2.17.1
PATCH v2 1/3 sifive: fu540: Add sample SD gpt partition layout
In reply to Jagan TekiHi Jagan,
Quoted 92 lines
-----Original Message-----
From: Jagan Teki <[email protected]>
Sent: 20 April 2020 19:08
To: Pragnesh Patel <[email protected]>; rick at andestech.com; u- boot at lists.denx.de
Cc: bmeng.cn at gmail.com; Sagar Kadam <[email protected]>; Paul Walmsley <[email protected]>; Troy Benjegerdes <[email protected]>; palmerdabbelt at google.com; anup.patel at wdc.com; atish.patra at wdc.com; linux-
amarula at amarulasolutions.com; Jagan Teki <[email protected]>
Subject: [PATCH v2 1/3] sifive: fu540: Add sample SD gpt partition layout[External Email] Do not click links or attachments unless you recognize the sender and know the content is safe
This is a sample GPT partition layout for SD card, right now three important partitions are added to make the system bootable.
partition layout:
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
10x000000220x00000821"loader1"attrs: 0x0000000000000000 type: 5b193300-fc78-40cd-8002-e86c45580b47 guid: cbcbef44-e627-42bc-b134-93b6f3784b8c 2 0x00000822 0x00002821 "loader2" attrs: 0x0000000000000000 type: 2e54b353-1271-4842-806f-e436d6af6985 guid: f54eba28-d8de-4852-978d-1a673777e2ae 3 0x00002822 0x00020821 "rootfs" attrs: 0x0000000000000004 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93Note:
- loader1 would be fsbl or spl
- loader2 would be U-Boot or U-Boot properSigned-off-by Jagan Teki <[email protected]>---
Changes for v2:
- update the partition tableNote: On top of https://patchwork.ozlabs.org/cover/1263480/
board/sifive/fu540/Kconfig | 2 ++
include/configs/sifive-fu540.h| 13 +++++++++++++2 files changed, 15 insertions(+)board/sifive/fu540/Kconfig index renamed from board/sifive/fu540/Kconfig +0
-0
5c67aab96a..43d01bab8d100644board/sifive/fu540/Kconfig +2
-0@@ -32,6 +32,8 @@ config BOARD_SPECIFIC_OPTIONS # dummy imply CMD_EXT4 imply CMD_FAT imply CMD_FS_GENERIC + imply CMD_GPT + imply PARTITION_TYPE_GUID imply CMD_NET imply CMD_PING imply CLK_SIFIVEinclude/configs/sifive-fu540.h +1
-0@@ -47,6 +47,15 @@#include <config_distro_bootcmd.h> +#define TYPE_GUID_LOADER1 "5B193300-FC78-40CD-8002-E86C45580B47"
+#defineTYPE_GUID_LOADER2"2E54B353-1271-4842-806F-
E436D6AF6985"
+#defineTYPE_GUID_SYSTEM"0FC63DAF-8483-4772-8E79-
3D69D8477DE4"include/configs/sifive-fu540.h +6
-0+ +#define PARTS_DEFAULT \ + "name=loader1,start=17K,size=1M,type=${type_guid_gpt_loader1};" \ + "name=loader2,size=4MB,type=${type_guid_gpt_loader2};" \ + "name=system,size=-,bootable,type=${type_guid_gpt_system};" +#define CONFIG_EXTRA_ENV_SETTINGS \ "fdt_high=0xffffffffffffffff\0" \ "initrd_high=0xffffffffffffffff\0" \ @@ -55,6 +64,10 @@ "scriptaddr=0x88100000\0" \ "pxefile_addr_r=0x88200000\0" \ "ramdisk_addr_r=0x88300000\0" \
include/configs/sifive-fu540.h line 70
Quoted 4 lines
include/configs/sifive-fu540.h +4
-0+"type_guid_gpt_loader1=" TYPE_GUID_LOADER1 "\0" \ +"type_guid_gpt_loader2=" TYPE_GUID_LOADER2 "\0" \ +"type_guid_gpt_system=" TYPE_GUID_SYSTEM "\0" \ +"partitions=" PARTS_DEFAULT "\0" \
Quoted 5 lines
BOOTENV
#define
CONFIG_PREBOOT\
--
2.17.1
PATCH v2 1/3 sifive: fu540: Add sample SD gpt partition layout
In reply to Jagan TekiQuoted 34 lines · Jagan Teki
This is a sample GPT partition layout for SD card, right now three important partitions are added to make the system bootable.
partition layout:
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
10x000000220x00000821"loader1"attrs: 0x0000000000000000 type: 5b193300-fc78-40cd-8002-e86c45580b47 guid: cbcbef44-e627-42bc-b134-93b6f3784b8c 2 0x00000822 0x00002821 "loader2" attrs: 0x0000000000000000 type: 2e54b353-1271-4842-806f-e436d6af6985 guid: f54eba28-d8de-4852-978d-1a673777e2ae 3 0x00002822 0x00020821 "rootfs" attrs: 0x0000000000000004 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93Note:
- loader1 would be fsbl or spl
- loader2 would be U-Boot or U-Boot properSigned-off-by Jagan Teki <[email protected]>---
Changes for v2:
- update the partition table
Quoted 6 lines
Note: On top of https://patchwork.ozlabs.org/cover/1263480/
board/sifive/fu540/Kconfig | 2 ++ include/configs/sifive-fu540.h | 13 +++++++++++++ 2 files changed, 15 insertions(+)
PATCH v2 3/3 doc: sifive: fu540: Document Boot from MMC
In reply to Jagan TekiQuoted 5 lines · Jagan Teki
Document the Booting from MMC steps.
Detailed information about partitioning, flashing and etc.
Quoted 8 lines
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- new patchdoc/board/sifive/fu540.rst | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
PATCH v2 2/3 sifive: fu540: Add U-Boot proper sector start
In reply to Jagan TekiHi Jagan,
Quoted 30 lines · Jagan Teki
Add U-Boot proper sector start offset for SiFive FU540. This value is based on the partition layout supported by SiFive FU540.
u-boot.itb need to write on this specific offset so-that the SPL will retrieve it from here and load.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- nonecommon/spl/Kconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)common/spl/Kconfig +1
-1@@ -308,7 +308,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR ARCH_MX6 || ARCH_MX7 || \ ARCH_ROCKCHIP || ARCH_MVEBU || ARCH_SOCFPGA || \ ARCH_AT91 || ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || \ - OMAP44XX || OMAP54XX || AM33XX || AM43XX + OMAP44XX || OMAP54XX || AM33XX || AM43XX || TARGET_SIFIVE_FU540 help Use sector number for specifying U-Boot location on MMC/SD in raw mode.
common/spl/Kconfig config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
Quoted 8 lines
common/spl/Kconfig +1
-1@@ -325,6 +325,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || OMAP44XX || \ OMAP54XX || AM33XX || AM43XX || ARCH_K3 default 0x4000 if ARCH_ROCKCHIP + default 0x822 if TARGET_SIFIVE_FU540 help Address on the MMC to load U-Boot from, when the MMC is being used in raw mode. Units: MMC sectors (1 sector = 512 bytes). --
It looks my comments in v1 patch is not addressed?
Regards,
Bin
PATCH v2 2/3 sifive: fu540: Add U-Boot proper sector start
Hi Bin,
Quoted 60 lines
-----Original Message-----
From: Bin Meng <[email protected]>
Sent: 29 April 2020 19:28
To: Jagan Teki <[email protected]>
Cc: Pragnesh Patel <[email protected]>; Rick Chen <[email protected]>; U-Boot Mailing List <[email protected]>; Sagar Kadam <[email protected]>; Paul Walmsley <[email protected]>; Troy Benjegerdes <[email protected]>; Palmer Dabbelt <[email protected]>; Anup Patel <[email protected]>; Atish Patra <[email protected]>; linux-amarula <linux-
amarula at amarulasolutions.com>
Subject: Re: [PATCH v2 2/3] sifive: fu540: Add U-Boot proper sector start[External Email] Do not click links or attachments unless you recognize the sender and know the content is safe
Hi Jagan,
common/spl/Kconfig config
Quoted 20 lines · Jagan Teki
Add U-Boot proper sector start offset for SiFive FU540. This value is based on the partition layout supported by SiFive FU540.
u-boot.itb need to write on this specific offset so-that the SPL will retrieve it from here and load.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- nonecommon/spl/Kconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)common/spl/Kconfig index renamed from common/spl/Kconfig +0
-0
07eee56219..1ebb30344a100644common/spl/Kconfig +0
-0@@ -308,7 +308,7 @@ config
SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTORcommon/spl/Kconfig config SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
Quoted 3 lines
common/spl/Kconfig +0
-0ARCH_MX6 || ARCH_MX7 || \ ARCH_ROCKCHIP || ARCH_MVEBU || ARCH_SOCFPGA || \ ARCH_AT91 || ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX ||\
common/spl/Kconfig config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR · line 325
Quoted 8 lines
common/spl/Kconfig +2
-1- OMAP44XX || OMAP54XX || AM33XX || AM43XX + OMAP44XX || OMAP54XX || AM33XX || AM43XX || + TARGET_SIFIVE_FU540 help Use sector number for specifying U-Boot location on MMC/SD in raw mode.@@ -325,6 +325,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX ||OMAP44XX || \
common/spl/Kconfig config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
Quoted 5 lines
common/spl/Kconfig +1
-0OMAP54XX || AM33XX || AM43XX || ARCH_K3 default 0x4000 if ARCH_ROCKCHIP + default 0x822 if TARGET_SIFIVE_FU540 help Address on the MMC to load U-Boot from, when the MMC is being
Quoted 5 lines
used
common/spl/Kconfig config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
Quoted 2 lines
common/spl/Kconfig +0
-1in raw mode. Units: MMC sectors (1 sector = 512 bytes). --It looks my comments in v1 patch is not addressed?
@Bin Meng I did not see any comment from your side, please help me if I was wrong.
Quoted 3 lines
Regards,
Bin
PATCH v2 2/3 sifive: fu540: Add U-Boot proper sector start
In reply to Jagan TekiQuoted 53 lines
-----Original Message-----
From: Jagan Teki <[email protected]>
Sent: 20 April 2020 19:08
To: Pragnesh Patel <[email protected]>; rick at andestech.com; u- boot at lists.denx.de
Cc: bmeng.cn at gmail.com; Sagar Kadam <[email protected]>; Paul Walmsley <[email protected]>; Troy Benjegerdes <[email protected]>; palmerdabbelt at google.com; anup.patel at wdc.com; atish.patra at wdc.com; linux-
amarula at amarulasolutions.com; Jagan Teki <[email protected]>
Subject: [PATCH v2 2/3] sifive: fu540: Add U-Boot proper sector start[External Email] Do not click links or attachments unless you recognize the sender and know the content is safe
Add U-Boot proper sector start offset for SiFive FU540. This value is based on the partition layout supported by SiFive FU540.
u-boot.itb need to write on this specific offset so-that the SPL will retrieve it from here and load.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- nonecommon/spl/Kconfig | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)common/spl/Kconfig index renamed from common/spl/Kconfig +0
-0
07eee56219..1ebb30344a100644common/spl/Kconfig +0
-0@@ -308,7 +308,7 @@ config
SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTORARCH_MX6 || ARCH_MX7 || \ ARCH_ROCKCHIP || ARCH_MVEBU || ARCH_SOCFPGA || \ ARCH_AT91 || ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || \common/spl/Kconfig +3
-1- OMAP44XX || OMAP54XX || AM33XX || AM43XX + OMAP44XX || OMAP54XX || AM33XX || AM43XX || + TARGET_SIFIVE_FU540 help Use sector number for specifying U-Boot location on MMC/SD in raw mode.@@ -325,6 +325,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || OMAP44XX || \ OMAP54XX || AM33XX || AM43XX || ARCH_K3 default 0x4000 if ARCH_ROCKCHIP + default 0x822 if TARGET_SIFIVE_FU540 help Address on the MMC to load U-Boot from, when the MMC is being used
Quoted 3 lines
in raw mode. Units: MMC sectors (1 sector = 512 bytes).
--
2.17.1
PATCH v2 2/3 sifive: fu540: Add U-Boot proper sector start
In reply to Pragnesh PatelHi Pragnesh,
Quoted 63 lines · Pragnesh Patel
Hi Bin,
Quoted 60 lines
-----Original Message-----
From: Bin Meng <[email protected]>
Sent: 29 April 2020 19:28
To: Jagan Teki <[email protected]>
Cc: Pragnesh Patel <[email protected]>; Rick Chen <[email protected]>; U-Boot Mailing List <[email protected]>; Sagar Kadam <[email protected]>; Paul Walmsley <[email protected]>; Troy Benjegerdes <[email protected]>; Palmer Dabbelt <[email protected]>; Anup Patel <[email protected]>; Atish Patra <[email protected]>; linux-amarula <linux-
amarula at amarulasolutions.com>
Subject: Re: [PATCH v2 2/3] sifive: fu540: Add U-Boot proper sector start[External Email] Do not click links or attachments unless you recognize the sender and know the content is safe
Hi Jagan,
common/spl/Kconfig config
Quoted 20 lines · Jagan Teki
Add U-Boot proper sector start offset for SiFive FU540. This value is based on the partition layout supported by SiFive FU540.
u-boot.itb need to write on this specific offset so-that the SPL will retrieve it from here and load.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- nonecommon/spl/Kconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)common/spl/Kconfig index renamed from common/spl/Kconfig +0
-0
07eee56219..1ebb30344a100644common/spl/Kconfig +0
-0@@ -308,7 +308,7 @@ config
SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTORcommon/spl/Kconfig config SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
Quoted 3 lines
common/spl/Kconfig +0
-0ARCH_MX6 || ARCH_MX7 || \ ARCH_ROCKCHIP || ARCH_MVEBU || ARCH_SOCFPGA || \ ARCH_AT91 || ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX ||\
common/spl/Kconfig config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR · line 325
Quoted 8 lines
common/spl/Kconfig +2
-1- OMAP44XX || OMAP54XX || AM33XX || AM43XX + OMAP44XX || OMAP54XX || AM33XX || AM43XX || + TARGET_SIFIVE_FU540 help Use sector number for specifying U-Boot location on MMC/SD in raw mode.@@ -325,6 +325,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX ||OMAP44XX || \
Quoted 5 lines
common/spl/Kconfig +1
-0OMAP54XX || AM33XX || AM43XX || ARCH_K3 default 0x4000 if ARCH_ROCKCHIP + default 0x822 if TARGET_SIFIVE_FU540 help Address on the MMC to load U-Boot from, when the MMC is being
Quoted 7 lines
Quoted 5 lines
used
common/spl/Kconfig config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
Quoted 2 lines
common/spl/Kconfig +0
-1in raw mode. Units: MMC sectors (1 sector = 512 bytes). --It looks my comments in v1 patch is not addressed?
@Bin Meng I did not see any comment from your side, please help me if I was wrong.
Sorry, I was referring to another patch which is similar to this one:
https://lists.denx.de/pipermail/u-boot/2020-April/407627.html
Regards,
Bin
PATCH v2 3/3 doc: sifive: fu540: Document Boot from MMC
In reply to Jagan TekiHi Jagan,
Quoted 19 lines
-----Original Message-----
From: Jagan Teki <[email protected]>
Sent: 20 April 2020 19:08
To: Pragnesh Patel <[email protected]>; rick at andestech.com; u- boot at lists.denx.de
Cc: bmeng.cn at gmail.com; Sagar Kadam <[email protected]>; Paul Walmsley <[email protected]>; Troy Benjegerdes <[email protected]>; palmerdabbelt at google.com; anup.patel at wdc.com; atish.patra at wdc.com; linux-
amarula at amarulasolutions.com; Jagan Teki <[email protected]>
Subject: [PATCH v2 3/3] doc: sifive: fu540: Document Boot from MMC[External Email] Do not click links or attachments unless you recognize the sender and know the content is safe
Document the Booting from MMC steps.
Detailed information about partitioning, flashing and etc.
Quoted 8 lines
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- new patch
doc/board/sifive/fu540.rst| 28 ++++++++++++++++++++++++++++1 file changed, 28 insertions(+)
This changes is not on top of https://patchwork.ozlabs.org/project/uboot/patch/20200329170538.25449-18-pragnesh.patel at sifive.com/ this.
If you don't mind, I will incorporate your changes in my v7 series which has a complete description for FSBL and SPL.
Quoted 42 lines
doc/board/sifive/fu540.rst index renamed from doc/board/sifive/fu540.rst +0
-0
3937222c6c..691ef232e2100644doc/board/sifive/fu540.rst +14
-0@@ -363,3 +363,31 @@ load uImage. Please press Enter to activate this console. / # + +Booting from MMC +---------------- + +Use steps from "Building" section for building the U-Boot + +Format the SD card (make sure the disk has GPT, otherwise use gdisk to +switch) + +.. code-block:: none + + # sudo sgdisk --clear \ + > --set-alignment=2 \ + > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
+ > --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-
1271-4842-806F-E436D6AF6985 \
+ > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-
4772-8E79-3D69D8477DE4 \doc/board/sifive/fu540.rst +13
-1+ > /dev/sda + +Program the SD card + +.. code-block:: none + + sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34 + sudo dd if=u-boot.itb of=/dev/sda seek=2082 + sync + +Change DIP switches MSEL[3:0] are set to 1011 + +Insert the SD card and power up the board. --2.17.1
PATCH v2 3/3 doc: sifive: fu540: Document Boot from MMC
Quoted 27 lines · Pragnesh Patel
Hi Jagan,
Quoted 24 lines
-----Original Message-----
From: Jagan Teki <[email protected]>
Sent: 20 April 2020 19:08
To: Pragnesh Patel <[email protected]>; rick at andestech.com; u- boot at lists.denx.de
Cc: bmeng.cn at gmail.com; Sagar Kadam <[email protected]>; Paul Walmsley <[email protected]>; Troy Benjegerdes <[email protected]>; palmerdabbelt at google.com; anup.patel at wdc.com; atish.patra at wdc.com; linux-
amarula at amarulasolutions.com; Jagan Teki <[email protected]>
Subject: [PATCH v2 3/3] doc: sifive: fu540: Document Boot from MMC[External Email] Do not click links or attachments unless you recognize the sender and know the content is safe
Document the Booting from MMC steps.
Detailed information about partitioning, flashing and etc.
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- new patch
Quoted 8 lines
Quoted 3 lines
doc/board/sifive/fu540.rst| 28 ++++++++++++++++++++++++++++1 file changed, 28 insertions(+)This changes is not on top of https://patchwork.ozlabs.org/project/uboot/patch/20200329170538.25449-18-pragnesh.patel at sifive.com/ this.
If you don't mind, I will incorporate your changes in my v7 series which has a complete description for FSBL and SPL.
Better take it in a patch where you enable SPL MMC. and have another patch before that with existing FSBL availability. This way changes look easy to understand.
Jagan.
PATCH v2 3/3 doc: sifive: fu540: Document Boot from MMC
Hi Jagan,
Quoted 54 lines
-----Original Message-----
From: Jagan Teki <[email protected]>
Sent: 29 April 2020 21:26
To: Pragnesh Patel <[email protected]>
Cc: rick at andestech.com; u-boot at lists.denx.de; bmeng.cn at gmail.com; Sagar Kadam <[email protected]>; Paul Walmsley <[email protected]>; Troy Benjegerdes <[email protected]>; palmerdabbelt at google.com; anup.patel at wdc.com; atish.patra at wdc.com; linux-
amarula at amarulasolutions.com
Subject: Re: [PATCH v2 3/3] doc: sifive: fu540: Document Boot from MMC[External Email] Do not click links or attachments unless you recognize the sender and know the content is safe
Quoted 13 lines · Pragnesh Patel
Hi Jagan,
Quoted 10 lines
-----Original Message-----
From: Jagan Teki <[email protected]>
Sent: 20 April 2020 19:08
To: Pragnesh Patel <[email protected]>; rick at andestech.com; u- boot at lists.denx.de
Cc: bmeng.cn at gmail.com; Sagar Kadam <[email protected]>; Paul Walmsley <[email protected]>; Troy Benjegerdes <[email protected]>; palmerdabbelt at google.com; anup.patel at wdc.com; atish.patra at wdc.com; linux- amarula at amarulasolutions.com; Jagan TekiQuoted 23 lines
Quoted 9 lines
Subject: [PATCH v2 3/3] doc: sifive: fu540: Document Boot from MMC
[External Email] Do not click links or attachments unless you recognize the sender and know the content is safe
Document the Booting from MMC steps.
Detailed information about partitioning, flashing and etc.
Quoted 8 lines
Signed-off-by Jagan Teki <[email protected]>---
Changes for v2:
- new patch
doc/board/sifive/fu540.rst| 28 ++++++++++++++++++++++++++++1 file changed, 28 insertions(+)This changes is not on top of
https://patchwork.ozlabs.org/project/uboot/patch/20200329170538.25449-
18-pragnesh.patel at sifive.com/
this.
Quoted 6 lines
Quoted 1 line
If you don't mind, I will incorporate your changes in my v7 series which has a
complete description for FSBL and SPL.
Better take it in a patch where you enable SPL MMC. and have another patch before that with existing FSBL availability. This way changes look easy to understand.
Nice suggestion, I will incorporate this changes in my v7 series and also add your Signed-off-by.
Can you please drop this patch in v3.
Quoted 2 lines
Jagan.