Help to test the powerpc architecture
Hi,
I'm working in a new feature for the powerpc (64 bits little endian) architecture. Since I can't test it in a real environment, I need to emulate this arch. To do this I use qemu-ppc. My problem is that the built kernel don't boot in qemu.
To build the kernel:
make defconfig ARCH=powerpc
Then I set to NO the CONFIG_KEXEC option as I found that qemu can't boot a KEXEC kernel. And now:
make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- -j4
Finally I obtain a zImage in arch/powerpc/boot/ directory.
Before to run qemu I create a rootfs with debootstrap. Then I run qemu with the following parameters:
qemu-system-ppc -kernel /media/ubuntu/Data/linux/arch/powerpc/boot/zImage \ -append "root=/dev/sda console=ttyS0" \ -drive file=qemu_image.img,index=0,media=disk,format=raw \ --nographic
If I add the "-prom-env boot-args=-v" to the end of the last command I get the same result. The qemu always stops at this point:
Quoted 7 lines
Quoted 7 lines
=============================================================
OpenBIOS 1.1 [Dec 27 2018 23:11] Configuration device id QEMU version 1 machine id 2
CPUs: 1
Memory: 128M
UUID: 00000000-0000-0000-0000-000000000000 CPU type PowerPC,750
milliseconds isn't unique.
Welcome to OpenBIOS v1.1 built on Dec 27 2018 23:11
Quoted 3 lines
Quoted 3 lines
[ppc] Kernel already loaded (
0x01000000+0x009085d8) (initrd0x00000000+0x00000000) [ppc] Kernel command line: root=/dev/sda console=ttyS0
switching to new context:
Also, I've tried to build the kernel with a DTB embedded in the image, but not luck. The same result again.
make ps3_defconfig ARCH=powerpc
make ARCH=powerpc simpleImage.ps3 CROSS_COMPILE=powerpc-linux-gnu- -j4
I'm stuck at this point. I don't know how to configure the kernel to be able to boot with qemu. Any help to point me to the right direction will be greatly appreciated.
Thank's in advance.
Oscar Carter
_______________________________________________
Kernelnewbies mailing list
[email protected]
https://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies
Quoted 47 lines · IST Oscar Carter
Hi,
I'm working in a new feature for the powerpc (64 bits little endian) architecture. Since I can't test it in a real environment, I need to emulate this arch. To do this I use qemu-ppc. My problem is that the built kernel don't boot in qemu.
To build the kernel:
make defconfig ARCH=powerpc
Then I set to NO the
CONFIG_KEXECoption as I found that qemu can't boot a KEXEC kernel. And now:make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- -j4
Finally I obtain a zImage in
arch/powerpc/boot/directory.Before to run qemu I create a rootfs with debootstrap. Then I run qemu with the following parameters:
qemu-system-ppc -kernel /media/ubuntu/Data/linux/arch/powerpc/boot/zImage \ -append "root=/dev/sda console=ttyS0" \ -drive file=qemu_image.img,index=0,media=disk,format=raw \ --nographicIf I add the "-prom-env boot-args=-v" to the end of the last command I get
the same result. The qemu always stops at this point:
Quoted 7 lines
Quoted 7 lines
=============================================================
OpenBIOS 1.1 [Dec 27 2018 23:11] Configuration device id QEMU version 1 machine id 2
CPUs: 1
Memory: 128M
UUID: 00000000-0000-0000-0000-000000000000 CPU type PowerPC,750milliseconds isn't unique.
Welcome to OpenBIOS v1.1 built on Dec 27 2018 23:11Quoted 4 lines
Quoted 4 lines
[ppc] Kernel already loaded (
0x01000000+0x009085d8) (initrd0x00000000
+0x00000000) [ppc] Kernel command line: root=/dev/sda console=ttyS0switching to new context:
Also, I've tried to build the kernel with a DTB embedded in the image, but not luck. The same result again.
Quoted 6 lines
make
ps3_defconfigARCH=powerpc
make ARCH=powerpc simpleImage.ps3 CROSS_COMPILE=powerpc-linux-gnu- -j4I'm stuck at this point. I don't know how to configure the kernel to be able to boot with qemu. Any help to point me to the right direction will be greatly appreciated.
I used pseries_defconfig and have also used pseries_le_defconfig and have done successful boots. You should probably give the machine type in your qemu command line.
-M pseries
or whatever is the machine type is for ps3
Thanks,
Santosh
Quoted 8 lines
Thank's in advance.
Oscar Carter_______________________________________________
Kernelnewbies mailing list
[email protected]
https://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies
_______________________________________________
Kernelnewbies mailing list
[email protected]
https://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies
Quoted 11 lines · Santosh S
Quoted 9 lines · IST Oscar Carter
Hi,
I'm working in a new feature for the powerpc (64 bits little endian) architecture. Since I can't test it in a real environment, I need to emulate this arch. To do this I use qemu-ppc. My problem is that the built kernel don't boot in qemu.
To build the kernel:
I would recommend you try virtme, particularly virtme-config-kernel
[jimc@frodo build-v1]$ virtme-configkernel --help
usage: virtme-configkernel [-h] [--arch ARCHITECTURE] [--allnoconfig | --defconfig | --update]
Configure a kernel for virtme
optional arguments:
-h, --help show this help message and exit
--arch ARCHITECTURE Target architecture
Mode:
--allnoconfig Overwrite configuration with a virtme-suitable
allnoconfig (unlikely to work)
--defconfig Overwrite configuration with a virtme-suitable defconfig
--update Update existing config for virtme
Quoted 65 lines
Quoted 38 lines
make defconfig ARCH=powerpc
Then I set to NO the
CONFIG_KEXECoption as I found that qemu can't boot a KEXEC kernel. And now:make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- -j4
Finally I obtain a zImage in
arch/powerpc/boot/directory.Before to run qemu I create a rootfs with debootstrap. Then I run qemu with the following parameters:
qemu-system-ppc -kernel /media/ubuntu/Data/linux/arch/powerpc/boot/zImage \ -append "root=/dev/sda console=ttyS0" \ -drive file=qemu_image.img,index=0,media=disk,format=raw \ --nographicIf I add the "-prom-env boot-args=-v" to the end of the last command I get
the same result. The qemu always stops at this point:
Quoted 7 lines
Quoted 7 lines
=============================================================
OpenBIOS 1.1 [Dec 27 2018 23:11] Configuration device id QEMU version 1 machine id 2
CPUs: 1
Memory: 128M
UUID: 00000000-0000-0000-0000-000000000000 CPU type PowerPC,750milliseconds isn't unique.
Welcome to OpenBIOS v1.1 built on Dec 27 2018 23:11Quoted 4 lines
Quoted 4 lines
[ppc] Kernel already loaded (
0x01000000+0x009085d8) (initrd0x00000000
+0x00000000) [ppc] Kernel command line: root=/dev/sda console=ttyS0switching to new context:
Also, I've tried to build the kernel with a DTB embedded in the image, but not luck. The same result again.
Quoted 6 lines
make
ps3_defconfigARCH=powerpc
make ARCH=powerpc simpleImage.ps3 CROSS_COMPILE=powerpc-linux-gnu- -j4I'm stuck at this point. I don't know how to configure the kernel to be able to boot with qemu. Any help to point me to the right direction will be greatly appreciated.
I used
pseries_defconfigand have also usedpseries_le_defconfigand have done successful boots. You should probably give the machine type in your qemu command line.
-M pseriesor whatever is the machine type is for ps3
Thanks,
SantoshQuoted 8 lines
Thank's in advance.
Oscar Carter_______________________________________________
Kernelnewbies mailing list
[email protected]
https://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies
Quoted 4 lines
_______________________________________________
Kernelnewbies mailing list
[email protected]
https://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies
_______________________________________________
Kernelnewbies mailing list
[email protected]
https://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies