dt-bindings: media: imx258: add bindings for IMX258 sensor
Subsystems (4)
PATCH v4 1/4 dt-bindings: media: imx258: add bindings for IMX258 sensor
Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies.
---
Changes since v3:
1. Document also two lane setup.
Changes since v2:
1. Remove clock-frequency, add reset GPIOs, add supplies.
2. Use additionalProperties.
Changes since v1:
1. None
--- .../devicetree/bindings/media/i2c/imx258.yaml | 100 ++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 101 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/imx258.yaml
Documentation/devicetree/bindings/media/i2c/imx258.yaml new file +100 -0
@@ -0,0 +1,100 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/imx258.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX258 13 Mpixel CMOS Digital Image Sensor + +maintainers: + - Krzysztof Kozlowski <[email protected]> + +description: |- + IMX258 is a diagonal 5.867mm (Type 1/3.06) 13 Mega-pixel CMOS active pixel + type stacked image sensor with a square pixel array of size 4208 x 3120. It + is programmable through I2C interface. Image data is sent through MIPI + CSI-2. + +properties: + compatible: + const: sony,imx258 + + clocks: + description: + Clock frequency from 6 to 27 MHz. + maxItems: 1 + + reg: + maxItems: 1 + + reset-gpios: + description: |- + Reference to the GPIO connected to the XCLR pin, if any. + + vana-supply: + description: + Analog voltage (VANA) supply, 2.7 V + + vdig-supply: + description: + Digital I/O voltage (VDIG) supply, 1.2 V + + vif-supply: + description: + Interface voltage (VIF) supply, 1.8 V + + # See ../video-interfaces.txt for more details + port: + type: object + properties: + endpoint: + type: object + properties: + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + link-frequencies: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64-array + description: + Allowed data bus frequencies. + + required: + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6c { + compatible = "sony,imx258"; + reg = <0x6c>; + clocks = <&imx258_clk>; + + port { + endpoint { + remote-endpoint = <&csi1_ep>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <320000000>; + }; + }; + }; + };
MAINTAINERS +1 -0
@@ -16262,6 +16262,7 @@ M: Sakari Ailus <[email protected]> L: [email protected] S: Maintained T: git git://linuxtv.org/media_tree.git +F: Documentation/devicetree/bindings/media/i2c/imx258.yaml F: drivers/media/i2c/imx258.c SONY IMX274 SENSOR DRIVER
Signature · 1 line
2.17.1
PATCH v4 2/4 media: i2c: imx258: add support for binding via device tree
The IMX258 can be used also on embedded designs using device tree so allow the sensor to bind to a device tree node.
---
Changes since v1:
1. None
--- drivers/media/i2c/imx258.c | 7 +++++++ 1 file changed, 7 insertions(+)
drivers/media/i2c/imx258.c +7 -0
@@ -1291,11 +1291,18 @@ static const struct acpi_device_id imx258_acpi_ids[] = {MODULE_DEVICE_TABLE (acpi, imx258_acpi_ids);#endif +static const struct of_device_id imx258_dt_ids[] = { + { .compatible ="sony,imx258" }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, imx258_dt_ids); +static struct i2c_driver imx258_i2c_driver = { .driver = { .name ="imx258" , .pm = &imx258_pm_ops, .acpi_match_table =ACPI_PTR (imx258_acpi_ids), + .of_match_table = imx258_dt_ids, }, .probe_new = imx258_probe, .remove = imx258_remove,
Signature · 1 line
2.17.1
PATCH v4 3/4 media: i2c: imx258: simplify getting state container
In reply to Krzysztof KozlowskiThe pointer to 'struct v4l2_subdev' is stored in drvdata via v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev) struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer dereferences.
---
Changes since v3:
1. None
Changes since v2:
1. New patch
--- drivers/media/i2c/imx258.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/media/i2c/imx258.c +2 -4
@@ -1018,8 +1018,7 @@ static int imx258_set_stream(struct v4l2_subdev *sd, int enable)static int __maybe_unused imx258_suspend (struct device *dev) { -struct i2c_client *client =to_i2c_client (dev); -struct v4l2_subdev *sd =i2c_get_clientdata (client); +struct v4l2_subdev *sd =dev_get_drvdata (dev);struct imx258 *imx258 =to_imx258 (sd);if (imx258->streaming)
@@ -1030,8 +1029,7 @@ static int __maybe_unused imx258_suspend(struct device *dev)static int __maybe_unused imx258_resume (struct device *dev) { -struct i2c_client *client =to_i2c_client (dev); -struct v4l2_subdev *sd =i2c_get_clientdata (client); +struct v4l2_subdev *sd =dev_get_drvdata (dev);struct imx258 *imx258 =to_imx258 (sd);int ret;
Signature · 1 line
2.17.1
PATCH v4 4/4 media: i2c: imx258: get clock from device properties and enable it via runtime PM
In reply to Krzysztof KozlowskiThe IMX258 sensor driver checked in device properties for a clock-frequency property which actually does not mean that the clock is really running such frequency or is it even enabled.
Get the provided clock and check it frequency. If none is provided, fall back to old property.
Enable the clock when accessing the IMX258 registers and when streaming starts with runtime PM.
---
Changes since v3:
1. None
Changes since v2:
1. Do not try to set drvdata, wrap lines.
2. Use dev_dbg.
Changes since v1:
1. Use runtime PM for clock toggling
--- drivers/media/i2c/imx258.c | 71 +++++++++++++++++++++++++++++++++----- 1 file changed, 62 insertions(+), 9 deletions(-)
drivers/media/i2c/imx258.c +62 -9
@@ -2,6 +2,7 @@// Copyright (C) 2018 Intel Corporation #include <linux/acpi.h> +#include <linux/clk.h> #include <linux/delay.h> #include <linux/i2c.h> #include <linux/module.h>
@@ -68,6 +69,9 @@#define REG_CONFIG_MIRROR_FLIP 0x03#define REG_CONFIG_FLIP_TEST_PATTERN 0x02 +/* Input clock frequency in Hz */ +#define IMX258_INPUT_CLOCK_FREQ 19200000 +struct imx258_reg {u16 address;u8 val;
@@ -610,6 +614,8 @@ struct imx258 {/* Streaming on/off */ bool streaming; + +struct clk *clk; };static inline struct imx258 *to_imx258 (struct v4l2_subdev *_sd)
@@ -972,6 +978,29 @@ static int imx258_stop_streaming(struct imx258 *imx258)return 0 ; } +static int imx258_power_on (struct device *dev) +{ +struct v4l2_subdev *sd =dev_get_drvdata (dev); +struct imx258 *imx258 =to_imx258 (sd); +int ret; + + ret =clk_prepare_enable (imx258->clk); +if (ret) +dev_err (dev,"failed to enable clock\n" ); + +return ret; +} + +static int imx258_power_off (struct device *dev) +{ +struct v4l2_subdev *sd =dev_get_drvdata (dev); +struct imx258 *imx258 =to_imx258 (sd); + +clk_disable_unprepare (imx258->clk); + +return 0 ; +} +static int imx258_set_stream (struct v4l2_subdev *sd,int enable) {struct imx258 *imx258 =to_imx258 (sd);
@@ -1199,9 +1228,28 @@ static int imx258_probe(struct i2c_client *client)int ret;u32 val =0 ; -device_property_read_u32 (&client->dev,"clock-frequency" , &val); -if (val !=19200000 ) -return -EINVAL ; + imx258 =devm_kzalloc (&client->dev,sizeof (*imx258),GFP_KERNEL ); +if (!imx258) +return -ENOMEM ; + + imx258->clk =devm_clk_get_optional (&client->dev,NULL ); +if (!imx258->clk) { +dev_dbg (&client->dev, +"no clock provided, using clock-frequency property\n" ); + +device_property_read_u32 (&client->dev,"clock-frequency" , &val); +if (val !=IMX258_INPUT_CLOCK_FREQ ) +return -EINVAL ; + }else if (IS_ERR (imx258->clk)) { +return dev_err_probe (&client->dev,PTR_ERR (imx258->clk), +"error getting clock\n" ); + }else { +if (clk_get_rate (imx258->clk) !=IMX258_INPUT_CLOCK_FREQ ) { +dev_err (&client->dev, +"input clock frequency not supported\n" ); +return -EINVAL ; + } + }/* * Check that the device is mounted upside down. The driver only
@@ -1211,24 +1259,25 @@ static int imx258_probe(struct i2c_client *client)if (ret || val !=180 )return -EINVAL ; - imx258 =devm_kzalloc (&client->dev,sizeof (*imx258),GFP_KERNEL ); -if (!imx258) -return -ENOMEM ; -/* Initialize subdev */ v4l2_i2c_subdev_init (&imx258->sd, client, &imx258_subdev_ops); +/* Will be powered off via pm_runtime_idle */ + ret =imx258_power_on (&client->dev); +if (ret) +return ret; +/* Check module identity */ ret =imx258_identify_module (imx258);if (ret) -return ret; + goto error_identify;/* Set default mode to max resolution */ imx258->cur_mode = &supported_modes[0 ]; ret =imx258_init_controls (imx258);if (ret) -return ret; + goto error_identify;/* Initialize subdev */ imx258->sd.internal_ops = &imx258_internal_ops;
@@ -1258,6 +1307,9 @@ static int imx258_probe(struct i2c_client *client) error_handler_free:imx258_free_controls (imx258); +error_identify: +imx258_power_off (&client->dev); +return ret; }
@@ -1278,6 +1330,7 @@ static int imx258_remove(struct i2c_client *client)static const struct dev_pm_ops imx258_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(imx258_suspend, imx258_resume) +SET_RUNTIME_PM_OPS (imx258_power_off, imx258_power_on,NULL ) };#ifdef CONFIG_ACPI
Signature · 1 line
2.17.1
Quoted 14 lines · Krzysztof Kozlowski
Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v3:
1. Document also two lane setup.Changes since v2:
1. Remove clock-frequency, add reset GPIOs, add supplies.
2. Use additionalProperties.
Quoted 8 lines
Changes since v1:
1. None--- .../devicetree/bindings/media/i2c/imx258.yaml | 100 ++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 101 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/imx258.yaml
Sakari Ailus
maintainerHi Krzysztof,
Quoted 5 lines · Krzysztof Kozlowski
Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies.
Signed-off-by Krzysztof Kozlowski <[email protected]>
Quoted 7 lines
---
Changes since v3:
1. Document also two lane setup.Changes since v2:
1. Remove clock-frequency, add reset GPIOs, add supplies.
Oops. I missed this one.
How does the driver know the appropriate clock frequency for the platform if it's not in DT? The sensor supports a range of frequencies, not a single frequency.
Could you add clock-frequency back?
Signature · 3 lines
Kind regards, Sakari Ailus
Sakari Ailus
maintainerRe: [PATCH v4 4/4] media: i2c: imx258: get clock from device properties and enable it via runtime PM
In reply to Krzysztof KozlowskiHi Krzysztof,
Quoted 153 lines · Krzysztof Kozlowski
The IMX258 sensor driver checked in device properties for a clock-frequency property which actually does not mean that the clock is really running such frequency or is it even enabled.
Get the provided clock and check it frequency. If none is provided, fall back to old property.
Enable the clock when accessing the IMX258 registers and when streaming starts with runtime PM.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v3:
1. NoneChanges since v2:
1. Do not try to set drvdata, wrap lines.
2. Usedev_dbg.Changes since v1:
1. Use runtime PM for clock toggling--- drivers/media/i2c/imx258.c | 71 +++++++++++++++++++++++++++++++++----- 1 file changed, 62 insertions(+), 9 deletions(-)drivers/media/i2c/imx258.c +58
-9@@ -2,6 +2,7 @@// Copyright (C) 2018 Intel Corporation #include <linux/acpi.h> +#include <linux/clk.h> #include <linux/delay.h> #include <linux/i2c.h> #include <linux/module.h> @@ -68,6 +69,9 @@#define REG_CONFIG_MIRROR_FLIP 0x03#define REG_CONFIG_FLIP_TEST_PATTERN 0x02 +/* Input clock frequency in Hz */ +#define IMX258_INPUT_CLOCK_FREQ 19200000 +struct imx258_reg {u16 address;u8 val;@@ -610,6 +614,8 @@ struct imx258 {/* Streaming on/off */ bool streaming; + +struct clk *clk; };static inline struct imx258 *to_imx258 (struct v4l2_subdev *_sd)@@ -972,6 +978,29 @@ static int imx258_stop_streaming(struct imx258 *imx258)return 0 ; } +static int imx258_power_on (struct device *dev) +{ +struct v4l2_subdev *sd =dev_get_drvdata (dev); +struct imx258 *imx258 =to_imx258 (sd); +int ret; + + ret =clk_prepare_enable (imx258->clk); +if (ret) +dev_err (dev,"failed to enable clock\n" ); + +return ret; +} + +static int imx258_power_off (struct device *dev) +{ +struct v4l2_subdev *sd =dev_get_drvdata (dev); +struct imx258 *imx258 =to_imx258 (sd); + +clk_disable_unprepare (imx258->clk); + +return 0 ; +} +static int imx258_set_stream (struct v4l2_subdev *sd,int enable) {struct imx258 *imx258 =to_imx258 (sd);@@ -1199,9 +1228,28 @@ static int imx258_probe(struct i2c_client *client)int ret;u32 val =0 ; -device_property_read_u32 (&client->dev,"clock-frequency" , &val); -if (val !=19200000 ) -return -EINVAL ; + imx258 =devm_kzalloc (&client->dev,sizeof (*imx258),GFP_KERNEL ); +if (!imx258) +return -ENOMEM ; + + imx258->clk =devm_clk_get_optional (&client->dev,NULL ); +if (!imx258->clk) { +dev_dbg (&client->dev, +"no clock provided, using clock-frequency property\n" ); + +device_property_read_u32 (&client->dev,"clock-frequency" , &val); +if (val !=IMX258_INPUT_CLOCK_FREQ ) +return -EINVAL ; + }else if (IS_ERR (imx258->clk)) { +return dev_err_probe (&client->dev,PTR_ERR (imx258->clk), +"error getting clock\n" ); + }else { +if (clk_get_rate (imx258->clk) !=IMX258_INPUT_CLOCK_FREQ ) { +dev_err (&client->dev, +"input clock frequency not supported\n" ); +return -EINVAL ; + } + }/* * Check that the device is mounted upside down. The driver only @@ -1211,24 +1259,25 @@ static int imx258_probe(struct i2c_client *client)if (ret || val !=180 )return -EINVAL ; - imx258 =devm_kzalloc (&client->dev,sizeof (*imx258),GFP_KERNEL ); -if (!imx258) -return -ENOMEM ; -/* Initialize subdev */ v4l2_i2c_subdev_init (&imx258->sd, client, &imx258_subdev_ops); +/* Will be powered off via pm_runtime_idle */ + ret =imx258_power_on (&client->dev); +if (ret) +return ret; +/* Check module identity */ ret =imx258_identify_module (imx258);if (ret) -return ret; + goto error_identify;/* Set default mode to max resolution */ imx258->cur_mode = &supported_modes[0 ]; ret =imx258_init_controls (imx258);if (ret) -return ret; + goto error_identify;/* Initialize subdev */ imx258->sd.internal_ops = &imx258_internal_ops;
drivers/media/i2c/imx258.c static int imx258_probe(struct i2c_client *client) · line 1311
Quoted 5 lines
drivers/media/i2c/imx258.c +2
-0@@ -1258,6 +1307,9 @@ static int imx258_probe(struct i2c_client *client) error_handler_free:imx258_free_controls (imx258); +error_identify: +imx258_power_off (&client->dev);
You'll need this in remove callback, too.
Quoted 12 lines
drivers/media/i2c/imx258.c +2
-0+return ret; }@@ -1278,6 +1330,7 @@ static int imx258_remove(struct i2c_client *client)static const struct dev_pm_ops imx258_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(imx258_suspend, imx258_resume) +SET_RUNTIME_PM_OPS (imx258_power_off, imx258_power_on,NULL ) };#ifdef CONFIG_ACPI
Signature · 3 lines
Kind regards, Sakari Ailus
Quoted 17 lines · Sakari Ailus
Hi Krzysztof,
Quoted 5 lines · Krzysztof Kozlowski
Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies.
Signed-off-by Krzysztof Kozlowski <[email protected]>Quoted 7 lines
---
Changes since v3:
1. Document also two lane setup.Changes since v2:
1. Remove clock-frequency, add reset GPIOs, add supplies.
Quoted 7 lines
Oops. I missed this one.
How does the driver know the appropriate clock frequency for the platform if it's not in DT? The sensor supports a range of frequencies, not a single frequency.
Could you add clock-frequency back?
Not really, it was removed on Rob's request. The bindings do not describe driver's behavior so how the driver gets frequency should not be part of the bindings. Also it's not a real problem - the driver just calls clk_get_rate().
Best regards,
Krzysztof
Re: [PATCH v4 4/4] media: i2c: imx258: get clock from device properties and enable it via runtime PM
In reply to Sakari AilusQuoted 159 lines · Sakari Ailus
Hi Krzysztof,
Quoted 156 lines · Krzysztof Kozlowski
The IMX258 sensor driver checked in device properties for a clock-frequency property which actually does not mean that the clock is really running such frequency or is it even enabled.
Get the provided clock and check it frequency. If none is provided, fall back to old property.
Enable the clock when accessing the IMX258 registers and when streaming starts with runtime PM.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v3:
1. NoneChanges since v2:
1. Do not try to set drvdata, wrap lines.
2. Usedev_dbg.Changes since v1:
1. Use runtime PM for clock toggling--- drivers/media/i2c/imx258.c | 71 +++++++++++++++++++++++++++++++++----- 1 file changed, 62 insertions(+), 9 deletions(-)drivers/media/i2c/imx258.c +58
-9@@ -2,6 +2,7 @@// Copyright (C) 2018 Intel Corporation #include <linux/acpi.h> +#include <linux/clk.h> #include <linux/delay.h> #include <linux/i2c.h> #include <linux/module.h> @@ -68,6 +69,9 @@#define REG_CONFIG_MIRROR_FLIP 0x03#define REG_CONFIG_FLIP_TEST_PATTERN 0x02 +/* Input clock frequency in Hz */ +#define IMX258_INPUT_CLOCK_FREQ 19200000 +struct imx258_reg {u16 address;u8 val;@@ -610,6 +614,8 @@ struct imx258 {/* Streaming on/off */ bool streaming; + +struct clk *clk; };static inline struct imx258 *to_imx258 (struct v4l2_subdev *_sd)@@ -972,6 +978,29 @@ static int imx258_stop_streaming(struct imx258 *imx258)return 0 ; } +static int imx258_power_on (struct device *dev) +{ +struct v4l2_subdev *sd =dev_get_drvdata (dev); +struct imx258 *imx258 =to_imx258 (sd); +int ret; + + ret =clk_prepare_enable (imx258->clk); +if (ret) +dev_err (dev,"failed to enable clock\n" ); + +return ret; +} + +static int imx258_power_off (struct device *dev) +{ +struct v4l2_subdev *sd =dev_get_drvdata (dev); +struct imx258 *imx258 =to_imx258 (sd); + +clk_disable_unprepare (imx258->clk); + +return 0 ; +} +static int imx258_set_stream (struct v4l2_subdev *sd,int enable) {struct imx258 *imx258 =to_imx258 (sd);@@ -1199,9 +1228,28 @@ static int imx258_probe(struct i2c_client *client)int ret;u32 val =0 ; -device_property_read_u32 (&client->dev,"clock-frequency" , &val); -if (val !=19200000 ) -return -EINVAL ; + imx258 =devm_kzalloc (&client->dev,sizeof (*imx258),GFP_KERNEL ); +if (!imx258) +return -ENOMEM ; + + imx258->clk =devm_clk_get_optional (&client->dev,NULL ); +if (!imx258->clk) { +dev_dbg (&client->dev, +"no clock provided, using clock-frequency property\n" ); + +device_property_read_u32 (&client->dev,"clock-frequency" , &val); +if (val !=IMX258_INPUT_CLOCK_FREQ ) +return -EINVAL ; + }else if (IS_ERR (imx258->clk)) { +return dev_err_probe (&client->dev,PTR_ERR (imx258->clk), +"error getting clock\n" ); + }else { +if (clk_get_rate (imx258->clk) !=IMX258_INPUT_CLOCK_FREQ ) { +dev_err (&client->dev, +"input clock frequency not supported\n" ); +return -EINVAL ; + } + }/* * Check that the device is mounted upside down. The driver only @@ -1211,24 +1259,25 @@ static int imx258_probe(struct i2c_client *client)if (ret || val !=180 )return -EINVAL ; - imx258 =devm_kzalloc (&client->dev,sizeof (*imx258),GFP_KERNEL ); -if (!imx258) -return -ENOMEM ; -/* Initialize subdev */ v4l2_i2c_subdev_init (&imx258->sd, client, &imx258_subdev_ops); +/* Will be powered off via pm_runtime_idle */ + ret =imx258_power_on (&client->dev); +if (ret) +return ret; +/* Check module identity */ ret =imx258_identify_module (imx258);if (ret) -return ret; + goto error_identify;/* Set default mode to max resolution */ imx258->cur_mode = &supported_modes[0 ]; ret =imx258_init_controls (imx258);if (ret) -return ret; + goto error_identify;/* Initialize subdev */ imx258->sd.internal_ops = &imx258_internal_ops;@@ -1258,6 +1307,9 @@ static int imx258_probe(struct i2c_client *client) error_handler_free:imx258_free_controls (imx258);
Quoted 4 lines
drivers/media/i2c/imx258.c static int imx258_probe(struct i2c_client *client) · line 1311
Quoted 2 lines
drivers/media/i2c/imx258.c +2
-0+error_identify: +imx258_power_off (&client->dev);You'll need this in remove callback, too.
True, there is no runtime idle call so this is missing.
Thanks.
Best regards,
Krzysztof
Sakari Ailus
maintainerQuoted 24 lines · Krzysztof Kozlowski
Quoted 23 lines · Sakari Ailus
Hi Krzysztof,
Quoted 5 lines · Krzysztof Kozlowski
Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies.
Signed-off-by Krzysztof Kozlowski <[email protected]>Quoted 7 lines
---
Changes since v3:
1. Document also two lane setup.Changes since v2:
1. Remove clock-frequency, add reset GPIOs, add supplies.Oops. I missed this one.
How does the driver know the appropriate clock frequency for the platform if it's not in DT? The sensor supports a range of frequencies, not a single frequency.
Quoted 6 lines
Quoted 1 line
Could you add clock-frequency back?
Not really, it was removed on Rob's request. The bindings do not describe driver's behavior so how the driver gets frequency should not be part of the bindings. Also it's not a real problem - the driver just calls
clk_get_rate().
How is the rate determined? I mean, many ISPs or CSI-2 receivers that provide the clock are also capable of using a variety of frequencies. But only one can be used on the platform in general.
Where does it come from if it's not in DT?
Using another frequency generally leads to failure later on as the desired link frequency likely is not available for a random external clock frequency.
Signature · 1 line
Sakari Ailus
Sakari Ailus
maintainerQuoted 24 lines · Krzysztof Kozlowski
Quoted 23 lines · Sakari Ailus
Hi Krzysztof,
Quoted 5 lines · Krzysztof Kozlowski
Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies.
Signed-off-by Krzysztof Kozlowski <[email protected]>Quoted 7 lines
---
Changes since v3:
1. Document also two lane setup.Changes since v2:
1. Remove clock-frequency, add reset GPIOs, add supplies.Oops. I missed this one.
How does the driver know the appropriate clock frequency for the platform if it's not in DT? The sensor supports a range of frequencies, not a single frequency.
Quoted 6 lines
Quoted 1 line
Could you add clock-frequency back?
Not really, it was removed on Rob's request. The bindings do not describe driver's behavior so how the driver gets frequency should not be part of the bindings. Also it's not a real problem - the driver just calls
clk_get_rate().
Btw. we also have this nowadays:Documentation/driver-api/media/camera-sensor.rst .
Signature · 1 line
Sakari Ailus
Quoted 27 lines · Sakari Ailus
Quoted 26 lines · Krzysztof Kozlowski
Quoted 24 lines · Sakari Ailus
Hi Krzysztof,
Quoted 5 lines · Krzysztof Kozlowski
Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies.
Signed-off-by Krzysztof Kozlowski <[email protected]>Quoted 7 lines
---
Changes since v3:
1. Document also two lane setup.Changes since v2:
1. Remove clock-frequency, add reset GPIOs, add supplies.Oops. I missed this one.
How does the driver know the appropriate clock frequency for the platform if it's not in DT? The sensor supports a range of frequencies, not a single frequency.
Could you add clock-frequency back?
Quoted 8 lines
Quoted 4 lines
Not really, it was removed on Rob's request. The bindings do not describe driver's behavior so how the driver gets frequency should not be part of the bindings. Also it's not a real problem - the driver just calls
clk_get_rate().How is the rate determined? I mean, many ISPs or CSI-2 receivers that provide the clock are also capable of using a variety of frequencies. But only one can be used on the platform in general.
Having "clock-frequency" property in DTS did not solve that. It has no effect on actual frequency.
Quoted 2 lines
Where does it come from if it's not in DT?
The frequency is either chosen by consumer (imx258) or pre-assigned from DT, but not with "clock-frequency" property. There are generic properties for this: assigned-clocks, assigned-clock-rates and assigned-clock-parents.
These properties should be added to DTS if additionalProperties is false, which is the case here... so I could add them. My DTS anyway does not use them, as the clock is generated internally on a camera board so I don't have a control over it.
Best regards,
Krzysztof
Quoted 4 lines
Using another frequency generally leads to failure later on as the desired link frequency likely is not available for a random external clock frequency.
Sakari Ailus
maintainerQuoted 33 lines · Krzysztof Kozlowski
Quoted 32 lines · Sakari Ailus
Quoted 30 lines · Krzysztof Kozlowski
Quoted 17 lines · Sakari Ailus
Hi Krzysztof,
Quoted 5 lines · Krzysztof Kozlowski
Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies.
Signed-off-by Krzysztof Kozlowski <[email protected]>Quoted 7 lines
---
Changes since v3:
1. Document also two lane setup.Changes since v2:
1. Remove clock-frequency, add reset GPIOs, add supplies.Quoted 7 lines
Oops. I missed this one.
How does the driver know the appropriate clock frequency for the platform if it's not in DT? The sensor supports a range of frequencies, not a single frequency.
Could you add clock-frequency back?
Not really, it was removed on Rob's request. The bindings do not describe driver's behavior so how the driver gets frequency should not be part of the bindings. Also it's not a real problem - the driver just calls
clk_get_rate().
Quoted 6 lines
Quoted 3 lines
How is the rate determined? I mean, many ISPs or CSI-2 receivers that provide the clock are also capable of using a variety of frequencies. But only one can be used on the platform in general.
Having "clock-frequency" property in DTS did not solve that. It has no effect on actual frequency.
It's up to the driver to do what's needed, yes.
Please see examples in e.g. drivers/media/i2c/ov8856.c and Documentation/devicetree/bindings/media/i2c/ov8856.yaml .
Signature · 1 line
Sakari Ailus
Quoted 38 lines · Sakari Ailus
Quoted 37 lines · Krzysztof Kozlowski
Quoted 35 lines · Sakari Ailus
Quoted 24 lines · Krzysztof Kozlowski
Quoted 23 lines · Sakari Ailus
Hi Krzysztof,
Quoted 5 lines · Krzysztof Kozlowski
Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies.
Signed-off-by Krzysztof Kozlowski <[email protected]>Quoted 7 lines
---
Changes since v3:
1. Document also two lane setup.Changes since v2:
1. Remove clock-frequency, add reset GPIOs, add supplies.Oops. I missed this one.
How does the driver know the appropriate clock frequency for the platform if it's not in DT? The sensor supports a range of frequencies, not a single frequency.
Quoted 6 lines
Quoted 1 line
Could you add clock-frequency back?
Not really, it was removed on Rob's request. The bindings do not describe driver's behavior so how the driver gets frequency should not be part of the bindings. Also it's not a real problem - the driver just calls
clk_get_rate().How is the rate determined? I mean, many ISPs or CSI-2 receivers that provide the clock are also capable of using a variety of frequencies. But only one can be used on the platform in general.
Quoted 7 lines
Quoted 2 lines
Having "clock-frequency" property in DTS did not solve that. It has no effect on actual frequency.
It's up to the driver to do what's needed, yes.
Please see examples in e.g.
drivers/media/i2c/ov8856.candDocumentation/devicetree/bindings/media/i2c/ov8856.yaml.
It seems the ov8856 driver uses this property in different way than imx258 driver. It is more appropriate and quite similar to clock providers and buses - to set the desired frequency on input clock.
Therefore what is the point of using this DT property comparing to assigned-clock-rates?
It's the same. So let's use generic (already documented) assigned-clock-rates.
For your question (not related to the bindings but to driver implementation): "How is the rate determined?", simple: clk_get_rate. The driver then uses it like this:
if (clk_get_rate() != only_working_configuration_hz) return -EINVAL;
From the bindings point of view, the clock can be anything within a range of sensor's accepted values. The clock frequency is a property of a clock, not of a sensor. Therefore for HW description it should be described in the clock bindings, not in the sensor bindings.
To summarize, the "clock-frequency" property of sensor node:
1. As a way to configure the clock should be replaced with assigned-clock properties,
2. As a way to describe the hardware is simply invalid. It is not a HW description, because HW requires just a clock of frequency within given range, not a fixed frequency clock.
Consider the example:
camera@1a {
compatible = "sony,imx258";
reg = <0x1a>;
clocks = <&imx258_clk>;
clock-names = "clk";
/* Oscillator on camera board */
imx258_clk: clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
};
port {
...
};
};What is the point to add "clock-frequency" property to the camera itself, since it is already clearly defined by the clock?
Or another example:
camera@1a {
compatible = "sony,imx258";
reg = <0x1a>;
clocks = <&iclk 0>;
clock-names = "clk";
assigned-clocks = <&clk 0>;
assigned-clock-rates = <19200000>;
port {
...
};
};Again, no reason for artificial clock-frequency property. It is not part of HW description of the sensor.
Best regards,
Krzysztof