Skip to contentSkip to conversation

stm32mp1: modify gpt partitions to fix BSP update

RFC PATCH New Sergey Matyukevich 3 participants 6 messages Jan 30, 2021 – Feb 7, 2021 Arm STM32

lore
Share & tools
lore
#0 lore raw

RFC PATCH 1/1 stm32mp1: modify gpt partitions to fix BSP update

Hi all,

BSP update for stm32mp1 boards does not work right out of the box. The first boot is ok, but the second boot fails:

NOTICE:  CPU: STM32MP157CAC Rev.B
NOTICE:  Model: STMicroelectronics STM32MP157C-DK2 Discovery Board
NOTICE:  Board: MB1272 Var2.0 Rev.C-01
NOTICE:  BL2: v2.4(release):2020.11-1087-g8fac193e6d-dirty
NOTICE:  BL2: Built : 20:58:09, Jan 27 2021
ERROR:   Checksum: 0x5023a37 (awaited: 0x5046ea4)
ERROR:   Header check failed
ERROR:   BL2: Failed to load image id 5 (-12)

The root cause is in changes for stm32mp1 trusted defconfig in updated
U-Boot: see U-Boot commit 76db1681da52 ("stm32mp1: use a specific SD/eMMC partition for U-Boot enviromnent"). Starting from that commit, U-Boot environment is stored at the end of the U-Boot partition. As a result, saving environment changes GPT partition checksum verified by ATF.

IIUC at least the following two approaches can be implemented to make updated BSP work smoothly.

The first approach is to modify U-Boot config fragment for stm32mp1 boards and to re-enable saving U-Boot environment on ext4. However this choice implies certain restriction on rootfs ext4 features since it should be writable by U-Boot. See the mentioned U-Boot commit message for details.

Another approach is implemented by the attached patch: keep U-Boot environment on a dedicated GPT partition.

Thoughts ? Comments ?

Regards,
Sergey

---
 .../common/stm32mp157/genimage.cfg.template         |  4 ++++
 .../overlay/boot/extlinux/extlinux.conf             |  2 +-
 .../uboot/0001-uboot-stm32mp1-uboot-env.patch       | 13 +++++++++++++
 .../overlay/boot/extlinux/extlinux.conf             |  2 +-
 .../uboot/0001-uboot-stm32mp1-uboot-env.patch       | 13 +++++++++++++
 configs/stm32mp157a_dk1_defconfig                   |  9 +++++----
 configs/stm32mp157c_dk2_defconfig                   |  9 +++++----
 7 files changed, 42 insertions(+), 10 deletions(-)
 create mode 100644 board/stmicroelectronics/stm32mp157a-dk1/patches/uboot/0001-uboot-stm32mp1-uboot-env.patch
 create mode 100644 board/stmicroelectronics/stm32mp157c-dk2/patches/uboot/0001-uboot-stm32mp1-uboot-env.patch
board/stmicroelectronics/common/stm32mp157/genimage.cfg.template +4 -0
index f341c19f2f..12f79efa90 100644
@@ -15,6 +15,10 @@ image sdcard.img {
 		image = "u-boot.stm32"
 	}
 
+	partition env {
+		size = 16K
+	}
+
 	partition rootfs {
 		image = "rootfs.ext4"
 		bootable = "yes"
board/stmicroelectronics/stm32mp157a-dk1/overlay/boot/extlinux/extlinux.conf +1 -1
index 437e80fdeb..62cc58d7e2 100644
@@ -1,4 +1,4 @@
 label stm32mp157a-dk1-buildroot
   kernel /boot/zImage
   devicetree /boot/stm32mp157a-dk1.dtb
-  append root=/dev/mmcblk0p4 rootwait
+  append root=/dev/mmcblk0p5 rootwait
board/stmicroelectronics/stm32mp157a-dk1/patches/uboot/0001-uboot-stm32mp1-uboot-env.patch new file +13 -0
new file mode 100644
index 0000000000..9582974caf
@@ -0,0 +1,13 @@
+diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+index 6787619290..85c0e1d0a3 100644
+--- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
++++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+@@ -16,7 +16,7 @@
+ 	config {
+ 		u-boot,boot-led = "heartbeat";
+ 		u-boot,error-led = "error";
+-		u-boot,mmc-env-partition = "ssbl";
++		u-boot,mmc-env-partition = "env";
+ 		st,adc_usb_pd = <&adc1 18>, <&adc1 19>;
+ 		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+ 		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf +1 -1
index 5b7f56ee77..e1b3ca9f61 100644
@@ -1,4 +1,4 @@
 label stm32mp157c-dk2-buildroot
   kernel /boot/zImage
   devicetree /boot/stm32mp157c-dk2.dtb
-  append root=/dev/mmcblk0p4 rootwait
+  append root=/dev/mmcblk0p5 rootwait
board/stmicroelectronics/stm32mp157c-dk2/patches/uboot/0001-uboot-stm32mp1-uboot-env.patch new file +13 -0
new file mode 100644
index 0000000000..9582974caf
@@ -0,0 +1,13 @@
+diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+index 6787619290..85c0e1d0a3 100644
+--- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
++++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+@@ -16,7 +16,7 @@
+ 	config {
+ 		u-boot,boot-led = "heartbeat";
+ 		u-boot,error-led = "error";
+-		u-boot,mmc-env-partition = "ssbl";
++		u-boot,mmc-env-partition = "env";
+ 		st,adc_usb_pd = <&adc1 18>, <&adc1 19>;
+ 		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+ 		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
configs/stm32mp157a_dk1_defconfig +5 -4
index 6883aaba7b..4f34456e9d 100644
@@ -1,11 +1,12 @@
 BR2_arm=y
 BR2_cortex_a7=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_8=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_10=y
 BR2_ROOTFS_OVERLAY="board/stmicroelectronics/stm32mp157a-dk1/overlay/"
+BR2_GLOBAL_PATCH_DIR="board/stmicroelectronics/stm32mp157a-dk1/patches/"
 BR2_ROOTFS_POST_IMAGE_SCRIPT="board/stmicroelectronics/common/stm32mp157/post-image.sh"
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.8.13"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.10.10"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
 BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/stmicroelectronics/stm32mp157a-dk1/linux.config"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
@@ -17,7 +18,7 @@ BR2_TARGET_ROOTFS_EXT2_SIZE="120M"
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
 BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.2"
+BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.4"
 BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="stm32mp1"
 BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="STM32MP_SDMMC=1 AARCH32_SP=sp_min DTB_FILE_NAME=stm32mp157a-dk1.dtb"
 BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="*.stm32"
@@ -25,7 +26,7 @@ BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_DTC=y
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2020.07"
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2020.10"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="stm32mp15_trusted"
 BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/stmicroelectronics/stm32mp157a-dk1/uboot-fragment.config"
 # BR2_TARGET_UBOOT_FORMAT_BIN is not set
configs/stm32mp157c_dk2_defconfig +5 -4
index 50d875749b..1f3028dcd1 100644
@@ -1,11 +1,12 @@
 BR2_arm=y
 BR2_cortex_a7=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_8=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_10=y
 BR2_ROOTFS_OVERLAY="board/stmicroelectronics/stm32mp157c-dk2/overlay/"
+BR2_GLOBAL_PATCH_DIR="board/stmicroelectronics/stm32mp157c-dk2/patches/"
 BR2_ROOTFS_POST_IMAGE_SCRIPT="board/stmicroelectronics/common/stm32mp157/post-image.sh"
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.8.13"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.10.10"
 BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
 BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/stmicroelectronics/stm32mp157c-dk2/linux.config"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
@@ -17,7 +18,7 @@ BR2_TARGET_ROOTFS_EXT2_SIZE="120M"
 # BR2_TARGET_ROOTFS_TAR is not set
 BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
 BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.2"
+BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.4"
 BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="stm32mp1"
 BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="STM32MP_SDMMC=1 AARCH32_SP=sp_min DTB_FILE_NAME=stm32mp157c-dk2.dtb"
 BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="*.stm32"
@@ -25,7 +26,7 @@ BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_DTC=y
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2020.07"
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2020.10"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="stm32mp15_trusted"
 BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/stmicroelectronics/stm32mp157c-dk2/uboot-fragment.config"
 # BR2_TARGET_UBOOT_FORMAT_BIN is not set
Signature · 1 line
2.30.0
#1 lore raw

RFC PATCH 1/1 stm32mp1: modify gpt partitions to fix BSP update

Quoted 29 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Sergey" == Sergey Matyukevich <[email protected]> writes:

Hi all,
BSP update for stm32mp1 boards does not work right out of the box. The first boot is ok, but the second boot fails:

NOTICE:  CPU: STM32MP157CAC Rev.B
NOTICE:  Model: STMicroelectronics STM32MP157C-DK2 Discovery Board
NOTICE:  Board: MB1272 Var2.0 Rev.C-01
NOTICE:  BL2: v2.4(release):2020.11-1087-g8fac193e6d-dirty
NOTICE:  BL2: Built : 20:58:09, Jan 27 2021
ERROR:   Checksum: 0x5023a37 (awaited: 0x5046ea4)
ERROR:   Header check failed
ERROR:   BL2: Failed to load image id 5 (-12)

The root cause is in changes for stm32mp1 trusted defconfig in updated
U-Boot: see U-Boot commit 76db1681da52 ("stm32mp1: use a specific SD/eMMC partition for U-Boot enviromnent"). Starting from that commit, U-Boot environment is stored at the end of the U-Boot partition. As a result, saving environment changes GPT partition checksum verified by ATF.

IIUC at least the following two approaches can be implemented to make updated BSP work smoothly.

The first approach is to modify U-Boot config fragment for stm32mp1 boards and to re-enable saving U-Boot environment on ext4. However this choice implies certain restriction on rootfs ext4 features since it should be writable by U-Boot. See the mentioned U-Boot commit message for details.

Quoted 4 lines

Another approach is implemented by the attached patch: keep U-Boot environment on a dedicated GPT partition.

Thoughts ? Comments ?

If upstream wants to use a separate partition for the environment, then that is fine by me - But I would prefer to not patch u-boot and just name the environment partition ssbl.

Signature · 1 line
Bye, Peter Korsgaard
#2 lore raw

RFC PATCH 1/1 stm32mp1: modify gpt partitions to fix BSP update

Hello,

Quoted 23 lines
Quoted 22 lines
NOTICE:  CPU: STM32MP157CAC Rev.B
NOTICE:  Model: STMicroelectronics STM32MP157C-DK2 Discovery Board
NOTICE:  Board: MB1272 Var2.0 Rev.C-01
NOTICE:  BL2: v2.4(release):2020.11-1087-g8fac193e6d-dirty
NOTICE:  BL2: Built : 20:58:09, Jan 27 2021
ERROR:   Checksum: 0x5023a37 (awaited: 0x5046ea4)
ERROR:   Header check failed
ERROR:   BL2: Failed to load image id 5 (-12)

The root cause is in changes for stm32mp1 trusted defconfig in updated
U-Boot: see U-Boot commit 76db1681da52 ("stm32mp1: use a specific SD/eMMC partition for U-Boot enviromnent"). Starting from that commit, U-Boot environment is stored at the end of the U-Boot partition. As a result, saving environment changes GPT partition checksum verified by ATF.

IIUC at least the following two approaches can be implemented to make updated BSP work smoothly.

The first approach is to modify U-Boot config fragment for stm32mp1 boards and to re-enable saving U-Boot environment on ext4. However this choice implies certain restriction on rootfs ext4 features since it should be writable by U-Boot. See the mentioned U-Boot commit message for details.

Quoted 8 lines
Quoted 4 lines

Another approach is implemented by the attached patch: keep U-Boot environment on a dedicated GPT partition.

Thoughts ? Comments ?

If upstream wants to use a separate partition for the environment, then that is fine by me - But I would prefer to not patch u-boot and just name the environment partition ssbl.

Sure, I would also prerfer not to patch u-boot. However on stm32mp1 platform, ATF attempts to load BL33 bootloader from 'ssbl' partition. So using this name for environment partition does not work.

Regards,
Sergey

#3 lore raw

RFC PATCH 1/1 stm32mp1: modify gpt partitions to fix BSP update

Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Sergey" == Sergey Matyukevich <[email protected]> writes:

Hi,

Quoted 7 lines
Quoted 3 lines

If upstream wants to use a separate partition for the environment, then that is fine by me - But I would prefer to not patch u-boot and just name the environment partition ssbl.

Sure, I would also prerfer not to patch u-boot. However on stm32mp1 platform, ATF attempts to load BL33 bootloader from 'ssbl' partition. So using this name for environment partition does not work.

So is upstream U-Boot broken? Why doesn't it get fixed? Sorry, I don't follow?

Signature · 1 line
Bye, Peter Korsgaard
#4 lore raw

RFC PATCH 1/1 stm32mp1: modify gpt partitions to fix BSP update

Quoted 10 lines
Quoted 7 lines
Quoted 3 lines

If upstream wants to use a separate partition for the environment, then that is fine by me - But I would prefer to not patch u-boot and just name the environment partition ssbl.

Sure, I would also prerfer not to patch u-boot. However on stm32mp1 platform, ATF attempts to load BL33 bootloader from 'ssbl' partition. So using this name for environment partition does not work.

So is upstream U-Boot broken? Why doesn't it get fixed? Sorry, I don't follow?

Unless I am missing something, it looks like 'trusted' u-boot defconfig has an issue. Let me re-iterate a brief summary. Previously stm32mp1 u-boot by default stored its environment as a file on ext4 filesystem. Recently default option has been changed. Now stm32mp1 u-boot keeps its environment at the end of its own SSBL partition. This is ok for 'basic' boot chain. However this is not the case for the 'trusted' boot chain since ATF verifies SSBL partition checksum.

P.S. I have not yet tried to communicate with u-boot upstream.

Regards,
Sergey

#5 lore raw

RFC PATCH 1/1 stm32mp1: modify gpt partitions to fix BSP update

In reply to Sergey Matyukevich

Hello Sergey,

Quoted 28 lines · Sergey Matyukevich

Hi all,

BSP update for stm32mp1 boards does not work right out of the box. The first boot is ok, but the second boot fails:

NOTICE:  CPU: STM32MP157CAC Rev.B
NOTICE:  Model: STMicroelectronics STM32MP157C-DK2 Discovery Board
NOTICE:  Board: MB1272 Var2.0 Rev.C-01
NOTICE:  BL2: v2.4(release):2020.11-1087-g8fac193e6d-dirty
NOTICE:  BL2: Built : 20:58:09, Jan 27 2021
ERROR:   Checksum: 0x5023a37 (awaited: 0x5046ea4)
ERROR:   Header check failed
ERROR:   BL2: Failed to load image id 5 (-12)

The root cause is in changes for stm32mp1 trusted defconfig in updated
U-Boot: see U-Boot commit 76db1681da52 ("stm32mp1: use a specific SD/eMMC partition for U-Boot enviromnent"). Starting from that commit, U-Boot environment is stored at the end of the U-Boot partition. As a result, saving environment changes GPT partition checksum verified by ATF.

IIUC at least the following two approaches can be implemented to make updated BSP work smoothly.

The first approach is to modify U-Boot config fragment for stm32mp1 boards and to re-enable saving U-Boot environment on ext4. However this choice implies certain restriction on rootfs ext4 features since it should be writable by U-Boot. See the mentioned U-Boot commit message for details.

Quoted 4 lines

Another approach is implemented by the attached patch: keep U-Boot environment on a dedicated GPT partition.

Thoughts ? Comments ?

I've experienced the same problems on stm32mp157c-dk2 board and I was going to send similar patches as you with the additional partition to keep env there. IMO changing the default board's config would require keeping synchronization between every U-Boot update what would not be so convenient. I was looking at the way how yocto solves this problem but I didn't find anything useful. Anyway - I've tested your series and there is a kernel crash related to the usb dwc2 driver:

[??? 1.534376] dwc2 49000000.usb-otg: supply vusb_d not found, using dummy regulator
[??? 1.540852] dwc2 49000000.usb-otg: supply vusb_a not found, using dummy regulator
[??? 1.551269] dwc2 49000000.usb-otg: Configuration mismatch. dr_mode forced to host
[??? 1.563905] ------------[ cut here ]------------
[??? 1.567113] WARNING: CPU: 1 PID: 42 at drivers/usb/dwc2/core.c:609 dwc2_drd_init+0x104/0x150
[??? 1.575530] Modules linked in:
[??? 1.578570] CPU: 1 PID: 42 Comm: kworker/1:2 Not tainted 5.10.10 #1 [??? 1.584834] Hardware name: STM32 (Device Tree Support)
[??? 1.589984] Workqueue: events deferred_probe_work_func
[??? 1.595129] [<c010d4b4>] (unwind_backtrace) from [<c0109f58>] (show_stack+0x10/0x14)
[??? 1.602871] [<c0109f58>] (show_stack) from [<c0703dec>] (dump_stack+0xc4/0xd8)
[??? 1.610093] [<c0703dec>] (dump_stack) from [<c0701670>] (__warn+0xc0/0xd8)
[??? 1.616961] [<c0701670>] (__warn) from [<c07016ec>] (warn_slowpath_fmt+0x64/0xc8)
[??? 1.624454] [<c07016ec>] (warn_slowpath_fmt) from [<c0500210>] (dwc2_drd_init+0x104/0x150)
[??? 1.632722] [<c0500210>] (dwc2_drd_init) from [<c04ffc5c>] (dwc2_driver_probe+0x44c/0x6d4)
[??? 1.640991] [<c04ffc5c>] (dwc2_driver_probe) from [<c045a274>] (platform_drv_probe+0x48/0x98)
[??? 1.649523] [<c045a274>] (platform_drv_probe) from [<c04582d0>] (really_probe+0x1dc/0x3b8)
[??? 1.657789] [<c04582d0>] (really_probe) from [<c0458618>] (driver_probe_device+0x5c/0xb4)
[??? 1.665969] [<c0458618>] (driver_probe_device) from [<c0456748>] (bus_for_each_drv+0x84/0xd0)
[??? 1.674501] [<c0456748>] (bus_for_each_drv) from [<c0458080>] (__device_attach+0xf0/0x15c)
[??? 1.682768] [<c0458080>] (__device_attach) from [<c0457424>] (bus_probe_device+0x84/0x8c)
[??? 1.690949] [<c0457424>] (bus_probe_device) from [<c04578b8>] (deferred_probe_work_func+0x64/0x90)
[??? 1.699917] [<c04578b8>] (deferred_probe_work_func) from [<c0131474>] (process_one_work+0x1c8/0x424)
[??? 1.709056] [<c0131474>] (process_one_work) from [<c0131918>] (worker_thread+0x248/0x520)
[??? 1.717235] [<c0131918>] (worker_thread) from [<c01370b8>] (kthread+0x130/0x170)
[??? 1.724628] [<c01370b8>] (kthread) from [<c0100148>] (ret_from_fork+0x14/0x2c)
[??? 1.731841] Exception stack(0xc162dfb0 to 0xc162dff8)
[??? 1.736884] dfa0:???????????????????????????????????? 00000000 00000000 00000000 00000000
[??? 1.745075] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[??? 1.753254] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [??? 1.759856] ---[ end trace cb00fc5721509727 ]---
[??? 1.765261] dwc2 49000000.usb-otg: DWC OTG Controller
[??? 1.769716] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 1
[??? 1.777060] dwc2 49000000.usb-otg: irq 52, io mem 0x49000000

so IMO we should wait for the next release that will fix that issues.

There are even more errors when init is being loaded:

[??? 2.431029] hub 2-1:1.0: USB hub found
[??? 2.431165] Freeing unused kernel memory: 1024K
[??? 2.438040] hub 2-1:1.0: 4 ports detected
[??? 2.442215] Run /sbin/init as init process
mount: you must be root
mount: you must be root
mkdir: can't create directory '/dev/pts': Permission denied
mkdir: can't create directory '/dev/shm': Permission denied
mount: you must be root
hostname: sethostname: Operation not permitted
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Saving random seed: SKIP (read-only file system detected)
mkdir: can't create directory '/run/network': Read-only file system Starting network: ip: RTNETLINK answers: Operation not permitted
ip: SIOCSIFFLAGS: Operation not permitted
ifup: can't open '/var/run/ifstate.new': Read-only file system FAIL
can't open /dev/console: Permission denied
can't open /dev/console: Permission denied
can't open /dev/console: Permission denied
can't open /dev/console: Permission denied
can't open /dev/console: Permission denied
can't open /dev/console: Permission denied

Anyway you can also bump U-Boot version to the 2021.01 as it's the latest one.

Best
Bartek

Quoted 162 lines

Regards,
Sergey

---
  .../common/stm32mp157/genimage.cfg.template         |  4 ++++
  .../overlay/boot/extlinux/extlinux.conf             |  2 +-
  .../uboot/0001-uboot-stm32mp1-uboot-env.patch       | 13 +++++++++++++
  .../overlay/boot/extlinux/extlinux.conf             |  2 +-
  .../uboot/0001-uboot-stm32mp1-uboot-env.patch       | 13 +++++++++++++
  configs/stm32mp157a_dk1_defconfig                   |  9 +++++----
  configs/stm32mp157c_dk2_defconfig                   |  9 +++++----
  7 files changed, 42 insertions(+), 10 deletions(-)

create mode 100644 board/stmicroelectronics/stm32mp157a-dk1/patches/uboot/0001-uboot-stm32mp1-uboot-env.patch create mode 100644 board/stmicroelectronics/stm32mp157c-dk2/patches/uboot/0001-uboot-stm32mp1-uboot-env.patch

board/stmicroelectronics/common/stm32mp157/genimage.cfg.template +4 -0
index f341c19f2f..12f79efa90 100644
@@ -15,6 +15,10 @@ image sdcard.img {
  		image = "u-boot.stm32"
  	}
 
+	partition env {
+		size = 16K
+	}
+
  	partition rootfs {
  		image = "rootfs.ext4"
  		bootable = "yes"
board/stmicroelectronics/stm32mp157a-dk1/overlay/boot/extlinux/extlinux.conf +1 -1
index 437e80fdeb..62cc58d7e2 100644
@@ -1,4 +1,4 @@
  label stm32mp157a-dk1-buildroot
    kernel /boot/zImage
    devicetree /boot/stm32mp157a-dk1.dtb
-  append root=/dev/mmcblk0p4 rootwait
+  append root=/dev/mmcblk0p5 rootwait
board/stmicroelectronics/stm32mp157a-dk1/patches/uboot/0001-uboot-stm32mp1-uboot-env.patch new file +13 -0
new file mode 100644
index 0000000000..9582974caf
@@ -0,0 +1,13 @@
+diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+index 6787619290..85c0e1d0a3 100644
+--- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
++++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+@@ -16,7 +16,7 @@
+ 	config {
+ 		u-boot,boot-led = "heartbeat";
+ 		u-boot,error-led = "error";
+-		u-boot,mmc-env-partition = "ssbl";
++		u-boot,mmc-env-partition = "env";
+ 		st,adc_usb_pd = <&adc1 18>, <&adc1 19>;
+ 		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+ 		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf +1 -1
index 5b7f56ee77..e1b3ca9f61 100644
@@ -1,4 +1,4 @@
  label stm32mp157c-dk2-buildroot
    kernel /boot/zImage
    devicetree /boot/stm32mp157c-dk2.dtb
-  append root=/dev/mmcblk0p4 rootwait
+  append root=/dev/mmcblk0p5 rootwait
board/stmicroelectronics/stm32mp157c-dk2/patches/uboot/0001-uboot-stm32mp1-uboot-env.patch new file +13 -0
new file mode 100644
index 0000000000..9582974caf
@@ -0,0 +1,13 @@
+diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+index 6787619290..85c0e1d0a3 100644
+--- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
++++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+@@ -16,7 +16,7 @@
+ 	config {
+ 		u-boot,boot-led = "heartbeat";
+ 		u-boot,error-led = "error";
+-		u-boot,mmc-env-partition = "ssbl";
++		u-boot,mmc-env-partition = "env";
+ 		st,adc_usb_pd = <&adc1 18>, <&adc1 19>;
+ 		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+ 		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
configs/stm32mp157a_dk1_defconfig +5 -4
index 6883aaba7b..4f34456e9d 100644
@@ -1,11 +1,12 @@
  BR2_arm=y
  BR2_cortex_a7=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_8=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_10=y
  BR2_ROOTFS_OVERLAY="board/stmicroelectronics/stm32mp157a-dk1/overlay/"
+BR2_GLOBAL_PATCH_DIR="board/stmicroelectronics/stm32mp157a-dk1/patches/"
  BR2_ROOTFS_POST_IMAGE_SCRIPT="board/stmicroelectronics/common/stm32mp157/post-image.sh"
  BR2_LINUX_KERNEL=y
  BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.8.13"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.10.10"
  BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
  BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/stmicroelectronics/stm32mp157a-dk1/linux.config"
  BR2_LINUX_KERNEL_DTS_SUPPORT=y
@@ -17,7 +18,7 @@ BR2_TARGET_ROOTFS_EXT2_SIZE="120M"
  # BR2_TARGET_ROOTFS_TAR is not set
  BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
  BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.2"
+BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.4"
  BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="stm32mp1"
  BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="STM32MP_SDMMC=1 AARCH32_SP=sp_min DTB_FILE_NAME=stm32mp157a-dk1.dtb"
  BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="*.stm32"
@@ -25,7 +26,7 @@ BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_DTC=y
  BR2_TARGET_UBOOT=y
  BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
  BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2020.07"
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2020.10"
  BR2_TARGET_UBOOT_BOARD_DEFCONFIG="stm32mp15_trusted"
  BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/stmicroelectronics/stm32mp157a-dk1/uboot-fragment.config"
  # BR2_TARGET_UBOOT_FORMAT_BIN is not set
configs/stm32mp157c_dk2_defconfig +5 -4
index 50d875749b..1f3028dcd1 100644
@@ -1,11 +1,12 @@
  BR2_arm=y
  BR2_cortex_a7=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_8=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_10=y
  BR2_ROOTFS_OVERLAY="board/stmicroelectronics/stm32mp157c-dk2/overlay/"
+BR2_GLOBAL_PATCH_DIR="board/stmicroelectronics/stm32mp157c-dk2/patches/"
  BR2_ROOTFS_POST_IMAGE_SCRIPT="board/stmicroelectronics/common/stm32mp157/post-image.sh"
  BR2_LINUX_KERNEL=y
  BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.8.13"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.10.10"
  BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
  BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/stmicroelectronics/stm32mp157c-dk2/linux.config"
  BR2_LINUX_KERNEL_DTS_SUPPORT=y
@@ -17,7 +18,7 @@ BR2_TARGET_ROOTFS_EXT2_SIZE="120M"
  # BR2_TARGET_ROOTFS_TAR is not set
  BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
  BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.2"
+BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.4"
  BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="stm32mp1"
  BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="STM32MP_SDMMC=1 AARCH32_SP=sp_min DTB_FILE_NAME=stm32mp157c-dk2.dtb"
  BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="*.stm32"
@@ -25,7 +26,7 @@ BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_DTC=y
  BR2_TARGET_UBOOT=y
  BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
  BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2020.07"
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2020.10"
  BR2_TARGET_UBOOT_BOARD_DEFCONFIG="stm32mp15_trusted"
  BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/stmicroelectronics/stm32mp157c-dk2/uboot-fragment.config"
  # BR2_TARGET_UBOOT_FORMAT_BIN is not set