Skip to contentSkip to conversation

selinux: allow labeling before policy is loaded

PATCH In review Sasha Levin 4 participants 209 messages Sep 18, 2020 Page 1 of 2

Subsystems (40)
lore
Share & tools
lore
author maintainer
#34 lore raw

PATCH 35/206 gfs2: clean up iopen glock mess in gfs2_create_inode

In reply to Sasha Levin

From: Bob Peterson <[email protected]>

[ Upstream commit 2c47c1be51fbded1f7baa2ceaed90f97932f79be ]

Before this patch, gfs2_create_inode had a use-after-free for the iopen glock in some error paths because it did this:

	gfs2_glock_put(io_gl);
fail_gunlock2:
	if (io_gl)
		clear_bit(GLF_INODE_CREATING, &io_gl->gl_flags);

In some cases, the io_gl was used for create and only had one reference, so the glock might be freed before the clear_bit(). This patch tries to straighten it out by only jumping to the error paths where iopen is properly set, and moving the gfs2_glock_put after the clear_bit.

---
 fs/gfs2/inode.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)
fs/gfs2/inode.c +7 -6
index d968b5c5df217..a52b8b0dceeb9 100644
@@ -715,7 +715,7 @@ static int gfs2_create_inode(struct inode *dir, struct dentry *dentry,
 
 	error = gfs2_trans_begin(sdp, blocks, 0);
 	if (error)
-		goto fail_gunlock2;
+		goto fail_free_inode;
 
 	if (blocks > 1) {
 		ip->i_eattr = ip->i_no_addr + 1;
@@ -726,7 +726,7 @@ static int gfs2_create_inode(struct inode *dir, struct dentry *dentry,
 
 	error = gfs2_glock_get(sdp, ip->i_no_addr, &gfs2_iopen_glops, CREATE, &io_gl);
 	if (error)
-		goto fail_gunlock2;
+		goto fail_free_inode;
 
 	BUG_ON(test_and_set_bit(GLF_INODE_CREATING, &io_gl->gl_flags));
 
@@ -735,7 +735,6 @@ static int gfs2_create_inode(struct inode *dir, struct dentry *dentry,
 		goto fail_gunlock2;
 
 	glock_set_object(ip->i_iopen_gh.gh_gl, ip);
-	gfs2_glock_put(io_gl);
 	gfs2_set_iop(inode);
 	insert_inode_hash(inode);
 
@@ -768,6 +767,8 @@ static int gfs2_create_inode(struct inode *dir, struct dentry *dentry,
 
 	mark_inode_dirty(inode);
 	d_instantiate(dentry, inode);
+	/* After instantiate, errors should result in evict which will destroy
+	 * both inode and iopen glocks properly. */
 	if (file) {
 		file->f_mode |= FMODE_CREATED;
 		error = finish_open(file, dentry, gfs2_open_common);
@@ -775,15 +776,15 @@ static int gfs2_create_inode(struct inode *dir, struct dentry *dentry,
 	gfs2_glock_dq_uninit(ghs);
 	gfs2_glock_dq_uninit(ghs + 1);
 	clear_bit(GLF_INODE_CREATING, &io_gl->gl_flags);
+	gfs2_glock_put(io_gl);
 	return error;
 
 fail_gunlock3:
 	glock_clear_object(io_gl, ip);
 	gfs2_glock_dq_uninit(&ip->i_iopen_gh);
-	gfs2_glock_put(io_gl);
 fail_gunlock2:
-	if (io_gl)
-		clear_bit(GLF_INODE_CREATING, &io_gl->gl_flags);
+	clear_bit(GLF_INODE_CREATING, &io_gl->gl_flags);
+	gfs2_glock_put(io_gl);
 fail_free_inode:
 	if (ip->i_gl) {
 		glock_clear_object(ip->i_gl, ip);
Signature · 1 line
2.25.1
author maintainer
#47 lore raw

PATCH 48/206 sctp: move trace_sctp_probe_path into sctp_outq_sack

In reply to Sasha Levin

From: Kevin Kou <[email protected]>

[ Upstream commit f643ee295c1c63bc117fb052d4da681354d6f732 ]

The original patch bringed in the "SCTP ACK tracking trace event" feature was committed at Dec.20, 2017, it replaced jprobe usage with trace events, and bringed in two trace events, one is TRACE_EVENT(sctp_probe), another one is TRACE_EVENT(sctp_probe_path). The original patch intended to trigger the trace_sctp_probe_path in TRACE_EVENT(sctp_probe) as below code,

+TRACE_EVENT(sctp_probe,
+
+ TP_PROTO(const struct sctp_endpoint *ep,
+ const struct sctp_association *asoc,
+ struct sctp_chunk *chunk),
+
+ TP_ARGS(ep, asoc, chunk),
+
+ TP_STRUCT__entry(
+ __field(__u64, asoc)
+ __field(__u32, mark)
+ __field(__u16, bind_port)
+ __field(__u16, peer_port)
+ __field(__u32, pathmtu)
+ __field(__u32, rwnd)
+ __field(__u16, unack_data)
+ ),
+
+ TP_fast_assign(
+ struct sk_buff *skb = chunk->skb;
+
+ __entry->asoc = (unsigned long)asoc;
+ __entry->mark = skb->mark;
+ __entry->bind_port = ep->base.bind_addr.port;
+ __entry->peer_port = asoc->peer.port;
+ __entry->pathmtu = asoc->pathmtu;
+ __entry->rwnd = asoc->peer.rwnd;
+ __entry->unack_data = asoc->unack_data;
+
+ if (trace_sctp_probe_path_enabled()) {
+ struct sctp_transport *sp;
+
+ list_for_each_entry(sp, &asoc->peer.transport_addr_list,
+ transports) {
+ trace_sctp_probe_path(sp, asoc);
+ }
+ }
+ ),

But I found it did not work when I did testing, and trace_sctp_probe_path had no output, I finally found that there is trace buffer lock operation(trace_event_buffer_reserve) in include/trace/trace_events.h:

static notrace void \
trace_event_raw_event_##call(void *__data, proto) \

{									\
	struct trace_event_file *trace_file = __data;			\
	struct trace_event_data_offsets_##call __maybe_unused __data_offsets;\
	struct trace_event_buffer fbuffer;				\
	struct trace_event_raw_##call *entry;				\
	int __data_size;						\
									\
	if (trace_trigger_soft_disabled(trace_file))			\
		return;							\
									\
	__data_size = trace_event_get_offsets_##call(&__data_offsets, args); \
									\
	entry = trace_event_buffer_reserve(&fbuffer, trace_file,	\
				 sizeof(*entry) + __data_size);		\
									\
	if (!entry)							\
		return;							\
									\
	tstruct								\
									\
	{ assign; }							\
									\
	trace_event_buffer_commit(&fbuffer);				\
}

The reason caused no output of trace_sctp_probe_path is that trace_sctp_probe_path written in TP_fast_assign part of TRACE_EVENT(sctp_probe), and it will be placed( { assign; } ) after the trace_event_buffer_reserve() when compiler expands Macro,

        entry = trace_event_buffer_reserve(&fbuffer, trace_file,        \
                                 sizeof(*entry) + __data_size);         \
                                                                        \
        if (!entry)                                                     \
                return;                                                 \
                                                                        \
        tstruct                                                         \
                                                                        \
        { assign; }                                                     \

so trace_sctp_probe_path finally can not acquire trace_event_buffer and return no output, that is to say the nest of tracepoint entry function is not allowed. The function call flow is:

trace_sctp_probe()
-> trace_event_raw_event_sctp_probe()
-> lock buffer
-> trace_sctp_probe_path()
-> trace_event_raw_event_sctp_probe_path() --nested -> buffer has been locked and return no output.

This patch is to remove trace_sctp_probe_path from the TP_fast_assign part of TRACE_EVENT(sctp_probe) to avoid the nest of entry function, and trigger sctp_probe_path_trace in sctp_outq_sack.

After this patch, you can enable both events individually,

  # cd /sys/kernel/debug/tracing
  # echo 1 > events/sctp/sctp_probe/enable
  # echo 1 > events/sctp/sctp_probe_path/enable

Or, you can enable all the events under sctp.

  # echo 1 > events/sctp/enable
---
 include/trace/events/sctp.h | 9 ---------
 net/sctp/outqueue.c         | 6 ++++++
 2 files changed, 6 insertions(+), 9 deletions(-)
include/trace/events/sctp.h +0 -9
index 7475c7be165aa..d4aac34365955 100644
@@ -75,15 +75,6 @@ TRACE_EVENT(sctp_probe,
 		__entry->pathmtu = asoc->pathmtu;
 		__entry->rwnd = asoc->peer.rwnd;
 		__entry->unack_data = asoc->unack_data;
-
-		if (trace_sctp_probe_path_enabled()) {
-			struct sctp_transport *sp;
-
-			list_for_each_entry(sp, &asoc->peer.transport_addr_list,
-					    transports) {
-				trace_sctp_probe_path(sp, asoc);
-			}
-		}
 	),
 
 	TP_printk("asoc=%#llx mark=%#x bind_port=%d peer_port=%d pathmtu=%d "
net/sctp/outqueue.c +6 -0
index 7bb8e5603298d..d6e83a37a1adf 100644
@@ -51,6 +51,7 @@
 #include <net/sctp/sctp.h>
 #include <net/sctp/sm.h>
 #include <net/sctp/stream_sched.h>
+#include <trace/events/sctp.h>
 
 /* Declare internal functions here.  */
 static int sctp_acked(struct sctp_sackhdr *sack, __u32 tsn);
@@ -1257,6 +1258,11 @@ int sctp_outq_sack(struct sctp_outq *q, struct sctp_chunk *chunk)
 	/* Grab the association's destination address list. */
 	transport_list = &asoc->peer.transport_addr_list;
 
+	/* SCTP path tracepoint for congestion control debugging. */
+	list_for_each_entry(transport, transport_list, transports) {
+		trace_sctp_probe_path(transport, asoc);
+	}
+
 	sack_ctsn = ntohl(sack->cum_tsn_ack);
 	gap_ack_blocks = ntohs(sack->num_gap_ack_blocks);
 	asoc->stats.gapcnt += gap_ack_blocks;
Signature · 1 line
2.25.1
author maintainer
#115 lore raw

PATCH 114/206 KVM: PPC: Book3S HV: Treat TM-related invalid form instructions on P9 like the valid ones

In reply to Sasha Levin

From: Gustavo Romero <[email protected]>

[ Upstream commit 1dff3064c764b5a51c367b949b341d2e38972bec ]

On P9 DD2.2 due to a CPU defect some TM instructions need to be emulated by KVM. This is handled at first by the hardware raising a softpatch interrupt when certain TM instructions that need KVM assistance are executed in the guest. Althought some TM instructions per Power ISA are invalid forms they can raise a softpatch interrupt too. For instance, 'tresume.' instruction as defined in the ISA must have bit 31 set (1), but an instruction that matches 'tresume.' PO and XO opcode fields but has bit 31 not set (0), like 0x7cfe9ddc, also raises a softpatch interrupt. Similarly for 'treclaim.' and 'trechkpt.' instructions with bit 31 = 0, i.e. 0x7c00075c and 0x7c0007dc, respectively. Hence, if a code like the following is executed in the guest it will raise a softpatch interrupt just like a 'tresume.' when the TM facility is enabled ('tabort. 0' in the example is used only to enable the TM facility):

int main() { asm("tabort. 0; .long 0x7cfe9ddc;"); }

Currently in such a case KVM throws a complete trace like:

[345523.705984] WARNING: CPU: 24 PID: 64413 at arch/powerpc/kvm/book3s_hv_tm.c:211 kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.705985] Modules linked in: kvm_hv(E) xt_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp ip6table_mangle ip6table_nat

iptable_mangle iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter bridge stp llc sch_fq_codel ipmi_powernv at24 vmx_crypto ipmi_devintf ipmi_msghandler ibmpowernv uio_pdrv_genirq kvm opal_prd uio leds_powernv ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx libcrc32c xor raid6_pq raid1 raid0 multipath linear tg3 crct10dif_vpmsum crc32c_vpmsum ipr [last unloaded: kvm_hv]

[345523.706030] CPU: 24 PID: 64413 Comm: CPU 0/KVM Tainted: G        W   E     5.5.0+ #1
[345523.706031] NIP:  c0080000072cb9c0 LR: c0080000072b5e80 CTR: c0080000085c7850
[345523.706034] REGS: c000000399467680 TRAP: 0700   Tainted: G        W   E      (5.5.0+)
[345523.706034] MSR:  900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]>  CR: 24022428  XER: 00000000
[345523.706042] CFAR: c0080000072b5e7c IRQMASK: 0
                GPR00: c0080000072b5e80 c000000399467910 c0080000072db500 c000000375ccc720
                GPR04: c000000375ccc720 00000003fbec0000 0000a10395dda5a6 0000000000000000
                GPR08: 000000007cfe9ddc 7cfe9ddc000005dc 7cfe9ddc7c0005dc c0080000072cd530
                GPR12: c0080000085c7850 c0000003fffeb800 0000000000000001 00007dfb737f0000
                GPR16: c0002001edcca558 0000000000000000 0000000000000000 0000000000000001
                GPR20: c000000001b21258 c0002001edcca558 0000000000000018 0000000000000000
                GPR24: 0000000001000000 ffffffffffffffff 0000000000000001 0000000000001500
                GPR28: c0002001edcc4278 c00000037dd80000 800000050280f033 c000000375ccc720
[345523.706062] NIP [c0080000072cb9c0] kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.706065] LR [c0080000072b5e80] kvmppc_handle_exit_hv.isra.53+0x3e8/0x798 [kvm_hv]
[345523.706066] Call Trace:
[345523.706069] [c000000399467910] [c000000399467940] 0xc000000399467940 (unreliable)
[345523.706071] [c000000399467950] [c000000399467980] 0xc000000399467980
[345523.706075] [c0000003994679f0] [c0080000072bd1c4] kvmhv_run_single_vcpu+0xa1c/0xb80 [kvm_hv]
[345523.706079] [c000000399467ac0] [c0080000072bd8e0] kvmppc_vcpu_run_hv+0x5b8/0xb00 [kvm_hv]
[345523.706087] [c000000399467b90] [c0080000085c93cc] kvmppc_vcpu_run+0x34/0x48 [kvm]
[345523.706095] [c000000399467bb0] [c0080000085c582c] kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm]
[345523.706101] [c000000399467c40] [c0080000085b7498] kvm_vcpu_ioctl+0x3d0/0x7b0 [kvm]
[345523.706105] [c000000399467db0] [c0000000004adf9c] ksys_ioctl+0x13c/0x170
[345523.706107] [c000000399467e00] [c0000000004adff8] sys_ioctl+0x28/0x80
[345523.706111] [c000000399467e20] [c00000000000b278] system_call+0x5c/0x68
[345523.706112] Instruction dump:
[345523.706114] 419e0390 7f8a4840 409d0048 6d497c00 2f89075d 419e021c 6d497c00 2f8907dd
[345523.706119] 419e01c0 6d497c00 2f8905dd 419e00a4 <0fe00000> 38210040 38600000 ebc1fff0

and then treats the executed instruction as a 'nop'.

However the POWER9 User's Manual, in section "4.6.10 Book II Invalid Forms", informs that for TM instructions bit 31 is in fact ignored, thus for the TM-related invalid forms ignoring bit 31 and handling them like the valid forms is an acceptable way to handle them. POWER8 behaves the same way too.

This commit changes the handling of the cases here described by treating the TM-related invalid forms that can generate a softpatch interrupt just like their valid forms (w/ bit 31 = 1) instead of as a 'nop' and by gently reporting any other unrecognized case to the host and treating it as illegal instruction instead of throwing a trace and treating it as a 'nop'.

---
 arch/powerpc/include/asm/kvm_asm.h      |  3 +++
 arch/powerpc/kvm/book3s_hv_tm.c         | 28 ++++++++++++++++++++-----
 arch/powerpc/kvm/book3s_hv_tm_builtin.c | 16 ++++++++++++--
 3 files changed, 40 insertions(+), 7 deletions(-)
arch/powerpc/include/asm/kvm_asm.h +3 -0
index a790d5cf6ea37..684e8ae00d160 100644
@@ -163,4 +163,7 @@
 
 #define KVM_INST_FETCH_FAILED	-1
 
+/* Extract PO and XOP opcode fields */
+#define PO_XOP_OPCODE_MASK 0xfc0007fe
+
 #endif /* __POWERPC_KVM_ASM_H__ */
arch/powerpc/kvm/book3s_hv_tm.c +23 -5
index 31cd0f327c8a2..e7fd60cf97804 100644
@@ -6,6 +6,8 @@
  * published by the Free Software Foundation.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/kvm_host.h>
 
 #include <asm/kvm_ppc.h>
@@ -47,7 +49,18 @@ int kvmhv_p9_tm_emulation(struct kvm_vcpu *vcpu)
 	u64 newmsr, bescr;
 	int ra, rs;
 
-	switch (instr & 0xfc0007ff) {
+	/*
+	 * rfid, rfebb, and mtmsrd encode bit 31 = 0 since it's a reserved bit
+	 * in these instructions, so masking bit 31 out doesn't change these
+	 * instructions. For treclaim., tsr., and trechkpt. instructions if bit
+	 * 31 = 0 then they are per ISA invalid forms, however P9 UM, in section
+	 * 4.6.10 Book II Invalid Forms, informs specifically that ignoring bit
+	 * 31 is an acceptable way to handle these invalid forms that have
+	 * bit 31 = 0. Moreover, for emulation purposes both forms (w/ and wo/
+	 * bit 31 set) can generate a softpatch interrupt. Hence both forms
+	 * are handled below for these instructions so they behave the same way.
+	 */
+	switch (instr & PO_XOP_OPCODE_MASK) {
 	case PPC_INST_RFID:
 		/* XXX do we need to check for PR=0 here? */
 		newmsr = vcpu->arch.shregs.srr1;
@@ -108,7 +121,8 @@ int kvmhv_p9_tm_emulation(struct kvm_vcpu *vcpu)
 		vcpu->arch.shregs.msr = newmsr;
 		return RESUME_GUEST;
 
-	case PPC_INST_TSR:
+	/* ignore bit 31, see comment above */
+	case (PPC_INST_TSR & PO_XOP_OPCODE_MASK):
 		/* check for PR=1 and arch 2.06 bit set in PCR */
 		if ((msr & MSR_PR) && (vcpu->arch.vcore->pcr & PCR_ARCH_206)) {
 			/* generate an illegal instruction interrupt */
@@ -143,7 +157,8 @@ int kvmhv_p9_tm_emulation(struct kvm_vcpu *vcpu)
 		vcpu->arch.shregs.msr = msr;
 		return RESUME_GUEST;
 
-	case PPC_INST_TRECLAIM:
+	/* ignore bit 31, see comment above */
+	case (PPC_INST_TRECLAIM & PO_XOP_OPCODE_MASK):
 		/* check for TM disabled in the HFSCR or MSR */
 		if (!(vcpu->arch.hfscr & HFSCR_TM)) {
 			/* generate an illegal instruction interrupt */
@@ -179,7 +194,8 @@ int kvmhv_p9_tm_emulation(struct kvm_vcpu *vcpu)
 		vcpu->arch.shregs.msr &= ~MSR_TS_MASK;
 		return RESUME_GUEST;
 
-	case PPC_INST_TRECHKPT:
+	/* ignore bit 31, see comment above */
+	case (PPC_INST_TRECHKPT & PO_XOP_OPCODE_MASK):
 		/* XXX do we need to check for PR=0 here? */
 		/* check for TM disabled in the HFSCR or MSR */
 		if (!(vcpu->arch.hfscr & HFSCR_TM)) {
@@ -211,6 +227,8 @@ int kvmhv_p9_tm_emulation(struct kvm_vcpu *vcpu)
 	}
 
 	/* What should we do here? We didn't recognize the instruction */
-	WARN_ON_ONCE(1);
+	kvmppc_core_queue_program(vcpu, SRR1_PROGILL);
+	pr_warn_ratelimited("Unrecognized TM-related instruction %#x for emulation", instr);
+
 	return RESUME_GUEST;
 }
arch/powerpc/kvm/book3s_hv_tm_builtin.c +14 -2
index 3cf5863bc06e8..3c7ca2fa19597 100644
@@ -26,7 +26,18 @@ int kvmhv_p9_tm_emulation_early(struct kvm_vcpu *vcpu)
 	u64 newmsr, msr, bescr;
 	int rs;
 
-	switch (instr & 0xfc0007ff) {
+	/*
+	 * rfid, rfebb, and mtmsrd encode bit 31 = 0 since it's a reserved bit
+	 * in these instructions, so masking bit 31 out doesn't change these
+	 * instructions. For the tsr. instruction if bit 31 = 0 then it is per
+	 * ISA an invalid form, however P9 UM, in section 4.6.10 Book II Invalid
+	 * Forms, informs specifically that ignoring bit 31 is an acceptable way
+	 * to handle TM-related invalid forms that have bit 31 = 0. Moreover,
+	 * for emulation purposes both forms (w/ and wo/ bit 31 set) can
+	 * generate a softpatch interrupt. Hence both forms are handled below
+	 * for tsr. to make them behave the same way.
+	 */
+	switch (instr & PO_XOP_OPCODE_MASK) {
 	case PPC_INST_RFID:
 		/* XXX do we need to check for PR=0 here? */
 		newmsr = vcpu->arch.shregs.srr1;
@@ -76,7 +87,8 @@ int kvmhv_p9_tm_emulation_early(struct kvm_vcpu *vcpu)
 		vcpu->arch.shregs.msr = newmsr;
 		return 1;
 
-	case PPC_INST_TSR:
+	/* ignore bit 31, see comment above */
+	case (PPC_INST_TSR & PO_XOP_OPCODE_MASK):
 		/* we know the MSR has the TS field = S (0b01) here */
 		msr = vcpu->arch.shregs.msr;
 		/* check for PR=1 and arch 2.06 bit set in PCR */
Signature · 1 line
2.25.1
author maintainer
#124 lore raw

PATCH 123/206 perf cpumap: Fix snprintf overflow check

In reply to Sasha Levin

From: Christophe JAILLET <[email protected]>

[ Upstream commit d74b181a028bb5a468f0c609553eff6a8fdf4887 ]

'snprintf' returns the number of characters which would be generated for the given input.

If the returned value is *greater than* or equal to the buffer size, it means that the output has been truncated.

Fix the overflow test accordingly.

Fixes 7780c25bae59f ("perf tools: Allow ability to map cpus to nodes easily")
Fixes 92a7e1278005b ("perf cpumap: Add cpu__max_present_cpu()")
Cc Alexander Shishkin <[email protected]>
Cc Don Zickus <[email protected]>
Cc He Zhe <[email protected]>
Cc Jan Stancek <[email protected]>
Cc Jiri Olsa <[email protected]>
Cc Kan Liang <[email protected]>
Cc Mark Rutland <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Peter Zijlstra <[email protected]>
---
 tools/perf/util/cpumap.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
tools/perf/util/cpumap.c +5 -5
index f93846edc1e0d..827d844f4efb1 100644
@@ -462,7 +462,7 @@ static void set_max_cpu_num(void)
 
 	/* get the highest possible cpu number for a sparse allocation */
 	ret = snprintf(path, PATH_MAX, "%s/devices/system/cpu/possible", mnt);
-	if (ret = PATH_MAX) {
+	if (ret >= PATH_MAX) {
 		pr_err("sysfs path crossed PATH_MAX(%d) size\n", PATH_MAX);
 		goto out;
 	}
@@ -473,7 +473,7 @@ static void set_max_cpu_num(void)
 
 	/* get the highest present cpu number for a sparse allocation */
 	ret = snprintf(path, PATH_MAX, "%s/devices/system/cpu/present", mnt);
-	if (ret = PATH_MAX) {
+	if (ret >= PATH_MAX) {
 		pr_err("sysfs path crossed PATH_MAX(%d) size\n", PATH_MAX);
 		goto out;
 	}
@@ -501,7 +501,7 @@ static void set_max_node_num(void)
 
 	/* get the highest possible cpu number for a sparse allocation */
 	ret = snprintf(path, PATH_MAX, "%s/devices/system/node/possible", mnt);
-	if (ret = PATH_MAX) {
+	if (ret >= PATH_MAX) {
 		pr_err("sysfs path crossed PATH_MAX(%d) size\n", PATH_MAX);
 		goto out;
 	}
@@ -586,7 +586,7 @@ int cpu__setup_cpunode_map(void)
 		return 0;
 
 	n = snprintf(path, PATH_MAX, "%s/devices/system/node", mnt);
-	if (n = PATH_MAX) {
+	if (n >= PATH_MAX) {
 		pr_err("sysfs path crossed PATH_MAX(%d) size\n", PATH_MAX);
 		return -1;
 	}
@@ -601,7 +601,7 @@ int cpu__setup_cpunode_map(void)
 			continue;
 
 		n = snprintf(buf, PATH_MAX, "%s/%s", path, dent1->d_name);
-		if (n = PATH_MAX) {
+		if (n >= PATH_MAX) {
 			pr_err("sysfs path crossed PATH_MAX(%d) size\n", PATH_MAX);
 			continue;
 		}
Signature · 1 line
2.25.1
author maintainer
#172 lore raw

PATCH 170/206 e1000: Do not perform reset in reset_task if we are already down

In reply to Sasha Levin

From: Alexander Duyck <[email protected]>

[ Upstream commit 49ee3c2ab5234757bfb56a0b3a3cb422f427e3a3 ]

We are seeing a deadlock in e1000 down when NAPI is being disabled. Looking over the kernel function trace of the system it appears that the interface is being closed and then a reset is hitting which deadlocks the interface as the NAPI interface is already disabled.

To prevent this from happening I am disabling the reset task when __E1000_DOWN is already set. In addition code has been added so that we set the __E1000_DOWN while holding the __E1000_RESET flag in e1000_close in order to guarantee that the reset task will not run after we have started the close call.

---
 drivers/net/ethernet/intel/e1000/e1000_main.c | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)
drivers/net/ethernet/intel/e1000/e1000_main.c +14 -4
index 47b867c64b147..195108858f38f 100644
@@ -542,8 +542,13 @@ void e1000_reinit_locked(struct e1000_adapter *adapter)
 	WARN_ON(in_interrupt());
 	while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
 		msleep(1);
-	e1000_down(adapter);
-	e1000_up(adapter);
+
+	/* only run the task if not already down */
+	if (!test_bit(__E1000_DOWN, &adapter->flags)) {
+		e1000_down(adapter);
+		e1000_up(adapter);
+	}
+
 	clear_bit(__E1000_RESETTING, &adapter->flags);
 }
 
@@ -1433,10 +1438,15 @@ int e1000_close(struct net_device *netdev)
 	struct e1000_hw *hw = &adapter->hw;
 	int count = E1000_CHECK_RESET_COUNT;
 
-	while (test_bit(__E1000_RESETTING, &adapter->flags) && count--)
+	while (test_and_set_bit(__E1000_RESETTING, &adapter->flags) && count--)
 		usleep_range(10000, 20000);
 
-	WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
+	WARN_ON(count < 0);
+
+	/* signal that we're down so that the reset task will no longer run */
+	set_bit(__E1000_DOWN, &adapter->flags);
+	clear_bit(__E1000_RESETTING, &adapter->flags);
+
 	e1000_down(adapter);
 	e1000_power_down_phy(adapter);
 	e1000_free_irq(adapter);
Signature · 1 line
2.25.1
author maintainer
#2 lore raw

PATCH 3/206 dma-fence: Serialise signal enabling (dma_fence_enable_sw_signaling)

In reply to Sasha Levin

From: Chris Wilson <[email protected]>

[ Upstream commit 9c98f021e4e717ffd9948fa65340ea3ef12b7935 ]

Make dma_fence_enable_sw_signaling() behave like its dma_fence_add_callback() and dma_fence_default_wait() counterparts and perform the test to enable signaling under the fence->lock, along with the action to do so. This ensure that should an implementation be trying to flush the cb_list (by signaling) on retirement before freeing the fence, it can do so in a race-free manner.

See also 0fc89b6802ba ("dma-fence: Simply wrap dma_fence_signal_locked with dma_fence_signal").

v2: Refactor all 3 enable_signaling paths to use a common function.
v3: Don't argue, just keep the tracepoint in the existing spot.

---
 drivers/dma-buf/dma-fence.c | 78 +++++++++++++++++--------------------
 1 file changed, 35 insertions(+), 43 deletions(-)
drivers/dma-buf/dma-fence.c +35 -43
index 1551ca7df3941..8586cc05def17 100644
@@ -244,6 +244,30 @@ void dma_fence_free(struct dma_fence *fence)
 }
 EXPORT_SYMBOL(dma_fence_free);
 
+static bool __dma_fence_enable_signaling(struct dma_fence *fence)
+{
+	bool was_set;
+
+	lockdep_assert_held(fence->lock);
+
+	was_set = test_and_set_bit(DMA_FENCE_FLAG_ENABLE_SIGNAL_BIT,
+				   &fence->flags);
+
+	if (test_bit(DMA_FENCE_FLAG_SIGNALED_BIT, &fence->flags))
+		return false;
+
+	if (!was_set && fence->ops->enable_signaling) {
+		trace_dma_fence_enable_signal(fence);
+
+		if (!fence->ops->enable_signaling(fence)) {
+			dma_fence_signal_locked(fence);
+			return false;
+		}
+	}
+
+	return true;
+}
+
 /**
  * dma_fence_enable_sw_signaling - enable signaling on fence
  * @fence: the fence to enable
@@ -256,19 +280,12 @@ void dma_fence_enable_sw_signaling(struct dma_fence *fence)
 {
 	unsigned long flags;
 
-	if (!test_and_set_bit(DMA_FENCE_FLAG_ENABLE_SIGNAL_BIT,
-			      &fence->flags) &&
-	    !test_bit(DMA_FENCE_FLAG_SIGNALED_BIT, &fence->flags) &&
-	    fence->ops->enable_signaling) {
-		trace_dma_fence_enable_signal(fence);
-
-		spin_lock_irqsave(fence->lock, flags);
-
-		if (!fence->ops->enable_signaling(fence))
-			dma_fence_signal_locked(fence);
+	if (test_bit(DMA_FENCE_FLAG_SIGNALED_BIT, &fence->flags))
+		return;
 
-		spin_unlock_irqrestore(fence->lock, flags);
-	}
+	spin_lock_irqsave(fence->lock, flags);
+	__dma_fence_enable_signaling(fence);
+	spin_unlock_irqrestore(fence->lock, flags);
 }
 EXPORT_SYMBOL(dma_fence_enable_sw_signaling);
 
@@ -302,7 +319,6 @@ int dma_fence_add_callback(struct dma_fence *fence, struct dma_fence_cb *cb,
 {
 	unsigned long flags;
 	int ret = 0;
-	bool was_set;
 
 	if (WARN_ON(!fence || !func))
 		return -EINVAL;
@@ -314,25 +330,14 @@ int dma_fence_add_callback(struct dma_fence *fence, struct dma_fence_cb *cb,
 
 	spin_lock_irqsave(fence->lock, flags);
 
-	was_set = test_and_set_bit(DMA_FENCE_FLAG_ENABLE_SIGNAL_BIT,
-				   &fence->flags);
-
-	if (test_bit(DMA_FENCE_FLAG_SIGNALED_BIT, &fence->flags))
-		ret = -ENOENT;
-	else if (!was_set && fence->ops->enable_signaling) {
-		trace_dma_fence_enable_signal(fence);
-
-		if (!fence->ops->enable_signaling(fence)) {
-			dma_fence_signal_locked(fence);
-			ret = -ENOENT;
-		}
-	}
-
-	if (!ret) {
+	if (__dma_fence_enable_signaling(fence)) {
 		cb->func = func;
 		list_add_tail(&cb->node, &fence->cb_list);
-	} else
+	} else {
 		INIT_LIST_HEAD(&cb->node);
+		ret = -ENOENT;
+	}
+
 	spin_unlock_irqrestore(fence->lock, flags);
 
 	return ret;
@@ -432,7 +437,6 @@ dma_fence_default_wait(struct dma_fence *fence, bool intr, signed long timeout)
 	struct default_wait_cb cb;
 	unsigned long flags;
 	signed long ret = timeout ? timeout : 1;
-	bool was_set;
 
 	if (test_bit(DMA_FENCE_FLAG_SIGNALED_BIT, &fence->flags))
 		return ret;
@@ -444,21 +448,9 @@ dma_fence_default_wait(struct dma_fence *fence, bool intr, signed long timeout)
 		goto out;
 	}
 
-	was_set = test_and_set_bit(DMA_FENCE_FLAG_ENABLE_SIGNAL_BIT,
-				   &fence->flags);
-
-	if (test_bit(DMA_FENCE_FLAG_SIGNALED_BIT, &fence->flags))
+	if (!__dma_fence_enable_signaling(fence))
 		goto out;
 
-	if (!was_set && fence->ops->enable_signaling) {
-		trace_dma_fence_enable_signal(fence);
-
-		if (!fence->ops->enable_signaling(fence)) {
-			dma_fence_signal_locked(fence);
-			goto out;
-		}
-	}
-
 	if (!timeout) {
 		ret = 0;
 		goto out;
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#3 lore raw

PATCH 4/206 ath10k: fix array out-of-bounds access

In reply to Sasha Levin

From: Miaoqing Pan <[email protected]>

[ Upstream commit c5329b2d5b8b4e41be14d31ee8505b4f5607bf9b ]

If firmware reports rate_max > WMI_TPC_RATE_MAX(WMI_TPC_FINAL_RATE_MAX) or num_tx_chain > WMI_TPC_TX_N_CHAIN, it will cause array out-of-bounds access, so print a warning and reset to avoid memory corruption.

Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035

---
 drivers/net/wireless/ath/ath10k/debug.c |  2 +-
 drivers/net/wireless/ath/ath10k/wmi.c   | 49 ++++++++++++++++---------
 2 files changed, 32 insertions(+), 19 deletions(-)
drivers/net/wireless/ath/ath10k/debug.c +1 -1
index 0baaad90b8d18..aa333110eaba6 100644
@@ -1521,7 +1521,7 @@ static void ath10k_tpc_stats_print(struct ath10k_tpc_stats *tpc_stats,
 	*len += scnprintf(buf + *len, buf_len - *len,
 			  "No.  Preamble Rate_code ");
 
-	for (i = 0; i < WMI_TPC_TX_N_CHAIN; i++)
+	for (i = 0; i < tpc_stats->num_tx_chain; i++)
 		*len += scnprintf(buf + *len, buf_len - *len,
 				  "tpc_value%d ", i);
 
drivers/net/wireless/ath/ath10k/wmi.c +31 -18

111 lines not on this page · raw message

Signature · 7 lines
2.25.1


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author maintainer
#4 lore raw

PATCH 5/206 ath10k: fix memory leak for tpc_stats_final

In reply to Sasha Levin

From: Miaoqing Pan <[email protected]>

[ Upstream commit 486a8849843455298d49e694cca9968336ce2327 ]

The memory of ar->debug.tpc_stats_final is reallocated every debugfs reading, it should be freed in ath10k_debug_destroy() for the last allocation.

Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035

---
 drivers/net/wireless/ath/ath10k/debug.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/wireless/ath/ath10k/debug.c +1 -0
index aa333110eaba6..4e980e78ba95c 100644
@@ -2365,6 +2365,7 @@ void ath10k_debug_destroy(struct ath10k *ar)
 	ath10k_debug_fw_stats_reset(ar);
 
 	kfree(ar->debug.tpc_stats);
+	kfree(ar->debug.tpc_stats_final);
 }
 
 int ath10k_debug_register(struct ath10k *ar)
Signature · 7 lines
2.25.1


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author maintainer
#5 lore raw

PATCH 6/206 mm: fix double page fault on arm64 if PTE_AF is cleared

In reply to Sasha Levin

From: Jia He <[email protected]>

[ Upstream commit 83d116c53058d505ddef051e90ab27f57015b025 ]

When we tested pmdk unit test [1] vmmalloc_fork TEST3 on arm64 guest, there will be a double page fault in __copy_from_user_inatomic of cow_user_page.

To reproduce the bug, the cmd is as follows after you deployed everything:
make -C src/test/vmmalloc_fork/ TEST_TIME=60m check

Below call trace is from arm64 do_page_fault for debugging purpose:

[  110.016195] Call trace:
[  110.016826]  do_page_fault+0x5a4/0x690
[  110.017812]  do_mem_abort+0x50/0xb0
[  110.018726]  el1_da+0x20/0xc4
[  110.019492]  __arch_copy_from_user+0x180/0x280
[  110.020646]  do_wp_page+0xb0/0x860
[  110.021517]  __handle_mm_fault+0x994/0x1338
[  110.022606]  handle_mm_fault+0xe8/0x180
[  110.023584]  do_page_fault+0x240/0x690
[  110.024535]  do_mem_abort+0x50/0xb0
[  110.025423]  el0_da+0x20/0x24

The pte info before __copy_from_user_inatomic is (PTE_AF is cleared):
[ffff9b007000] pgd=000000023d4f8003, pud=000000023da9b003,

               pmd=000000023d4b3003, pte=360000298607bd3

As told by Catalin: "On arm64 without hardware Access Flag, copying from user will fail because the pte is old and cannot be marked young. So we always end up with zeroed page after fork() + CoW for pfn mappings. we don't always have a hardware-managed access flag on arm64."

This patch fixes it by calling pte_mkyoung. Also, the parameter is changed because vmf should be passed to cow_user_page()

Add a WARN_ON_ONCE when __copy_from_user_inatomic() returns error in case there can be some obscure use-case (by Kirill).

[1] https://github.com/pmem/pmdk/tree/master/src/test/vmmalloc_fork

---
 mm/memory.c | 104 ++++++++++++++++++++++++++++++++++++++++++++--------
 1 file changed, 89 insertions(+), 15 deletions(-)
mm/memory.c +89 -15
index bbf0cc4066c84..fcad8a0d943d3 100644
@@ -116,6 +116,18 @@ int randomize_va_space __read_mostly =
 					2;
 #endif
 
+#ifndef arch_faults_on_old_pte
+static inline bool arch_faults_on_old_pte(void)
+{
+	/*
+	 * Those arches which don't have hw access flag feature need to
+	 * implement their own helper. By default, "true" means pagefault
+	 * will be hit on old pte.
+	 */
+	return true;
+}
+#endif
+
 static int __init disable_randmaps(char *s)
 {
 	randomize_va_space = 0;
@@ -2335,32 +2347,82 @@ static inline int pte_unmap_same(struct mm_struct *mm, pmd_t *pmd,
 	return same;
 }
 
-static inline void cow_user_page(struct page *dst, struct page *src, unsigned long va, struct vm_area_struct *vma)
+static inline bool cow_user_page(struct page *dst, struct page *src,
+				 struct vm_fault *vmf)
 {
+	bool ret;
+	void *kaddr;
+	void __user *uaddr;
+	bool force_mkyoung;
+	struct vm_area_struct *vma = vmf->vma;
+	struct mm_struct *mm = vma->vm_mm;
+	unsigned long addr = vmf->address;
+
 	debug_dma_assert_idle(src);
 
+	if (likely(src)) {
+		copy_user_highpage(dst, src, addr, vma);
+		return true;
+	}
+
 	/*
 	 * If the source page was a PFN mapping, we don't have
 	 * a "struct page" for it. We do a best-effort copy by
 	 * just copying from the original user address. If that
 	 * fails, we just zero-fill it. Live with it.
 	 */
-	if (unlikely(!src)) {
-		void *kaddr = kmap_atomic(dst);
-		void __user *uaddr = (void __user *)(va & PAGE_MASK);
+	kaddr = kmap_atomic(dst);
+	uaddr = (void __user *)(addr & PAGE_MASK);
+
+	/*
+	 * On architectures with software "accessed" bits, we would
+	 * take a double page fault, so mark it accessed here.
+	 */
+	force_mkyoung = arch_faults_on_old_pte() && !pte_young(vmf->orig_pte);
+	if (force_mkyoung) {
+		pte_t entry;
+
+		vmf->pte = pte_offset_map_lock(mm, vmf->pmd, addr, &vmf->ptl);
+		if (!likely(pte_same(*vmf->pte, vmf->orig_pte))) {
+			/*
+			 * Other thread has already handled the fault
+			 * and we don't need to do anything. If it's
+			 * not the case, the fault will be triggered
+			 * again on the same address.
+			 */
+			ret = false;
+			goto pte_unlock;
+		}
 
+		entry = pte_mkyoung(vmf->orig_pte);
+		if (ptep_set_access_flags(vma, addr, vmf->pte, entry, 0))
+			update_mmu_cache(vma, addr, vmf->pte);
+	}
+
+	/*
+	 * This really shouldn't fail, because the page is there
+	 * in the page tables. But it might just be unreadable,
+	 * in which case we just give up and fill the result with
+	 * zeroes.
+	 */
+	if (__copy_from_user_inatomic(kaddr, uaddr, PAGE_SIZE)) {
 		/*
-		 * This really shouldn't fail, because the page is there
-		 * in the page tables. But it might just be unreadable,
-		 * in which case we just give up and fill the result with
-		 * zeroes.
+		 * Give a warn in case there can be some obscure
+		 * use-case
 		 */
-		if (__copy_from_user_inatomic(kaddr, uaddr, PAGE_SIZE))
-			clear_page(kaddr);
-		kunmap_atomic(kaddr);
-		flush_dcache_page(dst);
-	} else
-		copy_user_highpage(dst, src, va, vma);
+		WARN_ON_ONCE(1);
+		clear_page(kaddr);
+	}
+
+	ret = true;
+
+pte_unlock:
+	if (force_mkyoung)
+		pte_unmap_unlock(vmf->pte, vmf->ptl);
+	kunmap_atomic(kaddr);
+	flush_dcache_page(dst);
+
+	return ret;
 }
 
 static gfp_t __get_fault_gfp_mask(struct vm_area_struct *vma)
@@ -2514,7 +2576,19 @@ static vm_fault_t wp_page_copy(struct vm_fault *vmf)
 				vmf->address);
 		if (!new_page)
 			goto oom;
-		cow_user_page(new_page, old_page, vmf->address, vma);
+
+		if (!cow_user_page(new_page, old_page, vmf)) {
+			/*
+			 * COW failed, if the fault was solved by other,
+			 * it's fine. If not, userspace would re-fault on
+			 * the same address and we will handle the fault
+			 * from the second attempt.
+			 */
+			put_page(new_page);
+			if (old_page)
+				put_page(old_page);
+			return 0;
+		}
 	}
 
 	if (mem_cgroup_try_charge_delay(new_page, mm, GFP_KERNEL, &memcg, false))
Signature · 1 line
2.25.1
author maintainer
#8 lore raw

PATCH 9/206 gma/gma500: fix a memory disclosure bug due to uninitialized bytes

In reply to Sasha Levin

From: Kangjie Lu <[email protected]>

[ Upstream commit 57a25a5f754ce27da2cfa6f413cfd366f878db76 ]

best_clock is an object that may be sent out. Object clock contains uninitialized bytes that are copied to best_clock, which leads to memory disclosure and information leak.

---
 drivers/gpu/drm/gma500/cdv_intel_display.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/gpu/drm/gma500/cdv_intel_display.c +2 -0
index 17db4b4749d5a..2e8479744ca4a 100644
@@ -415,6 +415,8 @@ static bool cdv_intel_find_dp_pll(const struct gma_limit_t *limit,
 	struct gma_crtc *gma_crtc = to_gma_crtc(crtc);
 	struct gma_clock_t clock;
 
+	memset(&clock, 0, sizeof(clock));
+
 	switch (refclk) {
 	case 27000:
 		if (target < 200000) {
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#10 lore raw

PATCH 11/206 media: smiapp: Fix error handling at NVM reading

In reply to Sasha Levin

From: Sakari Ailus <[email protected]>

[ Upstream commit a5b1d5413534607b05fb34470ff62bf395f5c8d0 ]

If NVM reading failed, the device was left powered on. Fix that.

---
 drivers/media/i2c/smiapp/smiapp-core.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/media/i2c/smiapp/smiapp-core.c +2 -1
index 4731e1c72f960..0a434bdce3b3b 100644
@@ -2337,11 +2337,12 @@ smiapp_sysfs_nvm_read(struct device *dev, struct device_attribute *attr,
 		if (rval < 0) {
 			if (rval != -EBUSY && rval != -EAGAIN)
 				pm_runtime_set_active(&client->dev);
-			pm_runtime_put(&client->dev);
+			pm_runtime_put_noidle(&client->dev);
 			return -ENODEV;
 		}
 
 		if (smiapp_read_nvm(sensor, sensor->nvm)) {
+			pm_runtime_put(&client->dev);
 			dev_err(&client->dev, "nvm read failed\n");
 			return -ENODEV;
 		}
Signature · 1 line
2.25.1
author maintainer
#18 lore raw

PATCH 19/206 drm/amdgpu/powerplay: fix AVFS handling with custom powerplay table

In reply to Sasha Levin

From: Alex Deucher <[email protected]>

[ Upstream commit 53dbc27ad5a93932ff1892a8e4ef266827d74a0f ]

When a custom powerplay table is provided, we need to update the OD VDDC flag to avoid AVFS being enabled when it shouldn't be.

---
 drivers/gpu/drm/amd/powerplay/hwmgr/vega10_hwmgr.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/gpu/drm/amd/powerplay/hwmgr/vega10_hwmgr.c +7 -0
index ce459ea4ec3ad..da9e6923fa659 100644
@@ -3591,6 +3591,13 @@ static int vega10_set_power_state_tasks(struct pp_hwmgr *hwmgr,
 	PP_ASSERT_WITH_CODE(!result,
 			"Failed to upload PPtable!", return result);
 
+	/*
+	 * If a custom pp table is loaded, set DPMTABLE_OD_UPDATE_VDDC flag.
+	 * That effectively disables AVFS feature.
+	 */
+	if(hwmgr->hardcode_pp_table != NULL)
+		data->need_update_dpm_table |= DPMTABLE_OD_UPDATE_VDDC;
+
 	vega10_update_avfs(hwmgr);
 
 	data->need_update_dpm_table &= DPMTABLE_OD_UPDATE_VDDC;
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#21 lore raw

PATCH 22/206 drm/amdgpu/powerplay/smu7: fix AVFS handling with custom powerplay table

In reply to Sasha Levin

From: Alex Deucher <[email protected]>

[ Upstream commit 901245624c7812b6c95d67177bae850e783b5212 ]

When a custom powerplay table is provided, we need to update the OD VDDC flag to avoid AVFS being enabled when it shouldn't be.

---
 drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c +7 -0
index 219440bebd052..420f7d15511a7 100644
@@ -3969,6 +3969,13 @@ static int smu7_set_power_state_tasks(struct pp_hwmgr *hwmgr, const void *input)
 			"Failed to populate and upload SCLK MCLK DPM levels!",
 			result = tmp_result);
 
+	/*
+	 * If a custom pp table is loaded, set DPMTABLE_OD_UPDATE_VDDC flag.
+	 * That effectively disables AVFS feature.
+	 */
+	if (hwmgr->hardcode_pp_table != NULL)
+		data->need_update_smu7_dpm_table |= DPMTABLE_OD_UPDATE_VDDC;
+
 	tmp_result = smu7_update_avfs(hwmgr);
 	PP_ASSERT_WITH_CODE((0 == tmp_result),
 			"Failed to update avfs voltages!",
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#14 lore raw

PATCH 15/206 scsi: fnic: fix use after free

In reply to Sasha Levin

From: Pan Bian <[email protected]>

[ Upstream commit ec990306f77fd4c58c3b27cc3b3c53032d6e6670 ]

The memory chunk io_req is released by mempool_free. Accessing io_req->start_time will result in a use after free bug. The variable start_time is a backup of the timestamp. So, use start_time here to avoid use after free.

---
 drivers/scsi/fnic/fnic_scsi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/scsi/fnic/fnic_scsi.c +2 -1
index 73ffc16ec0225..b521fc7650cb9 100644
@@ -1034,7 +1034,8 @@ static void fnic_fcpio_icmnd_cmpl_handler(struct fnic *fnic,
 		atomic64_inc(&fnic_stats->io_stats.io_completions);
 
 
-	io_duration_time = jiffies_to_msecs(jiffies) - jiffies_to_msecs(io_req->start_time);
+	io_duration_time = jiffies_to_msecs(jiffies) -
+						jiffies_to_msecs(start_time);
 
 	if(io_duration_time <= 10)
 		atomic64_inc(&fnic_stats->io_stats.io_btw_0_to_10_msec);
Signature · 1 line
2.25.1
author maintainer
#29 lore raw

PATCH 30/206 fix dget_parent() fastpath race

In reply to Sasha Levin

From: Al Viro <[email protected]>

[ Upstream commit e84009336711d2bba885fc9cea66348ddfce3758 ]

We are overoptimistic about taking the fast path there; seeing the same value in ->d_parent after having grabbed a reference to that parent does *not* mean that it has remained our parent all along.

That wouldn't be a big deal (in the end it is our parent and we have grabbed the reference we are about to return), but... the situation with barriers is messed up.

We might have hit the following sequence:

d is a dentry of /tmp/a/b
CPU1: CPU2:
parent = d->d_parent (i.e. dentry of /tmp/a)
rename /tmp/a/b to /tmp/b rmdir /tmp/a, making its dentry negative
grab reference to parent,
end up with cached parent->d_inode (NULL)
mkdir /tmp/a, rename /tmp/b to /tmp/a/b
recheck d->d_parent, which is back to original
decide that everything's fine and return the reference we'd got.

The trouble is, caller (on CPU1) will observe dget_parent() returning an apparently negative dentry. It actually is positive, but CPU1 has stale ->d_inode cached.

Use d->d_seq to see if it has been moved instead of rechecking ->d_parent.
NOTE: we are *NOT* going to retry on any kind of ->d_seq mismatch; we just go into the slow path in such case. We don't wait for ->d_seq to become even either - again, if we are racing with renames, we can bloody well go to slow path anyway.

---
 fs/dcache.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
fs/dcache.c +3 -1
index 6e0022326afe3..20370a0997bf9 100644
@@ -864,17 +864,19 @@ struct dentry *dget_parent(struct dentry *dentry)
 {
 	int gotref;
 	struct dentry *ret;
+	unsigned seq;
 
 	/*
 	 * Do optimistic parent lookup without any
 	 * locking.
 	 */
 	rcu_read_lock();
+	seq = raw_seqcount_begin(&dentry->d_seq);
 	ret = READ_ONCE(dentry->d_parent);
 	gotref = lockref_get_not_zero(&ret->d_lockref);
 	rcu_read_unlock();
 	if (likely(gotref)) {
-		if (likely(ret == READ_ONCE(dentry->d_parent)))
+		if (!read_seqcount_retry(&dentry->d_seq, seq))
 			return ret;
 		dput(ret);
 	}
Signature · 1 line
2.25.1
author maintainer
#31 lore raw

PATCH 32/206 RDMA/iw_cgxb4: Fix an error handling path in 'c4iw_connect()'

In reply to Sasha Levin

From: Christophe JAILLET <[email protected]>

[ Upstream commit 9067f2f0b41d7e817fc8c5259bab1f17512b0147 ]

We should jump to fail3 in order to undo the 'xa_insert_irq()' call.

---
 drivers/infiniband/hw/cxgb4/cm.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/infiniband/hw/cxgb4/cm.c +2 -2
index 16145b0a14583..3fd3dfa3478b7 100644
@@ -3293,7 +3293,7 @@ int c4iw_connect(struct iw_cm_id *cm_id, struct iw_cm_conn_param *conn_param)
 		if (raddr->sin_addr.s_addr == htonl(INADDR_ANY)) {
 			err = pick_local_ipaddrs(dev, cm_id);
 			if (err)
-				goto fail2;
+				goto fail3;
 		}
 
 		/* find a route */
@@ -3315,7 +3315,7 @@ int c4iw_connect(struct iw_cm_id *cm_id, struct iw_cm_conn_param *conn_param)
 		if (ipv6_addr_type(&raddr6->sin6_addr) == IPV6_ADDR_ANY) {
 			err = pick_local_ip6addrs(dev, cm_id);
 			if (err)
-				goto fail2;
+				goto fail3;
 		}
 
 		/* find a route */
Signature · 1 line
2.25.1
author maintainer
#35 lore raw

PATCH 36/206 scsi: pm80xx: Cleanup command when a reset times out

In reply to Sasha Levin

From: peter chang <[email protected]>

[ Upstream commit 51c1c5f6ed64c2b65a8cf89dac136273d25ca540 ]

Added the fix so the if driver properly sent the abort it tries to remove it from the firmware's list of outstanding commands regardless of the abort status. This means that the task gets freed 'now' rather than possibly getting freed later when the scsi layer thinks it's leaked but still valid.

---
 drivers/scsi/pm8001/pm8001_sas.c | 50 +++++++++++++++++++++++---------
 1 file changed, 37 insertions(+), 13 deletions(-)
drivers/scsi/pm8001/pm8001_sas.c +37 -13
index 5be4212312cb0..49cf2b65de223 100644
@@ -1184,8 +1184,8 @@ int pm8001_abort_task(struct sas_task *task)
 	pm8001_ha = pm8001_find_ha_by_dev(dev);
 	device_id = pm8001_dev->device_id;
 	phy_id = pm8001_dev->attached_phy;
-	rc = pm8001_find_tag(task, &tag);
-	if (rc == 0) {
+	ret = pm8001_find_tag(task, &tag);
+	if (ret == 0) {
 		pm8001_printk("no tag for task:%p\n", task);
 		return TMF_RESP_FUNC_FAILED;
 	}
@@ -1223,26 +1223,50 @@ int pm8001_abort_task(struct sas_task *task)
 
 			/* 2. Send Phy Control Hard Reset */
 			reinit_completion(&completion);
+			phy->port_reset_status = PORT_RESET_TMO;
 			phy->reset_success = false;
 			phy->enable_completion = &completion;
 			phy->reset_completion = &completion_reset;
 			ret = PM8001_CHIP_DISP->phy_ctl_req(pm8001_ha, phy_id,
 				PHY_HARD_RESET);
-			if (ret)
-				goto out;
-			PM8001_MSG_DBG(pm8001_ha,
-				pm8001_printk("Waiting for local phy ctl\n"));
-			wait_for_completion(&completion);
-			if (!phy->reset_success)
+			if (ret) {
+				phy->enable_completion = NULL;
+				phy->reset_completion = NULL;
 				goto out;
+			}
 
-			/* 3. Wait for Port Reset complete / Port reset TMO */
+			/* In the case of the reset timeout/fail we still
+			 * abort the command at the firmware. The assumption
+			 * here is that the drive is off doing something so
+			 * that it's not processing requests, and we want to
+			 * avoid getting a completion for this and either
+			 * leaking the task in libsas or losing the race and
+			 * getting a double free.
+			 */
 			PM8001_MSG_DBG(pm8001_ha,
+				pm8001_printk("Waiting for local phy ctl\n"));
+			ret = wait_for_completion_timeout(&completion,
+					PM8001_TASK_TIMEOUT * HZ);
+			if (!ret || !phy->reset_success) {
+				phy->enable_completion = NULL;
+				phy->reset_completion = NULL;
+			} else {
+				/* 3. Wait for Port Reset complete or
+				 * Port reset TMO
+				 */
+				PM8001_MSG_DBG(pm8001_ha,
 				pm8001_printk("Waiting for Port reset\n"));
-			wait_for_completion(&completion_reset);
-			if (phy->port_reset_status) {
-				pm8001_dev_gone_notify(dev);
-				goto out;
+				ret = wait_for_completion_timeout(
+					&completion_reset,
+					PM8001_TASK_TIMEOUT * HZ);
+				if (!ret)
+					phy->reset_completion = NULL;
+				WARN_ON(phy->port_reset_status ==
+						PORT_RESET_TMO);
+				if (phy->port_reset_status == PORT_RESET_TMO) {
+					pm8001_dev_gone_notify(dev);
+					goto out;
+				}
 			}
 
 			/*
Signature · 1 line
2.25.1
author maintainer
#38 lore raw

PATCH 39/206 ASoC: max98090: remove msleep in PLL unlocked workaround

In reply to Sasha Levin

From: Tzung-Bi Shih <[email protected]>

[ Upstream commit acb874a7c049ec49d8fc66c893170fb42c01bdf7 ]

It was observed Baytrail-based chromebooks could cause continuous PLL unlocked when using playback stream and capture stream simultaneously. Specifically, starting a capture stream after started a playback stream. As a result, the audio data could corrupt or turn completely silent.

As the datasheet suggested, the maximum PLL lock time should be 7 msec. The workaround resets the codec softly by toggling SHDN off and on if PLL failed to lock for 10 msec. Notably, there is no suggested hold time for SHDN off.

On Baytrail-based chromebooks, it would easily happen continuous PLL unlocked if there is a 10 msec delay between SHDN off and on. Removes the msleep().

---
 sound/soc/codecs/max98090.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
sound/soc/codecs/max98090.c +7 -1
index 89b6e187ac235..a5b0c40ee545f 100644
@@ -2130,10 +2130,16 @@ static void max98090_pll_work(struct max98090_priv *max98090)
 
 	dev_info_ratelimited(component->dev, "PLL unlocked\n");
 
+	/*
+	 * As the datasheet suggested, the maximum PLL lock time should be
+	 * 7 msec.  The workaround resets the codec softly by toggling SHDN
+	 * off and on if PLL failed to lock for 10 msec.  Notably, there is
+	 * no suggested hold time for SHDN off.
+	 */
+
 	/* Toggle shutdown OFF then ON */
 	snd_soc_component_update_bits(component, M98090_REG_DEVICE_SHUTDOWN,
 			    M98090_SHDNN_MASK, 0);
-	msleep(10);
 	snd_soc_component_update_bits(component, M98090_REG_DEVICE_SHUTDOWN,
 			    M98090_SHDNN_MASK, M98090_SHDNN_MASK);
 
Signature · 1 line
2.25.1
author maintainer
#42 lore raw

PATCH 43/206 neigh_stat_seq_next() should increase position index

In reply to Sasha Levin

From: Vasily Averin <[email protected]>

[ Upstream commit 1e3f9f073c47bee7c23e77316b07bc12338c5bba ]

if seq_file .next fuction does not change position index, read after some lseek can generate unexpected output.

https://bugzilla.kernel.org/show_bug.cgi?id=206283

---
 net/core/neighbour.c | 1 +
 1 file changed, 1 insertion(+)
net/core/neighbour.c +1 -0
index bf738ec68cb53..6e890f51b7d86 100644
@@ -2844,6 +2844,7 @@ static void *neigh_stat_seq_next(struct seq_file *seq, void *v, loff_t *pos)
 		*pos = cpu+1;
 		return per_cpu_ptr(tbl->stats, cpu);
 	}
+	(*pos)++;
 	return NULL;
 }
 
Signature · 1 line
2.25.1
author maintainer
#40 lore raw

PATCH 41/206 KVM: arm/arm64: vgic: Fix potential double free dist->spis in __kvm_vgic_destroy()

In reply to Sasha Levin

From: Miaohe Lin <[email protected]>

[ Upstream commit 0bda9498dd45280e334bfe88b815ebf519602cc3 ]

In kvm_vgic_dist_init() called from kvm_vgic_map_resources(), if dist->vgic_model is invalid, dist->spis will be freed without set dist->spis = NULL. And in vgicv2 resources clean up path, __kvm_vgic_destroy() will be called to free allocated resources. And dist->spis will be freed again in clean up chain because we forget to set dist->spis = NULL in kvm_vgic_dist_init() failed path. So double free would happen.

---
 virt/kvm/arm/vgic/vgic-init.c | 1 +
 1 file changed, 1 insertion(+)
virt/kvm/arm/vgic/vgic-init.c +1 -0
index cd75df25fe140..2fc1777da50d2 100644
@@ -187,6 +187,7 @@ static int kvm_vgic_dist_init(struct kvm *kvm, unsigned int nr_spis)
 			break;
 		default:
 			kfree(dist->spis);
+			dist->spis = NULL;
 			return -EINVAL;
 		}
 	}
Signature · 6 lines
2.25.1

_______________________________________________
kvmarm mailing list
[email protected]
https://lists.cs.columbia.edu/mailman/listinfo/kvmarm
author maintainer
#46 lore raw

PATCH 47/206 media: ti-vpe: cal: Restrict DMA to avoid memory corruption

In reply to Sasha Levin

From: Nikhil Devshatwar <[email protected]>

[ Upstream commit 6e72eab2e7b7a157d554b8f9faed7676047be7c1 ]

When setting DMA for video capture from CSI channel, if the DMA size is not given, it ends up writing as much data as sent by the camera.

This may lead to overwriting the buffers causing memory corruption. Observed green lines on the default framebuffer.

Restrict the DMA to maximum height as specified in the S_FMT ioctl.

---
 drivers/media/platform/ti-vpe/cal.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/media/platform/ti-vpe/cal.c +4 -2
index be3155275a6ba..d945323fc437d 100644
@@ -684,12 +684,13 @@ static void pix_proc_config(struct cal_ctx *ctx)
 }
 
 static void cal_wr_dma_config(struct cal_ctx *ctx,
-			      unsigned int width)
+			      unsigned int width, unsigned int height)
 {
 	u32 val;
 
 	val = reg_read(ctx->dev, CAL_WR_DMA_CTRL(ctx->csi2_port));
 	set_field(&val, ctx->csi2_port, CAL_WR_DMA_CTRL_CPORT_MASK);
+	set_field(&val, height, CAL_WR_DMA_CTRL_YSIZE_MASK);
 	set_field(&val, CAL_WR_DMA_CTRL_DTAG_PIX_DAT,
 		  CAL_WR_DMA_CTRL_DTAG_MASK);
 	set_field(&val, CAL_WR_DMA_CTRL_MODE_CONST,
@@ -1315,7 +1316,8 @@ static int cal_start_streaming(struct vb2_queue *vq, unsigned int count)
 	csi2_lane_config(ctx);
 	csi2_ctx_config(ctx);
 	pix_proc_config(ctx);
-	cal_wr_dma_config(ctx, ctx->v_fmt.fmt.pix.bytesperline);
+	cal_wr_dma_config(ctx, ctx->v_fmt.fmt.pix.bytesperline,
+			  ctx->v_fmt.fmt.pix.height);
 	cal_wr_dma_addr(ctx, addr);
 	csi2_ppi_enable(ctx);
 
Signature · 1 line
2.25.1
author maintainer
#45 lore raw

PATCH 46/206 seqlock: Require WRITE_ONCE surrounding raw_seqcount_barrier

In reply to Sasha Levin

From: Marco Elver <[email protected]>

[ Upstream commit bf07132f96d426bcbf2098227fb680915cf44498 ]

This patch proposes to require marked atomic accesses surrounding raw_write_seqcount_barrier. We reason that otherwise there is no way to guarantee propagation nor atomicity of writes before/after the barrier [1]. For example, consider the compiler tears stores either before or after the barrier; in this case, readers may observe a partial value, and because readers are unaware that writes are going on (writes are not in a seq-writer critical section), will complete the seq-reader critical section while having observed some partial state.
[1] https://lwn.net/Articles/793253/

This came up when designing and implementing KCSAN, because KCSAN would flag these accesses as data-races. After careful analysis, our reasoning as above led us to conclude that the best thing to do is to propose an amendment to the raw_seqcount_barrier usage.

---
 include/linux/seqlock.h | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
include/linux/seqlock.h +9 -2
index bcf4cf26b8c89..a42a29952889c 100644
@@ -243,6 +243,13 @@ static inline void raw_write_seqcount_end(seqcount_t *s)
  * usual consistency guarantee. It is one wmb cheaper, because we can
  * collapse the two back-to-back wmb()s.
  *
+ * Note that, writes surrounding the barrier should be declared atomic (e.g.
+ * via WRITE_ONCE): a) to ensure the writes become visible to other threads
+ * atomically, avoiding compiler optimizations; b) to document which writes are
+ * meant to propagate to the reader critical section. This is necessary because
+ * neither writes before and after the barrier are enclosed in a seq-writer
+ * critical section that would ensure readers are aware of ongoing writes.
+ *
  *      seqcount_t seq;
  *      bool X = true, Y = false;
  *
@@ -262,11 +269,11 @@ static inline void raw_write_seqcount_end(seqcount_t *s)
  *
  *      void write(void)
  *      {
- *              Y = true;
+ *              WRITE_ONCE(Y, true);
  *
  *              raw_write_seqcount_barrier(seq);
  *
- *              X = false;
+ *              WRITE_ONCE(X, false);
  *      }
  */
 static inline void raw_write_seqcount_barrier(seqcount_t *s)
Signature · 1 line
2.25.1
author maintainer
#53 lore raw

PATCH 54/206 s390/cpum_sf: Use kzalloc and minor changes

In reply to Sasha Levin

From: Thomas Richter <[email protected]>

[ Upstream commit 32dab6828c42f087439d3e2617dc7283546bd8f7 ]

Use kzalloc() to allocate auxiliary buffer structure initialized with all zeroes to avoid random value in trace output.

Avoid double access to SBD hardware flags.

---
 arch/s390/kernel/perf_cpum_sf.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)
arch/s390/kernel/perf_cpum_sf.c +4 -5
index 74a296cea21cc..0e6d01225a670 100644
@@ -1377,8 +1377,8 @@ static int aux_output_begin(struct perf_output_handle *handle,
 		idx = aux->empty_mark + 1;
 		for (i = 0; i < range_scan; i++, idx++) {
 			te = aux_sdb_trailer(aux, idx);
-			te->flags = te->flags & ~SDB_TE_BUFFER_FULL_MASK;
-			te->flags = te->flags & ~SDB_TE_ALERT_REQ_MASK;
+			te->flags &= ~(SDB_TE_BUFFER_FULL_MASK |
+				       SDB_TE_ALERT_REQ_MASK);
 			te->overflow = 0;
 		}
 		/* Save the position of empty SDBs */
@@ -1425,8 +1425,7 @@ static bool aux_set_alert(struct aux_buffer *aux, unsigned long alert_index,
 	te = aux_sdb_trailer(aux, alert_index);
 	do {
 		orig_flags = te->flags;
-		orig_overflow = te->overflow;
-		*overflow = orig_overflow;
+		*overflow = orig_overflow = te->overflow;
 		if (orig_flags & SDB_TE_BUFFER_FULL_MASK) {
 			/*
 			 * SDB is already set by hardware.
@@ -1660,7 +1659,7 @@ static void *aux_buffer_setup(struct perf_event *event, void **pages,
 	}
 
 	/* Allocate aux_buffer struct for the event */
-	aux = kmalloc(sizeof(struct aux_buffer), GFP_KERNEL);
+	aux = kzalloc(sizeof(struct aux_buffer), GFP_KERNEL);
 	if (!aux)
 		goto no_aux;
 	sfb = &aux->sfb;
Signature · 1 line
2.25.1
author maintainer
#44 lore raw

PATCH 45/206 ipv6_route_seq_next should increase position index

In reply to Sasha Levin

From: Vasily Averin <[email protected]>

[ Upstream commit 4fc427e0515811250647d44de38d87d7b0e0790f ]

if seq_file .next fuction does not change position index, read after some lseek can generate unexpected output.

https://bugzilla.kernel.org/show_bug.cgi?id=206283

---
 net/ipv6/ip6_fib.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)
net/ipv6/ip6_fib.c +2 -5
index 5e8979c1f76d8..28b51f4aa6418 100644
@@ -2372,14 +2372,13 @@ static void *ipv6_route_seq_next(struct seq_file *seq, void *v, loff_t *pos)
 	struct net *net = seq_file_net(seq);
 	struct ipv6_route_iter *iter = seq->private;
 
+	++(*pos);
 	if (!v)
 		goto iter_table;
 
 	n = rcu_dereference_bh(((struct fib6_info *)v)->fib6_next);
-	if (n) {
-		++*pos;
+	if (n)
 		return n;
-	}
 
 iter_table:
 	ipv6_route_check_sernum(iter);
@@ -2387,8 +2386,6 @@ iter_table:
 	r = fib6_walk_continue(&iter->w);
 	spin_unlock_bh(&iter->tbl->tb6_lock);
 	if (r > 0) {
-		if (v)
-			++*pos;
 		return iter->w.leaf;
 	} else if (r < 0) {
 		fib6_walker_unlink(net, &iter->w);
Signature · 1 line
2.25.1
author maintainer
#51 lore raw

PATCH 52/206 efi/arm: Defer probe of PCIe backed efifb on DT systems

In reply to Sasha Levin

From: Ard Biesheuvel <[email protected]>

[ Upstream commit 64c8a0cd0a535891d5905c3a1651150f0f141439 ]

The new of_devlink support breaks PCIe probing on ARM platforms booting via UEFI if the firmware exposes a EFI framebuffer that is backed by a PCI device. The reason is that the probing order gets reversed, resulting in a resource conflict on the framebuffer memory window when the PCIe probes last, causing it to give up entirely.

Given that we rely on PCI quirks to deal with EFI framebuffers that get moved around in memory, we cannot simply drop the memory reservation, so instead, let's use the device link infrastructure to register this dependency, and force the probing to occur in the expected order.

---
 drivers/firmware/efi/arm-init.c | 107 ++++++++++++++++++++++++++++++--
 1 file changed, 103 insertions(+), 4 deletions(-)
drivers/firmware/efi/arm-init.c +103 -4
index 1a6a77df8a5e8..85533ec55396a 100644
@@ -14,10 +14,12 @@
 #define pr_fmt(fmt)	"efi: " fmt
 
 #include <linux/efi.h>
+#include <linux/fwnode.h>
 #include <linux/init.h>
 #include <linux/memblock.h>
 #include <linux/mm_types.h>
 #include <linux/of.h>
+#include <linux/of_address.h>
 #include <linux/of_fdt.h>
 #include <linux/platform_device.h>
 #include <linux/screen_info.h>
@@ -271,15 +273,112 @@ void __init efi_init(void)
 		efi_memmap_unmap();
 }
 
+static bool efifb_overlaps_pci_range(const struct of_pci_range *range)
+{
+	u64 fb_base = screen_info.lfb_base;
+
+	if (screen_info.capabilities & VIDEO_CAPABILITY_64BIT_BASE)
+		fb_base |= (u64)(unsigned long)screen_info.ext_lfb_base << 32;
+
+	return fb_base >= range->cpu_addr &&
+	       fb_base < (range->cpu_addr + range->size);
+}
+
+static struct device_node *find_pci_overlap_node(void)
+{
+	struct device_node *np;
+
+	for_each_node_by_type(np, "pci") {
+		struct of_pci_range_parser parser;
+		struct of_pci_range range;
+		int err;
+
+		err = of_pci_range_parser_init(&parser, np);
+		if (err) {
+			pr_warn("of_pci_range_parser_init() failed: %d\n", err);
+			continue;
+		}
+
+		for_each_of_pci_range(&parser, &range)
+			if (efifb_overlaps_pci_range(&range))
+				return np;
+	}
+	return NULL;
+}
+
+/*
+ * If the efifb framebuffer is backed by a PCI graphics controller, we have
+ * to ensure that this relation is expressed using a device link when
+ * running in DT mode, or the probe order may be reversed, resulting in a
+ * resource reservation conflict on the memory window that the efifb
+ * framebuffer steals from the PCIe host bridge.
+ */
+static int efifb_add_links(const struct fwnode_handle *fwnode,
+			   struct device *dev)
+{
+	struct device_node *sup_np;
+	struct device *sup_dev;
+
+	sup_np = find_pci_overlap_node();
+
+	/*
+	 * If there's no PCI graphics controller backing the efifb, we are
+	 * done here.
+	 */
+	if (!sup_np)
+		return 0;
+
+	sup_dev = get_dev_from_fwnode(&sup_np->fwnode);
+	of_node_put(sup_np);
+
+	/*
+	 * Return -ENODEV if the PCI graphics controller device hasn't been
+	 * registered yet.  This ensures that efifb isn't allowed to probe
+	 * and this function is retried again when new devices are
+	 * registered.
+	 */
+	if (!sup_dev)
+		return -ENODEV;
+
+	/*
+	 * If this fails, retrying this function at a later point won't
+	 * change anything. So, don't return an error after this.
+	 */
+	if (!device_link_add(dev, sup_dev, 0))
+		dev_warn(dev, "device_link_add() failed\n");
+
+	put_device(sup_dev);
+
+	return 0;
+}
+
+static const struct fwnode_operations efifb_fwnode_ops = {
+	.add_links = efifb_add_links,
+};
+
+static struct fwnode_handle efifb_fwnode = {
+	.ops = &efifb_fwnode_ops,
+};
+
 static int __init register_gop_device(void)
 {
-	void *pd;
+	struct platform_device *pd;
+	int err;
 
 	if (screen_info.orig_video_isVGA != VIDEO_TYPE_EFI)
 		return 0;
 
-	pd = platform_device_register_data(NULL, "efi-framebuffer", 0,
-					   &screen_info, sizeof(screen_info));
-	return PTR_ERR_OR_ZERO(pd);
+	pd = platform_device_alloc("efi-framebuffer", 0);
+	if (!pd)
+		return -ENOMEM;
+
+	if (IS_ENABLED(CONFIG_PCI))
+		pd->dev.fwnode = &efifb_fwnode;
+
+	err = platform_device_add_data(pd, &screen_info, sizeof(screen_info));
+	if (err)
+		return err;
+
+	return platform_device_add(pd);
 }
 subsys_initcall(register_gop_device);
Signature · 1 line
2.25.1
author maintainer
#52 lore raw

PATCH 53/206 dmaengine: zynqmp_dma: fix burst length configuration

In reply to Sasha Levin

From: Matthias Fend <[email protected]>

[ Upstream commit cc88525ebffc757e00cc5a5d61da6271646c7f5f ]

Since the dma engine expects the burst length register content as power of 2 value, the burst length needs to be converted first. Additionally add a burst length range check to avoid corrupting unrelated register bits.

---
 drivers/dma/xilinx/zynqmp_dma.c | 24 +++++++++++++++---------
 1 file changed, 15 insertions(+), 9 deletions(-)
drivers/dma/xilinx/zynqmp_dma.c +15 -9
index 73de6a6179fcd..e002ff8413e2a 100644
@@ -127,10 +127,12 @@
 /* Max transfer size per descriptor */
 #define ZYNQMP_DMA_MAX_TRANS_LEN	0x40000000
 
+/* Max burst lengths */
+#define ZYNQMP_DMA_MAX_DST_BURST_LEN    32768U
+#define ZYNQMP_DMA_MAX_SRC_BURST_LEN    32768U
+
 /* Reset values for data attributes */
 #define ZYNQMP_DMA_AXCACHE_VAL		0xF
-#define ZYNQMP_DMA_ARLEN_RST_VAL	0xF
-#define ZYNQMP_DMA_AWLEN_RST_VAL	0xF
 
 #define ZYNQMP_DMA_SRC_ISSUE_RST_VAL	0x1F
 
@@ -536,17 +538,19 @@ static void zynqmp_dma_handle_ovfl_int(struct zynqmp_dma_chan *chan, u32 status)
 
 static void zynqmp_dma_config(struct zynqmp_dma_chan *chan)
 {
-	u32 val;
+	u32 val, burst_val;
 
 	val = readl(chan->regs + ZYNQMP_DMA_CTRL0);
 	val |= ZYNQMP_DMA_POINT_TYPE_SG;
 	writel(val, chan->regs + ZYNQMP_DMA_CTRL0);
 
 	val = readl(chan->regs + ZYNQMP_DMA_DATA_ATTR);
+	burst_val = __ilog2_u32(chan->src_burst_len);
 	val = (val & ~ZYNQMP_DMA_ARLEN) |
-		(chan->src_burst_len << ZYNQMP_DMA_ARLEN_OFST);
+		((burst_val << ZYNQMP_DMA_ARLEN_OFST) & ZYNQMP_DMA_ARLEN);
+	burst_val = __ilog2_u32(chan->dst_burst_len);
 	val = (val & ~ZYNQMP_DMA_AWLEN) |
-		(chan->dst_burst_len << ZYNQMP_DMA_AWLEN_OFST);
+		((burst_val << ZYNQMP_DMA_AWLEN_OFST) & ZYNQMP_DMA_AWLEN);
 	writel(val, chan->regs + ZYNQMP_DMA_DATA_ATTR);
 }
 
@@ -562,8 +566,10 @@ static int zynqmp_dma_device_config(struct dma_chan *dchan,
 {
 	struct zynqmp_dma_chan *chan = to_chan(dchan);
 
-	chan->src_burst_len = config->src_maxburst;
-	chan->dst_burst_len = config->dst_maxburst;
+	chan->src_burst_len = clamp(config->src_maxburst, 1U,
+		ZYNQMP_DMA_MAX_SRC_BURST_LEN);
+	chan->dst_burst_len = clamp(config->dst_maxburst, 1U,
+		ZYNQMP_DMA_MAX_DST_BURST_LEN);
 
 	return 0;
 }
@@ -884,8 +890,8 @@ static int zynqmp_dma_chan_probe(struct zynqmp_dma_device *zdev,
 		return PTR_ERR(chan->regs);
 
 	chan->bus_width = ZYNQMP_DMA_BUS_WIDTH_64;
-	chan->dst_burst_len = ZYNQMP_DMA_AWLEN_RST_VAL;
-	chan->src_burst_len = ZYNQMP_DMA_ARLEN_RST_VAL;
+	chan->dst_burst_len = ZYNQMP_DMA_MAX_DST_BURST_LEN;
+	chan->src_burst_len = ZYNQMP_DMA_MAX_SRC_BURST_LEN;
 	err = of_property_read_u32(node, "xlnx,bus-width", &chan->bus_width);
 	if (err < 0) {
 		dev_err(&pdev->dev, "missing xlnx,bus-width property\n");
Signature · 1 line
2.25.1
author maintainer
#63 lore raw

PATCH 62/206 ceph: ensure we have a new cap before continuing in fill_inode

In reply to Sasha Levin

From: Jeff Layton <[email protected]>

[ Upstream commit 9a6bed4fe0c8bf57785cbc4db9f86086cb9b193d ]

If the caller passes in a NULL cap_reservation, and we can't allocate one then ensure that we fail gracefully.

---
 fs/ceph/inode.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
fs/ceph/inode.c +4 -1
index 1e438e0faf77e..3c24fb77ef325 100644
@@ -764,8 +764,11 @@ static int fill_inode(struct inode *inode, struct page *locked_page,
 	info_caps = le32_to_cpu(info->cap.caps);
 
 	/* prealloc new cap struct */
-	if (info_caps && ceph_snap(inode) == CEPH_NOSNAP)
+	if (info_caps && ceph_snap(inode) == CEPH_NOSNAP) {
 		new_cap = ceph_get_cap(mdsc, caps_reservation);
+		if (!new_cap)
+			return -ENOMEM;
+	}
 
 	/*
 	 * prealloc xattr data, if it looks like we'll need it.  only
Signature · 1 line
2.25.1
author maintainer
#67 lore raw

PATCH 66/206 mm/swapfile.c: swap_next should increase position index

In reply to Sasha Levin

From: Vasily Averin <[email protected]>

[ Upstream commit 10c8d69f314d557d94d74ec492575ae6a4f1eb1c ]

If seq_file .next fuction does not change position index, read after some lseek can generate unexpected output.

In Aug 2018 NeilBrown noticed commit 1f4aace60b0e ("fs/seq_file.c:
simplify seq_file iteration code and interface") "Some ->next functions do not increment *pos when they return NULL... Note that such ->next functions are buggy and should be fixed. A simple demonstration is

dd if=/proc/swaps bs=1000 skip=1

Choose any block size larger than the size of /proc/swaps. This will always show the whole last line of /proc/swaps"

Described problem is still actual. If you make lseek into middle of last output line following read will output end of last line and whole last line once again.

  $ dd if=/proc/swaps bs=1  # usual output
  Filename				Type		Size	Used	Priority
  /dev/dm-0                               partition	4194812	97536	-2
  104+0 records in
  104+0 records out
  104 bytes copied
  $ dd if=/proc/swaps bs=40 skip=1    # last line was generated twice
  dd: /proc/swaps: cannot skip to specified offset
  v/dm-0                               partition	4194812	97536	-2
  /dev/dm-0                               partition	4194812	97536	-2
  3+1 records in
  3+1 records out
  131 bytes copied

https://bugzilla.kernel.org/show_bug.cgi?id=206283

---
 mm/swapfile.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
mm/swapfile.c +1 -1
index 0047dcaf93697..c3684cfa9534e 100644
@@ -2738,10 +2738,10 @@ static void *swap_next(struct seq_file *swap, void *v, loff_t *pos)
 	else
 		type = si->type + 1;
 
+	++(*pos);
 	for (; (si = swap_type_to_swap_info(type)); type++) {
 		if (!(si->flags & SWP_USED) || !si->swap_map)
 			continue;
-		++*pos;
 		return si;
 	}
 
Signature · 1 line
2.25.1
author maintainer
#64 lore raw

PATCH 63/206 selftests/ftrace: fix glob selftest

In reply to Sasha Levin

From: Sven Schnelle <[email protected]>

[ Upstream commit af4ddd607dff7aabd466a4a878e01b9f592a75ab ]

test.d/ftrace/func-filter-glob.tc is failing on s390 because it has ARCH_INLINE_SPIN_LOCK and friends set to 'y'. So the usual __raw_spin_lock symbol isn't in the ftrace function list. Change '*aw*lock' to '*spin*lock' which would hopefully match some of the locking functions on all platforms.

---
 .../testing/selftests/ftrace/test.d/ftrace/func-filter-glob.tc  | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/testing/selftests/ftrace/test.d/ftrace/func-filter-glob.tc +1 -1
index 27a54a17da65d..f4e92afab14b2 100644
@@ -30,7 +30,7 @@ ftrace_filter_check '*schedule*' '^.*schedule.*$'
 ftrace_filter_check 'schedule*' '^schedule.*$'
 
 # filter by *mid*end
-ftrace_filter_check '*aw*lock' '.*aw.*lock$'
+ftrace_filter_check '*pin*lock' '.*pin.*lock$'
 
 # filter by start*mid*
 ftrace_filter_check 'mutex*try*' '^mutex.*try.*'
Signature · 1 line
2.25.1
author maintainer
#68 lore raw

PATCH 67/206 mm: pagewalk: fix termination condition in walk_pte_range()

In reply to Sasha Levin

From: Steven Price <[email protected]>

[ Upstream commit c02a98753e0a36ba65a05818626fa6adeb4e7c97 ]

If walk_pte_range() is called with a 'end' argument that is beyond the last page of memory (e.g. ~0UL) then the comparison between 'addr' and 'end' will always fail and the loop will be infinite. Instead change the comparison to >= while accounting for overflow.

Cc Albert Ou <[email protected]>
Cc Alexandre Ghiti <[email protected]>
Cc Andy Lutomirski <[email protected]>
Cc Ard Biesheuvel <[email protected]>
Cc Arnd Bergmann <[email protected]>
Cc Benjamin Herrenschmidt <[email protected]>
Cc Borislav Petkov <[email protected]>
Cc Catalin Marinas <[email protected]>
Cc Christian Borntraeger <[email protected]>
Cc Dave Hansen <[email protected]>
Cc David S. Miller <[email protected]>
Cc Heiko Carstens <[email protected]>
Cc "H. Peter Anvin" <[email protected]>
Cc Ingo Molnar <[email protected]>
Cc James Hogan <[email protected]>
Cc James Morse <[email protected]>
Cc Jerome Glisse <[email protected]>
Cc "Liang, Kan" <[email protected]>
Cc Mark Rutland <[email protected]>
Cc Michael Ellerman <[email protected]>
Cc Paul Burton <[email protected]>
Cc Paul Mackerras <[email protected]>
Cc Paul Walmsley <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Ralf Baechle <[email protected]>
Cc Russell King <[email protected]>
Cc Thomas Gleixner <[email protected]>
Cc Vasily Gorbik <[email protected]>
Cc Vineet Gupta <[email protected]>
Cc Will Deacon <[email protected]>
Cc Zong Li <[email protected]>
---
 mm/pagewalk.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
mm/pagewalk.c +2 -2
index c3084ff2569d2..3c0930d94a295 100644
@@ -15,9 +15,9 @@ static int walk_pte_range(pmd_t *pmd, unsigned long addr, unsigned long end,
 		err = walk->pte_entry(pte, addr, addr + PAGE_SIZE, walk);
 		if (err)
 		       break;
-		addr += PAGE_SIZE;
-		if (addr == end)
+		if (addr >= end - PAGE_SIZE)
 			break;
+		addr += PAGE_SIZE;
 		pte++;
 	}
 
Signature · 1 line
2.25.1
author maintainer
#70 lore raw

PATCH 69/206 KVM: fix overflow of zero page refcount with ksm running

In reply to Sasha Levin

From: Zhuang Yanying <[email protected]>

[ Upstream commit 7df003c85218b5f5b10a7f6418208f31e813f38f ]

We are testing Virtual Machine with KSM on v5.4-rc2 kernel, and found the zero_page refcount overflow.
The cause of refcount overflow is increased in try_async_pf (get_user_page) without being decreased in mmu_set_spte() while handling ept violation.
In kvm_release_pfn_clean(), only unreserved page will call put_page. However, zero page is reserved.
So, as well as creating and destroy vm, the refcount of zero page will continue to increase until it overflows.

step1:
echo 10000 > /sys/kernel/pages_to_scan/pages_to_scan echo 1 > /sys/kernel/pages_to_scan/run
echo 1 > /sys/kernel/pages_to_scan/use_zero_pages

step2:
just create several normal qemu kvm vms.
And destroy it after 10s.
Repeat this action all the time.

After a long period of time, all domains hang because of the refcount of zero page overflow.

Qemu print error log as follow:
…
error: kvm run failed Bad address
EAX=00006cdc EBX=00000008 ECX=80202001 EDX=078bfbfd ESI=ffffffff EDI=00000000 EBP=00000008 ESP=00006cc4 EIP=000efd75 EFL=00010002 [-------] CPL=0 II=0 A20=1 SMM=0 HLT=0
ES =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA]
CS =0008 00000000 ffffffff 00c09b00 DPL=0 CS32 [-RA]

 SS =0010 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
 DS =0010 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
 FS =0010 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
 GS =0010 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]

LDT=0000 00000000 0000ffff 00008200 DPL=0 LDT
TR =0000 00000000 0000ffff 00008b00 DPL=0 TSS32-busy
GDT= 000f7070 00000037
IDT= 000f70ae 00000000
CR0=00000011 CR2=00000000 CR3=00000000 CR4=00000000
DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000
DR6=00000000ffff0ff0 DR7=0000000000000400
EFER=0000000000000000
Code=00 01 00 00 00 e9 e8 00 00 00 c7 05 4c 55 0f 00 01 00 00 00 <8b> 35 00 00 01 00 8b 3d 04 00 01 00 b8 d8 d3 00 00 c1 e0 08 0c ea a3 00 00 01 00 c7 05 04 …

Meanwhile, a kernel warning is departed.

 [40914.836375] WARNING: CPU: 3 PID: 82067 at ./include/linux/mm.h:987 try_get_page+0x1f/0x30
 [40914.836412] CPU: 3 PID: 82067 Comm: CPU 0/KVM Kdump: loaded Tainted: G           OE     5.2.0-rc2 #5
 [40914.836415] RIP: 0010:try_get_page+0x1f/0x30
 [40914.836417] Code: 40 00 c3 0f 1f 84 00 00 00 00 00 48 8b 47 08 a8 01 75 11 8b 47 34 85 c0 7e 10 f0 ff 47 34 b8 01 00 00 00 c3 48 8d 78 ff eb e9 <0f> 0b 31 c0 c3 66 90 66 2e 0f 1f 84 00 0
 0 00 00 00 48 8b 47 08 a8
 [40914.836418] RSP: 0018:ffffb4144e523988 EFLAGS: 00010286
 [40914.836419] RAX: 0000000080000000 RBX: 0000000000000326 RCX: 0000000000000000
 [40914.836420] RDX: 0000000000000000 RSI: 00004ffdeba10000 RDI: ffffdf07093f6440
 [40914.836421] RBP: ffffdf07093f6440 R08: 800000424fd91225 R09: 0000000000000000
 [40914.836421] R10: ffff9eb41bfeebb8 R11: 0000000000000000 R12: ffffdf06bbd1e8a8
 [40914.836422] R13: 0000000000000080 R14: 800000424fd91225 R15: ffffdf07093f6440
 [40914.836423] FS:  00007fb60ffff700(0000) GS:ffff9eb4802c0000(0000) knlGS:0000000000000000
 [40914.836425] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 [40914.836426] CR2: 0000000000000000 CR3: 0000002f220e6002 CR4: 00000000003626e0
 [40914.836427] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 [40914.836427] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 [40914.836428] Call Trace:
 [40914.836433]  follow_page_pte+0x302/0x47b
 [40914.836437]  __get_user_pages+0xf1/0x7d0
 [40914.836441]  ? irq_work_queue+0x9/0x70
 [40914.836443]  get_user_pages_unlocked+0x13f/0x1e0
 [40914.836469]  __gfn_to_pfn_memslot+0x10e/0x400 [kvm]
 [40914.836486]  try_async_pf+0x87/0x240 [kvm]
 [40914.836503]  tdp_page_fault+0x139/0x270 [kvm]
 [40914.836523]  kvm_mmu_page_fault+0x76/0x5e0 [kvm]
 [40914.836588]  vcpu_enter_guest+0xb45/0x1570 [kvm]
 [40914.836632]  kvm_arch_vcpu_ioctl_run+0x35d/0x580 [kvm]
 [40914.836645]  kvm_vcpu_ioctl+0x26e/0x5d0 [kvm]
 [40914.836650]  do_vfs_ioctl+0xa9/0x620
 [40914.836653]  ksys_ioctl+0x60/0x90
 [40914.836654]  __x64_sys_ioctl+0x16/0x20
 [40914.836658]  do_syscall_64+0x5b/0x180
 [40914.836664]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
 [40914.836666] RIP: 0033:0x7fb61cb6bfc7
---
 virt/kvm/kvm_main.c | 1 +
 1 file changed, 1 insertion(+)
virt/kvm/kvm_main.c +1 -0
index 2155b52b17eca..595502f8d4a27 100644
@@ -169,6 +169,7 @@ bool kvm_is_reserved_pfn(kvm_pfn_t pfn)
 	 */
 	if (pfn_valid(pfn))
 		return PageReserved(pfn_to_page(pfn)) &&
+		       !is_zero_pfn(pfn) &&
 		       !kvm_is_zone_device_pfn(pfn);
 
 	return true;
Signature · 1 line
2.25.1
author maintainer
#72 lore raw

PATCH 71/206 skbuff: fix a data race in skb_queue_len()

In reply to Sasha Levin

From: Qian Cai <[email protected]>

[ Upstream commit 86b18aaa2b5b5bb48e609cd591b3d2d0fdbe0442 ]

sk_buff.qlen can be accessed concurrently as noticed by KCSAN,

 BUG: KCSAN: data-race in __skb_try_recv_from_queue / unix_dgram_sendmsg

read to 0xffff8a1b1d8a81c0 of 4 bytes by task 5371 on cpu 96:

  unix_dgram_sendmsg+0x9a9/0xb70 include/linux/skbuff.h:1821
				 net/unix/af_unix.c:1761
  ____sys_sendmsg+0x33e/0x370
  ___sys_sendmsg+0xa6/0xf0
  __sys_sendmsg+0x69/0xf0
  __x64_sys_sendmsg+0x51/0x70
  do_syscall_64+0x91/0xb47
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

write to 0xffff8a1b1d8a81c0 of 4 bytes by task 1 on cpu 99:

  __skb_try_recv_from_queue+0x327/0x410 include/linux/skbuff.h:2029
  __skb_try_recv_datagram+0xbe/0x220
  unix_dgram_recvmsg+0xee/0x850
  ____sys_recvmsg+0x1fb/0x210
  ___sys_recvmsg+0xa2/0xf0
  __sys_recvmsg+0x66/0xf0
  __x64_sys_recvmsg+0x51/0x70
  do_syscall_64+0x91/0xb47
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

Since only the read is operating as lockless, it could introduce a logic bug in unix_recvq_full() due to the load tearing. Fix it by adding a lockless variant of skb_queue_len() and unix_recvq_full() where READ_ONCE() is on the read while WRITE_ONCE() is on the write similar to the commit d7d16a89350a ("net: add skb_queue_empty_lockless()").

---
 include/linux/skbuff.h | 14 +++++++++++++-
 net/unix/af_unix.c     | 11 +++++++++--
 2 files changed, 22 insertions(+), 3 deletions(-)
include/linux/skbuff.h +13 -1
index 25407c206e732..f0474ea735695 100644
@@ -1688,6 +1688,18 @@ static inline __u32 skb_queue_len(const struct sk_buff_head *list_)
 	return list_->qlen;
 }
 
+/**
+ *	skb_queue_len_lockless	- get queue length
+ *	@list_: list to measure
+ *
+ *	Return the length of an &sk_buff queue.
+ *	This variant can be used in lockless contexts.
+ */
+static inline __u32 skb_queue_len_lockless(const struct sk_buff_head *list_)
+{
+	return READ_ONCE(list_->qlen);
+}
+
 /**
  *	__skb_queue_head_init - initialize non-spinlock portions of sk_buff_head
  *	@list: queue to initialize
@@ -1895,7 +1907,7 @@ static inline void __skb_unlink(struct sk_buff *skb, struct sk_buff_head *list)
 {
 	struct sk_buff *next, *prev;
 
-	list->qlen--;
+	WRITE_ONCE(list->qlen, list->qlen - 1);
 	next	   = skb->next;
 	prev	   = skb->prev;
 	skb->next  = skb->prev = NULL;
net/unix/af_unix.c +9 -2
index 2318e2e2748f4..2020306468af4 100644
@@ -192,11 +192,17 @@ static inline int unix_may_send(struct sock *sk, struct sock *osk)
 	return unix_peer(osk) == NULL || unix_our_peer(sk, osk);
 }
 
-static inline int unix_recvq_full(struct sock const *sk)
+static inline int unix_recvq_full(const struct sock *sk)
 {
 	return skb_queue_len(&sk->sk_receive_queue) > sk->sk_max_ack_backlog;
 }
 
+static inline int unix_recvq_full_lockless(const struct sock *sk)
+{
+	return skb_queue_len_lockless(&sk->sk_receive_queue) >
+		READ_ONCE(sk->sk_max_ack_backlog);
+}
+
 struct sock *unix_peer_get(struct sock *s)
 {
 	struct sock *peer;
@@ -1788,7 +1794,8 @@ restart_locked:
 	 * - unix_peer(sk) == sk by time of get but disconnected before lock
 	 */
 	if (other != sk &&
-	    unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {
+	    unlikely(unix_peer(other) != sk &&
+	    unix_recvq_full_lockless(other))) {
 		if (timeo) {
 			timeo = unix_wait_for_peer(other, timeo);
 
Signature · 1 line
2.25.1
author maintainer
#69 lore raw

PATCH 68/206 Bluetooth: prefetch channel before killing sock

In reply to Sasha Levin

From: Hillf Danton <[email protected]>

[ Upstream commit 2a154903cec20fb64ff4d7d617ca53c16f8fd53a ]

Prefetch channel before killing sock in order to fix UAF like

 BUG: KASAN: use-after-free in l2cap_sock_release+0x24c/0x290 net/bluetooth/l2cap_sock.c:1212
 Read of size 8 at addr ffff8880944904a0 by task syz-fuzzer/9751
Reported-by [email protected]
Fixes 6c08fc896b60 ("Bluetooth: Fix refcount use-after-free issue")
Cc Manish Mandlik <[email protected]>
---
 net/bluetooth/l2cap_sock.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
net/bluetooth/l2cap_sock.c +6 -4
index d128750e47305..5572042f04531 100644
@@ -1190,6 +1190,7 @@ static int l2cap_sock_release(struct socket *sock)
 {
 	struct sock *sk = sock->sk;
 	int err;
+	struct l2cap_chan *chan;
 
 	BT_DBG("sock %p, sk %p", sock, sk);
 
@@ -1199,15 +1200,16 @@ static int l2cap_sock_release(struct socket *sock)
 	bt_sock_unlink(&l2cap_sk_list, sk);
 
 	err = l2cap_sock_shutdown(sock, 2);
+	chan = l2cap_pi(sk)->chan;
 
-	l2cap_chan_hold(l2cap_pi(sk)->chan);
-	l2cap_chan_lock(l2cap_pi(sk)->chan);
+	l2cap_chan_hold(chan);
+	l2cap_chan_lock(chan);
 
 	sock_orphan(sk);
 	l2cap_sock_kill(sk);
 
-	l2cap_chan_unlock(l2cap_pi(sk)->chan);
-	l2cap_chan_put(l2cap_pi(sk)->chan);
+	l2cap_chan_unlock(chan);
+	l2cap_chan_put(chan);
 
 	return err;
 }
Signature · 1 line
2.25.1
author maintainer
#77 lore raw

PATCH 76/206 drm/omap: fix possible object reference leak

In reply to Sasha Levin

From: Wen Yang <[email protected]>

[ Upstream commit 47340e46f34a3b1d80e40b43ae3d7a8da34a3541 ]

The call to of_find_matching_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage.

Detected by coccinelle with the following warnings:
drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:212:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function. drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:237:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function.

---
 drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c +3 -1
index 3bfb95d230e0e..d8fb686c1fda9 100644
@@ -193,7 +193,7 @@ static int __init omapdss_boot_init(void)
 	dss = of_find_matching_node(NULL, omapdss_of_match);
 
 	if (dss == NULL || !of_device_is_available(dss))
-		return 0;
+		goto put_node;
 
 	omapdss_walk_device(dss, true);
 
@@ -218,6 +218,8 @@ static int __init omapdss_boot_init(void)
 		kfree(n);
 	}
 
+put_node:
+	of_node_put(dss);
 	return 0;
 }
 
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#79 lore raw

PATCH 78/206 crypto: chelsio - This fixes the kernel panic which occurs during a libkcapi test

In reply to Sasha Levin

From: Ayush Sawal <[email protected]>

[ Upstream commit 9195189e00a7db55e7d448cee973cae87c5a3c71 ]

The libkcapi test which causes kernel panic is
aead asynchronous vmsplice multiple test.

./bin/kcapi -v -d 4 -x 10 -c "ccm(aes)"
-q 4edb58e8d5eb6bc711c43a6f3693daebde2e5524f1b55297abb29f003236e43d -t a7877c99 -n 674742abd0f5ba -k 2861fd0253705d7875c95ba8a53171b4 -a fb7bc304a3909e66e2e0c5ef952712dd884ce3e7324171369f2c5db1adc48c7d

This patch avoids dma_mapping of a zero length sg which causes the panic, by using sg_nents_for_len which maps only upto a specific length

---
 drivers/crypto/chelsio/chcr_algo.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/crypto/chelsio/chcr_algo.c +3 -2
index 9b3c259f081d3..ee508bbbb7504 100644
@@ -2418,8 +2418,9 @@ int chcr_aead_dma_map(struct device *dev,
 	else
 		reqctx->b0_dma = 0;
 	if (req->src == req->dst) {
-		error = dma_map_sg(dev, req->src, sg_nents(req->src),
-				   DMA_BIDIRECTIONAL);
+		error = dma_map_sg(dev, req->src,
+				sg_nents_for_len(req->src, dst_size),
+					DMA_BIDIRECTIONAL);
 		if (!error)
 			goto err;
 	} else {
Signature · 1 line
2.25.1
author maintainer
#78 lore raw

PATCH 77/206 clk: stratix10: use do_div() for 64-bit calculation

In reply to Sasha Levin

From: Dinh Nguyen <[email protected]>

[ Upstream commit cc26ed7be46c5f5fa45f3df8161ed7ca3c4d318c ]

do_div() macro to perform u64 division and guards against overflow if the result is too large for the unsigned long return type.

---
 drivers/clk/socfpga/clk-pll-s10.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/clk/socfpga/clk-pll-s10.c +3 -1
index c4d0b6f6abf2e..fc2e2839fe570 100644
@@ -38,7 +38,9 @@ static unsigned long clk_pll_recalc_rate(struct clk_hw *hwclk,
 	/* read VCO1 reg for numerator and denominator */
 	reg = readl(socfpgaclk->hw.reg);
 	refdiv = (reg & SOCFPGA_PLL_REFDIV_MASK) >> SOCFPGA_PLL_REFDIV_SHIFT;
-	vco_freq = (unsigned long long)parent_rate / refdiv;
+
+	vco_freq = parent_rate;
+	do_div(vco_freq, refdiv);
 
 	/* Read mdiv and fdiv from the fdbck register */
 	reg = readl(socfpgaclk->hw.reg + 0x4);
Signature · 1 line
2.25.1
author maintainer
#82 lore raw

PATCH 81/206 perf test: Fix test trace+probe_vfs_getname.sh on s390

In reply to Sasha Levin

From: Thomas Richter <[email protected]>

[ Upstream commit 2bbc83537614517730e9f2811195004b712de207 ]

This test places a kprobe to function getname_flags() in the kernel which has the following prototype:

struct filename *getname_flags(const char __user *filename, int flags, int *empty)

The 'filename' argument points to a filename located in user space memory.

Looking at commit 88903c464321c ("tracing/probe: Add ustring type for user-space string") the kprobe should indicate that user space memory is accessed.

Output before:

[root@m35lp76 perf]# ./perf test 66 67
66: Use vfs_getname probe to get syscall args filenames : FAILED!
67: Check open filename arg using perf trace + vfs_getname: FAILED! [root@m35lp76 perf]#

Output after:

[root@m35lp76 perf]# ./perf test 66 67
66: Use vfs_getname probe to get syscall args filenames : Ok
67: Check open filename arg using perf trace + vfs_getname: Ok [root@m35lp76 perf]#

Comments from Masami Hiramatsu:

This bug doesn't happen on x86 or other archs on which user address space and kernel address space is the same. On some arches (ppc64 in this case?) user address space is partially or completely the same as kernel address space.

(Yes, they switch the world when running into the kernel) In this case, we need to use different data access functions for each space.

That is why I introduced the "ustring" type for kprobe events.

As far as I can see, Thomas's patch is sane. Thomas, could you show us your result on your test environment?

Comments from Thomas Richter:

Test results for s/390 included above.

---
 tools/perf/tests/shell/lib/probe_vfs_getname.sh | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/perf/tests/shell/lib/probe_vfs_getname.sh +1 -1
index 7cb99b433888b..c2cc42daf9242 100644
@@ -14,7 +14,7 @@ add_probe_vfs_getname() {
 	if [ $had_vfs_getname -eq 1 ] ; then
 		line=$(perf probe -L getname_flags 2>&1 | egrep 'result.*=.*filename;' | sed -r 's/[[:space:]]+([[:digit:]]+)[[:space:]]+result->uptr.*/\1/')
 		perf probe -q       "vfs_getname=getname_flags:${line} pathname=result->name:string" || \
-		perf probe $verbose "vfs_getname=getname_flags:${line} pathname=filename:string"
+		perf probe $verbose "vfs_getname=getname_flags:${line} pathname=filename:ustring"
 	fi
 }
 
Signature · 1 line
2.25.1
author maintainer
#86 lore raw

PATCH 85/206 media: staging/imx: Missing assignment in imx_media_capture_device_register()

In reply to Sasha Levin

From: Dan Carpenter <[email protected]>

[ Upstream commit ef0ed05dcef8a74178a8b480cce23a377b1de2b8 ]

There was supposed to be a "ret = " assignment here, otherwise the error handling on the next line won't work.

Fixes 64b5a49df486 ("[media] media: imx: Add Capture Device Interface")
---
 drivers/staging/media/imx/imx-media-capture.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/staging/media/imx/imx-media-capture.c +1 -1
index 256039ce561e6..81a3370551dbc 100644
@@ -678,7 +678,7 @@ int imx_media_capture_device_register(struct imx_media_video_dev *vdev)
 	/* setup default format */
 	fmt_src.pad = priv->src_sd_pad;
 	fmt_src.which = V4L2_SUBDEV_FORMAT_ACTIVE;
-	v4l2_subdev_call(sd, pad, get_fmt, NULL, &fmt_src);
+	ret = v4l2_subdev_call(sd, pad, get_fmt, NULL, &fmt_src);
 	if (ret) {
 		v4l2_err(sd, "failed to get src_sd format\n");
 		goto unreg;
Signature · 1 line
2.25.1
author maintainer
#91 lore raw

PATCH 90/206 drm/amd/display: dal_ddc_i2c_payloads_create can fail causing panic

In reply to Sasha Levin

From: Aric Cyr <[email protected]>

[ Upstream commit 6a6c4a4d459ecacc9013c45dcbf2bc9747fdbdbd ]

[Why]
Since the i2c payload allocation can fail need to check return codes

[How]
Clean up i2c payload allocations and check for errors

---
 .../gpu/drm/amd/display/dc/core/dc_link_ddc.c | 52 +++++++++----------
 1 file changed, 25 insertions(+), 27 deletions(-)
drivers/gpu/drm/amd/display/dc/core/dc_link_ddc.c +25 -27
index 46c9cb47a96e5..145af3bb2dfcb 100644
@@ -127,22 +127,16 @@ struct aux_payloads {
 	struct vector payloads;
 };
 
-static struct i2c_payloads *dal_ddc_i2c_payloads_create(struct dc_context *ctx, uint32_t count)
+static bool dal_ddc_i2c_payloads_create(
+		struct dc_context *ctx,
+		struct i2c_payloads *payloads,
+		uint32_t count)
 {
-	struct i2c_payloads *payloads;
-
-	payloads = kzalloc(sizeof(struct i2c_payloads), GFP_KERNEL);
-
-	if (!payloads)
-		return NULL;
-
 	if (dal_vector_construct(
 		&payloads->payloads, ctx, count, sizeof(struct i2c_payload)))
-		return payloads;
-
-	kfree(payloads);
-	return NULL;
+		return true;
 
+	return false;
 }
 
 static struct i2c_payload *dal_ddc_i2c_payloads_get(struct i2c_payloads *p)
@@ -155,14 +149,12 @@ static uint32_t dal_ddc_i2c_payloads_get_count(struct i2c_payloads *p)
 	return p->payloads.count;
 }
 
-static void dal_ddc_i2c_payloads_destroy(struct i2c_payloads **p)
+static void dal_ddc_i2c_payloads_destroy(struct i2c_payloads *p)
 {
-	if (!p || !*p)
+	if (!p)
 		return;
-	dal_vector_destruct(&(*p)->payloads);
-	kfree(*p);
-	*p = NULL;
 
+	dal_vector_destruct(&p->payloads);
 }
 
 static struct aux_payloads *dal_ddc_aux_payloads_create(struct dc_context *ctx, uint32_t count)
@@ -580,9 +572,13 @@ bool dal_ddc_service_query_ddc_data(
 
 	uint32_t payloads_num = write_payloads + read_payloads;
 
+
 	if (write_size > EDID_SEGMENT_SIZE || read_size > EDID_SEGMENT_SIZE)
 		return false;
 
+	if (!payloads_num)
+		return false;
+
 	/*TODO: len of payload data for i2c and aux is uint8!!!!,
 	 *  but we want to read 256 over i2c!!!!*/
 	if (dal_ddc_service_is_in_aux_transaction_mode(ddc)) {
@@ -613,23 +609,25 @@ bool dal_ddc_service_query_ddc_data(
 		dal_ddc_aux_payloads_destroy(&payloads);
 
 	} else {
-		struct i2c_payloads *payloads =
-			dal_ddc_i2c_payloads_create(ddc->ctx, payloads_num);
+		struct i2c_command command = {0};
+		struct i2c_payloads payloads;
 
-		struct i2c_command command = {
-			.payloads = dal_ddc_i2c_payloads_get(payloads),
-			.number_of_payloads = 0,
-			.engine = DDC_I2C_COMMAND_ENGINE,
-			.speed = ddc->ctx->dc->caps.i2c_speed_in_khz };
+		if (!dal_ddc_i2c_payloads_create(ddc->ctx, &payloads, payloads_num))
+			return false;
+
+		command.payloads = dal_ddc_i2c_payloads_get(&payloads);
+		command.number_of_payloads = 0;
+		command.engine = DDC_I2C_COMMAND_ENGINE;
+		command.speed = ddc->ctx->dc->caps.i2c_speed_in_khz;
 
 		dal_ddc_i2c_payloads_add(
-			payloads, address, write_size, write_buf, true);
+			&payloads, address, write_size, write_buf, true);
 
 		dal_ddc_i2c_payloads_add(
-			payloads, address, read_size, read_buf, false);
+			&payloads, address, read_size, read_buf, false);
 
 		command.number_of_payloads =
-			dal_ddc_i2c_payloads_get_count(payloads);
+			dal_ddc_i2c_payloads_get_count(&payloads);
 
 		ret = dm_helpers_submit_i2c(
 				ddc->ctx,
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#94 lore raw

PATCH 93/206 bus: hisi_lpc: Fixup IO ports addresses to avoid use-after-free in host removal

In reply to Sasha Levin

From: John Garry <[email protected]>

[ Upstream commit a6dd255bdd7d00bbdbf78ba00bde9fc64f86c3a7 ]

Some released ACPI FW for Huawei boards describes incorrect the port IO address range for child devices, in that it tells us the IO port max range is 0x3fff for each child device, which is not correct. The address range should be [e4:e8) or similar. With this incorrect upper range, the child device IO port resources overlap.

As such, the kernel thinks that the LPC host serial device is a child of the IPMI device:

root@(none)$ more /proc/ioports
[...]
00ffc0e3-00ffffff : hisi-lpc-ipmi.0.auto
  00ffc0e3-00ffc0e3 : ipmi_si
  00ffc0e4-00ffc0e4 : ipmi_si
  00ffc0e5-00ffc0e5 : ipmi_si
  00ffc2f7-00ffffff : serial8250.1.auto
    00ffc2f7-00ffc2fe : serial
root@(none)$

They should both be siblings. Note that these are logical PIO addresses, which have a direct mapping from the FW IO port ranges.

This shows up as a real issue when we enable CONFIG_KASAN and CONFIG_DEBUG_TEST_DRIVER_REMOVE - we see use-after-free warnings in the host removal path:

==================================================================

BUG: KASAN: use-after-free in release_resource+0x38/0xc8
Read of size 8 at addr ffff0026accdbc38 by task swapper/0/1

CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.5.0-rc6-00001-g68e186e77b5c-dirty #1593
Hardware name: Huawei Taishan 2180 /D03, BIOS Hisilicon D03 IT20 Nemo 2.0 RC0 03/30/2018
Call trace:
dump_backtrace+0x0/0x290
show_stack+0x14/0x20
dump_stack+0xf0/0x14c
print_address_description.isra.9+0x6c/0x3b8
__kasan_report+0x12c/0x23c
kasan_report+0xc/0x18
__asan_load8+0x94/0xb8
release_resource+0x38/0xc8
platform_device_del.part.10+0x80/0xe0
platform_device_unregister+0x20/0x38
hisi_lpc_acpi_remove_subdev+0x10/0x20
device_for_each_child+0xc8/0x128
hisi_lpc_acpi_remove+0x4c/0xa8
hisi_lpc_remove+0xbc/0xc0
platform_drv_remove+0x3c/0x68
really_probe+0x174/0x548
driver_probe_device+0x7c/0x148
device_driver_attach+0x94/0xa0
__driver_attach+0xa4/0x110
bus_for_each_dev+0xe8/0x158
driver_attach+0x30/0x40
bus_add_driver+0x234/0x2f0
driver_register+0xbc/0x1d0
__platform_driver_register+0x7c/0x88
hisi_lpc_driver_init+0x18/0x20
do_one_initcall+0xb4/0x258
kernel_init_freeable+0x248/0x2c0
kernel_init+0x10/0x118
ret_from_fork+0x10/0x1c

...

The issue here is that the kernel created an incorrect parent-child resource dependency between two devices, and references the false parent node when deleting the second child device, when it had been deleted already.

Fix up the child device resources from FW to create proper IO port resource relationships for broken FW.

With this, the IO port layout looks more healthy:

root@(none)$ more /proc/ioports
[...]
00ffc0e3-00ffc0e7 : hisi-lpc-ipmi.0.auto
  00ffc0e3-00ffc0e3 : ipmi_si
  00ffc0e4-00ffc0e4 : ipmi_si
  00ffc0e5-00ffc0e5 : ipmi_si
00ffc2f7-00ffc2ff : serial8250.1.auto
  00ffc2f7-00ffc2fe : serial
---
 drivers/bus/hisi_lpc.c | 27 +++++++++++++++++++++++++--
 1 file changed, 25 insertions(+), 2 deletions(-)
drivers/bus/hisi_lpc.c +25 -2
index e31c02dc77709..cbd970fb02f18 100644
@@ -358,6 +358,26 @@ static int hisi_lpc_acpi_xlat_io_res(struct acpi_device *adev,
 	return 0;
 }
 
+/*
+ * Released firmware describes the IO port max address as 0x3fff, which is
+ * the max host bus address. Fixup to a proper range. This will probably
+ * never be fixed in firmware.
+ */
+static void hisi_lpc_acpi_fixup_child_resource(struct device *hostdev,
+					       struct resource *r)
+{
+	if (r->end != 0x3fff)
+		return;
+
+	if (r->start == 0xe4)
+		r->end = 0xe4 + 0x04 - 1;
+	else if (r->start == 0x2f8)
+		r->end = 0x2f8 + 0x08 - 1;
+	else
+		dev_warn(hostdev, "unrecognised resource %pR to fixup, ignoring\n",
+			 r);
+}
+
 /*
  * hisi_lpc_acpi_set_io_res - set the resources for a child
  * @child: the device node to be updated the I/O resource
@@ -419,8 +439,11 @@ static int hisi_lpc_acpi_set_io_res(struct device *child,
 		return -ENOMEM;
 	}
 	count = 0;
-	list_for_each_entry(rentry, &resource_list, node)
-		resources[count++] = *rentry->res;
+	list_for_each_entry(rentry, &resource_list, node) {
+		resources[count] = *rentry->res;
+		hisi_lpc_acpi_fixup_child_resource(hostdev, &resources[count]);
+		count++;
+	}
 
 	acpi_dev_free_resource_list(&resource_list);
 
Signature · 1 line
2.25.1
author maintainer
#99 lore raw

PATCH 98/206 perf jevents: Fix leak of mapfile memory

In reply to Sasha Levin

From: John Garry <[email protected]>

[ Upstream commit 3f5777fbaf04c58d940526a22a2e0c813c837936 ]

The memory for global pointer is never freed during normal program execution, so let's do that in the main function exit as a good programming practice.

A stray blank line is also removed.

---
 tools/perf/pmu-events/jevents.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)
tools/perf/pmu-events/jevents.c +9 -6
index c17e594041712..6631970f96832 100644
@@ -1064,10 +1064,9 @@ static int process_one_file(const char *fpath, const struct stat *sb,
  */
 int main(int argc, char *argv[])
 {
-	int rc;
+	int rc, ret = 0;
 	int maxfds;
 	char ldirname[PATH_MAX];
-
 	const char *arch;
 	const char *output_file;
 	const char *start_dirname;
@@ -1138,7 +1137,8 @@ int main(int argc, char *argv[])
 		/* Make build fail */
 		fclose(eventsfp);
 		free_arch_std_events();
-		return 1;
+		ret = 1;
+		goto out_free_mapfile;
 	} else if (rc) {
 		goto empty_map;
 	}
@@ -1156,14 +1156,17 @@ int main(int argc, char *argv[])
 		/* Make build fail */
 		fclose(eventsfp);
 		free_arch_std_events();
-		return 1;
+		ret = 1;
 	}
 
-	return 0;
+
+	goto out_free_mapfile;
 
 empty_map:
 	fclose(eventsfp);
 	create_empty_mapping(output_file);
 	free_arch_std_events();
-	return 0;
+out_free_mapfile:
+	free(mapfile);
+	return ret;
 }
Signature · 1 line
2.25.1
author maintainer
#98 lore raw

PATCH 97/206 ext4: fix a data race at inode->i_disksize

In reply to Sasha Levin

From: Qiujun Huang <[email protected]>

[ Upstream commit dce8e237100f60c28cc66effb526ba65a01d8cb3 ]

KCSAN find inode->i_disksize could be accessed concurrently.

BUG: KCSAN: data-race in ext4_mark_iloc_dirty / ext4_write_end

write (marked) to 0xffff8b8932f40090 of 8 bytes by task 66792 on cpu 0:

 ext4_write_end+0x53f/0x5b0
 ext4_da_write_end+0x237/0x510
 generic_perform_write+0x1c4/0x2a0
 ext4_buffered_write_iter+0x13a/0x210
 ext4_file_write_iter+0xe2/0x9b0
 new_sync_write+0x29c/0x3a0
 __vfs_write+0x92/0xa0
 vfs_write+0xfc/0x2a0
 ksys_write+0xe8/0x140
 __x64_sys_write+0x4c/0x60
 do_syscall_64+0x8a/0x2a0
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

read to 0xffff8b8932f40090 of 8 bytes by task 14414 on cpu 1:

 ext4_mark_iloc_dirty+0x716/0x1190
 ext4_mark_inode_dirty+0xc9/0x360
 ext4_convert_unwritten_extents+0x1bc/0x2a0
 ext4_convert_unwritten_io_end_vec+0xc5/0x150
 ext4_put_io_end+0x82/0x130
 ext4_writepages+0xae7/0x16f0
 do_writepages+0x64/0x120
 __writeback_single_inode+0x7d/0x650
 writeback_sb_inodes+0x3a4/0x860
 __writeback_inodes_wb+0xc4/0x150
 wb_writeback+0x43f/0x510
 wb_workfn+0x3b2/0x8a0
 process_one_work+0x39b/0x7e0
 worker_thread+0x88/0x650
 kthread+0x1d4/0x1f0
 ret_from_fork+0x35/0x40

The plain read is outside of inode->i_data_sem critical section which results in a data race. Fix it by adding READ_ONCE().

---
 fs/ext4/inode.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/ext4/inode.c +1 -1
index cd833f4e64ef1..52be4c9650241 100644
@@ -5315,7 +5315,7 @@ static int ext4_do_update_inode(handle_t *handle,
 		raw_inode->i_file_acl_high =
 			cpu_to_le16(ei->i_file_acl >> 32);
 	raw_inode->i_file_acl_lo = cpu_to_le32(ei->i_file_acl);
-	if (ei->i_disksize != ext4_isize(inode->i_sb, raw_inode)) {
+	if (READ_ONCE(ei->i_disksize) != ext4_isize(inode->i_sb, raw_inode)) {
 		ext4_isize_set(raw_inode, ei->i_disksize);
 		need_datasync = 1;
 	}
Signature · 1 line
2.25.1
author maintainer
#100 lore raw

PATCH 99/206 mm: avoid data corruption on CoW fault into PFN-mapped VMA

In reply to Sasha Levin

From: "Kirill A. Shutemov" <[email protected]>

[ Upstream commit c3e5ea6ee574ae5e845a40ac8198de1fb63bb3ab ]

Jeff Moyer has reported that one of xfstests triggers a warning when run on DAX-enabled filesystem:

	WARNING: CPU: 76 PID: 51024 at mm/memory.c:2317 wp_page_copy+0xc40/0xd50
	...
	wp_page_copy+0x98c/0xd50 (unreliable)
	do_wp_page+0xd8/0xad0
	__handle_mm_fault+0x748/0x1b90
	handle_mm_fault+0x120/0x1f0
	__do_page_fault+0x240/0xd70
	do_page_fault+0x38/0xd0
	handle_page_fault+0x10/0x30

The warning happens on failed __copy_from_user_inatomic() which tries to copy data into a CoW page.

This happens because of race between MADV_DONTNEED and CoW page fault:

	CPU0					CPU1
 handle_mm_fault()
   do_wp_page()
     wp_page_copy()
       do_wp_page()
					madvise(MADV_DONTNEED)
					  zap_page_range()
					    zap_pte_range()
					      ptep_get_and_clear_full()
					      <TLB flush>
	 __copy_from_user_inatomic()
	 sees empty PTE and fails
	 WARN_ON_ONCE(1)
	 clear_page()

The solution is to re-try __copy_from_user_inatomic() under PTL after checking that PTE is matches the orig_pte.

The second copy attempt can still fail, like due to non-readable PTE, but there's nothing reasonable we can do about, except clearing the CoW page.

---
 mm/memory.c | 35 +++++++++++++++++++++++++++--------
 1 file changed, 27 insertions(+), 8 deletions(-)
mm/memory.c +27 -8
index fcad8a0d943d3..eeae63bd95027 100644
@@ -2353,7 +2353,7 @@ static inline bool cow_user_page(struct page *dst, struct page *src,
 	bool ret;
 	void *kaddr;
 	void __user *uaddr;
-	bool force_mkyoung;
+	bool locked = false;
 	struct vm_area_struct *vma = vmf->vma;
 	struct mm_struct *mm = vma->vm_mm;
 	unsigned long addr = vmf->address;
@@ -2378,11 +2378,11 @@ static inline bool cow_user_page(struct page *dst, struct page *src,
 	 * On architectures with software "accessed" bits, we would
 	 * take a double page fault, so mark it accessed here.
 	 */
-	force_mkyoung = arch_faults_on_old_pte() && !pte_young(vmf->orig_pte);
-	if (force_mkyoung) {
+	if (arch_faults_on_old_pte() && !pte_young(vmf->orig_pte)) {
 		pte_t entry;
 
 		vmf->pte = pte_offset_map_lock(mm, vmf->pmd, addr, &vmf->ptl);
+		locked = true;
 		if (!likely(pte_same(*vmf->pte, vmf->orig_pte))) {
 			/*
 			 * Other thread has already handled the fault
@@ -2406,18 +2406,37 @@ static inline bool cow_user_page(struct page *dst, struct page *src,
 	 * zeroes.
 	 */
 	if (__copy_from_user_inatomic(kaddr, uaddr, PAGE_SIZE)) {
+		if (locked)
+			goto warn;
+
+		/* Re-validate under PTL if the page is still mapped */
+		vmf->pte = pte_offset_map_lock(mm, vmf->pmd, addr, &vmf->ptl);
+		locked = true;
+		if (!likely(pte_same(*vmf->pte, vmf->orig_pte))) {
+			/* The PTE changed under us. Retry page fault. */
+			ret = false;
+			goto pte_unlock;
+		}
+
 		/*
-		 * Give a warn in case there can be some obscure
-		 * use-case
+		 * The same page can be mapped back since last copy attampt.
+		 * Try to copy again under PTL.
 		 */
-		WARN_ON_ONCE(1);
-		clear_page(kaddr);
+		if (__copy_from_user_inatomic(kaddr, uaddr, PAGE_SIZE)) {
+			/*
+			 * Give a warn in case there can be some obscure
+			 * use-case
+			 */
+warn:
+			WARN_ON_ONCE(1);
+			clear_page(kaddr);
+		}
 	}
 
 	ret = true;
 
 pte_unlock:
-	if (force_mkyoung)
+	if (locked)
 		pte_unmap_unlock(vmf->pte, vmf->ptl);
 	kunmap_atomic(kaddr);
 	flush_dcache_page(dst);
Signature · 1 line
2.25.1
author maintainer
#101 lore raw

PATCH 100/206 drm/amdgpu: increase atombios cmd timeout

In reply to Sasha Levin

From: John Clements <[email protected]>

[ Upstream commit 1b3460a8b19688ad3033b75237d40fa580a5a953 ]

mitigates race condition on BACO reset between GPU bootcode and driver reload

---
 drivers/gpu/drm/amd/amdgpu/atom.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/amd/amdgpu/atom.c +2 -2
index e9934de1b9cf8..0222bb7ea49b4 100644
@@ -742,8 +742,8 @@ static void atom_op_jump(atom_exec_context *ctx, int *ptr, int arg)
 			cjiffies = jiffies;
 			if (time_after(cjiffies, ctx->last_jump_jiffies)) {
 				cjiffies -= ctx->last_jump_jiffies;
-				if ((jiffies_to_msecs(cjiffies) > 5000)) {
-					DRM_ERROR("atombios stuck in loop for more than 5secs aborting\n");
+				if ((jiffies_to_msecs(cjiffies) > 10000)) {
+					DRM_ERROR("atombios stuck in loop for more than 10secs aborting\n");
 					ctx->abort = true;
 				}
 			} else {
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#9 lore raw

PATCH 10/206 ASoC: kirkwood: fix IRQ error handling

In reply to Sasha Levin

From: Russell King <[email protected]>

[ Upstream commit 175fc928198236037174e5c5c066fe3c4691903e ]

Propagate the error code from request_irq(), rather than returning -EBUSY.

---
 sound/soc/kirkwood/kirkwood-dma.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/kirkwood/kirkwood-dma.c +1 -1
index c6a58520d377a..255cc45905b81 100644
@@ -136,7 +136,7 @@ static int kirkwood_dma_open(struct snd_pcm_substream *substream)
 		err = request_irq(priv->irq, kirkwood_dma_irq, IRQF_SHARED,
 				  "kirkwood-i2s", priv);
 		if (err)
-			return -EBUSY;
+			return err;
 
 		/*
 		 * Enable Error interrupts. We're only ack'ing them but
Signature · 1 line
2.25.1
author maintainer
#102 lore raw

PATCH 101/206 drm/amd/display: Stop if retimer is not available

In reply to Sasha Levin

From: Rodrigo Siqueira <[email protected]>

[ Upstream commit a0e40018dcc3f59a10ca21d58f8ea8ceb1b035ac ]

Raven provides retimer feature support that requires i2c interaction in order to make it work well, all settings required for this configuration are loaded from the Atom bios which include the i2c address. If the retimer feature is not available, we should abort the attempt to set this feature, otherwise, it makes the following line return I2C_CHANNEL_OPERATION_NO_RESPONSE:

i2c_success = i2c_write(pipe_ctx, slave_address, buffer, sizeof(buffer));
...
if (!i2c_success)
ASSERT(i2c_success);

This ends up causing problems with hotplugging HDMI displays on Raven, and causes retimer settings to warn like so:

WARNING: CPU: 1 PID: 429 at

drivers/gpu/drm/amd/amdgpu/../dal/dc/core/dc_link.c:1998 write_i2c_retimer_setting+0xc2/0x3c0 [amdgpu] Modules linked in:
edac_mce_amd ccp kvm irqbypass binfmt_misc crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_codec_hdmi snd_hda_intel amdgpu(+) snd_hda_codec snd_hda_core snd_hwdep snd_pcm snd_seq_midi snd_seq_midi_event snd_rawmidi aesni_intel snd_seq amd_iommu_v2 gpu_sched aes_x86_64 crypto_simd cryptd glue_helper snd_seq_device ttm drm_kms_helper snd_timer eeepc_wmi wmi_bmof asus_wmi sparse_keymap drm mxm_wmi snd k10temp fb_sys_fops syscopyarea sysfillrect sysimgblt soundcore joydev input_leds mac_hid sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables autofs4 igb i2c_algo_bit hid_generic usbhid i2c_piix4 dca ahci hid libahci video wmi gpio_amdpt gpio_generic CPU: 1 PID: 429 Comm:
systemd-udevd Tainted: G W 5.2.0-rc1sept162019+ #1

Hardware name: System manufacturer System Product Name/ROG STRIX B450-F
GAMING, BIOS 2605 08/06/2019
RIP: 0010:write_i2c_retimer_setting+0xc2/0x3c0 [amdgpu]
Code: ff 0f b6 4d ce 44 0f b6 45 cf 44 0f b6 c8 45 89 cf 44 89 e2 48 c7
c6 f0 34 bc c0 bf 04 00 00 00 e8 63 b0 90 ff 45 84 ff 75 02 <0f> 0b 42
0f b6 04 73 8d 50 f6 80 fa 02 77 8c 3c 0a 0f 85 c8 00 00 RSP:
0018:ffffa99d02726fd0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffffa99d02727035 RCX: 0000000000000006
RDX: 0000000000000000 RSI: 0000000000000002 RDI: ffff976acc857440
RBP: ffffa99d02727018 R08: 0000000000000002 R09: 000000000002a600
R10: ffffe90610193680 R11: 00000000000005e3 R12: 000000000000005d
R13: ffff976ac4b201b8 R14: 0000000000000001 R15: 0000000000000000
FS:  00007f14f99e1680(0000) GS:ffff976acc840000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fdf212843b8 CR3: 0000000408906000 CR4: 00000000003406e0
Call Trace:
 core_link_enable_stream+0x626/0x680 [amdgpu]
 dce110_apply_ctx_to_hw+0x414/0x4e0 [amdgpu]
 dc_commit_state+0x331/0x5e0 [amdgpu]
 ? drm_calc_timestamping_constants+0xf9/0x150 [drm]
 amdgpu_dm_atomic_commit_tail+0x395/0x1e00 [amdgpu]
 ? dm_plane_helper_prepare_fb+0x20c/0x280 [amdgpu]
 commit_tail+0x42/0x70 [drm_kms_helper]
 drm_atomic_helper_commit+0x10c/0x120 [drm_kms_helper]
 amdgpu_dm_atomic_commit+0x95/0xa0 [amdgpu]
 drm_atomic_commit+0x4a/0x50 [drm]
 restore_fbdev_mode_atomic+0x1c0/0x1e0 [drm_kms_helper]
 restore_fbdev_mode+0x4c/0x160 [drm_kms_helper]
 ? _cond_resched+0x19/0x40
 drm_fb_helper_restore_fbdev_mode_unlocked+0x4e/0xa0 [drm_kms_helper]
 drm_fb_helper_set_par+0x2d/0x50 [drm_kms_helper]
 fbcon_init+0x471/0x630
 visual_init+0xd5/0x130
 do_bind_con_driver+0x20a/0x430
 do_take_over_console+0x7d/0x1b0
 do_fbcon_takeover+0x5c/0xb0
 fbcon_event_notify+0x6cd/0x8a0
 notifier_call_chain+0x4c/0x70
 blocking_notifier_call_chain+0x43/0x60
 fb_notifier_call_chain+0x1b/0x20
 register_framebuffer+0x254/0x360
 __drm_fb_helper_initial_config_and_unlock+0x2c5/0x510 [drm_kms_helper]
 drm_fb_helper_initial_config+0x35/0x40 [drm_kms_helper]
 amdgpu_fbdev_init+0xcd/0x100 [amdgpu]
 amdgpu_device_init+0x1156/0x1930 [amdgpu]
 amdgpu_driver_load_kms+0x8d/0x2e0 [amdgpu]
 drm_dev_register+0x12b/0x1c0 [drm]
 amdgpu_pci_probe+0xd3/0x160 [amdgpu]
 local_pci_probe+0x47/0xa0
 pci_device_probe+0x142/0x1b0
 really_probe+0xf5/0x3d0
 driver_probe_device+0x11b/0x130
 device_driver_attach+0x58/0x60
 __driver_attach+0xa3/0x140
 ? device_driver_attach+0x60/0x60
 ? device_driver_attach+0x60/0x60
 bus_for_each_dev+0x74/0xb0
 ? kmem_cache_alloc_trace+0x1a3/0x1c0
 driver_attach+0x1e/0x20
 bus_add_driver+0x147/0x220
 ? 0xffffffffc0cb9000
 driver_register+0x60/0x100
 ? 0xffffffffc0cb9000
 __pci_register_driver+0x5a/0x60
 amdgpu_init+0x74/0x83 [amdgpu]
 do_one_initcall+0x4a/0x1fa
 ? _cond_resched+0x19/0x40
 ? kmem_cache_alloc_trace+0x3f/0x1c0
 ? __vunmap+0x1cc/0x200
 do_init_module+0x5f/0x227
 load_module+0x2330/0x2b40
 __do_sys_finit_module+0xfc/0x120
 ? __do_sys_finit_module+0xfc/0x120
 __x64_sys_finit_module+0x1a/0x20
 do_syscall_64+0x5a/0x130
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f14f9500839
Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89

f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1f f6 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007fff9bc4f5a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000055afb5abce30 RCX: 00007f14f9500839
RDX: 0000000000000000 RSI: 000055afb5ace0f0 RDI: 0000000000000017
RBP: 000055afb5ace0f0 R08: 0000000000000000 R09: 000000000000000a
R10: 0000000000000017 R11: 0000000000000246 R12: 0000000000000000
R13: 000055afb5aad800 R14: 0000000000020000 R15: 0000000000000000

---[ end trace c286e96563966f08 ]---

This commit reworks the way that we handle i2c write for retimer in the way that we abort this configuration if the feature is not available in the device. For debug sake, we kept a simple log message in case the retimer is not available.

---
 drivers/gpu/drm/amd/display/dc/core/dc_link.c | 67 ++++++++-----------
 1 file changed, 29 insertions(+), 38 deletions(-)
drivers/gpu/drm/amd/display/dc/core/dc_link.c +29 -38
index 3abc0294c05f5..2fb2c683ad54b 100644
@@ -1576,8 +1576,7 @@ static void write_i2c_retimer_setting(
 						buffer, sizeof(buffer));
 
 			if (!i2c_success)
-				/* Write failure */
-				ASSERT(i2c_success);
+				goto i2c_write_fail;
 
 			/* Based on DP159 specs, APPLY_RX_TX_CHANGE bit in 0x0A
 			 * needs to be set to 1 on every 0xA-0xC write.
@@ -1595,8 +1594,7 @@ static void write_i2c_retimer_setting(
 						pipe_ctx->stream->sink->link->ddc,
 						slave_address, &offset, 1, &value, 1);
 					if (!i2c_success)
-						/* Write failure */
-						ASSERT(i2c_success);
+						goto i2c_write_fail;
 				}
 
 				buffer[0] = offset;
@@ -1605,8 +1603,7 @@ static void write_i2c_retimer_setting(
 				i2c_success = i2c_write(pipe_ctx, slave_address,
 						buffer, sizeof(buffer));
 				if (!i2c_success)
-					/* Write failure */
-					ASSERT(i2c_success);
+					goto i2c_write_fail;
 			}
 		}
 	}
@@ -1623,8 +1620,7 @@ static void write_i2c_retimer_setting(
 							buffer, sizeof(buffer));
 
 				if (!i2c_success)
-					/* Write failure */
-					ASSERT(i2c_success);
+					goto i2c_write_fail;
 
 				/* Based on DP159 specs, APPLY_RX_TX_CHANGE bit in 0x0A
 				 * needs to be set to 1 on every 0xA-0xC write.
@@ -1642,8 +1638,7 @@ static void write_i2c_retimer_setting(
 								pipe_ctx->stream->sink->link->ddc,
 								slave_address, &offset, 1, &value, 1);
 						if (!i2c_success)
-							/* Write failure */
-							ASSERT(i2c_success);
+							goto i2c_write_fail;
 					}
 
 					buffer[0] = offset;
@@ -1652,8 +1647,7 @@ static void write_i2c_retimer_setting(
 					i2c_success = i2c_write(pipe_ctx, slave_address,
 							buffer, sizeof(buffer));
 					if (!i2c_success)
-						/* Write failure */
-						ASSERT(i2c_success);
+						goto i2c_write_fail;
 				}
 			}
 		}
@@ -1668,8 +1662,7 @@ static void write_i2c_retimer_setting(
 		i2c_success = i2c_write(pipe_ctx, slave_address,
 				buffer, sizeof(buffer));
 		if (!i2c_success)
-			/* Write failure */
-			ASSERT(i2c_success);
+			goto i2c_write_fail;
 
 		/* Write offset 0x00 to 0x23 */
 		buffer[0] = 0x00;
@@ -1677,8 +1670,7 @@ static void write_i2c_retimer_setting(
 		i2c_success = i2c_write(pipe_ctx, slave_address,
 				buffer, sizeof(buffer));
 		if (!i2c_success)
-			/* Write failure */
-			ASSERT(i2c_success);
+			goto i2c_write_fail;
 
 		/* Write offset 0xff to 0x00 */
 		buffer[0] = 0xff;
@@ -1686,10 +1678,14 @@ static void write_i2c_retimer_setting(
 		i2c_success = i2c_write(pipe_ctx, slave_address,
 				buffer, sizeof(buffer));
 		if (!i2c_success)
-			/* Write failure */
-			ASSERT(i2c_success);
+			goto i2c_write_fail;
 
 	}
+
+	return;
+
+i2c_write_fail:
+	DC_LOG_DEBUG("Set retimer failed");
 }
 
 static void write_i2c_default_retimer_setting(
@@ -1710,8 +1706,7 @@ static void write_i2c_default_retimer_setting(
 	i2c_success = i2c_write(pipe_ctx, slave_address,
 			buffer, sizeof(buffer));
 	if (!i2c_success)
-		/* Write failure */
-		ASSERT(i2c_success);
+		goto i2c_write_fail;
 
 	/* Write offset 0x0A to 0x17 */
 	buffer[0] = 0x0A;
@@ -1719,8 +1714,7 @@ static void write_i2c_default_retimer_setting(
 	i2c_success = i2c_write(pipe_ctx, slave_address,
 			buffer, sizeof(buffer));
 	if (!i2c_success)
-		/* Write failure */
-		ASSERT(i2c_success);
+		goto i2c_write_fail;
 
 	/* Write offset 0x0B to 0xDA or 0xD8 */
 	buffer[0] = 0x0B;
@@ -1728,8 +1722,7 @@ static void write_i2c_default_retimer_setting(
 	i2c_success = i2c_write(pipe_ctx, slave_address,
 			buffer, sizeof(buffer));
 	if (!i2c_success)
-		/* Write failure */
-		ASSERT(i2c_success);
+		goto i2c_write_fail;
 
 	/* Write offset 0x0A to 0x17 */
 	buffer[0] = 0x0A;
@@ -1737,8 +1730,7 @@ static void write_i2c_default_retimer_setting(
 	i2c_success = i2c_write(pipe_ctx, slave_address,
 			buffer, sizeof(buffer));
 	if (!i2c_success)
-		/* Write failure */
-		ASSERT(i2c_success);
+		goto i2c_write_fail;
 
 	/* Write offset 0x0C to 0x1D or 0x91 */
 	buffer[0] = 0x0C;
@@ -1746,8 +1738,7 @@ static void write_i2c_default_retimer_setting(
 	i2c_success = i2c_write(pipe_ctx, slave_address,
 			buffer, sizeof(buffer));
 	if (!i2c_success)
-		/* Write failure */
-		ASSERT(i2c_success);
+		goto i2c_write_fail;
 
 	/* Write offset 0x0A to 0x17 */
 	buffer[0] = 0x0A;
@@ -1755,8 +1746,7 @@ static void write_i2c_default_retimer_setting(
 	i2c_success = i2c_write(pipe_ctx, slave_address,
 			buffer, sizeof(buffer));
 	if (!i2c_success)
-		/* Write failure */
-		ASSERT(i2c_success);
+		goto i2c_write_fail;
 
 
 	if (is_vga_mode) {
@@ -1768,8 +1758,7 @@ static void write_i2c_default_retimer_setting(
 		i2c_success = i2c_write(pipe_ctx, slave_address,
 				buffer, sizeof(buffer));
 		if (!i2c_success)
-			/* Write failure */
-			ASSERT(i2c_success);
+			goto i2c_write_fail;
 
 		/* Write offset 0x00 to 0x23 */
 		buffer[0] = 0x00;
@@ -1777,8 +1766,7 @@ static void write_i2c_default_retimer_setting(
 		i2c_success = i2c_write(pipe_ctx, slave_address,
 				buffer, sizeof(buffer));
 		if (!i2c_success)
-			/* Write failure */
-			ASSERT(i2c_success);
+			goto i2c_write_fail;
 
 		/* Write offset 0xff to 0x00 */
 		buffer[0] = 0xff;
@@ -1786,9 +1774,13 @@ static void write_i2c_default_retimer_setting(
 		i2c_success = i2c_write(pipe_ctx, slave_address,
 				buffer, sizeof(buffer));
 		if (!i2c_success)
-			/* Write failure */
-			ASSERT(i2c_success);
+			goto i2c_write_fail;
 	}
+
+	return;
+
+i2c_write_fail:
+	DC_LOG_DEBUG("Set default retimer failed");
 }
 
 static void write_i2c_redriver_setting(
@@ -1811,8 +1803,7 @@ static void write_i2c_redriver_setting(
 					buffer, sizeof(buffer));
 
 	if (!i2c_success)
-		/* Write failure */
-		ASSERT(i2c_success);
+		DC_LOG_DEBUG("Set redriver failed");
 }
 
 static void enable_link_hdmi(struct pipe_ctx *pipe_ctx)
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#103 lore raw

PATCH 102/206 ath10k: use kzalloc to read for ath10k_sdio_hif_diag_read

In reply to Sasha Levin

From: Wen Gong <[email protected]>

[ Upstream commit 402f2992b4d62760cce7c689ff216ea3bf4d6e8a ]

When use command to read values, it crashed.

command:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value count=1 bs=4 skip=$((0x100233))

It will call to ath10k_sdio_hif_diag_read with address = 0x4008cc and buf_len = 4.

Then system crash:

[ 1786.013258] Unable to handle kernel paging request at virtual address ffffffc00bd45000
[ 1786.013273] Mem abort info:
[ 1786.013281]   ESR = 0x96000045
[ 1786.013291]   Exception class = DABT (current EL), IL = 32 bits
[ 1786.013299]   SET = 0, FnV = 0
[ 1786.013307]   EA = 0, S1PTW = 0
[ 1786.013314] Data abort info:
[ 1786.013322]   ISV = 0, ISS = 0x00000045
[ 1786.013330]   CM = 0, WnR = 1
[ 1786.013342] swapper pgtable: 4k pages, 39-bit VAs, pgdp = 000000008542a60e
[ 1786.013350] [ffffffc00bd45000] pgd=0000000000000000, pud=0000000000000000
[ 1786.013368] Internal error: Oops: 96000045 [#1] PREEMPT SMP
[ 1786.013609] Process swapper/0 (pid: 0, stack limit = 0x0000000084b153c6)
[ 1786.013623] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.86 #137
[ 1786.013631] Hardware name: MediaTek krane sku176 board (DT)
[ 1786.013643] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[ 1786.013662] pc : __memcpy+0x94/0x180
[ 1786.013678] lr : swiotlb_tbl_unmap_single+0x84/0x150
[ 1786.013686] sp : ffffff8008003c60
[ 1786.013694] x29: ffffff8008003c90 x28: ffffffae96411f80
[ 1786.013708] x27: ffffffae960d2018 x26: ffffff8019a4b9a8
[ 1786.013721] x25: 0000000000000000 x24: 0000000000000001
[ 1786.013734] x23: ffffffae96567000 x22: 00000000000051d4
[ 1786.013747] x21: 0000000000000000 x20: 00000000fe6e9000
[ 1786.013760] x19: 0000000000000004 x18: 0000000000000020
[ 1786.013773] x17: 0000000000000001 x16: 0000000000000000
[ 1786.013787] x15: 00000000ffffffff x14: 00000000000044c0
[ 1786.013800] x13: 0000000000365ba4 x12: 0000000000000000
[ 1786.013813] x11: 0000000000000001 x10: 00000037be6e9000
[ 1786.013826] x9 : ffffffc940000000 x8 : 000000000bd45000
[ 1786.013839] x7 : 0000000000000000 x6 : ffffffc00bd45000
[ 1786.013852] x5 : 0000000000000000 x4 : 0000000000000000
[ 1786.013865] x3 : 0000000000000c00 x2 : 0000000000000004
[ 1786.013878] x1 : fffffff7be6e9004 x0 : ffffffc00bd45000
[ 1786.013891] Call trace:
[ 1786.013903]  __memcpy+0x94/0x180
[ 1786.013914]  unmap_single+0x6c/0x84
[ 1786.013925]  swiotlb_unmap_sg_attrs+0x54/0x80
[ 1786.013938]  __swiotlb_unmap_sg_attrs+0x8c/0xa4
[ 1786.013952]  msdc_unprepare_data+0x6c/0x84
[ 1786.013963]  msdc_request_done+0x58/0x84
[ 1786.013974]  msdc_data_xfer_done+0x1a0/0x1c8
[ 1786.013985]  msdc_irq+0x12c/0x17c
[ 1786.013996]  __handle_irq_event_percpu+0xe4/0x250
[ 1786.014006]  handle_irq_event_percpu+0x28/0x68
[ 1786.014015]  handle_irq_event+0x48/0x78
[ 1786.014026]  handle_fasteoi_irq+0xd0/0x1a0
[ 1786.014039]  __handle_domain_irq+0x84/0xc4
[ 1786.014050]  gic_handle_irq+0x124/0x1a4
[ 1786.014059]  el1_irq+0xb0/0x128
[ 1786.014072]  cpuidle_enter_state+0x298/0x328
[ 1786.014082]  cpuidle_enter+0x30/0x40
[ 1786.014094]  do_idle+0x190/0x268
[ 1786.014104]  cpu_startup_entry+0x24/0x28
[ 1786.014116]  rest_init+0xd4/0xe0
[ 1786.014126]  start_kernel+0x30c/0x38c
[ 1786.014139] Code: f8408423 f80084c3 36100062 b8404423 (b80044c3)
[ 1786.014150] ---[ end trace 3b02ddb698ea69ee ]---
[ 1786.015415] Kernel panic - not syncing: Fatal exception in interrupt
[ 1786.015433] SMP: stopping secondary CPUs
[ 1786.015447] Kernel Offset: 0x2e8d200000 from 0xffffff8008000000
[ 1786.015458] CPU features: 0x0,2188200c
[ 1786.015466] Memory Limit: none

For sdio chip, it need the memory which is kmalloc, if it is vmalloc from ath10k_mem_value_read, then it have a memory error. kzalloc of ath10k_sdio_hif_diag_read32 is the correct type, so add kzalloc in ath10k_sdio_hif_diag_read to replace the buffer which is vmalloc from ath10k_mem_value_read.

This patch only effect sdio chip.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.

---
 drivers/net/wireless/ath/ath10k/sdio.c | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)
drivers/net/wireless/ath/ath10k/sdio.c +14 -4
index 0ecaba824fb28..0cdaecb0e28a9 100644
@@ -1567,23 +1567,33 @@ static int ath10k_sdio_hif_diag_read(struct ath10k *ar, u32 address, void *buf,
 				     size_t buf_len)
 {
 	int ret;
+	void *mem;
+
+	mem = kzalloc(buf_len, GFP_KERNEL);
+	if (!mem)
+		return -ENOMEM;
 
 	/* set window register to start read cycle */
 	ret = ath10k_sdio_write32(ar, MBOX_WINDOW_READ_ADDR_ADDRESS, address);
 	if (ret) {
 		ath10k_warn(ar, "failed to set mbox window read address: %d", ret);
-		return ret;
+		goto out;
 	}
 
 	/* read the data */
-	ret = ath10k_sdio_read(ar, MBOX_WINDOW_DATA_ADDRESS, buf, buf_len);
+	ret = ath10k_sdio_read(ar, MBOX_WINDOW_DATA_ADDRESS, mem, buf_len);
 	if (ret) {
 		ath10k_warn(ar, "failed to read from mbox window data address: %d\n",
 			    ret);
-		return ret;
+		goto out;
 	}
 
-	return 0;
+	memcpy(buf, mem, buf_len);
+
+out:
+	kfree(mem);
+
+	return ret;
 }
 
 static int ath10k_sdio_hif_diag_read32(struct ath10k *ar, u32 address,
Signature · 7 lines
2.25.1


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author maintainer
#97 lore raw

PATCH 96/206 timekeeping: Prevent 32bit truncation in scale64_check_overflow()

In reply to Sasha Levin

From: Wen Yang <[email protected]>

[ Upstream commit 4cbbc3a0eeed675449b1a4d080008927121f3da3 ]

While unlikely the divisor in scale64_check_overflow() could be >= 32bit in scale64_check_overflow(). do_div() truncates the divisor to 32bit at least on 32bit platforms.

Use div64_u64() instead to avoid the truncation to 32-bit.

[ tglx: Massaged changelog ]

---
 kernel/time/timekeeping.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
kernel/time/timekeeping.c +1 -2
index 81ee5b83c9200..c66fd11d94bc4 100644
@@ -1004,9 +1004,8 @@ static int scale64_check_overflow(u64 mult, u64 div, u64 *base)
 	    ((int)sizeof(u64)*8 - fls64(mult) < fls64(rem)))
 		return -EOVERFLOW;
 	tmp *= mult;
-	rem *= mult;
 
-	do_div(rem, div);
+	rem = div64_u64(rem * mult, div);
 	*base = tmp + rem;
 	return 0;
 }
Signature · 1 line
2.25.1
author maintainer
#96 lore raw

PATCH 95/206 Bluetooth: guard against controllers sending zero'd events

In reply to Sasha Levin

From: Alain Michaud <[email protected]>

[ Upstream commit 08bb4da90150e2a225f35e0f642cdc463958d696 ]

Some controllers have been observed to send zero'd events under some conditions. This change guards against this condition as well as adding a trace to facilitate diagnosability of this condition.

---
 net/bluetooth/hci_event.c | 6 ++++++
 1 file changed, 6 insertions(+)
net/bluetooth/hci_event.c +6 -0
index 2b4a7cf03041b..ec6b3a87b3e7f 100644
@@ -5738,6 +5738,11 @@ void hci_event_packet(struct hci_dev *hdev, struct sk_buff *skb)
 	u8 status = 0, event = hdr->evt, req_evt = 0;
 	u16 opcode = HCI_OP_NOP;
 
+	if (!event) {
+		bt_dev_warn(hdev, "Received unexpected HCI Event 00000000");
+		goto done;
+	}
+
 	if (hdev->sent_cmd && bt_cb(hdev->sent_cmd)->hci.req_event == event) {
 		struct hci_command_hdr *cmd_hdr = (void *) hdev->sent_cmd->data;
 		opcode = __le16_to_cpu(cmd_hdr->opcode);
@@ -5949,6 +5954,7 @@ void hci_event_packet(struct hci_dev *hdev, struct sk_buff *skb)
 		req_complete_skb(hdev, status, opcode, orig_skb);
 	}
 
+done:
 	kfree_skb(orig_skb);
 	kfree_skb(skb);
 	hdev->stat.evt_rx++;
Signature · 1 line
2.25.1
author maintainer
#116 lore raw

PATCH 115/206 drm/msm: fix leaks if initialization fails

In reply to Sasha Levin

From: Pavel Machek <[email protected]>

[ Upstream commit 66be340f827554cb1c8a1ed7dea97920b4085af2 ]

We should free resources in unlikely case of allocation failure.

---
 drivers/gpu/drm/msm/msm_drv.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/gpu/drm/msm/msm_drv.c +4 -2
index 7f45486b6650b..3ba3ae9749bec 100644
@@ -495,8 +495,10 @@ static int msm_drm_init(struct device *dev, struct drm_driver *drv)
 	if (!dev->dma_parms) {
 		dev->dma_parms = devm_kzalloc(dev, sizeof(*dev->dma_parms),
 					      GFP_KERNEL);
-		if (!dev->dma_parms)
-			return -ENOMEM;
+		if (!dev->dma_parms) {
+			ret = -ENOMEM;
+			goto err_msm_uninit;
+		}
 	}
 	dma_set_max_seg_size(dev, DMA_BIT_MASK(32));
 
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#114 lore raw

PATCH 113/206 RDMA/cm: Remove a race freeing timewait_info

In reply to Sasha Levin

From: Jason Gunthorpe <[email protected]>

[ Upstream commit bede86a39d9dc3387ac00dcb8e1ac221676b2f25 ]

When creating a cm_id during REQ the id immediately becomes visible to the other MAD handlers, and shortly after the state is moved to IB_CM_REQ_RCVD

This allows cm_rej_handler() to run concurrently and free the work:

CPU 0 CPU1
cm_req_handler()
ib_create_cm_id()
cm_match_req()

    id_priv->state = IB_CM_REQ_RCVD
                                       cm_rej_handler()
                                         cm_acquire_id()
                                         spin_lock(&id_priv->lock)
                                         switch (id_priv->state)
  					   case IB_CM_REQ_RCVD:
                                            cm_reset_to_idle()
                                             kfree(id_priv->timewait_info);
   goto destroy
  destroy:
    kfree(id_priv->timewait_info);
                                             id_priv->timewait_info = NULL

Causing a double free or worse.

Do not free the timewait_info without also holding the id_priv->lock. Simplify this entire flow by making the free unconditional during cm_destroy_id() and removing the confusing special case error unwind during creation of the timewait_info.

This also fixes a leak of the timewait if cm_destroy_id() is called in IB_CM_ESTABLISHED with an XRC TGT QP. The state machine will be left in ESTABLISHED while it needed to transition through IB_CM_TIMEWAIT to release the timewait pointer.

Also fix a leak of the timewait_info if the caller mis-uses the API and does ib_send_cm_reqs().

Fixes a977049dacde ("[PATCH] IB: Add the kernel CM implementation")
---
 drivers/infiniband/core/cm.c | 25 +++++++++++++++----------
 1 file changed, 15 insertions(+), 10 deletions(-)
drivers/infiniband/core/cm.c +15 -10
index 64f206e11d497..4ebf63360a697 100644
@@ -1100,14 +1100,22 @@ retest:
 		break;
 	}
 
-	spin_lock_irq(&cm.lock);
+	spin_lock_irq(&cm_id_priv->lock);
+	spin_lock(&cm.lock);
+	/* Required for cleanup paths related cm_req_handler() */
+	if (cm_id_priv->timewait_info) {
+		cm_cleanup_timewait(cm_id_priv->timewait_info);
+		kfree(cm_id_priv->timewait_info);
+		cm_id_priv->timewait_info = NULL;
+	}
 	if (!list_empty(&cm_id_priv->altr_list) &&
 	    (!cm_id_priv->altr_send_port_not_ready))
 		list_del(&cm_id_priv->altr_list);
 	if (!list_empty(&cm_id_priv->prim_list) &&
 	    (!cm_id_priv->prim_send_port_not_ready))
 		list_del(&cm_id_priv->prim_list);
-	spin_unlock_irq(&cm.lock);
+	spin_unlock(&cm.lock);
+	spin_unlock_irq(&cm_id_priv->lock);
 
 	cm_free_id(cm_id->local_id);
 	cm_deref_id(cm_id_priv);
@@ -1424,7 +1432,7 @@ int ib_send_cm_req(struct ib_cm_id *cm_id,
 	/* Verify that we're not in timewait. */
 	cm_id_priv = container_of(cm_id, struct cm_id_private, id);
 	spin_lock_irqsave(&cm_id_priv->lock, flags);
-	if (cm_id->state != IB_CM_IDLE) {
+	if (cm_id->state != IB_CM_IDLE || WARN_ON(cm_id_priv->timewait_info)) {
 		spin_unlock_irqrestore(&cm_id_priv->lock, flags);
 		ret = -EINVAL;
 		goto out;
@@ -1442,12 +1450,12 @@ int ib_send_cm_req(struct ib_cm_id *cm_id,
 				 param->ppath_sgid_attr, &cm_id_priv->av,
 				 cm_id_priv);
 	if (ret)
-		goto error1;
+		goto out;
 	if (param->alternate_path) {
 		ret = cm_init_av_by_path(param->alternate_path, NULL,
 					 &cm_id_priv->alt_av, cm_id_priv);
 		if (ret)
-			goto error1;
+			goto out;
 	}
 	cm_id->service_id = param->service_id;
 	cm_id->service_mask = ~cpu_to_be64(0);
@@ -1465,7 +1473,7 @@ int ib_send_cm_req(struct ib_cm_id *cm_id,
 
 	ret = cm_alloc_msg(cm_id_priv, &cm_id_priv->msg);
 	if (ret)
-		goto error1;
+		goto out;
 
 	req_msg = (struct cm_req_msg *) cm_id_priv->msg->mad;
 	cm_format_req(req_msg, cm_id_priv, param);
@@ -1488,7 +1496,6 @@ int ib_send_cm_req(struct ib_cm_id *cm_id,
 	return 0;
 
 error2:	cm_free_msg(cm_id_priv->msg);
-error1:	kfree(cm_id_priv->timewait_info);
 out:	return ret;
 }
 EXPORT_SYMBOL(ib_send_cm_req);
@@ -1973,7 +1980,7 @@ static int cm_req_handler(struct cm_work *work)
 		pr_debug("%s: local_id %d, no listen_cm_id_priv\n", __func__,
 			 be32_to_cpu(cm_id->local_id));
 		ret = -EINVAL;
-		goto free_timeinfo;
+		goto destroy;
 	}
 
 	cm_id_priv->id.cm_handler = listen_cm_id_priv->id.cm_handler;
@@ -2057,8 +2064,6 @@ static int cm_req_handler(struct cm_work *work)
 rejected:
 	atomic_dec(&cm_id_priv->refcount);
 	cm_deref_id(listen_cm_id_priv);
-free_timeinfo:
-	kfree(cm_id_priv->timewait_info);
 destroy:
 	ib_destroy_cm_id(cm_id);
 	return ret;
Signature · 1 line
2.25.1
author maintainer
#117 lore raw

PATCH 116/206 drm/msm/a5xx: Always set an OPP supported hardware value

In reply to Sasha Levin

From: Jordan Crouse <[email protected]>

[ Upstream commit 0478b4fc5f37f4d494245fe7bcce3f531cf380e9 ]

If the opp table specifies opp-supported-hw as a property but the driver has not set a supported hardware value the OPP subsystem will reject all the table entries.

Set a "default" value that will match the default table entries but not conflict with any possible real bin values. Also fix a small memory leak and free the buffer allocated by nvmem_cell_read().

---
 drivers/gpu/drm/msm/adreno/a5xx_gpu.c | 27 ++++++++++++++++++++-------
 1 file changed, 20 insertions(+), 7 deletions(-)
drivers/gpu/drm/msm/adreno/a5xx_gpu.c +20 -7
index ba6f3c14495c0..dd298abc5f393 100644
@@ -1474,18 +1474,31 @@ static const struct adreno_gpu_funcs funcs = {
 static void check_speed_bin(struct device *dev)
 {
 	struct nvmem_cell *cell;
-	u32 bin, val;
+	u32 val;
+
+	/*
+	 * If the OPP table specifies a opp-supported-hw property then we have
+	 * to set something with dev_pm_opp_set_supported_hw() or the table
+	 * doesn't get populated so pick an arbitrary value that should
+	 * ensure the default frequencies are selected but not conflict with any
+	 * actual bins
+	 */
+	val = 0x80;
 
 	cell = nvmem_cell_get(dev, "speed_bin");
 
-	/* If a nvmem cell isn't defined, nothing to do */
-	if (IS_ERR(cell))
-		return;
+	if (!IS_ERR(cell)) {
+		void *buf = nvmem_cell_read(cell, NULL);
+
+		if (!IS_ERR(buf)) {
+			u8 bin = *((u8 *) buf);
 
-	bin = *((u32 *) nvmem_cell_read(cell, NULL));
-	nvmem_cell_put(cell);
+			val = (1 << bin);
+			kfree(buf);
+		}
 
-	val = (1 << bin);
+		nvmem_cell_put(cell);
+	}
 
 	dev_pm_opp_set_supported_hw(dev, &val, 1);
 }
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#113 lore raw

PATCH 112/206 nfsd: Don't add locks to closed or closing open stateids

In reply to Sasha Levin

From: Trond Myklebust <[email protected]>

[ Upstream commit a451b12311aa8c96c6f6e01c783a86995dc3ec6b ]

In NFSv4, the lock stateids are tied to the lockowner, and the open stateid, so that the action of closing the file also results in either an automatic loss of the locks, or an error of the form NFS4ERR_LOCKS_HELD.

In practice this means we must not add new locks to the open stateid after the close process has been invoked. In fact doing so, can result in the following panic:

kernel BUG at lib/list_debug.c:51!
invalid opcode: 0000 [#1] SMP NOPTI

 CPU: 2 PID: 1085 Comm: nfsd Not tainted 5.6.0-rc3+ #2
 Hardware name: VMware, Inc. VMware7,1/440BX Desktop Reference Platform, BIOS VMW71.00V.14410784.B64.1908150010 08/15/2019
 RIP: 0010:__list_del_entry_valid.cold+0x31/0x55
 Code: 1a 3d 9b e8 74 10 c2 ff 0f 0b 48 c7 c7 f0 1a 3d 9b e8 66 10 c2 ff 0f 0b 48 89 f2 48 89 fe 48 c7 c7 b0 1a 3d 9b e8 52 10 c2 ff <0f> 0b 48 89 fe 4c 89 c2 48 c7 c7 78 1a 3d 9b e8 3e 10 c2 ff 0f 0b
 RSP: 0018:ffffb296c1d47d90 EFLAGS: 00010246
 RAX: 0000000000000054 RBX: ffff8ba032456ec8 RCX: 0000000000000000
 RDX: 0000000000000000 RSI: ffff8ba039e99cc8 RDI: ffff8ba039e99cc8
 RBP: ffff8ba032456e60 R08: 0000000000000781 R09: 0000000000000003
 R10: 0000000000000000 R11: 0000000000000001 R12: ffff8ba009a4abe0
 R13: ffff8ba032456e8c R14: 0000000000000000 R15: ffff8ba00adb01d8
 FS:  0000000000000000(0000) GS:ffff8ba039e80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00007fb213f0b008 CR3: 00000001347de006 CR4: 00000000003606e0
 Call Trace:
  release_lock_stateid+0x2b/0x80 [nfsd]
  nfsd4_free_stateid+0x1e9/0x210 [nfsd]
  nfsd4_proc_compound+0x414/0x700 [nfsd]
  ? nfs4svc_decode_compoundargs+0x407/0x4c0 [nfsd]
  nfsd_dispatch+0xc1/0x200 [nfsd]
  svc_process_common+0x476/0x6f0 [sunrpc]
  ? svc_sock_secure_port+0x12/0x30 [sunrpc]
  ? svc_recv+0x313/0x9c0 [sunrpc]
  ? nfsd_svc+0x2d0/0x2d0 [nfsd]
  svc_process+0xd4/0x110 [sunrpc]
  nfsd+0xe3/0x140 [nfsd]
  kthread+0xf9/0x130
  ? nfsd_destroy+0x50/0x50 [nfsd]
  ? kthread_park+0x90/0x90
  ret_from_fork+0x1f/0x40

The fix is to ensure that lock creation tests for whether or not the open stateid is unhashed, and to fail if that is the case.

Fixes 659aefb68eca ("nfsd: Ensure we don't recognise lock stateids after freeing them")
---
 fs/nfsd/nfs4state.c | 73 ++++++++++++++++++++++++++-------------------
 1 file changed, 43 insertions(+), 30 deletions(-)
fs/nfsd/nfs4state.c +43 -30
index c24306af9758f..655079ae1dd1f 100644
@@ -471,6 +471,8 @@ find_any_file(struct nfs4_file *f)
 {
 	struct file *ret;
 
+	if (!f)
+		return NULL;
 	spin_lock(&f->fi_lock);
 	ret = __nfs4_get_fd(f, O_RDWR);
 	if (!ret) {
@@ -1207,6 +1209,12 @@ static void nfs4_put_stateowner(struct nfs4_stateowner *sop)
 	nfs4_free_stateowner(sop);
 }
 
+static bool
+nfs4_ol_stateid_unhashed(const struct nfs4_ol_stateid *stp)
+{
+	return list_empty(&stp->st_perfile);
+}
+
 static bool unhash_ol_stateid(struct nfs4_ol_stateid *stp)
 {
 	struct nfs4_file *fp = stp->st_stid.sc_file;
@@ -1274,9 +1282,11 @@ static bool unhash_lock_stateid(struct nfs4_ol_stateid *stp)
 {
 	lockdep_assert_held(&stp->st_stid.sc_client->cl_lock);
 
+	if (!unhash_ol_stateid(stp))
+		return false;
 	list_del_init(&stp->st_locks);
 	nfs4_unhash_stid(&stp->st_stid);
-	return unhash_ol_stateid(stp);
+	return true;
 }
 
 static void release_lock_stateid(struct nfs4_ol_stateid *stp)
@@ -1341,13 +1351,12 @@ static void release_open_stateid_locks(struct nfs4_ol_stateid *open_stp,
 static bool unhash_open_stateid(struct nfs4_ol_stateid *stp,
 				struct list_head *reaplist)
 {
-	bool unhashed;
-
 	lockdep_assert_held(&stp->st_stid.sc_client->cl_lock);
 
-	unhashed = unhash_ol_stateid(stp);
+	if (!unhash_ol_stateid(stp))
+		return false;
 	release_open_stateid_locks(stp, reaplist);
-	return unhashed;
+	return true;
 }
 
 static void release_open_stateid(struct nfs4_ol_stateid *stp)
@@ -5774,21 +5783,21 @@ alloc_init_lock_stateowner(unsigned int strhashval, struct nfs4_client *clp,
 }
 
 static struct nfs4_ol_stateid *
-find_lock_stateid(struct nfs4_lockowner *lo, struct nfs4_file *fp)
+find_lock_stateid(const struct nfs4_lockowner *lo,
+		  const struct nfs4_ol_stateid *ost)
 {
 	struct nfs4_ol_stateid *lst;
-	struct nfs4_client *clp = lo->lo_owner.so_client;
 
-	lockdep_assert_held(&clp->cl_lock);
+	lockdep_assert_held(&ost->st_stid.sc_client->cl_lock);
 
-	list_for_each_entry(lst, &lo->lo_owner.so_stateids, st_perstateowner) {
-		if (lst->st_stid.sc_type != NFS4_LOCK_STID)
-			continue;
-		if (lst->st_stid.sc_file == fp) {
-			refcount_inc(&lst->st_stid.sc_count);
-			return lst;
+	/* If ost is not hashed, ost->st_locks will not be valid */
+	if (!nfs4_ol_stateid_unhashed(ost))
+		list_for_each_entry(lst, &ost->st_locks, st_locks) {
+			if (lst->st_stateowner == &lo->lo_owner) {
+				refcount_inc(&lst->st_stid.sc_count);
+				return lst;
+			}
 		}
-	}
 	return NULL;
 }
 
@@ -5804,11 +5813,11 @@ init_lock_stateid(struct nfs4_ol_stateid *stp, struct nfs4_lockowner *lo,
 	mutex_lock_nested(&stp->st_mutex, OPEN_STATEID_MUTEX);
 retry:
 	spin_lock(&clp->cl_lock);
-	spin_lock(&fp->fi_lock);
-	retstp = find_lock_stateid(lo, fp);
+	if (nfs4_ol_stateid_unhashed(open_stp))
+		goto out_close;
+	retstp = find_lock_stateid(lo, open_stp);
 	if (retstp)
-		goto out_unlock;
-
+		goto out_found;
 	refcount_inc(&stp->st_stid.sc_count);
 	stp->st_stid.sc_type = NFS4_LOCK_STID;
 	stp->st_stateowner = nfs4_get_stateowner(&lo->lo_owner);
@@ -5817,22 +5826,26 @@ retry:
 	stp->st_access_bmap = 0;
 	stp->st_deny_bmap = open_stp->st_deny_bmap;
 	stp->st_openstp = open_stp;
+	spin_lock(&fp->fi_lock);
 	list_add(&stp->st_locks, &open_stp->st_locks);
 	list_add(&stp->st_perstateowner, &lo->lo_owner.so_stateids);
 	list_add(&stp->st_perfile, &fp->fi_stateids);
-out_unlock:
 	spin_unlock(&fp->fi_lock);
 	spin_unlock(&clp->cl_lock);
-	if (retstp) {
-		if (nfsd4_lock_ol_stateid(retstp) != nfs_ok) {
-			nfs4_put_stid(&retstp->st_stid);
-			goto retry;
-		}
-		/* To keep mutex tracking happy */
-		mutex_unlock(&stp->st_mutex);
-		stp = retstp;
-	}
 	return stp;
+out_found:
+	spin_unlock(&clp->cl_lock);
+	if (nfsd4_lock_ol_stateid(retstp) != nfs_ok) {
+		nfs4_put_stid(&retstp->st_stid);
+		goto retry;
+	}
+	/* To keep mutex tracking happy */
+	mutex_unlock(&stp->st_mutex);
+	return retstp;
+out_close:
+	spin_unlock(&clp->cl_lock);
+	mutex_unlock(&stp->st_mutex);
+	return NULL;
 }
 
 static struct nfs4_ol_stateid *
@@ -5847,7 +5860,7 @@ find_or_create_lock_stateid(struct nfs4_lockowner *lo, struct nfs4_file *fi,
 
 	*new = false;
 	spin_lock(&clp->cl_lock);
-	lst = find_lock_stateid(lo, fi);
+	lst = find_lock_stateid(lo, ost);
 	spin_unlock(&clp->cl_lock);
 	if (lst != NULL) {
 		if (nfsd4_lock_ol_stateid(lst) == nfs_ok)
Signature · 1 line
2.25.1
author maintainer
#119 lore raw

PATCH 118/206 thermal: rcar_thermal: Handle probe error gracefully

In reply to Sasha Levin

From: Niklas Söderlund <[email protected]>

[ Upstream commit 39056e8a989ef52486e063e34b4822b341e47b0e ]

If the common register memory resource is not available the driver needs to fail gracefully to disable PM. Instead of returning the error directly store it in ret and use the already existing error path.

---
 drivers/thermal/rcar_thermal.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/thermal/rcar_thermal.c +4 -2
index 4dc30e7890f6c..140386d7c75a3 100644
@@ -505,8 +505,10 @@ static int rcar_thermal_probe(struct platform_device *pdev)
 			res = platform_get_resource(pdev, IORESOURCE_MEM,
 						    mres++);
 			common->base = devm_ioremap_resource(dev, res);
-			if (IS_ERR(common->base))
-				return PTR_ERR(common->base);
+			if (IS_ERR(common->base)) {
+				ret = PTR_ERR(common->base);
+				goto error_unregister;
+			}
 
 			idle = 0; /* polling delay is not needed */
 		}
Signature · 1 line
2.25.1
author maintainer
#123 lore raw

PATCH 122/206 serial: 8250: 8250_omap: Terminate DMA before pushing data on RX timeout

In reply to Sasha Levin

From: Vignesh Raghavendra <[email protected]>

[ Upstream commit 7cf4df30a98175033e9849f7f16c46e96ba47f41 ]

Terminate and flush DMA internal buffers, before pushing RX data to higher layer. Otherwise, this will lead to data corruption, as driver would end up pushing stale buffer data to higher layer while actual data is still stuck inside DMA hardware and has yet not arrived at the memory.
While at that, replace deprecated dmaengine_terminate_all() with dmaengine_terminate_async().

---
 drivers/tty/serial/8250/8250_omap.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/tty/serial/8250/8250_omap.c +4 -2
index a7e555e413a69..cbd006fb7fbb9 100644
@@ -781,7 +781,10 @@ static void __dma_rx_do_complete(struct uart_8250_port *p)
 	dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
 
 	count = dma->rx_size - state.residue;
-
+	if (count < dma->rx_size)
+		dmaengine_terminate_async(dma->rxchan);
+	if (!count)
+		goto unlock;
 	ret = tty_insert_flip_string(tty_port, dma->rx_buf, count);
 
 	p->port.icount.rx += ret;
@@ -843,7 +846,6 @@ static void omap_8250_rx_dma_flush(struct uart_8250_port *p)
 	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
 
 	__dma_rx_do_complete(p);
-	dmaengine_terminate_all(dma->rxchan);
 }
 
 static int omap_8250_rx_dma(struct uart_8250_port *p)
Signature · 1 line
2.25.1
author maintainer
#127 lore raw

PATCH 126/206 nvme-multipath: do not reset on unknown status

In reply to Sasha Levin

From: John Meneghini <[email protected]>

[ Upstream commit 764e9332098c0e60251386a507fe46ac91276120 ]

The nvme multipath error handling defaults to controller reset if the error is unknown. There are, however, no existing nvme status codes that indicate a reset should be used, and resetting causes unnecessary disruption to the rest of IO.

Change nvme's error handling to first check if failover should happen. If not, let the normal error handling take over rather than reset the controller.

---
 drivers/nvme/host/core.c      |  5 +----
 drivers/nvme/host/multipath.c | 21 +++++++++------------
 drivers/nvme/host/nvme.h      |  5 +++--
 3 files changed, 13 insertions(+), 18 deletions(-)
drivers/nvme/host/core.c +1 -4
index 0d60f2f8f3eec..4b182ac15687e 100644
@@ -255,11 +255,8 @@ void nvme_complete_rq(struct request *req)
 	trace_nvme_complete_rq(req);
 
 	if (unlikely(status != BLK_STS_OK && nvme_req_needs_retry(req))) {
-		if ((req->cmd_flags & REQ_NVME_MPATH) &&
-		    blk_path_error(status)) {
-			nvme_failover_req(req);
+		if ((req->cmd_flags & REQ_NVME_MPATH) && nvme_failover_req(req))
 			return;
-		}
 
 		if (!blk_queue_dying(req->q)) {
 			nvme_req(req)->retries++;
drivers/nvme/host/multipath.c +9 -12
index 2e63c1106030b..e71075338ff5c 100644
@@ -73,17 +73,12 @@ void nvme_set_disk_name(char *disk_name, struct nvme_ns *ns,
 	}
 }
 
-void nvme_failover_req(struct request *req)
+bool nvme_failover_req(struct request *req)
 {
 	struct nvme_ns *ns = req->q->queuedata;
 	u16 status = nvme_req(req)->status;
 	unsigned long flags;
 
-	spin_lock_irqsave(&ns->head->requeue_lock, flags);
-	blk_steal_bios(&ns->head->requeue_list, req);
-	spin_unlock_irqrestore(&ns->head->requeue_lock, flags);
-	blk_mq_end_request(req, 0);
-
 	switch (status & 0x7ff) {
 	case NVME_SC_ANA_TRANSITION:
 	case NVME_SC_ANA_INACCESSIBLE:
@@ -111,15 +106,17 @@ void nvme_failover_req(struct request *req)
 		nvme_mpath_clear_current_path(ns);
 		break;
 	default:
-		/*
-		 * Reset the controller for any non-ANA error as we don't know
-		 * what caused the error.
-		 */
-		nvme_reset_ctrl(ns->ctrl);
-		break;
+		/* This was a non-ANA error so follow the normal error path. */
+		return false;
 	}
 
+	spin_lock_irqsave(&ns->head->requeue_lock, flags);
+	blk_steal_bios(&ns->head->requeue_list, req);
+	spin_unlock_irqrestore(&ns->head->requeue_lock, flags);
+	blk_mq_end_request(req, 0);
+
 	kblockd_schedule_work(&ns->head->requeue_work);
+	return true;
 }
 
 void nvme_kick_requeue_lists(struct nvme_ctrl *ctrl)
drivers/nvme/host/nvme.h +3 -2
index cc4273f119894..31c1496f938fb 100644
@@ -477,7 +477,7 @@ void nvme_mpath_wait_freeze(struct nvme_subsystem *subsys);
 void nvme_mpath_start_freeze(struct nvme_subsystem *subsys);
 void nvme_set_disk_name(char *disk_name, struct nvme_ns *ns,
 			struct nvme_ctrl *ctrl, int *flags);
-void nvme_failover_req(struct request *req);
+bool nvme_failover_req(struct request *req);
 void nvme_kick_requeue_lists(struct nvme_ctrl *ctrl);
 int nvme_mpath_alloc_disk(struct nvme_ctrl *ctrl,struct nvme_ns_head *head);
 void nvme_mpath_add_disk(struct nvme_ns *ns, struct nvme_id_ns *id);
@@ -521,8 +521,9 @@ static inline void nvme_set_disk_name(char *disk_name, struct nvme_ns *ns,
 	sprintf(disk_name, "nvme%dn%d", ctrl->instance, ns->head->instance);
 }
 
-static inline void nvme_failover_req(struct request *req)
+static inline bool nvme_failover_req(struct request *req)
 {
+	return false;
 }
 static inline void nvme_kick_requeue_lists(struct nvme_ctrl *ctrl)
 {
Signature · 1 line
2.25.1
author maintainer
#128 lore raw

PATCH 127/206 nvme: Fix controller creation races with teardown flow

In reply to Sasha Levin

From: Israel Rukshin <[email protected]>

[ Upstream commit ce1518139e6976cf19c133b555083354fdb629b8 ]

Calling nvme_sysfs_delete() when the controller is in the middle of creation may cause several bugs. If the controller is in NEW state we remove delete_controller file and don't delete the controller. The user will not be able to use nvme disconnect command on that controller again, although the controller may be active. Other bugs may happen if the controller is in the middle of create_ctrl callback and nvme_do_delete_ctrl() starts. For example, freeing I/O tagset at nvme_do_delete_ctrl() before it was allocated at create_ctrl callback.

To fix all those races don't allow the user to delete the controller before it was fully created.

---
 drivers/nvme/host/core.c | 5 +++++
 drivers/nvme/host/nvme.h | 1 +
 2 files changed, 6 insertions(+)
drivers/nvme/host/core.c +5 -0
index 4b182ac15687e..faa7feebb6095 100644
@@ -2856,6 +2856,10 @@ static ssize_t nvme_sysfs_delete(struct device *dev,
 {
 	struct nvme_ctrl *ctrl = dev_get_drvdata(dev);
 
+	/* Can't delete non-created controllers */
+	if (!ctrl->created)
+		return -EBUSY;
+
 	if (device_remove_file_self(dev, attr))
 		nvme_delete_ctrl_sync(ctrl);
 	return count;
@@ -3576,6 +3580,7 @@ void nvme_start_ctrl(struct nvme_ctrl *ctrl)
 		queue_work(nvme_wq, &ctrl->async_event_work);
 		nvme_start_queues(ctrl);
 	}
+	ctrl->created = true;
 }
 EXPORT_SYMBOL_GPL(nvme_start_ctrl);
 
drivers/nvme/host/nvme.h +1 -0
index 31c1496f938fb..a70b997060e68 100644
@@ -206,6 +206,7 @@ struct nvme_ctrl {
 	struct nvme_command ka_cmd;
 	struct work_struct fw_act_work;
 	unsigned long events;
+	bool created;
 
 #ifdef CONFIG_NVME_MULTIPATH
 	/* asymmetric namespace access: */
Signature · 1 line
2.25.1
author maintainer
#134 lore raw

PATCH 132/206 PCI: Use ioremap(), not phys_to_virt() for platform ROM

In reply to Sasha Levin

From: Mikel Rychliski <[email protected]>

[ Upstream commit 72e0ef0e5f067fd991f702f0b2635d911d0cf208 ]

On some EFI systems, the video BIOS is provided by the EFI firmware. The boot stub code stores the physical address of the ROM image in pdev->rom. Currently we attempt to access this pointer using phys_to_virt(), which doesn't work with CONFIG_HIGHMEM.

On these systems, attempting to load the radeon module on a x86_32 kernel can result in the following:

  BUG: unable to handle page fault for address: 3e8ed03c
  #PF: supervisor read access in kernel mode
  #PF: error_code(0x0000) - not-present page
  *pde = 00000000
  Oops: 0000 [#1] PREEMPT SMP
  CPU: 0 PID: 317 Comm: systemd-udevd Not tainted 5.6.0-rc3-next-20200228 #2
  Hardware name: Apple Computer, Inc. MacPro1,1/Mac-F4208DC8, BIOS     MP11.88Z.005C.B08.0707021221 07/02/07
  EIP: radeon_get_bios+0x5ed/0xe50 [radeon]
  Code: 00 00 84 c0 0f 85 12 fd ff ff c7 87 64 01 00 00 00 00 00 00 8b 47 08 8b 55 b0 e8 1e 83 e1 d6 85 c0 74 1a 8b 55 c0 85 d2 74 13 <80> 38 55 75 0e 80 78 01 aa 0f 84 a4 03 00 00 8d 74 26 00 68 dc 06
  EAX: 3e8ed03c EBX: 00000000 ECX: 3e8ed03c EDX: 00010000
  ESI: 00040000 EDI: eec04000 EBP: eef3fc60 ESP: eef3fbe0
  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010206
  CR0: 80050033 CR2: 3e8ed03c CR3: 2ec77000 CR4: 000006d0
  Call Trace:
   r520_init+0x26/0x240 [radeon]
   radeon_device_init+0x533/0xa50 [radeon]
   radeon_driver_load_kms+0x80/0x220 [radeon]
   drm_dev_register+0xa7/0x180 [drm]
   radeon_pci_probe+0x10f/0x1a0 [radeon]
   pci_device_probe+0xd4/0x140

Fix the issue by updating all drivers which can access a platform provided ROM. Instead of calling the helper function pci_platform_rom() which uses phys_to_virt(), call ioremap() directly on the pdev->rom.

radeon_read_platform_bios() previously directly accessed an __iomem pointer. Avoid this by calling memcpy_fromio() instead of kmemdup().

pci_platform_rom() now has no remaining callers, so remove it.

---
 drivers/gpu/drm/amd/amdgpu/amdgpu_bios.c      | 31 +++++++++++--------
 .../drm/nouveau/nvkm/subdev/bios/shadowpci.c  | 17 ++++++++--
 drivers/gpu/drm/radeon/radeon_bios.c          | 30 +++++++++++-------
 drivers/pci/rom.c                             | 17 ----------
 include/linux/pci.h                           |  1 -
 5 files changed, 52 insertions(+), 44 deletions(-)
drivers/gpu/drm/amd/amdgpu/amdgpu_bios.c +18 -13
index a5df80d50d447..6cf3dd5edffda 100644
@@ -191,30 +191,35 @@ static bool amdgpu_read_bios_from_rom(struct amdgpu_device *adev)
 
 static bool amdgpu_read_platform_bios(struct amdgpu_device *adev)
 {
-	uint8_t __iomem *bios;
-	size_t size;
+	phys_addr_t rom = adev->pdev->rom;
+	size_t romlen = adev->pdev->romlen;
+	void __iomem *bios;
 
 	adev->bios = NULL;
 
-	bios = pci_platform_rom(adev->pdev, &size);
-	if (!bios) {
+	if (!rom || romlen == 0)
 		return false;
-	}
 
-	adev->bios = kzalloc(size, GFP_KERNEL);
-	if (adev->bios == NULL)
+	adev->bios = kzalloc(romlen, GFP_KERNEL);
+	if (!adev->bios)
 		return false;
 
-	memcpy_fromio(adev->bios, bios, size);
+	bios = ioremap(rom, romlen);
+	if (!bios)
+		goto free_bios;
 
-	if (!check_atom_bios(adev->bios, size)) {
-		kfree(adev->bios);
-		return false;
-	}
+	memcpy_fromio(adev->bios, bios, romlen);
+	iounmap(bios);
 
-	adev->bios_size = size;
+	if (!check_atom_bios(adev->bios, romlen))
+		goto free_bios;
+
+	adev->bios_size = romlen;
 
 	return true;
+free_bios:
+	kfree(adev->bios);
+	return false;
 }
 
 #ifdef CONFIG_ACPI
drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowpci.c +15 -2
index 9b91da09dc5f8..8d9812a51ef63 100644
@@ -101,9 +101,13 @@ platform_init(struct nvkm_bios *bios, const char *name)
 	else
 		return ERR_PTR(-ENODEV);
 
+	if (!pdev->rom || pdev->romlen == 0)
+		return ERR_PTR(-ENODEV);
+
 	if ((priv = kmalloc(sizeof(*priv), GFP_KERNEL))) {
+		priv->size = pdev->romlen;
 		if (ret = -ENODEV,
-		    (priv->rom = pci_platform_rom(pdev, &priv->size)))
+		    (priv->rom = ioremap(pdev->rom, pdev->romlen)))
 			return priv;
 		kfree(priv);
 	}
@@ -111,11 +115,20 @@ platform_init(struct nvkm_bios *bios, const char *name)
 	return ERR_PTR(ret);
 }
 
+static void
+platform_fini(void *data)
+{
+	struct priv *priv = data;
+
+	iounmap(priv->rom);
+	kfree(priv);
+}
+
 const struct nvbios_source
 nvbios_platform = {
 	.name = "PLATFORM",
 	.init = platform_init,
-	.fini = (void(*)(void *))kfree,
+	.fini = platform_fini,
 	.read = pcirom_read,
 	.rw = true,
 };
drivers/gpu/drm/radeon/radeon_bios.c +19 -11
index 04c0ed41374f1..dd0528cf98183 100644
@@ -104,25 +104,33 @@ static bool radeon_read_bios(struct radeon_device *rdev)
 
 static bool radeon_read_platform_bios(struct radeon_device *rdev)
 {
-	uint8_t __iomem *bios;
-	size_t size;
+	phys_addr_t rom = rdev->pdev->rom;
+	size_t romlen = rdev->pdev->romlen;
+	void __iomem *bios;
 
 	rdev->bios = NULL;
 
-	bios = pci_platform_rom(rdev->pdev, &size);
-	if (!bios) {
+	if (!rom || romlen == 0)
 		return false;
-	}
 
-	if (size == 0 || bios[0] != 0x55 || bios[1] != 0xaa) {
+	rdev->bios = kzalloc(romlen, GFP_KERNEL);
+	if (!rdev->bios)
 		return false;
-	}
-	rdev->bios = kmemdup(bios, size, GFP_KERNEL);
-	if (rdev->bios == NULL) {
-		return false;
-	}
+
+	bios = ioremap(rom, romlen);
+	if (!bios)
+		goto free_bios;
+
+	memcpy_fromio(rdev->bios, bios, romlen);
+	iounmap(bios);
+
+	if (rdev->bios[0] != 0x55 || rdev->bios[1] != 0xaa)
+		goto free_bios;
 
 	return true;
+free_bios:
+	kfree(rdev->bios);
+	return false;
 }
 
 #ifdef CONFIG_ACPI
drivers/pci/rom.c +0 -17
index 137bf0cee897c..8fc9a4e911e3a 100644
@@ -195,20 +195,3 @@ void pci_unmap_rom(struct pci_dev *pdev, void __iomem *rom)
 		pci_disable_rom(pdev);
 }
 EXPORT_SYMBOL(pci_unmap_rom);
-
-/**
- * pci_platform_rom - provides a pointer to any ROM image provided by the
- * platform
- * @pdev: pointer to pci device struct
- * @size: pointer to receive size of pci window over ROM
- */
-void __iomem *pci_platform_rom(struct pci_dev *pdev, size_t *size)
-{
-	if (pdev->rom && pdev->romlen) {
-		*size = pdev->romlen;
-		return phys_to_virt((phys_addr_t)pdev->rom);
-	}
-
-	return NULL;
-}
-EXPORT_SYMBOL(pci_platform_rom);
include/linux/pci.h +0 -1
index 2517492dd1855..2fda9893962d1 100644
@@ -1144,7 +1144,6 @@ int pci_enable_rom(struct pci_dev *pdev);
 void pci_disable_rom(struct pci_dev *pdev);
 void __iomem __must_check *pci_map_rom(struct pci_dev *pdev, size_t *size);
 void pci_unmap_rom(struct pci_dev *pdev, void __iomem *rom);
-void __iomem __must_check *pci_platform_rom(struct pci_dev *pdev, size_t *size);
 
 /* Power management related routines */
 int pci_save_state(struct pci_dev *dev);
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#139 lore raw

PATCH 137/206 mm/kmemleak.c: use address-of operator on section symbols

In reply to Sasha Levin

From: Nathan Chancellor <[email protected]>

[ Upstream commit b0d14fc43d39203ae025f20ef4d5d25d9ccf4be1 ]

Clang warns:

mm/kmemleak.c:1955:28: warning: array comparison always evaluates to a constant [-Wtautological-compare]

        if (__start_ro_after_init < _sdata || __end_ro_after_init > _edata)
                                  ^
  mm/kmemleak.c:1955:60: warning: array comparison always evaluates to a constant [-Wtautological-compare]
        if (__start_ro_after_init < _sdata || __end_ro_after_init > _edata)

These are not true arrays, they are linker defined symbols, which are just addresses. Using the address of operator silences the warning and does not change the resulting assembly with either clang/ld.lld or gcc/ld (tested with diff + objdump -Dr).

---
 mm/kmemleak.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
mm/kmemleak.c +1 -1
index 5eeabece0c178..f54734abf9466 100644
@@ -2039,7 +2039,7 @@ void __init kmemleak_init(void)
 	create_object((unsigned long)__bss_start, __bss_stop - __bss_start,
 		      KMEMLEAK_GREY, GFP_ATOMIC);
 	/* only register .data..ro_after_init if not within .data */
-	if (__start_ro_after_init < _sdata || __end_ro_after_init > _edata)
+	if (&__start_ro_after_init < &_sdata || &__end_ro_after_init > &_edata)
 		create_object((unsigned long)__start_ro_after_init,
 			      __end_ro_after_init - __start_ro_after_init,
 			      KMEMLEAK_GREY, GFP_ATOMIC);
Signature · 1 line
2.25.1
author maintainer
#135 lore raw

PATCH 133/206 ubifs: Fix out-of-bounds memory access caused by abnormal value of node_len

In reply to Sasha Levin

From: Liu Song <[email protected]>

[ Upstream commit acc5af3efa303d5f36cc8c0f61716161f6ca1384 ]

In “ubifs_check_node”, when the value of "node_len" is abnormal, the code will goto label of "out_len" for execution. Then, in the following "ubifs_dump_node", if inode type is "UBIFS_DATA_NODE", in "print_hex_dump", an out-of-bounds access may occur due to the wrong "ch->len".

Therefore, when the value of "node_len" is abnormal, data length should to be adjusted to a reasonable safe range. At this time, structured data is not credible, so dump the corrupted data directly for analysis.

---
 fs/ubifs/io.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)
fs/ubifs/io.c +14 -2
index 099bec94b8207..fab29f899f913 100644
@@ -237,7 +237,7 @@ int ubifs_is_mapped(const struct ubifs_info *c, int lnum)
 int ubifs_check_node(const struct ubifs_info *c, const void *buf, int lnum,
 		     int offs, int quiet, int must_chk_crc)
 {
-	int err = -EINVAL, type, node_len;
+	int err = -EINVAL, type, node_len, dump_node = 1;
 	uint32_t crc, node_crc, magic;
 	const struct ubifs_ch *ch = buf;
 
@@ -290,10 +290,22 @@ int ubifs_check_node(const struct ubifs_info *c, const void *buf, int lnum,
 out_len:
 	if (!quiet)
 		ubifs_err(c, "bad node length %d", node_len);
+	if (type == UBIFS_DATA_NODE && node_len > UBIFS_DATA_NODE_SZ)
+		dump_node = 0;
 out:
 	if (!quiet) {
 		ubifs_err(c, "bad node at LEB %d:%d", lnum, offs);
-		ubifs_dump_node(c, buf);
+		if (dump_node) {
+			ubifs_dump_node(c, buf);
+		} else {
+			int safe_len = min3(node_len, c->leb_size - offs,
+				(int)UBIFS_MAX_DATA_NODE_SZ);
+			pr_err("\tprevent out-of-bounds memory access\n");
+			pr_err("\ttruncated data node length      %d\n", safe_len);
+			pr_err("\tcorrupted data node:\n");
+			print_hex_dump(KERN_ERR, "\t", DUMP_PREFIX_OFFSET, 32, 1,
+					buf, safe_len, 0);
+		}
 		dump_stack();
 	}
 	return err;
Signature · 1 line
2.25.1
author maintainer
#140 lore raw

PATCH 138/206 mm/filemap.c: clear page error before actual read

In reply to Sasha Levin

From: Xianting Tian <[email protected]>

[ Upstream commit faffdfa04fa11ccf048cebdde73db41ede0679e0 ]

Mount failure issue happens under the scenario: Application forked dozens of threads to mount the same number of cramfs images separately in docker, but several mounts failed with high probability. Mount failed due to the checking result of the page(read from the superblock of loop dev) is not uptodate after wait_on_page_locked(page) returned in function cramfs_read:

   wait_on_page_locked(page);
   if (!PageUptodate(page)) {
      ...
   }

The reason of the checking result of the page not uptodate: systemd-udevd read the loopX dev before mount, because the status of loopX is Lo_unbound at this time, so loop_make_request directly trigger the calling of io_end handler end_buffer_async_read, which called SetPageError(page). So It caused the page can't be set to uptodate in function end_buffer_async_read:

   if(page_uptodate && !PageError(page)) {
      SetPageUptodate(page);
   }

Then mount operation is performed, it used the same page which is just accessed by systemd-udevd above, Because this page is not uptodate, it will launch a actual read via submit_bh, then wait on this page by calling wait_on_page_locked(page). When the I/O of the page done, io_end handler end_buffer_async_read is called, because no one cleared the page error(during the whole read path of mount), which is caused by systemd-udevd reading, so this page is still in "PageError" status, which can't be set to uptodate in function end_buffer_async_read, then caused mount failure.

But sometimes mount succeed even through systemd-udeved read loopX dev just before, The reason is systemd-udevd launched other loopX read just between step 3.1 and 3.2, the steps as below:

1, loopX dev default status is Lo_unbound;
2, systemd-udved read loopX dev (page is set to PageError); 3, mount operation
1) set loopX status to Lo_bound; ==>systemd-udevd read loopX dev<==
2) read loopX dev(page has no error)
3) mount succeed

As the loopX dev status is set to Lo_bound after step 3.1, so the other loopX dev read by systemd-udevd will go through the whole I/O stack, part of the call trace as below:

   SYS_read
      vfs_read
          do_sync_read
              blkdev_aio_read
                 generic_file_aio_read
                     do_generic_file_read:
                        ClearPageError(page);
                        mapping->a_ops->readpage(filp, page);

here, mapping->a_ops->readpage() is blkdev_readpage. In latest kernel, some function name changed, the call trace as below:

blkdev_read_iter

      generic_file_read_iter
         generic_file_buffered_read:
            /*
             * A previous I/O error may have been due to temporary
             * failures, eg. mutipath errors.
             * Pg_error will be set again if readpage fails.
             */
            ClearPageError(page);
            /* Start the actual read. The read will unlock the page*/
            error=mapping->a_ops->readpage(flip, page);

We can see ClearPageError(page) is called before the actual read, then the read in step 3.2 succeed.

This patch is to add the calling of ClearPageError just before the actual read of read path of cramfs mount. Without the patch, the call trace as below when performing cramfs mount:

   do_mount
      cramfs_read
         cramfs_blkdev_read
            read_cache_page
               do_read_cache_page:
                  filler(data, page);
                  or
                  mapping->a_ops->readpage(data, page);

With the patch, the call trace as below when performing mount:

   do_mount
      cramfs_read
         cramfs_blkdev_read
            read_cache_page:
               do_read_cache_page:
                  ClearPageError(page); <== new add
                  filler(data, page);
                  or
                  mapping->a_ops->readpage(data, page);

With the patch, mount operation trigger the calling of ClearPageError(page) before the actual read, the page has no error if no additional page error happen when I/O done.

---
 mm/filemap.c | 8 ++++++++
 1 file changed, 8 insertions(+)
mm/filemap.c +8 -0
index 45f1c6d73b5b0..f2e777003b901 100644
@@ -2889,6 +2889,14 @@ filler:
 		unlock_page(page);
 		goto out;
 	}
+
+	/*
+	 * A previous I/O error may have been due to temporary
+	 * failures.
+	 * Clear page error before actual read, PG_error will be
+	 * set again if read page fails.
+	 */
+	ClearPageError(page);
 	goto filler;
 
 out:
Signature · 1 line
2.25.1
author maintainer
#141 lore raw

PATCH 139/206 mm/vmscan.c: fix data races using kswapd_classzone_idx

In reply to Sasha Levin

From: Qian Cai <[email protected]>

[ Upstream commit 5644e1fbbfe15ad06785502bbfe5751223e5841d ]

pgdat->kswapd_classzone_idx could be accessed concurrently in wakeup_kswapd(). Plain writes and reads without any lock protection result in data races. Fix them by adding a pair of READ|WRITE_ONCE() as well as saving a branch (compilers might well optimize the original code in an unintentional way anyway). While at it, also take care of pgdat->kswapd_order and non-kswapd threads in allow_direct_reclaim(). The data races were reported by KCSAN,

 BUG: KCSAN: data-race in wakeup_kswapd / wakeup_kswapd

write to 0xffff9f427ffff2dc of 4 bytes by task 7454 on cpu 13:

  wakeup_kswapd+0xf1/0x400
  wakeup_kswapd at mm/vmscan.c:3967
  wake_all_kswapds+0x59/0xc0
  wake_all_kswapds at mm/page_alloc.c:4241
  __alloc_pages_slowpath+0xdcc/0x1290
  __alloc_pages_slowpath at mm/page_alloc.c:4512
  __alloc_pages_nodemask+0x3bb/0x450
  alloc_pages_vma+0x8a/0x2c0
  do_anonymous_page+0x16e/0x6f0
  __handle_mm_fault+0xcd5/0xd40
  handle_mm_fault+0xfc/0x2f0
  do_page_fault+0x263/0x6f9
  page_fault+0x34/0x40

1 lock held by mtest01/7454:
#0: ffff9f425afe8808 (&mm->mmap_sem#2){++++}, at:

 do_page_fault+0x143/0x6f9
 do_user_addr_fault at arch/x86/mm/fault.c:1405
 (inlined by) do_page_fault at arch/x86/mm/fault.c:1539
 irq event stamp: 6944085
 count_memcg_event_mm+0x1a6/0x270
 count_memcg_event_mm+0x119/0x270
 __do_softirq+0x34c/0x57c
 irq_exit+0xa2/0xc0

read to 0xffff9f427ffff2dc of 4 bytes by task 7472 on cpu 38:

  wakeup_kswapd+0xc8/0x400
  wake_all_kswapds+0x59/0xc0
  __alloc_pages_slowpath+0xdcc/0x1290
  __alloc_pages_nodemask+0x3bb/0x450
  alloc_pages_vma+0x8a/0x2c0
  do_anonymous_page+0x16e/0x6f0
  __handle_mm_fault+0xcd5/0xd40
  handle_mm_fault+0xfc/0x2f0
  do_page_fault+0x263/0x6f9
  page_fault+0x34/0x40

1 lock held by mtest01/7472:
#0: ffff9f425a9ac148 (&mm->mmap_sem#2){++++}, at:

 do_page_fault+0x143/0x6f9
 irq event stamp: 6793561
 count_memcg_event_mm+0x1a6/0x270
 count_memcg_event_mm+0x119/0x270
 __do_softirq+0x34c/0x57c
 irq_exit+0xa2/0xc0

 BUG: KCSAN: data-race in kswapd / wakeup_kswapd

write to 0xffff90973ffff2dc of 4 bytes by task 820 on cpu 6:

  kswapd+0x27c/0x8d0
  kthread+0x1e0/0x200
  ret_from_fork+0x27/0x50

read to 0xffff90973ffff2dc of 4 bytes by task 6299 on cpu 0:

  wakeup_kswapd+0xf3/0x450
  wake_all_kswapds+0x59/0xc0
  __alloc_pages_slowpath+0xdcc/0x1290
  __alloc_pages_nodemask+0x3bb/0x450
  alloc_pages_vma+0x8a/0x2c0
  do_anonymous_page+0x170/0x700
  __handle_mm_fault+0xc9f/0xd00
  handle_mm_fault+0xfc/0x2f0
  do_page_fault+0x263/0x6f9
  page_fault+0x34/0x40
---
 mm/vmscan.c | 45 ++++++++++++++++++++++++++-------------------
 1 file changed, 26 insertions(+), 19 deletions(-)
mm/vmscan.c +26 -19
index bc2ecd43251ad..da09b741d08a0 100644
@@ -3101,8 +3101,9 @@ static bool allow_direct_reclaim(pg_data_t *pgdat)
 
 	/* kswapd must be awake if processes are being throttled */
 	if (!wmark_ok && waitqueue_active(&pgdat->kswapd_wait)) {
-		pgdat->kswapd_classzone_idx = min(pgdat->kswapd_classzone_idx,
-						(enum zone_type)ZONE_NORMAL);
+		if (READ_ONCE(pgdat->kswapd_classzone_idx) > ZONE_NORMAL)
+			WRITE_ONCE(pgdat->kswapd_classzone_idx, ZONE_NORMAL);
+
 		wake_up_interruptible(&pgdat->kswapd_wait);
 	}
 
@@ -3618,9 +3619,9 @@ out:
 static enum zone_type kswapd_classzone_idx(pg_data_t *pgdat,
 					   enum zone_type prev_classzone_idx)
 {
-	if (pgdat->kswapd_classzone_idx == MAX_NR_ZONES)
-		return prev_classzone_idx;
-	return pgdat->kswapd_classzone_idx;
+	enum zone_type curr_idx = READ_ONCE(pgdat->kswapd_classzone_idx);
+
+	return curr_idx == MAX_NR_ZONES ? prev_classzone_idx : curr_idx;
 }
 
 static void kswapd_try_to_sleep(pg_data_t *pgdat, int alloc_order, int reclaim_order,
@@ -3664,8 +3665,11 @@ static void kswapd_try_to_sleep(pg_data_t *pgdat, int alloc_order, int reclaim_o
 		 * the previous request that slept prematurely.
 		 */
 		if (remaining) {
-			pgdat->kswapd_classzone_idx = kswapd_classzone_idx(pgdat, classzone_idx);
-			pgdat->kswapd_order = max(pgdat->kswapd_order, reclaim_order);
+			WRITE_ONCE(pgdat->kswapd_classzone_idx,
+				   kswapd_classzone_idx(pgdat, classzone_idx));
+
+			if (READ_ONCE(pgdat->kswapd_order) < reclaim_order)
+				WRITE_ONCE(pgdat->kswapd_order, reclaim_order);
 		}
 
 		finish_wait(&pgdat->kswapd_wait, &wait);
@@ -3747,12 +3751,12 @@ static int kswapd(void *p)
 	tsk->flags |= PF_MEMALLOC | PF_SWAPWRITE | PF_KSWAPD;
 	set_freezable();
 
-	pgdat->kswapd_order = 0;
-	pgdat->kswapd_classzone_idx = MAX_NR_ZONES;
+	WRITE_ONCE(pgdat->kswapd_order, 0);
+	WRITE_ONCE(pgdat->kswapd_classzone_idx, MAX_NR_ZONES);
 	for ( ; ; ) {
 		bool ret;
 
-		alloc_order = reclaim_order = pgdat->kswapd_order;
+		alloc_order = reclaim_order = READ_ONCE(pgdat->kswapd_order);
 		classzone_idx = kswapd_classzone_idx(pgdat, classzone_idx);
 
 kswapd_try_sleep:
@@ -3760,10 +3764,10 @@ kswapd_try_sleep:
 					classzone_idx);
 
 		/* Read the new order and classzone_idx */
-		alloc_order = reclaim_order = pgdat->kswapd_order;
+		alloc_order = reclaim_order = READ_ONCE(pgdat->kswapd_order);
 		classzone_idx = kswapd_classzone_idx(pgdat, classzone_idx);
-		pgdat->kswapd_order = 0;
-		pgdat->kswapd_classzone_idx = MAX_NR_ZONES;
+		WRITE_ONCE(pgdat->kswapd_order, 0);
+		WRITE_ONCE(pgdat->kswapd_classzone_idx, MAX_NR_ZONES);
 
 		ret = try_to_freeze();
 		if (kthread_should_stop())
@@ -3808,20 +3812,23 @@ void wakeup_kswapd(struct zone *zone, gfp_t gfp_flags, int order,
 		   enum zone_type classzone_idx)
 {
 	pg_data_t *pgdat;
+	enum zone_type curr_idx;
 
 	if (!managed_zone(zone))
 		return;
 
 	if (!cpuset_zone_allowed(zone, gfp_flags))
 		return;
+
 	pgdat = zone->zone_pgdat;
+	curr_idx = READ_ONCE(pgdat->kswapd_classzone_idx);
+
+	if (curr_idx == MAX_NR_ZONES || curr_idx < classzone_idx)
+		WRITE_ONCE(pgdat->kswapd_classzone_idx, classzone_idx);
+
+	if (READ_ONCE(pgdat->kswapd_order) < order)
+		WRITE_ONCE(pgdat->kswapd_order, order);
 
-	if (pgdat->kswapd_classzone_idx == MAX_NR_ZONES)
-		pgdat->kswapd_classzone_idx = classzone_idx;
-	else
-		pgdat->kswapd_classzone_idx = max(pgdat->kswapd_classzone_idx,
-						  classzone_idx);
-	pgdat->kswapd_order = max(pgdat->kswapd_order, order);
 	if (!waitqueue_active(&pgdat->kswapd_wait))
 		return;
 
Signature · 1 line
2.25.1
author maintainer
#143 lore raw

PATCH 141/206 mm/mmap.c: initialize align_offset explicitly for vm_unmapped_area

In reply to Sasha Levin

From: Jaewon Kim <[email protected]>

[ Upstream commit 09ef5283fd96ac424ef0e569626f359bf9ab86c9 ]

On passing requirement to vm_unmapped_area, arch_get_unmapped_area and arch_get_unmapped_area_topdown did not set align_offset. Internally on both unmapped_area and unmapped_area_topdown, if info->align_mask is 0, then info->align_offset was meaningless.

But commit df529cabb7a2 ("mm: mmap: add trace point of vm_unmapped_area") always prints info->align_offset even though it is uninitialized.

Fix this uninitialized value issue by setting it to 0 explicitly.

Before:
vm_unmapped_area: addr=0x755b155000 err=0 total_vm=0x15aaf0 flags=0x1 len=0x109000 lo=0x8000 hi=0x75eed48000 mask=0x0 ofs=0x4022

After:
vm_unmapped_area: addr=0x74a4ca1000 err=0 total_vm=0x168ab1 flags=0x1 len=0x9000 lo=0x8000 hi=0x753d94b000 mask=0x0 ofs=0x0

---
 mm/mmap.c | 2 ++
 1 file changed, 2 insertions(+)
mm/mmap.c +2 -0
index e84fd3347a518..f875386e7acd4 100644
@@ -2077,6 +2077,7 @@ arch_get_unmapped_area(struct file *filp, unsigned long addr,
 	info.low_limit = mm->mmap_base;
 	info.high_limit = TASK_SIZE;
 	info.align_mask = 0;
+	info.align_offset = 0;
 	return vm_unmapped_area(&info);
 }
 #endif
@@ -2118,6 +2119,7 @@ arch_get_unmapped_area_topdown(struct file *filp, const unsigned long addr0,
 	info.low_limit = max(PAGE_SIZE, mmap_min_addr);
 	info.high_limit = mm->mmap_base;
 	info.align_mask = 0;
+	info.align_offset = 0;
 	addr = vm_unmapped_area(&info);
 
 	/*
Signature · 1 line
2.25.1
author maintainer
#136 lore raw

PATCH 134/206 ALSA: usb-audio: Fix case when USB MIDI interface has more than one extra endpoint descriptor

In reply to Sasha Levin

From: Andreas Steinmetz <[email protected]>

[ Upstream commit 5c6cd7021a05a02fcf37f360592d7c18d4d807fb ]

The Miditech MIDIFACE 16x16 (USB ID 1290:1749) has more than one extra endpoint descriptor.

The first extra descriptor is: 0x06 0x30 0x00 0x00 0x00 0x00

As the code in snd_usbmidi_get_ms_info() looks only at the first extra descriptor to find USB_DT_CS_ENDPOINT the device as such is recognized but there is neither input nor output configured.

The patch iterates through the extra descriptors to find the proper one. With this patch the device is correctly configured.

---
 sound/usb/midi.c | 29 ++++++++++++++++++++++++-----
 1 file changed, 24 insertions(+), 5 deletions(-)
sound/usb/midi.c +24 -5
index 28a3ad8b1d74b..137e1e8718d6f 100644
@@ -1828,6 +1828,28 @@ static int snd_usbmidi_create_endpoints(struct snd_usb_midi *umidi,
 	return 0;
 }
 
+static struct usb_ms_endpoint_descriptor *find_usb_ms_endpoint_descriptor(
+					struct usb_host_endpoint *hostep)
+{
+	unsigned char *extra = hostep->extra;
+	int extralen = hostep->extralen;
+
+	while (extralen > 3) {
+		struct usb_ms_endpoint_descriptor *ms_ep =
+				(struct usb_ms_endpoint_descriptor *)extra;
+
+		if (ms_ep->bLength > 3 &&
+		    ms_ep->bDescriptorType == USB_DT_CS_ENDPOINT &&
+		    ms_ep->bDescriptorSubtype == UAC_MS_GENERAL)
+			return ms_ep;
+		if (!extra[0])
+			break;
+		extralen -= extra[0];
+		extra += extra[0];
+	}
+	return NULL;
+}
+
 /*
  * Returns MIDIStreaming device capabilities.
  */
@@ -1865,11 +1887,8 @@ static int snd_usbmidi_get_ms_info(struct snd_usb_midi *umidi,
 		ep = get_ep_desc(hostep);
 		if (!usb_endpoint_xfer_bulk(ep) && !usb_endpoint_xfer_int(ep))
 			continue;
-		ms_ep = (struct usb_ms_endpoint_descriptor *)hostep->extra;
-		if (hostep->extralen < 4 ||
-		    ms_ep->bLength < 4 ||
-		    ms_ep->bDescriptorType != USB_DT_CS_ENDPOINT ||
-		    ms_ep->bDescriptorSubtype != UAC_MS_GENERAL)
+		ms_ep = find_usb_ms_endpoint_descriptor(hostep);
+		if (!ms_ep)
 			continue;
 		if (usb_endpoint_dir_out(ep)) {
 			if (endpoints[epidx].out_ep) {
Signature · 1 line
2.25.1
author maintainer
#145 lore raw

PATCH 143/206 serial: uartps: Wait for tx_empty in console setup

In reply to Sasha Levin

From: Raviteja Narayanam <[email protected]>

[ Upstream commit 42e11948ddf68b9f799cad8c0ddeab0a39da33e8 ]

On some platforms, the log is corrupted while console is being registered. It is observed that when set_termios is called, there are still some bytes in the FIFO to be transmitted.

So, wait for tx_empty inside cdns_uart_console_setup before calling set_termios.

---
 drivers/tty/serial/xilinx_uartps.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/tty/serial/xilinx_uartps.c +8 -0
index 31950a38f0fb7..23f9b0cdff086 100644
@@ -1236,6 +1236,7 @@ static int cdns_uart_console_setup(struct console *co, char *options)
 	int bits = 8;
 	int parity = 'n';
 	int flow = 'n';
+	unsigned long time_out;
 
 	if (!port->membase) {
 		pr_debug("console on " CDNS_UART_TTY_NAME "%i not present\n",
@@ -1246,6 +1247,13 @@ static int cdns_uart_console_setup(struct console *co, char *options)
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
 
+	/* Wait for tx_empty before setting up the console */
+	time_out = jiffies + usecs_to_jiffies(TX_TIMEOUT);
+
+	while (time_before(jiffies, time_out) &&
+	       cdns_uart_tx_empty(port) != TIOCSER_TEMT)
+		cpu_relax();
+
 	return uart_set_options(port, co, baud, parity, bits, flow);
 }
 
Signature · 1 line
2.25.1
author maintainer
#71 lore raw

PATCH 70/206 ALSA: hda: Clear RIRB status before reading WP

In reply to Sasha Levin

From: Mohan Kumar <[email protected]>

[ Upstream commit 6d011d5057ff88ee556c000ac6fe0be23bdfcd72 ]

RIRB interrupt status getting cleared after the write pointer is read causes a race condition, where last response(s) into RIRB may remain unserviced by IRQ, eventually causing azx_rirb_get_response to fall back to polling mode. Clearing the RIRB interrupt status ahead of write pointer access ensures that this condition is avoided.

---
 sound/pci/hda/hda_controller.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
sound/pci/hda/hda_controller.c +9 -2
index fa261b27d8588..8198d2e53b7df 100644
@@ -1169,16 +1169,23 @@ irqreturn_t azx_interrupt(int irq, void *dev_id)
 		if (snd_hdac_bus_handle_stream_irq(bus, status, stream_update))
 			active = true;
 
-		/* clear rirb int */
 		status = azx_readb(chip, RIRBSTS);
 		if (status & RIRB_INT_MASK) {
+			/*
+			 * Clearing the interrupt status here ensures that no
+			 * interrupt gets masked after the RIRB wp is read in
+			 * snd_hdac_bus_update_rirb. This avoids a possible
+			 * race condition where codec response in RIRB may
+			 * remain unserviced by IRQ, eventually falling back
+			 * to polling mode in azx_rirb_get_response.
+			 */
+			azx_writeb(chip, RIRBSTS, RIRB_INT_MASK);
 			active = true;
 			if (status & RIRB_INT_RESPONSE) {
 				if (chip->driver_caps & AZX_DCAPS_CTX_WORKAROUND)
 					udelay(80);
 				snd_hdac_bus_update_rirb(bus);
 			}
-			azx_writeb(chip, RIRBSTS, RIRB_INT_MASK);
 		}
 	} while (active && ++repeat < 10);
 
Signature · 1 line
2.25.1
author maintainer
#150 lore raw

PATCH 148/206 KVM: arm64: vgic-its: Fix memory leak on the error path of vgic_add_lpi()

In reply to Sasha Levin

From: Zenghui Yu <[email protected]>

[ Upstream commit 57bdb436ce869a45881d8aa4bc5dac8e072dd2b6 ]

If we're going to fail out the vgic_add_lpi(), let's make sure the allocated vgic_irq memory is also freed. Though it seems that both cases are unlikely to fail.

---
 virt/kvm/arm/vgic/vgic-its.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
virt/kvm/arm/vgic/vgic-its.c +9 -2
index 9295addea7ecf..f139b1c62ca38 100644
@@ -107,14 +107,21 @@ out_unlock:
 	 * We "cache" the configuration table entries in our struct vgic_irq's.
 	 * However we only have those structs for mapped IRQs, so we read in
 	 * the respective config data from memory here upon mapping the LPI.
+	 *
+	 * Should any of these fail, behave as if we couldn't create the LPI
+	 * by dropping the refcount and returning the error.
 	 */
 	ret = update_lpi_config(kvm, irq, NULL, false);
-	if (ret)
+	if (ret) {
+		vgic_put_irq(kvm, irq);
 		return ERR_PTR(ret);
+	}
 
 	ret = vgic_v3_lpi_sync_pending_status(kvm, irq);
-	if (ret)
+	if (ret) {
+		vgic_put_irq(kvm, irq);
 		return ERR_PTR(ret);
+	}
 
 	return irq;
 }
Signature · 6 lines
2.25.1

_______________________________________________
kvmarm mailing list
[email protected]
https://lists.cs.columbia.edu/mailman/listinfo/kvmarm
author maintainer
#147 lore raw

PATCH 145/206 perf stat: Force error in fallback on :k events

In reply to Sasha Levin

From: Stephane Eranian <[email protected]>

[ Upstream commit bec49a9e05db3dbdca696fa07c62c52638fb6371 ]

When it is not possible for a non-privilege perf command to monitor at the kernel level (:k), the fallback code forces a :u. That works if the event was previously monitoring both levels. But if the event was already constrained to kernel only, then it does not make sense to restrict it to user only.

Given the code works by exclusion, a kernel only event would have:

attr->exclude_user = 1

The fallback code would add:

attr->exclude_kernel = 1

In the end the end would not monitor in either the user level or kernel level. In other words, it would count nothing.

An event programmed to monitor kernel only cannot be switched to user only without seriously warning the user.

This patch forces an error in this case to make it clear the request cannot really be satisfied.

Behavior with paranoid 1:

  $ sudo bash -c "echo 1 > /proc/sys/kernel/perf_event_paranoid"
  $ perf stat -e cycles:k sleep 1

Performance counter stats for 'sleep 1':

           1,520,413      cycles:k

         1.002361664 seconds time elapsed

         0.002480000 seconds user
         0.000000000 seconds sys

Old behavior with paranoid 2:

  $ sudo bash -c "echo 2 > /proc/sys/kernel/perf_event_paranoid"
  $ perf stat -e cycles:k sleep 1
   Performance counter stats for 'sleep 1':
                   0      cycles:ku

         1.002358127 seconds time elapsed

         0.002384000 seconds user
         0.000000000 seconds sys

New behavior with paranoid 2:

  $ sudo bash -c "echo 2 > /proc/sys/kernel/perf_event_paranoid"
  $ perf stat -e cycles:k sleep 1
  Error:
  You may not have permission to collect stats.

Consider tweaking /proc/sys/kernel/perf_event_paranoid, which controls use of the performance events system by unprivileged users (without CAP_PERFMON or CAP_SYS_ADMIN).

The current value is 2:

-1: Allow use of (almost) all events by all users
Ignore mlock limit after perf_event_mlock_kb without CAP_IPC_LOCK

Quoted 1 line

= 0: Disallow ftrace function tracepoint by users without CAP_PERFMON or CAP_SYS_ADMIN

Disallow raw tracepoint access by users without CAP_SYS_PERFMON or CAP_SYS_ADMIN

Quoted 2 lines

= 1: Disallow CPU event access by users without CAP_PERFMON or CAP_SYS_ADMIN = 2: Disallow kernel profiling by users without CAP_PERFMON or CAP_SYS_ADMIN

To make this setting permanent, edit /etc/sysctl.conf too, e.g.:

kernel.perf_event_paranoid = -1

v2 of this patch addresses the review feedback from [email protected].

---
 tools/perf/util/evsel.c | 4 ++++
 1 file changed, 4 insertions(+)
tools/perf/util/evsel.c +4 -0
index 68c5ab0e1800b..e8586957562b3 100644
@@ -2796,6 +2796,10 @@ bool perf_evsel__fallback(struct perf_evsel *evsel, int err,
 		char *new_name;
 		const char *sep = ":";
 
+		/* If event has exclude user then don't exclude kernel. */
+		if (evsel->core.attr.exclude_user)
+			return false;
+
 		/* Is there already the separator in the name. */
 		if (strchr(name, '/') ||
 		    strchr(name, ':'))
Signature · 1 line
2.25.1
author maintainer
#156 lore raw

PATCH 154/206 dt-bindings: sound: wm8994: Correct required supplies based on actual implementaion

In reply to Sasha Levin

From: Krzysztof Kozlowski <[email protected]>

[ Upstream commit 8c149b7d75e53be47648742f40fc90d9fc6fa63a ]

The required supplies in bindings were actually not matching implementation making the bindings incorrect and misleading. The Linux kernel driver requires all supplies to be present. Also for wlf,wm8994 uses just DBVDD-supply instead of DBVDDn-supply (n: <1,3>).

---
 .../devicetree/bindings/sound/wm8994.txt       | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)
Documentation/devicetree/bindings/sound/wm8994.txt +12 -6
index 68cccc4653ba3..367b58ce1bb92 100644
@@ -14,9 +14,15 @@ Required properties:
   - #gpio-cells : Must be 2. The first cell is the pin number and the
     second cell is used to specify optional parameters (currently unused).
 
-  - AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply,
-    SPKVDD1-supply, SPKVDD2-supply : power supplies for the device, as covered
-    in Documentation/devicetree/bindings/regulator/regulator.txt
+  - power supplies for the device, as covered in
+    Documentation/devicetree/bindings/regulator/regulator.txt, depending
+    on compatible:
+    - for wlf,wm1811 and wlf,wm8958:
+      AVDD1-supply, AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply,
+      DCVDD-supply, CPVDD-supply, SPKVDD1-supply, SPKVDD2-supply
+    - for wlf,wm8994:
+      AVDD1-supply, AVDD2-supply, DBVDD-supply, DCVDD-supply, CPVDD-supply,
+      SPKVDD1-supply, SPKVDD2-supply
 
 Optional properties:
 
@@ -73,11 +79,11 @@ wm8994: codec@1a {
 
 	lineout1-se;
 
+	AVDD1-supply = <&regulator>;
 	AVDD2-supply = <&regulator>;
 	CPVDD-supply = <&regulator>;
-	DBVDD1-supply = <&regulator>;
-	DBVDD2-supply = <&regulator>;
-	DBVDD3-supply = <&regulator>;
+	DBVDD-supply = <&regulator>;
+	DCVDD-supply = <&regulator>;
 	SPKVDD1-supply = <&regulator>;
 	SPKVDD2-supply = <&regulator>;
 };
Signature · 1 line
2.25.1
author maintainer
#157 lore raw

PATCH 155/206 atm: fix a memory leak of vcc->user_back

In reply to Sasha Levin

From: Cong Wang <[email protected]>

[ Upstream commit 8d9f73c0ad2f20e9fed5380de0a3097825859d03 ]

In lec_arp_clear_vccs() only entry->vcc is freed, but vcc could be installed on entry->recv_vcc too in lec_vcc_added().

This fixes the following memory leak:

unreferenced object 0xffff8880d9266b90 (size 16):
comm "atm2", pid 425, jiffies 4294907980 (age 23.488s) hex dump (first 16 bytes):

    00 00 00 00 00 00 00 00 00 00 00 00 6b 6b 6b a5  ............kkk.
  backtrace:
    [<(____ptrval____)>] kmem_cache_alloc_trace+0x10e/0x151
    [<(____ptrval____)>] lane_ioctl+0x4b3/0x569
    [<(____ptrval____)>] do_vcc_ioctl+0x1ea/0x236
    [<(____ptrval____)>] svc_ioctl+0x17d/0x198
    [<(____ptrval____)>] sock_do_ioctl+0x47/0x12f
    [<(____ptrval____)>] sock_ioctl+0x2f9/0x322
    [<(____ptrval____)>] vfs_ioctl+0x1e/0x2b
    [<(____ptrval____)>] ksys_ioctl+0x61/0x80
    [<(____ptrval____)>] __x64_sys_ioctl+0x16/0x19
    [<(____ptrval____)>] do_syscall_64+0x57/0x65
    [<(____ptrval____)>] entry_SYSCALL_64_after_hwframe+0x49/0xb3
---
 net/atm/lec.c | 6 ++++++
 1 file changed, 6 insertions(+)
net/atm/lec.c +6 -0
index ad4f829193f05..5a6186b809874 100644
@@ -1270,6 +1270,12 @@ static void lec_arp_clear_vccs(struct lec_arp_table *entry)
 		entry->vcc = NULL;
 	}
 	if (entry->recv_vcc) {
+		struct atm_vcc *vcc = entry->recv_vcc;
+		struct lec_vcc_priv *vpriv = LEC_VCC_PRIV(vcc);
+
+		kfree(vpriv);
+		vcc->user_back = NULL;
+
 		entry->recv_vcc->push = entry->old_recv_push;
 		vcc_release_async(entry->recv_vcc, -EPIPE);
 		entry->recv_vcc = NULL;
Signature · 1 line
2.25.1
author maintainer
#161 lore raw

PATCH 159/206 phy: samsung: s5pv210-usb2: Add delay after reset

In reply to Sasha Levin

From: Jonathan Bakker <[email protected]>

[ Upstream commit 05942b8c36c7eb5d3fc5e375d4b0d0c49562e85d ]

The USB phy takes some time to reset, so make sure we give it to it. The delay length was taken from the 4x12 phy driver.

This manifested in issues with the DWC2 driver since commit fe369e1826b3 ("usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.") where the endianness check would read the DWC ID as 0 due to the phy still resetting, resulting in the wrong endian mode being chosen.

---
 drivers/phy/samsung/phy-s5pv210-usb2.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/phy/samsung/phy-s5pv210-usb2.c +4 -0
index f6f72339bbc32..bb7fdf491c1c2 100644
@@ -142,6 +142,10 @@ static void s5pv210_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on)
 		udelay(10);
 		rst &= ~rstbits;
 		writel(rst, drv->reg_phy + S5PV210_UPHYRST);
+		/* The following delay is necessary for the reset sequence to be
+		 * completed
+		 */
+		udelay(80);
 	} else {
 		pwr = readl(drv->reg_phy + S5PV210_UPHYPWR);
 		pwr |= phypwr;
Signature · 1 line
2.25.1
author maintainer
#164 lore raw

PATCH 162/206 tipc: fix memory leak in service subscripting

In reply to Sasha Levin

From: Tuong Lien <[email protected]>

[ Upstream commit 0771d7df819284d46cf5cfb57698621b503ec17f ]

Upon receipt of a service subscription request from user via a topology connection, one 'sub' object will be allocated in kernel, so it will be able to send an event of the service if any to the user correspondingly then. Also, in case of any failure, the connection will be shutdown and all the pertaining 'sub' objects will be freed.

However, there is a race condition as follows resulting in memory leak:

       receive-work       connection        send-work
              |                |                |
        sub-1 |<------//-------|                |
        sub-2 |<------//-------|                |
              |                |<---------------| evt for sub-x
        sub-3 |<------//-------|                |
              :                :                :
              :                :                :
              |       /--------|                |
              |       |        * peer closed    |
              |       |        |                |
              |       |        |<-------X-------| evt for sub-y
              |       |        |<===============|
        sub-n |<------/        X    shutdown    |
    -> orphan |                                 |

That is, the 'receive-work' may get the last subscription request while the 'send-work' is shutting down the connection due to peer close.

We had a 'lock' on the connection, so the two actions cannot be carried out simultaneously. If the last subscription is allocated e.g. 'sub-n', before the 'send-work' closes the connection, there will be no issue at all, the 'sub' objects will be freed. In contrast the last subscription will become orphan since the connection was closed, and we released all references.

This commit fixes the issue by simply adding one test if the connection remains in 'connected' state right after we obtain the connection lock, then a subscription object can be created as usual, otherwise we ignore it.

---
 net/tipc/topsrv.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
net/tipc/topsrv.c +3 -1
index 41f4464ac6cc5..ec9a7137d2677 100644
@@ -407,7 +407,9 @@ static int tipc_conn_rcv_from_sock(struct tipc_conn *con)
 		return -EWOULDBLOCK;
 	if (ret == sizeof(s)) {
 		read_lock_bh(&sk->sk_callback_lock);
-		ret = tipc_conn_rcv_sub(srv, con, &s);
+		/* RACE: the connection can be closed in the meantime */
+		if (likely(connected(con)))
+			ret = tipc_conn_rcv_sub(srv, con, &s);
 		read_unlock_bh(&sk->sk_callback_lock);
 		if (!ret)
 			return 0;
Signature · 1 line
2.25.1
author maintainer
#169 lore raw

PATCH 167/206 USB: EHCI: ehci-mv: fix less than zero comparison of an unsigned int

In reply to Sasha Levin

From: Colin Ian King <[email protected]>

[ Upstream commit a7f40c233a6b0540d28743267560df9cfb571ca9 ]

The comparison of hcd->irq to less than zero for an error check will never be true because hcd->irq is an unsigned int. Fix this by assigning the int retval to the return of platform_get_irq and checking this for the -ve error condition and assigning hcd->irq to retval.

Addresses-Coverity: ("Unsigned compared against 0")

Fixes c856b4b0fdb5 ("USB: EHCI: ehci-mv: fix error handling in mv_ehci_probe()")
---
 drivers/usb/host/ehci-mv.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/usb/host/ehci-mv.c +3 -4
index 4edcd7536a01b..9d93e7441bbca 100644
@@ -192,11 +192,10 @@ static int mv_ehci_probe(struct platform_device *pdev)
 	hcd->rsrc_len = resource_size(r);
 	hcd->regs = ehci_mv->op_regs;
 
-	hcd->irq = platform_get_irq(pdev, 0);
-	if (hcd->irq < 0) {
-		retval = hcd->irq;
+	retval = platform_get_irq(pdev, 0);
+	if (retval < 0)
 		goto err_disable_clk;
-	}
+	hcd->irq = retval;
 
 	ehci = hcd_to_ehci(hcd);
 	ehci->caps = (struct ehci_caps *) ehci_mv->cap_regs;
Signature · 1 line
2.25.1
author maintainer
#173 lore raw

PATCH 171/206 drm/nouveau/debugfs: fix runtime pm imbalance on error

In reply to Sasha Levin

From: Dinghao Liu <[email protected]>

[ Upstream commit 00583fbe8031f69bba8b0a9a861efb75fb7131af ]

pm_runtime_get_sync() increments the runtime PM usage counter even the call returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced.

---
 drivers/gpu/drm/nouveau/nouveau_debugfs.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/gpu/drm/nouveau/nouveau_debugfs.c +4 -1
index 9635704a1d864..4561a786fab07 100644
@@ -161,8 +161,11 @@ nouveau_debugfs_pstate_set(struct file *file, const char __user *ubuf,
 	}
 
 	ret = pm_runtime_get_sync(drm->dev);
-	if (ret < 0 && ret != -EACCES)
+	if (ret < 0 && ret != -EACCES) {
+		pm_runtime_put_autosuspend(drm->dev);
 		return ret;
+	}
+
 	ret = nvif_mthd(ctrl, NVIF_CONTROL_PSTATE_USER, &args, sizeof(args));
 	pm_runtime_put_autosuspend(drm->dev);
 	if (ret < 0)
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#170 lore raw

PATCH 168/206 scsi: cxlflash: Fix error return code in cxlflash_probe()

In reply to Sasha Levin

From: Wei Yongjun <[email protected]>

[ Upstream commit d0b1e4a638d670a09f42017a3e567dc846931ba8 ]

Fix to return negative error code -ENOMEM from create_afu error handling case instead of 0, as done elsewhere in this function.

---
 drivers/scsi/cxlflash/main.c | 1 +
 1 file changed, 1 insertion(+)
drivers/scsi/cxlflash/main.c +1 -0
index f987c40c47a13..443813feaef47 100644
@@ -3749,6 +3749,7 @@ static int cxlflash_probe(struct pci_dev *pdev,
 	cfg->afu_cookie = cfg->ops->create_afu(pdev);
 	if (unlikely(!cfg->afu_cookie)) {
 		dev_err(dev, "%s: create_afu failed\n", __func__);
+		rc = -ENOMEM;
 		goto out_remove;
 	}
 
Signature · 1 line
2.25.1
author maintainer
#174 lore raw

PATCH 172/206 drm/nouveau: fix runtime pm imbalance on error

In reply to Sasha Levin

From: Dinghao Liu <[email protected]>

[ Upstream commit d7372dfb3f7f1602b87e0663e8b8646da23ebca7 ]

pm_runtime_get_sync() increments the runtime PM usage counter even the call returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced.

---
 drivers/gpu/drm/nouveau/nouveau_gem.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/gpu/drm/nouveau/nouveau_gem.c +3 -1
index 791f970714ed6..a98fccb0d32f9 100644
@@ -82,8 +82,10 @@ nouveau_gem_object_open(struct drm_gem_object *gem, struct drm_file *file_priv)
 		return ret;
 
 	ret = pm_runtime_get_sync(dev);
-	if (ret < 0 && ret != -EACCES)
+	if (ret < 0 && ret != -EACCES) {
+		pm_runtime_put_autosuspend(dev);
 		goto out;
+	}
 
 	ret = nouveau_vma_new(nvbo, &cli->vmm, &vma);
 	pm_runtime_mark_last_busy(dev);
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#175 lore raw

PATCH 173/206 drm/nouveau/dispnv50: fix runtime pm imbalance on error

In reply to Sasha Levin

From: Dinghao Liu <[email protected]>

[ Upstream commit dc455f4c888365595c0a13da445e092422d55b8d ]

pm_runtime_get_sync() increments the runtime PM usage counter even the call returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced.

---
 drivers/gpu/drm/nouveau/dispnv50/disp.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/gpu/drm/nouveau/dispnv50/disp.c +3 -1
index e06ea8c8184cb..1bb0a9f6fa730 100644
@@ -909,8 +909,10 @@ nv50_mstc_detect(struct drm_connector *connector, bool force)
 		return connector_status_disconnected;
 
 	ret = pm_runtime_get_sync(connector->dev->dev);
-	if (ret < 0 && ret != -EACCES)
+	if (ret < 0 && ret != -EACCES) {
+		pm_runtime_put_autosuspend(connector->dev->dev);
 		return connector_status_disconnected;
+	}
 
 	conn_status = drm_dp_mst_detect_port(connector, mstc->port->mgr,
 					     mstc->port);
Signature · 6 lines
2.25.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#162 lore raw

PATCH 160/206 Bluetooth: Handle Inquiry Cancel error after Inquiry Complete

In reply to Sasha Levin

From: Sonny Sasaka <[email protected]>

[ Upstream commit adf1d6926444029396861413aba8a0f2a805742a ]

After sending Inquiry Cancel command to the controller, it is possible that Inquiry Complete event comes before Inquiry Cancel command complete event. In this case the Inquiry Cancel command will have status of Command Disallowed since there is no Inquiry session to be cancelled. This case should not be treated as error, otherwise we can reach an inconsistent state.

Example of a btmon trace when this happened:

< HCI Command: Inquiry Cancel (0x01|0x0002) plen 0

Quoted 1 line

HCI Event: Inquiry Complete (0x01) plen 1

        Status: Success (0x00)
Quoted 1 line

HCI Event: Command Complete (0x0e) plen 4

      Inquiry Cancel (0x01|0x0002) ncmd 1
        Status: Command Disallowed (0x0c)
---
 net/bluetooth/hci_event.c | 19 +++++++++++++++++--
 1 file changed, 17 insertions(+), 2 deletions(-)
net/bluetooth/hci_event.c +17 -2
index ec6b3a87b3e7f..310622086f74b 100644
@@ -41,12 +41,27 @@
 
 /* Handle HCI Event packets */
 
-static void hci_cc_inquiry_cancel(struct hci_dev *hdev, struct sk_buff *skb)
+static void hci_cc_inquiry_cancel(struct hci_dev *hdev, struct sk_buff *skb,
+				  u8 *new_status)
 {
 	__u8 status = *((__u8 *) skb->data);
 
 	BT_DBG("%s status 0x%2.2x", hdev->name, status);
 
+	/* It is possible that we receive Inquiry Complete event right
+	 * before we receive Inquiry Cancel Command Complete event, in
+	 * which case the latter event should have status of Command
+	 * Disallowed (0x0c). This should not be treated as error, since
+	 * we actually achieve what Inquiry Cancel wants to achieve,
+	 * which is to end the last Inquiry session.
+	 */
+	if (status == 0x0c && !test_bit(HCI_INQUIRY, &hdev->flags)) {
+		bt_dev_warn(hdev, "Ignoring error of Inquiry Cancel command");
+		status = 0x00;
+	}
+
+	*new_status = status;
+
 	if (status)
 		return;
 
@@ -3039,7 +3054,7 @@ static void hci_cmd_complete_evt(struct hci_dev *hdev, struct sk_buff *skb,
 
 	switch (*opcode) {
 	case HCI_OP_INQUIRY_CANCEL:
-		hci_cc_inquiry_cancel(hdev, skb);
+		hci_cc_inquiry_cancel(hdev, skb, status);
 		break;
 
 	case HCI_OP_PERIODIC_INQ:
Signature · 1 line
2.25.1
author maintainer
#167 lore raw

PATCH 165/206 powerpc/traps: Make unrecoverable NMIs die instead of panic

In reply to Sasha Levin

From: Nicholas Piggin <[email protected]>

[ Upstream commit 265d6e588d87194c2fe2d6c240247f0264e0c19b ]

System Reset and Machine Check interrupts that are not recoverable due to being nested or interrupting when RI=0 currently panic. This is not necessary, and can often just kill the current context and recover.

---
 arch/powerpc/kernel/traps.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
arch/powerpc/kernel/traps.c +3 -3
index d5f351f02c153..7781f0168ce8c 100644
@@ -430,11 +430,11 @@ out:
 #ifdef CONFIG_PPC_BOOK3S_64
 	BUG_ON(get_paca()->in_nmi == 0);
 	if (get_paca()->in_nmi > 1)
-		nmi_panic(regs, "Unrecoverable nested System Reset");
+		die("Unrecoverable nested System Reset", regs, SIGABRT);
 #endif
 	/* Must die if the interrupt is not recoverable */
 	if (!(regs->msr & MSR_RI))
-		nmi_panic(regs, "Unrecoverable System Reset");
+		die("Unrecoverable System Reset", regs, SIGABRT);
 
 	if (!nested)
 		nmi_exit();
@@ -775,7 +775,7 @@ void machine_check_exception(struct pt_regs *regs)
 
 	/* Must die if the interrupt is not recoverable */
 	if (!(regs->msr & MSR_RI))
-		nmi_panic(regs, "Unrecoverable Machine check");
+		die("Unrecoverable Machine check", regs, SIGBUS);
 
 	return;
 
Signature · 1 line
2.25.1
author maintainer
#168 lore raw

PATCH 166/206 fuse: don't check refcount after stealing page

In reply to Sasha Levin

From: Miklos Szeredi <[email protected]>

[ Upstream commit 32f98877c57bee6bc27f443a96f49678a2cd6a50 ]

page_count() is unstable. Unless there has been an RCU grace period between when the page was removed from the page cache and now, a speculative reference may exist from the page cache.

---
 fs/fuse/dev.c | 1 -
 1 file changed, 1 deletion(-)
fs/fuse/dev.c +0 -1
index 01e6ea11822bf..c51c9a6881e49 100644
@@ -831,7 +831,6 @@ static int fuse_check_page(struct page *page)
 {
 	if (page_mapcount(page) ||
 	    page->mapping != NULL ||
-	    page_count(page) != 1 ||
 	    (page->flags & PAGE_FLAGS_CHECK_AT_PREP &
 	     ~(1 << PG_locked |
 	       1 << PG_referenced |
Signature · 1 line
2.25.1
author maintainer
#81 lore raw

PATCH 80/206 ALSA: usb-audio: Don't create a mixer element with bogus volume range

In reply to Sasha Levin

From: Takashi Iwai <[email protected]>

[ Upstream commit e9a0ef0b5ddcbc0d56c65aefc0f18d16e6f71207 ]

Some USB-audio descriptors provide a bogus volume range (e.g. volume min and max are identical), which confuses user-space. This patch makes the driver skipping such a control element.

---
 sound/usb/mixer.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
sound/usb/mixer.c +10 -0
index 45bd3d54be54b..451b8ea383c61 100644
@@ -1699,6 +1699,16 @@ static void __build_feature_ctl(struct usb_mixer_interface *mixer,
 	/* get min/max values */
 	get_min_max_with_quirks(cval, 0, kctl);
 
+	/* skip a bogus volume range */
+	if (cval->max <= cval->min) {
+		usb_audio_dbg(mixer->chip,
+			      "[%d] FU [%s] skipped due to invalid volume\n",
+			      cval->head.id, kctl->id.name);
+		snd_ctl_free_one(kctl);
+		return;
+	}
+
+
 	if (control == UAC_FU_VOLUME) {
 		check_mapped_dB(map, cval);
 		if (cval->dBmin < cval->dBmax || !cval->initialized) {
Signature · 1 line
2.25.1
author maintainer
#178 lore raw

PATCH 176/206 btrfs: don't force read-only after error in drop snapshot

In reply to Sasha Levin

From: David Sterba <[email protected]>

[ Upstream commit 7c09c03091ac562ddca2b393e5d65c1d37da79f1 ]

Deleting a subvolume on a full filesystem leads to ENOSPC followed by a forced read-only. This is not a transaction abort and the filesystem is otherwise ok, so the error should be just propagated to the callers.

This is caused by unnecessary call to btrfs_handle_fs_error for all errors, except EAGAIN. This does not make sense as the standard transaction abort mechanism is in btrfs_drop_snapshot so all relevant failures are handled.

Originally in commit cb1b69f4508a ("Btrfs: forced readonly when btrfs_drop_snapshot() fails") there was no return value at all, so the btrfs_std_error made some sense but once the error handling and propagation has been implemented we don't need it anymore.

---
 fs/btrfs/extent-tree.c | 2 --
 1 file changed, 2 deletions(-)
fs/btrfs/extent-tree.c +0 -2
index ec3aa76d19b7f..be0776eba7a08 100644
@@ -9099,8 +9099,6 @@ out:
 	 */
 	if (!for_reloc && !root_dropped)
 		btrfs_add_dead_root(root);
-	if (err && err != -EAGAIN)
-		btrfs_handle_fs_error(fs_info, err, NULL);
 	return err;
 }
 
Signature · 1 line
2.25.1
author maintainer
#190 lore raw

PATCH 188/206 mtd: rawnand: omap_elm: Fix runtime PM imbalance on error

In reply to Sasha Levin

From: Dinghao Liu <[email protected]>

[ Upstream commit 37f7212148cf1d796135cdf8d0c7fee13067674b ]

pm_runtime_get_sync() increments the runtime PM usage counter even when it returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced.

---
 drivers/mtd/nand/raw/omap_elm.c | 1 +
 1 file changed, 1 insertion(+)
drivers/mtd/nand/raw/omap_elm.c +1 -0
index a3f32f939cc17..6736777a41567 100644
@@ -421,6 +421,7 @@ static int elm_probe(struct platform_device *pdev)
 	pm_runtime_enable(&pdev->dev);
 	if (pm_runtime_get_sync(&pdev->dev) < 0) {
 		ret = -EINVAL;
+		pm_runtime_put_sync(&pdev->dev);
 		pm_runtime_disable(&pdev->dev);
 		dev_err(&pdev->dev, "can't enable clock\n");
 		return ret;
Signature · 1 line
2.25.1
author maintainer
#189 lore raw

PATCH 187/206 wlcore: fix runtime pm imbalance in wlcore_regdomain_config

In reply to Sasha Levin

From: Dinghao Liu <[email protected]>

[ Upstream commit 282a04bf1d8029eb98585cb5db3fd70fe8bc91f7 ]

pm_runtime_get_sync() increments the runtime PM usage counter even the call returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced.

---
 drivers/net/wireless/ti/wlcore/main.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/net/wireless/ti/wlcore/main.c +3 -1
index 2ca5658bbc2ab..43c7b37dec0c9 100644
@@ -3671,8 +3671,10 @@ void wlcore_regdomain_config(struct wl1271 *wl)
 		goto out;
 
 	ret = pm_runtime_get_sync(wl->dev);
-	if (ret < 0)
+	if (ret < 0) {
+		pm_runtime_put_autosuspend(wl->dev);
 		goto out;
+	}
 
 	ret = wlcore_cmd_regdomain_config_locked(wl);
 	if (ret < 0) {
Signature · 1 line
2.25.1
author maintainer
#188 lore raw

PATCH 186/206 wlcore: fix runtime pm imbalance in wl1271_tx_work

In reply to Sasha Levin

From: Dinghao Liu <[email protected]>

[ Upstream commit 9604617e998b49f7695fea1479ed82421ef8c9f0 ]

There are two error handling paths in this functon. When wlcore_tx_work_locked() returns an error code, we should decrease the runtime PM usage counter the same way as the error handling path beginning from pm_runtime_get_sync().

---
 drivers/net/wireless/ti/wlcore/tx.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/wireless/ti/wlcore/tx.c +1 -0
index b6e19c2d66b0a..250bcbf4ea2f2 100644
@@ -877,6 +877,7 @@ void wl1271_tx_work(struct work_struct *work)
 
 	ret = wlcore_tx_work_locked(wl);
 	if (ret < 0) {
+		pm_runtime_put_noidle(wl->dev);
 		wl12xx_queue_recovery_work(wl);
 		goto out;
 	}
Signature · 1 line
2.25.1
author maintainer
#193 lore raw

PATCH 191/206 mm/swap_state: fix a data race in swapin_nr_pages

In reply to Sasha Levin

From: Qian Cai <[email protected]>

[ Upstream commit d6c1f098f2a7ba62627c9bc17cda28f534ef9e4a ]

"prev_offset" is a static variable in swapin_nr_pages() that can be accessed concurrently with only mmap_sem held in read mode as noticed by KCSAN,

 BUG: KCSAN: data-race in swap_cluster_readahead / swap_cluster_readahead

write to 0xffffffff92763830 of 8 bytes by task 14795 on cpu 17:

  swap_cluster_readahead+0x2a6/0x5e0
  swapin_readahead+0x92/0x8dc
  do_swap_page+0x49b/0xf20
  __handle_mm_fault+0xcfb/0xd70
  handle_mm_fault+0xfc/0x2f0
  do_page_fault+0x263/0x715
  page_fault+0x34/0x40

1 lock held by (dnf)/14795:
#0: ffff897bd2e98858 (&mm->mmap_sem#2){++++}-{3:3}, at: do_page_fault+0x143/0x715 do_user_addr_fault at arch/x86/mm/fault.c:1405
(inlined by) do_page_fault at arch/x86/mm/fault.c:1535

 irq event stamp: 83493
 count_memcg_event_mm+0x1a6/0x270
 count_memcg_event_mm+0x119/0x270
 __do_softirq+0x365/0x589
 irq_exit+0xa2/0xc0

read to 0xffffffff92763830 of 8 bytes by task 1 on cpu 22:

  swap_cluster_readahead+0xfd/0x5e0
  swapin_readahead+0x92/0x8dc
  do_swap_page+0x49b/0xf20
  __handle_mm_fault+0xcfb/0xd70
  handle_mm_fault+0xfc/0x2f0
  do_page_fault+0x263/0x715
  page_fault+0x34/0x40

1 lock held by systemd/1:
#0: ffff897c38f14858 (&mm->mmap_sem#2){++++}-{3:3}, at: do_page_fault+0x143/0x715

 irq event stamp: 43530289
 count_memcg_event_mm+0x1a6/0x270
 count_memcg_event_mm+0x119/0x270
 __do_softirq+0x365/0x589
 irq_exit+0xa2/0xc0
---
 mm/swap_state.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
mm/swap_state.c +3 -2
index 09731f4174c7e..3febffe0fca4a 100644
@@ -537,10 +537,11 @@ static unsigned long swapin_nr_pages(unsigned long offset)
 		return 1;
 
 	hits = atomic_xchg(&swapin_readahead_hits, 0);
-	pages = __swapin_nr_pages(prev_offset, offset, hits, max_pages,
+	pages = __swapin_nr_pages(READ_ONCE(prev_offset), offset, hits,
+				  max_pages,
 				  atomic_read(&last_readahead_pages));
 	if (!hits)
-		prev_offset = offset;
+		WRITE_ONCE(prev_offset, offset);
 	atomic_set(&last_readahead_pages, pages);
 
 	return pages;
Signature · 1 line
2.25.1
author maintainer
#198 lore raw

PATCH 196/206 cifs: Fix double add page to memcg when cifs_readpages

In reply to Sasha Levin

From: Zhang Xiaoxu <[email protected]>

[ Upstream commit 95a3d8f3af9b0d63b43f221b630beaab9739d13a ]

When xfstests generic/451, there is an BUG at mm/memcontrol.c:
page:ffffea000560f2c0 refcount:2 mapcount:0 mapping:000000008544e0ea

       index:0xf
  mapping->aops:cifs_addr_ops dentry name:"tst-aio-dio-cycle-write.451"
  flags: 0x2fffff80000001(locked)
  raw: 002fffff80000001 ffffc90002023c50 ffffea0005280088 ffff88815cda0210
  raw: 000000000000000f 0000000000000000 00000002ffffffff ffff88817287d000
  page dumped because: VM_BUG_ON_PAGE(page->mem_cgroup)
  page->mem_cgroup:ffff88817287d000
  ------------[ cut here ]------------
  kernel BUG at mm/memcontrol.c:2659!
  invalid opcode: 0000 [#1] SMP
  CPU: 2 PID: 2038 Comm: xfs_io Not tainted 5.8.0-rc1 #44
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20190727_
    073836-buildvm-ppc64le-16.ppc.4
  RIP: 0010:commit_charge+0x35/0x50
  Code: 0d 48 83 05 54 b2 02 05 01 48 89 77 38 c3 48 c7
        c6 78 4a ea ba 48 83 05 38 b2 02 05 01 e8 63 0d9
  RSP: 0018:ffffc90002023a50 EFLAGS: 00010202
  RAX: 0000000000000000 RBX: ffff88817287d000 RCX: 0000000000000000
  RDX: 0000000000000000 RSI: ffff88817ac97ea0 RDI: ffff88817ac97ea0
  RBP: ffffea000560f2c0 R08: 0000000000000203 R09: 0000000000000005
  R10: 0000000000000030 R11: ffffc900020237a8 R12: 0000000000000000
  R13: 0000000000000001 R14: 0000000000000001 R15: ffff88815a1272c0
  FS:  00007f5071ab0800(0000) GS:ffff88817ac80000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 000055efcd5ca000 CR3: 000000015d312000 CR4: 00000000000006e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   mem_cgroup_charge+0x166/0x4f0
   __add_to_page_cache_locked+0x4a9/0x710
   add_to_page_cache_locked+0x15/0x20
   cifs_readpages+0x217/0x1270
   read_pages+0x29a/0x670
   page_cache_readahead_unbounded+0x24f/0x390
   __do_page_cache_readahead+0x3f/0x60
   ondemand_readahead+0x1f1/0x470
   page_cache_async_readahead+0x14c/0x170
   generic_file_buffered_read+0x5df/0x1100
   generic_file_read_iter+0x10c/0x1d0
   cifs_strict_readv+0x139/0x170
   new_sync_read+0x164/0x250
   __vfs_read+0x39/0x60
   vfs_read+0xb5/0x1e0
   ksys_pread64+0x85/0xf0
   __x64_sys_pread64+0x22/0x30
   do_syscall_64+0x69/0x150
   entry_SYSCALL_64_after_hwframe+0x44/0xa9
  RIP: 0033:0x7f5071fcb1af
  Code: Bad RIP value.
  RSP: 002b:00007ffde2cdb8e0 EFLAGS: 00000293 ORIG_RAX: 0000000000000011
  RAX: ffffffffffffffda RBX: 00007ffde2cdb990 RCX: 00007f5071fcb1af
  RDX: 0000000000001000 RSI: 000055efcd5ca000 RDI: 0000000000000003
  RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000
  R10: 0000000000001000 R11: 0000000000000293 R12: 0000000000000001
  R13: 000000000009f000 R14: 0000000000000000 R15: 0000000000001000
  Modules linked in:
  ---[ end trace 725fa14a3e1af65c ]---

Since commit 3fea5a499d57 ("mm: memcontrol: convert page cache to a new mem_cgroup_charge() API") not cancel the page charge, the pages maybe double add to pagecache:
thread1 | thread2
cifs_readpages
readpages_get_pages
add_to_page_cache_locked(head,index=n)=0

                              | readpages_get_pages
                              | add_to_page_cache_locked(head,index=n+1)=0

add_to_page_cache_locked(head, index=n+1)=-EEXIST then, will next loop with list head page's index=n+1 and the page->mapping not NULL
readpages_get_pages add_to_page_cache_locked(head, index=n+1)
commit_charge
VM_BUG_ON_PAGE

So, we should not do the next loop when any page add to page cache failed.

---
 fs/cifs/file.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)
fs/cifs/file.c +7 -4
index e78b52c582f18..5cb15649adb07 100644
@@ -3804,7 +3804,8 @@ readpages_get_pages(struct address_space *mapping, struct list_head *page_list,
 			break;
 
 		__SetPageLocked(page);
-		if (add_to_page_cache_locked(page, mapping, page->index, gfp)) {
+		rc = add_to_page_cache_locked(page, mapping, page->index, gfp);
+		if (rc) {
 			__ClearPageLocked(page);
 			break;
 		}
@@ -3820,6 +3821,7 @@ static int cifs_readpages(struct file *file, struct address_space *mapping,
 	struct list_head *page_list, unsigned num_pages)
 {
 	int rc;
+	int err = 0;
 	struct list_head tmplist;
 	struct cifsFileInfo *open_file = file->private_data;
 	struct cifs_sb_info *cifs_sb = CIFS_FILE_SB(file);
@@ -3860,7 +3862,7 @@ static int cifs_readpages(struct file *file, struct address_space *mapping,
 	 * the order of declining indexes. When we put the pages in
 	 * the rdata->pages, then we want them in increasing order.
 	 */
-	while (!list_empty(page_list)) {
+	while (!list_empty(page_list) && !err) {
 		unsigned int i, nr_pages, bytes, rsize;
 		loff_t offset;
 		struct page *page, *tpage;
@@ -3883,9 +3885,10 @@ static int cifs_readpages(struct file *file, struct address_space *mapping,
 			return 0;
 		}
 
-		rc = readpages_get_pages(mapping, page_list, rsize, &tmplist,
+		nr_pages = 0;
+		err = readpages_get_pages(mapping, page_list, rsize, &tmplist,
 					 &nr_pages, &offset, &bytes);
-		if (rc) {
+		if (!nr_pages) {
 			add_credits_and_wake_if(server, credits, 0);
 			break;
 		}
Signature · 1 line
2.25.1
author maintainer
#199 lore raw

PATCH 197/206 nvme: fix possible deadlock when I/O is blocked

In reply to Sasha Levin

From: Sagi Grimberg <[email protected]>

[ Upstream commit 3b4b19721ec652ad2c4fe51dfbe5124212b5f581 ]

Revert fab7772bfbcf ("nvme-multipath: revalidate nvme_ns_head gendisk in nvme_validate_ns")

When adding a new namespace to the head disk (via nvme_mpath_set_live) we will see partition scan which triggers I/O on the mpath device node. This process will usually be triggered from the scan_work which holds the scan_lock. If I/O blocks (if we got ana change currently have only available paths but none are accessible) this can deadlock on the head disk bd_mutex as both partition scan I/O takes it, and head disk revalidation takes it to check for resize (also triggered from scan_work on a different path). See trace [1].

The mpath disk revalidation was originally added to detect online disk size change, but this is no longer needed since commit cb224c3af4df ("nvme: Convert to use set_capacity_revalidate_and_notify") which already updates resize info without unnecessarily revalidating the disk (the mpath disk doesn't even implement .revalidate_disk fop).

[1]:
--

kernel: INFO: task kworker/u65:9:494 blocked for more than 241 seconds.
kernel:       Tainted: G           OE     5.3.5-050305-generic #201910071830
kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kernel: kworker/u65:9   D    0   494      2 0x80004000
kernel: Workqueue: nvme-wq nvme_scan_work [nvme_core]
kernel: Call Trace:
kernel:  __schedule+0x2b9/0x6c0
kernel:  schedule+0x42/0xb0
kernel:  schedule_preempt_disabled+0xe/0x10
kernel:  __mutex_lock.isra.0+0x182/0x4f0
kernel:  __mutex_lock_slowpath+0x13/0x20
kernel:  mutex_lock+0x2e/0x40
kernel:  revalidate_disk+0x63/0xa0
kernel:  __nvme_revalidate_disk+0xfe/0x110 [nvme_core]
kernel:  nvme_revalidate_disk+0xa4/0x160 [nvme_core]
kernel:  ? evict+0x14c/0x1b0
kernel:  revalidate_disk+0x2b/0xa0
kernel:  nvme_validate_ns+0x49/0x940 [nvme_core]
kernel:  ? blk_mq_free_request+0xd2/0x100
kernel:  ? __nvme_submit_sync_cmd+0xbe/0x1e0 [nvme_core]
kernel:  nvme_scan_work+0x24f/0x380 [nvme_core]
kernel:  process_one_work+0x1db/0x380
kernel:  worker_thread+0x249/0x400
kernel:  kthread+0x104/0x140
kernel:  ? process_one_work+0x380/0x380
kernel:  ? kthread_park+0x80/0x80
kernel:  ret_from_fork+0x1f/0x40
...
kernel: INFO: task kworker/u65:1:2630 blocked for more than 241 seconds.
kernel:       Tainted: G           OE     5.3.5-050305-generic #201910071830
kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kernel: kworker/u65:1   D    0  2630      2 0x80004000
kernel: Workqueue: nvme-wq nvme_scan_work [nvme_core]
kernel: Call Trace:
kernel:  __schedule+0x2b9/0x6c0
kernel:  schedule+0x42/0xb0
kernel:  io_schedule+0x16/0x40
kernel:  do_read_cache_page+0x438/0x830
kernel:  ? __switch_to_asm+0x34/0x70
kernel:  ? file_fdatawait_range+0x30/0x30
kernel:  read_cache_page+0x12/0x20
kernel:  read_dev_sector+0x27/0xc0
kernel:  read_lba+0xc1/0x220
kernel:  ? kmem_cache_alloc_trace+0x19c/0x230
kernel:  efi_partition+0x1e6/0x708
kernel:  ? vsnprintf+0x39e/0x4e0
kernel:  ? snprintf+0x49/0x60
kernel:  check_partition+0x154/0x244
kernel:  rescan_partitions+0xae/0x280
kernel:  __blkdev_get+0x40f/0x560
kernel:  blkdev_get+0x3d/0x140
kernel:  __device_add_disk+0x388/0x480
kernel:  device_add_disk+0x13/0x20
kernel:  nvme_mpath_set_live+0x119/0x140 [nvme_core]
kernel:  nvme_update_ns_ana_state+0x5c/0x60 [nvme_core]
kernel:  nvme_set_ns_ana_state+0x1e/0x30 [nvme_core]
kernel:  nvme_parse_ana_log+0xa1/0x180 [nvme_core]
kernel:  ? nvme_update_ns_ana_state+0x60/0x60 [nvme_core]
kernel:  nvme_mpath_add_disk+0x47/0x90 [nvme_core]
kernel:  nvme_validate_ns+0x396/0x940 [nvme_core]
kernel:  ? blk_mq_free_request+0xd2/0x100
kernel:  nvme_scan_work+0x24f/0x380 [nvme_core]
kernel:  process_one_work+0x1db/0x380
kernel:  worker_thread+0x249/0x400
kernel:  kthread+0x104/0x140
kernel:  ? process_one_work+0x380/0x380
kernel:  ? kthread_park+0x80/0x80
kernel:  ret_from_fork+0x1f/0x40

--

Fixes fab7772bfbcf ("nvme-multipath: revalidate nvme_ns_head gendisk

in nvme_validate_ns")

---
 drivers/nvme/host/core.c | 1 -
 1 file changed, 1 deletion(-)
drivers/nvme/host/core.c +0 -1
index faa7feebb6095..84fcfcdb8ba5f 100644
@@ -1599,7 +1599,6 @@ static void __nvme_revalidate_disk(struct gendisk *disk, struct nvme_id_ns *id)
 	if (ns->head->disk) {
 		nvme_update_disk_info(ns->head->disk, ns, id);
 		blk_queue_stack_limits(ns->head->disk->queue, ns->queue);
-		revalidate_disk(ns->head->disk);
 	}
 #endif
 }
Signature · 1 line
2.25.1
author maintainer
#200 lore raw

PATCH 198/206 scsi: libfc: Handling of extra kref

In reply to Sasha Levin

From: Javed Hasan <[email protected]>

[ Upstream commit 71f2bf85e90d938d4a9ef9dd9bfa8d9b0b6a03f7 ]

Handling of extra kref which is done by lookup table in case rdata is already present in list.

This issue was leading to memory leak. Trace from KMEMLEAK tool:

unreferenced object 0xffff8888259e8780 (size 512):

    comm "kworker/2:1", pid 182614, jiffies 4433237386 (age 113021.971s)
    hex dump (first 32 bytes):
    58 0a ec cf 83 88 ff ff 00 00 00 00 00 00 00 00
    01 00 00 00 08 00 00 00 13 7d f0 1e 0e 00 00 10
  backtrace:
	[<000000006b25760f>] fc_rport_recv_req+0x3c6/0x18f0 [libfc]
	[<00000000f208d994>] fc_lport_recv_els_req+0x120/0x8a0 [libfc]
	[<00000000a9c437b8>] fc_lport_recv+0xb9/0x130 [libfc]
	[<00000000ad5be37b>] qedf_ll2_process_skb+0x73d/0xad0 [qedf]
	[<00000000e0eb6893>] process_one_work+0x382/0x6c0
	[<000000002dfd9e21>] worker_thread+0x57/0x5c0
	[<00000000b648204f>] kthread+0x1a0/0x1c0
	[<0000000072f5ab20>] ret_from_fork+0x35/0x40
	[<000000001d5c05d8>] 0xffffffffffffffff

Below is the log sequence which leads to memory leak. Here we get the nested "Received PLOGI request" for same port and this request leads to call the fc_rport_create() twice for the same rport.

kernel: host1: rport fffce5: Received PLOGI request
kernel: host1: rport fffce5: Received PLOGI in INIT state
kernel: host1: rport fffce5: Port is Ready
kernel: host1: rport fffce5: Received PRLI request while in state Ready
kernel: host1: rport fffce5: PRLI rspp type 8 active 1 passive 0
kernel: host1: rport fffce5: Received LOGO request while in state Ready
kernel: host1: rport fffce5: Delete port
kernel: host1: rport fffce5: Received PLOGI request
kernel: host1: rport fffce5: Received PLOGI in state Delete - send busy

---
 drivers/scsi/libfc/fc_rport.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/scsi/libfc/fc_rport.c +3 -1
index 90a748551ede5..f39d2d62b002f 100644
@@ -145,8 +145,10 @@ struct fc_rport_priv *fc_rport_create(struct fc_lport *lport, u32 port_id)
 	lockdep_assert_held(&lport->disc.disc_mutex);
 
 	rdata = fc_rport_lookup(lport, port_id);
-	if (rdata)
+	if (rdata) {
+		kref_put(&rdata->kref, fc_rport_destroy);
 		return rdata;
+	}
 
 	if (lport->rport_priv_size > 0)
 		rport_priv_size = lport->rport_priv_size;
Signature · 1 line
2.25.1
author maintainer
#197 lore raw

PATCH 195/206 vfio/pci: Clear error and request eventfd ctx after releasing

In reply to Sasha Levin

From: Alex Williamson <[email protected]>

[ Upstream commit 5c5866c593bbd444d0339ede6a8fb5f14ff66d72 ]

The next use of the device will generate an underflow from the stale reference.

Cc Qian Cai <[email protected]>
Fixes 1518ac272e78 ("vfio/pci: fix memory leaks of eventfd ctx")
---
 drivers/vfio/pci/vfio_pci.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/vfio/pci/vfio_pci.c +6 -2
index 86cd8bdfa9f28..94fad366312f1 100644
@@ -409,10 +409,14 @@ static void vfio_pci_release(void *device_data)
 	if (!(--vdev->refcnt)) {
 		vfio_spapr_pci_eeh_release(vdev->pdev);
 		vfio_pci_disable(vdev);
-		if (vdev->err_trigger)
+		if (vdev->err_trigger) {
 			eventfd_ctx_put(vdev->err_trigger);
-		if (vdev->req_trigger)
+			vdev->err_trigger = NULL;
+		}
+		if (vdev->req_trigger) {
 			eventfd_ctx_put(vdev->req_trigger);
+			vdev->req_trigger = NULL;
+		}
 	}
 
 	mutex_unlock(&driver_lock);
Signature · 1 line
2.25.1
author maintainer
#206 lore raw

PATCH 204/206 perf parse-events: Use strcmp() to compare the PMU name

In reply to Sasha Levin

From: Jin Yao <[email protected]>

[ Upstream commit 8510895bafdbf7c4dd24c22946d925691135c2b2 ]

A big uncore event group is split into multiple small groups which only include the uncore events from the same PMU. This has been supported in the commit 3cdc5c2cb924a ("perf parse-events: Handle uncore event aliases in small groups properly").

If the event's PMU name starts to repeat, it must be a new event. That can be used to distinguish the leader from other members. But now it only compares the pointer of pmu_name (leader->pmu_name == evsel->pmu_name).

If we use "perf stat -M LLC_MISSES.PCIE_WRITE -a" on cascadelakex, the event list is:

evsel->name evsel->pmu_name
---------------------------------------------------------------
unc_iio_data_req_of_cpu.mem_write.part0 uncore_iio_4 (as leader)
unc_iio_data_req_of_cpu.mem_write.part0 uncore_iio_2
unc_iio_data_req_of_cpu.mem_write.part0 uncore_iio_0
unc_iio_data_req_of_cpu.mem_write.part0 uncore_iio_5
unc_iio_data_req_of_cpu.mem_write.part0 uncore_iio_3
unc_iio_data_req_of_cpu.mem_write.part0 uncore_iio_1
unc_iio_data_req_of_cpu.mem_write.part1 uncore_iio_4
......

For the event "unc_iio_data_req_of_cpu.mem_write.part1" with "uncore_iio_4", it should be the event from PMU "uncore_iio_4". It's not a new leader for this PMU.

But if we use "(leader->pmu_name == evsel->pmu_name)", the check would be failed and the event is stored to leaders[] as a new PMU leader.

So this patch uses strcmp to compare the PMU name between events.

Fixes d4953f7ef1a2 ("perf parse-events: Fix 3 use after frees found with clang ASAN")
Cc Alexander Shishkin <[email protected]>
Cc Andi Kleen <[email protected]>
Cc Jin Yao <[email protected]>
Cc Kan Liang <[email protected]>
Cc Peter Zijlstra <[email protected]>
---
 tools/perf/util/parse-events.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
tools/perf/util/parse-events.c +2 -3
index 426f1984c143e..5ab5c69f50500 100644
@@ -1423,12 +1423,11 @@ parse_events__set_leader_for_uncore_aliase(char *name, struct list_head *list,
 		 * event. That can be used to distinguish the leader from
 		 * other members, even they have the same event name.
 		 */
-		if ((leader != evsel) && (leader->pmu_name == evsel->pmu_name)) {
+		if ((leader != evsel) &&
+		    !strcmp(leader->pmu_name, evsel->pmu_name)) {
 			is_leader = false;
 			continue;
 		}
-		/* The name is always alias name */
-		WARN_ON(strcmp(leader->name, evsel->name));
 
 		/* Store the leader event for each PMU */
 		leaders[nr_pmu++] = (uintptr_t) evsel;
Signature · 1 line
2.25.1
author maintainer
#208 lore raw

PATCH 206/206 nvme: explicitly update mpath disk capacity on revalidation

In reply to Sasha Levin

From: Anthony Iliopoulos <[email protected]>

[ Upstream commit 05b29021fba5e725dd385151ef00b6340229b500 ]

Commit 3b4b19721ec652 ("nvme: fix possible deadlock when I/O is blocked") reverted multipath head disk revalidation due to deadlocks caused by holding the bd_mutex during revalidate.

Updating the multipath disk blockdev size is still required though for userspace to be able to observe any resizing while the device is mounted. Directly update the bdev inode size to avoid unnecessarily holding the bdev->bd_mutex.

Fixes 3b4b19721ec652 ("nvme: fix possible deadlock when I/O is

blocked")

---
 drivers/nvme/host/core.c |  1 +
 drivers/nvme/host/nvme.h | 13 +++++++++++++
 2 files changed, 14 insertions(+)
drivers/nvme/host/core.c +1 -0
index 84fcfcdb8ba5f..33dad9774da01 100644
@@ -1599,6 +1599,7 @@ static void __nvme_revalidate_disk(struct gendisk *disk, struct nvme_id_ns *id)
 	if (ns->head->disk) {
 		nvme_update_disk_info(ns->head->disk, ns, id);
 		blk_queue_stack_limits(ns->head->disk->queue, ns->queue);
+		nvme_mpath_update_disk_size(ns->head->disk);
 	}
 #endif
 }
drivers/nvme/host/nvme.h +13 -0
index a70b997060e68..9c2e7a151e400 100644
@@ -504,6 +504,16 @@ static inline void nvme_mpath_check_last_path(struct nvme_ns *ns)
 		kblockd_schedule_work(&head->requeue_work);
 }
 
+static inline void nvme_mpath_update_disk_size(struct gendisk *disk)
+{
+	struct block_device *bdev = bdget_disk(disk, 0);
+
+	if (bdev) {
+		bd_set_size(bdev, get_capacity(disk) << SECTOR_SHIFT);
+		bdput(bdev);
+	}
+}
+
 extern struct device_attribute dev_attr_ana_grpid;
 extern struct device_attribute dev_attr_ana_state;
 
@@ -570,6 +580,9 @@ static inline void nvme_mpath_wait_freeze(struct nvme_subsystem *subsys)
 static inline void nvme_mpath_start_freeze(struct nvme_subsystem *subsys)
 {
 }
+static inline void nvme_mpath_update_disk_size(struct gendisk *disk)
+{
+}
 #endif /* CONFIG_NVME_MULTIPATH */
 
 #ifdef CONFIG_NVM
Signature · 1 line
2.25.1
author maintainer
#166 lore raw

PATCH 164/206 ALSA: hda: Fix potential race in unsol event handler

In reply to Sasha Levin

From: Takashi Iwai <[email protected]>

[ Upstream commit c637fa151259c0f74665fde7cba5b7eac1417ae5 ]

The unsol event handling code has a loop retrieving the read/write indices and the arrays without locking while the append to the array may happen concurrently. This may lead to some inconsistency. Although there hasn't been any proof of this bad results, it's still safer to protect the racy accesses.

This patch adds the spinlock protection around the unsol handling loop for addressing it. Here we take bus->reg_lock as the writer side snd_hdac_bus_queue_event() is also protected by that lock.

---
 sound/hda/hdac_bus.c | 4 ++++
 1 file changed, 4 insertions(+)
sound/hda/hdac_bus.c +4 -0
index 714a51721a313..ab9236e4c157e 100644
@@ -155,6 +155,7 @@ static void process_unsol_events(struct work_struct *work)
 	struct hdac_driver *drv;
 	unsigned int rp, caddr, res;
 
+	spin_lock_irq(&bus->reg_lock);
 	while (bus->unsol_rp != bus->unsol_wp) {
 		rp = (bus->unsol_rp + 1) % HDA_UNSOL_QUEUE_SIZE;
 		bus->unsol_rp = rp;
@@ -166,10 +167,13 @@ static void process_unsol_events(struct work_struct *work)
 		codec = bus->caddr_tbl[caddr & 0x0f];
 		if (!codec || !codec->dev.driver)
 			continue;
+		spin_unlock_irq(&bus->reg_lock);
 		drv = drv_to_hdac_driver(codec->dev.driver);
 		if (drv->unsol_event)
 			drv->unsol_event(codec, res);
+		spin_lock_irq(&bus->reg_lock);
 	}
+	spin_unlock_irq(&bus->reg_lock);
 }
 
 /**
Signature · 1 line
2.25.1
author maintainer
#187 lore raw

PATCH 185/206 ASoC: img-i2s-out: Fix runtime PM imbalance on error

In reply to Sasha Levin

From: Dinghao Liu <[email protected]>

[ Upstream commit 65bd91dd6957390c42a0491b9622cf31a2cdb140 ]

pm_runtime_get_sync() increments the runtime PM usage counter even the call returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced.

---
 sound/soc/img/img-i2s-out.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
sound/soc/img/img-i2s-out.c +6 -2
index fc2d1dac63339..798ab579564cb 100644
@@ -350,8 +350,10 @@ static int img_i2s_out_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
 	chan_control_mask = IMG_I2S_OUT_CHAN_CTL_CLKT_MASK;
 
 	ret = pm_runtime_get_sync(i2s->dev);
-	if (ret < 0)
+	if (ret < 0) {
+		pm_runtime_put_noidle(i2s->dev);
 		return ret;
+	}
 
 	img_i2s_out_disable(i2s);
 
@@ -491,8 +493,10 @@ static int img_i2s_out_probe(struct platform_device *pdev)
 			goto err_pm_disable;
 	}
 	ret = pm_runtime_get_sync(&pdev->dev);
-	if (ret < 0)
+	if (ret < 0) {
+		pm_runtime_put_noidle(&pdev->dev);
 		goto err_suspend;
+	}
 
 	reg = IMG_I2S_OUT_CTL_FRM_SIZE_MASK;
 	img_i2s_out_writel(i2s, reg, IMG_I2S_OUT_CTL);
Signature · 1 line
2.25.1
author maintainer
#26 lore raw

PATCH 27/206 dmaengine: mediatek: hsdma_probe: fixed a memory leak when devm_request_irq fails

In reply to Sasha Levin

From: Satendra Singh Thakur <[email protected]>

[ Upstream commit 1ff95243257fad07290dcbc5f7a6ad79d6e703e2 ]

When devm_request_irq fails, currently, the function dma_async_device_unregister gets called. This doesn't free the resources allocated by of_dma_controller_register. Therefore, we have called of_dma_controller_free for this purpose.

---
 drivers/dma/mediatek/mtk-hsdma.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/dma/mediatek/mtk-hsdma.c +3 -1
index b7ec56ae02a6e..fca232b1d4a64 100644
@@ -997,7 +997,7 @@ static int mtk_hsdma_probe(struct platform_device *pdev)
 	if (err) {
 		dev_err(&pdev->dev,
 			"request_irq failed with err %d\n", err);
-		goto err_unregister;
+		goto err_free;
 	}
 
 	platform_set_drvdata(pdev, hsdma);
@@ -1006,6 +1006,8 @@ static int mtk_hsdma_probe(struct platform_device *pdev)
 
 	return 0;
 
+err_free:
+	of_dma_controller_free(pdev->dev.of_node);
 err_unregister:
 	dma_async_device_unregister(dd);
 
Signature · 7 lines
2.25.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
author maintainer
#19 lore raw

PATCH 20/206 mtd: cfi_cmdset_0002: don't free cfi->cfiq in error path of cfi_amdstd_setup()

In reply to Sasha Levin

From: Hou Tao <[email protected]>

[ Upstream commit 03976af89e3bd9489d542582a325892e6a8cacc0 ]

Else there may be a double-free problem, because cfi->cfiq will be freed by mtd_do_chip_probe() if both the two invocations of check_cmd_set() return failure.

---
 drivers/mtd/chips/cfi_cmdset_0002.c | 1 -
 1 file changed, 1 deletion(-)
drivers/mtd/chips/cfi_cmdset_0002.c +0 -1
index 1dbc9554a0786..3ab75d3e2ce32 100644
@@ -727,7 +727,6 @@ static struct mtd_info *cfi_amdstd_setup(struct mtd_info *mtd)
 	kfree(mtd->eraseregions);
 	kfree(mtd);
 	kfree(cfi->cmdset_priv);
-	kfree(cfi->cfiq);
 	return NULL;
 }
 
Signature · 6 lines
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
author maintainer
#32 lore raw

PATCH 33/206 ubi: Fix producing anchor PEBs

In reply to Sasha Levin

From: Sascha Hauer <[email protected]>

[ Upstream commit f9c34bb529975fe9f85b870a80c53a83a3c5a182 ]

When a new fastmap is about to be written UBI must make sure it has a free block for a fastmap anchor available. For this ubi_update_fastmap() calls ubi_ensure_anchor_pebs(). This stopped working with 2e8f08deabbc ("ubi: Fix races around ubi_refill_pools()"), with this commit the wear leveling code is blocked and can no longer produce free PEBs. UBI then more often than not falls back to write the new fastmap anchor to the same block it was already on which means the same erase block gets erased during each fastmap write and wears out quite fast.

As the locking prevents us from producing the anchor PEB when we actually need it, this patch changes the strategy for creating the anchor PEB. We no longer create it on demand right before we want to write a fastmap, but instead we create an anchor PEB right after we have written a fastmap. This gives us enough time to produce a new anchor PEB before it is needed. To make sure we have an anchor PEB for the very first fastmap write we call ubi_ensure_anchor_pebs() during initialisation as well.

Fixes 2e8f08deabbc ("ubi: Fix races around ubi_refill_pools()")
---
 drivers/mtd/ubi/fastmap-wl.c | 31 ++++++++++++++++++-------------
 drivers/mtd/ubi/fastmap.c    | 14 +++++---------
 drivers/mtd/ubi/ubi.h        |  6 ++++--
 drivers/mtd/ubi/wl.c         | 32 ++++++++++++++------------------
 drivers/mtd/ubi/wl.h         |  1 -
 5 files changed, 41 insertions(+), 43 deletions(-)
drivers/mtd/ubi/fastmap-wl.c +18 -13
index 98f7d6be8d1fc..13efebb400225 100644
@@ -66,18 +66,6 @@ static void return_unused_pool_pebs(struct ubi_device *ubi,
 	}
 }
 
-static int anchor_pebs_available(struct rb_root *root)
-{
-	struct rb_node *p;
-	struct ubi_wl_entry *e;
-
-	ubi_rb_for_each_entry(p, e, root, u.rb)
-		if (e->pnum < UBI_FM_MAX_START)
-			return 1;
-
-	return 0;
-}
-
 /**
  * ubi_wl_get_fm_peb - find a physical erase block with a given maximal number.
  * @ubi: UBI device description object
@@ -286,8 +274,26 @@ static struct ubi_wl_entry *get_peb_for_wl(struct ubi_device *ubi)
 int ubi_ensure_anchor_pebs(struct ubi_device *ubi)
 {
 	struct ubi_work *wrk;
+	struct ubi_wl_entry *anchor;
 
 	spin_lock(&ubi->wl_lock);
+
+	/* Do we already have an anchor? */
+	if (ubi->fm_anchor) {
+		spin_unlock(&ubi->wl_lock);
+		return 0;
+	}
+
+	/* See if we can find an anchor PEB on the list of free PEBs */
+	anchor = ubi_wl_get_fm_peb(ubi, 1);
+	if (anchor) {
+		ubi->fm_anchor = anchor;
+		spin_unlock(&ubi->wl_lock);
+		return 0;
+	}
+
+	/* No luck, trigger wear leveling to produce a new anchor PEB */
+	ubi->fm_do_produce_anchor = 1;
 	if (ubi->wl_scheduled) {
 		spin_unlock(&ubi->wl_lock);
 		return 0;
@@ -303,7 +309,6 @@ int ubi_ensure_anchor_pebs(struct ubi_device *ubi)
 		return -ENOMEM;
 	}
 
-	wrk->anchor = 1;
 	wrk->func = &wear_leveling_worker;
 	__schedule_ubi_work(ubi, wrk);
 	return 0;
drivers/mtd/ubi/fastmap.c +5 -9
index 8e292992f84c7..b88ef875236cc 100644
@@ -1552,14 +1552,6 @@ int ubi_update_fastmap(struct ubi_device *ubi)
 		return 0;
 	}
 
-	ret = ubi_ensure_anchor_pebs(ubi);
-	if (ret) {
-		up_write(&ubi->fm_eba_sem);
-		up_write(&ubi->work_sem);
-		up_write(&ubi->fm_protect);
-		return ret;
-	}
-
 	new_fm = kzalloc(sizeof(*new_fm), GFP_KERNEL);
 	if (!new_fm) {
 		up_write(&ubi->fm_eba_sem);
@@ -1630,7 +1622,8 @@ int ubi_update_fastmap(struct ubi_device *ubi)
 	}
 
 	spin_lock(&ubi->wl_lock);
-	tmp_e = ubi_wl_get_fm_peb(ubi, 1);
+	tmp_e = ubi->fm_anchor;
+	ubi->fm_anchor = NULL;
 	spin_unlock(&ubi->wl_lock);
 
 	if (old_fm) {
@@ -1682,6 +1675,9 @@ out_unlock:
 	up_write(&ubi->work_sem);
 	up_write(&ubi->fm_protect);
 	kfree(old_fm);
+
+	ubi_ensure_anchor_pebs(ubi);
+
 	return ret;
 
 err:
drivers/mtd/ubi/ubi.h +4 -2
index d47b9e436e673..d248ec371cc17 100644
@@ -504,6 +504,8 @@ struct ubi_debug_info {
  * @fm_work: fastmap work queue
  * @fm_work_scheduled: non-zero if fastmap work was scheduled
  * @fast_attach: non-zero if UBI was attached by fastmap
+ * @fm_anchor: The next anchor PEB to use for fastmap
+ * @fm_do_produce_anchor: If true produce an anchor PEB in wl
  *
  * @used: RB-tree of used physical eraseblocks
  * @erroneous: RB-tree of erroneous used physical eraseblocks
@@ -612,6 +614,8 @@ struct ubi_device {
 	struct work_struct fm_work;
 	int fm_work_scheduled;
 	int fast_attach;
+	struct ubi_wl_entry *fm_anchor;
+	int fm_do_produce_anchor;
 
 	/* Wear-leveling sub-system's stuff */
 	struct rb_root used;
@@ -802,7 +806,6 @@ struct ubi_attach_info {
  * @vol_id: the volume ID on which this erasure is being performed
  * @lnum: the logical eraseblock number
  * @torture: if the physical eraseblock has to be tortured
- * @anchor: produce a anchor PEB to by used by fastmap
  *
  * The @func pointer points to the worker function. If the @shutdown argument is
  * not zero, the worker has to free the resources and exit immediately as the
@@ -818,7 +821,6 @@ struct ubi_work {
 	int vol_id;
 	int lnum;
 	int torture;
-	int anchor;
 };
 
 #include "debug.h"
drivers/mtd/ubi/wl.c +14 -18
index 6f2ac865ff05e..80d64d7e7a8be 100644
@@ -331,13 +331,6 @@ static struct ubi_wl_entry *find_wl_entry(struct ubi_device *ubi,
 		}
 	}
 
-	/* If no fastmap has been written and this WL entry can be used
-	 * as anchor PEB, hold it back and return the second best WL entry
-	 * such that fastmap can use the anchor PEB later. */
-	if (prev_e && !ubi->fm_disabled &&
-	    !ubi->fm && e->pnum < UBI_FM_MAX_START)
-		return prev_e;
-
 	return e;
 }
 
@@ -648,9 +641,6 @@ static int wear_leveling_worker(struct ubi_device *ubi, struct ubi_work *wrk,
 {
 	int err, scrubbing = 0, torture = 0, protect = 0, erroneous = 0;
 	int erase = 0, keep = 0, vol_id = -1, lnum = -1;
-#ifdef CONFIG_MTD_UBI_FASTMAP
-	int anchor = wrk->anchor;
-#endif
 	struct ubi_wl_entry *e1, *e2;
 	struct ubi_vid_io_buf *vidb;
 	struct ubi_vid_hdr *vid_hdr;
@@ -690,11 +680,7 @@ static int wear_leveling_worker(struct ubi_device *ubi, struct ubi_work *wrk,
 	}
 
 #ifdef CONFIG_MTD_UBI_FASTMAP
-	/* Check whether we need to produce an anchor PEB */
-	if (!anchor)
-		anchor = !anchor_pebs_available(&ubi->free);
-
-	if (anchor) {
+	if (ubi->fm_do_produce_anchor) {
 		e1 = find_anchor_wl_entry(&ubi->used);
 		if (!e1)
 			goto out_cancel;
@@ -705,6 +691,7 @@ static int wear_leveling_worker(struct ubi_device *ubi, struct ubi_work *wrk,
 		self_check_in_wl_tree(ubi, e1, &ubi->used);
 		rb_erase(&e1->u.rb, &ubi->used);
 		dbg_wl("anchor-move PEB %d to PEB %d", e1->pnum, e2->pnum);
+		ubi->fm_do_produce_anchor = 0;
 	} else if (!ubi->scrub.rb_node) {
 #else
 	if (!ubi->scrub.rb_node) {
@@ -1037,7 +1024,6 @@ static int ensure_wear_leveling(struct ubi_device *ubi, int nested)
 		goto out_cancel;
 	}
 
-	wrk->anchor = 0;
 	wrk->func = &wear_leveling_worker;
 	if (nested)
 		__schedule_ubi_work(ubi, wrk);
@@ -1079,8 +1065,15 @@ static int __erase_worker(struct ubi_device *ubi, struct ubi_work *wl_wrk)
 	err = sync_erase(ubi, e, wl_wrk->torture);
 	if (!err) {
 		spin_lock(&ubi->wl_lock);
-		wl_tree_add(e, &ubi->free);
-		ubi->free_count++;
+
+		if (!ubi->fm_anchor && e->pnum < UBI_FM_MAX_START) {
+			ubi->fm_anchor = e;
+			ubi->fm_do_produce_anchor = 0;
+		} else {
+			wl_tree_add(e, &ubi->free);
+			ubi->free_count++;
+		}
+
 		spin_unlock(&ubi->wl_lock);
 
 		/*
@@ -1724,6 +1717,9 @@ int ubi_wl_init(struct ubi_device *ubi, struct ubi_attach_info *ai)
 	if (err)
 		goto out_free;
 
+#ifdef CONFIG_MTD_UBI_FASTMAP
+	ubi_ensure_anchor_pebs(ubi);
+#endif
 	return 0;
 
 out_free:
drivers/mtd/ubi/wl.h +0 -1
index a9e2d669acd81..c93a532937863 100644
@@ -2,7 +2,6 @@
 #ifndef UBI_WL_H
 #define UBI_WL_H
 #ifdef CONFIG_MTD_UBI_FASTMAP
-static int anchor_pebs_available(struct rb_root *root);
 static void update_fastmap_work_fn(struct work_struct *wrk);
 static struct ubi_wl_entry *find_anchor_wl_entry(struct rb_root *root);
 static struct ubi_wl_entry *get_peb_for_wl(struct ubi_device *ubi);
Signature · 6 lines
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
author maintainer
#49 lore raw

PATCH 50/206 scsi: ufs: Make ufshcd_add_command_trace() easier to read

In reply to Sasha Levin

From: Bart Van Assche <[email protected]>

[ Upstream commit e4d2add7fd5bc64ee3e388eabe6b9e081cb42e11 ]

Since the lrbp->cmd expression occurs multiple times, introduce a new local variable to hold that pointer. This patch does not change any functionality.

---
 drivers/scsi/ufs/ufshcd.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/scsi/ufs/ufshcd.c +6 -6
index eb10a5cacd90c..faf1959981784 100644
@@ -353,27 +353,27 @@ static void ufshcd_add_command_trace(struct ufs_hba *hba,
 	u8 opcode = 0;
 	u32 intr, doorbell;
 	struct ufshcd_lrb *lrbp = &hba->lrb[tag];
+	struct scsi_cmnd *cmd = lrbp->cmd;
 	int transfer_len = -1;
 
 	if (!trace_ufshcd_command_enabled()) {
 		/* trace UPIU W/O tracing command */
-		if (lrbp->cmd)
+		if (cmd)
 			ufshcd_add_cmd_upiu_trace(hba, tag, str);
 		return;
 	}
 
-	if (lrbp->cmd) { /* data phase exists */
+	if (cmd) { /* data phase exists */
 		/* trace UPIU also */
 		ufshcd_add_cmd_upiu_trace(hba, tag, str);
-		opcode = (u8)(*lrbp->cmd->cmnd);
+		opcode = cmd->cmnd[0];
 		if ((opcode == READ_10) || (opcode == WRITE_10)) {
 			/*
 			 * Currently we only fully trace read(10) and write(10)
 			 * commands
 			 */
-			if (lrbp->cmd->request && lrbp->cmd->request->bio)
-				lba =
-				  lrbp->cmd->request->bio->bi_iter.bi_sector;
+			if (cmd->request && cmd->request->bio)
+				lba = cmd->request->bio->bi_iter.bi_sector;
 			transfer_len = be32_to_cpu(
 				lrbp->ucd_req_ptr->sc.exp_data_transfer_len);
 		}
Signature · 7 lines
2.25.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
author maintainer
#50 lore raw

PATCH 51/206 scsi: ufs: Fix a race condition in the tracing code

In reply to Sasha Levin

From: Bart Van Assche <[email protected]>

[ Upstream commit eacf36f5bebde5089dddb3d5bfcbeab530b01f8a ]

Starting execution of a command before tracing a command may cause the completion handler to free data while it is being traced. Fix this race by tracing a command before it is submitted.

---
 drivers/scsi/ufs/ufshcd.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/scsi/ufs/ufshcd.c +1 -1
index faf1959981784..b2cbdd01ab10b 100644
@@ -1910,12 +1910,12 @@ void ufshcd_send_command(struct ufs_hba *hba, unsigned int task_tag)
 {
 	hba->lrb[task_tag].issue_time_stamp = ktime_get();
 	hba->lrb[task_tag].compl_time_stamp = ktime_set(0, 0);
+	ufshcd_add_command_trace(hba, task_tag, "send");
 	ufshcd_clk_scaling_start_busy(hba);
 	__set_bit(task_tag, &hba->outstanding_reqs);
 	ufshcd_writel(hba, 1 << task_tag, REG_UTP_TRANSFER_REQ_DOOR_BELL);
 	/* Make sure that doorbell is committed immediately */
 	wmb();
-	ufshcd_add_command_trace(hba, task_tag, "send");
 }
 
 /**
Signature · 7 lines
2.25.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
author maintainer
#80 lore raw

PATCH 79/206 mt76: clear skb pointers from rx aggregation reorder buffer during cleanup

In reply to Sasha Levin

From: Felix Fietkau <[email protected]>

[ Upstream commit 9379df2fd9234e3b67a23101c2370c99f6af6d77 ]

During the cleanup of the aggregation session, a rx handler (or release timer) on another CPU might still hold a pointer to the reorder buffer and could attempt to release some packets.
Clearing pointers during cleanup avoids a theoretical use-after-free bug here.

---
 drivers/net/wireless/mediatek/mt76/agg-rx.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/wireless/mediatek/mt76/agg-rx.c +1 -0
index d44d57e6eb27a..97df6b3a472b1 100644
@@ -278,6 +278,7 @@ static void mt76_rx_aggr_shutdown(struct mt76_dev *dev, struct mt76_rx_tid *tid)
 		if (!skb)
 			continue;
 
+		tid->reorder_buf[i] = NULL;
 		tid->nframes--;
 		dev_kfree_skb(skb);
 	}
Signature · 7 lines
2.25.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
author maintainer
#61 lore raw

PATCH 60/206 ARM: 8948/1: Prevent OOB access in stacktrace

In reply to Sasha Levin

From: Vincent Whitchurch <[email protected]>

[ Upstream commit 40ff1ddb5570284e039e0ff14d7a859a73dc3673 ]

The stacktrace code can read beyond the stack size, when it attempts to read pt_regs from exception frames.

This can happen on normal, non-corrupt stacks. Since the unwind information in the extable is not correct for function prologues, the unwinding code can return data from the stack which is not actually the caller function address, and if in_entry_text() happens to succeed on this value, we can end up reading data from outside the task's stack when attempting to read pt_regs, since there is no bounds check.

Example:

[<8010e729>] (unwind_backtrace) from [<8010a9c9>] (show_stack+0x11/0x14) [<8010a9c9>] (show_stack) from [<8057d8d7>] (dump_stack+0x87/0xac) [<8057d8d7>] (dump_stack) from [<8012271d>] (tasklet_action_common.constprop.4+0xa5/0xa8) [<8012271d>] (tasklet_action_common.constprop.4) from [<80102333>] (__do_softirq+0x11b/0x31c) [<80102333>] (__do_softirq) from [<80122485>] (irq_exit+0xad/0xd8) [<80122485>] (irq_exit) from [<8015f3d7>] (__handle_domain_irq+0x47/0x84) [<8015f3d7>] (__handle_domain_irq) from [<8036a523>] (gic_handle_irq+0x43/0x78) [<8036a523>] (gic_handle_irq) from [<80101a49>] (__irq_svc+0x69/0xb4)

 Exception stack(0xeb491f58 to 0xeb491fa0)
 1f40:                                                       7eb14794 00000000
 1f60: ffffffff 008dd32c 008dd324 ffffffff 008dd314 0000002a 801011e4 eb490000
 1f80: 0000002a 7eb1478c 50c5387d eb491fa8 80101001 8023d09c 40080033 ffffffff
 [<80101a49>] (__irq_svc) from [<8023d09c>] (do_pipe2+0x0/0xac)
 [<8023d09c>] (do_pipe2) from [<ffffffff>] (0xffffffff)
 Exception stack(0xeb491fc8 to 0xeb492010)
 1fc0:                   008dd314 0000002a 00511ad8 008de4c8 7eb14790 7eb1478c
 1fe0: 00511e34 7eb14774 004c8557 76f44098 60080030 7eb14794 00000000 00000000
 2000: 00000001 00000000 ea846c00 ea847cc0

In this example, the stack limit is 0xeb492000, but 16 bytes outside the stack have been read.

Fix it by adding bounds checks.

---
 arch/arm/kernel/stacktrace.c | 2 ++
 arch/arm/kernel/traps.c      | 6 ++++--
 2 files changed, 6 insertions(+), 2 deletions(-)
arch/arm/kernel/stacktrace.c +2 -0
index a4d4a28fe07df..d23ab9ec130a3 100644
@@ -115,6 +115,8 @@ static int save_trace(struct stackframe *frame, void *d)
 		return 0;
 
 	regs = (struct pt_regs *)frame->sp;
+	if ((unsigned long)&regs[1] > ALIGN(frame->sp, THREAD_SIZE))
+		return 0;
 
 	trace->entries[trace->nr_entries++] = regs->ARM_pc;
 
arch/arm/kernel/traps.c +4 -2
index badf02ca36938..aec533168f046 100644
@@ -67,14 +67,16 @@ static void dump_mem(const char *, const char *, unsigned long, unsigned long);
 
 void dump_backtrace_entry(unsigned long where, unsigned long from, unsigned long frame)
 {
+	unsigned long end = frame + 4 + sizeof(struct pt_regs);
+
 #ifdef CONFIG_KALLSYMS
 	printk("[<%08lx>] (%ps) from [<%08lx>] (%pS)\n", where, (void *)where, from, (void *)from);
 #else
 	printk("Function entered at [<%08lx>] from [<%08lx>]\n", where, from);
 #endif
 
-	if (in_entry_text(from))
-		dump_mem("", "Exception stack", frame + 4, frame + 4 + sizeof(struct pt_regs));
+	if (in_entry_text(from) && end <= ALIGN(frame, THREAD_SIZE))
+		dump_mem("", "Exception stack", frame + 4, end);
 }
 
 void dump_backtrace_stm(u32 *stack, u32 instruction)
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#85 lore raw

PATCH 84/206 dmaengine: stm32-mdma: use vchan_terminate_vdesc() in .terminate_all

In reply to Sasha Levin

From: Amelie Delaunay <[email protected]>

[ Upstream commit dfc708812a2acfc0ca56f56233b3c3e7b0d4ffe7 ]

To avoid race with vchan_complete, use the race free way to terminate running transfer.

Move vdesc->node list_del in stm32_mdma_start_transfer instead of in stm32_mdma_xfer_end to avoid another race in vchan_dma_desc_free_list.

---
 drivers/dma/stm32-mdma.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/dma/stm32-mdma.c +6 -3
index 8c3c3e5b812a8..9c6867916e890 100644
@@ -1137,6 +1137,8 @@ static void stm32_mdma_start_transfer(struct stm32_mdma_chan *chan)
 		return;
 	}
 
+	list_del(&vdesc->node);
+
 	chan->desc = to_stm32_mdma_desc(vdesc);
 	hwdesc = chan->desc->node[0].hwdesc;
 	chan->curr_hwdesc = 0;
@@ -1252,8 +1254,10 @@ static int stm32_mdma_terminate_all(struct dma_chan *c)
 	LIST_HEAD(head);
 
 	spin_lock_irqsave(&chan->vchan.lock, flags);
-	if (chan->busy) {
-		stm32_mdma_stop(chan);
+	if (chan->desc) {
+		vchan_terminate_vdesc(&chan->desc->vdesc);
+		if (chan->busy)
+			stm32_mdma_stop(chan);
 		chan->desc = NULL;
 	}
 	vchan_get_all_descriptors(&chan->vchan, &head);
@@ -1341,7 +1345,6 @@ static enum dma_status stm32_mdma_tx_status(struct dma_chan *c,
 
 static void stm32_mdma_xfer_end(struct stm32_mdma_chan *chan)
 {
-	list_del(&chan->desc->vdesc.node);
 	vchan_cookie_complete(&chan->desc->vdesc);
 	chan->desc = NULL;
 	chan->busy = false;
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#89 lore raw

PATCH 88/206 dmaengine: stm32-dma: use vchan_terminate_vdesc() in .terminate_all

In reply to Sasha Levin

From: Amelie Delaunay <[email protected]>

[ Upstream commit d80cbef35bf89b763f06e03bb4ff8f933bf012c5 ]

To avoid race with vchan_complete, use the race free way to terminate running transfer.

Move vdesc->node list_del in stm32_dma_start_transfer instead of in stm32_mdma_chan_complete to avoid another race in vchan_dma_desc_free_list.

---
 drivers/dma/stm32-dma.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/dma/stm32-dma.c +6 -3
index 4903a408fc146..ac7af440f8658 100644
@@ -494,8 +494,10 @@ static int stm32_dma_terminate_all(struct dma_chan *c)
 
 	spin_lock_irqsave(&chan->vchan.lock, flags);
 
-	if (chan->busy) {
-		stm32_dma_stop(chan);
+	if (chan->desc) {
+		vchan_terminate_vdesc(&chan->desc->vdesc);
+		if (chan->busy)
+			stm32_dma_stop(chan);
 		chan->desc = NULL;
 	}
 
@@ -551,6 +553,8 @@ static void stm32_dma_start_transfer(struct stm32_dma_chan *chan)
 		if (!vdesc)
 			return;
 
+		list_del(&vdesc->node);
+
 		chan->desc = to_stm32_dma_desc(vdesc);
 		chan->next_sg = 0;
 	}
@@ -628,7 +632,6 @@ static void stm32_dma_handle_chan_done(struct stm32_dma_chan *chan)
 		} else {
 			chan->busy = false;
 			if (chan->next_sg == chan->desc->num_sgs) {
-				list_del(&chan->desc->vdesc.node);
 				vchan_cookie_complete(&chan->desc->vdesc);
 				chan->desc = NULL;
 			}
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#195 lore raw

PATCH 193/206 mtd: parser: cmdline: Support MTD names containing one or more colons

In reply to Sasha Levin

From: Boris Brezillon <[email protected]>

[ Upstream commit eb13fa0227417e84aecc3bd9c029d376e33474d3 ]

Looks like some drivers define MTD names with a colon in it, thus making mtdpart= parsing impossible. Let's fix the parser to gracefully handle that case: the last ':' in a partition definition sequence is considered instead of the first one.

---
 drivers/mtd/cmdlinepart.c | 23 ++++++++++++++++++++---
 1 file changed, 20 insertions(+), 3 deletions(-)
drivers/mtd/cmdlinepart.c +20 -3
index 3ea44cff9b759..c29205ee82e20 100644
@@ -231,12 +231,29 @@ static int mtdpart_setup_real(char *s)
 		struct cmdline_mtd_partition *this_mtd;
 		struct mtd_partition *parts;
 		int mtd_id_len, num_parts;
-		char *p, *mtd_id;
+		char *p, *mtd_id, *semicol;
+
+		/*
+		 * Replace the first ';' by a NULL char so strrchr can work
+		 * properly.
+		 */
+		semicol = strchr(s, ';');
+		if (semicol)
+			*semicol = '\0';
 
 		mtd_id = s;
 
-		/* fetch <mtd-id> */
-		p = strchr(s, ':');
+		/*
+		 * fetch <mtd-id>. We use strrchr to ignore all ':' that could
+		 * be present in the MTD name, only the last one is interpreted
+		 * as an <mtd-id>/<part-definition> separator.
+		 */
+		p = strrchr(s, ':');
+
+		/* Restore the ';' now. */
+		if (semicol)
+			*semicol = ';';
+
 		if (!p) {
 			pr_err("no mtd-id\n");
 			return -EINVAL;
Signature · 6 lines
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
author maintainer
#155 lore raw

PATCH 153/206 arm64: cpufeature: Relax checks for AArch32 support at EL[0-2]

In reply to Sasha Levin

From: Will Deacon <[email protected]>

[ Upstream commit 98448cdfe7060dd5491bfbd3f7214ffe1395d58e ]

We don't need to be quite as strict about mismatched AArch32 support, which is good because the friendly hardware folks have been busy mismatching this to their hearts' content.

* We don't care about EL2 or EL3 (there are silly comments concerning the latter, so remove those)

* EL1 support is gated by the ARM64_HAS_32BIT_EL1 capability and handled gracefully when a mismatch occurs

* EL0 support is gated by the ARM64_HAS_32BIT_EL0 capability and handled gracefully when a mismatch occurs

Relax the AArch32 checks to FTR_NONSTRICT.

---
 arch/arm64/kernel/cpufeature.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)
arch/arm64/kernel/cpufeature.c +3 -7
index ac3126aba0368..095dec566275f 100644
@@ -155,11 +155,10 @@ static const struct arm64_ftr_bits ftr_id_aa64pfr0[] = {
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_GIC_SHIFT, 4, 0),
 	S_ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_ASIMD_SHIFT, 4, ID_AA64PFR0_ASIMD_NI),
 	S_ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_FP_SHIFT, 4, ID_AA64PFR0_FP_NI),
-	/* Linux doesn't care about the EL3 */
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL3_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL2_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_SHIFT, 4, ID_AA64PFR0_EL1_64BIT_ONLY),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL0_SHIFT, 4, ID_AA64PFR0_EL0_64BIT_ONLY),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL2_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_SHIFT, 4, ID_AA64PFR0_EL1_64BIT_ONLY),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL0_SHIFT, 4, ID_AA64PFR0_EL0_64BIT_ONLY),
 	ARM64_FTR_END,
 };
 
@@ -671,9 +670,6 @@ void update_cpu_features(int cpu,
 	taint |= check_update_ftr_reg(SYS_ID_AA64MMFR2_EL1, cpu,
 				      info->reg_id_aa64mmfr2, boot->reg_id_aa64mmfr2);
 
-	/*
-	 * EL3 is not our concern.
-	 */
 	taint |= check_update_ftr_reg(SYS_ID_AA64PFR0_EL1, cpu,
 				      info->reg_id_aa64pfr0, boot->reg_id_aa64pfr0);
 	taint |= check_update_ftr_reg(SYS_ID_AA64PFR1_EL1, cpu,
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#171 lore raw

PATCH 169/206 arm64/cpufeature: Drop TraceFilt feature exposure from ID_DFR0 register

In reply to Sasha Levin

From: Anshuman Khandual <[email protected]>

[ Upstream commit 1ed1b90a0594c8c9d31e8bb8be25a2b37717dc9e ]

ID_DFR0 based TraceFilt feature should not be exposed to guests. Hence lets drop it.

Cc Catalin Marinas <[email protected]>
Cc Will Deacon <[email protected]>
Cc Marc Zyngier <[email protected]>
Cc Mark Rutland <[email protected]>
Cc James Morse <[email protected]>
Cc Suzuki K Poulose <[email protected]>
---
 arch/arm64/kernel/cpufeature.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/kernel/cpufeature.c +1 -1
index 095dec566275f..de6fa9b4abfa0 100644
@@ -300,7 +300,7 @@ static const struct arm64_ftr_bits ftr_id_pfr0[] = {
 };
 
 static const struct arm64_ftr_bits ftr_id_dfr0[] = {
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, 28, 4, 0),
+	/* [31:28] TraceFilt */
 	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, 24, 4, 0xf),	/* PerfMon */
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, 20, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, 16, 4, 0),
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#205 lore raw

PATCH 203/206 ubi: fastmap: Free unused fastmap anchor peb during detach

In reply to Sasha Levin

From: Hou Tao <[email protected]>

[ Upstream commit c16f39d14a7e0ec59881fbdb22ae494907534384 ]

When CONFIG_MTD_UBI_FASTMAP is enabled, fm_anchor will be assigned a free PEB during ubi_wl_init() or ubi_update_fastmap(). However if fastmap is not used or disabled on the MTD device, ubi_wl_entry related with the PEB will not be freed during detach.

So Fix it by freeing the unused fastmap anchor during detach.

Fixes f9c34bb52997 ("ubi: Fix producing anchor PEBs")
Reported-by [email protected]
---
 drivers/mtd/ubi/fastmap-wl.c | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)
drivers/mtd/ubi/fastmap-wl.c +13 -2
index 13efebb400225..e08f6b4637dda 100644
@@ -48,6 +48,13 @@ static struct ubi_wl_entry *find_anchor_wl_entry(struct rb_root *root)
 	return victim;
 }
 
+static inline void return_unused_peb(struct ubi_device *ubi,
+				     struct ubi_wl_entry *e)
+{
+	wl_tree_add(e, &ubi->free);
+	ubi->free_count++;
+}
+
 /**
  * return_unused_pool_pebs - returns unused PEB to the free tree.
  * @ubi: UBI device description object
@@ -61,8 +68,7 @@ static void return_unused_pool_pebs(struct ubi_device *ubi,
 
 	for (i = pool->used; i < pool->size; i++) {
 		e = ubi->lookuptbl[pool->pebs[i]];
-		wl_tree_add(e, &ubi->free);
-		ubi->free_count++;
+		return_unused_peb(ubi, e);
 	}
 }
 
@@ -370,6 +376,11 @@ static void ubi_fastmap_close(struct ubi_device *ubi)
 	return_unused_pool_pebs(ubi, &ubi->fm_pool);
 	return_unused_pool_pebs(ubi, &ubi->fm_wl_pool);
 
+	if (ubi->fm_anchor) {
+		return_unused_peb(ubi, ubi->fm_anchor);
+		ubi->fm_anchor = NULL;
+	}
+
 	if (ubi->fm) {
 		for (i = 0; i < ubi->fm->used_blocks; i++)
 			kfree(ubi->fm->e[i]);
Signature · 6 lines
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
author maintainer
#54 lore raw

PATCH 55/206 powerpc/powernv/ioda: Fix ref count for devices with their own PE

In reply to Sasha Levin

From: Frederic Barrat <[email protected]>

[ Upstream commit 05dd7da76986937fb288b4213b1fa10dbe0d1b33 ]

The pci_dn structure used to store a pointer to the struct pci_dev, so taking a reference on the device was required. However, the pci_dev pointer was later removed from the pci_dn structure, but the reference was kept for the npu device.
See commit 902bdc57451c ("powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn").

We don't need to take a reference on the device when assigning the PE as the struct pnv_ioda_pe is cleaned up at the same time as the (physical) device is released. Doing so prevents the device from being released, which is a problem for opencapi devices, since we want to be able to remove them through PCI hotplug.

Now the ugly part: nvlink npu devices are not meant to be released. Because of the above, we've always leaked a reference and simply removing it now is dangerous and would likely require more work. There's currently no release device callback for nvlink devices for example. So to be safe, this patch leaks a reference on the npu device, but only for nvlink and not opencapi.

---
 arch/powerpc/platforms/powernv/pci-ioda.c | 19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)
arch/powerpc/platforms/powernv/pci-ioda.c +12 -7
index ecd211c5f24a5..19cd6affdd5fb 100644
@@ -1071,14 +1071,13 @@ static struct pnv_ioda_pe *pnv_ioda_setup_dev_PE(struct pci_dev *dev)
 		return NULL;
 	}
 
-	/* NOTE: We get only one ref to the pci_dev for the pdn, not for the
-	 * pointer in the PE data structure, both should be destroyed at the
-	 * same time. However, this needs to be looked at more closely again
-	 * once we actually start removing things (Hotplug, SR-IOV, ...)
+	/* NOTE: We don't get a reference for the pointer in the PE
+	 * data structure, both the device and PE structures should be
+	 * destroyed at the same time. However, removing nvlink
+	 * devices will need some work.
 	 *
 	 * At some point we want to remove the PDN completely anyways
 	 */
-	pci_dev_get(dev);
 	pdn->pe_number = pe->pe_number;
 	pe->flags = PNV_IODA_PE_DEV;
 	pe->pdev = dev;
@@ -1093,7 +1092,6 @@ static struct pnv_ioda_pe *pnv_ioda_setup_dev_PE(struct pci_dev *dev)
 		pnv_ioda_free_pe(pe);
 		pdn->pe_number = IODA_INVALID_PE;
 		pe->pdev = NULL;
-		pci_dev_put(dev);
 		return NULL;
 	}
 
@@ -1213,6 +1211,14 @@ static struct pnv_ioda_pe *pnv_ioda_setup_npu_PE(struct pci_dev *npu_pdev)
 	struct pci_controller *hose = pci_bus_to_host(npu_pdev->bus);
 	struct pnv_phb *phb = hose->private_data;
 
+	/*
+	 * Intentionally leak a reference on the npu device (for
+	 * nvlink only; this is not an opencapi path) to make sure it
+	 * never goes away, as it's been the case all along and some
+	 * work is needed otherwise.
+	 */
+	pci_dev_get(npu_pdev);
+
 	/*
 	 * Due to a hardware errata PE#0 on the NPU is reserved for
 	 * error handling. This means we only have three PEs remaining
@@ -1236,7 +1242,6 @@ static struct pnv_ioda_pe *pnv_ioda_setup_npu_PE(struct pci_dev *npu_pdev)
 			 */
 			dev_info(&npu_pdev->dev,
 				"Associating to existing PE %x\n", pe_num);
-			pci_dev_get(npu_pdev);
 			npu_pdn = pci_get_pdn(npu_pdev);
 			rid = npu_pdev->bus->number << 8 | npu_pdn->devfn;
 			npu_pdn->pe_number = pe_num;
Signature · 1 line
2.25.1
author maintainer
#207 lore raw

PATCH 205/206 net: openvswitch: use div_u64() for 64-by-32 divisions

In reply to Sasha Levin

From: Tonghao Zhang <[email protected]>

[ Upstream commit 659d4587fe7233bfdff303744b20d6f41ad04362 ]

Compile the kernel for arm 32 platform, the build warning found. To fix that, should use div_u64() for divisions.
| net/openvswitch/meter.c:396: undefined reference to `__udivdi3'

[add more commit msg, change reported tag, and use div_u64 instead of do_div by Tonghao]

Fixes e57358873bb5d6ca ("net: openvswitch: use u64 for meter bucket")
---
 net/openvswitch/meter.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/openvswitch/meter.c +1 -1
index 6f5131d1074b0..5ea2471ffc03f 100644
@@ -256,7 +256,7 @@ static struct dp_meter *dp_meter_create(struct nlattr **a)
 		 * Start with a full bucket.
 		 */
 		band->bucket = (band->burst_size + band->rate) * 1000ULL;
-		band_max_delta_t = band->bucket / band->rate;
+		band_max_delta_t = div_u64(band->bucket, band->rate);
 		if (band_max_delta_t > meter->max_delta_t)
 			meter->max_delta_t = band_max_delta_t;
 		band++;
Signature · 1 line
2.25.1
author maintainer
#204 lore raw

PATCH 202/206 btrfs: qgroup: fix data leak caused by race between writeback and truncate

In reply to Sasha Levin

From: Qu Wenruo <[email protected]>

[ Upstream commit fa91e4aa1716004ea8096d5185ec0451e206aea0 ]

[BUG]
When running tests like generic/013 on test device with btrfs quota enabled, it can normally lead to data leak, detected at unmount time:

BTRFS warning (device dm-3): qgroup 0/5 has unreleased space, type 0 rsv 4096

  ------------[ cut here ]------------
  WARNING: CPU: 11 PID: 16386 at fs/btrfs/disk-io.c:4142 close_ctree+0x1dc/0x323 [btrfs]
  RIP: 0010:close_ctree+0x1dc/0x323 [btrfs]
  Call Trace:
   btrfs_put_super+0x15/0x17 [btrfs]
   generic_shutdown_super+0x72/0x110
   kill_anon_super+0x18/0x30
   btrfs_kill_super+0x17/0x30 [btrfs]
   deactivate_locked_super+0x3b/0xa0
   deactivate_super+0x40/0x50
   cleanup_mnt+0x135/0x190
   __cleanup_mnt+0x12/0x20
   task_work_run+0x64/0xb0
   __prepare_exit_to_usermode+0x1bc/0x1c0
   __syscall_return_slowpath+0x47/0x230
   do_syscall_64+0x64/0xb0
   entry_SYSCALL_64_after_hwframe+0x44/0xa9
  ---[ end trace caf08beafeca2392 ]---
  BTRFS error (device dm-3): qgroup reserved space leaked

[CAUSE]
In the offending case, the offending operations are:
2/6: writev f2X[269 1 0 0 0 0] [1006997,67,288] 0 2/7: truncate f2X[269 1 0 0 48 1026293] 18388 0

The following sequence of events could happen after the writev():

	CPU1 (writeback)		|		CPU2 (truncate)
-----------------------------------------------------------------
btrfs_writepages()			|
|- extent_write_cache_pages()		|
   |- Got page for 1003520		|
   |  1003520 is Dirty, no writeback	|
   |  So (!clear_page_dirty_for_io())   |
   |  gets called for it		|
   |- Now page 1003520 is Clean.	|
   |					| btrfs_setattr()
   |					| |- btrfs_setsize()
   |					|    |- truncate_setsize()
   |					|       New i_size is 18388
   |- __extent_writepage()		|
   |  |- page_offset() > i_size		|
      |- btrfs_invalidatepage()		|
	 |- Page is clean, so no qgroup |

callback executed

This means, the qgroup reserved data space is not properly released in btrfs_invalidatepage() as the page is Clean.

[FIX]
Instead of checking the dirty bit of a page, call btrfs_qgroup_free_data() unconditionally in btrfs_invalidatepage().

As qgroup rsv are completely bound to the QGROUP_RESERVED bit of io_tree, not bound to page status, thus we won't cause double freeing anyway.

Fixes 0b34c261e235 ("btrfs: qgroup: Prevent qgroup->reserved from going subzero")
---
 fs/btrfs/inode.c | 23 ++++++++++-------------
 1 file changed, 10 insertions(+), 13 deletions(-)
fs/btrfs/inode.c +10 -13
index bdfe159a60da6..64d459ca76d06 100644
@@ -8913,20 +8913,17 @@ again:
 	/*
 	 * Qgroup reserved space handler
 	 * Page here will be either
-	 * 1) Already written to disk
-	 *    In this case, its reserved space is released from data rsv map
-	 *    and will be freed by delayed_ref handler finally.
-	 *    So even we call qgroup_free_data(), it won't decrease reserved
-	 *    space.
-	 * 2) Not written to disk
-	 *    This means the reserved space should be freed here. However,
-	 *    if a truncate invalidates the page (by clearing PageDirty)
-	 *    and the page is accounted for while allocating extent
-	 *    in btrfs_check_data_free_space() we let delayed_ref to
-	 *    free the entire extent.
+	 * 1) Already written to disk or ordered extent already submitted
+	 *    Then its QGROUP_RESERVED bit in io_tree is already cleaned.
+	 *    Qgroup will be handled by its qgroup_record then.
+	 *    btrfs_qgroup_free_data() call will do nothing here.
+	 *
+	 * 2) Not written to disk yet
+	 *    Then btrfs_qgroup_free_data() call will clear the QGROUP_RESERVED
+	 *    bit of its io_tree, and free the qgroup reserved data space.
+	 *    Since the IO will never happen for this page.
 	 */
-	if (PageDirty(page))
-		btrfs_qgroup_free_data(inode, NULL, page_start, PAGE_SIZE);
+	btrfs_qgroup_free_data(inode, NULL, page_start, PAGE_SIZE);
 	if (!inode_evicting) {
 		clear_extent_bit(tree, page_start, page_end,
 				 EXTENT_LOCKED | EXTENT_DIRTY |
Signature · 1 line
2.25.1
author maintainer
#203 lore raw

PATCH 201/206 vfio/pci: fix racy on error and request eventfd ctx

In reply to Sasha Levin

From: Zeng Tao <[email protected]>

[ Upstream commit b872d0640840018669032b20b6375a478ed1f923 ]

The vfio_pci_release call will free and clear the error and request eventfd ctx while these ctx could be in use at the same time in the function like vfio_pci_request, and it's expected to protect them under the vdev->igate mutex, which is missing in vfio_pci_release.

This issue is introduced since commit 1518ac272e78 ("vfio/pci: fix memory leaks of eventfd ctx"),and since commit 5c5866c593bb ("vfio/pci: Clear error and request eventfd ctx after releasing"), it's very easily to trigger the kernel panic like this:

[ 9513.904346] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
[ 9513.913091] Mem abort info:
[ 9513.915871]   ESR = 0x96000006
[ 9513.918912]   EC = 0x25: DABT (current EL), IL = 32 bits
[ 9513.924198]   SET = 0, FnV = 0
[ 9513.927238]   EA = 0, S1PTW = 0
[ 9513.930364] Data abort info:
[ 9513.933231]   ISV = 0, ISS = 0x00000006
[ 9513.937048]   CM = 0, WnR = 0
[ 9513.940003] user pgtable: 4k pages, 48-bit VAs, pgdp=0000007ec7d12000
[ 9513.946414] [0000000000000008] pgd=0000007ec7d13003, p4d=0000007ec7d13003, pud=0000007ec728c003, pmd=0000000000000000
[ 9513.956975] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[ 9513.962521] Modules linked in: vfio_pci vfio_virqfd vfio_iommu_type1 vfio hclge hns3 hnae3 [last unloaded: vfio_pci]
[ 9513.972998] CPU: 4 PID: 1327 Comm: bash Tainted: G        W         5.8.0-rc4+ #3
[ 9513.980443] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B270.01 05/08/2020
[ 9513.989274] pstate: 80400089 (Nzcv daIf +PAN -UAO BTYPE=--)
[ 9513.994827] pc : _raw_spin_lock_irqsave+0x48/0x88
[ 9513.999515] lr : eventfd_signal+0x6c/0x1b0
[ 9514.003591] sp : ffff800038a0b960
[ 9514.006889] x29: ffff800038a0b960 x28: ffff007ef7f4da10
[ 9514.012175] x27: ffff207eefbbfc80 x26: ffffbb7903457000
[ 9514.017462] x25: ffffbb7912191000 x24: ffff007ef7f4d400
[ 9514.022747] x23: ffff20be6e0e4c00 x22: 0000000000000008
[ 9514.028033] x21: 0000000000000000 x20: 0000000000000000
[ 9514.033321] x19: 0000000000000008 x18: 0000000000000000
[ 9514.038606] x17: 0000000000000000 x16: ffffbb7910029328
[ 9514.043893] x15: 0000000000000000 x14: 0000000000000001
[ 9514.049179] x13: 0000000000000000 x12: 0000000000000002
[ 9514.054466] x11: 0000000000000000 x10: 0000000000000a00
[ 9514.059752] x9 : ffff800038a0b840 x8 : ffff007ef7f4de60
[ 9514.065038] x7 : ffff007fffc96690 x6 : fffffe01faffb748
[ 9514.070324] x5 : 0000000000000000 x4 : 0000000000000000
[ 9514.075609] x3 : 0000000000000000 x2 : 0000000000000001
[ 9514.080895] x1 : ffff007ef7f4d400 x0 : 0000000000000000
[ 9514.086181] Call trace:
[ 9514.088618]  _raw_spin_lock_irqsave+0x48/0x88
[ 9514.092954]  eventfd_signal+0x6c/0x1b0
[ 9514.096691]  vfio_pci_request+0x84/0xd0 [vfio_pci]
[ 9514.101464]  vfio_del_group_dev+0x150/0x290 [vfio]
[ 9514.106234]  vfio_pci_remove+0x30/0x128 [vfio_pci]
[ 9514.111007]  pci_device_remove+0x48/0x108
[ 9514.115001]  device_release_driver_internal+0x100/0x1b8
[ 9514.120200]  device_release_driver+0x28/0x38
[ 9514.124452]  pci_stop_bus_device+0x68/0xa8
[ 9514.128528]  pci_stop_and_remove_bus_device+0x20/0x38
[ 9514.133557]  pci_iov_remove_virtfn+0xb4/0x128
[ 9514.137893]  sriov_disable+0x3c/0x108
[ 9514.141538]  pci_disable_sriov+0x28/0x38
[ 9514.145445]  hns3_pci_sriov_configure+0x48/0xb8 [hns3]
[ 9514.150558]  sriov_numvfs_store+0x110/0x198
[ 9514.154724]  dev_attr_store+0x44/0x60
[ 9514.158373]  sysfs_kf_write+0x5c/0x78
[ 9514.162018]  kernfs_fop_write+0x104/0x210
[ 9514.166010]  __vfs_write+0x48/0x90
[ 9514.169395]  vfs_write+0xbc/0x1c0
[ 9514.172694]  ksys_write+0x74/0x100
[ 9514.176079]  __arm64_sys_write+0x24/0x30
[ 9514.179987]  el0_svc_common.constprop.4+0x110/0x200
[ 9514.184842]  do_el0_svc+0x34/0x98
[ 9514.188144]  el0_svc+0x14/0x40
[ 9514.191185]  el0_sync_handler+0xb0/0x2d0
[ 9514.195088]  el0_sync+0x140/0x180
[ 9514.198389] Code: b9001020 d2800000 52800022 f9800271 (885ffe61)
[ 9514.204455] ---[ end trace 648de00c8406465f ]---
[ 9514.212308] note: bash[1327] exited with preempt_count 1
Cc Qian Cai <[email protected]>
Cc Alex Williamson <[email protected]>
Fixes 1518ac272e78 ("vfio/pci: fix memory leaks of eventfd ctx")
---
 drivers/vfio/pci/vfio_pci.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/vfio/pci/vfio_pci.c +5 -0
index 94fad366312f1..58e7336b2748b 100644
@@ -409,14 +409,19 @@ static void vfio_pci_release(void *device_data)
 	if (!(--vdev->refcnt)) {
 		vfio_spapr_pci_eeh_release(vdev->pdev);
 		vfio_pci_disable(vdev);
+		mutex_lock(&vdev->igate);
 		if (vdev->err_trigger) {
 			eventfd_ctx_put(vdev->err_trigger);
 			vdev->err_trigger = NULL;
 		}
+		mutex_unlock(&vdev->igate);
+
+		mutex_lock(&vdev->igate);
 		if (vdev->req_trigger) {
 			eventfd_ctx_put(vdev->req_trigger);
 			vdev->req_trigger = NULL;
 		}
+		mutex_unlock(&vdev->igate);
 	}
 
 	mutex_unlock(&driver_lock);
Signature · 1 line
2.25.1
author maintainer
#202 lore raw

PATCH 200/206 selftests/x86/syscall_nt: Clear weird flags after each test

In reply to Sasha Levin

From: Andy Lutomirski <[email protected]>

[ Upstream commit a61fa2799ef9bf6c4f54cf7295036577cececc72 ]

Clear the weird flags before logging to improve strace output -- logging results while, say, TF is set does no one any favors.

---
 tools/testing/selftests/x86/syscall_nt.c | 1 +
 1 file changed, 1 insertion(+)
tools/testing/selftests/x86/syscall_nt.c +1 -0
index 43fcab367fb0a..74e6b3fc2d09e 100644
@@ -67,6 +67,7 @@ static void do_it(unsigned long extraflags)
 	set_eflags(get_eflags() | extraflags);
 	syscall(SYS_getpid);
 	flags = get_eflags();
+	set_eflags(X86_EFLAGS_IF | X86_EFLAGS_FIXED);
 	if ((flags & extraflags) == extraflags) {
 		printf("[OK]\tThe syscall worked and flags are still set\n");
 	} else {
Signature · 1 line
2.25.1
author maintainer
#196 lore raw

PATCH 194/206 x86/speculation/mds: Mark mds_user_clear_cpu_buffers() __always_inline

In reply to Sasha Levin

From: Thomas Gleixner <[email protected]>

[ Upstream commit a7ef9ba986b5fae9d80f8a7b31db0423687efe4e ]

Prevent the compiler from uninlining and creating traceable/probable functions as this is invoked _after_ context tracking switched to CONTEXT_USER and rcu idle.

---
 arch/x86/include/asm/nospec-branch.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/x86/include/asm/nospec-branch.h +2 -2
index e3f70c60e8ccd..62f9903544b59 100644
@@ -330,7 +330,7 @@ DECLARE_STATIC_KEY_FALSE(mds_idle_clear);
  * combination with microcode which triggers a CPU buffer flush when the
  * instruction is executed.
  */
-static inline void mds_clear_cpu_buffers(void)
+static __always_inline void mds_clear_cpu_buffers(void)
 {
 	static const u16 ds = __KERNEL_DS;
 
@@ -351,7 +351,7 @@ static inline void mds_clear_cpu_buffers(void)
  *
  * Clear CPU buffers if the corresponding static key is enabled
  */
-static inline void mds_user_clear_cpu_buffers(void)
+static __always_inline void mds_user_clear_cpu_buffers(void)
 {
 	if (static_branch_likely(&mds_user_clear))
 		mds_clear_cpu_buffers();
Signature · 1 line
2.25.1
author maintainer
#201 lore raw

PATCH 199/206 scsi: libfc: Skip additional kref updating work event

In reply to Sasha Levin

From: Javed Hasan <[email protected]>

[ Upstream commit 823a65409c8990f64c5693af98ce0e7819975cba ]

When an rport event (RPORT_EV_READY) is updated without work being queued, avoid taking an additional reference.

This issue was leading to memory leak. Trace from KMEMLEAK tool:

unreferenced object 0xffff8888259e8780 (size 512):
comm "kworker/2:1", jiffies 4433237386 (age 113021.971s)

    hex dump (first 32 bytes):
	58 0a ec cf 83 88 ff ff 00 00 00 00 00 00 00 00
	01 00 00 00 08 00 00 00 13 7d f0 1e 0e 00 00 10
  backtrace:
  [<000000006b25760f>] fc_rport_recv_req+0x3c6/0x18f0 [libfc]
  [<00000000f208d994>] fc_lport_recv_els_req+0x120/0x8a0 [libfc]
  [<00000000a9c437b8>] fc_lport_recv+0xb9/0x130 [libfc]
  [<00000000a9c437b8>] fc_lport_recv+0xb9/0x130 [libfc]
  [<00000000ad5be37b>] qedf_ll2_process_skb+0x73d/0xad0 [qedf]
  [<00000000e0eb6893>] process_one_work+0x382/0x6c0
  [<000000002dfd9e21>] worker_thread+0x57/0x5c0
  [<00000000b648204f>] kthread+0x1a0/0x1c0
  [<0000000072f5ab20>] ret_from_fork+0x35/0x40
  [<000000001d5c05d8>] 0xffffffffffffffff

Below is the log sequence which leads to memory leak. Here we get the RPORT_EV_READY and RPORT_EV_STOP back to back, which lead to overwrite the event RPORT_EV_READY by event RPORT_EV_STOP. Because of this, kref_count gets incremented by 1.

kernel: host0: rport fffce5: Received PLOGI request
kernel: host0: rport fffce5: Received PLOGI in INIT state
kernel: host0: rport fffce5: Port is Ready
kernel: host0: rport fffce5: Received PRLI request while in state Ready
kernel: host0: rport fffce5: PRLI rspp type 8 active 1 passive 0
kernel: host0: rport fffce5: Received LOGO request while in state Ready
kernel: host0: rport fffce5: Delete port
kernel: host0: rport fffce5: Received PLOGI request
kernel: host0: rport fffce5: Received PLOGI in state Delete - send busy
kernel: host0: rport fffce5: work event 3
kernel: host0: rport fffce5: lld callback ev 3
kernel: host0: rport fffce5: work delete

---
 drivers/scsi/libfc/fc_rport.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/scsi/libfc/fc_rport.c +5 -4
index f39d2d62b002f..2b3239765c249 100644
@@ -495,10 +495,11 @@ static void fc_rport_enter_delete(struct fc_rport_priv *rdata,
 
 	fc_rport_state_enter(rdata, RPORT_ST_DELETE);
 
-	kref_get(&rdata->kref);
-	if (rdata->event == RPORT_EV_NONE &&
-	    !queue_work(rport_event_queue, &rdata->event_work))
-		kref_put(&rdata->kref, fc_rport_destroy);
+	if (rdata->event == RPORT_EV_NONE) {
+		kref_get(&rdata->kref);
+		if (!queue_work(rport_event_queue, &rdata->event_work))
+			kref_put(&rdata->kref, fc_rport_destroy);
+	}
 
 	rdata->event = event;
 }
Signature · 1 line
2.25.1
author maintainer
#194 lore raw

PATCH 192/206 rapidio: avoid data race between file operation callbacks and mport_cdev_add().

In reply to Sasha Levin

From: Madhuparna Bhowmik <[email protected]>

[ Upstream commit e1c3cdb26ab881b77486dc50370356a349077c74 ]

Fields of md(mport_dev) are set after cdev_device_add(). However, the file operation callbacks can be called after cdev_device_add() and therefore accesses to fields of md in the callbacks can race with the rest of the mport_cdev_add() function.

One such example is INIT_LIST_HEAD(&md->portwrites) in mport_cdev_add(), the list is initialised after cdev_device_add(). This can race with list_add_tail(&pw_filter->md_node,&md->portwrites) in rio_mport_add_pw_filter() which is called by unlocked_ioctl.

To avoid such data races use cdev_device_add() after initializing md.

Found by Linux Driver Verification project (linuxtesting.org).

---
 drivers/rapidio/devices/rio_mport_cdev.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)
drivers/rapidio/devices/rio_mport_cdev.c +7 -7
index 5940780648e0f..f36a8a5261a13 100644
@@ -2385,13 +2385,6 @@ static struct mport_dev *mport_cdev_add(struct rio_mport *mport)
 	cdev_init(&md->cdev, &mport_fops);
 	md->cdev.owner = THIS_MODULE;
 
-	ret = cdev_device_add(&md->cdev, &md->dev);
-	if (ret) {
-		rmcd_error("Failed to register mport %d (err=%d)",
-		       mport->id, ret);
-		goto err_cdev;
-	}
-
 	INIT_LIST_HEAD(&md->doorbells);
 	spin_lock_init(&md->db_lock);
 	INIT_LIST_HEAD(&md->portwrites);
@@ -2411,6 +2404,13 @@ static struct mport_dev *mport_cdev_add(struct rio_mport *mport)
 #else
 	md->properties.transfer_mode |= RIO_TRANSFER_MODE_TRANSFER;
 #endif
+
+	ret = cdev_device_add(&md->cdev, &md->dev);
+	if (ret) {
+		rmcd_error("Failed to register mport %d (err=%d)",
+		       mport->id, ret);
+		goto err_cdev;
+	}
 	ret = rio_query_mport(mport, &attr);
 	if (!ret) {
 		md->properties.flags = attr.flags;
Signature · 1 line
2.25.1
author maintainer
#192 lore raw

PATCH 190/206 ceph: fix potential race in ceph_check_caps

In reply to Sasha Levin

From: Jeff Layton <[email protected]>

[ Upstream commit dc3da0461cc4b76f2d0c5b12247fcb3b520edbbf ]

Nothing ensures that session will still be valid by the time we dereference the pointer. Take and put a reference.

In principle, we should always be able to get a reference here, but throw a warning if that's ever not the case.

---
 fs/ceph/caps.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)
fs/ceph/caps.c +13 -1
index a2d4eed27f804..c0dbf8b7762b4 100644
@@ -2015,12 +2015,24 @@ ack:
 			if (mutex_trylock(&session->s_mutex) == 0) {
 				dout("inverting session/ino locks on %p\n",
 				     session);
+				session = ceph_get_mds_session(session);
 				spin_unlock(&ci->i_ceph_lock);
 				if (took_snap_rwsem) {
 					up_read(&mdsc->snap_rwsem);
 					took_snap_rwsem = 0;
 				}
-				mutex_lock(&session->s_mutex);
+				if (session) {
+					mutex_lock(&session->s_mutex);
+					ceph_put_mds_session(session);
+				} else {
+					/*
+					 * Because we take the reference while
+					 * holding the i_ceph_lock, it should
+					 * never be NULL. Throw a warning if it
+					 * ever is.
+					 */
+					WARN_ON_ONCE(true);
+				}
 				goto retry;
 			}
 		}
Signature · 1 line
2.25.1
author maintainer
#191 lore raw

PATCH 189/206 PCI: tegra: Fix runtime PM imbalance on error

In reply to Sasha Levin

From: Dinghao Liu <[email protected]>

[ Upstream commit fcee90cdf6f3a3a371add04d41528d5ba9c3b411 ]

pm_runtime_get_sync() increments the runtime PM usage counter even when it returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced.

Also, call pm_runtime_disable() when pm_runtime_get_sync() returns an error code.

---
 drivers/pci/controller/pci-tegra.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/pci/controller/pci-tegra.c +1 -2
index 6f86583605a46..097c02197ec8f 100644
@@ -2400,7 +2400,7 @@ static int tegra_pcie_probe(struct platform_device *pdev)
 	err = pm_runtime_get_sync(pcie->dev);
 	if (err < 0) {
 		dev_err(dev, "fail to enable pcie controller: %d\n", err);
-		goto teardown_msi;
+		goto pm_runtime_put;
 	}
 
 	err = tegra_pcie_request_resources(pcie);
@@ -2440,7 +2440,6 @@ free_resources:
 pm_runtime_put:
 	pm_runtime_put_sync(pcie->dev);
 	pm_runtime_disable(pcie->dev);
-teardown_msi:
 	tegra_pcie_msi_teardown(pcie);
 put_resources:
 	tegra_pcie_put_resources(pcie);
Signature · 1 line
2.25.1
author maintainer
#186 lore raw

PATCH 184/206 perf kcore_copy: Fix module map when there are no modules loaded

In reply to Sasha Levin

From: Adrian Hunter <[email protected]>

[ Upstream commit 61f82e3fb697a8e85f22fdec786528af73dc36d1 ]

In the absence of any modules, no "modules" map is created, but there are other executable pages to map, due to eBPF JIT, kprobe or ftrace. Map them by recognizing that the first "module" symbol is not necessarily from a module, and adjust the map accordingly.

Cc Alexander Shishkin <[email protected]>
Cc Borislav Petkov <[email protected]>
Cc H. Peter Anvin <[email protected]>
Cc Jiri Olsa <[email protected]>
Cc Leo Yan <[email protected]>
Cc Mark Rutland <[email protected]>
Cc Masami Hiramatsu <[email protected]>
Cc Mathieu Poirier <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Steven Rostedt (VMware) <[email protected]>
---
 tools/perf/util/symbol-elf.c | 7 +++++++
 1 file changed, 7 insertions(+)
tools/perf/util/symbol-elf.c +7 -0
index a701a8a48f005..166c621e02235 100644
@@ -1421,6 +1421,7 @@ struct kcore_copy_info {
 	u64 first_symbol;
 	u64 last_symbol;
 	u64 first_module;
+	u64 first_module_symbol;
 	u64 last_module_symbol;
 	size_t phnum;
 	struct list_head phdrs;
@@ -1497,6 +1498,8 @@ static int kcore_copy__process_kallsyms(void *arg, const char *name, char type,
 		return 0;
 
 	if (strchr(name, '[')) {
+		if (!kci->first_module_symbol || start < kci->first_module_symbol)
+			kci->first_module_symbol = start;
 		if (start > kci->last_module_symbol)
 			kci->last_module_symbol = start;
 		return 0;
@@ -1694,6 +1697,10 @@ static int kcore_copy__calc_maps(struct kcore_copy_info *kci, const char *dir,
 		kci->etext += page_size;
 	}
 
+	if (kci->first_module_symbol &&
+	    (!kci->first_module || kci->first_module_symbol < kci->first_module))
+		kci->first_module = kci->first_module_symbol;
+
 	kci->first_module = round_down(kci->first_module, page_size);
 
 	if (kci->last_module_symbol) {
Signature · 1 line
2.25.1
author maintainer
#185 lore raw

PATCH 183/206 perf metricgroup: Free metric_events on error

In reply to Sasha Levin

From: Ian Rogers <[email protected]>

[ Upstream commit a159e2fe89b4d1f9fb54b0ae418b961e239bf617 ]

Avoid a simple memory leak.

Cc Alexander Shishkin <[email protected]>
Cc Alexei Starovoitov <[email protected]>
Cc Andi Kleen <[email protected]>
Cc Andrii Nakryiko <[email protected]>
Cc Cong Wang <[email protected]>
Cc Daniel Borkmann <[email protected]>
Cc Jin Yao <[email protected]>
Cc Jiri Olsa <[email protected]>
Cc John Fastabend <[email protected]>
Cc John Garry <[email protected]>
Cc Kajol Jain <[email protected]>
Cc Kan Liang <[email protected]>
Cc Kim Phillips <[email protected]>
Cc Mark Rutland <[email protected]>
Cc Martin KaFai Lau <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Song Liu <[email protected]>
Cc Stephane Eranian <[email protected]>
Cc Vince Weaver <[email protected]>
Cc Yonghong Song <[email protected]>
Cc kp singh <[email protected]>
---
 tools/perf/util/metricgroup.c | 3 +++
 1 file changed, 3 insertions(+)
tools/perf/util/metricgroup.c +3 -0
index 8b3dafe3fac3a..6dcc6e1182a54 100644
@@ -171,6 +171,7 @@ static int metricgroup__setup_events(struct list_head *groups,
 		if (!evsel) {
 			pr_debug("Cannot resolve %s: %s\n",
 					eg->metric_name, eg->metric_expr);
+			free(metric_events);
 			continue;
 		}
 		for (i = 0; i < eg->idnum; i++)
@@ -178,11 +179,13 @@ static int metricgroup__setup_events(struct list_head *groups,
 		me = metricgroup__lookup(metric_events_list, evsel, true);
 		if (!me) {
 			ret = -ENOMEM;
+			free(metric_events);
 			break;
 		}
 		expr = malloc(sizeof(struct metric_expr));
 		if (!expr) {
 			ret = -ENOMEM;
+			free(metric_events);
 			break;
 		}
 		expr->metric_expr = eg->metric_expr;
Signature · 1 line
2.25.1
author maintainer
#184 lore raw

PATCH 182/206 perf util: Fix memory leak of prefix_if_not_in

In reply to Sasha Levin

From: Xie XiuQi <[email protected]>

[ Upstream commit 07e9a6f538cbeecaf5c55b6f2991416f873cdcbd ]

Need to free "str" before return when asprintf() failed to avoid memory leak.

---
 tools/perf/util/sort.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/perf/util/sort.c +1 -1
index 46daa22b86e3b..85ff4f68adc00 100644
@@ -2690,7 +2690,7 @@ static char *prefix_if_not_in(const char *pre, char *str)
 		return str;
 
 	if (asprintf(&n, "%s,%s", pre, str) < 0)
-		return NULL;
+		n = NULL;
 
 	free(str);
 	return n;
Signature · 1 line
2.25.1
author maintainer
#182 lore raw

PATCH 180/206 perf trace: Fix the selection for architectures to generate the errno name tables

In reply to Sasha Levin

From: Ian Rogers <[email protected]>

[ Upstream commit 7597ce89b3ed239f7a3408b930d2a6c7a4c938a1 ]

Make the architecture test directory agree with the code comment.

Committer notes:

This was split from a larger patch.

The code was assuming the developer always worked from tools/perf/, so make sure we do the test -d having $toolsdir/perf/arch/$arch, to match the intent expressed in the comment, just above that loop.

Cc Adrian Hunter <[email protected]>
Cc Alexander Shishkin <[email protected]>
Cc Alexios Zavras <[email protected]>
Cc Andi Kleen <[email protected]>
Cc Greg Kroah-Hartman <[email protected]>
Cc Igor Lubashev <[email protected]>
Cc Jiri Olsa <[email protected]>
Cc Kan Liang <[email protected]>
Cc Mark Rutland <[email protected]>
Cc Mathieu Poirier <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Nick Desaulniers <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Stephane Eranian <[email protected]>
Cc Thomas Gleixner <[email protected]>
Cc Wei Li <[email protected]>
---
 tools/perf/trace/beauty/arch_errno_names.sh | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/perf/trace/beauty/arch_errno_names.sh +1 -1
index 22c9fc900c847..f8c44a85650be 100755
@@ -91,7 +91,7 @@ EoHEADER
 # in tools/perf/arch
 archlist=""
 for arch in $(find $toolsdir/arch -maxdepth 1 -mindepth 1 -type d -printf "%f\n" | grep -v x86 | sort); do
-	test -d arch/$arch && archlist="$archlist $arch"
+	test -d $toolsdir/perf/arch/$arch && archlist="$archlist $arch"
 done
 
 for arch in x86 $archlist generic; do
Signature · 1 line
2.25.1
author maintainer
#183 lore raw

PATCH 181/206 perf stat: Fix duration_time value for higher intervals

In reply to Sasha Levin

From: Jiri Olsa <[email protected]>

[ Upstream commit ea9eb1f456a08c18feb485894185f7a4e31cc8a4 ]

Joakim reported wrong duration_time value for interval bigger than 4000 [1].

The problem is in the interval value we pass to update_stats function, which is typed as 'unsigned int' and overflows when we get over 2^32 (happens between intervals 4000 and 5000).

Retyping the passed value to unsigned long long.

[1] https://www.spinics.net/lists/linux-perf-users/msg11777.html

Fixes b90f1333ef08 ("perf stat: Update walltime_nsecs_stats in interval mode")
Cc Alexander Shishkin <[email protected]>
Cc Andi Kleen <[email protected]>
Cc Michael Petlan <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Peter Zijlstra <[email protected]>
---
 tools/perf/builtin-stat.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/perf/builtin-stat.c +1 -1
index 6aae10ff954c7..adabe9d4dc866 100644
@@ -422,7 +422,7 @@ static void process_interval(void)
 	}
 
 	init_stats(&walltime_nsecs_stats);
-	update_stats(&walltime_nsecs_stats, stat_config.interval * 1000000);
+	update_stats(&walltime_nsecs_stats, stat_config.interval * 1000000ULL);
 	print_counters(&rs, 0, NULL);
 }
 
Signature · 1 line
2.25.1
author maintainer
#177 lore raw

PATCH 175/206 usb: dwc3: Increase timeout for CmdAct cleared by device controller

In reply to Sasha Levin

From: Yu Chen <[email protected]>

[ Upstream commit 1c0e69ae1b9f9004fd72978612ae3463791edc56 ]

If the SS PHY is in P3, there is no pipe_clk, HW may use suspend_clk for function, as suspend_clk is slow so EP command need more time to complete, e.g, imx8M suspend_clk is 32K, set ep configuration will take about 380us per below trace time stamp(44.286278 - 44.285897 = 0.000381):

configfs_acm.sh-822 [000] d..1 44.285896: dwc3_writel: addr
000000006d59aae1 value 00000401
configfs_acm.sh-822 [000] d..1 44.285897: dwc3_readl: addr
000000006d59aae1 value 00000401
... ...
configfs_acm.sh-822 [000] d..1 44.286278: dwc3_readl: addr
000000006d59aae1 value 00000001
configfs_acm.sh-822 [000] d..1 44.286279: dwc3_gadget_ep_cmd:
ep0out: cmd 'Set Endpoint Configuration' [401] params 00001000 00000500 00000000 --> status: Successful

This was originally found on Hisilicon Kirin Soc that need more time for the device controller to clear the CmdAct of DEPCMD.

---
 drivers/usb/dwc3/gadget.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/dwc3/gadget.c +1 -1
index 7bf2573dd459e..37cc3fd7c3cad 100644
@@ -270,7 +270,7 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned cmd,
 {
 	const struct usb_endpoint_descriptor *desc = dep->endpoint.desc;
 	struct dwc3		*dwc = dep->dwc;
-	u32			timeout = 1000;
+	u32			timeout = 5000;
 	u32			saved_config = 0;
 	u32			reg;
 
Signature · 1 line
2.25.1
author maintainer
#181 lore raw

PATCH 179/206 perf evsel: Fix 2 memory leaks

In reply to Sasha Levin

From: Ian Rogers <[email protected]>

[ Upstream commit 3efc899d9afb3d03604f191a0be9669eabbfc4aa ]

If allocated, perf_pkg_mask and metric_events need freeing.

---
 tools/perf/util/evsel.c | 2 ++
 1 file changed, 2 insertions(+)
tools/perf/util/evsel.c +2 -0
index e8586957562b3..1b7b6244c8cfe 100644
@@ -1291,6 +1291,8 @@ void perf_evsel__exit(struct perf_evsel *evsel)
 	zfree(&evsel->group_name);
 	zfree(&evsel->name);
 	zfree(&evsel->pmu_name);
+	zfree(&evsel->per_pkg_mask);
+	zfree(&evsel->metric_events);
 	perf_evsel__object.fini(evsel);
 }
 
Signature · 1 line
2.25.1
author maintainer
#176 lore raw

PATCH 174/206 printk: handle blank console arguments passed in.

In reply to Sasha Levin

From: Shreyas Joshi <[email protected]>

[ Upstream commit 48021f98130880dd74286459a1ef48b5e9bc374f ]

If uboot passes a blank string to console_setup then it results in a trashed memory. Ultimately, the kernel crashes during freeing up the memory.

This fix checks if there is a blank parameter being passed to console_setup from uboot. In case it detects that the console parameter is blank then it doesn't setup the serial device and it gracefully exits.

---
 kernel/printk/printk.c | 3 +++
 1 file changed, 3 insertions(+)
kernel/printk/printk.c +3 -0
index 3cb0e5b479ff3..cf272aba362be 100644
@@ -2148,6 +2148,9 @@ static int __init console_setup(char *str)
 	char *s, *options, *brl_options = NULL;
 	int idx;
 
+	if (str[0] == 0)
+		return 1;
+
 	if (_braille_console_setup(&str, &brl_options))
 		return 1;
 
Signature · 1 line
2.25.1
author maintainer
#179 lore raw

PATCH 177/206 vfio/pci: fix memory leaks of eventfd ctx

In reply to Sasha Levin

From: Qian Cai <[email protected]>

[ Upstream commit 1518ac272e789cae8c555d69951b032a275b7602 ]

Finished a qemu-kvm (-device vfio-pci,host=0001:01:00.0) triggers a few memory leaks after a while because vfio_pci_set_ctx_trigger_single() calls eventfd_ctx_fdget() without the matching eventfd_ctx_put() later. Fix it by calling eventfd_ctx_put() for those memory in vfio_pci_release() before vfio_device_release().

unreferenced object 0xebff008981cc2b00 (size 128):
comm "qemu-kvm", pid 4043, jiffies 4294994816 (age 9796.310s) hex dump (first 32 bytes):
01 00 00 00 6b 6b 6b 6b 00 00 00 00 ad 4e ad de ....kkkk.....N.. ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
backtrace:

    [<00000000917e8f8d>] slab_post_alloc_hook+0x74/0x9c
    [<00000000df0f2aa2>] kmem_cache_alloc_trace+0x2b4/0x3d4
    [<000000005fcec025>] do_eventfd+0x54/0x1ac
    [<0000000082791a69>] __arm64_sys_eventfd2+0x34/0x44
    [<00000000b819758c>] do_el0_svc+0x128/0x1dc
    [<00000000b244e810>] el0_sync_handler+0xd0/0x268
    [<00000000d495ef94>] el0_sync+0x164/0x180

unreferenced object 0x29ff008981cc4180 (size 128):
comm "qemu-kvm", pid 4043, jiffies 4294994818 (age 9796.290s) hex dump (first 32 bytes):
01 00 00 00 6b 6b 6b 6b 00 00 00 00 ad 4e ad de ....kkkk.....N.. ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
backtrace:

    [<00000000917e8f8d>] slab_post_alloc_hook+0x74/0x9c
    [<00000000df0f2aa2>] kmem_cache_alloc_trace+0x2b4/0x3d4
    [<000000005fcec025>] do_eventfd+0x54/0x1ac
    [<0000000082791a69>] __arm64_sys_eventfd2+0x34/0x44
    [<00000000b819758c>] do_el0_svc+0x128/0x1dc
    [<00000000b244e810>] el0_sync_handler+0xd0/0x268
    [<00000000d495ef94>] el0_sync+0x164/0x180
---
 drivers/vfio/pci/vfio_pci.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/vfio/pci/vfio_pci.c +4 -0
index 9f72a6ee13b53..86cd8bdfa9f28 100644
@@ -409,6 +409,10 @@ static void vfio_pci_release(void *device_data)
 	if (!(--vdev->refcnt)) {
 		vfio_spapr_pci_eeh_release(vdev->pdev);
 		vfio_pci_disable(vdev);
+		if (vdev->err_trigger)
+			eventfd_ctx_put(vdev->err_trigger);
+		if (vdev->req_trigger)
+			eventfd_ctx_put(vdev->req_trigger);
 	}
 
 	mutex_unlock(&driver_lock);
Signature · 1 line
2.25.1
author maintainer
#180 lore raw

PATCH 178/206 perf parse-events: Fix incorrect conversion of 'if () free()' to 'zfree()'

In reply to Sasha Levin

From: Arnaldo Carvalho de Melo <[email protected]>

[ Upstream commit 7fcdccd4237724931d9773d1e3039bfe053a6f52 ]

When applying a patch by Ian I incorrectly converted to zfree() an expression that involved testing some other struct member, not the one being freed, which lead to bugs reproduceable by:

  $ perf stat -e i/bs,tsc,L2/o sleep 1
  WARNING: multiple event parsing errors
  Segmentation fault (core dumped)
  $

Fix it by restoring the test for pos->free_str before freeing pos->val.str, but continue using zfree(&pos->val.str) to set that member to NULL after freeing it.

Fixes e8dfb81838b1 ("perf parse-events: Fix memory leaks found on parse_events")
Cc Adrian Hunter <[email protected]>
Cc Alexander Shishkin <[email protected]>
Cc Andi Kleen <[email protected]>
Cc Jiri Olsa <[email protected]>
Cc Leo Yan <[email protected]>
Cc Mark Rutland <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Stephane Eranian <[email protected]>
---
 tools/perf/util/parse-events.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
tools/perf/util/parse-events.c +2 -1
index cce96b05d24c9..426f1984c143e 100644
@@ -1287,7 +1287,8 @@ int parse_events_add_pmu(struct parse_events_state *parse_state,
 
 		list_for_each_entry_safe(pos, tmp, &config_terms, list) {
 			list_del_init(&pos->list);
-			zfree(&pos->val.str);
+			if (pos->free_str)
+				zfree(&pos->val.str);
 			free(pos);
 		}
 		return -EINVAL;
Signature · 1 line
2.25.1
author maintainer
#55 lore raw

PATCH 56/206 powerpc/eeh: Only dump stack once if an MMIO loop is detected

In reply to Sasha Levin

From: Oliver O'Halloran <[email protected]>

[ Upstream commit 4e0942c0302b5ad76b228b1a7b8c09f658a1d58a ]

Many drivers don't check for errors when they get a 0xFFs response from an MMIO load. As a result after an EEH event occurs a driver can get stuck in a polling loop unless it some kind of internal timeout logic.

Currently EEH tries to detect and report stuck drivers by dumping a stack trace after eeh_dev_check_failure() is called EEH_MAX_FAILS times on an already frozen PE. The value of EEH_MAX_FAILS was chosen so that a dump would occur every few seconds if the driver was spinning in a loop. This results in a lot of spurious stack traces in the kernel log.

Fix this by limiting it to printing one stack trace for each PE freeze. If the driver is truely stuck the kernel's hung task detector is better suited to reporting the probelm anyway.

---
 arch/powerpc/kernel/eeh.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/powerpc/kernel/eeh.c +1 -1
index fe3c6f3bd3b62..d123cba0992d0 100644
@@ -502,7 +502,7 @@ int eeh_dev_check_failure(struct eeh_dev *edev)
 	rc = 1;
 	if (pe->state & EEH_PE_ISOLATED) {
 		pe->check_count++;
-		if (pe->check_count % EEH_MAX_FAILS == 0) {
+		if (pe->check_count == EEH_MAX_FAILS) {
 			dn = pci_device_to_OF_node(dev);
 			if (dn)
 				location = of_get_property(dn, "ibm,loc-code",
Signature · 1 line
2.25.1
author maintainer
#165 lore raw

PATCH 163/206 tty: serial: samsung: Correct clock selection logic

In reply to Sasha Levin

From: Jonathan Bakker <[email protected]>

[ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ]

Some variants of the samsung tty driver can pick which clock to use for their baud rate generation. In the DT conversion, a default clock was selected to be used if a specific one wasn't assigned and then a comparison of which clock rate worked better was done. Unfortunately, the comparison was implemented in such a way that only the default clock was ever actually compared. Fix this by iterating through all possible clocks, except when a specific clock has already been picked via clk_sel (which is only possible via board files).

---
 drivers/tty/serial/samsung.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/tty/serial/samsung.c +4 -4
index fcb89bf2524d1..1528a7ba2bf4d 100644
@@ -1187,14 +1187,14 @@ static unsigned int s3c24xx_serial_getclk(struct s3c24xx_uart_port *ourport,
 	struct s3c24xx_uart_info *info = ourport->info;
 	struct clk *clk;
 	unsigned long rate;
-	unsigned int cnt, baud, quot, clk_sel, best_quot = 0;
+	unsigned int cnt, baud, quot, best_quot = 0;
 	char clkname[MAX_CLK_NAME_LENGTH];
 	int calc_deviation, deviation = (1 << 30) - 1;
 
-	clk_sel = (ourport->cfg->clk_sel) ? ourport->cfg->clk_sel :
-			ourport->info->def_clk_sel;
 	for (cnt = 0; cnt < info->num_clks; cnt++) {
-		if (!(clk_sel & (1 << cnt)))
+		/* Keep selected clock if provided */
+		if (ourport->cfg->clk_sel &&
+			!(ourport->cfg->clk_sel & (1 << cnt)))
 			continue;
 
 		sprintf(clkname, "clk_uart_baud%d", cnt);
Signature · 1 line
2.25.1
author maintainer
#160 lore raw

PATCH 158/206 power: supply: max17040: Correct voltage reading

In reply to Sasha Levin

From: Jonathan Bakker <[email protected]>

[ Upstream commit 0383024f811aa469df258039807810fc3793a105 ]

According to the datasheet available at (1), the bottom four bits are always zero and the actual voltage is 1.25x this value in mV. Since the kernel API specifies that voltages should be in uV, it should report 1250x the shifted value.

1) https://datasheets.maximintegrated.com/en/ds/MAX17040-MAX17041.pdf

---
 drivers/power/supply/max17040_battery.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/power/supply/max17040_battery.c +1 -1
index 33c40f79d23d5..2c35c13ad546f 100644
@@ -109,7 +109,7 @@ static void max17040_get_vcell(struct i2c_client *client)
 
 	vcell = max17040_read_reg(client, MAX17040_VCELL);
 
-	chip->vcell = vcell;
+	chip->vcell = (vcell >> 4) * 1250;
 }
 
 static void max17040_get_soc(struct i2c_client *client)
Signature · 1 line
2.25.1
author maintainer
#163 lore raw

PATCH 161/206 USB: EHCI: ehci-mv: fix error handling in mv_ehci_probe()

In reply to Sasha Levin

From: Tang Bin <[email protected]>

[ Upstream commit c856b4b0fdb5044bca4c0acf9a66f3b5cc01a37a ]

If the function platform_get_irq() failed, the negative value returned will not be detected here. So fix error handling in mv_ehci_probe(). And when get irq failed, the function platform_get_irq() logs an error message, so remove redundant message here.

---
 drivers/usb/host/ehci-mv.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
drivers/usb/host/ehci-mv.c +2 -3
index de764459e05a6..4edcd7536a01b 100644
@@ -193,9 +193,8 @@ static int mv_ehci_probe(struct platform_device *pdev)
 	hcd->regs = ehci_mv->op_regs;
 
 	hcd->irq = platform_get_irq(pdev, 0);
-	if (!hcd->irq) {
-		dev_err(&pdev->dev, "Cannot get irq.");
-		retval = -ENODEV;
+	if (hcd->irq < 0) {
+		retval = hcd->irq;
 		goto err_disable_clk;
 	}
 
Signature · 1 line
2.25.1
author maintainer
#159 lore raw

PATCH 157/206 perf mem2node: Avoid double free related to realloc

In reply to Sasha Levin

From: Ian Rogers <[email protected]>

[ Upstream commit 266150c94c69429cf6d18e130237224a047f5061 ]

Realloc of size zero is a free not an error, avoid this causing a double free. Caught by clang's address sanitizer:

==2634==ERROR: AddressSanitizer: attempting double-free on 0x6020000015f0 in thread T0:

    #0 0x5649659297fd in free llvm/llvm-project/compiler-rt/lib/asan/asan_malloc_linux.cpp:123:3
    #1 0x5649659e9251 in __zfree tools/lib/zalloc.c:13:2
    #2 0x564965c0f92c in mem2node__exit tools/perf/util/mem2node.c:114:2
    #3 0x564965a08b4c in perf_c2c__report tools/perf/builtin-c2c.c:2867:2
    #4 0x564965a0616a in cmd_c2c tools/perf/builtin-c2c.c:2989:10
    #5 0x564965944348 in run_builtin tools/perf/perf.c:312:11
    #6 0x564965943235 in handle_internal_command tools/perf/perf.c:364:8
    #7 0x5649659440c4 in run_argv tools/perf/perf.c:408:2
    #8 0x564965942e41 in main tools/perf/perf.c:538:3

0x6020000015f0 is located 0 bytes inside of 1-byte region [0x6020000015f0,0x6020000015f1) freed by thread T0 here:

    #0 0x564965929da3 in realloc third_party/llvm/llvm-project/compiler-rt/lib/asan/asan_malloc_linux.cpp:164:3
    #1 0x564965c0f55e in mem2node__init tools/perf/util/mem2node.c:97:16
    #2 0x564965a08956 in perf_c2c__report tools/perf/builtin-c2c.c:2803:8
    #3 0x564965a0616a in cmd_c2c tools/perf/builtin-c2c.c:2989:10
    #4 0x564965944348 in run_builtin tools/perf/perf.c:312:11
    #5 0x564965943235 in handle_internal_command tools/perf/perf.c:364:8
    #6 0x5649659440c4 in run_argv tools/perf/perf.c:408:2
    #7 0x564965942e41 in main tools/perf/perf.c:538:3

previously allocated by thread T0 here:

    #0 0x564965929c42 in calloc third_party/llvm/llvm-project/compiler-rt/lib/asan/asan_malloc_linux.cpp:154:3
    #1 0x5649659e9220 in zalloc tools/lib/zalloc.c:8:9
    #2 0x564965c0f32d in mem2node__init tools/perf/util/mem2node.c:61:12
    #3 0x564965a08956 in perf_c2c__report tools/perf/builtin-c2c.c:2803:8
    #4 0x564965a0616a in cmd_c2c tools/perf/builtin-c2c.c:2989:10
    #5 0x564965944348 in run_builtin tools/perf/perf.c:312:11
    #6 0x564965943235 in handle_internal_command tools/perf/perf.c:364:8
    #7 0x5649659440c4 in run_argv tools/perf/perf.c:408:2
    #8 0x564965942e41 in main tools/perf/perf.c:538:3

v2: add a WARN_ON_ONCE when the free condition arises.

---
 tools/perf/util/mem2node.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
tools/perf/util/mem2node.c +2 -1
index c6fd81c025863..81c5a2e438b7d 100644
@@ -1,5 +1,6 @@
 #include <errno.h>
 #include <inttypes.h>
+#include <asm/bug.h>
 #include <linux/bitmap.h>
 #include "mem2node.h"
 #include "util.h"
@@ -92,7 +93,7 @@ int mem2node__init(struct mem2node *map, struct perf_env *env)
 
 	/* Cut unused entries, due to merging. */
 	tmp_entries = realloc(entries, sizeof(*entries) * j);
-	if (tmp_entries)
+	if (tmp_entries || WARN_ON_ONCE(j == 0))
 		entries = tmp_entries;
 
 	for (i = 0; i < j; i++) {
Signature · 1 line
2.25.1
author maintainer
#158 lore raw

PATCH 156/206 perf parse-events: Fix memory leaks found on parse_events

In reply to Sasha Levin

From: Ian Rogers <[email protected]>

[ Upstream commit e8dfb81838b14f82521968343884665b996646ef ]

Fix a memory leak found by applying LLVM's libfuzzer on parse_events().

Cc Adrian Hunter <[email protected]>
Cc Alexander Shishkin <[email protected]>
Cc Andi Kleen <[email protected]>
Cc Leo Yan <[email protected]>
Cc Mark Rutland <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Stephane Eranian <[email protected]>
[ split from a larger patch, use zfree() ]
---
 tools/perf/util/parse-events.c | 1 +
 1 file changed, 1 insertion(+)
tools/perf/util/parse-events.c +1 -0
index 6d087d9acd5ee..cce96b05d24c9 100644
@@ -1287,6 +1287,7 @@ int parse_events_add_pmu(struct parse_events_state *parse_state,
 
 		list_for_each_entry_safe(pos, tmp, &config_terms, list) {
 			list_del_init(&pos->list);
+			zfree(&pos->val.str);
 			free(pos);
 		}
 		return -EINVAL;
Signature · 1 line
2.25.1
author maintainer
#154 lore raw

PATCH 152/206 sparc64: vcc: Fix error return code in vcc_probe()

In reply to Sasha Levin

From: Wei Yongjun <[email protected]>

[ Upstream commit ff62255a2a5c1228a28f2bb063646f948115a309 ]

Fix to return negative error code -ENOMEM from the error handling case instead of 0, as done elsewhere in this function.

---
 drivers/tty/vcc.c | 1 +
 1 file changed, 1 insertion(+)
drivers/tty/vcc.c +1 -0
index 58b454c34560a..10a832a2135e2 100644
@@ -604,6 +604,7 @@ static int vcc_probe(struct vio_dev *vdev, const struct vio_device_id *id)
 	port->index = vcc_table_add(port);
 	if (port->index == -1) {
 		pr_err("VCC: no more TTY indices left for allocation\n");
+		rv = -ENOMEM;
 		goto free_ldc;
 	}
 
Signature · 1 line
2.25.1
author maintainer
#153 lore raw

PATCH 151/206 staging:r8188eu: avoid skb_clone for amsdu to msdu conversion

In reply to Sasha Levin

From: Ivan Safonov <[email protected]>

[ Upstream commit 628cbd971a927abe6388d44320e351c337b331e4 ]

skb clones use same data buffer,
so tail of one skb is corrupted by beginning of next skb.

---
 drivers/staging/rtl8188eu/core/rtw_recv.c | 19 ++++++-------------
 1 file changed, 6 insertions(+), 13 deletions(-)
drivers/staging/rtl8188eu/core/rtw_recv.c +6 -13
index 17b4b9257b495..0ddf41b5a734a 100644
@@ -1535,21 +1535,14 @@ static int amsdu_to_msdu(struct adapter *padapter, struct recv_frame *prframe)
 
 		/* Allocate new skb for releasing to upper layer */
 		sub_skb = dev_alloc_skb(nSubframe_Length + 12);
-		if (sub_skb) {
-			skb_reserve(sub_skb, 12);
-			skb_put_data(sub_skb, pdata, nSubframe_Length);
-		} else {
-			sub_skb = skb_clone(prframe->pkt, GFP_ATOMIC);
-			if (sub_skb) {
-				sub_skb->data = pdata;
-				sub_skb->len = nSubframe_Length;
-				skb_set_tail_pointer(sub_skb, nSubframe_Length);
-			} else {
-				DBG_88E("skb_clone() Fail!!! , nr_subframes=%d\n", nr_subframes);
-				break;
-			}
+		if (!sub_skb) {
+			DBG_88E("dev_alloc_skb() Fail!!! , nr_subframes=%d\n", nr_subframes);
+			break;
 		}
 
+		skb_reserve(sub_skb, 12);
+		skb_put_data(sub_skb, pdata, nSubframe_Length);
+
 		subframes[nr_subframes++] = sub_skb;
 
 		if (nr_subframes >= MAX_SUBFRAME_COUNT) {
Signature · 1 line
2.25.1
author maintainer
#151 lore raw

PATCH 149/206 net: openvswitch: use u64 for meter bucket

In reply to Sasha Levin

From: Tonghao Zhang <[email protected]>

[ Upstream commit e57358873bb5d6caa882b9684f59140912b37dde ]

When setting the meter rate to 4+Gbps, there is an overflow, the meters don't work as expected.

---
 net/openvswitch/meter.c | 2 +-
 net/openvswitch/meter.h | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
net/openvswitch/meter.c +1 -1
index c038e021a5916..6f5131d1074b0 100644
@@ -255,7 +255,7 @@ static struct dp_meter *dp_meter_create(struct nlattr **a)
 		 *
 		 * Start with a full bucket.
 		 */
-		band->bucket = (band->burst_size + band->rate) * 1000;
+		band->bucket = (band->burst_size + band->rate) * 1000ULL;
 		band_max_delta_t = band->bucket / band->rate;
 		if (band_max_delta_t > meter->max_delta_t)
 			meter->max_delta_t = band_max_delta_t;
net/openvswitch/meter.h +1 -1
index 964ace2650f89..970557ed5b5b6 100644
@@ -26,7 +26,7 @@ struct dp_meter_band {
 	u32 type;
 	u32 rate;
 	u32 burst_size;
-	u32 bucket; /* 1/1000 packets, or in bits */
+	u64 bucket; /* 1/1000 packets, or in bits */
 	struct ovs_flow_stats stats;
 };
 
Signature · 1 line
2.25.1
author maintainer
#152 lore raw

PATCH 150/206 scsi: aacraid: Fix error handling paths in aac_probe_one()

In reply to Sasha Levin

From: Christophe JAILLET <[email protected]>

[ Upstream commit f7854c382240c1686900b2f098b36430c6f5047e ]

If 'scsi_host_alloc()' or 'kcalloc()' fail, 'error' is known to be 0. Set it explicitly to -ENOMEM before branching to the error handling path.

While at it, remove 2 useless assignments to 'error'. These values are overwridden a few lines later.

---
 drivers/scsi/aacraid/linit.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
drivers/scsi/aacraid/linit.c +8 -4
index 0142547aaadd2..eecffc03084c0 100644
@@ -1620,7 +1620,7 @@ static int aac_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	struct Scsi_Host *shost;
 	struct aac_dev *aac;
 	struct list_head *insert = &aac_devices;
-	int error = -ENODEV;
+	int error;
 	int unique_id = 0;
 	u64 dmamask;
 	int mask_bits = 0;
@@ -1645,7 +1645,6 @@ static int aac_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	error = pci_enable_device(pdev);
 	if (error)
 		goto out;
-	error = -ENODEV;
 
 	if (!(aac_drivers[index].quirks & AAC_QUIRK_SRC)) {
 		error = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
@@ -1677,8 +1676,10 @@ static int aac_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	pci_set_master(pdev);
 
 	shost = scsi_host_alloc(&aac_driver_template, sizeof(struct aac_dev));
-	if (!shost)
+	if (!shost) {
+		error = -ENOMEM;
 		goto out_disable_pdev;
+	}
 
 	shost->irq = pdev->irq;
 	shost->unique_id = unique_id;
@@ -1703,8 +1704,11 @@ static int aac_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	aac->fibs = kcalloc(shost->can_queue + AAC_NUM_MGT_FIB,
 			    sizeof(struct fib),
 			    GFP_KERNEL);
-	if (!aac->fibs)
+	if (!aac->fibs) {
+		error = -ENOMEM;
 		goto out_free_host;
+	}
+
 	spin_lock_init(&aac->fib_lock);
 
 	mutex_init(&aac->ioctl_mutex);
Signature · 1 line
2.25.1
author maintainer
#149 lore raw

PATCH 147/206 drivers: char: tlclk.c: Avoid data race between init and interrupt handler

In reply to Sasha Levin

From: Madhuparna Bhowmik <[email protected]>

[ Upstream commit 44b8fb6eaa7c3fb770bf1e37619cdb3902cca1fc ]

After registering character device the file operation callbacks can be called. The open callback registers interrupt handler. Therefore interrupt handler can execute in parallel with rest of the init function. To avoid such data race initialize telclk_interrupt variable and struct alarm_events before registering character device.

Found by Linux Driver Verification project (linuxtesting.org).

---
 drivers/char/tlclk.c | 17 ++++++++++-------
 1 file changed, 10 insertions(+), 7 deletions(-)
drivers/char/tlclk.c +10 -7
index 8eeb4190207d1..dce22b7fc5449 100644
@@ -776,17 +776,21 @@ static int __init tlclk_init(void)
 {
 	int ret;
 
+	telclk_interrupt = (inb(TLCLK_REG7) & 0x0f);
+
+	alarm_events = kzalloc( sizeof(struct tlclk_alarms), GFP_KERNEL);
+	if (!alarm_events) {
+		ret = -ENOMEM;
+		goto out1;
+	}
+
 	ret = register_chrdev(tlclk_major, "telco_clock", &tlclk_fops);
 	if (ret < 0) {
 		printk(KERN_ERR "tlclk: can't get major %d.\n", tlclk_major);
+		kfree(alarm_events);
 		return ret;
 	}
 	tlclk_major = ret;
-	alarm_events = kzalloc( sizeof(struct tlclk_alarms), GFP_KERNEL);
-	if (!alarm_events) {
-		ret = -ENOMEM;
-		goto out1;
-	}
 
 	/* Read telecom clock IRQ number (Set by BIOS) */
 	if (!request_region(TLCLK_BASE, 8, "telco_clock")) {
@@ -795,7 +799,6 @@ static int __init tlclk_init(void)
 		ret = -EBUSY;
 		goto out2;
 	}
-	telclk_interrupt = (inb(TLCLK_REG7) & 0x0f);
 
 	if (0x0F == telclk_interrupt ) { /* not MCPBL0010 ? */
 		printk(KERN_ERR "telclk_interrupt = 0x%x non-mcpbl0010 hw.\n",
@@ -836,8 +839,8 @@ out3:
 	release_region(TLCLK_BASE, 8);
 out2:
 	kfree(alarm_events);
-out1:
 	unregister_chrdev(tlclk_major, "telco_clock");
+out1:
 	return ret;
 }
 
Signature · 1 line
2.25.1
author maintainer
#148 lore raw

PATCH 146/206 bdev: Reduce time holding bd_mutex in sync in blkdev_close()

In reply to Sasha Levin

From: Douglas Anderson <[email protected]>

[ Upstream commit b849dd84b6ccfe32622988b79b7b073861fcf9f7 ]

While trying to "dd" to the block device for a USB stick, I encountered a hung task warning (blocked for > 120 seconds). I managed to come up with an easy way to reproduce this on my system (where /dev/sdb is the block device for my USB stick) with:

while true; do dd if=/dev/zero of=/dev/sdb bs=4M; done

With my reproduction here are the relevant bits from the hung task detector:

 INFO: task udevd:294 blocked for more than 122 seconds.
 ...
 udevd           D    0   294      1 0x00400008
 Call trace:
  ...
  mutex_lock_nested+0x40/0x50
  __blkdev_get+0x7c/0x3d4
  blkdev_get+0x118/0x138
  blkdev_open+0x94/0xa8
  do_dentry_open+0x268/0x3a0
  vfs_open+0x34/0x40
  path_openat+0x39c/0xdf4
  do_filp_open+0x90/0x10c
  do_sys_open+0x150/0x3c8
  ...

...

 Showing all locks held in the system:
 ...
 1 lock held by dd/2798:
  #0: ffffff814ac1a3b8 (&bdev->bd_mutex){+.+.}, at: __blkdev_put+0x50/0x204
 ...
 dd              D    0  2798   2764 0x00400208
 Call trace:
  ...
  schedule+0x8c/0xbc
  io_schedule+0x1c/0x40
  wait_on_page_bit_common+0x238/0x338
  __lock_page+0x5c/0x68
  write_cache_pages+0x194/0x500
  generic_writepages+0x64/0xa4
  blkdev_writepages+0x24/0x30
  do_writepages+0x48/0xa8
  __filemap_fdatawrite_range+0xac/0xd8
  filemap_write_and_wait+0x30/0x84
  __blkdev_put+0x88/0x204
  blkdev_put+0xc4/0xe4
  blkdev_close+0x28/0x38
  __fput+0xe0/0x238
  ____fput+0x1c/0x28
  task_work_run+0xb0/0xe4
  do_notify_resume+0xfc0/0x14bc
  work_pending+0x8/0x14

The problem appears related to the fact that my USB disk is terribly slow and that I have a lot of RAM in my system to cache things. Specifically my writes seem to be happening at ~15 MB/s and I've got ~4 GB of RAM in my system that can be used for buffering. To write 4 GB of buffer to disk thus takes ~4000 MB / ~15 MB/s = ~267 seconds.

The 267 second number is a problem because in __blkdev_put() we call sync_blockdev() while holding the bd_mutex. Any other callers who want the bd_mutex will be blocked for the whole time.

The problem is made worse because I believe blkdev_put() specifically tells other tasks (namely udev) to go try to access the device at right around the same time we're going to hold the mutex for a long time.

Putting some traces around this (after disabling the hung task detector), I could confirm:
dd: 437.608600: __blkdev_put() right before sync_blockdev() for sdb
udevd: 437.623901: blkdev_open() right before blkdev_get() for sdb
dd: 661.468451: __blkdev_put() right after sync_blockdev() for sdb
udevd: 663.820426: blkdev_open() right after blkdev_get() for sdb

A simple fix for this is to realize that sync_blockdev() works fine if you're not holding the mutex. Also, it's not the end of the world if you sync a little early (though it can have performance impacts). Thus we can make a guess that we're going to need to do the sync and then do it without holding the mutex. We still do one last sync with the mutex but it should be much, much faster.

With this, my hung task warnings for my test case are gone.

---
 fs/block_dev.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
fs/block_dev.c +10 -0
index 8ac8f7469354b..9f3faac490259 100644
@@ -1793,6 +1793,16 @@ static void __blkdev_put(struct block_device *bdev, fmode_t mode, int for_part)
 	struct gendisk *disk = bdev->bd_disk;
 	struct block_device *victim = NULL;
 
+	/*
+	 * Sync early if it looks like we're the last one.  If someone else
+	 * opens the block device between now and the decrement of bd_openers
+	 * then we did a sync that we didn't need to, but that's not the end
+	 * of the world and we want to avoid long (could be several minute)
+	 * syncs while holding the mutex.
+	 */
+	if (bdev->bd_openers == 1)
+		sync_blockdev(bdev);
+
 	mutex_lock_nested(&bdev->bd_mutex, for_part);
 	if (for_part)
 		bdev->bd_part_count--;
Signature · 1 line
2.25.1
author maintainer
#146 lore raw

PATCH 144/206 KVM: Remove CREATE_IRQCHIP/SET_PIT2 race

In reply to Sasha Levin

From: Steve Rutherford <[email protected]>

[ Upstream commit 7289fdb5dcdbc5155b5531529c44105868a762f2 ]

Fixes a NULL pointer dereference, caused by the PIT firing an interrupt before the interrupt table has been initialized.

SET_PIT2 can race with the creation of the IRQchip. In particular, if SET_PIT2 is called with a low PIT timer period (after the creation of the IOAPIC, but before the instantiation of the irq routes), the PIT can fire an interrupt at an uninitialized table.

Message-Id: <[email protected]>

---
 arch/x86/kvm/x86.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)
arch/x86/kvm/x86.c +8 -2
index 430a4bc66f604..620ed1fa35119 100644
@@ -4668,10 +4668,13 @@ set_identity_unlock:
 		r = -EFAULT;
 		if (copy_from_user(&u.ps, argp, sizeof u.ps))
 			goto out;
+		mutex_lock(&kvm->lock);
 		r = -ENXIO;
 		if (!kvm->arch.vpit)
-			goto out;
+			goto set_pit_out;
 		r = kvm_vm_ioctl_set_pit(kvm, &u.ps);
+set_pit_out:
+		mutex_unlock(&kvm->lock);
 		break;
 	}
 	case KVM_GET_PIT2: {
@@ -4691,10 +4694,13 @@ set_identity_unlock:
 		r = -EFAULT;
 		if (copy_from_user(&u.ps2, argp, sizeof(u.ps2)))
 			goto out;
+		mutex_lock(&kvm->lock);
 		r = -ENXIO;
 		if (!kvm->arch.vpit)
-			goto out;
+			goto set_pit2_out;
 		r = kvm_vm_ioctl_set_pit2(kvm, &u.ps2);
+set_pit2_out:
+		mutex_unlock(&kvm->lock);
 		break;
 	}
 	case KVM_REINJECT_CONTROL: {
Signature · 1 line
2.25.1
author maintainer
#144 lore raw

PATCH 142/206 scsi: qedi: Fix termination timeouts in session logout

In reply to Sasha Levin

From: Nilesh Javali <[email protected]>

[ Upstream commit b9b97e6903032ec56e6dcbe137a9819b74a17fea ]

The destroy connection ramrod timed out during session logout. Fix the wait delay for graceful vs abortive termination as per the FW requirements.

---
 drivers/scsi/qedi/qedi_iscsi.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/scsi/qedi/qedi_iscsi.c +3 -0
index 751941a3ed303..aa451c8b49e56 100644
@@ -1065,6 +1065,9 @@ static void qedi_ep_disconnect(struct iscsi_endpoint *ep)
 		break;
 	}
 
+	if (!abrt_conn)
+		wait_delay += qedi->pf_params.iscsi_pf_params.two_msl_timer;
+
 	qedi_ep->state = EP_STATE_DISCONN_START;
 	ret = qedi_ops->destroy_conn(qedi->cdev, qedi_ep->handle, abrt_conn);
 	if (ret) {
Signature · 1 line
2.25.1
author maintainer
#142 lore raw

PATCH 140/206 nvmet-rdma: fix double free of rdma queue

In reply to Sasha Levin

From: Israel Rukshin <[email protected]>

[ Upstream commit 21f9024355e58772ec5d7fc3534aa5e29d72a8b6 ]

In case rdma accept fails at nvmet_rdma_queue_connect(), release work is scheduled. Later on, a new RDMA CM event may arrive since we didn't destroy the cm-id and call nvmet_rdma_queue_connect_fail(), which schedule another release work. This will cause calling nvmet_rdma_free_queue twice. To fix this we implicitly destroy the cm_id with non-zero ret code, which guarantees that new rdma_cm events will not arrive afterwards. Also add a qp pointer to nvmet_rdma_queue structure, so we can use it when the cm_id pointer is NULL or was destroyed.

---
 drivers/nvme/target/rdma.c | 30 ++++++++++++++++++------------
 1 file changed, 18 insertions(+), 12 deletions(-)
drivers/nvme/target/rdma.c +18 -12
index 08f997a390d5d..cfd26437aeaea 100644
@@ -83,6 +83,7 @@ enum nvmet_rdma_queue_state {
 
 struct nvmet_rdma_queue {
 	struct rdma_cm_id	*cm_id;
+	struct ib_qp		*qp;
 	struct nvmet_port	*port;
 	struct ib_cq		*cq;
 	atomic_t		sq_wr_avail;
@@ -471,7 +472,7 @@ static int nvmet_rdma_post_recv(struct nvmet_rdma_device *ndev,
 	if (ndev->srq)
 		ret = ib_post_srq_recv(ndev->srq, &cmd->wr, NULL);
 	else
-		ret = ib_post_recv(cmd->queue->cm_id->qp, &cmd->wr, NULL);
+		ret = ib_post_recv(cmd->queue->qp, &cmd->wr, NULL);
 
 	if (unlikely(ret))
 		pr_err("post_recv cmd failed\n");
@@ -510,7 +511,7 @@ static void nvmet_rdma_release_rsp(struct nvmet_rdma_rsp *rsp)
 	atomic_add(1 + rsp->n_rdma, &queue->sq_wr_avail);
 
 	if (rsp->n_rdma) {
-		rdma_rw_ctx_destroy(&rsp->rw, queue->cm_id->qp,
+		rdma_rw_ctx_destroy(&rsp->rw, queue->qp,
 				queue->cm_id->port_num, rsp->req.sg,
 				rsp->req.sg_cnt, nvmet_data_dir(&rsp->req));
 	}
@@ -594,7 +595,7 @@ static void nvmet_rdma_read_data_done(struct ib_cq *cq, struct ib_wc *wc)
 
 	WARN_ON(rsp->n_rdma <= 0);
 	atomic_add(rsp->n_rdma, &queue->sq_wr_avail);
-	rdma_rw_ctx_destroy(&rsp->rw, queue->cm_id->qp,
+	rdma_rw_ctx_destroy(&rsp->rw, queue->qp,
 			queue->cm_id->port_num, rsp->req.sg,
 			rsp->req.sg_cnt, nvmet_data_dir(&rsp->req));
 	rsp->n_rdma = 0;
@@ -737,7 +738,7 @@ static bool nvmet_rdma_execute_command(struct nvmet_rdma_rsp *rsp)
 	}
 
 	if (nvmet_rdma_need_data_in(rsp)) {
-		if (rdma_rw_ctx_post(&rsp->rw, queue->cm_id->qp,
+		if (rdma_rw_ctx_post(&rsp->rw, queue->qp,
 				queue->cm_id->port_num, &rsp->read_cqe, NULL))
 			nvmet_req_complete(&rsp->req, NVME_SC_DATA_XFER_ERROR);
 	} else {
@@ -1020,6 +1021,7 @@ static int nvmet_rdma_create_queue_ib(struct nvmet_rdma_queue *queue)
 		pr_err("failed to create_qp ret= %d\n", ret);
 		goto err_destroy_cq;
 	}
+	queue->qp = queue->cm_id->qp;
 
 	atomic_set(&queue->sq_wr_avail, qp_attr.cap.max_send_wr);
 
@@ -1048,11 +1050,10 @@ err_destroy_cq:
 
 static void nvmet_rdma_destroy_queue_ib(struct nvmet_rdma_queue *queue)
 {
-	struct ib_qp *qp = queue->cm_id->qp;
-
-	ib_drain_qp(qp);
-	rdma_destroy_id(queue->cm_id);
-	ib_destroy_qp(qp);
+	ib_drain_qp(queue->qp);
+	if (queue->cm_id)
+		rdma_destroy_id(queue->cm_id);
+	ib_destroy_qp(queue->qp);
 	ib_free_cq(queue->cq);
 }
 
@@ -1286,9 +1287,12 @@ static int nvmet_rdma_queue_connect(struct rdma_cm_id *cm_id,
 
 	ret = nvmet_rdma_cm_accept(cm_id, queue, &event->param.conn);
 	if (ret) {
-		schedule_work(&queue->release_work);
-		/* Destroying rdma_cm id is not needed here */
-		return 0;
+		/*
+		 * Don't destroy the cm_id in free path, as we implicitly
+		 * destroy the cm_id here with non-zero ret code.
+		 */
+		queue->cm_id = NULL;
+		goto free_queue;
 	}
 
 	mutex_lock(&nvmet_rdma_queue_mutex);
@@ -1297,6 +1301,8 @@ static int nvmet_rdma_queue_connect(struct rdma_cm_id *cm_id,
 
 	return 0;
 
+free_queue:
+	nvmet_rdma_free_queue(queue);
 put_device:
 	kref_put(&ndev->ref, nvmet_rdma_free_dev);
 
Signature · 1 line
2.25.1
author maintainer
#133 lore raw

PATCH 131/206 svcrdma: Fix leak of transport addresses

In reply to Sasha Levin

From: Chuck Lever <[email protected]>

[ Upstream commit 1a33d8a284b1e85e03b8c7b1ea8fb985fccd1d71 ]

Kernel memory leak detected:

unreferenced object 0xffff888849cdf480 (size 8):
comm "kworker/u8:3", pid 2086, jiffies 4297898756 (age 4269.856s) hex dump (first 8 bytes):

    30 00 cd 49 88 88 ff ff                          0..I....
  backtrace:
    [<00000000acfc370b>] __kmalloc_track_caller+0x137/0x183
    [<00000000a2724354>] kstrdup+0x2b/0x43
    [<0000000082964f84>] xprt_rdma_format_addresses+0x114/0x17d [rpcrdma]
    [<00000000dfa6ed00>] xprt_setup_rdma_bc+0xc0/0x10c [rpcrdma]
    [<0000000073051a83>] xprt_create_transport+0x3f/0x1a0 [sunrpc]
    [<0000000053531a8e>] rpc_create+0x118/0x1cd [sunrpc]
    [<000000003a51b5f8>] setup_callback_client+0x1a5/0x27d [nfsd]
    [<000000001bd410af>] nfsd4_process_cb_update.isra.7+0x16c/0x1ac [nfsd]
    [<000000007f4bbd56>] nfsd4_run_cb_work+0x4c/0xbd [nfsd]
    [<0000000055c5586b>] process_one_work+0x1b2/0x2fe
    [<00000000b1e3e8ef>] worker_thread+0x1a6/0x25a
    [<000000005205fb78>] kthread+0xf6/0xfb
    [<000000006d2dc057>] ret_from_fork+0x3a/0x50

Introduce a call to xprt_rdma_free_addresses() similar to the way that the TCP backchannel releases a transport's peer address strings.

Fixes 5d252f90a800 ("svcrdma: Add class for RDMA backwards direction transport")
---
 net/sunrpc/xprtrdma/svc_rdma_backchannel.c | 1 +
 1 file changed, 1 insertion(+)
net/sunrpc/xprtrdma/svc_rdma_backchannel.c +1 -0
index b9827665ff355..d183d4aee822c 100644
@@ -256,6 +256,7 @@ xprt_rdma_bc_put(struct rpc_xprt *xprt)
 {
 	dprintk("svcrdma: %s: xprt %p\n", __func__, xprt);
 
+	xprt_rdma_free_addresses(xprt);
 	xprt_free(xprt);
 	module_put(THIS_MODULE);
 }
Signature · 1 line
2.25.1
author maintainer
#138 lore raw

PATCH 136/206 NFS: Fix races nfs_page_group_destroy() vs nfs_destroy_unlinked_subrequests()

In reply to Sasha Levin

From: Trond Myklebust <[email protected]>

[ Upstream commit 08ca8b21f760c0ed5034a5c122092eec22ccf8f4 ]

When a subrequest is being detached from the subgroup, we want to ensure that it is not holding the group lock, or in the process of waiting for the group lock.

Fixes 5b2b5187fa85 ("NFS: Fix nfs_page_group_destroy() and nfs_lock_and_join_requests() race cases")
---
 fs/nfs/pagelist.c        | 67 +++++++++++++++++++++++++++-------------
 fs/nfs/write.c           | 10 ++++--
 include/linux/nfs_page.h |  2 ++
 3 files changed, 55 insertions(+), 24 deletions(-)
fs/nfs/pagelist.c +45 -22
index 5dae7c85d9b6e..2c7d76b4c5e18 100644
@@ -132,47 +132,70 @@ nfs_async_iocounter_wait(struct rpc_task *task, struct nfs_lock_context *l_ctx)
 EXPORT_SYMBOL_GPL(nfs_async_iocounter_wait);
 
 /*
- * nfs_page_group_lock - lock the head of the page group
- * @req - request in group that is to be locked
+ * nfs_page_set_headlock - set the request PG_HEADLOCK
+ * @req: request that is to be locked
  *
- * this lock must be held when traversing or modifying the page
- * group list
+ * this lock must be held when modifying req->wb_head
  *
  * return 0 on success, < 0 on error
  */
 int
-nfs_page_group_lock(struct nfs_page *req)
+nfs_page_set_headlock(struct nfs_page *req)
 {
-	struct nfs_page *head = req->wb_head;
-
-	WARN_ON_ONCE(head != head->wb_head);
-
-	if (!test_and_set_bit(PG_HEADLOCK, &head->wb_flags))
+	if (!test_and_set_bit(PG_HEADLOCK, &req->wb_flags))
 		return 0;
 
-	set_bit(PG_CONTENDED1, &head->wb_flags);
+	set_bit(PG_CONTENDED1, &req->wb_flags);
 	smp_mb__after_atomic();
-	return wait_on_bit_lock(&head->wb_flags, PG_HEADLOCK,
+	return wait_on_bit_lock(&req->wb_flags, PG_HEADLOCK,
 				TASK_UNINTERRUPTIBLE);
 }
 
 /*
- * nfs_page_group_unlock - unlock the head of the page group
- * @req - request in group that is to be unlocked
+ * nfs_page_clear_headlock - clear the request PG_HEADLOCK
+ * @req: request that is to be locked
  */
 void
-nfs_page_group_unlock(struct nfs_page *req)
+nfs_page_clear_headlock(struct nfs_page *req)
 {
-	struct nfs_page *head = req->wb_head;
-
-	WARN_ON_ONCE(head != head->wb_head);
-
 	smp_mb__before_atomic();
-	clear_bit(PG_HEADLOCK, &head->wb_flags);
+	clear_bit(PG_HEADLOCK, &req->wb_flags);
 	smp_mb__after_atomic();
-	if (!test_bit(PG_CONTENDED1, &head->wb_flags))
+	if (!test_bit(PG_CONTENDED1, &req->wb_flags))
 		return;
-	wake_up_bit(&head->wb_flags, PG_HEADLOCK);
+	wake_up_bit(&req->wb_flags, PG_HEADLOCK);
+}
+
+/*
+ * nfs_page_group_lock - lock the head of the page group
+ * @req: request in group that is to be locked
+ *
+ * this lock must be held when traversing or modifying the page
+ * group list
+ *
+ * return 0 on success, < 0 on error
+ */
+int
+nfs_page_group_lock(struct nfs_page *req)
+{
+	int ret;
+
+	ret = nfs_page_set_headlock(req);
+	if (ret || req->wb_head == req)
+		return ret;
+	return nfs_page_set_headlock(req->wb_head);
+}
+
+/*
+ * nfs_page_group_unlock - unlock the head of the page group
+ * @req: request in group that is to be unlocked
+ */
+void
+nfs_page_group_unlock(struct nfs_page *req)
+{
+	if (req != req->wb_head)
+		nfs_page_clear_headlock(req->wb_head);
+	nfs_page_clear_headlock(req);
 }
 
 /*
fs/nfs/write.c +8 -2
index 63d20308a9bb7..d419d89b91f7c 100644
@@ -416,22 +416,28 @@ nfs_destroy_unlinked_subrequests(struct nfs_page *destroy_list,
 		destroy_list = (subreq->wb_this_page == old_head) ?
 				   NULL : subreq->wb_this_page;
 
+		/* Note: lock subreq in order to change subreq->wb_head */
+		nfs_page_set_headlock(subreq);
 		WARN_ON_ONCE(old_head != subreq->wb_head);
 
 		/* make sure old group is not used */
 		subreq->wb_this_page = subreq;
+		subreq->wb_head = subreq;
 
 		clear_bit(PG_REMOVE, &subreq->wb_flags);
 
 		/* Note: races with nfs_page_group_destroy() */
 		if (!kref_read(&subreq->wb_kref)) {
 			/* Check if we raced with nfs_page_group_destroy() */
-			if (test_and_clear_bit(PG_TEARDOWN, &subreq->wb_flags))
+			if (test_and_clear_bit(PG_TEARDOWN, &subreq->wb_flags)) {
+				nfs_page_clear_headlock(subreq);
 				nfs_free_request(subreq);
+			} else
+				nfs_page_clear_headlock(subreq);
 			continue;
 		}
+		nfs_page_clear_headlock(subreq);
 
-		subreq->wb_head = subreq;
 		nfs_release_request(old_head);
 
 		if (test_and_clear_bit(PG_INODE_REF, &subreq->wb_flags)) {
include/linux/nfs_page.h +2 -0
index ad69430fd0eb5..5162fc1533c2f 100644
@@ -142,6 +142,8 @@ extern	void nfs_unlock_and_release_request(struct nfs_page *);
 extern int nfs_page_group_lock(struct nfs_page *);
 extern void nfs_page_group_unlock(struct nfs_page *);
 extern bool nfs_page_group_sync_on_bit(struct nfs_page *, unsigned int);
+extern	int nfs_page_set_headlock(struct nfs_page *req);
+extern void nfs_page_clear_headlock(struct nfs_page *req);
 extern bool nfs_async_iocounter_wait(struct rpc_task *, struct nfs_lock_context *);
 
 /*
Signature · 1 line
2.25.1
author maintainer
#137 lore raw

PATCH 135/206 PCI: pciehp: Fix MSI interrupt race

In reply to Sasha Levin

From: Stuart Hayes <[email protected]>

[ Upstream commit 8edf5332c39340b9583cf9cba659eb7ec71f75b5 ]

Without this commit, a PCIe hotplug port can stop generating interrupts on hotplug events, so device adds and removals will not be seen:

The pciehp interrupt handler pciehp_isr() reads the Slot Status register and then writes back to it to clear the bits that caused the interrupt. If a different interrupt event bit gets set between the read and the write, pciehp_isr() returns without having cleared all of the interrupt event bits. If this happens when the MSI isn't masked (which by default it isn't in handle_edge_irq(), and which it will never be when MSI per-vector masking is not supported), we won't get any more hotplug interrupts from that device.

That is expected behavior, according to the PCIe Base Spec r5.0, section 6.7.3.4, "Software Notification of Hot-Plug Events".

Because the Presence Detect Changed and Data Link Layer State Changed event bits can both get set at nearly the same time when a device is added or removed, this is more likely to happen than it might seem. The issue was found (and can be reproduced rather easily) by connecting and disconnecting an NVMe storage device on at least one system model where the NVMe devices were being connected to an AMD PCIe port (PCI device 0x1022/0x1483).

Fix the issue by modifying pciehp_isr() to loop back and re-read the Slot Status register immediately after writing to it, until it sees that all of the event status bits have been cleared.

[lukas: drop loop count limitation, write "events" instead of "status", don't loop back in INTx and poll modes, tweak code comment & commit msg]

---
 drivers/pci/hotplug/pciehp_hpc.c | 26 ++++++++++++++++++++------
 1 file changed, 20 insertions(+), 6 deletions(-)
drivers/pci/hotplug/pciehp_hpc.c +20 -6
index 07940d1d83b70..005817e40ad39 100644
@@ -530,7 +530,7 @@ static irqreturn_t pciehp_isr(int irq, void *dev_id)
 	struct controller *ctrl = (struct controller *)dev_id;
 	struct pci_dev *pdev = ctrl_dev(ctrl);
 	struct device *parent = pdev->dev.parent;
-	u16 status, events;
+	u16 status, events = 0;
 
 	/*
 	 * Interrupts only occur in D3hot or shallower (PCIe r4.0, sec 6.7.3.4).
@@ -553,6 +553,7 @@ static irqreturn_t pciehp_isr(int irq, void *dev_id)
 		}
 	}
 
+read_status:
 	pcie_capability_read_word(pdev, PCI_EXP_SLTSTA, &status);
 	if (status == (u16) ~0) {
 		ctrl_info(ctrl, "%s: no response from device\n", __func__);
@@ -565,24 +566,37 @@ static irqreturn_t pciehp_isr(int irq, void *dev_id)
 	 * Slot Status contains plain status bits as well as event
 	 * notification bits; right now we only want the event bits.
 	 */
-	events = status & (PCI_EXP_SLTSTA_ABP | PCI_EXP_SLTSTA_PFD |
-			   PCI_EXP_SLTSTA_PDC | PCI_EXP_SLTSTA_CC |
-			   PCI_EXP_SLTSTA_DLLSC);
+	status &= PCI_EXP_SLTSTA_ABP | PCI_EXP_SLTSTA_PFD |
+		  PCI_EXP_SLTSTA_PDC | PCI_EXP_SLTSTA_CC |
+		  PCI_EXP_SLTSTA_DLLSC;
 
 	/*
 	 * If we've already reported a power fault, don't report it again
 	 * until we've done something to handle it.
 	 */
 	if (ctrl->power_fault_detected)
-		events &= ~PCI_EXP_SLTSTA_PFD;
+		status &= ~PCI_EXP_SLTSTA_PFD;
 
+	events |= status;
 	if (!events) {
 		if (parent)
 			pm_runtime_put(parent);
 		return IRQ_NONE;
 	}
 
-	pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, events);
+	if (status) {
+		pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, events);
+
+		/*
+		 * In MSI mode, all event bits must be zero before the port
+		 * will send a new interrupt (PCIe Base Spec r5.0 sec 6.7.3.4).
+		 * So re-read the Slot Status register in case a bit was set
+		 * between read and write.
+		 */
+		if (pci_dev_msi_enabled(pdev) && !pciehp_poll_mode)
+			goto read_status;
+	}
+
 	ctrl_dbg(ctrl, "pending interrupts %#06x from Slot Status\n", events);
 	if (parent)
 		pm_runtime_put(parent);
Signature · 1 line
2.25.1
author maintainer
#132 lore raw

PATCH 130/206 SUNRPC: Fix a potential buffer overflow in 'svc_print_xprts()'

In reply to Sasha Levin

From: Christophe JAILLET <[email protected]>

[ Upstream commit b25b60d7bfb02a74bc3c2d998e09aab159df8059 ]

'maxlen' is the total size of the destination buffer. There is only one caller and this value is 256.

When we compute the size already used and what we would like to add in the buffer, the trailling NULL character is not taken into account. However, this trailling character will be added by the 'strcat' once we have checked that we have enough place.

So, there is a off-by-one issue and 1 byte of the stack could be erroneously overwridden.

Take into account the trailling NULL, when checking if there is enough place in the destination buffer.

While at it, also replace a 'sprintf' by a safer 'snprintf', check for output truncation and avoid a superfluous 'strlen'.

Fixes dc9a16e49dbba ("svc: Add /proc/sys/sunrpc/transport files")

[ cel: very minor fix to documenting comment

---
 net/sunrpc/svc_xprt.c | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)
net/sunrpc/svc_xprt.c +14 -5
index c8ee8e801edb8..709c082dc9059 100644
@@ -103,8 +103,17 @@ void svc_unreg_xprt_class(struct svc_xprt_class *xcl)
 }
 EXPORT_SYMBOL_GPL(svc_unreg_xprt_class);
 
-/*
- * Format the transport list for printing
+/**
+ * svc_print_xprts - Format the transport list for printing
+ * @buf: target buffer for formatted address
+ * @maxlen: length of target buffer
+ *
+ * Fills in @buf with a string containing a list of transport names, each name
+ * terminated with '\n'. If the buffer is too small, some entries may be
+ * missing, but it is guaranteed that all lines in the output buffer are
+ * complete.
+ *
+ * Returns positive length of the filled-in string.
  */
 int svc_print_xprts(char *buf, int maxlen)
 {
@@ -117,9 +126,9 @@ int svc_print_xprts(char *buf, int maxlen)
 	list_for_each_entry(xcl, &svc_xprt_class_list, xcl_list) {
 		int slen;
 
-		sprintf(tmpstr, "%s %d\n", xcl->xcl_name, xcl->xcl_max_payload);
-		slen = strlen(tmpstr);
-		if (len + slen > maxlen)
+		slen = snprintf(tmpstr, sizeof(tmpstr), "%s %d\n",
+				xcl->xcl_name, xcl->xcl_max_payload);
+		if (slen >= sizeof(tmpstr) || len + slen >= maxlen)
 			break;
 		len += slen;
 		strcat(buf, tmpstr);
Signature · 1 line
2.25.1
author maintainer
#130 lore raw

PATCH 128/206 RDMA/rxe: Set sys_image_guid to be aligned with HW IB devices

In reply to Sasha Levin

From: Zhu Yanjun <[email protected]>

[ Upstream commit d0ca2c35dd15a3d989955caec02beea02f735ee6 ]

The RXE driver doesn't set sys_image_guid and user space applications see zeros. This causes to pyverbs tests to fail with the following traceback, because the IBTA spec requires to have valid sys_image_guid.

Traceback (most recent call last):
File "./tests/test_device.py", line 51, in test_query_device
self.verify_device_attr(attr)
File "./tests/test_device.py", line 74, in verify_device_attr

     assert attr.sys_image_guid != 0

In order to fix it, set sys_image_guid to be equal to node_guid.

Before:
5: rxe0: ... node_guid 5054:00ff:feaa:5363 sys_image_guid 0000:0000:0000:0000

After:
5: rxe0: ... node_guid 5054:00ff:feaa:5363 sys_image_guid 5054:00ff:feaa:5363

---
 drivers/infiniband/sw/rxe/rxe.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/infiniband/sw/rxe/rxe.c +2 -0
index 10999fa692818..157d08f167345 100644
@@ -121,6 +121,8 @@ static void rxe_init_device_param(struct rxe_dev *rxe)
 	rxe->attr.max_fast_reg_page_list_len	= RXE_MAX_FMR_PAGE_LIST_LEN;
 	rxe->attr.max_pkeys			= RXE_MAX_PKEYS;
 	rxe->attr.local_ca_ack_delay		= RXE_LOCAL_CA_ACK_DELAY;
+	addrconf_addr_eui48((unsigned char *)&rxe->attr.sys_image_guid,
+			rxe->ndev->dev_addr);
 
 	rxe->max_ucontext			= RXE_MAX_UCONTEXT;
 }
Signature · 1 line
2.25.1
author maintainer
#131 lore raw

PATCH 129/206 scsi: hpsa: correct race condition in offload enabled

In reply to Sasha Levin

From: Don Brace <[email protected]>

[ Upstream commit 3e16e83a62edac7617bfd8dbb4e55d04ff6adbe1 ]

Correct race condition where ioaccel is re-enabled before the raid_map is updated. For RAID_1, RAID_1ADM, and RAID 5/6 there is a BUG_ON called which is bad.

- Change event thread to disable ioaccel only. Send all requests down the RAID path instead.

- Have rescan thread handle offload_enable.

- Since there is only one rescan allowed at a time, turning offload_enabled on/off should not be racy. Each handler queues up a rescan if one is already in progress.

- For timing diagram, offload_enabled is initially off due to a change (transformation: splitmirror/remirror), ...

otbe = offload_to_be_enabled
oe = offload_enabled

  Time Event         Rescan              Completion     Request
       Worker        Worker              Thread         Thread
  ---- ------        ------              ----------     -------
   T0   |             |                       + UA      |
   T1   |             + rescan started        | 0x3f    |
   T2   + Event       |                       | 0x0e    |
   T3   + Ack msg     |                       |         |
   T4   |             + if (!dev[i]->oe &&    |         |
   T5   |             |     dev[i]->otbe)     |         |
   T6   |             |      get_raid_map     |         |
   T7   + otbe = 1    |                       |         |
   T8   |             |                       |         |
   T9   |             + oe = otbe             |         |
   T10  |             |                       |         + ioaccel request
   T11                                                  * BUG_ON

T0 - I/O completion with UA 0x3f 0x0e sets rescan flag. T1 - rescan worker thread starts a rescan.
T2 - event comes in
T3 - event thread starts and issues "Acknowledge" message
...
T6 - rescan thread has bypassed code to reload new raid map.
...
T7 - event thread runs and sets offload_to_be_enabled
...
T9 - rescan thread turns on offload_enabled.
T10- request comes in and goes down ioaccel path. T11- BUG_ON.

- After the patch is applied, ioaccel_enabled can only be re-enabled in the re-scan thread.

---
 drivers/scsi/hpsa.c | 80 ++++++++++++++++++++++++++++++++-------------
 1 file changed, 57 insertions(+), 23 deletions(-)
drivers/scsi/hpsa.c +57 -23
index f570b8c5d857c..11de2198bb87d 100644
@@ -507,6 +507,12 @@ static ssize_t host_store_rescan(struct device *dev,
 	return count;
 }
 
+static void hpsa_turn_off_ioaccel_for_device(struct hpsa_scsi_dev_t *device)
+{
+	device->offload_enabled = 0;
+	device->offload_to_be_enabled = 0;
+}
+
 static ssize_t host_show_firmware_revision(struct device *dev,
 	     struct device_attribute *attr, char *buf)
 {
@@ -1743,8 +1749,7 @@ static void hpsa_figure_phys_disk_ptrs(struct ctlr_info *h,
 				__func__,
 				h->scsi_host->host_no, logical_drive->bus,
 				logical_drive->target, logical_drive->lun);
-			logical_drive->offload_enabled = 0;
-			logical_drive->offload_to_be_enabled = 0;
+			hpsa_turn_off_ioaccel_for_device(logical_drive);
 			logical_drive->queue_depth = 8;
 		}
 	}
@@ -2496,8 +2501,7 @@ static void process_ioaccel2_completion(struct ctlr_info *h,
 			IOACCEL2_SERV_RESPONSE_FAILURE) {
 		if (c2->error_data.status ==
 			IOACCEL2_STATUS_SR_IOACCEL_DISABLED) {
-			dev->offload_enabled = 0;
-			dev->offload_to_be_enabled = 0;
+			hpsa_turn_off_ioaccel_for_device(dev);
 		}
 
 		return hpsa_retry_cmd(h, c);
@@ -3676,10 +3680,17 @@ static void hpsa_get_ioaccel_status(struct ctlr_info *h,
 	this_device->offload_config =
 		!!(ioaccel_status & OFFLOAD_CONFIGURED_BIT);
 	if (this_device->offload_config) {
-		this_device->offload_to_be_enabled =
+		bool offload_enabled =
 			!!(ioaccel_status & OFFLOAD_ENABLED_BIT);
-		if (hpsa_get_raid_map(h, scsi3addr, this_device))
-			this_device->offload_to_be_enabled = 0;
+		/*
+		 * Check to see if offload can be enabled.
+		 */
+		if (offload_enabled) {
+			rc = hpsa_get_raid_map(h, scsi3addr, this_device);
+			if (rc) /* could not load raid_map */
+				goto out;
+			this_device->offload_to_be_enabled = 1;
+		}
 	}
 
 out:
@@ -3998,8 +4009,7 @@ static int hpsa_update_device_info(struct ctlr_info *h,
 	} else {
 		this_device->raid_level = RAID_UNKNOWN;
 		this_device->offload_config = 0;
-		this_device->offload_enabled = 0;
-		this_device->offload_to_be_enabled = 0;
+		hpsa_turn_off_ioaccel_for_device(this_device);
 		this_device->hba_ioaccel_enabled = 0;
 		this_device->volume_offline = 0;
 		this_device->queue_depth = h->nr_cmds;
@@ -5213,8 +5223,12 @@ static int hpsa_scsi_ioaccel_raid_map(struct ctlr_info *h,
 		/* Handles load balance across RAID 1 members.
 		 * (2-drive R1 and R10 with even # of drives.)
 		 * Appropriate for SSDs, not optimal for HDDs
+		 * Ensure we have the correct raid_map.
 		 */
-		BUG_ON(le16_to_cpu(map->layout_map_count) != 2);
+		if (le16_to_cpu(map->layout_map_count) != 2) {
+			hpsa_turn_off_ioaccel_for_device(dev);
+			return IO_ACCEL_INELIGIBLE;
+		}
 		if (dev->offload_to_mirror)
 			map_index += le16_to_cpu(map->data_disks_per_row);
 		dev->offload_to_mirror = !dev->offload_to_mirror;
@@ -5222,8 +5236,12 @@ static int hpsa_scsi_ioaccel_raid_map(struct ctlr_info *h,
 	case HPSA_RAID_ADM:
 		/* Handles N-way mirrors  (R1-ADM)
 		 * and R10 with # of drives divisible by 3.)
+		 * Ensure we have the correct raid_map.
 		 */
-		BUG_ON(le16_to_cpu(map->layout_map_count) != 3);
+		if (le16_to_cpu(map->layout_map_count) != 3) {
+			hpsa_turn_off_ioaccel_for_device(dev);
+			return IO_ACCEL_INELIGIBLE;
+		}
 
 		offload_to_mirror = dev->offload_to_mirror;
 		raid_map_helper(map, offload_to_mirror,
@@ -5248,7 +5266,10 @@ static int hpsa_scsi_ioaccel_raid_map(struct ctlr_info *h,
 		r5or6_blocks_per_row =
 			le16_to_cpu(map->strip_size) *
 			le16_to_cpu(map->data_disks_per_row);
-		BUG_ON(r5or6_blocks_per_row == 0);
+		if (r5or6_blocks_per_row == 0) {
+			hpsa_turn_off_ioaccel_for_device(dev);
+			return IO_ACCEL_INELIGIBLE;
+		}
 		stripesize = r5or6_blocks_per_row *
 			le16_to_cpu(map->layout_map_count);
 #if BITS_PER_LONG == 32
@@ -8218,7 +8239,7 @@ static int detect_controller_lockup(struct ctlr_info *h)
  *
  * Called from monitor controller worker (hpsa_event_monitor_worker)
  *
- * A Volume (or Volumes that comprise an Array set may be undergoing a
+ * A Volume (or Volumes that comprise an Array set) may be undergoing a
  * transformation, so we will be turning off ioaccel for all volumes that
  * make up the Array.
  */
@@ -8241,6 +8262,9 @@ static void hpsa_set_ioaccel_status(struct ctlr_info *h)
 	 * Run through current device list used during I/O requests.
 	 */
 	for (i = 0; i < h->ndevices; i++) {
+		int offload_to_be_enabled = 0;
+		int offload_config = 0;
+
 		device = h->dev[i];
 
 		if (!device)
@@ -8258,25 +8282,35 @@ static void hpsa_set_ioaccel_status(struct ctlr_info *h)
 			continue;
 
 		ioaccel_status = buf[IOACCEL_STATUS_BYTE];
-		device->offload_config =
+
+		/*
+		 * Check if offload is still configured on
+		 */
+		offload_config =
 				!!(ioaccel_status & OFFLOAD_CONFIGURED_BIT);
-		if (device->offload_config)
-			device->offload_to_be_enabled =
+		/*
+		 * If offload is configured on, check to see if ioaccel
+		 * needs to be enabled.
+		 */
+		if (offload_config)
+			offload_to_be_enabled =
 				!!(ioaccel_status & OFFLOAD_ENABLED_BIT);
 
+		/*
+		 * If ioaccel is to be re-enabled, re-enable later during the
+		 * scan operation so the driver can get a fresh raidmap
+		 * before turning ioaccel back on.
+		 */
+		if (offload_to_be_enabled)
+			continue;
+
 		/*
 		 * Immediately turn off ioaccel for any volume the
 		 * controller tells us to. Some of the reasons could be:
 		 *    transformation - change to the LVs of an Array.
 		 *    degraded volume - component failure
-		 *
-		 * If ioaccel is to be re-enabled, re-enable later during the
-		 * scan operation so the driver can get a fresh raidmap
-		 * before turning ioaccel back on.
-		 *
 		 */
-		if (!device->offload_to_be_enabled)
-			device->offload_enabled = 0;
+		hpsa_turn_off_ioaccel_for_device(device);
 	}
 
 	kfree(buf);
Signature · 1 line
2.25.1
author maintainer
#126 lore raw

PATCH 125/206 tools: gpio-hammer: Avoid potential overflow in main

In reply to Sasha Levin

From: Gabriel Ravier <[email protected]>

[ Upstream commit d1ee7e1f5c9191afb69ce46cc7752e4257340a31 ]

If '-o' was used more than 64 times in a single invocation of gpio-hammer, this could lead to an overflow of the 'lines' array. This commit fixes this by avoiding the overflow and giving a proper diagnostic back to the user

---
 tools/gpio/gpio-hammer.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)
tools/gpio/gpio-hammer.c +16 -1
index 4bcb234c0fcab..3da5462a0c7d3 100644
@@ -138,7 +138,14 @@ int main(int argc, char **argv)
 			device_name = optarg;
 			break;
 		case 'o':
-			lines[i] = strtoul(optarg, NULL, 10);
+			/*
+			 * Avoid overflow. Do not immediately error, we want to
+			 * be able to accurately report on the amount of times
+			 * '-o' was given to give an accurate error message
+			 */
+			if (i < GPIOHANDLES_MAX)
+				lines[i] = strtoul(optarg, NULL, 10);
+
 			i++;
 			break;
 		case '?':
@@ -146,6 +153,14 @@ int main(int argc, char **argv)
 			return -1;
 		}
 	}
+
+	if (i >= GPIOHANDLES_MAX) {
+		fprintf(stderr,
+			"Only %d occurences of '-o' are allowed, %d were found\n",
+			GPIOHANDLES_MAX, i + 1);
+		return -1;
+	}
+
 	nlines = i;
 
 	if (!device_name || !nlines) {
Signature · 1 line
2.25.1
author maintainer
#125 lore raw

PATCH 124/206 cpufreq: powernv: Fix frame-size-overflow in powernv_cpufreq_work_fn

In reply to Sasha Levin

From: Pratik Rajesh Sampat <[email protected]>

[ Upstream commit d95fe371ecd28901f11256c610b988ed44e36ee2 ]

The patch avoids allocating cpufreq_policy on stack hence fixing frame size overflow in 'powernv_cpufreq_work_fn'

Fixes 227942809b52 ("cpufreq: powernv: Restore cpu frequency to policy->cur on unthrottling")
---
 drivers/cpufreq/powernv-cpufreq.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)
drivers/cpufreq/powernv-cpufreq.c +8 -5
index 687c92ef76440..79942f7057576 100644
@@ -903,6 +903,7 @@ static struct notifier_block powernv_cpufreq_reboot_nb = {
 void powernv_cpufreq_work_fn(struct work_struct *work)
 {
 	struct chip *chip = container_of(work, struct chip, throttle);
+	struct cpufreq_policy *policy;
 	unsigned int cpu;
 	cpumask_t mask;
 
@@ -917,12 +918,14 @@ void powernv_cpufreq_work_fn(struct work_struct *work)
 	chip->restore = false;
 	for_each_cpu(cpu, &mask) {
 		int index;
-		struct cpufreq_policy policy;
 
-		cpufreq_get_policy(&policy, cpu);
-		index = cpufreq_table_find_index_c(&policy, policy.cur);
-		powernv_cpufreq_target_index(&policy, index);
-		cpumask_andnot(&mask, &mask, policy.cpus);
+		policy = cpufreq_cpu_get(cpu);
+		if (!policy)
+			continue;
+		index = cpufreq_table_find_index_c(policy, policy->cur);
+		powernv_cpufreq_target_index(policy, index);
+		cpumask_andnot(&mask, &mask, policy->cpus);
+		cpufreq_cpu_put(policy);
 	}
 out:
 	put_online_cpus();
Signature · 1 line
2.25.1
author maintainer
#122 lore raw

PATCH 121/206 serial: 8250_omap: Fix sleeping function called from invalid context during probe

In reply to Sasha Levin

From: Peter Ujfalusi <[email protected]>

[ Upstream commit 4ce35a3617c0ac758c61122b2218b6c8c9ac9398 ]

When booting j721e the following bug is printed:

[    1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
[    1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1
[    1.154832] 3 locks held by kworker/0:1/12:
[    1.154836]  #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154852]  #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154860]  #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138
[    1.154872] irq event stamp: 63096
[    1.154881] hardirqs last  enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78
[    1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80
[    1.154893] softirqs last  enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564
[    1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140
[    1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221
[    1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT)
[    1.154917] Workqueue: events deferred_probe_work_func
[    1.154923] Call trace:
[    1.154928]  dump_backtrace+0x0/0x190
[    1.154933]  show_stack+0x14/0x20
[    1.154940]  dump_stack+0xe0/0x148
[    1.154946]  ___might_sleep+0x150/0x1f0
[    1.154952]  __might_sleep+0x4c/0x80
[    1.154957]  wait_for_completion_timeout+0x40/0x140
[    1.154964]  ti_sci_set_device_state+0xa0/0x158
[    1.154969]  ti_sci_cmd_get_device_exclusive+0x14/0x20
[    1.154977]  ti_sci_dev_start+0x34/0x50
[    1.154984]  genpd_runtime_resume+0x78/0x1f8
[    1.154991]  __rpm_callback+0x3c/0x140
[    1.154996]  rpm_callback+0x20/0x80
[    1.155001]  rpm_resume+0x568/0x758
[    1.155007]  __pm_runtime_resume+0x44/0xb0
[    1.155013]  omap8250_probe+0x2b4/0x508
[    1.155019]  platform_drv_probe+0x50/0xa0
[    1.155023]  really_probe+0xd4/0x318
[    1.155028]  driver_probe_device+0x54/0xe8
[    1.155033]  __device_attach_driver+0x80/0xb8
[    1.155039]  bus_for_each_drv+0x74/0xc0
[    1.155044]  __device_attach+0xdc/0x138
[    1.155049]  device_initial_probe+0x10/0x18
[    1.155053]  bus_probe_device+0x98/0xa0
[    1.155058]  deferred_probe_work_func+0x74/0xb0
[    1.155063]  process_one_work+0x280/0x6e8
[    1.155068]  worker_thread+0x48/0x430
[    1.155073]  kthread+0x108/0x138
[    1.155079]  ret_from_fork+0x10/0x18

To fix the bug we need to first call pm_runtime_enable() prior to any pm_runtime calls.

---
 drivers/tty/serial/8250/8250_omap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/tty/serial/8250/8250_omap.c +1 -1
index a019286f8bb65..a7e555e413a69 100644
@@ -1227,11 +1227,11 @@ static int omap8250_probe(struct platform_device *pdev)
 	spin_lock_init(&priv->rx_dma_lock);
 
 	device_init_wakeup(&pdev->dev, true);
+	pm_runtime_enable(&pdev->dev);
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, -1);
 
 	pm_runtime_irq_safe(&pdev->dev);
-	pm_runtime_enable(&pdev->dev);
 
 	pm_runtime_get_sync(&pdev->dev);
 
Signature · 1 line
2.25.1
author maintainer
#120 lore raw

PATCH 119/206 perf parse-events: Fix 3 use after frees found with clang ASAN

In reply to Sasha Levin

From: Ian Rogers <[email protected]>

[ Upstream commit d4953f7ef1a2e87ef732823af35361404d13fea8 ]

Reproducible with a clang asan build and then running perf test in particular 'Parse event definition strings'.

---
 tools/perf/util/evsel.c        | 1 +
 tools/perf/util/parse-events.c | 4 ++--
 2 files changed, 3 insertions(+), 2 deletions(-)
tools/perf/util/evsel.c +1 -0
index 4fad92213609f..68c5ab0e1800b 100644
@@ -1290,6 +1290,7 @@ void perf_evsel__exit(struct perf_evsel *evsel)
 	thread_map__put(evsel->threads);
 	zfree(&evsel->group_name);
 	zfree(&evsel->name);
+	zfree(&evsel->pmu_name);
 	perf_evsel__object.fini(evsel);
 }
 
tools/perf/util/parse-events.c +2 -2
index 95043cae57740..6d087d9acd5ee 100644
@@ -1261,7 +1261,7 @@ int parse_events_add_pmu(struct parse_events_state *parse_state,
 		attr.type = pmu->type;
 		evsel = __add_event(list, &parse_state->idx, &attr, NULL, pmu, NULL, auto_merge_stats);
 		if (evsel) {
-			evsel->pmu_name = name;
+			evsel->pmu_name = name ? strdup(name) : NULL;
 			evsel->use_uncore_alias = use_uncore_alias;
 			return 0;
 		} else {
@@ -1302,7 +1302,7 @@ int parse_events_add_pmu(struct parse_events_state *parse_state,
 		evsel->snapshot = info.snapshot;
 		evsel->metric_expr = info.metric_expr;
 		evsel->metric_name = info.metric_name;
-		evsel->pmu_name = name;
+		evsel->pmu_name = name ? strdup(name) : NULL;
 		evsel->use_uncore_alias = use_uncore_alias;
 	}
 
Signature · 1 line
2.25.1
author maintainer
#121 lore raw

PATCH 120/206 serial: 8250_port: Don't service RX FIFO if throttled

In reply to Sasha Levin

From: Vignesh Raghavendra <[email protected]>

[ Upstream commit f19c3f6c8109b8bab000afd35580929958e087a9 ]

When port's throttle callback is called, it should stop pushing any more data into TTY buffer to avoid buffer overflow. This means driver has to stop HW from receiving more data and assert the HW flow control. For UARTs with auto HW flow control (such as 8250_omap) manual assertion of flow control line is not possible and only way is to allow RX FIFO to fill up, thus trigger auto HW flow control logic.

Therefore make sure that 8250 generic IRQ handler does not drain data when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not servicing, RX FIFO would trigger auto HW flow control when FIFO occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading the register, data has to be drained in case there are FIFO errors, else error information will lost.

---
 drivers/tty/serial/8250/8250_port.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)
drivers/tty/serial/8250/8250_port.c +15 -1
index 09f0dc3b967b1..60ca19eca1f63 100644
@@ -1861,6 +1861,7 @@ int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
 	unsigned char status;
 	unsigned long flags;
 	struct uart_8250_port *up = up_to_u8250p(port);
+	bool skip_rx = false;
 
 	if (iir & UART_IIR_NO_INT)
 		return 0;
@@ -1869,7 +1870,20 @@ int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
 
 	status = serial_port_in(port, UART_LSR);
 
-	if (status & (UART_LSR_DR | UART_LSR_BI)) {
+	/*
+	 * If port is stopped and there are no error conditions in the
+	 * FIFO, then don't drain the FIFO, as this may lead to TTY buffer
+	 * overflow. Not servicing, RX FIFO would trigger auto HW flow
+	 * control when FIFO occupancy reaches preset threshold, thus
+	 * halting RX. This only works when auto HW flow control is
+	 * available.
+	 */
+	if (!(status & (UART_LSR_FIFOE | UART_LSR_BRK_ERROR_BITS)) &&
+	    (port->status & (UPSTAT_AUTOCTS | UPSTAT_AUTORTS)) &&
+	    !(port->read_status_mask & UART_LSR_DR))
+		skip_rx = true;
+
+	if (status & (UART_LSR_DR | UART_LSR_BI) && !skip_rx) {
 		if (!up->dma || handle_rx_dma(up, iir))
 			status = serial8250_rx_chars(up, status);
 	}
Signature · 1 line
2.25.1
author maintainer
#118 lore raw

PATCH 117/206 tracing: Use address-of operator on section symbols

In reply to Sasha Levin

From: Nathan Chancellor <[email protected]>

[ Upstream commit bf2cbe044da275021b2de5917240411a19e5c50d ]

Clang warns:

../kernel/trace/trace.c:9335:33: warning: array comparison always evaluates to true [-Wtautological-compare]

        if (__stop___trace_bprintk_fmt != __start___trace_bprintk_fmt)
                                       ^

1 warning generated.

These are not true arrays, they are linker defined symbols, which are just addresses. Using the address of operator silences the warning and does not change the runtime result of the check (tested with some print statements compiled in with clang + ld.lld and gcc + ld.bfd in QEMU).

---
 kernel/trace/trace.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/trace/trace.c +1 -1
index 17505a22d800b..6bf617ff03694 100644
@@ -8529,7 +8529,7 @@ __init static int tracer_alloc_buffers(void)
 		goto out_free_buffer_mask;
 
 	/* Only allocate trace_printk buffers if a trace_printk exists */
-	if (__stop___trace_bprintk_fmt != __start___trace_bprintk_fmt)
+	if (&__stop___trace_bprintk_fmt != &__start___trace_bprintk_fmt)
 		/* Must be called before global_trace.buffer is allocated */
 		trace_printk_init_buffers();
 
Signature · 1 line
2.25.1
author maintainer
#108 lore raw

PATCH 107/206 xfs: mark dir corrupt when lookup-by-hash fails

In reply to Sasha Levin

From: "Darrick J. Wong" <[email protected]>

[ Upstream commit 2e107cf869eecc770e3f630060bb4e5f547d0fd8 ]

In xchk_dir_actor, we attempt to validate the directory hash structures by performing a directory entry lookup by (hashed) name. If the lookup returns ENOENT, that means that the hash information is corrupt. The _process_error functions don't catch this, so we have to add that explicitly.

---
 fs/xfs/scrub/dir.c | 3 +++
 1 file changed, 3 insertions(+)
fs/xfs/scrub/dir.c +3 -0
index cd3e4d768a18c..33dfcba72c7a0 100644
@@ -156,6 +156,9 @@ xchk_dir_actor(
 	xname.type = XFS_DIR3_FT_UNKNOWN;
 
 	error = xfs_dir_lookup(sdc->sc->tp, ip, &xname, &lookup_ino, NULL);
+	/* ENOENT means the hash lookup failed and the dir is corrupt */
+	if (error == -ENOENT)
+		error = -EFSCORRUPTED;
 	if (!xchk_fblock_process_error(sdc->sc, XFS_DATA_FORK, offset,
 			&error))
 		goto out;
Signature · 1 line
2.25.1
author maintainer
#110 lore raw

PATCH 109/206 tpm: ibmvtpm: Wait for buffer to be set before proceeding

In reply to Sasha Levin

From: Stefan Berger <[email protected]>

[ Upstream commit d8d74ea3c00214aee1e1826ca18e77944812b9b4 ]

Synchronize with the results from the CRQs before continuing with the initialization. This avoids trying to send TPM commands while the rtce buffer has not been allocated, yet.

This patch fixes an existing race condition that may occurr if the hypervisor does not quickly respond to the VTPM_GET_RTCE_BUFFER_SIZE request sent during initialization and therefore the ibmvtpm->rtce_buf has not been allocated at the time the first TPM command is sent.

Fixes 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
---
 drivers/char/tpm/tpm_ibmvtpm.c | 9 +++++++++
 drivers/char/tpm/tpm_ibmvtpm.h | 1 +
 2 files changed, 10 insertions(+)
drivers/char/tpm/tpm_ibmvtpm.c +9 -0
index 569e93e1f06cc..3ba67bc6baba0 100644
@@ -588,6 +588,7 @@ static irqreturn_t ibmvtpm_interrupt(int irq, void *vtpm_instance)
 	 */
 	while ((crq = ibmvtpm_crq_get_next(ibmvtpm)) != NULL) {
 		ibmvtpm_crq_process(crq, ibmvtpm);
+		wake_up_interruptible(&ibmvtpm->crq_queue.wq);
 		crq->valid = 0;
 		smp_wmb();
 	}
@@ -635,6 +636,7 @@ static int tpm_ibmvtpm_probe(struct vio_dev *vio_dev,
 	}
 
 	crq_q->num_entry = CRQ_RES_BUF_SIZE / sizeof(*crq_q->crq_addr);
+	init_waitqueue_head(&crq_q->wq);
 	ibmvtpm->crq_dma_handle = dma_map_single(dev, crq_q->crq_addr,
 						 CRQ_RES_BUF_SIZE,
 						 DMA_BIDIRECTIONAL);
@@ -687,6 +689,13 @@ static int tpm_ibmvtpm_probe(struct vio_dev *vio_dev,
 	if (rc)
 		goto init_irq_cleanup;
 
+	if (!wait_event_timeout(ibmvtpm->crq_queue.wq,
+				ibmvtpm->rtce_buf != NULL,
+				HZ)) {
+		dev_err(dev, "CRQ response timed out\n");
+		goto init_irq_cleanup;
+	}
+
 	return tpm_chip_register(chip);
 init_irq_cleanup:
 	do {
drivers/char/tpm/tpm_ibmvtpm.h +1 -0
index 91dfe766d0800..4f6a124601db4 100644
@@ -31,6 +31,7 @@ struct ibmvtpm_crq_queue {
 	struct ibmvtpm_crq *crq_addr;
 	u32 index;
 	u32 num_entry;
+	wait_queue_head_t wq;
 };
 
 struct ibmvtpm_dev {
Signature · 1 line
2.25.1
author maintainer
#105 lore raw

PATCH 104/206 Bluetooth: L2CAP: handle l2cap config request during open state

In reply to Sasha Levin

From: Howard Chung <[email protected]>

[ Upstream commit 96298f640104e4cd9a913a6e50b0b981829b94ff ]

According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5, the incoming L2CAP_ConfigReq should be handled during OPEN state.

The section below shows the btmon trace when running L2CAP/COS/CFD/BV-12-C before and after this change.

=== Before ===
...

Quoted 1 line

ACL Data RX: Handle 256 flags 0x02 dlen 12 #22

      L2CAP: Connection Request (0x02) ident 2 len 4
        PSM: 1 (0x0001)
        Source CID: 65
< ACL Data TX: Handle 256 flags 0x00 dlen 16                #23
      L2CAP: Connection Response (0x03) ident 2 len 8
        Destination CID: 64
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 256 flags 0x00 dlen 12                #24
      L2CAP: Configure Request (0x04) ident 2 len 4
        Destination CID: 65
        Flags: 0x0000
Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #25

Num handles: 1
Handle: 256
Count: 1

Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #26

Num handles: 1
Handle: 256
Count: 1

Quoted 1 line

ACL Data RX: Handle 256 flags 0x02 dlen 16 #27

      L2CAP: Configure Request (0x04) ident 3 len 8
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00                                            ..
< ACL Data TX: Handle 256 flags 0x00 dlen 18                #28
      L2CAP: Configure Response (0x05) ident 3 len 10
        Source CID: 65
        Flags: 0x0000
        Result: Success (0x0000)
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 672
Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #29

Num handles: 1
Handle: 256
Count: 1

Quoted 1 line

ACL Data RX: Handle 256 flags 0x02 dlen 14 #30

      L2CAP: Configure Response (0x05) ident 2 len 6
        Source CID: 64
        Flags: 0x0000
        Result: Success (0x0000)
Quoted 1 line

ACL Data RX: Handle 256 flags 0x02 dlen 20 #31

      L2CAP: Configure Request (0x04) ident 3 len 12
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00 91 02 11 11                                ......

< ACL Data TX: Handle 256 flags 0x00 dlen 14 #32
L2CAP: Command Reject (0x01) ident 3 len 6
Reason: Invalid CID in request (0x0002) Destination CID: 64
Source CID: 65

Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #33

Num handles: 1
Handle: 256
Count: 1
...
=== After ===
...

Quoted 1 line

ACL Data RX: Handle 256 flags 0x02 dlen 12 #22

      L2CAP: Connection Request (0x02) ident 2 len 4
        PSM: 1 (0x0001)
        Source CID: 65
< ACL Data TX: Handle 256 flags 0x00 dlen 16               #23
      L2CAP: Connection Response (0x03) ident 2 len 8
        Destination CID: 64
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 256 flags 0x00 dlen 12               #24
      L2CAP: Configure Request (0x04) ident 2 len 4
        Destination CID: 65
        Flags: 0x0000
Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #25

Num handles: 1
Handle: 256
Count: 1

Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #26

Num handles: 1
Handle: 256
Count: 1

Quoted 1 line

ACL Data RX: Handle 256 flags 0x02 dlen 16 #27

      L2CAP: Configure Request (0x04) ident 3 len 8
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00                                            ..
< ACL Data TX: Handle 256 flags 0x00 dlen 18               #28
      L2CAP: Configure Response (0x05) ident 3 len 10
        Source CID: 65
        Flags: 0x0000
        Result: Success (0x0000)
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 672
Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #29

Num handles: 1
Handle: 256
Count: 1

Quoted 1 line

ACL Data RX: Handle 256 flags 0x02 dlen 14 #30

      L2CAP: Configure Response (0x05) ident 2 len 6
        Source CID: 64
        Flags: 0x0000
        Result: Success (0x0000)
Quoted 1 line

ACL Data RX: Handle 256 flags 0x02 dlen 20 #31

      L2CAP: Configure Request (0x04) ident 3 len 12
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00 91 02 11 11                                .....
< ACL Data TX: Handle 256 flags 0x00 dlen 18               #32
      L2CAP: Configure Response (0x05) ident 3 len 10
        Source CID: 65
        Flags: 0x0000
        Result: Success (0x0000)
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 672
< ACL Data TX: Handle 256 flags 0x00 dlen 12               #33
      L2CAP: Configure Request (0x04) ident 3 len 4
        Destination CID: 65
        Flags: 0x0000
Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #34

Num handles: 1
Handle: 256
Count: 1

Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #35

Num handles: 1
Handle: 256
Count: 1
...

---
 net/bluetooth/l2cap_core.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
net/bluetooth/l2cap_core.c +2 -1
index b1f51cb007ea6..c04107d446016 100644
@@ -4117,7 +4117,8 @@ static inline int l2cap_config_req(struct l2cap_conn *conn,
 		return 0;
 	}
 
-	if (chan->state != BT_CONFIG && chan->state != BT_CONNECT2) {
+	if (chan->state != BT_CONFIG && chan->state != BT_CONNECT2 &&
+	    chan->state != BT_CONNECTED) {
 		cmd_reject_invalid_cid(conn, cmd->ident, chan->scid,
 				       chan->dcid);
 		goto unlock;
Signature · 1 line
2.25.1
author maintainer
#106 lore raw

PATCH 105/206 media: tda10071: fix unsigned sign extension overflow

In reply to Sasha Levin

From: Colin Ian King <[email protected]>

[ Upstream commit a7463e2dc698075132de9905b89f495df888bb79 ]

The shifting of buf[3] by 24 bits to the left will be promoted to a 32 bit signed int and then sign-extended to an unsigned long. In the unlikely event that the the top bit of buf[3] is set then all then all the upper bits end up as also being set because of the sign-extension and this affect the ev->post_bit_error sum. Fix this by using the temporary u32 variable bit_error to avoid the sign-extension promotion. This also removes the need to do the computation twice.

Addresses-Coverity: ("Unintended sign extension")

Fixes 267897a4708f ("[media] tda10071: implement DVBv5 statistics")
---
 drivers/media/dvb-frontends/tda10071.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/media/dvb-frontends/tda10071.c +5 -4
index 097c42d3f8c26..df0c7243eafe4 100644
@@ -483,10 +483,11 @@ static int tda10071_read_status(struct dvb_frontend *fe, enum fe_status *status)
 			goto error;
 
 		if (dev->delivery_system == SYS_DVBS) {
-			dev->dvbv3_ber = buf[0] << 24 | buf[1] << 16 |
-					 buf[2] << 8 | buf[3] << 0;
-			dev->post_bit_error += buf[0] << 24 | buf[1] << 16 |
-					       buf[2] << 8 | buf[3] << 0;
+			u32 bit_error = buf[0] << 24 | buf[1] << 16 |
+					buf[2] << 8 | buf[3] << 0;
+
+			dev->dvbv3_ber = bit_error;
+			dev->post_bit_error += bit_error;
 			c->post_bit_error.stat[0].scale = FE_SCALE_COUNTER;
 			c->post_bit_error.stat[0].uvalue = dev->post_bit_error;
 			dev->block_error += buf[4] << 8 | buf[5] << 0;
Signature · 1 line
2.25.1
author maintainer
#109 lore raw

PATCH 108/206 ext4: mark block bitmap corrupted when found instead of BUGON

In reply to Sasha Levin

From: Dmitry Monakhov <[email protected]>

[ Upstream commit eb5760863fc28feab28b567ddcda7e667e638da0 ]

We already has similar code in ext4_mb_complex_scan_group(), but ext4_mb_simple_scan_group() still affected.

Other reports: https://www.spinics.net/lists/linux-ext4/msg60231.html

---
 fs/ext4/mballoc.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
fs/ext4/mballoc.c +9 -2
index 8dd54a8a03610..054cfdd007d69 100644
@@ -1901,8 +1901,15 @@ void ext4_mb_simple_scan_group(struct ext4_allocation_context *ac,
 		BUG_ON(buddy == NULL);
 
 		k = mb_find_next_zero_bit(buddy, max, 0);
-		BUG_ON(k >= max);
-
+		if (k >= max) {
+			ext4_grp_locked_error(ac->ac_sb, e4b->bd_group, 0, 0,
+				"%d free clusters of order %d. But found 0",
+				grp->bb_counters[i], i);
+			ext4_mark_group_bitmap_corrupted(ac->ac_sb,
+					 e4b->bd_group,
+					EXT4_GROUP_INFO_BBITMAP_CORRUPT);
+			break;
+		}
 		ac->ac_found++;
 
 		ac->ac_b_ex.fe_len = 1 << i;
Signature · 1 line
2.25.1
author maintainer
#112 lore raw

PATCH 111/206 rtc: ds1374: fix possible race condition

In reply to Sasha Levin

From: Alexandre Belloni <[email protected]>

[ Upstream commit c11af8131a4e7ba1960faed731ee7e84c2c13c94 ]

The RTC IRQ is requested before the struct rtc_device is allocated, this may lead to a NULL pointer dereference in the IRQ handler.

To fix this issue, allocating the rtc_device struct before requesting the RTC IRQ using devm_rtc_allocate_device, and use rtc_register_device to register the RTC device.

---
 drivers/rtc/rtc-ds1374.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)
drivers/rtc/rtc-ds1374.c +9 -6
index 38a2e9e684df4..77a106e90124b 100644
@@ -620,6 +620,10 @@ static int ds1374_probe(struct i2c_client *client,
 	if (!ds1374)
 		return -ENOMEM;
 
+	ds1374->rtc = devm_rtc_allocate_device(&client->dev);
+	if (IS_ERR(ds1374->rtc))
+		return PTR_ERR(ds1374->rtc);
+
 	ds1374->client = client;
 	i2c_set_clientdata(client, ds1374);
 
@@ -641,12 +645,11 @@ static int ds1374_probe(struct i2c_client *client,
 		device_set_wakeup_capable(&client->dev, 1);
 	}
 
-	ds1374->rtc = devm_rtc_device_register(&client->dev, client->name,
-						&ds1374_rtc_ops, THIS_MODULE);
-	if (IS_ERR(ds1374->rtc)) {
-		dev_err(&client->dev, "unable to register the class device\n");
-		return PTR_ERR(ds1374->rtc);
-	}
+	ds1374->rtc->ops = &ds1374_rtc_ops;
+
+	ret = rtc_register_device(ds1374->rtc);
+	if (ret)
+		return ret;
 
 #ifdef CONFIG_RTC_DRV_DS1374_WDT
 	save_client = client;
Signature · 1 line
2.25.1
author maintainer
#107 lore raw

PATCH 106/206 xfs: don't ever return a stale pointer from __xfs_dir3_free_read

In reply to Sasha Levin

From: "Darrick J. Wong" <[email protected]>

[ Upstream commit 1cb5deb5bc095c070c09a4540c45f9c9ba24be43 ]

If we decide that a directory free block is corrupt, we must take care not to leak a buffer pointer to the caller. After xfs_trans_brelse returns, the buffer can be freed or reused, which means that we have to set *bpp back to NULL.

Callers are supposed to notice the nonzero return value and not use the buffer pointer, but we should code more defensively, even if all current callers handle this situation correctly.

Fixes de14c5f541e7 ("xfs: verify free block header fields")
---
 fs/xfs/libxfs/xfs_dir2_node.c | 1 +
 1 file changed, 1 insertion(+)
fs/xfs/libxfs/xfs_dir2_node.c +1 -0
index f1bb3434f51c7..01e99806b941f 100644
@@ -214,6 +214,7 @@ __xfs_dir3_free_read(
 	if (fa) {
 		xfs_verifier_error(*bpp, -EFSCORRUPTED, fa);
 		xfs_trans_brelse(tp, *bpp);
+		*bpp = NULL;
 		return -EFSCORRUPTED;
 	}
 
Signature · 1 line
2.25.1
author maintainer
#111 lore raw

PATCH 110/206 rtc: sa1100: fix possible race condition

In reply to Sasha Levin

From: Alexandre Belloni <[email protected]>

[ Upstream commit f2997775b111c6d660c32a18d5d44d37cb7361b1 ]

Both RTC IRQs are requested before the struct rtc_device is allocated, this may lead to a NULL pointer dereference in the IRQ handler.

To fix this issue, allocating the rtc_device struct before requesting the IRQs using devm_rtc_allocate_device, and use rtc_register_device to register the RTC device.

---
 drivers/rtc/rtc-sa1100.c | 18 ++++++++++--------
 1 file changed, 10 insertions(+), 8 deletions(-)
drivers/rtc/rtc-sa1100.c +10 -8
index 304d905cb23fd..56f625371735f 100644
@@ -186,7 +186,6 @@ static const struct rtc_class_ops sa1100_rtc_ops = {
 
 int sa1100_rtc_init(struct platform_device *pdev, struct sa1100_rtc *info)
 {
-	struct rtc_device *rtc;
 	int ret;
 
 	spin_lock_init(&info->lock);
@@ -215,15 +214,14 @@ int sa1100_rtc_init(struct platform_device *pdev, struct sa1100_rtc *info)
 		writel_relaxed(0, info->rcnr);
 	}
 
-	rtc = devm_rtc_device_register(&pdev->dev, pdev->name, &sa1100_rtc_ops,
-					THIS_MODULE);
-	if (IS_ERR(rtc)) {
+	info->rtc->ops = &sa1100_rtc_ops;
+	info->rtc->max_user_freq = RTC_FREQ;
+
+	ret = rtc_register_device(info->rtc);
+	if (ret) {
 		clk_disable_unprepare(info->clk);
-		return PTR_ERR(rtc);
+		return ret;
 	}
-	info->rtc = rtc;
-
-	rtc->max_user_freq = RTC_FREQ;
 
 	/* Fix for a nasty initialization problem the in SA11xx RTSR register.
 	 * See also the comments in sa1100_rtc_interrupt().
@@ -272,6 +270,10 @@ static int sa1100_rtc_probe(struct platform_device *pdev)
 	info->irq_1hz = irq_1hz;
 	info->irq_alarm = irq_alarm;
 
+	info->rtc = devm_rtc_allocate_device(&pdev->dev);
+	if (IS_ERR(info->rtc))
+		return PTR_ERR(info->rtc);
+
 	ret = devm_request_irq(&pdev->dev, irq_1hz, sa1100_rtc_interrupt, 0,
 			       "rtc 1Hz", &pdev->dev);
 	if (ret) {
Signature · 1 line
2.25.1