Skip to contentSkip to conversation

Sama7g5 Evaluation Kit support

PATCH Superseded Eugen Hristev 2 participants 42 messages Dec 3, 2020 – Dec 6, 2020

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

cover Sama7g5 Evaluation Kit support

Hello,

This series adds support for sama7g5 SoC DT and the sama7g5ek board. I kept the original incremental development for this board, with each commit's author and designated change, for traceability and for easier reviewing.

The series starts from a basic devicetree and ends with a fully functional board including SD-Card/MMC, i2c eeproms, ethernet.

Thanks,
Eugen

Claudiu Beznea (20):
board: atmel: sama7g5ek: add SYS_MALLOC_F_LEN to SYS_INIT_SP_ADDR
configs: sama7g5ek: set malloc pool to 68K
configs: sama7g5ek: enable pll driver
ARM: dts: sama7g5: move clock frequencies for xtals in board file
ARM: dts: sama7g5: add slow rc and main rc oscillators
ARM: dts: sama7g5: add u-boot,dm-pre-reloc bindings for xtals
ARM: dts: sama7g5: add slow clock bindings
ARM: dts: sama7g5: add PMC bindings
ARM: dts: sama7g5: switch to PMC bindings
configs: sama7g5: enable CONFIG_CPU
ARM: dts: sama7g5: add CPU bindings
configs: sama7g5: use PIT64B
ARM: dts: sama7g5: enable autoboot
ARM: dts: sama7g5: add pit64b support
configs: sama7g5ek: enable mii command
ARM: dts: sama7g5: add GMAC0
ARM: dts: sama7g5: add GMAC1
board: atmel: sama7g5ek: increase arp timeout and retry count
configs: sama7g5ek: enable support for KSZ9131
configs: sama7g5ek: enable CCF

Eugen Hristev (13):
ARM: dts: sama7g5: add initial DT for sama7g5 SoC
board: atmel: sama7g5ek: add initial support for sama7g5ek
ARM: dts: at91: sama7g5: add pinctrl node
ARM: dts: at91: sama7g5ek: add pinctrl for sdmmc1 and flx3
ARM: dts: at91: sama7g5: add assigned clocks for sdmmc1
ARM: dts: at91: sama7g5: add node for sdmmc0
ARM: dts: at91: sama7g5ek: enable sdmmc0 with pinctrl
board: atmel: sama7g5ek: clean-up header bootcommand
configs: sama7g5: add mmc config for sdmmc0
ARM: dts: at91: sama7g5: add flexcom1 and i2c subnode
ARM: dts: sama7g5ek: add i2c1 bus and eeproms
board: atmel: sama7g5ek: add support for MAC address retreival
configs: sama7g5ek: add i2c and eeprom

Nicolas Ferre (1):
ARM: dts: sama7g5ek: fix TXC pin configuration

 arch/arm/dts/Makefile              |   3 +
 arch/arm/dts/sama7g5.dtsi          | 169 ++++++++++++++++++++++++
 arch/arm/dts/sama7g5ek-u-boot.dtsi |  65 ++++++++++
 arch/arm/dts/sama7g5ek.dts         | 202 +++++++++++++++++++++++++++++
 arch/arm/mach-at91/Kconfig         |   8 ++
 board/atmel/sama7g5ek/Kconfig      |  15 +++
 board/atmel/sama7g5ek/MAINTAINERS  |   8 ++
 board/atmel/sama7g5ek/Makefile     |   7 +
 board/atmel/sama7g5ek/sama7g5ek.c  |  76 +++++++++++
 configs/sama7g5ek_mmc1_defconfig   |  70 ++++++++++
 configs/sama7g5ek_mmc_defconfig    |  70 ++++++++++
 include/configs/sama7g5ek.h        |  45 +++++++
 12 files changed, 738 insertions(+)
 create mode 100644 arch/arm/dts/sama7g5.dtsi
 create mode 100644 arch/arm/dts/sama7g5ek-u-boot.dtsi
 create mode 100644 arch/arm/dts/sama7g5ek.dts
 create mode 100644 board/atmel/sama7g5ek/Kconfig
 create mode 100644 board/atmel/sama7g5ek/MAINTAINERS
 create mode 100644 board/atmel/sama7g5ek/Makefile
 create mode 100644 board/atmel/sama7g5ek/sama7g5ek.c
 create mode 100644 configs/sama7g5ek_mmc1_defconfig
 create mode 100644 configs/sama7g5ek_mmc_defconfig
 create mode 100644 include/configs/sama7g5ek.h
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/34 ARM: dts: sama7g5: add initial DT for sama7g5 SoC

Add initial basic devicetree for sama7g5 SoC

---
 arch/arm/dts/sama7g5.dtsi | 65 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 65 insertions(+)
 create mode 100644 arch/arm/dts/sama7g5.dtsi
arch/arm/dts/sama7g5.dtsi new file +65 -0
new file mode 100644
index 0000000000..24b6f90957
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sama7g5.dtsi - Device Tree Include file for SAMA7G5 SoC.
+ *
+ * Copyright (C) 2020 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Eugen Hristev <[email protected]>
+ * Author: Claudiu Beznea <[email protected]>
+ *
+ */
+
+#include "skeleton.dtsi"
+
+/ {
+	model = "Microchip SAMA7G5 family SoC";
+	compatible = "microchip,sama7g5";
+
+	clocks {
+		slow_xtal: slow_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+		};
+
+		main_xtal: main_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+		};
+
+		mck: mck {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		apb {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			sdmmc1: sdio-host at e1208000 {
+				compatible = "microchip,sama7g5-sdhci";
+				reg = <0xe1208000 0x300>;
+				clocks = <&mck>, <&mck>, <&mck>;
+				clock-names = "hclock", "multclk", "baseclk";
+				status = "disabled";
+			};
+
+			uart0: serial at e1824200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0xe1824200 0x200>;
+				clocks = <&mck>;
+				clock-names = "usart";
+				status = "disabled";
+			};
+		};
+	};
+};
Signature · 1 line
2.25.1
#2 lore raw

PATCH 2/34 board: atmel: sama7g5ek: add initial support for sama7g5ek

In reply to Eugen Hristev

Add initial support for sama7g5 evaluation kit board.

---
 arch/arm/dts/Makefile              |  3 ++
 arch/arm/dts/sama7g5ek-u-boot.dtsi | 33 +++++++++++++++
 arch/arm/dts/sama7g5ek.dts         | 39 +++++++++++++++++
 arch/arm/mach-at91/Kconfig         |  8 ++++
 board/atmel/sama7g5ek/Kconfig      | 15 +++++++
 board/atmel/sama7g5ek/MAINTAINERS  |  7 +++
 board/atmel/sama7g5ek/Makefile     |  7 +++
 board/atmel/sama7g5ek/sama7g5ek.c  | 68 ++++++++++++++++++++++++++++++
 configs/sama7g5ek_mmc1_defconfig   | 59 ++++++++++++++++++++++++++
 include/configs/sama7g5ek.h        | 46 ++++++++++++++++++++
 10 files changed, 285 insertions(+)
 create mode 100644 arch/arm/dts/sama7g5ek-u-boot.dtsi
 create mode 100644 arch/arm/dts/sama7g5ek.dts
 create mode 100644 board/atmel/sama7g5ek/Kconfig
 create mode 100644 board/atmel/sama7g5ek/MAINTAINERS
 create mode 100644 board/atmel/sama7g5ek/Makefile
 create mode 100644 board/atmel/sama7g5ek/sama7g5ek.c
 create mode 100644 configs/sama7g5ek_mmc1_defconfig
 create mode 100644 include/configs/sama7g5ek.h
arch/arm/dts/Makefile +3 -0
index 5308713df7..fa5590561a 100644
@@ -886,6 +886,9 @@ dtb-$(CONFIG_TARGET_OMAP4_SDP4430) += \
 dtb-$(CONFIG_TARGET_OMAP5_UEVM) += \
 	omap5-uevm.dtb
 
+dtb-$(CONFIG_TARGET_SAMA7G5EK) += \
+	sama7g5ek.dtb
+
 dtb-$(CONFIG_TARGET_SAMA5D2_PTC_EK) += \
 	at91-sama5d2_ptc_ek.dtb
 
arch/arm/dts/sama7g5ek-u-boot.dtsi new file +33 -0
new file mode 100644
index 0000000000..c0f8f94027
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sama7g5ek-u-boot.dts - Device Tree file for SAMA7G5 SoC u-boot properties.
+ *
+ * Copyright (C) 2020 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Eugen Hristev <[email protected]>
+ * Author: Claudiu Beznea <[email protected]>
+ *
+ */
+
+/ {
+	chosen {
+		u-boot,dm-pre-reloc;
+	};
+
+	ahb {
+		u-boot,dm-pre-reloc;
+
+		apb {
+			u-boot,dm-pre-reloc;
+		};
+	};
+};
+
+&uart0 {
+	u-boot,dm-pre-reloc;
+};
+
+&mck {
+	u-boot,dm-pre-reloc;
+};
+
arch/arm/dts/sama7g5ek.dts new file +39 -0
new file mode 100644
index 0000000000..41a754df6f
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * sama7g5ek.dts - Device Tree file for SAMA7G5 EK
+ *		   SAMA7G5 Evaluation Kit
+ *
+ *  Copyright (c) 2020, Microchip Technology Inc.
+ *                2020, Eugen Hristev <[email protected]>
+ *		  2020, Claudiu Beznea <[email protected]>
+ */
+/dts-v1/;
+#include "sama7g5.dtsi"
+#include "sama7g5-pinfunc.h"
+
+/ {
+	model = "Microchip SAMA7G5 Evaluation Kit";
+	compatible = "microchip,sama7g5ek", "microchip,sama7g54", "microchip,sama7g5", "microchip,sama7";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ahb {
+
+		apb {
+			sdmmc1: sdio-host at e1208000 {
+				bus-width = <4>;
+				status = "okay";
+			};
+
+			uart0: serial at e1824200 {
+				status = "okay";
+			};
+		};
+	};
+};
arch/arm/mach-at91/Kconfig +8 -0
index be1415f909..c78a308f48 100644
@@ -265,6 +265,13 @@ config TARGET_CORVUS
 	select SUPPORT_SPL
 	imply CMD_DM
 
+config TARGET_SAMA7G5EK
+       bool "SAMA7G5 EK board"
+       select SAMA7G5
+       select BOARD_EARLY_INIT_F
+       select BOARD_LATE_INIT
+
+
 config TARGET_TAURUS
 	bool "Support taurus"
 	select AT91SAM9G20
@@ -327,6 +334,7 @@ source "board/atmel/at91sam9n12ek/Kconfig"
 source "board/atmel/at91sam9rlek/Kconfig"
 source "board/atmel/at91sam9x5ek/Kconfig"
 source "board/atmel/sam9x60ek/Kconfig"
+source "board/atmel/sama7g5ek/Kconfig"
 source "board/atmel/sama5d2_ptc_ek/Kconfig"
 source "board/atmel/sama5d2_xplained/Kconfig"
 source "board/atmel/sama5d27_som1_ek/Kconfig"
board/atmel/sama7g5ek/Kconfig new file +15 -0
new file mode 100644
index 0000000000..a89db8d8a8
@@ -0,0 +1,15 @@
+if TARGET_SAMA7G5EK
+
+config SYS_BOARD
+	default "sama7g5ek"
+
+config SYS_VENDOR
+	default "atmel"
+
+config SYS_SOC
+	default "at91"
+
+config SYS_CONFIG_NAME
+	default "sama7g5ek"
+
+endif
board/atmel/sama7g5ek/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000000..f66953ac4e
@@ -0,0 +1,7 @@
+SAMA7G5 EK BOARD
+M:     Eugen Hristev <[email protected]>
+S:     Maintained
+F:     board/atmel/sama7g5ek.c
+F:     include/configs/sama7g5ek.h
+F:     configs/sama7g5ek_mmc1_defconfig
+
board/atmel/sama7g5ek/Makefile new file +7 -0
new file mode 100644
index 0000000000..a6eedd10fa
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier:     GPL-2.0+
+#
+# Copyright (C) 2020 Microchip Technology Inc.
+#                   Eugen Hristev <[email protected]>
+#
+
+obj-y += sama7g5ek.o
board/atmel/sama7g5ek/sama7g5ek.c new file +68 -0

68 lines not on this page · raw message

configs/sama7g5ek_mmc1_defconfig new file +59 -0

59 lines not on this page · raw message

include/configs/sama7g5ek.h new file +46 -0

46 lines not on this page · raw message

Signature · 1 line
2.25.1
#3 lore raw

PATCH 3/34 board: atmel: sama7g5ek: add SYS_MALLOC_F_LEN to SYS_INIT_SP_ADDR

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Heap base address is computed based on SYS_INIT_SP_ADDR by subtracting the SYS_MALLOC_F_LEN value in board_init_f_init_reserve().

---
 include/configs/sama7g5ek.h | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
include/configs/sama7g5ek.h +2 -1
index 3b3432ba5e..fbf0274b38 100644
@@ -20,7 +20,8 @@
 #define CONFIG_SYS_INIT_SP_ADDR		0x218000
 #else
 #define CONFIG_SYS_INIT_SP_ADDR \
-	(CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
+	(CONFIG_SYS_SDRAM_BASE + 16 * 1024 + CONFIG_SYS_MALLOC_F_LEN - \
+	 GENERATED_GBL_DATA_SIZE)
 #endif
 
 #define CONFIG_SYS_LOAD_ADDR		0x62000000 /* load address */
Signature · 1 line
2.25.1
#4 lore raw

PATCH 4/34 configs: sama7g5ek: set malloc pool to 68K

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Set malloc pool to 68K for sama7g5ek.

---
 configs/sama7g5ek_mmc1_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
index d54af0ccbf..2da766d4e2 100644
@@ -3,6 +3,7 @@ CONFIG_ARCH_AT91=y
 CONFIG_SYS_TEXT_BASE=0x66f00000
 CONFIG_TARGET_SAMA7G5EK=y
 CONFIG_NR_DRAM_BANKS=1
+CONFIG_SYS_MALLOC_F_LEN=0x11000
 CONFIG_ENV_SIZE=0x4000
 CONFIG_DM_GPIO=y
 CONFIG_DEBUG_UART_BOARD_INIT=y
Signature · 1 line
2.25.1
#5 lore raw

PATCH 5/34 configs: sama7g5ek: enable pll driver

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Enable PLL driver for SAMA7G5.

---
 configs/sama7g5ek_mmc1_defconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
configs/sama7g5ek_mmc1_defconfig +2 -1
index 2da766d4e2..d43d07da78 100644
@@ -5,7 +5,6 @@ CONFIG_TARGET_SAMA7G5EK=y
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_SYS_MALLOC_F_LEN=0x11000
 CONFIG_ENV_SIZE=0x4000
-CONFIG_DM_GPIO=y
 CONFIG_DEBUG_UART_BOARD_INIT=y
 CONFIG_DEBUG_UART_BASE=0xe1824200
 CONFIG_DEBUG_UART_CLOCK=200000000
@@ -42,6 +41,8 @@ CONFIG_CLK=y
 CONFIG_CLK_AT91=y
 CONFIG_AT91_UTMI=y
 CONFIG_AT91_GENERIC_CLK=y
+CONFIG_AT91_SAM9X60_PLL=y
+CONFIG_DM_GPIO=y
 CONFIG_ATMEL_PIO4=y
 CONFIG_DM_I2C=y
 CONFIG_DM_MMC=y
Signature · 1 line
2.25.1
#6 lore raw

PATCH 6/34 ARM: dts: sama7g5: move clock frequencies for xtals in board file

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Move clock frequencies for crystals on board specific files.

---
 arch/arm/dts/sama7g5.dtsi  |  2 --
 arch/arm/dts/sama7g5ek.dts | 10 ++++++++++
 2 files changed, 10 insertions(+), 2 deletions(-)
arch/arm/dts/sama7g5.dtsi +0 -2
index 24b6f90957..618f3a37d5 100644
@@ -19,13 +19,11 @@
 		slow_xtal: slow_xtal {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <0>;
 		};
 
 		main_xtal: main_xtal {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <0>;
 		};
 
 		mck: mck {
arch/arm/dts/sama7g5ek.dts +10 -0
index 41a754df6f..03c7aa07ea 100644
@@ -23,6 +23,16 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	clocks {
+		slow_xtal: slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal: main_xtal {
+			clock-frequency = <24000000>;
+		};
+	};
+
 	ahb {
 
 		apb {
Signature · 1 line
2.25.1
#7 lore raw

PATCH 7/34 ARM: dts: sama7g5: add slow rc and main rc oscillators

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Add slow rc and main rc oscillators to dtsi.

---
 arch/arm/dts/sama7g5.dtsi          | 12 ++++++++++++
 arch/arm/dts/sama7g5ek-u-boot.dtsi |  8 ++++++++
 2 files changed, 20 insertions(+)
arch/arm/dts/sama7g5.dtsi +12 -0
index 618f3a37d5..c2410959ed 100644
@@ -16,6 +16,18 @@
 	compatible = "microchip,sama7g5";
 
 	clocks {
+		slow_rc_osc: slow_rc_osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <18500>;
+		};
+
+		main_rc: main_rc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <12000000>;
+		};
+
 		slow_xtal: slow_xtal {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
arch/arm/dts/sama7g5ek-u-boot.dtsi +8 -0
index c0f8f94027..06af2f74ee 100644
@@ -23,6 +23,14 @@
 	};
 };
 
+&main_rc {
+	u-boot,dm-pre-reloc;
+};
+
+&slow_rc_osc {
+	u-boot,dm-pre-reloc;
+};
+
 &uart0 {
 	u-boot,dm-pre-reloc;
 };
Signature · 1 line
2.25.1
#8 lore raw

PATCH 8/34 ARM: dts: sama7g5: add u-boot, dm-pre-reloc bindings for xtals

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Add dm-pre-reloc DT binding property for cristals.

---
 arch/arm/dts/sama7g5ek-u-boot.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)
arch/arm/dts/sama7g5ek-u-boot.dtsi +8 -0
index 06af2f74ee..d10448e031 100644
@@ -27,10 +27,18 @@
 	u-boot,dm-pre-reloc;
 };
 
+&main_xtal {
+	u-boot,dm-pre-reloc;
+};
+
 &slow_rc_osc {
 	u-boot,dm-pre-reloc;
 };
 
+&slow_xtal {
+	u-boot,dm-pre-reloc;
+};
+
 &uart0 {
 	u-boot,dm-pre-reloc;
 };
Signature · 1 line
2.25.1
#9 lore raw

PATCH 9/34 ARM: dts: sama7g5: add slow clock bindings

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Add DT bindings for slow clock driver.

---
 arch/arm/dts/sama7g5.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm/dts/sama7g5.dtsi +7 -0
index c2410959ed..9d390db5ff 100644
@@ -55,6 +55,13 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			clk32: sckc at e001d050 {
+				compatible = "microchip,sam9x60-sckc";
+				reg = <0xe001d050 0x4>;
+				clocks = <&slow_rc_osc>, <&slow_xtal>;
+				#clock-cells = <1>;
+			};
+
 			sdmmc1: sdio-host at e1208000 {
 				compatible = "microchip,sama7g5-sdhci";
 				reg = <0xe1208000 0x300>;
Signature · 1 line
2.25.1
#10 lore raw

PATCH 10/34 ARM: dts: sama7g5: add PMC bindings

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Add DT bindings for PMC driver.

---
 arch/arm/dts/sama7g5.dtsi          | 9 +++++++++
 arch/arm/dts/sama7g5ek-u-boot.dtsi | 4 ++++
 2 files changed, 13 insertions(+)
arch/arm/dts/sama7g5.dtsi +9 -0
index 9d390db5ff..28faa412dd 100644
@@ -55,6 +55,15 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			pmc: pmc at e0018000 {
+				compatible = "microchip,sama7g5-pmc";
+				reg = <0xe0018000 0x200>;
+				#clock-cells = <2>;
+				clocks = <&clk32 1>, <&clk32 0>, <&main_xtal>, <&main_rc>;
+				clock-names = "td_slck", "md_slck", "main_xtal", "main_rc";
+				status = "okay";
+			};
+
 			clk32: sckc at e001d050 {
 				compatible = "microchip,sam9x60-sckc";
 				reg = <0xe001d050 0x4>;
arch/arm/dts/sama7g5ek-u-boot.dtsi +4 -0
index d10448e031..428b98c303 100644
@@ -31,6 +31,10 @@
 	u-boot,dm-pre-reloc;
 };
 
+&pmc {
+	u-boot,dm-pre-reloc;
+};
+
 &slow_rc_osc {
 	u-boot,dm-pre-reloc;
 };
Signature · 1 line
2.25.1
#11 lore raw

PATCH 11/34 ARM: dts: sama7g5: switch to PMC bindings

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Get rid of software defined MCK and switch to PMC bindings for IPs currently present in device tree.

---
 arch/arm/dts/sama7g5.dtsi          | 13 ++++---------
 arch/arm/dts/sama7g5ek-u-boot.dtsi |  4 ----
 2 files changed, 4 insertions(+), 13 deletions(-)
arch/arm/dts/sama7g5.dtsi +4 -9
index 28faa412dd..94e0b535cc 100644
@@ -10,6 +10,7 @@
  */
 
 #include "skeleton.dtsi"
+#include <dt-bindings/clk/at91.h>
 
 / {
 	model = "Microchip SAMA7G5 family SoC";
@@ -37,12 +38,6 @@
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 		};
-
-		mck: mck {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <200000000>;
-		};
 	};
 
 	ahb {
@@ -74,15 +69,15 @@
 			sdmmc1: sdio-host at e1208000 {
 				compatible = "microchip,sama7g5-sdhci";
 				reg = <0xe1208000 0x300>;
-				clocks = <&mck>, <&mck>, <&mck>;
-				clock-names = "hclock", "multclk", "baseclk";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 81>, <&pmc PMC_TYPE_GCK 81>;
+				clock-names = "hclock", "multclk";
 				status = "disabled";
 			};
 
 			uart0: serial at e1824200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xe1824200 0x200>;
-				clocks = <&mck>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
 				clock-names = "usart";
 				status = "disabled";
 			};
arch/arm/dts/sama7g5ek-u-boot.dtsi +0 -4
index 428b98c303..95d9c3bff2 100644
@@ -47,7 +47,3 @@
 	u-boot,dm-pre-reloc;
 };
 
-&mck {
-	u-boot,dm-pre-reloc;
-};
-
Signature · 1 line
2.25.1
#12 lore raw

PATCH 12/34 configs: sama7g5: enable CONFIG_CPU

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Enable CONFIG_CPU.

---
 configs/sama7g5ek_mmc1_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
index d43d07da78..936d9cd73f 100644
@@ -42,6 +42,7 @@ CONFIG_CLK_AT91=y
 CONFIG_AT91_UTMI=y
 CONFIG_AT91_GENERIC_CLK=y
 CONFIG_AT91_SAM9X60_PLL=y
+CONFIG_CPU=y
 CONFIG_DM_GPIO=y
 CONFIG_ATMEL_PIO4=y
 CONFIG_DM_I2C=y
Signature · 1 line
2.25.1
#13 lore raw

PATCH 13/34 ARM: dts: sama7g5: add CPU bindings

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Add CPU DT bindings.

---
 arch/arm/dts/sama7g5.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)
arch/arm/dts/sama7g5.dtsi +12 -0
index 94e0b535cc..a2554dcfff 100644
@@ -40,6 +40,18 @@
 		};
 	};
 
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		A7_0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			clocks = <&pmc PMC_TYPE_CORE 8>, <&pmc PMC_TYPE_CORE 22>, <&main_xtal>;
+			clock-names = "cpu", "master", "xtal";
+		};
+	};
+
 	ahb {
 		compatible = "simple-bus";
 		#address-cells = <1>;
Signature · 1 line
2.25.1
#14 lore raw

PATCH 14/34 configs: sama7g5: use PIT64B

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Use PIT64B driver. ATMEL_PIT is not available for SAMA7G5.

---
 configs/sama7g5ek_mmc1_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
index 936d9cd73f..7d4d409532 100644
@@ -58,5 +58,6 @@ CONFIG_DM_SERIAL=y
 CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_ATMEL_USART=y
 CONFIG_TIMER=y
+CONFIG_MCHP_PIT64B_TIMER=y
 CONFIG_OF_LIBFDT_OVERLAY=y
 # CONFIG_EFI_LOADER_HII is not set
Signature · 1 line
2.25.1
#15 lore raw

PATCH 15/34 ARM: dts: sama7g5: enable autoboot

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Enable autoboot.

---
 configs/sama7g5ek_mmc1_defconfig | 1 -
 1 file changed, 1 deletion(-)
configs/sama7g5ek_mmc1_defconfig +0 -1
index 7d4d409532..99e2439516 100644
@@ -16,7 +16,6 @@ CONFIG_SD_BOOT=y
 CONFIG_USE_BOOTARGS=y
 CONFIG_MISC_INIT_R=y
 CONFIG_HUSH_PARSER=y
-# CONFIG_AUTOBOOT is not set
 CONFIG_CMD_BOOTZ=y
 # CONFIG_CMD_IMI is not set
 CONFIG_CMD_MD5SUM=y
Signature · 1 line
2.25.1
#16 lore raw

PATCH 16/34 ARM: dts: sama7g5: add pit64b support

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Add DT bindings for PIT64B driver.

---
 arch/arm/dts/sama7g5.dtsi          | 8 ++++++++
 arch/arm/dts/sama7g5ek-u-boot.dtsi | 4 ++++
 2 files changed, 12 insertions(+)
arch/arm/dts/sama7g5.dtsi +8 -0
index a2554dcfff..f633c2f81e 100644
@@ -86,6 +86,14 @@
 				status = "disabled";
 			};
 
+			pit64b0: timer at e1800000 {
+				compatible = "microchip,sama7g5-pit64b";
+				reg = <0xe1800000 0x4000>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 70>, <&pmc PMC_TYPE_GCK 70>;
+				clock-names = "pclk", "gclk";
+				status = "okay";
+			};
+
 			uart0: serial at e1824200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xe1824200 0x200>;
arch/arm/dts/sama7g5ek-u-boot.dtsi +4 -0
index 95d9c3bff2..27e0f316f3 100644
@@ -31,6 +31,10 @@
 	u-boot,dm-pre-reloc;
 };
 
+&pit64b0 {
+	u-boot,dm-pre-reloc;
+};
+
 &pmc {
 	u-boot,dm-pre-reloc;
 };
Signature · 1 line
2.25.1
#17 lore raw

PATCH 17/34 ARM: dts: at91: sama7g5: add pinctrl node

In reply to Eugen Hristev

Add pioA pinctrl node.

---
 arch/arm/dts/sama7g5.dtsi          | 13 +++++++++++++
 arch/arm/dts/sama7g5ek-u-boot.dtsi |  8 ++++++++
 2 files changed, 21 insertions(+)
arch/arm/dts/sama7g5.dtsi +13 -0
index f633c2f81e..d9208d68d5 100644
@@ -62,6 +62,19 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 
+			pioA: pinctrl at e0014000 {
+				compatible = "atmel,sama5d2-gpio";
+				reg = <0xe0014000 0x800>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+				status = "okay";
+
+				pinctrl: pinctrl_default {
+					compatible = "microchip,sama7g5-pinctrl";
+				};
+			};
+
 			pmc: pmc at e0018000 {
 				compatible = "microchip,sama7g5-pmc";
 				reg = <0xe0018000 0x200>;
arch/arm/dts/sama7g5ek-u-boot.dtsi +8 -0
index 27e0f316f3..4af4d1bb5b 100644
@@ -31,6 +31,14 @@
 	u-boot,dm-pre-reloc;
 };
 
+&pioA {
+	u-boot,dm-pre-reloc;
+
+	pinctrl {
+		u-boot,dm-pre-reloc;
+	};
+};
+
 &pit64b0 {
 	u-boot,dm-pre-reloc;
 };
Signature · 1 line
2.25.1
#18 lore raw

PATCH 18/34 ARM: dts: at91: sama7g5ek: add pinctrl for sdmmc1 and flx3

In reply to Eugen Hristev

Add pinctrl for sdmmc1 and flx3.

---
 arch/arm/dts/sama7g5ek-u-boot.dtsi |  4 ++++
 arch/arm/dts/sama7g5ek.dts         | 30 ++++++++++++++++++++++++++++++
 2 files changed, 34 insertions(+)
arch/arm/dts/sama7g5ek-u-boot.dtsi +4 -0
index 4af4d1bb5b..5e1a0d53a5 100644
@@ -39,6 +39,10 @@
 	};
 };
 
+&pinctrl_flx3_default {
+	u-boot,dm-pre-reloc;
+};
+
 &pit64b0 {
 	u-boot,dm-pre-reloc;
 };
arch/arm/dts/sama7g5ek.dts +30 -0
index 03c7aa07ea..a9190bfcb3 100644
@@ -38,12 +38,42 @@
 		apb {
 			sdmmc1: sdio-host at e1208000 {
 				bus-width = <4>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_sdmmc1_cmd_data_default
+					     &pinctrl_sdmmc1_ck_cd_rstn_vddsel_default>;
 				status = "okay";
 			};
 
 			uart0: serial at e1824200 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_flx3_default>;
 				status = "okay";
 			};
 		};
 	};
 };
+
+&pinctrl {
+	pinctrl_flx3_default: flx3_default {
+		pinmux = <PIN_PD16__FLEXCOM3_IO0>,
+			 <PIN_PD17__FLEXCOM3_IO1>;
+		bias-disable;
+	};
+
+	pinctrl_sdmmc1_cmd_data_default: sdmmc1_cmd_data_default {
+		pinmux = <PIN_PB29__SDMMC1_CMD>,
+			 <PIN_PB31__SDMMC1_DAT0>,
+			 <PIN_PC0__SDMMC1_DAT1>,
+			 <PIN_PC1__SDMMC1_DAT2>,
+			 <PIN_PC2__SDMMC1_DAT3>;
+		bias-pull-up;
+	};
+
+	pinctrl_sdmmc1_ck_cd_rstn_vddsel_default: sdmmc1_ck_cd_rstn_vddsel_default {
+		pinmux = <PIN_PB30__SDMMC1_CK>,
+			 <PIN_PB28__SDMMC1_RSTN>,
+			 <PIN_PC5__SDMMC1_1V8SEL>,
+			 <PIN_PC4__SDMMC1_CD>;
+		bias-pull-up;
+	};
+};
Signature · 1 line
2.25.1
#19 lore raw

PATCH 19/34 configs: sama7g5ek: enable mii command

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Enable mii command as ethernet's PHY specific programming is based on it.

---
 configs/sama7g5ek_mmc1_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
index 99e2439516..176f4f3000 100644
@@ -29,6 +29,7 @@ CONFIG_CMD_I2C=y
 # CONFIG_CMD_LOADS is not set
 CONFIG_CMD_MMC=y
 CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_EXT4=y
 CONFIG_CMD_FAT=y
Signature · 1 line
2.25.1
#20 lore raw

PATCH 20/34 ARM: dts: sama7g5: add GMAC0

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Add GMAC0.

---
 arch/arm/dts/sama7g5.dtsi  | 11 +++++++++++
 arch/arm/dts/sama7g5ek.dts | 32 ++++++++++++++++++++++++++++++++
 2 files changed, 43 insertions(+)
arch/arm/dts/sama7g5.dtsi +11 -0
index d9208d68d5..33589f3ad9 100644
@@ -114,6 +114,17 @@
 				clock-names = "usart";
 				status = "disabled";
 			};
+
+			gmac0: ethernet at e2800000 {
+				compatible = "cdns,sama7g5-gem";
+				reg = <0xe2800000 0x4000>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_GCK 51>;
+				clock-names = "hclk", "pclk", "tx_clk";
+				assigned-clocks = <&pmc PMC_TYPE_GCK 51>;
+				assigned-clock-parents = <&pmc PMC_TYPE_CORE 21>; /* eth pll div. */
+				assigned-clock-rates = <125000000>;
+				status = "disabled";
+			};
 		};
 	};
 };
arch/arm/dts/sama7g5ek.dts +32 -0
index a9190bfcb3..194f4644b5 100644
@@ -53,6 +53,19 @@
 	};
 };
 
+&gmac0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gmac0_default>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	ethernet-phy at 7 {
+		reg = <0x7>;
+	};
+};
+
 &pinctrl {
 	pinctrl_flx3_default: flx3_default {
 		pinmux = <PIN_PD16__FLEXCOM3_IO0>,
@@ -76,4 +89,23 @@
 			 <PIN_PC4__SDMMC1_CD>;
 		bias-pull-up;
 	};
+
+	pinctrl_gmac0_default: gmac0_default {
+		pinmux = <PIN_PA16__G0_TX0>,
+			 <PIN_PA17__G0_TX1>,
+			 <PIN_PA26__G0_TX2>,
+			 <PIN_PA27__G0_TX3>,
+			 <PIN_PA19__G0_RX0>,
+			 <PIN_PA20__G0_RX1>,
+			 <PIN_PA28__G0_RX2>,
+			 <PIN_PA29__G0_RX3>,
+			 <PIN_PA15__G0_TXEN>,
+			 <PIN_PA24__G0_TXCK>,
+			 <PIN_PA30__G0_RXCK>,
+			 <PIN_PA18__G0_RXDV>,
+			 <PIN_PA22__G0_MDC>,
+			 <PIN_PA23__G0_MDIO>,
+			 <PIN_PA25__G0_125CK>;
+		bias-disable;
+	};
 };
Signature · 1 line
2.25.1
#21 lore raw

PATCH 21/34 ARM: dts: sama7g5: add GMAC1

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Add GMAC1.

---
 arch/arm/dts/sama7g5.dtsi  |  8 ++++++++
 arch/arm/dts/sama7g5ek.dts | 27 +++++++++++++++++++++++++++
 2 files changed, 35 insertions(+)
arch/arm/dts/sama7g5.dtsi +8 -0
index 33589f3ad9..43fac992ee 100644
@@ -125,6 +125,14 @@
 				assigned-clock-rates = <125000000>;
 				status = "disabled";
 			};
+
+			gmac1: ethernet at e2804000 {
+				compatible = "cdns,sama7g5-emac";
+				reg = <0xe2804000 0x1000>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 52>, <&pmc PMC_TYPE_PERIPHERAL 52>;
+				clock-names = "pclk", "hclk";
+				status = "disabled";
+			};
 		};
 	};
 };
arch/arm/dts/sama7g5ek.dts +27 -0
index 194f4644b5..3eac94896d 100644
@@ -66,6 +66,19 @@
 	};
 };
 
+&gmac1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gmac1_default>;
+	phy-mode = "rmii";
+	status = "okay";
+
+	ethernet-phy at 0 {
+		reg = <0x0>;
+	};
+};
+
 &pinctrl {
 	pinctrl_flx3_default: flx3_default {
 		pinmux = <PIN_PD16__FLEXCOM3_IO0>,
@@ -108,4 +121,18 @@
 			 <PIN_PA25__G0_125CK>;
 		bias-disable;
 	};
+
+	pinctrl_gmac1_default: gmac1_default {
+		pinmux = <PIN_PD30__G1_TXCK>,
+			 <PIN_PD22__G1_TX0>,
+			 <PIN_PD23__G1_TX1>,
+			 <PIN_PD21__G1_TXEN>,
+			 <PIN_PD25__G1_RX0>,
+			 <PIN_PD26__G1_RX1>,
+			 <PIN_PD27__G1_RXER>,
+			 <PIN_PD24__G1_RXDV>,
+			 <PIN_PD28__G1_MDC>,
+			 <PIN_PD29__G1_MDIO>;
+		bias-disable;
+	};
 };
Signature · 1 line
2.25.1
#22 lore raw

PATCH 22/34 board: atmel: sama7g5ek: increase arp timeout and retry count

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Increase ARP timeout and retry count as this will increase the speed of communication.

---
 include/configs/sama7g5ek.h | 3 +++
 1 file changed, 3 insertions(+)
include/configs/sama7g5ek.h +3 -0
index fbf0274b38..dc6cf4c700 100644
@@ -44,4 +44,7 @@
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
 
+#define CONFIG_ARP_TIMEOUT		200
+#define CONFIG_NET_RETRY_COUNT		50
+
 #endif
Signature · 1 line
2.25.1
#23 lore raw

PATCH 23/34 configs: sama7g5ek: enable support for KSZ9131

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Enable support for KSZ9131.

---
 configs/sama7g5ek_mmc1_defconfig | 2 ++
 1 file changed, 2 insertions(+)
configs/sama7g5ek_mmc1_defconfig +2 -0
index 176f4f3000..7e3cf49da0 100644
@@ -49,6 +49,8 @@ CONFIG_DM_I2C=y
 CONFIG_DM_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
 CONFIG_DM_ETH=y
 CONFIG_MACB=y
 CONFIG_PINCTRL=y
Signature · 1 line
2.25.1
#24 lore raw

PATCH 24/34 configs: sama7g5ek: enable CCF

In reply to Eugen Hristev

From: Claudiu Beznea <[email protected]>

Enable CCF for SAMA7G5.

---
 configs/sama7g5ek_mmc1_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
index 7e3cf49da0..fa4c88ffa6 100644
@@ -38,6 +38,7 @@ CONFIG_ENV_IS_IN_FAT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_DM=y
 CONFIG_CLK=y
+CONFIG_CLK_CCF=y
 CONFIG_CLK_AT91=y
 CONFIG_AT91_UTMI=y
 CONFIG_AT91_GENERIC_CLK=y
Signature · 1 line
2.25.1
#25 lore raw

PATCH 25/34 ARM: dts: at91: sama7g5: add assigned clocks for sdmmc1

In reply to Eugen Hristev

SDMMC1 requires clock specification with assigned-clocks, such that the PMC will know which parent to assign and the initial start-up frequency.

---
 arch/arm/dts/sama7g5.dtsi | 3 +++
 1 file changed, 3 insertions(+)
arch/arm/dts/sama7g5.dtsi +3 -0
index 43fac992ee..826828bb17 100644
@@ -96,6 +96,9 @@
 				reg = <0xe1208000 0x300>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 81>, <&pmc PMC_TYPE_GCK 81>;
 				clock-names = "hclock", "multclk";
+				assigned-clocks = <&pmc PMC_TYPE_GCK 81>;
+				assigned-clock-rates = <200000000>;
+				assigned-clock-parents = <&pmc PMC_TYPE_CORE 10>; /* sys pll div. */
 				status = "disabled";
 			};
 
Signature · 1 line
2.25.1
#26 lore raw

PATCH 26/34 ARM: dts: at91: sama7g5: add node for sdmmc0

In reply to Eugen Hristev

Add node for sdmmc0 block.

---
 arch/arm/dts/sama7g5.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm/dts/sama7g5.dtsi +11 -0
index 826828bb17..4c571befad 100644
@@ -91,6 +91,17 @@
 				#clock-cells = <1>;
 			};
 
+			sdmmc0: sdio-host at e1204000 {
+				compatible = "microchip,sama7g5-sdhci";
+				reg = <0xe1204000 0x300>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 80>, <&pmc PMC_TYPE_GCK 80>;
+				clock-names = "hclock", "multclk";
+				assigned-clocks = <&pmc PMC_TYPE_GCK 80>;
+				assigned-clock-rates = <200000000>;
+				assigned-clock-parents = <&pmc PMC_TYPE_CORE 10>; /* sys pll div. */
+				status = "disabled";
+			};
+
 			sdmmc1: sdio-host at e1208000 {
 				compatible = "microchip,sama7g5-sdhci";
 				reg = <0xe1208000 0x300>;
Signature · 1 line
2.25.1
#27 lore raw

PATCH 27/34 ARM: dts: at91: sama7g5ek: enable sdmmc0 with pinctrl

In reply to Eugen Hristev

Enable sdmmc0 on this board. A non-removable eMMC is connected on this block.
Configure pincontrol accordingly.

---
 arch/arm/dts/sama7g5ek.dts | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
arch/arm/dts/sama7g5ek.dts +30 -0
index 3eac94896d..452bf425df 100644
@@ -36,6 +36,15 @@
 	ahb {
 
 		apb {
+			sdmmc0: sdio-host at e1204000 {
+				bus-width = <8>;
+				non-removable;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_sdmmc0_cmd_data_default
+					     &pinctrl_sdmmc0_ck_rstn_ds_cd_default>;
+				status = "okay";
+			};
+
 			sdmmc1: sdio-host at e1208000 {
 				bus-width = <4>;
 				pinctrl-names = "default";
@@ -86,6 +95,27 @@
 		bias-disable;
 	};
 
+	pinctrl_sdmmc0_cmd_data_default: sdmmc0_cmd_data_default {
+		pinmux = <PIN_PA1__SDMMC0_CMD>,
+			 <PIN_PA3__SDMMC0_DAT0>,
+			 <PIN_PA4__SDMMC0_DAT1>,
+			 <PIN_PA5__SDMMC0_DAT2>,
+			 <PIN_PA6__SDMMC0_DAT3>,
+			 <PIN_PA7__SDMMC0_DAT4>,
+			 <PIN_PA8__SDMMC0_DAT5>,
+			 <PIN_PA9__SDMMC0_DAT6>,
+			 <PIN_PA10__SDMMC0_DAT7>;
+		bias-pull-up;
+	};
+
+	pinctrl_sdmmc0_ck_rstn_ds_cd_default: sdmmc0_ck_rstn_ds_cd_default {
+		pinmux = <PIN_PA0__SDMMC0_CK>,
+			 <PIN_PA2__SDMMC0_RSTN>,
+			 <PIN_PA11__SDMMC0_DS>,
+			 <PIN_PA14__SDMMC0_CD>;
+		bias-pull-up;
+	};
+
 	pinctrl_sdmmc1_cmd_data_default: sdmmc1_cmd_data_default {
 		pinmux = <PIN_PB29__SDMMC1_CMD>,
 			 <PIN_PB31__SDMMC1_DAT0>,
Signature · 1 line
2.25.1
#28 lore raw

PATCH 28/34 board: atmel: sama7g5ek: clean-up header bootcommand

In reply to Eugen Hristev

Clean-up boot command to use the predefined device and part for FAT environment.
According to this device and partition, select the proper boot media.

---
 include/configs/sama7g5ek.h | 11 +++--------
 1 file changed, 3 insertions(+), 8 deletions(-)
include/configs/sama7g5ek.h +3 -8
index dc6cf4c700..ef3bfa36fd 100644
@@ -29,16 +29,11 @@
 #undef CONFIG_BOOTCOMMAND
 #ifdef CONFIG_SD_BOOT
 /* u-boot env in sd/mmc card */
-#define FAT_ENV_INTERFACE	"mmc"
-#define FAT_ENV_DEVICE_AND_PART	"0"
-#define FAT_ENV_FILE		"uboot.env"
+
 /* bootstrap + u-boot + env in sd card */
-#define CONFIG_BOOTCOMMAND	"fatload mmc 0:1 0x61000000 at91-sama7g5ek.dtb; " \
-				"fatload mmc 0:1 0x62000000 zImage; " \
+#define CONFIG_BOOTCOMMAND	"fatload mmc " CONFIG_ENV_FAT_DEVICE_AND_PART " 0x61000000 at91-sama7g5ek.dtb; " \
+				"fatload mmc " CONFIG_ENV_FAT_DEVICE_AND_PART " 0x62000000 zImage; " \
 				"bootz 0x62000000 - 0x61000000"
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTARGS \
-	"console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"
 #endif
 
 /* Size of malloc() pool */
Signature · 1 line
2.25.1
#29 lore raw

PATCH 29/34 configs: sama7g5: add mmc config for sdmmc0

In reply to Eugen Hristev

Add new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

---
 board/atmel/sama7g5ek/MAINTAINERS |  1 +
 configs/sama7g5ek_mmc1_defconfig  |  7 ++--
 configs/sama7g5ek_mmc_defconfig   | 67 +++++++++++++++++++++++++++++++
 3 files changed, 72 insertions(+), 3 deletions(-)
 create mode 100644 configs/sama7g5ek_mmc_defconfig
board/atmel/sama7g5ek/MAINTAINERS +1 -0
index f66953ac4e..eac972968d 100644
@@ -4,4 +4,5 @@ S:     Maintained
 F:     board/atmel/sama7g5ek.c
 F:     include/configs/sama7g5ek.h
 F:     configs/sama7g5ek_mmc1_defconfig
+F:     configs/sama7g5ek_mmc_defconfig
 
configs/sama7g5ek_mmc1_defconfig +4 -3
index fa4c88ffa6..b6d2f4dd05 100644
@@ -2,9 +2,10 @@ CONFIG_ARM=y
 CONFIG_ARCH_AT91=y
 CONFIG_SYS_TEXT_BASE=0x66f00000
 CONFIG_TARGET_SAMA7G5EK=y
-CONFIG_NR_DRAM_BANKS=1
 CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
 CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
 CONFIG_DEBUG_UART_BOARD_INIT=y
 CONFIG_DEBUG_UART_BASE=0xe1824200
 CONFIG_DEBUG_UART_CLOCK=200000000
@@ -14,6 +15,7 @@ CONFIG_ENV_VARS_UBOOT_CONFIG=y
 CONFIG_FIT=y
 CONFIG_SD_BOOT=y
 CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait"
 CONFIG_MISC_INIT_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_BOOTZ=y
@@ -35,6 +37,7 @@ CONFIG_CMD_EXT4=y
 CONFIG_CMD_FAT=y
 CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_DM=y
 CONFIG_CLK=y
@@ -44,7 +47,6 @@ CONFIG_AT91_UTMI=y
 CONFIG_AT91_GENERIC_CLK=y
 CONFIG_AT91_SAM9X60_PLL=y
 CONFIG_CPU=y
-CONFIG_DM_GPIO=y
 CONFIG_ATMEL_PIO4=y
 CONFIG_DM_I2C=y
 CONFIG_DM_MMC=y
@@ -56,7 +58,6 @@ CONFIG_DM_ETH=y
 CONFIG_MACB=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_AT91PIO4=y
-# CONFIG_RAM_ROCKCHIP_DEBUG is not set
 CONFIG_DM_SERIAL=y
 CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_ATMEL_USART=y
configs/sama7g5ek_mmc_defconfig new file +67 -0

67 lines not on this page · raw message

Signature · 1 line
2.25.1
#37 lore raw

PATCH 30/34 ARM: dts: at91: sama7g5: add flexcom1 and i2c subnode

In reply to Eugen Hristev

Add flexcom1 and i2c subnode.

---
 arch/arm/dts/sama7g5.dtsi | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
arch/arm/dts/sama7g5.dtsi +17 -0
index 4c571befad..4846778ed9 100644
@@ -121,6 +121,23 @@
 				status = "okay";
 			};
 
+			flx1: flexcom at e181c000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xe181c000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xe181c000 0x800>;
+				status = "disabled";
+
+				i2c1: i2c at 600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+				};
+			};
 			uart0: serial at e1824200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xe1824200 0x200>;
Signature · 1 line
2.25.1
#38 lore raw

PATCH 31/34 ARM: dts: sama7g5ek: add i2c1 bus and eeproms

In reply to Eugen Hristev

Add node for flx1 i2c1 subnode (and alias to bus 0) This bus has two eeprom devices connected.

---
 arch/arm/dts/sama7g5ek.dts | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
arch/arm/dts/sama7g5ek.dts +30 -0
index 452bf425df..0812b0cc00 100644
@@ -17,6 +17,7 @@
 
 	aliases {
 		serial0 = &uart0;
+		i2c0 = &i2c1;
 	};
 
 	chosen {
@@ -62,6 +63,29 @@
 	};
 };
 
+&flx1 {
+	atmel,flexcom-mode = <3>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flx1_default>;
+	status = "okay";
+
+	eeprom at 52 {
+		compatible = "atmel,24c32";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	eeprom at 53 {
+		compatible = "atmel,24c32";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
 &gmac0 {
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -89,6 +113,12 @@
 };
 
 &pinctrl {
+	pinctrl_flx1_default: flx1_default {
+		pinmux = <PIN_PC9__FLEXCOM1_IO0>,
+			 <PIN_PC10__FLEXCOM1_IO1>;
+		bias-disable;
+	};
+
 	pinctrl_flx3_default: flx3_default {
 		pinmux = <PIN_PD16__FLEXCOM3_IO0>,
 			 <PIN_PD17__FLEXCOM3_IO1>;
Signature · 1 line
2.25.1
#39 lore raw

PATCH 32/34 board: atmel: sama7g5ek: add support for MAC address retreival

In reply to Eugen Hristev

Obtain two MAC addresses from the two EEPROMs and configure the two available Ethernet interfaces accordingly.

---
 board/atmel/sama7g5ek/sama7g5ek.c | 18 +++++++++++++-----
 1 file changed, 13 insertions(+), 5 deletions(-)
board/atmel/sama7g5ek/sama7g5ek.c +13 -5
index 1d7a01593d..ed1cf80da7 100644
@@ -46,6 +46,19 @@ int board_early_init_f(void)
 	return 0;
 }
 
+#define MAC24AA_MAC_OFFSET     0xfa
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+#ifdef CONFIG_I2C_EEPROM
+	at91_set_ethaddr(MAC24AA_MAC_OFFSET);
+	at91_set_eth1addr(MAC24AA_MAC_OFFSET);
+#endif
+	return 0;
+}
+#endif
+
 int board_init(void)
 {
 	/* address of boot parameters */
@@ -61,8 +74,3 @@ int dram_init(void)
 	return 0;
 }
 
-int misc_init_r(void)
-{
-	return 0;
-}
-
Signature · 1 line
2.25.1
#40 lore raw

PATCH 33/34 configs: sama7g5ek: add i2c and eeprom

In reply to Eugen Hristev

Add drivers for flexcom, i2c and eeproms

---
 configs/sama7g5ek_mmc1_defconfig | 3 +++
 configs/sama7g5ek_mmc_defconfig  | 3 +++
 2 files changed, 6 insertions(+)
configs/sama7g5ek_mmc1_defconfig +3 -0
index b6d2f4dd05..af362021b9 100644
@@ -49,6 +49,9 @@ CONFIG_AT91_SAM9X60_PLL=y
 CONFIG_CPU=y
 CONFIG_ATMEL_PIO4=y
 CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_AT91=y
+CONFIG_I2C_EEPROM=y
+CONFIG_MICROCHIP_FLEXCOM=y
 CONFIG_DM_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ATMEL=y
configs/sama7g5ek_mmc_defconfig +3 -0
index 894a64983f..bbd1a0c659 100644
@@ -49,6 +49,9 @@ CONFIG_AT91_SAM9X60_PLL=y
 CONFIG_CPU=y
 CONFIG_ATMEL_PIO4=y
 CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_AT91=y
+CONFIG_I2C_EEPROM=y
+CONFIG_MICROCHIP_FLEXCOM=y
 CONFIG_DM_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ATMEL=y
Signature · 1 line
2.25.1
#41 lore raw

PATCH 34/34 ARM: dts: sama7g5ek: fix TXC pin configuration

In reply to Eugen Hristev

From: Nicolas Ferre <[email protected]>

TXC line is directly connected from the SoC to the KSZ9131 PHY. There is a transient state on this signal, before configuring it to RGMII, which leads to packet transmit being blocked.
Keeping a pull-up when muxing this pin as function A (G0_TXCK) fixes the issue.

---
 arch/arm/dts/sama7g5ek.dts | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
arch/arm/dts/sama7g5ek.dts +6 -2
index 0812b0cc00..41818cc911 100644
@@ -90,7 +90,7 @@
 	#address-cells = <1>;
 	#size-cells = <0>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gmac0_default>;
+	pinctrl-0 = <&pinctrl_gmac0_default &pinctrl_gmac0_txc_default>;
 	phy-mode = "rgmii-id";
 	status = "okay";
 
@@ -173,7 +173,6 @@
 			 <PIN_PA28__G0_RX2>,
 			 <PIN_PA29__G0_RX3>,
 			 <PIN_PA15__G0_TXEN>,
-			 <PIN_PA24__G0_TXCK>,
 			 <PIN_PA30__G0_RXCK>,
 			 <PIN_PA18__G0_RXDV>,
 			 <PIN_PA22__G0_MDC>,
@@ -182,6 +181,11 @@
 		bias-disable;
 	};
 
+	pinctrl_gmac0_txc_default: gmac0_txc_default {
+		pinmux = <PIN_PA24__G0_TXCK>;
+		bias-pull-up;
+	};
+
 	pinctrl_gmac1_default: gmac1_default {
 		pinmux = <PIN_PD30__G1_TXCK>,
 			 <PIN_PD22__G1_TX0>,
Signature · 1 line
2.25.1
#30 lore raw

PATCH 29/34 configs: sama7g5: add mmc config for sdmmc0

In reply to Eugen Hristev

Hi,

Quoted 2 lines · Eugen Hristev

Add new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

Just one question, Sorry, i didn't check entire patchset.

What is different between sama7g5ek_mmc1 and sama7g5ek_mmc?

Best Regards,
Jaehoon Chung

Quoted 141 lines
---
 board/atmel/sama7g5ek/MAINTAINERS |  1 +
 configs/sama7g5ek_mmc1_defconfig  |  7 ++--
 configs/sama7g5ek_mmc_defconfig   | 67 +++++++++++++++++++++++++++++++
 3 files changed, 72 insertions(+), 3 deletions(-)
 create mode 100644 configs/sama7g5ek_mmc_defconfig
board/atmel/sama7g5ek/MAINTAINERS +1 -0
index f66953ac4e..eac972968d 100644
@@ -4,4 +4,5 @@ S:     Maintained
 F:     board/atmel/sama7g5ek.c
 F:     include/configs/sama7g5ek.h
 F:     configs/sama7g5ek_mmc1_defconfig
+F:     configs/sama7g5ek_mmc_defconfig
 
configs/sama7g5ek_mmc1_defconfig +4 -3
index fa4c88ffa6..b6d2f4dd05 100644
@@ -2,9 +2,10 @@ CONFIG_ARM=y
 CONFIG_ARCH_AT91=y
 CONFIG_SYS_TEXT_BASE=0x66f00000
 CONFIG_TARGET_SAMA7G5EK=y
-CONFIG_NR_DRAM_BANKS=1
 CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
 CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
 CONFIG_DEBUG_UART_BOARD_INIT=y
 CONFIG_DEBUG_UART_BASE=0xe1824200
 CONFIG_DEBUG_UART_CLOCK=200000000
@@ -14,6 +15,7 @@ CONFIG_ENV_VARS_UBOOT_CONFIG=y
 CONFIG_FIT=y
 CONFIG_SD_BOOT=y
 CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait"
 CONFIG_MISC_INIT_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_BOOTZ=y
@@ -35,6 +37,7 @@ CONFIG_CMD_EXT4=y
 CONFIG_CMD_FAT=y
 CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_DM=y
 CONFIG_CLK=y
@@ -44,7 +47,6 @@ CONFIG_AT91_UTMI=y
 CONFIG_AT91_GENERIC_CLK=y
 CONFIG_AT91_SAM9X60_PLL=y
 CONFIG_CPU=y
-CONFIG_DM_GPIO=y
 CONFIG_ATMEL_PIO4=y
 CONFIG_DM_I2C=y
 CONFIG_DM_MMC=y
@@ -56,7 +58,6 @@ CONFIG_DM_ETH=y
 CONFIG_MACB=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_AT91PIO4=y
-# CONFIG_RAM_ROCKCHIP_DEBUG is not set
 CONFIG_DM_SERIAL=y
 CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_ATMEL_USART=y
configs/sama7g5ek_mmc_defconfig new file +67 -0
new file mode 100644
index 0000000000..894a64983f
@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x66f00000
+CONFIG_TARGET_SAMA7G5EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xe1824200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEFAULT_DEVICE_TREE="sama7g5ek"
+CONFIG_DEBUG_UART=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_FIT=y
+CONFIG_SD_BOOT=y
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"
+CONFIG_MISC_INIT_R=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_MEMTEST_START=0x60000000
+CONFIG_SYS_MEMTEST_END=0x70000000
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_CCF=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_AT91_SAM9X60_PLL=y
+CONFIG_CPU=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_MCHP_PIT64B_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+# CONFIG_EFI_LOADER_HII is not set
#31 lore raw

PATCH 29/34 configs: sama7g5: add mmc config for sdmmc0

Quoted 9 lines · Jaehoon Chung

Hi,

Quoted 2 lines · Eugen Hristev

Add new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

Just one question, Sorry, i didn't check entire patchset.

What is different between sama7g5ek_mmc1 and sama7g5ek_mmc?

Sama7g5ek_mmc is set to store the environment in the eMMC device soldered on the board which is connected on the SDMMC0 hardware block.

sama7g5ek_mmc1 is set to store the environment on the SD-Card which can be inserted in the SD slot on the board which is connected on the SDMMC1 hardware block.

So basically we have two possible boot/env store configurations, one on eMMC and one on SD-Card .

Eugen

Quoted 146 lines

Best Regards,
Jaehoon Chung

Quoted 141 lines
---
  board/atmel/sama7g5ek/MAINTAINERS |  1 +
  configs/sama7g5ek_mmc1_defconfig  |  7 ++--
  configs/sama7g5ek_mmc_defconfig   | 67 +++++++++++++++++++++++++++++++
  3 files changed, 72 insertions(+), 3 deletions(-)

create mode 100644 configs/sama7g5ek_mmc_defconfig

board/atmel/sama7g5ek/MAINTAINERS +1 -0
index f66953ac4e..eac972968d 100644
@@ -4,4 +4,5 @@ S:     Maintained
  F:     board/atmel/sama7g5ek.c
  F:     include/configs/sama7g5ek.h
  F:     configs/sama7g5ek_mmc1_defconfig
+F:     configs/sama7g5ek_mmc_defconfig
 
configs/sama7g5ek_mmc1_defconfig +4 -3
index fa4c88ffa6..b6d2f4dd05 100644
@@ -2,9 +2,10 @@ CONFIG_ARM=y
  CONFIG_ARCH_AT91=y
  CONFIG_SYS_TEXT_BASE=0x66f00000
  CONFIG_TARGET_SAMA7G5EK=y
-CONFIG_NR_DRAM_BANKS=1
  CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
  CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
  CONFIG_DEBUG_UART_BOARD_INIT=y
  CONFIG_DEBUG_UART_BASE=0xe1824200
  CONFIG_DEBUG_UART_CLOCK=200000000
@@ -14,6 +15,7 @@ CONFIG_ENV_VARS_UBOOT_CONFIG=y
  CONFIG_FIT=y
  CONFIG_SD_BOOT=y
  CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait"
  CONFIG_MISC_INIT_R=y
  CONFIG_HUSH_PARSER=y
  CONFIG_CMD_BOOTZ=y
@@ -35,6 +37,7 @@ CONFIG_CMD_EXT4=y
  CONFIG_CMD_FAT=y
  CONFIG_OF_CONTROL=y
  CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
  CONFIG_SYS_RELOC_GD_ENV_ADDR=y
  CONFIG_DM=y
  CONFIG_CLK=y
@@ -44,7 +47,6 @@ CONFIG_AT91_UTMI=y
  CONFIG_AT91_GENERIC_CLK=y
  CONFIG_AT91_SAM9X60_PLL=y
  CONFIG_CPU=y
-CONFIG_DM_GPIO=y
  CONFIG_ATMEL_PIO4=y
  CONFIG_DM_I2C=y
  CONFIG_DM_MMC=y
@@ -56,7 +58,6 @@ CONFIG_DM_ETH=y
  CONFIG_MACB=y
  CONFIG_PINCTRL=y
  CONFIG_PINCTRL_AT91PIO4=y
-# CONFIG_RAM_ROCKCHIP_DEBUG is not set
  CONFIG_DM_SERIAL=y
  CONFIG_DEBUG_UART_ANNOUNCE=y
  CONFIG_ATMEL_USART=y
configs/sama7g5ek_mmc_defconfig new file +67 -0
new file mode 100644
index 0000000000..894a64983f
@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x66f00000
+CONFIG_TARGET_SAMA7G5EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xe1824200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEFAULT_DEVICE_TREE="sama7g5ek"
+CONFIG_DEBUG_UART=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_FIT=y
+CONFIG_SD_BOOT=y
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"
+CONFIG_MISC_INIT_R=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_MEMTEST_START=0x60000000
+CONFIG_SYS_MEMTEST_END=0x70000000
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_CCF=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_AT91_SAM9X60_PLL=y
+CONFIG_CPU=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_MCHP_PIT64B_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+# CONFIG_EFI_LOADER_HII is not set
#32 lore raw

PATCH 29/34 configs: sama7g5: add mmc config for sdmmc0

Quoted 14 lines · Eugen.Hristev at microchip.com
Quoted 9 lines · Jaehoon Chung

Hi,

Quoted 2 lines · Eugen Hristev

Add new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

Just one question, Sorry, i didn't check entire patchset.

What is different between sama7g5ek_mmc1 and sama7g5ek_mmc?

Sama7g5ek_mmc is set to store the environment in the eMMC device soldered on the board which is connected on the SDMMC0 hardware block.

Quoted 6 lines

sama7g5ek_mmc1 is set to store the environment on the SD-Card which can be inserted in the SD slot on the board which is connected on the SDMMC1 hardware block.

So basically we have two possible boot/env store configurations, one on eMMC and one on SD-Card .

If device can know which device is used to boot, then i think that it doesn't need to add one more config. It can know where env is stored at runtime.
(with CONFIG_ENV_FAT_DEVICE_AND_PART ":<partition>" and implement mmc_get_env_dev())

commit 6731bef6966ea2b26cdcfe0109ff5a950003fd03

Refs: v2020.07-1080-g6731bef696
Author:     David Woodhouse <[email protected]>
AuthorDate: Fri Jun 19 23:07:17 2020 +0100
Commit:     Tom Rini <[email protected]>
CommitDate: Sun Jul 26 14:35:12 2020 -0400

env/fat.c: allow loading from a FAT partition on the MMC boot device

I don't want to have to specify the device; only the partition.

This allows me to use the same image on internal eMMC or SD card for Banana Pi R2, and it finds its own environment either way.

[trini: Add #if/#else/#endif logic around CONFIG_SYS_MMC_ENV_DEV usage,
whitespace changes]

Best Regards,
Jaehoon Chung

Quoted 149 lines

Eugen

Quoted 146 lines

Best Regards,
Jaehoon Chung

Quoted 141 lines
---
  board/atmel/sama7g5ek/MAINTAINERS |  1 +
  configs/sama7g5ek_mmc1_defconfig  |  7 ++--
  configs/sama7g5ek_mmc_defconfig   | 67 +++++++++++++++++++++++++++++++
  3 files changed, 72 insertions(+), 3 deletions(-)

create mode 100644 configs/sama7g5ek_mmc_defconfig

board/atmel/sama7g5ek/MAINTAINERS +1 -0
index f66953ac4e..eac972968d 100644
@@ -4,4 +4,5 @@ S:     Maintained
  F:     board/atmel/sama7g5ek.c
  F:     include/configs/sama7g5ek.h
  F:     configs/sama7g5ek_mmc1_defconfig
+F:     configs/sama7g5ek_mmc_defconfig
 
configs/sama7g5ek_mmc1_defconfig +4 -3
index fa4c88ffa6..b6d2f4dd05 100644
@@ -2,9 +2,10 @@ CONFIG_ARM=y
  CONFIG_ARCH_AT91=y
  CONFIG_SYS_TEXT_BASE=0x66f00000
  CONFIG_TARGET_SAMA7G5EK=y
-CONFIG_NR_DRAM_BANKS=1
  CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
  CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
  CONFIG_DEBUG_UART_BOARD_INIT=y
  CONFIG_DEBUG_UART_BASE=0xe1824200
  CONFIG_DEBUG_UART_CLOCK=200000000
@@ -14,6 +15,7 @@ CONFIG_ENV_VARS_UBOOT_CONFIG=y
  CONFIG_FIT=y
  CONFIG_SD_BOOT=y
  CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait"
  CONFIG_MISC_INIT_R=y
  CONFIG_HUSH_PARSER=y
  CONFIG_CMD_BOOTZ=y
@@ -35,6 +37,7 @@ CONFIG_CMD_EXT4=y
  CONFIG_CMD_FAT=y
  CONFIG_OF_CONTROL=y
  CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
  CONFIG_SYS_RELOC_GD_ENV_ADDR=y
  CONFIG_DM=y
  CONFIG_CLK=y
@@ -44,7 +47,6 @@ CONFIG_AT91_UTMI=y
  CONFIG_AT91_GENERIC_CLK=y
  CONFIG_AT91_SAM9X60_PLL=y
  CONFIG_CPU=y
-CONFIG_DM_GPIO=y
  CONFIG_ATMEL_PIO4=y
  CONFIG_DM_I2C=y
  CONFIG_DM_MMC=y
@@ -56,7 +58,6 @@ CONFIG_DM_ETH=y
  CONFIG_MACB=y
  CONFIG_PINCTRL=y
  CONFIG_PINCTRL_AT91PIO4=y
-# CONFIG_RAM_ROCKCHIP_DEBUG is not set
  CONFIG_DM_SERIAL=y
  CONFIG_DEBUG_UART_ANNOUNCE=y
  CONFIG_ATMEL_USART=y
configs/sama7g5ek_mmc_defconfig new file +67 -0
new file mode 100644
index 0000000000..894a64983f
@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x66f00000
+CONFIG_TARGET_SAMA7G5EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xe1824200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEFAULT_DEVICE_TREE="sama7g5ek"
+CONFIG_DEBUG_UART=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_FIT=y
+CONFIG_SD_BOOT=y
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"
+CONFIG_MISC_INIT_R=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_MEMTEST_START=0x60000000
+CONFIG_SYS_MEMTEST_END=0x70000000
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_CCF=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_AT91_SAM9X60_PLL=y
+CONFIG_CPU=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_MCHP_PIT64B_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+# CONFIG_EFI_LOADER_HII is not set
#33 lore raw

PATCH 29/34 configs: sama7g5: add mmc config for sdmmc0

Quoted 21 lines · Jaehoon Chung

EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe

Quoted 18 lines · Eugen.Hristev at microchip.com
Quoted 9 lines · Jaehoon Chung

Hi,

Quoted 2 lines · Eugen Hristev

Add new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

Just one question, Sorry, i didn't check entire patchset.

What is different between sama7g5ek_mmc1 and sama7g5ek_mmc?

Sama7g5ek_mmc is set to store the environment in the eMMC device soldered on the board which is connected on the SDMMC0 hardware block.

sama7g5ek_mmc1 is set to store the environment on the SD-Card which can be inserted in the SD slot on the board which is connected on the SDMMC1 hardware block.

Quoted 7 lines
Quoted 2 lines

So basically we have two possible boot/env store configurations, one on eMMC and one on SD-Card .

If device can know which device is used to boot, then i think that it doesn't need to add one more config. It can know where env is stored at runtime.
(with CONFIG_ENV_FAT_DEVICE_AND_PART ":<partition>" and implement mmc_get_env_dev())

Can you explain a little more ? I do not understand how. How will u-boot know if it should read the env from SD or eMMC ?

Quoted 174 lines

commit 6731bef6966ea2b26cdcfe0109ff5a950003fd03

Refs: v2020.07-1080-g6731bef696
Author:     David Woodhouse <[email protected]>
AuthorDate: Fri Jun 19 23:07:17 2020 +0100
Commit:     Tom Rini <[email protected]>
CommitDate: Sun Jul 26 14:35:12 2020 -0400

env/fat.c: allow loading from a FAT partition on the MMC boot device

I don't want to have to specify the device; only the partition.

This allows me to use the same image on internal eMMC or SD card for Banana Pi R2, and it finds its own environment either way.

[trini: Add #if/#else/#endif logic around CONFIG_SYS_MMC_ENV_DEV usage,
whitespace changes]

Best Regards,
Jaehoon Chung

Quoted 149 lines

Eugen

Quoted 146 lines

Best Regards,
Jaehoon Chung

Quoted 141 lines
---
   board/atmel/sama7g5ek/MAINTAINERS |  1 +
   configs/sama7g5ek_mmc1_defconfig  |  7 ++--
   configs/sama7g5ek_mmc_defconfig   | 67 +++++++++++++++++++++++++++++++
   3 files changed, 72 insertions(+), 3 deletions(-)

create mode 100644 configs/sama7g5ek_mmc_defconfig

board/atmel/sama7g5ek/MAINTAINERS +1 -0
index f66953ac4e..eac972968d 100644
@@ -4,4 +4,5 @@ S:     Maintained
   F:     board/atmel/sama7g5ek.c
   F:     include/configs/sama7g5ek.h
   F:     configs/sama7g5ek_mmc1_defconfig
+F:     configs/sama7g5ek_mmc_defconfig
 
configs/sama7g5ek_mmc1_defconfig +4 -3
index fa4c88ffa6..b6d2f4dd05 100644
@@ -2,9 +2,10 @@ CONFIG_ARM=y
   CONFIG_ARCH_AT91=y
   CONFIG_SYS_TEXT_BASE=0x66f00000
   CONFIG_TARGET_SAMA7G5EK=y
-CONFIG_NR_DRAM_BANKS=1
   CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
   CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
   CONFIG_DEBUG_UART_BOARD_INIT=y
   CONFIG_DEBUG_UART_BASE=0xe1824200
   CONFIG_DEBUG_UART_CLOCK=200000000
@@ -14,6 +15,7 @@ CONFIG_ENV_VARS_UBOOT_CONFIG=y
   CONFIG_FIT=y
   CONFIG_SD_BOOT=y
   CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait"
   CONFIG_MISC_INIT_R=y
   CONFIG_HUSH_PARSER=y
   CONFIG_CMD_BOOTZ=y
@@ -35,6 +37,7 @@ CONFIG_CMD_EXT4=y
   CONFIG_CMD_FAT=y
   CONFIG_OF_CONTROL=y
   CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
   CONFIG_SYS_RELOC_GD_ENV_ADDR=y
   CONFIG_DM=y
   CONFIG_CLK=y
@@ -44,7 +47,6 @@ CONFIG_AT91_UTMI=y
   CONFIG_AT91_GENERIC_CLK=y
   CONFIG_AT91_SAM9X60_PLL=y
   CONFIG_CPU=y
-CONFIG_DM_GPIO=y
   CONFIG_ATMEL_PIO4=y
   CONFIG_DM_I2C=y
   CONFIG_DM_MMC=y
@@ -56,7 +58,6 @@ CONFIG_DM_ETH=y
   CONFIG_MACB=y
   CONFIG_PINCTRL=y
   CONFIG_PINCTRL_AT91PIO4=y
-# CONFIG_RAM_ROCKCHIP_DEBUG is not set
   CONFIG_DM_SERIAL=y
   CONFIG_DEBUG_UART_ANNOUNCE=y
   CONFIG_ATMEL_USART=y
configs/sama7g5ek_mmc_defconfig new file +67 -0
new file mode 100644
index 0000000000..894a64983f
@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x66f00000
+CONFIG_TARGET_SAMA7G5EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xe1824200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEFAULT_DEVICE_TREE="sama7g5ek"
+CONFIG_DEBUG_UART=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_FIT=y
+CONFIG_SD_BOOT=y
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"
+CONFIG_MISC_INIT_R=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_MEMTEST_START=0x60000000
+CONFIG_SYS_MEMTEST_END=0x70000000
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_CCF=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_AT91_SAM9X60_PLL=y
+CONFIG_CPU=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_MCHP_PIT64B_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+# CONFIG_EFI_LOADER_HII is not set
#34 lore raw

PATCH 29/34 configs: sama7g5: add mmc config for sdmmc0

Hi,

Quoted 25 lines · Eugen.Hristev at microchip.com
Quoted 24 lines · Jaehoon Chung

EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe

Quoted 20 lines · Eugen.Hristev at microchip.com
Quoted 9 lines · Jaehoon Chung

Hi,

Quoted 2 lines · Eugen Hristev

Add new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

Just one question, Sorry, i didn't check entire patchset.

What is different between sama7g5ek_mmc1 and sama7g5ek_mmc?

Sama7g5ek_mmc is set to store the environment in the eMMC device soldered on the board which is connected on the SDMMC0 hardware block.

sama7g5ek_mmc1 is set to store the environment on the SD-Card which can be inserted in the SD slot on the board which is connected on the SDMMC1 hardware block.

So basically we have two possible boot/env store configurations, one on eMMC and one on SD-Card .

Quoted 7 lines
Quoted 4 lines

If device can know which device is used to boot, then i think that it doesn't need to add one more config. It can know where env is stored at runtime.
(with CONFIG_ENV_FAT_DEVICE_AND_PART ":<partition>" and implement mmc_get_env_dev())

Can you explain a little more ? I do not understand how. How will u-boot know if it should read the env from SD or eMMC ?

I don't have any knowledge of your SoC. Maybe you know more exactly.
If its SoC has some registers to get boot device, it's possible to get which device is used to boot device. Then you can implement mmc_get_env_dev() in its board specific file.
Then it can be got with below sequence.
In env/fat.c
env_fat_devc_and_part()
-> part_str[0] += mmc_get_env_dev()
-> mmc_get_env_dev() will be returned to proper device after read register relevant to checking device.

If there is no register to get boot device, it may be impossible.

Best Regards,
Jaehoon Chung

Quoted 176 lines
Quoted 175 lines

commit 6731bef6966ea2b26cdcfe0109ff5a950003fd03

Refs: v2020.07-1080-g6731bef696
Author:     David Woodhouse <[email protected]>
AuthorDate: Fri Jun 19 23:07:17 2020 +0100
Commit:     Tom Rini <[email protected]>
CommitDate: Sun Jul 26 14:35:12 2020 -0400

env/fat.c: allow loading from a FAT partition on the MMC boot device

I don't want to have to specify the device; only the partition.

This allows me to use the same image on internal eMMC or SD card for Banana Pi R2, and it finds its own environment either way.

[trini: Add #if/#else/#endif logic around CONFIG_SYS_MMC_ENV_DEV usage,
whitespace changes]

Best Regards,
Jaehoon Chung

Quoted 149 lines

Eugen

Quoted 146 lines

Best Regards,
Jaehoon Chung

Quoted 141 lines
---
   board/atmel/sama7g5ek/MAINTAINERS |  1 +
   configs/sama7g5ek_mmc1_defconfig  |  7 ++--
   configs/sama7g5ek_mmc_defconfig   | 67 +++++++++++++++++++++++++++++++
   3 files changed, 72 insertions(+), 3 deletions(-)

create mode 100644 configs/sama7g5ek_mmc_defconfig

board/atmel/sama7g5ek/MAINTAINERS +1 -0
index f66953ac4e..eac972968d 100644
@@ -4,4 +4,5 @@ S:     Maintained
   F:     board/atmel/sama7g5ek.c
   F:     include/configs/sama7g5ek.h
   F:     configs/sama7g5ek_mmc1_defconfig
+F:     configs/sama7g5ek_mmc_defconfig
 
configs/sama7g5ek_mmc1_defconfig +4 -3
index fa4c88ffa6..b6d2f4dd05 100644
@@ -2,9 +2,10 @@ CONFIG_ARM=y
   CONFIG_ARCH_AT91=y
   CONFIG_SYS_TEXT_BASE=0x66f00000
   CONFIG_TARGET_SAMA7G5EK=y
-CONFIG_NR_DRAM_BANKS=1
   CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
   CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
   CONFIG_DEBUG_UART_BOARD_INIT=y
   CONFIG_DEBUG_UART_BASE=0xe1824200
   CONFIG_DEBUG_UART_CLOCK=200000000
@@ -14,6 +15,7 @@ CONFIG_ENV_VARS_UBOOT_CONFIG=y
   CONFIG_FIT=y
   CONFIG_SD_BOOT=y
   CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait"
   CONFIG_MISC_INIT_R=y
   CONFIG_HUSH_PARSER=y
   CONFIG_CMD_BOOTZ=y
@@ -35,6 +37,7 @@ CONFIG_CMD_EXT4=y
   CONFIG_CMD_FAT=y
   CONFIG_OF_CONTROL=y
   CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
   CONFIG_SYS_RELOC_GD_ENV_ADDR=y
   CONFIG_DM=y
   CONFIG_CLK=y
@@ -44,7 +47,6 @@ CONFIG_AT91_UTMI=y
   CONFIG_AT91_GENERIC_CLK=y
   CONFIG_AT91_SAM9X60_PLL=y
   CONFIG_CPU=y
-CONFIG_DM_GPIO=y
   CONFIG_ATMEL_PIO4=y
   CONFIG_DM_I2C=y
   CONFIG_DM_MMC=y
@@ -56,7 +58,6 @@ CONFIG_DM_ETH=y
   CONFIG_MACB=y
   CONFIG_PINCTRL=y
   CONFIG_PINCTRL_AT91PIO4=y
-# CONFIG_RAM_ROCKCHIP_DEBUG is not set
   CONFIG_DM_SERIAL=y
   CONFIG_DEBUG_UART_ANNOUNCE=y
   CONFIG_ATMEL_USART=y
configs/sama7g5ek_mmc_defconfig new file +67 -0
new file mode 100644
index 0000000000..894a64983f
@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x66f00000
+CONFIG_TARGET_SAMA7G5EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xe1824200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEFAULT_DEVICE_TREE="sama7g5ek"
+CONFIG_DEBUG_UART=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_FIT=y
+CONFIG_SD_BOOT=y
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"
+CONFIG_MISC_INIT_R=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_MEMTEST_START=0x60000000
+CONFIG_SYS_MEMTEST_END=0x70000000
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_CCF=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_AT91_SAM9X60_PLL=y
+CONFIG_CPU=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_MCHP_PIT64B_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+# CONFIG_EFI_LOADER_HII is not set
#35 lore raw

PATCH 29/34 configs: sama7g5: add mmc config for sdmmc0

Quoted 33 lines · Jaehoon Chung

Hi,

Quoted 30 lines · Eugen.Hristev at microchip.com
Quoted 28 lines · Jaehoon Chung

EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe

Quoted 14 lines · Eugen.Hristev at microchip.com
Quoted 9 lines · Jaehoon Chung

Hi,

Quoted 2 lines · Eugen Hristev

Add new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

Just one question, Sorry, i didn't check entire patchset.

What is different between sama7g5ek_mmc1 and sama7g5ek_mmc?

Sama7g5ek_mmc is set to store the environment in the eMMC device soldered on the board which is connected on the SDMMC0 hardware block.

Quoted 6 lines

sama7g5ek_mmc1 is set to store the environment on the SD-Card which can be inserted in the SD slot on the board which is connected on the SDMMC1 hardware block.

So basically we have two possible boot/env store configurations, one on eMMC and one on SD-Card .

If device can know which device is used to boot, then i think that it doesn't need to add one more config. It can know where env is stored at runtime.
(with CONFIG_ENV_FAT_DEVICE_AND_PART ":<partition>" and implement mmc_get_env_dev())

Quoted 5 lines
Quoted 2 lines

Can you explain a little more ? I do not understand how. How will u-boot know if it should read the env from SD or eMMC ?

I don't have any knowledge of your SoC. Maybe you know more exactly.
If its SoC has some registers to get boot device, it's possible to get which device is used to boot device.

It does, but U-boot is not the first stage bootloader. We have a second stage that initializes the external RAM first.
U-boot is in fact the third stage.

Quoted 8 lines

Then you can implement mmc_get_env_dev() in its board specific file.
Then it can be got with below sequence.
In env/fat.c
env_fat_devc_and_part()
-> part_str[0] += mmc_get_env_dev()
-> mmc_get_env_dev() will be returned to proper device after read register relevant to checking device.

If there is no register to get boot device, it may be impossible.

Even if we know the boot device, we do not wish do enforce u-boot to store the env on the same boot device. This would mean hard rules on storing the env, which is something we wish to avoid.
We would like to be able to select at compile time where to store the env and the default boot device. This would allow for example to have a very fast and small QSPI memory for storing the initial stages , but have u-boot load linux and store the env from/on eMMCs or SD-Cards.

Quoted 182 lines

Best Regards,
Jaehoon Chung

Quoted 176 lines
Quoted 175 lines

commit 6731bef6966ea2b26cdcfe0109ff5a950003fd03

Refs: v2020.07-1080-g6731bef696
Author:     David Woodhouse <[email protected]>
AuthorDate: Fri Jun 19 23:07:17 2020 +0100
Commit:     Tom Rini <[email protected]>
CommitDate: Sun Jul 26 14:35:12 2020 -0400

env/fat.c: allow loading from a FAT partition on the MMC boot device

I don't want to have to specify the device; only the partition.

This allows me to use the same image on internal eMMC or SD card for Banana Pi R2, and it finds its own environment either way.

[trini: Add #if/#else/#endif logic around CONFIG_SYS_MMC_ENV_DEV usage,
whitespace changes]

Best Regards,
Jaehoon Chung

Quoted 149 lines

Eugen

Quoted 146 lines

Best Regards,
Jaehoon Chung

Quoted 141 lines
---
    board/atmel/sama7g5ek/MAINTAINERS |  1 +
    configs/sama7g5ek_mmc1_defconfig  |  7 ++--
    configs/sama7g5ek_mmc_defconfig   | 67 +++++++++++++++++++++++++++++++
    3 files changed, 72 insertions(+), 3 deletions(-)

create mode 100644 configs/sama7g5ek_mmc_defconfig

board/atmel/sama7g5ek/MAINTAINERS +1 -0
index f66953ac4e..eac972968d 100644
@@ -4,4 +4,5 @@ S:     Maintained
    F:     board/atmel/sama7g5ek.c
    F:     include/configs/sama7g5ek.h
    F:     configs/sama7g5ek_mmc1_defconfig
+F:     configs/sama7g5ek_mmc_defconfig
 
configs/sama7g5ek_mmc1_defconfig +4 -3
index fa4c88ffa6..b6d2f4dd05 100644
@@ -2,9 +2,10 @@ CONFIG_ARM=y
    CONFIG_ARCH_AT91=y
    CONFIG_SYS_TEXT_BASE=0x66f00000
    CONFIG_TARGET_SAMA7G5EK=y
-CONFIG_NR_DRAM_BANKS=1
    CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
    CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
    CONFIG_DEBUG_UART_BOARD_INIT=y
    CONFIG_DEBUG_UART_BASE=0xe1824200
    CONFIG_DEBUG_UART_CLOCK=200000000
@@ -14,6 +15,7 @@ CONFIG_ENV_VARS_UBOOT_CONFIG=y
    CONFIG_FIT=y
    CONFIG_SD_BOOT=y
    CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait"
    CONFIG_MISC_INIT_R=y
    CONFIG_HUSH_PARSER=y
    CONFIG_CMD_BOOTZ=y
@@ -35,6 +37,7 @@ CONFIG_CMD_EXT4=y
    CONFIG_CMD_FAT=y
    CONFIG_OF_CONTROL=y
    CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
    CONFIG_SYS_RELOC_GD_ENV_ADDR=y
    CONFIG_DM=y
    CONFIG_CLK=y
@@ -44,7 +47,6 @@ CONFIG_AT91_UTMI=y
    CONFIG_AT91_GENERIC_CLK=y
    CONFIG_AT91_SAM9X60_PLL=y
    CONFIG_CPU=y
-CONFIG_DM_GPIO=y
    CONFIG_ATMEL_PIO4=y
    CONFIG_DM_I2C=y
    CONFIG_DM_MMC=y
@@ -56,7 +58,6 @@ CONFIG_DM_ETH=y
    CONFIG_MACB=y
    CONFIG_PINCTRL=y
    CONFIG_PINCTRL_AT91PIO4=y
-# CONFIG_RAM_ROCKCHIP_DEBUG is not set
    CONFIG_DM_SERIAL=y
    CONFIG_DEBUG_UART_ANNOUNCE=y
    CONFIG_ATMEL_USART=y
configs/sama7g5ek_mmc_defconfig new file +67 -0
new file mode 100644
index 0000000000..894a64983f
@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x66f00000
+CONFIG_TARGET_SAMA7G5EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xe1824200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEFAULT_DEVICE_TREE="sama7g5ek"
+CONFIG_DEBUG_UART=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_FIT=y
+CONFIG_SD_BOOT=y
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"
+CONFIG_MISC_INIT_R=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_MEMTEST_START=0x60000000
+CONFIG_SYS_MEMTEST_END=0x70000000
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_CCF=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_AT91_SAM9X60_PLL=y
+CONFIG_CPU=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_MCHP_PIT64B_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+# CONFIG_EFI_LOADER_HII is not set
#36 lore raw

PATCH 29/34 configs: sama7g5: add mmc config for sdmmc0

Quoted 37 lines · Eugen.Hristev at microchip.com
Quoted 36 lines · Jaehoon Chung

Hi,

Quoted 32 lines · Eugen.Hristev at microchip.com
Quoted 21 lines · Jaehoon Chung

EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe

Quoted 18 lines · Eugen.Hristev at microchip.com
Quoted 9 lines · Jaehoon Chung

Hi,

Quoted 2 lines · Eugen Hristev

Add new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

Just one question, Sorry, i didn't check entire patchset.

What is different between sama7g5ek_mmc1 and sama7g5ek_mmc?

Sama7g5ek_mmc is set to store the environment in the eMMC device soldered on the board which is connected on the SDMMC0 hardware block.

sama7g5ek_mmc1 is set to store the environment on the SD-Card which can be inserted in the SD slot on the board which is connected on the SDMMC1 hardware block.

Quoted 7 lines
Quoted 2 lines

So basically we have two possible boot/env store configurations, one on eMMC and one on SD-Card .

If device can know which device is used to boot, then i think that it doesn't need to add one more config. It can know where env is stored at runtime.
(with CONFIG_ENV_FAT_DEVICE_AND_PART ":<partition>" and implement mmc_get_env_dev())

Can you explain a little more ? I do not understand how. How will u-boot know if it should read the env from SD or eMMC ?

Quoted 6 lines
Quoted 2 lines

I don't have any knowledge of your SoC. Maybe you know more exactly.
If its SoC has some registers to get boot device, it's possible to get which device is used to boot device.

It does, but U-boot is not the first stage bootloader. We have a second stage that initializes the external RAM first.
U-boot is in fact the third stage.

It doesn't matter which stage is used. It's dependent with your register. If your bl0 is checking which device is used, it can be set to register.
- I don't know how to implement your bl0..so it's just guessing.

Quoted 8 lines
Quoted 8 lines

Then you can implement mmc_get_env_dev() in its board specific file.
Then it can be got with below sequence.
In env/f
env_fat_devc_and_part()
-> part_str[0] += mmc_get_env_dev()
-> mmc_get_env_dev() will be returned to proper device after read register relevant to checking device.

Quoted 5 lines
Quoted 1 line

If there is no register to get boot device, it may be impossible.

Even if we know the boot device, we do not wish do enforce u-boot to store the env on the same boot device. This would mean hard rules on storing the env, which is something we wish to avoid.

I understood what you want.
As i already mentioned, i didn't check this patchset fully. Just it seemed taht your configuration is duplicated, except env location. I don't have any objection about your patch. :)
Just had a question whether it can be used one config or not.

Thanks for explanation kindly.

Best Regards,
Jaehoon Chung

Quoted 187 lines

We would like to be able to select at compile time where to store the env and the default boot device. This would allow for example to have a very fast and small QSPI memory for storing the initial stages , but have u-boot load linux and store the env from/on eMMCs or SD-Cards.

Quoted 182 lines

Best Regards,
Jaehoon Chung

Quoted 176 lines
Quoted 175 lines

commit 6731bef6966ea2b26cdcfe0109ff5a950003fd03

Refs: v2020.07-1080-g6731bef696
Author:     David Woodhouse <[email protected]>
AuthorDate: Fri Jun 19 23:07:17 2020 +0100
Commit:     Tom Rini <[email protected]>
CommitDate: Sun Jul 26 14:35:12 2020 -0400

env/fat.c: allow loading from a FAT partition on the MMC boot device

I don't want to have to specify the device; only the partition.

This allows me to use the same image on internal eMMC or SD card for Banana Pi R2, and it finds its own environment either way.

[trini: Add #if/#else/#endif logic around CONFIG_SYS_MMC_ENV_DEV usage,
whitespace changes]

Best Regards,
Jaehoon Chung

Quoted 149 lines

Eugen

Quoted 146 lines

Best Regards,
Jaehoon Chung

Quoted 141 lines
---
    board/atmel/sama7g5ek/MAINTAINERS |  1 +
    configs/sama7g5ek_mmc1_defconfig  |  7 ++--
    configs/sama7g5ek_mmc_defconfig   | 67 +++++++++++++++++++++++++++++++
    3 files changed, 72 insertions(+), 3 deletions(-)

create mode 100644 configs/sama7g5ek_mmc_defconfig

board/atmel/sama7g5ek/MAINTAINERS +1 -0
index f66953ac4e..eac972968d 100644
@@ -4,4 +4,5 @@ S:     Maintained
    F:     board/atmel/sama7g5ek.c
    F:     include/configs/sama7g5ek.h
    F:     configs/sama7g5ek_mmc1_defconfig
+F:     configs/sama7g5ek_mmc_defconfig
 
configs/sama7g5ek_mmc1_defconfig +4 -3
index fa4c88ffa6..b6d2f4dd05 100644
@@ -2,9 +2,10 @@ CONFIG_ARM=y
    CONFIG_ARCH_AT91=y
    CONFIG_SYS_TEXT_BASE=0x66f00000
    CONFIG_TARGET_SAMA7G5EK=y
-CONFIG_NR_DRAM_BANKS=1
    CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
    CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
    CONFIG_DEBUG_UART_BOARD_INIT=y
    CONFIG_DEBUG_UART_BASE=0xe1824200
    CONFIG_DEBUG_UART_CLOCK=200000000
@@ -14,6 +15,7 @@ CONFIG_ENV_VARS_UBOOT_CONFIG=y
    CONFIG_FIT=y
    CONFIG_SD_BOOT=y
    CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait"
    CONFIG_MISC_INIT_R=y
    CONFIG_HUSH_PARSER=y
    CONFIG_CMD_BOOTZ=y
@@ -35,6 +37,7 @@ CONFIG_CMD_EXT4=y
    CONFIG_CMD_FAT=y
    CONFIG_OF_CONTROL=y
    CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
    CONFIG_SYS_RELOC_GD_ENV_ADDR=y
    CONFIG_DM=y
    CONFIG_CLK=y
@@ -44,7 +47,6 @@ CONFIG_AT91_UTMI=y
    CONFIG_AT91_GENERIC_CLK=y
    CONFIG_AT91_SAM9X60_PLL=y
    CONFIG_CPU=y
-CONFIG_DM_GPIO=y
    CONFIG_ATMEL_PIO4=y
    CONFIG_DM_I2C=y
    CONFIG_DM_MMC=y
@@ -56,7 +58,6 @@ CONFIG_DM_ETH=y
    CONFIG_MACB=y
    CONFIG_PINCTRL=y
    CONFIG_PINCTRL_AT91PIO4=y
-# CONFIG_RAM_ROCKCHIP_DEBUG is not set
    CONFIG_DM_SERIAL=y
    CONFIG_DEBUG_UART_ANNOUNCE=y
    CONFIG_ATMEL_USART=y
configs/sama7g5ek_mmc_defconfig new file +67 -0
new file mode 100644
index 0000000000..894a64983f
@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_SYS_TEXT_BASE=0x66f00000
+CONFIG_TARGET_SAMA7G5EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x11000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x4000
+CONFIG_DM_GPIO=y
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xe1824200
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEFAULT_DEVICE_TREE="sama7g5ek"
+CONFIG_DEBUG_UART=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_FIT=y
+CONFIG_SD_BOOT=y
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"
+CONFIG_MISC_INIT_R=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_MEMTEST_START=0x60000000
+CONFIG_SYS_MEMTEST_END=0x70000000
+CONFIG_CMD_STRINGS=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_CCF=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_AT91_SAM9X60_PLL=y
+CONFIG_CPU=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_MCHP_PIT64B_TIMER=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+# CONFIG_EFI_LOADER_HII is not set