Add support of Lontium lt8912 MIPI to HDMI bridge
Subsystems (4)
v2 cover Add support of Lontium lt8912 MIPI to HDMI bridge
Hello,
this patch set adds the support of the Lontium lt8912 MIPI to HDMI bridge in the kernel.
It's only support the video part, not the audio part yet since I don't have the datasheet of this component. I get the current i2c configuration from Digi and Boundary drivers.
Developed using the DB_DSIHD board from BoundaryDevices.
Update in v2
- Use standard data-lanes instead of a custom prop;
- Use hdmi-connector node.
Thanks,
Adrien Grassein
Adrien Grassein (2):
dt-bindings: display: bridge: Add documentation for LT8912 drm/bridge: Introduce LT8912 DSI to HDMI bridge
.../display/bridge/lontium,lt8912.yaml | 102 +++ MAINTAINERS | 6 + drivers/gpu/drm/bridge/Kconfig | 14 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/lontium-lt8912.c | 719 ++++++++++++++++++ 5 files changed, 842 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml create mode 100644 drivers/gpu/drm/bridge/lontium-lt8912.c
Signature · 1 line
2.25.1
PATCH v2 1/2 dt-bindings: display: bridge: Add documentation for LT8912
Lontium LT8912 is a DSI to HDMI bridge.
--- .../display/bridge/lontium,lt8912.yaml | 102 ++++++++++++++++++ MAINTAINERS | 5 + 2 files changed, 107 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml
Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml new file +102 -0
@@ -0,0 +1,102 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/lontium,lt8912.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Lontium LT8912 MIPI to HDMI Bridge + +maintainers: + - Adrien Grassein <[email protected]> + +description: | + The LT8912 is a bridge device which convert DSI to HDMI + +properties: + compatible: + enum: + - lontium,lt8912 + + reg: + maxItems: 1 + + reset-gpios: + maxItems: 1 + description: GPIO connected to active high RESET pin. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: + Primary MIPI port for MIPI input + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: true + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: | + HDMI port, should be connected to a node compatible with the + hdmi-connector binding. + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - reset-gpios + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c4 { + #address-cells = <1>; + #size-cells = <0>; + + hdmi-bridge@48 { + compatible = "lontium,lt8912"; + reg = <0x48>; + reset-gpios = <&max7323 0 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi_out_in: endpoint { + data-lanes = <0 1 2 3>; + remote-endpoint = <&mipi_dsi_out>; + }; + }; + + port@1 { + reg = <1>; + + endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; + }; + }; + +...
MAINTAINERS +5 -0
@@ -10440,6 +10440,11 @@ S: Maintained T: git git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid.git F: drivers/hid/hid-lg-g15.c +LONTIUM LT8912 MIPI TO HDMI BRIDGE +M: Adrien Grassein <[email protected]> +S: Maintained +F: Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml + LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) M: Sathya Prakash <[email protected]> M: Sreekanth Reddy <[email protected]>
Signature · 1 line
2.25.1
Rob Herring
maintainerRe: [PATCH v2 1/2] dt-bindings: display: bridge: Add documentation for LT8912
Quoted 9 lines · Adrien Grassein
Lontium LT8912 is a DSI to HDMI bridge.
Signed-off-by Adrien Grassein <[email protected]>--- .../display/bridge/lontium,lt8912.yaml | 102 ++++++++++++++++++ MAINTAINERS | 5 + 2 files changed, 107 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml
My bot found errors running 'make dt_binding_check' on your patch:
yamllint warnings/errors:
dtschema/dtc warnings/errors:
make[1]: *** Deleting file 'Documentation/devicetree/bindings/display/bridge/lontium,lt8912.example.dt.yaml'
Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.8/dist-packages/dtschema/schemas/media/video-interfaces.yaml' make[1]: *** [scripts/Makefile.lib:344: Documentation/devicetree/bindings/display/bridge/lontium,lt8912.example.dt.yaml] Error 255
make: *** [Makefile:1370: dt_binding_check] Error 2
See https://patchwork.ozlabs.org/patch/1440379
This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date:
pip3 install dtschema --upgrade
Please check and re-submit.
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 1/2] dt-bindings: display: bridge: Add documentation for LT8912
In reply to Adrien GrasseinQuoted 8 lines · Adrien Grassein
Lontium LT8912 is a DSI to HDMI bridge.
Signed-off-by Adrien Grassein <[email protected]>--- .../display/bridge/lontium,lt8912.yaml | 102 ++++++++++++++++++ MAINTAINERS | 5 + 2 files changed, 107 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml
Other than needing to wait for 5.12-rc1 to be merged into drm-misc,
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v2 2/2 drm/bridge: Introduce LT8912 DSI to HDMI bridge
In reply to Adrien GrasseinLontium Lt8912 is a DSI to HDMI bridge.
--- MAINTAINERS | 1 + drivers/gpu/drm/bridge/Kconfig | 14 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/lontium-lt8912.c | 719 ++++++++++++++++++++++++ 4 files changed, 735 insertions(+) create mode 100644 drivers/gpu/drm/bridge/lontium-lt8912.c
MAINTAINERS +1 -0
@@ -10444,6 +10444,7 @@ LONTIUM LT8912 MIPI TO HDMI BRIDGE M: Adrien Grassein <[email protected]> S: Maintained F: Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml +F: drivers/gpu/drm/bridge/lontium-lt8912.c LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) M: Sathya Prakash <[email protected]>
drivers/gpu/drm/bridge/Kconfig +14 -0
@@ -48,6 +48,20 @@ config DRM_DISPLAY_CONNECTOR on ARM-based platforms. Saying Y here when this driver is not needed will not cause any issue. +config DRM_LONTIUM_LT8912 + tristate "Lontium LT8912 DSI/HDMI bridge" + depends on OF + select DRM_PANEL_BRIDGE + select DRM_KMS_HELPER + select REGMAP_I2C + help + Driver for Lontium LT8912 DSI to HDMI bridge + chip driver. + Please say Y if you have such hardware. + + Say M here if you want to support this hardware as a module. + The module will be named "lontium-lt8912". + config DRM_LONTIUM_LT9611 tristate "Lontium LT9611 DSI/HDMI bridge" select SND_SOC_HDMI_CODEC if SND_SOC
drivers/gpu/drm/bridge/Makefile +1 -0
@@ -2,6 +2,7 @@ obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o +obj-$(CONFIG_DRM_LONTIUM_LT8912) += lontium-lt8912.o obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o obj-$(CONFIG_DRM_LONTIUM_LT9611UXC) += lontium-lt9611uxc.o obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o
drivers/gpu/drm/bridge/lontium-lt8912.c new file +719 -0
719 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH v2 2/2] drm/bridge: Introduce LT8912 DSI to HDMI bridge
Hey Adrien,
Thanks for submitting this!
Quoted 110 lines · Adrien Grassein
Lontium Lt8912 is a DSI to HDMI bridge.
Signed-off-by Adrien Grassein <[email protected]>--- MAINTAINERS | 1 + drivers/gpu/drm/bridge/Kconfig | 14 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/lontium-lt8912.c | 719 ++++++++++++++++++++++++ 4 files changed, 735 insertions(+) create mode 100644 drivers/gpu/drm/bridge/lontium-lt8912.cMAINTAINERS +1
-0@@ -10444,6 +10444,7 @@ LONTIUM LT8912 MIPI TO HDMI BRIDGE M: Adrien Grassein <[email protected]> S: Maintained F: Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml +F: drivers/gpu/drm/bridge/lontium-lt8912.c LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) M: Sathya Prakash <[email protected]>drivers/gpu/drm/bridge/Kconfig +14
-0@@ -48,6 +48,20 @@ config DRM_DISPLAY_CONNECTOR on ARM-based platforms. Saying Y here when this driver is not needed will not cause any issue. +config DRM_LONTIUM_LT8912 + tristate "Lontium LT8912 DSI/HDMI bridge" + depends on OF + select DRM_PANEL_BRIDGE + select DRM_KMS_HELPER + select REGMAP_I2C + help + Driver for Lontium LT8912 DSI to HDMI bridge + chip driver. + Please say Y if you have such hardware. + + Say M here if you want to support this hardware as a module. + The module will be named "lontium-lt8912". + config DRM_LONTIUM_LT9611 tristate "Lontium LT9611 DSI/HDMI bridge" select SND_SOC_HDMI_CODEC if SND_SOCdrivers/gpu/drm/bridge/Makefile +1
-0@@ -2,6 +2,7 @@ obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o +obj-$(CONFIG_DRM_LONTIUM_LT8912) += lontium-lt8912.o obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o obj-$(CONFIG_DRM_LONTIUM_LT9611UXC) += lontium-lt9611uxc.o obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.odrivers/gpu/drm/bridge/lontium-lt8912.c new file +43
-0@@ -0,0 +1,719 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Copyright (c) 2018, The Linux Foundation. All rights reserved. +*/ + +#include <linux/device.h> +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/gpio.h> +#include <linux/of_gpio.h> +#include <linux/regmap.h> + +#include <drm/drm_probe_helper.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_of.h> + +#include <video/videomode.h> + +#define I2C_MAIN 0 +#define I2C_ADDR_MAIN 0x48 + +#define I2C_CEC_DSI 1 +#define I2C_ADDR_CEC_DSI 0x49 + +#define I2C_MAX_IDX 2 + +#define HPD_WORK_DELAY_MS 1000 + +struct lt8912 { +struct device *dev; +struct drm_bridge bridge; +struct drm_connector connector; + +struct i2c_client *i2c_client[I2C_MAX_IDX ]; +struct regmap *regmap[I2C_MAX_IDX ]; + +struct device_node *host_node; +struct drm_bridge *hdmi_port; + +struct mipi_dsi_device *dsi; + +struct gpio_desc *gp_reset;
drivers/gpu/drm/bridge/lontium-lt8912.c line 53
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ +struct videomode mode; + +u8 data_lanes; +bool is_power_on; +bool is_attached; +}; + +static int lt8912_write_init_config (struct lt8912 *lt) +{
For the following register accesses it would be nice to see the registers named and the value written to them documented. If you don't have access to all of that information, not adding it is acceptable, but it will make the driver harder to maintain & extend going forward.
So if possible, document registers in the same way it was done for lt9611 [1].
[1] https://github.com/torvalds/linux/blob/master/drivers/gpu/drm/bridge/lontium-lt9611.c#L444
Quoted 163 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +163
-0+const struct reg_sequence seq[] = { +/* Digital clock en*/ + {0x08 ,0xff }, + {0x09 ,0xff }, + {0x0a ,0xff }, + {0x0b ,0x7c }, + {0x0c ,0xff }, + {0x42 ,0x04 }, + +/*Tx Analog*/ + {0x31 ,0xb1 }, + {0x32 ,0xb1 }, + {0x33 ,0x0e }, + {0x37 ,0x00 }, + {0x38 ,0x22 }, + {0x60 ,0x82 }, + +/*Cbus Analog*/ + {0x39 ,0x45 }, + {0x3a ,0x00 }, + {0x3b ,0x00 }, + +/*HDMI Pll Analog*/ + {0x44 ,0x31 }, + {0x55 ,0x44 }, + {0x57 ,0x01 }, + {0x5a ,0x02 }, + +/*MIPI Analog*/ + {0x3e ,0xd6 }, + {0x3f ,0xd4 }, + {0x41 ,0x3c }, + {0xB2 ,0x00 }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_MAIN ], seq,ARRAY_SIZE (seq)); +} + +static int lt8912_write_mipi_basic_config (struct lt8912 *lt) +{ +const struct reg_sequence seq[] = { + {0x12 ,0x04 }, + {0x14 ,0x00 }, + {0x15 ,0x00 }, + {0x1a ,0x03 }, + {0x1b ,0x03 }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_CEC_DSI ], seq,ARRAY_SIZE (seq)); +}; + +static int lt8912_write_dds_config (struct lt8912 *lt) +{ +const struct reg_sequence seq[] = { + {0x4e ,0xff }, + {0x4f ,0x56 }, + {0x50 ,0x69 }, + {0x51 ,0x80 }, + {0x1f ,0x5e }, + {0x20 ,0x01 }, + {0x21 ,0x2c }, + {0x22 ,0x01 }, + {0x23 ,0xfa }, + {0x24 ,0x00 }, + {0x25 ,0xc8 }, + {0x26 ,0x00 }, + {0x27 ,0x5e }, + {0x28 ,0x01 }, + {0x29 ,0x2c }, + {0x2a ,0x01 }, + {0x2b ,0xfa }, + {0x2c ,0x00 }, + {0x2d ,0xc8 }, + {0x2e ,0x00 }, + {0x42 ,0x64 }, + {0x43 ,0x00 }, + {0x44 ,0x04 }, + {0x45 ,0x00 }, + {0x46 ,0x59 }, + {0x47 ,0x00 }, + {0x48 ,0xf2 }, + {0x49 ,0x06 }, + {0x4a ,0x00 }, + {0x4b ,0x72 }, + {0x4c ,0x45 }, + {0x4d ,0x00 }, + {0x52 ,0x08 }, + {0x53 ,0x00 }, + {0x54 ,0xb2 }, + {0x55 ,0x00 }, + {0x56 ,0xe4 }, + {0x57 ,0x0d }, + {0x58 ,0x00 }, + {0x59 ,0xe4 }, + {0x5a ,0x8a }, + {0x5b ,0x00 }, + {0x5c ,0x34 }, + {0x1e ,0x4f }, + {0x51 ,0x00 }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_CEC_DSI ], seq,ARRAY_SIZE (seq)); +} + +static int lt8912_write_rxlogicres_config (struct lt8912 *lt) +{ +int ret; + + ret =regmap_write (lt->regmap[I2C_MAIN ],0x03 ,0x7f ); +usleep_range (10000 ,20000 ); + ret |=regmap_write (lt->regmap[I2C_MAIN ],0x03 ,0xff ); + +return ret; +}; + +static int lt8912_write_lvds_config (struct lt8912 *lt) +{ +const struct reg_sequence seq[] = { + {0x44 ,0x30 }, + {0x51 ,0x05 }, + {0x50 ,0x24 }, + {0x51 ,0x2d }, + {0x52 ,0x04 }, + {0x69 ,0x0e }, + {0x69 ,0x8e }, + {0x6a ,0x00 }, + {0x6c ,0xb8 }, + {0x6b ,0x51 }, + {0x04 ,0xfb }, + {0x04 ,0xff }, + {0x7f ,0x00 }, + {0xa8 ,0x13 }, + {0x02 ,0xf7 }, + {0x02 ,0xff }, + {0x03 ,0xcf }, + {0x03 ,0xff }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_CEC_DSI ], seq,ARRAY_SIZE (seq)); +}; + +static inline struct lt8912 *bridge_to_lt8912 (struct drm_bridge *b) +{ + return container_of(b, struct lt8912, bridge); +} + +static inline struct lt8912 *connector_to_lt8912 (struct drm_connector *c) +{ + return container_of(c, struct lt8912, connector); +} + +static const struct regmap_config lt8912_regmap_config = { + .reg_bits =8 , + .val_bits =8 , + .max_register =0xff , +}; + +static int lt8912_init_i2c (struct lt8912 *lt) +{ +unsigned int i; +int ret; +struct i2c_board_info info[] = { + {I2C_BOARD_INFO ("lt8912p0" ,I2C_ADDR_MAIN ), },
drivers/gpu/drm/bridge/lontium-lt8912.c line 226
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ { I2C_BOARD_INFO("lt8912p1", I2C_ADDR_CEC_DSI), }, + }; + +if (!lt) +return -ENODEV ; + +for (i =0 ; i <ARRAY_SIZE (info); i++) { +if (i >0 ) { + lt->i2c_client[i] =i2c_new_dummy_device (lt->i2c_client[0 ]->adapter, + info[i].addr);
Bad indentation. Some of these bad indentations look ok for tab-width=4, however tab-width=8 is what the style guide dictates.
drivers/gpu/drm/bridge/lontium-lt8912.c line 231
Quoted 5 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +5
-0+if (!lt->i2c_client[i]) +return -ENODEV ; + } + lt->regmap[i] =devm_regmap_init_i2c (lt->i2c_client[i], + <8912_regmap_config);
Bad indentation.
Quoted 161 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +161
-0+if (IS_ERR (lt->regmap[i])) { + ret =PTR_ERR (lt->regmap[i]); +return ret; + } + } +return 0 ; +} + +static int lt8912_free_i2c (struct lt8912 *lt) +{ +unsigned int i; + +for (i =1 ; i <I2C_MAX_IDX ; i++) +i2c_unregister_device (lt->i2c_client[i]); + +return 0 ; +} + +static int lt8912_hard_power_on (struct lt8912 *lt) +{ +gpiod_set_value_cansleep (lt->gp_reset,0 ); +msleep (20 ); + +return 0 ; +} + +static void lt8912_hard_power_off (struct lt8912 *lt) +{ +gpiod_set_value_cansleep (lt->gp_reset,1 ); +msleep (20 ); + lt->is_power_on = false; +} + +static int lt8912_video_setup (struct lt8912 *lt) +{ +u32 hactive, h_total, hpw, hfp, hbp; +u32 vactive, v_total, vpw, vfp, vbp; +u8 settle =0x08 ; +int ret; + +if (!lt) +return -EINVAL ; + + hactive = lt->mode.hactive; + hfp = lt->mode.hfront_porch; + hpw = lt->mode.hsync_len; + hbp = lt->mode.hback_porch; + h_total = hactive + hfp + hpw + hbp; + + vactive = lt->mode.vactive; + vfp = lt->mode.vfront_porch; + vpw = lt->mode.vsync_len; + vbp = lt->mode.vback_porch; + v_total = vactive + vfp + vpw + vbp; + +if (vactive <=600 ) + settle =0x04 ; +else if (vactive ==1080 ) + settle =0x0a ; + + ret =regmap_write (lt->regmap[I2C_CEC_DSI ],0x10 ,0x01 ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x11 , settle); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x18 , hpw); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x19 , vpw); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x1c , hactive &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x1d , hactive >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x2f ,0x0c ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x34 , h_total &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x35 , h_total >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x36 , v_total &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x37 , v_total >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x38 , vbp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x39 , vbp >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3a , vfp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3b , vfp >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3c , hbp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3d , hbp >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3e , hfp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3f , hfp >>8 ); + +return ret; +} + +static int lt8912_soft_power_on (struct lt8912 *lt) +{ +if (!lt->is_power_on) { +u32 lanes = lt->data_lanes; + +lt8912_write_init_config (lt); +regmap_write (lt->regmap[I2C_CEC_DSI ],0x13 , lanes &3 ); + +lt8912_write_mipi_basic_config (lt); + + lt->is_power_on = true; + } + +return 0 ; +} + +static int lt8912_video_on (struct lt8912 *lt) +{ +int ret; + + ret =lt8912_video_setup (lt); +if (ret <0 ) + goto end; + + ret =lt8912_write_dds_config (lt); +if (ret <0 ) + goto end; + + ret =lt8912_write_rxlogicres_config (lt); +if (ret <0 ) + goto end; + + ret =lt8912_write_lvds_config (lt); +if (ret <0 ) + goto end; + +end: +return ret; +} + +static enum drm_connector_status +lt8912_connector_detect (struct drm_connector *connector,bool force) +{ +struct lt8912 *lt =connector_to_lt8912 (connector); + +return drm_bridge_detect (lt->hdmi_port); +} + +static const struct drm_connector_funcs lt8912_connector_funcs = { + .detect = lt8912_connector_detect, + .fill_modes = drm_helper_probe_single_connector_modes, + .destroy = drm_connector_cleanup, + .reset = drm_atomic_helper_connector_reset, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +static enum drm_mode_status +lt8912_connector_mode_valid (struct drm_connector *connector, +struct drm_display_mode *mode) +{ +if (mode->clock >150000 ) +return MODE_CLOCK_HIGH ; + +if (mode->hdisplay >1920 ) +return MODE_BAD_HVALUE ; + +if (mode->vdisplay >1080 ) +return MODE_BAD_VVALUE ; + +return MODE_OK ;
drivers/gpu/drm/bridge/lontium-lt8912.c line 402
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+} + +static int lt8912_connector_get_modes (struct drm_connector *connector) +{ +struct edid *edid; +int ret, num =0 ; +struct lt8912 *lt =connector_to_lt8912 (connector); +u32 bus_format =MEDIA_BUS_FMT_RGB888_1X24 ; + + edid =drm_bridge_get_edid (lt->hdmi_port, connector);
Memory leak, edid is never free'd.
drivers/gpu/drm/bridge/lontium-lt8912.c line 410
Quoted 8 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +8
-0+if (edid) { +drm_connector_update_edid_property (connector, edid); + num =drm_add_edid_modes (connector, edid); + }else +return ret; + + ret =drm_display_info_set_bus_formats (&connector->display_info, + &bus_format,1 );
Bad indentation.
Quoted 50 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +50
-0+if (ret) +return ret; + +return num; +} + +static const struct drm_connector_helper_funcs lt8912_connector_helper_funcs = { + .get_modes = lt8912_connector_get_modes, + .mode_valid = lt8912_connector_mode_valid, +}; + +static void lt8912_bridge_mode_set (struct drm_bridge *bridge, +const struct drm_display_mode *mode, +const struct drm_display_mode *adj) +{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); + +drm_display_mode_to_videomode (adj, <->mode); +} + +static void lt8912_bridge_enable (struct drm_bridge *bridge) +{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); + +lt8912_video_on (lt); +} + +static int lt8912_attach_dsi (struct lt8912 *lt) +{ +struct device *dev = lt->dev; +struct mipi_dsi_host *host; +struct mipi_dsi_device *dsi; +int ret =-1 ; +const struct mipi_dsi_device_info info = { .type ="lt8912" , + .channel =0 , + .node =NULL , + }; + + host =of_find_mipi_dsi_host_by_node (lt->host_node); +if (!host) { +dev_err (dev,"failed to find dsi host\n" ); +return -EPROBE_DEFER ; + } + + dsi =mipi_dsi_device_register_full (host, &info); +if (IS_ERR (dsi)) { + ret =PTR_ERR (dsi); +dev_err (dev,"failed to create dsi device (%d)\n" , ret); + goto err_dsi_device; + }
drivers/gpu/drm/bridge/lontium-lt8912.c line 470
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ + lt->dsi = dsi; + + dsi->lanes = lt->data_lanes; + dsi->format =MIPI_DSI_FMT_RGB888 ; + + dsi->mode_flags =MIPI_DSI_MODE_VIDEO | +MIPI_DSI_MODE_VIDEO_BURST | +MIPI_DSI_MODE_LPM | +MIPI_DSI_MODE_EOT_PACKET ;
Maybe align the 3 last lines with where the 1st one starts.
Quoted 23 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +23
-0+ + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +dev_err (dev,"failed to attach dsi to host\n" ); + goto err_dsi_attach; + } + +return 0 ; + +err_dsi_attach: +mipi_dsi_device_unregister (dsi); +err_dsi_device: +return ret; +} + +static void lt8912_detach_dsi (struct lt8912 *lt) +{ +mipi_dsi_detach (lt->dsi); +mipi_dsi_device_unregister (lt->dsi); +} + +static int lt8912_bridge_init (struct drm_bridge *bridge) +{
drivers/gpu/drm/bridge/lontium-lt8912.c line 503
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+int ret; +struct lt8912 *lt =bridge_to_lt8912 (bridge); +struct drm_connector *connector = <->connector; + + +if (lt->hdmi_port->ops &DRM_BRIDGE_OP_DETECT ) { + connector->polled =DRM_CONNECTOR_POLL_HPD ; + }else { + connector->polled =DRM_CONNECTOR_POLL_CONNECT | +DRM_CONNECTOR_POLL_DISCONNECT ;
Bad indentation.
Quoted 17 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +17
-0+ } + + + ret =drm_connector_init (bridge->dev, connector, + <8912_connector_funcs, + lt->hdmi_port->type); +if (ret) + goto exit; + +drm_connector_helper_add (connector, <8912_connector_helper_funcs); + + connector->dpms =DRM_MODE_DPMS_OFF ; +drm_connector_attach_encoder (connector, bridge->encoder); + + + ret =lt8912_hard_power_on (lt); +if (ret)
drivers/gpu/drm/bridge/lontium-lt8912.c line 530
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ goto exit; + + ret =lt8912_soft_power_on (lt); + +exit: +return ret; +} + +static int lt8912_bridge_attach (struct drm_bridge *bridge, +enum drm_bridge_attach_flags flags)
Bad indentation.
drivers/gpu/drm/bridge/lontium-lt8912.c line 539
Quoted 9 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +9
-0+{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); +int ret; + +/* No need to check the return of this function */ +drm_bridge_attach (lt->bridge.encoder, + lt->hdmi_port, + <->bridge, + flags);
Bad indentation.
Quoted 23 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +23
-0+ +if (!(flags &DRM_BRIDGE_ATTACH_NO_CONNECTOR )) { + ret =lt8912_bridge_init (bridge); +if (ret) { +dev_err (lt->dev,"Failed to init bridge ! (%d)\n" , ret); +return ret; + } + } + + ret =lt8912_attach_dsi (lt); +if (ret) +return ret; + + lt->is_attached = true; + +return ret; +} + +static void lt8912_bridge_detach (struct drm_bridge *bridge) +{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); + +if (lt->is_attached) {
drivers/gpu/drm/bridge/lontium-lt8912.c line 572
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+lt8912_detach_dsi (lt); +lt8912_hard_power_off (lt); + } +} + +static const struct drm_bridge_funcs lt8912_bridge_funcs = { + .attach = lt8912_bridge_attach, + .detach = lt8912_bridge_detach, + .mode_set = lt8912_bridge_mode_set, + .enable = lt8912_bridge_enable,
Have a look at the documentation around in drm_bridge_funcs[1], some additional functions have to be implemented. I think you can look at lt9611[2] & lt9611uxc[3] for inspiration.
[1] https://dri.freedesktop.org/docs/drm/gpu/drm-kms-helpers.html#bridge-operations
[2] https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/bridge/lontium-lt9611.c#L947
[3] https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/bridge/lontium-lt9611uxc.c#L542
Quoted 75 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +75
-0+}; + +static int lt8912_parse_dt (struct lt8912 *lt) +{ +struct gpio_desc *gp_reset; +struct device *dev = lt->dev; +int ret =0 ; +struct device_node *port_node; +struct device_node *endpoint; + + gp_reset =devm_gpiod_get_optional (dev,"reset" ,GPIOD_OUT_HIGH ); +if (IS_ERR (gp_reset)) { + ret =PTR_ERR (gp_reset); +if (ret != -EPROBE_DEFER ) +dev_err (dev,"Failed to get reset gpio: %d\n" , ret); +return ret; + } + lt->gp_reset = gp_reset; + + + endpoint =of_graph_get_endpoint_by_regs (dev->of_node,0 ,-1 ); +if (IS_ERR (endpoint)) { + ret =PTR_ERR (endpoint); + goto end; + } + + lt->data_lanes =of_property_count_u32_elems (endpoint,"data-lanes" ); +of_node_put (endpoint); + + lt->host_node =of_graph_get_remote_node (dev->of_node,0 ,-1 ); +if (!lt->host_node) { +dev_err (lt->dev,"%s: Failed to get remote port\n" , __func__); + ret = -ENODEV ; + goto end; + } + + port_node =of_graph_get_remote_node (dev->of_node,1 ,-1 ); +if (!port_node) { +dev_err (lt->dev,"%s: Failed to get connector port\n" , __func__); + ret = -ENODEV ; + goto err_free_host_node; + } + + lt->hdmi_port =of_drm_find_bridge (port_node); +if (IS_ERR (lt->hdmi_port)) { +dev_err (lt->dev,"%s: Failed to get hdmi port\n" , __func__); + ret =PTR_ERR (lt->hdmi_port); +of_node_put (lt->host_node); + goto end; + } + +if (!of_device_is_compatible (port_node,"hdmi-connector" )) { +dev_err (lt->dev,"%s: Failed to get hdmi port\n" , __func__); + ret = -EINVAL ; + } + +of_node_put (port_node); + +end: +return ret; + +err_free_host_node: +of_node_put (lt->host_node); +return ret; +} + +static int lt8912_put_dt (struct lt8912 *lt) +{ +of_node_put (lt->host_node); +return 0 ; +} + +static int lt8912_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{
drivers/gpu/drm/bridge/lontium-lt8912.c line 657
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+static struct lt8912 *lt; +int ret =0 ; +struct device *dev = &client->dev; + + lt =devm_kzalloc (dev,sizeof (struct lt8912 ),GFP_KERNEL ); +if (!lt) +return -ENOMEM ; + + lt->dev = dev; + lt->i2c_client[0 ] = client;
The i2c_client that is created from the DT address and passed into lt8912_probe will be overwritten by the i2c clients created in lt8912_init_i2c before it is ever used.
A related issue is that this device has two I2C addresses, which doesn't fit super neatly into the I2C driver model[1]. Since both addresses can't be provided by the DT, method one doesn't fit this driver. Method 2 doesn't fit well either, since the I2C bus isn't internal to the device. And 3&4 are not applicable. I'd say the two options are #1 splitting this driver, #2 keeping it like it is. I'm leaning towards #2 since both addresses correspond to a physical chip.
[1] https://www.kernel.org/doc/html/latest/i2c/instantiating-devices.html
Quoted 42 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +42
-0+ + ret =lt8912_parse_dt (lt); +if (ret) + goto err_dt_parse; + + ret =lt8912_init_i2c (lt); +if (ret) + goto err_i2c; + +i2c_set_clientdata (client, lt); + + lt->bridge.funcs = <8912_bridge_funcs; + lt->bridge.of_node = dev->of_node; +drm_bridge_add (<->bridge); + +return 0 ; + +err_i2c: +lt8912_put_dt (lt); +err_dt_parse: +return ret; +} + +static int lt8912_remove (struct i2c_client *client) +{ +struct lt8912 *lt =i2c_get_clientdata (client); + +lt8912_bridge_detach (<->bridge); +drm_bridge_remove (<->bridge); +lt8912_free_i2c (lt); +lt8912_put_dt (lt); + +return 0 ; +} + +static const struct of_device_id lt8912_dt_match[] = { + {.compatible ="lontium,lt8912" }, + {} +}; +MODULE_DEVICE_TABLE (of, lt8912_dt_match); + +static const struct i2c_device_id lt8912_id[] = {
drivers/gpu/drm/bridge/lontium-lt8912.c line 709
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ {"lt8912", 0}, + {}, +}; +MODULE_DEVICE_TABLE(i2c, lt8912_id); + +static struct i2c_driver lt8912_i2c_driver = { + .driver = { + .name = "lt8912", + .of_match_table = lt8912_dt_match, + .owner = THIS_MODULE,
The .owner assignment is redundant as it is later re-assigned in[1].
module_i2c_driver -> i2c_add_driver -> i2c_register_driver
[1] https://elixir.bootlin.com/linux/latest/source/drivers/i2c/i2c-core-base.c#L1796
Quoted 11 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-1+ }, + .probe = lt8912_probe, + .remove = lt8912_remove, + .id_table = lt8912_id, +}; +module_i2c_driver (lt8912_i2c_driver); + +MODULE_AUTHOR ("Adrien Grassein <[email protected]>" ); +MODULE_DESCRIPTION ("lt8912 drm driver" ); +MODULE_LICENSE ("GPL v2" ); --
Quoted 2 lines
2.25.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 2/2] drm/bridge: Introduce LT8912 DSI to HDMI bridge
Hey Robert,
Thank you for your time and for your review.
Quoted 132 lines · Robert Foss
Hey Adrien,
Thanks for submitting this!
Quoted 110 lines · Adrien Grassein
Lontium Lt8912 is a DSI to HDMI bridge.
Signed-off-by Adrien Grassein <[email protected]>--- MAINTAINERS | 1 + drivers/gpu/drm/bridge/Kconfig | 14 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/lontium-lt8912.c | 719 ++++++++++++++++++++++++ 4 files changed, 735 insertions(+) create mode 100644 drivers/gpu/drm/bridge/lontium-lt8912.cMAINTAINERS +1
-0@@ -10444,6 +10444,7 @@ LONTIUM LT8912 MIPI TO HDMI BRIDGE M: Adrien Grassein <[email protected]> S: Maintained F: Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml +F: drivers/gpu/drm/bridge/lontium-lt8912.c LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) M: Sathya Prakash <[email protected]>drivers/gpu/drm/bridge/Kconfig +14
-0@@ -48,6 +48,20 @@ config DRM_DISPLAY_CONNECTOR on ARM-based platforms. Saying Y here when this driver is not needed will not cause any issue. +config DRM_LONTIUM_LT8912 + tristate "Lontium LT8912 DSI/HDMI bridge" + depends on OF + select DRM_PANEL_BRIDGE + select DRM_KMS_HELPER + select REGMAP_I2C + help + Driver for Lontium LT8912 DSI to HDMI bridge + chip driver. + Please say Y if you have such hardware. + + Say M here if you want to support this hardware as a module. + The module will be named "lontium-lt8912". + config DRM_LONTIUM_LT9611 tristate "Lontium LT9611 DSI/HDMI bridge" select SND_SOC_HDMI_CODEC if SND_SOCdrivers/gpu/drm/bridge/Makefile +1
-0@@ -2,6 +2,7 @@ obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o +obj-$(CONFIG_DRM_LONTIUM_LT8912) += lontium-lt8912.o obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o obj-$(CONFIG_DRM_LONTIUM_LT9611UXC) += lontium-lt9611uxc.o obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.odrivers/gpu/drm/bridge/lontium-lt8912.c new file +43
-0@@ -0,0 +1,719 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Copyright (c) 2018, The Linux Foundation. All rights reserved. +*/ + +#include <linux/device.h> +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/gpio.h> +#include <linux/of_gpio.h> +#include <linux/regmap.h> + +#include <drm/drm_probe_helper.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_of.h> + +#include <video/videomode.h> + +#define I2C_MAIN 0 +#define I2C_ADDR_MAIN 0x48 + +#define I2C_CEC_DSI 1 +#define I2C_ADDR_CEC_DSI 0x49 + +#define I2C_MAX_IDX 2 + +#define HPD_WORK_DELAY_MS 1000 + +struct lt8912 { +struct device *dev; +struct drm_bridge bridge; +struct drm_connector connector; + +struct i2c_client *i2c_client[I2C_MAX_IDX ]; +struct regmap *regmap[I2C_MAX_IDX ]; + +struct device_node *host_node; +struct drm_bridge *hdmi_port; + +struct mipi_dsi_device *dsi; + +struct gpio_desc *gp_reset;drivers/gpu/drm/bridge/lontium-lt8912.c line 53
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ +struct videomode mode; + +u8 data_lanes; +bool is_power_on; +bool is_attached; +}; + +static int lt8912_write_init_config (struct lt8912 *lt) +{For the following register accesses it would be nice to see the registers named and the value written to them documented. If you don't have access to all of that information, not adding it is acceptable, but it will make the driver harder to maintain & extend going forward.
Quoted 4 lines
So if possible, document registers in the same way it was done for lt9611 [1].
[1] https://github.com/torvalds/linux/blob/master/drivers/gpu/drm/bridge/lontium-lt9611.c#L444
Sorry, I don't have any documentation about this chip. I can't document these registers.
Quoted 635 lines
Quoted 163 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +163
-0+const struct reg_sequence seq[] = { +/* Digital clock en*/ + {0x08 ,0xff }, + {0x09 ,0xff }, + {0x0a ,0xff }, + {0x0b ,0x7c }, + {0x0c ,0xff }, + {0x42 ,0x04 }, + +/*Tx Analog*/ + {0x31 ,0xb1 }, + {0x32 ,0xb1 }, + {0x33 ,0x0e }, + {0x37 ,0x00 }, + {0x38 ,0x22 }, + {0x60 ,0x82 }, + +/*Cbus Analog*/ + {0x39 ,0x45 }, + {0x3a ,0x00 }, + {0x3b ,0x00 }, + +/*HDMI Pll Analog*/ + {0x44 ,0x31 }, + {0x55 ,0x44 }, + {0x57 ,0x01 }, + {0x5a ,0x02 }, + +/*MIPI Analog*/ + {0x3e ,0xd6 }, + {0x3f ,0xd4 }, + {0x41 ,0x3c }, + {0xB2 ,0x00 }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_MAIN ], seq,ARRAY_SIZE (seq)); +} + +static int lt8912_write_mipi_basic_config (struct lt8912 *lt) +{ +const struct reg_sequence seq[] = { + {0x12 ,0x04 }, + {0x14 ,0x00 }, + {0x15 ,0x00 }, + {0x1a ,0x03 }, + {0x1b ,0x03 }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_CEC_DSI ], seq,ARRAY_SIZE (seq)); +}; + +static int lt8912_write_dds_config (struct lt8912 *lt) +{ +const struct reg_sequence seq[] = { + {0x4e ,0xff }, + {0x4f ,0x56 }, + {0x50 ,0x69 }, + {0x51 ,0x80 }, + {0x1f ,0x5e }, + {0x20 ,0x01 }, + {0x21 ,0x2c }, + {0x22 ,0x01 }, + {0x23 ,0xfa }, + {0x24 ,0x00 }, + {0x25 ,0xc8 }, + {0x26 ,0x00 }, + {0x27 ,0x5e }, + {0x28 ,0x01 }, + {0x29 ,0x2c }, + {0x2a ,0x01 }, + {0x2b ,0xfa }, + {0x2c ,0x00 }, + {0x2d ,0xc8 }, + {0x2e ,0x00 }, + {0x42 ,0x64 }, + {0x43 ,0x00 }, + {0x44 ,0x04 }, + {0x45 ,0x00 }, + {0x46 ,0x59 }, + {0x47 ,0x00 }, + {0x48 ,0xf2 }, + {0x49 ,0x06 }, + {0x4a ,0x00 }, + {0x4b ,0x72 }, + {0x4c ,0x45 }, + {0x4d ,0x00 }, + {0x52 ,0x08 }, + {0x53 ,0x00 }, + {0x54 ,0xb2 }, + {0x55 ,0x00 }, + {0x56 ,0xe4 }, + {0x57 ,0x0d }, + {0x58 ,0x00 }, + {0x59 ,0xe4 }, + {0x5a ,0x8a }, + {0x5b ,0x00 }, + {0x5c ,0x34 }, + {0x1e ,0x4f }, + {0x51 ,0x00 }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_CEC_DSI ], seq,ARRAY_SIZE (seq)); +} + +static int lt8912_write_rxlogicres_config (struct lt8912 *lt) +{ +int ret; + + ret =regmap_write (lt->regmap[I2C_MAIN ],0x03 ,0x7f ); +usleep_range (10000 ,20000 ); + ret |=regmap_write (lt->regmap[I2C_MAIN ],0x03 ,0xff ); + +return ret; +}; + +static int lt8912_write_lvds_config (struct lt8912 *lt) +{ +const struct reg_sequence seq[] = { + {0x44 ,0x30 }, + {0x51 ,0x05 }, + {0x50 ,0x24 }, + {0x51 ,0x2d }, + {0x52 ,0x04 }, + {0x69 ,0x0e }, + {0x69 ,0x8e }, + {0x6a ,0x00 }, + {0x6c ,0xb8 }, + {0x6b ,0x51 }, + {0x04 ,0xfb }, + {0x04 ,0xff }, + {0x7f ,0x00 }, + {0xa8 ,0x13 }, + {0x02 ,0xf7 }, + {0x02 ,0xff }, + {0x03 ,0xcf }, + {0x03 ,0xff }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_CEC_DSI ], seq,ARRAY_SIZE (seq)); +}; + +static inline struct lt8912 *bridge_to_lt8912 (struct drm_bridge *b) +{ + return container_of(b, struct lt8912, bridge); +} + +static inline struct lt8912 *connector_to_lt8912 (struct drm_connector *c) +{ + return container_of(c, struct lt8912, connector); +} + +static const struct regmap_config lt8912_regmap_config = { + .reg_bits =8 , + .val_bits =8 , + .max_register =0xff , +}; + +static int lt8912_init_i2c (struct lt8912 *lt) +{ +unsigned int i; +int ret; +struct i2c_board_info info[] = { + {I2C_BOARD_INFO ("lt8912p0" ,I2C_ADDR_MAIN ), },drivers/gpu/drm/bridge/lontium-lt8912.c line 226
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ { I2C_BOARD_INFO("lt8912p1", I2C_ADDR_CEC_DSI), }, + }; + +if (!lt) +return -ENODEV ; + +for (i =0 ; i <ARRAY_SIZE (info); i++) { +if (i >0 ) { + lt->i2c_client[i] =i2c_new_dummy_device (lt->i2c_client[0 ]->adapter, + info[i].addr);Bad indentation. Some of these bad indentations look ok for tab-width=4, however tab-width=8 is what the style guide dictates.
drivers/gpu/drm/bridge/lontium-lt8912.c line 231
Quoted 5 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +5
-0+if (!lt->i2c_client[i]) +return -ENODEV ; + } + lt->regmap[i] =devm_regmap_init_i2c (lt->i2c_client[i], + <8912_regmap_config);Bad indentation.
Quoted 161 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +161
-0+if (IS_ERR (lt->regmap[i])) { + ret =PTR_ERR (lt->regmap[i]); +return ret; + } + } +return 0 ; +} + +static int lt8912_free_i2c (struct lt8912 *lt) +{ +unsigned int i; + +for (i =1 ; i <I2C_MAX_IDX ; i++) +i2c_unregister_device (lt->i2c_client[i]); + +return 0 ; +} + +static int lt8912_hard_power_on (struct lt8912 *lt) +{ +gpiod_set_value_cansleep (lt->gp_reset,0 ); +msleep (20 ); + +return 0 ; +} + +static void lt8912_hard_power_off (struct lt8912 *lt) +{ +gpiod_set_value_cansleep (lt->gp_reset,1 ); +msleep (20 ); + lt->is_power_on = false; +} + +static int lt8912_video_setup (struct lt8912 *lt) +{ +u32 hactive, h_total, hpw, hfp, hbp; +u32 vactive, v_total, vpw, vfp, vbp; +u8 settle =0x08 ; +int ret; + +if (!lt) +return -EINVAL ; + + hactive = lt->mode.hactive; + hfp = lt->mode.hfront_porch; + hpw = lt->mode.hsync_len; + hbp = lt->mode.hback_porch; + h_total = hactive + hfp + hpw + hbp; + + vactive = lt->mode.vactive; + vfp = lt->mode.vfront_porch; + vpw = lt->mode.vsync_len; + vbp = lt->mode.vback_porch; + v_total = vactive + vfp + vpw + vbp; + +if (vactive <=600 ) + settle =0x04 ; +else if (vactive ==1080 ) + settle =0x0a ; + + ret =regmap_write (lt->regmap[I2C_CEC_DSI ],0x10 ,0x01 ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x11 , settle); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x18 , hpw); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x19 , vpw); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x1c , hactive &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x1d , hactive >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x2f ,0x0c ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x34 , h_total &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x35 , h_total >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x36 , v_total &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x37 , v_total >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x38 , vbp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x39 , vbp >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3a , vfp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3b , vfp >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3c , hbp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3d , hbp >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3e , hfp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3f , hfp >>8 ); + +return ret; +} + +static int lt8912_soft_power_on (struct lt8912 *lt) +{ +if (!lt->is_power_on) { +u32 lanes = lt->data_lanes; + +lt8912_write_init_config (lt); +regmap_write (lt->regmap[I2C_CEC_DSI ],0x13 , lanes &3 ); + +lt8912_write_mipi_basic_config (lt); + + lt->is_power_on = true; + } + +return 0 ; +} + +static int lt8912_video_on (struct lt8912 *lt) +{ +int ret; + + ret =lt8912_video_setup (lt); +if (ret <0 ) + goto end; + + ret =lt8912_write_dds_config (lt); +if (ret <0 ) + goto end; + + ret =lt8912_write_rxlogicres_config (lt); +if (ret <0 ) + goto end; + + ret =lt8912_write_lvds_config (lt); +if (ret <0 ) + goto end; + +end: +return ret; +} + +static enum drm_connector_status +lt8912_connector_detect (struct drm_connector *connector,bool force) +{ +struct lt8912 *lt =connector_to_lt8912 (connector); + +return drm_bridge_detect (lt->hdmi_port); +} + +static const struct drm_connector_funcs lt8912_connector_funcs = { + .detect = lt8912_connector_detect, + .fill_modes = drm_helper_probe_single_connector_modes, + .destroy = drm_connector_cleanup, + .reset = drm_atomic_helper_connector_reset, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +static enum drm_mode_status +lt8912_connector_mode_valid (struct drm_connector *connector, +struct drm_display_mode *mode) +{ +if (mode->clock >150000 ) +return MODE_CLOCK_HIGH ; + +if (mode->hdisplay >1920 ) +return MODE_BAD_HVALUE ; + +if (mode->vdisplay >1080 ) +return MODE_BAD_VVALUE ; + +return MODE_OK ;drivers/gpu/drm/bridge/lontium-lt8912.c line 402
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+} + +static int lt8912_connector_get_modes (struct drm_connector *connector) +{ +struct edid *edid; +int ret, num =0 ; +struct lt8912 *lt =connector_to_lt8912 (connector); +u32 bus_format =MEDIA_BUS_FMT_RGB888_1X24 ; + + edid =drm_bridge_get_edid (lt->hdmi_port, connector);Memory leak, edid is never free'd.
drivers/gpu/drm/bridge/lontium-lt8912.c line 410
Quoted 8 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +8
-0+if (edid) { +drm_connector_update_edid_property (connector, edid); + num =drm_add_edid_modes (connector, edid); + }else +return ret; + + ret =drm_display_info_set_bus_formats (&connector->display_info, + &bus_format,1 );Bad indentation.
Quoted 50 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +50
-0+if (ret) +return ret; + +return num; +} + +static const struct drm_connector_helper_funcs lt8912_connector_helper_funcs = { + .get_modes = lt8912_connector_get_modes, + .mode_valid = lt8912_connector_mode_valid, +}; + +static void lt8912_bridge_mode_set (struct drm_bridge *bridge, +const struct drm_display_mode *mode, +const struct drm_display_mode *adj) +{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); + +drm_display_mode_to_videomode (adj, <->mode); +} + +static void lt8912_bridge_enable (struct drm_bridge *bridge) +{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); + +lt8912_video_on (lt); +} + +static int lt8912_attach_dsi (struct lt8912 *lt) +{ +struct device *dev = lt->dev; +struct mipi_dsi_host *host; +struct mipi_dsi_device *dsi; +int ret =-1 ; +const struct mipi_dsi_device_info info = { .type ="lt8912" , + .channel =0 , + .node =NULL , + }; + + host =of_find_mipi_dsi_host_by_node (lt->host_node); +if (!host) { +dev_err (dev,"failed to find dsi host\n" ); +return -EPROBE_DEFER ; + } + + dsi =mipi_dsi_device_register_full (host, &info); +if (IS_ERR (dsi)) { + ret =PTR_ERR (dsi); +dev_err (dev,"failed to create dsi device (%d)\n" , ret); + goto err_dsi_device; + }drivers/gpu/drm/bridge/lontium-lt8912.c line 470
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ + lt->dsi = dsi; + + dsi->lanes = lt->data_lanes; + dsi->format =MIPI_DSI_FMT_RGB888 ; + + dsi->mode_flags =MIPI_DSI_MODE_VIDEO | +MIPI_DSI_MODE_VIDEO_BURST | +MIPI_DSI_MODE_LPM | +MIPI_DSI_MODE_EOT_PACKET ;Maybe align the 3 last lines with where the 1st one starts.
Quoted 23 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +23
-0+ + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +dev_err (dev,"failed to attach dsi to host\n" ); + goto err_dsi_attach; + } + +return 0 ; + +err_dsi_attach: +mipi_dsi_device_unregister (dsi); +err_dsi_device: +return ret; +} + +static void lt8912_detach_dsi (struct lt8912 *lt) +{ +mipi_dsi_detach (lt->dsi); +mipi_dsi_device_unregister (lt->dsi); +} + +static int lt8912_bridge_init (struct drm_bridge *bridge) +{drivers/gpu/drm/bridge/lontium-lt8912.c line 503
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+int ret; +struct lt8912 *lt =bridge_to_lt8912 (bridge); +struct drm_connector *connector = <->connector; + + +if (lt->hdmi_port->ops &DRM_BRIDGE_OP_DETECT ) { + connector->polled =DRM_CONNECTOR_POLL_HPD ; + }else { + connector->polled =DRM_CONNECTOR_POLL_CONNECT | +DRM_CONNECTOR_POLL_DISCONNECT ;Bad indentation.
Quoted 17 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +17
-0+ } + + + ret =drm_connector_init (bridge->dev, connector, + <8912_connector_funcs, + lt->hdmi_port->type); +if (ret) + goto exit; + +drm_connector_helper_add (connector, <8912_connector_helper_funcs); + + connector->dpms =DRM_MODE_DPMS_OFF ; +drm_connector_attach_encoder (connector, bridge->encoder); + + + ret =lt8912_hard_power_on (lt); +if (ret)drivers/gpu/drm/bridge/lontium-lt8912.c line 530
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ goto exit; + + ret =lt8912_soft_power_on (lt); + +exit: +return ret; +} + +static int lt8912_bridge_attach (struct drm_bridge *bridge, +enum drm_bridge_attach_flags flags)Bad indentation.
drivers/gpu/drm/bridge/lontium-lt8912.c line 539
Quoted 9 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +9
-0+{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); +int ret; + +/* No need to check the return of this function */ +drm_bridge_attach (lt->bridge.encoder, + lt->hdmi_port, + <->bridge, + flags);Bad indentation.
Quoted 23 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +23
-0+ +if (!(flags &DRM_BRIDGE_ATTACH_NO_CONNECTOR )) { + ret =lt8912_bridge_init (bridge); +if (ret) { +dev_err (lt->dev,"Failed to init bridge ! (%d)\n" , ret); +return ret; + } + } + + ret =lt8912_attach_dsi (lt); +if (ret) +return ret; + + lt->is_attached = true; + +return ret; +} + +static void lt8912_bridge_detach (struct drm_bridge *bridge) +{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); + +if (lt->is_attached) {drivers/gpu/drm/bridge/lontium-lt8912.c line 572
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+lt8912_detach_dsi (lt); +lt8912_hard_power_off (lt); + } +} + +static const struct drm_bridge_funcs lt8912_bridge_funcs = { + .attach = lt8912_bridge_attach, + .detach = lt8912_bridge_detach, + .mode_set = lt8912_bridge_mode_set, + .enable = lt8912_bridge_enable,Have a look at the documentation around in drm_bridge_funcs[1], some additional functions have to be implemented. I think you can look at lt9611[2] & lt9611uxc[3] for inspiration.
[1] https://dri.freedesktop.org/docs/drm/gpu/drm-kms-helpers.html#bridge-operations
[2] https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/bridge/lontium-lt9611.c#L947
[3] https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/bridge/lontium-lt9611uxc.c#L542Quoted 81 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +81
-0+}; + +static int lt8912_parse_dt (struct lt8912 *lt) +{ +struct gpio_desc *gp_reset; +struct device *dev = lt->dev; +int ret =0 ; +struct device_node *port_node; +struct device_node *endpoint; + + gp_reset =devm_gpiod_get_optional (dev,"reset" ,GPIOD_OUT_HIGH ); +if (IS_ERR (gp_reset)) { + ret =PTR_ERR (gp_reset); +if (ret != -EPROBE_DEFER ) +dev_err (dev,"Failed to get reset gpio: %d\n" , ret); +return ret; + } + lt->gp_reset = gp_reset; + + + endpoint =of_graph_get_endpoint_by_regs (dev->of_node,0 ,-1 ); +if (IS_ERR (endpoint)) { + ret =PTR_ERR (endpoint); + goto end; + } + + lt->data_lanes =of_property_count_u32_elems (endpoint,"data-lanes" ); +of_node_put (endpoint); + + lt->host_node =of_graph_get_remote_node (dev->of_node,0 ,-1 ); +if (!lt->host_node) { +dev_err (lt->dev,"%s: Failed to get remote port\n" , __func__); + ret = -ENODEV ; + goto end; + } + + port_node =of_graph_get_remote_node (dev->of_node,1 ,-1 ); +if (!port_node) { +dev_err (lt->dev,"%s: Failed to get connector port\n" , __func__); + ret = -ENODEV ; + goto err_free_host_node; + } + + lt->hdmi_port =of_drm_find_bridge (port_node); +if (IS_ERR (lt->hdmi_port)) { +dev_err (lt->dev,"%s: Failed to get hdmi port\n" , __func__); + ret =PTR_ERR (lt->hdmi_port); +of_node_put (lt->host_node); + goto end; + } + +if (!of_device_is_compatible (port_node,"hdmi-connector" )) { +dev_err (lt->dev,"%s: Failed to get hdmi port\n" , __func__); + ret = -EINVAL ; + } + +of_node_put (port_node); + +end: +return ret; + +err_free_host_node: +of_node_put (lt->host_node); +return ret; +} + +static int lt8912_put_dt (struct lt8912 *lt) +{ +of_node_put (lt->host_node); +return 0 ; +} + +static int lt8912_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +static struct lt8912 *lt; +int ret =0 ; +struct device *dev = &client->dev; + + lt =devm_kzalloc (dev,sizeof (struct lt8912 ),GFP_KERNEL ); +if (!lt)
Quoted 8 lines
drivers/gpu/drm/bridge/lontium-lt8912.c line 657
Quoted 4 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +4
-0+return -ENOMEM ; + + lt->dev = dev; + lt->i2c_client[0 ] = client;The
i2c_clientthat is created from the DT address and passed intolt8912_probewill be overwritten by the i2c clients created inlt8912_init_i2cbefore it is ever used.
I think you made a mistake here.
The lt8912_init_i2c function only initializes the lt->i2c_client[1]. (You can check the if condition).
Quoted 70 lines
A related issue is that this device has two I2C addresses, which doesn't fit super neatly into the I2C driver model[1]. Since both addresses can't be provided by the DT, method one doesn't fit this driver. Method 2 doesn't fit well either, since the I2C bus isn't internal to the device. And 3&4 are not applicable. I'd say the two options are #1 splitting this driver, #2 keeping it like it is. I'm leaning towards #2 since both addresses correspond to a physical chip.
[1] https://www.kernel.org/doc/html/latest/i2c/instantiating-devices.html
Quoted 42 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +42
-0+ + ret =lt8912_parse_dt (lt); +if (ret) + goto err_dt_parse; + + ret =lt8912_init_i2c (lt); +if (ret) + goto err_i2c; + +i2c_set_clientdata (client, lt); + + lt->bridge.funcs = <8912_bridge_funcs; + lt->bridge.of_node = dev->of_node; +drm_bridge_add (<->bridge); + +return 0 ; + +err_i2c: +lt8912_put_dt (lt); +err_dt_parse: +return ret; +} + +static int lt8912_remove (struct i2c_client *client) +{ +struct lt8912 *lt =i2c_get_clientdata (client); + +lt8912_bridge_detach (<->bridge); +drm_bridge_remove (<->bridge); +lt8912_free_i2c (lt); +lt8912_put_dt (lt); + +return 0 ; +} + +static const struct of_device_id lt8912_dt_match[] = { + {.compatible ="lontium,lt8912" }, + {} +}; +MODULE_DEVICE_TABLE (of, lt8912_dt_match); + +static const struct i2c_device_id lt8912_id[] = {drivers/gpu/drm/bridge/lontium-lt8912.c line 709
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ {"lt8912", 0}, + {}, +}; +MODULE_DEVICE_TABLE(i2c, lt8912_id); + +static struct i2c_driver lt8912_i2c_driver = { + .driver = { + .name = "lt8912", + .of_match_table = lt8912_dt_match, + .owner = THIS_MODULE,The .owner assignment is redundant as it is later re-assigned in[1].
module_i2c_driver->i2c_add_driver->i2c_register_driver[1] https://elixir.bootlin.com/linux/latest/source/drivers/i2c/i2c-core-base.c#L1796
Quoted 13 lines
Quoted 11 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-1+ }, + .probe = lt8912_probe, + .remove = lt8912_remove, + .id_table = lt8912_id, +}; +module_i2c_driver (lt8912_i2c_driver); + +MODULE_AUTHOR ("Adrien Grassein <[email protected]>" ); +MODULE_DESCRIPTION ("lt8912 drm driver" ); +MODULE_LICENSE ("GPL v2" ); --Quoted 2 lines
2.25.1
I will send a new version with the fixes.
Thanks again,
Adrien Grassein
Re: [PATCH v2 2/2] drm/bridge: Introduce LT8912 DSI to HDMI bridge
Quoted 138 lines · Adrien Grassein
Hey Robert,
Thank you for your time and for your review.
Quoted 132 lines · Robert Foss
Hey Adrien,
Thanks for submitting this!
Quoted 110 lines · Adrien Grassein
Lontium Lt8912 is a DSI to HDMI bridge.
Signed-off-by Adrien Grassein <[email protected]>--- MAINTAINERS | 1 + drivers/gpu/drm/bridge/Kconfig | 14 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/lontium-lt8912.c | 719 ++++++++++++++++++++++++ 4 files changed, 735 insertions(+) create mode 100644 drivers/gpu/drm/bridge/lontium-lt8912.cMAINTAINERS +1
-0@@ -10444,6 +10444,7 @@ LONTIUM LT8912 MIPI TO HDMI BRIDGE M: Adrien Grassein <[email protected]> S: Maintained F: Documentation/devicetree/bindings/display/bridge/lontium,lt8912.yaml +F: drivers/gpu/drm/bridge/lontium-lt8912.c LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) M: Sathya Prakash <[email protected]>drivers/gpu/drm/bridge/Kconfig +14
-0@@ -48,6 +48,20 @@ config DRM_DISPLAY_CONNECTOR on ARM-based platforms. Saying Y here when this driver is not needed will not cause any issue. +config DRM_LONTIUM_LT8912 + tristate "Lontium LT8912 DSI/HDMI bridge" + depends on OF + select DRM_PANEL_BRIDGE + select DRM_KMS_HELPER + select REGMAP_I2C + help + Driver for Lontium LT8912 DSI to HDMI bridge + chip driver. + Please say Y if you have such hardware. + + Say M here if you want to support this hardware as a module. + The module will be named "lontium-lt8912". + config DRM_LONTIUM_LT9611 tristate "Lontium LT9611 DSI/HDMI bridge" select SND_SOC_HDMI_CODEC if SND_SOCdrivers/gpu/drm/bridge/Makefile +1
-0@@ -2,6 +2,7 @@ obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o +obj-$(CONFIG_DRM_LONTIUM_LT8912) += lontium-lt8912.o obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o obj-$(CONFIG_DRM_LONTIUM_LT9611UXC) += lontium-lt9611uxc.o obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.odrivers/gpu/drm/bridge/lontium-lt8912.c new file +43
-0@@ -0,0 +1,719 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Copyright (c) 2018, The Linux Foundation. All rights reserved. +*/ + +#include <linux/device.h> +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/gpio.h> +#include <linux/of_gpio.h> +#include <linux/regmap.h> + +#include <drm/drm_probe_helper.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_of.h> + +#include <video/videomode.h> + +#define I2C_MAIN 0 +#define I2C_ADDR_MAIN 0x48 + +#define I2C_CEC_DSI 1 +#define I2C_ADDR_CEC_DSI 0x49 + +#define I2C_MAX_IDX 2 + +#define HPD_WORK_DELAY_MS 1000 + +struct lt8912 { +struct device *dev; +struct drm_bridge bridge; +struct drm_connector connector; + +struct i2c_client *i2c_client[I2C_MAX_IDX ]; +struct regmap *regmap[I2C_MAX_IDX ]; + +struct device_node *host_node; +struct drm_bridge *hdmi_port; + +struct mipi_dsi_device *dsi; + +struct gpio_desc *gp_reset;drivers/gpu/drm/bridge/lontium-lt8912.c line 53
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ +struct videomode mode; + +u8 data_lanes; +bool is_power_on; +bool is_attached; +}; + +static int lt8912_write_init_config (struct lt8912 *lt) +{For the following register accesses it would be nice to see the registers named and the value written to them documented. If you don't have access to all of that information, not adding it is acceptable, but it will make the driver harder to maintain & extend going forward.
Quoted 7 lines
Quoted 4 lines
So if possible, document registers in the same way it was done for lt9611 [1].
[1] https://github.com/torvalds/linux/blob/master/drivers/gpu/drm/bridge/lontium-lt9611.c#L444
Sorry, I don't have any documentation about this chip. I can't document these registers.
Ack, let's work with what we've got then :)
Quoted 645 lines
Quoted 636 lines
Quoted 164 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +163
-0+const struct reg_sequence seq[] = { +/* Digital clock en*/ + {0x08 ,0xff }, + {0x09 ,0xff }, + {0x0a ,0xff }, + {0x0b ,0x7c }, + {0x0c ,0xff }, + {0x42 ,0x04 }, + +/*Tx Analog*/ + {0x31 ,0xb1 }, + {0x32 ,0xb1 }, + {0x33 ,0x0e }, + {0x37 ,0x00 }, + {0x38 ,0x22 }, + {0x60 ,0x82 }, + +/*Cbus Analog*/ + {0x39 ,0x45 }, + {0x3a ,0x00 }, + {0x3b ,0x00 }, + +/*HDMI Pll Analog*/ + {0x44 ,0x31 }, + {0x55 ,0x44 }, + {0x57 ,0x01 }, + {0x5a ,0x02 }, + +/*MIPI Analog*/ + {0x3e ,0xd6 }, + {0x3f ,0xd4 }, + {0x41 ,0x3c }, + {0xB2 ,0x00 }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_MAIN ], seq,ARRAY_SIZE (seq)); +} + +static int lt8912_write_mipi_basic_config (struct lt8912 *lt) +{ +const struct reg_sequence seq[] = { + {0x12 ,0x04 }, + {0x14 ,0x00 }, + {0x15 ,0x00 }, + {0x1a ,0x03 }, + {0x1b ,0x03 }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_CEC_DSI ], seq,ARRAY_SIZE (seq)); +}; + +static int lt8912_write_dds_config (struct lt8912 *lt) +{ +const struct reg_sequence seq[] = { + {0x4e ,0xff }, + {0x4f ,0x56 }, + {0x50 ,0x69 }, + {0x51 ,0x80 }, + {0x1f ,0x5e }, + {0x20 ,0x01 }, + {0x21 ,0x2c }, + {0x22 ,0x01 }, + {0x23 ,0xfa }, + {0x24 ,0x00 }, + {0x25 ,0xc8 }, + {0x26 ,0x00 }, + {0x27 ,0x5e }, + {0x28 ,0x01 }, + {0x29 ,0x2c }, + {0x2a ,0x01 }, + {0x2b ,0xfa }, + {0x2c ,0x00 }, + {0x2d ,0xc8 }, + {0x2e ,0x00 }, + {0x42 ,0x64 }, + {0x43 ,0x00 }, + {0x44 ,0x04 }, + {0x45 ,0x00 }, + {0x46 ,0x59 }, + {0x47 ,0x00 }, + {0x48 ,0xf2 }, + {0x49 ,0x06 }, + {0x4a ,0x00 }, + {0x4b ,0x72 }, + {0x4c ,0x45 }, + {0x4d ,0x00 }, + {0x52 ,0x08 }, + {0x53 ,0x00 }, + {0x54 ,0xb2 }, + {0x55 ,0x00 }, + {0x56 ,0xe4 }, + {0x57 ,0x0d }, + {0x58 ,0x00 }, + {0x59 ,0xe4 }, + {0x5a ,0x8a }, + {0x5b ,0x00 }, + {0x5c ,0x34 }, + {0x1e ,0x4f }, + {0x51 ,0x00 }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_CEC_DSI ], seq,ARRAY_SIZE (seq)); +} + +static int lt8912_write_rxlogicres_config (struct lt8912 *lt) +{ +int ret; + + ret =regmap_write (lt->regmap[I2C_MAIN ],0x03 ,0x7f ); +usleep_range (10000 ,20000 ); + ret |=regmap_write (lt->regmap[I2C_MAIN ],0x03 ,0xff ); + +return ret; +}; + +static int lt8912_write_lvds_config (struct lt8912 *lt) +{ +const struct reg_sequence seq[] = { + {0x44 ,0x30 }, + {0x51 ,0x05 }, + {0x50 ,0x24 }, + {0x51 ,0x2d }, + {0x52 ,0x04 }, + {0x69 ,0x0e }, + {0x69 ,0x8e }, + {0x6a ,0x00 }, + {0x6c ,0xb8 }, + {0x6b ,0x51 }, + {0x04 ,0xfb }, + {0x04 ,0xff }, + {0x7f ,0x00 }, + {0xa8 ,0x13 }, + {0x02 ,0xf7 }, + {0x02 ,0xff }, + {0x03 ,0xcf }, + {0x03 ,0xff }, + }; + +return regmap_multi_reg_write (lt->regmap[I2C_CEC_DSI ], seq,ARRAY_SIZE (seq)); +}; + +static inline struct lt8912 *bridge_to_lt8912 (struct drm_bridge *b) +{ + return container_of(b, struct lt8912, bridge); +} + +static inline struct lt8912 *connector_to_lt8912 (struct drm_connector *c) +{ + return container_of(c, struct lt8912, connector); +} + +static const struct regmap_config lt8912_regmap_config = { + .reg_bits =8 , + .val_bits =8 , + .max_register =0xff , +}; + +static int lt8912_init_i2c (struct lt8912 *lt) +{ +unsigned int i; +int ret; +struct i2c_board_info info[] = { + {I2C_BOARD_INFO ("lt8912p0" ,I2C_ADDR_MAIN ), },drivers/gpu/drm/bridge/lontium-lt8912.c line 226
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ { I2C_BOARD_INFO("lt8912p1", I2C_ADDR_CEC_DSI), }, + }; + +if (!lt) +return -ENODEV ; + +for (i =0 ; i <ARRAY_SIZE (info); i++) { +if (i >0 ) { + lt->i2c_client[i] =i2c_new_dummy_device (lt->i2c_client[0 ]->adapter, + info[i].addr);Bad indentation. Some of these bad indentations look ok for tab-width=4, however tab-width=8 is what the style guide dictates.
drivers/gpu/drm/bridge/lontium-lt8912.c line 231
Quoted 5 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +5
-0+if (!lt->i2c_client[i]) +return -ENODEV ; + } + lt->regmap[i] =devm_regmap_init_i2c (lt->i2c_client[i], + <8912_regmap_config);Bad indentation.
Quoted 161 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +161
-0+if (IS_ERR (lt->regmap[i])) { + ret =PTR_ERR (lt->regmap[i]); +return ret; + } + } +return 0 ; +} + +static int lt8912_free_i2c (struct lt8912 *lt) +{ +unsigned int i; + +for (i =1 ; i <I2C_MAX_IDX ; i++) +i2c_unregister_device (lt->i2c_client[i]); + +return 0 ; +} + +static int lt8912_hard_power_on (struct lt8912 *lt) +{ +gpiod_set_value_cansleep (lt->gp_reset,0 ); +msleep (20 ); + +return 0 ; +} + +static void lt8912_hard_power_off (struct lt8912 *lt) +{ +gpiod_set_value_cansleep (lt->gp_reset,1 ); +msleep (20 ); + lt->is_power_on = false; +} + +static int lt8912_video_setup (struct lt8912 *lt) +{ +u32 hactive, h_total, hpw, hfp, hbp; +u32 vactive, v_total, vpw, vfp, vbp; +u8 settle =0x08 ; +int ret; + +if (!lt) +return -EINVAL ; + + hactive = lt->mode.hactive; + hfp = lt->mode.hfront_porch; + hpw = lt->mode.hsync_len; + hbp = lt->mode.hback_porch; + h_total = hactive + hfp + hpw + hbp; + + vactive = lt->mode.vactive; + vfp = lt->mode.vfront_porch; + vpw = lt->mode.vsync_len; + vbp = lt->mode.vback_porch; + v_total = vactive + vfp + vpw + vbp; + +if (vactive <=600 ) + settle =0x04 ; +else if (vactive ==1080 ) + settle =0x0a ; + + ret =regmap_write (lt->regmap[I2C_CEC_DSI ],0x10 ,0x01 ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x11 , settle); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x18 , hpw); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x19 , vpw); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x1c , hactive &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x1d , hactive >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x2f ,0x0c ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x34 , h_total &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x35 , h_total >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x36 , v_total &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x37 , v_total >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x38 , vbp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x39 , vbp >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3a , vfp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3b , vfp >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3c , hbp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3d , hbp >>8 ); + + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3e , hfp &0xff ); + ret |=regmap_write (lt->regmap[I2C_CEC_DSI ],0x3f , hfp >>8 ); + +return ret; +} + +static int lt8912_soft_power_on (struct lt8912 *lt) +{ +if (!lt->is_power_on) { +u32 lanes = lt->data_lanes; + +lt8912_write_init_config (lt); +regmap_write (lt->regmap[I2C_CEC_DSI ],0x13 , lanes &3 ); + +lt8912_write_mipi_basic_config (lt); + + lt->is_power_on = true; + } + +return 0 ; +} + +static int lt8912_video_on (struct lt8912 *lt) +{ +int ret; + + ret =lt8912_video_setup (lt); +if (ret <0 ) + goto end; + + ret =lt8912_write_dds_config (lt); +if (ret <0 ) + goto end; + + ret =lt8912_write_rxlogicres_config (lt); +if (ret <0 ) + goto end; + + ret =lt8912_write_lvds_config (lt); +if (ret <0 ) + goto end; + +end: +return ret; +} + +static enum drm_connector_status +lt8912_connector_detect (struct drm_connector *connector,bool force) +{ +struct lt8912 *lt =connector_to_lt8912 (connector); + +return drm_bridge_detect (lt->hdmi_port); +} + +static const struct drm_connector_funcs lt8912_connector_funcs = { + .detect = lt8912_connector_detect, + .fill_modes = drm_helper_probe_single_connector_modes, + .destroy = drm_connector_cleanup, + .reset = drm_atomic_helper_connector_reset, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +static enum drm_mode_status +lt8912_connector_mode_valid (struct drm_connector *connector, +struct drm_display_mode *mode) +{ +if (mode->clock >150000 ) +return MODE_CLOCK_HIGH ; + +if (mode->hdisplay >1920 ) +return MODE_BAD_HVALUE ; + +if (mode->vdisplay >1080 ) +return MODE_BAD_VVALUE ; + +return MODE_OK ;drivers/gpu/drm/bridge/lontium-lt8912.c line 402
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+} + +static int lt8912_connector_get_modes (struct drm_connector *connector) +{ +struct edid *edid; +int ret, num =0 ; +struct lt8912 *lt =connector_to_lt8912 (connector); +u32 bus_format =MEDIA_BUS_FMT_RGB888_1X24 ; + + edid =drm_bridge_get_edid (lt->hdmi_port, connector);Memory leak, edid is never free'd.
drivers/gpu/drm/bridge/lontium-lt8912.c line 410
Quoted 8 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +8
-0+if (edid) { +drm_connector_update_edid_property (connector, edid); + num =drm_add_edid_modes (connector, edid); + }else +return ret; + + ret =drm_display_info_set_bus_formats (&connector->display_info, + &bus_format,1 );Bad indentation.
Quoted 50 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +50
-0+if (ret) +return ret; + +return num; +} + +static const struct drm_connector_helper_funcs lt8912_connector_helper_funcs = { + .get_modes = lt8912_connector_get_modes, + .mode_valid = lt8912_connector_mode_valid, +}; + +static void lt8912_bridge_mode_set (struct drm_bridge *bridge, +const struct drm_display_mode *mode, +const struct drm_display_mode *adj) +{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); + +drm_display_mode_to_videomode (adj, <->mode); +} + +static void lt8912_bridge_enable (struct drm_bridge *bridge) +{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); + +lt8912_video_on (lt); +} + +static int lt8912_attach_dsi (struct lt8912 *lt) +{ +struct device *dev = lt->dev; +struct mipi_dsi_host *host; +struct mipi_dsi_device *dsi; +int ret =-1 ; +const struct mipi_dsi_device_info info = { .type ="lt8912" , + .channel =0 , + .node =NULL , + }; + + host =of_find_mipi_dsi_host_by_node (lt->host_node); +if (!host) { +dev_err (dev,"failed to find dsi host\n" ); +return -EPROBE_DEFER ; + } + + dsi =mipi_dsi_device_register_full (host, &info); +if (IS_ERR (dsi)) { + ret =PTR_ERR (dsi); +dev_err (dev,"failed to create dsi device (%d)\n" , ret); + goto err_dsi_device; + }drivers/gpu/drm/bridge/lontium-lt8912.c line 470
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ + lt->dsi = dsi; + + dsi->lanes = lt->data_lanes; + dsi->format =MIPI_DSI_FMT_RGB888 ; + + dsi->mode_flags =MIPI_DSI_MODE_VIDEO | +MIPI_DSI_MODE_VIDEO_BURST | +MIPI_DSI_MODE_LPM | +MIPI_DSI_MODE_EOT_PACKET ;Maybe align the 3 last lines with where the 1st one starts.
Quoted 23 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +23
-0+ + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +dev_err (dev,"failed to attach dsi to host\n" ); + goto err_dsi_attach; + } + +return 0 ; + +err_dsi_attach: +mipi_dsi_device_unregister (dsi); +err_dsi_device: +return ret; +} + +static void lt8912_detach_dsi (struct lt8912 *lt) +{ +mipi_dsi_detach (lt->dsi); +mipi_dsi_device_unregister (lt->dsi); +} + +static int lt8912_bridge_init (struct drm_bridge *bridge) +{drivers/gpu/drm/bridge/lontium-lt8912.c line 503
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+int ret; +struct lt8912 *lt =bridge_to_lt8912 (bridge); +struct drm_connector *connector = <->connector; + + +if (lt->hdmi_port->ops &DRM_BRIDGE_OP_DETECT ) { + connector->polled =DRM_CONNECTOR_POLL_HPD ; + }else { + connector->polled =DRM_CONNECTOR_POLL_CONNECT | +DRM_CONNECTOR_POLL_DISCONNECT ;Bad indentation.
Quoted 17 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +17
-0+ } + + + ret =drm_connector_init (bridge->dev, connector, + <8912_connector_funcs, + lt->hdmi_port->type); +if (ret) + goto exit; + +drm_connector_helper_add (connector, <8912_connector_helper_funcs); + + connector->dpms =DRM_MODE_DPMS_OFF ; +drm_connector_attach_encoder (connector, bridge->encoder); + + + ret =lt8912_hard_power_on (lt); +if (ret)drivers/gpu/drm/bridge/lontium-lt8912.c line 530
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ goto exit; + + ret =lt8912_soft_power_on (lt); + +exit: +return ret; +} + +static int lt8912_bridge_attach (struct drm_bridge *bridge, +enum drm_bridge_attach_flags flags)Bad indentation.
drivers/gpu/drm/bridge/lontium-lt8912.c line 539
Quoted 9 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +9
-0+{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); +int ret; + +/* No need to check the return of this function */ +drm_bridge_attach (lt->bridge.encoder, + lt->hdmi_port, + <->bridge, + flags);Bad indentation.
Quoted 23 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +23
-0+ +if (!(flags &DRM_BRIDGE_ATTACH_NO_CONNECTOR )) { + ret =lt8912_bridge_init (bridge); +if (ret) { +dev_err (lt->dev,"Failed to init bridge ! (%d)\n" , ret); +return ret; + } + } + + ret =lt8912_attach_dsi (lt); +if (ret) +return ret; + + lt->is_attached = true; + +return ret; +} + +static void lt8912_bridge_detach (struct drm_bridge *bridge) +{ +struct lt8912 *lt =bridge_to_lt8912 (bridge); + +if (lt->is_attached) {drivers/gpu/drm/bridge/lontium-lt8912.c line 572
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+lt8912_detach_dsi (lt); +lt8912_hard_power_off (lt); + } +} + +static const struct drm_bridge_funcs lt8912_bridge_funcs = { + .attach = lt8912_bridge_attach, + .detach = lt8912_bridge_detach, + .mode_set = lt8912_bridge_mode_set, + .enable = lt8912_bridge_enable,Have a look at the documentation around in drm_bridge_funcs[1], some additional functions have to be implemented. I think you can look at lt9611[2] & lt9611uxc[3] for inspiration.
[1] https://dri.freedesktop.org/docs/drm/gpu/drm-kms-helpers.html#bridge-operations
[2] https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/bridge/lontium-lt9611.c#L947
[3] https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/bridge/lontium-lt9611uxc.c#L542Quoted 81 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +81
-0+}; + +static int lt8912_parse_dt (struct lt8912 *lt) +{ +struct gpio_desc *gp_reset; +struct device *dev = lt->dev; +int ret =0 ; +struct device_node *port_node; +struct device_node *endpoint; + + gp_reset =devm_gpiod_get_optional (dev,"reset" ,GPIOD_OUT_HIGH ); +if (IS_ERR (gp_reset)) { + ret =PTR_ERR (gp_reset); +if (ret != -EPROBE_DEFER ) +dev_err (dev,"Failed to get reset gpio: %d\n" , ret); +return ret; + } + lt->gp_reset = gp_reset; + + + endpoint =of_graph_get_endpoint_by_regs (dev->of_node,0 ,-1 ); +if (IS_ERR (endpoint)) { + ret =PTR_ERR (endpoint); + goto end; + } + + lt->data_lanes =of_property_count_u32_elems (endpoint,"data-lanes" ); +of_node_put (endpoint); + + lt->host_node =of_graph_get_remote_node (dev->of_node,0 ,-1 ); +if (!lt->host_node) { +dev_err (lt->dev,"%s: Failed to get remote port\n" , __func__); + ret = -ENODEV ; + goto end; + } + + port_node =of_graph_get_remote_node (dev->of_node,1 ,-1 ); +if (!port_node) { +dev_err (lt->dev,"%s: Failed to get connector port\n" , __func__); + ret = -ENODEV ; + goto err_free_host_node; + } + + lt->hdmi_port =of_drm_find_bridge (port_node); +if (IS_ERR (lt->hdmi_port)) { +dev_err (lt->dev,"%s: Failed to get hdmi port\n" , __func__); + ret =PTR_ERR (lt->hdmi_port); +of_node_put (lt->host_node); + goto end; + } + +if (!of_device_is_compatible (port_node,"hdmi-connector" )) { +dev_err (lt->dev,"%s: Failed to get hdmi port\n" , __func__); + ret = -EINVAL ; + } + +of_node_put (port_node); + +end: +return ret; + +err_free_host_node: +of_node_put (lt->host_node); +return ret; +} + +static int lt8912_put_dt (struct lt8912 *lt) +{ +of_node_put (lt->host_node); +return 0 ; +} + +static int lt8912_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +static struct lt8912 *lt; +int ret =0 ; +struct device *dev = &client->dev; + + lt =devm_kzalloc (dev,sizeof (struct lt8912 ),GFP_KERNEL ); +if (!lt)Quoted 8 lines
drivers/gpu/drm/bridge/lontium-lt8912.c line 657
Quoted 4 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +4
-0+return -ENOMEM ; + + lt->dev = dev; + lt->i2c_client[0 ] = client;The
i2c_clientthat is created from the DT address and passed intolt8912_probewill be overwritten by the i2c clients created inlt8912_init_i2cbefore it is ever used.
Quoted 3 lines
I think you made a mistake here.
Thelt8912_init_i2cfunction only initializes the lt->i2c_client[1]. (You can check the if condition).
You are 100% correct.
Quoted 87 lines
Quoted 71 lines
A related issue is that this device has two I2C addresses, which doesn't fit super neatly into the I2C driver model[1]. Since both addresses can't be provided by the DT, method one doesn't fit this driver. Method 2 doesn't fit well either, since the I2C bus isn't internal to the device. And 3&4 are not applicable. I'd say the two options are #1 splitting this driver, #2 keeping it like it is. I'm leaning towards #2 since both addresses correspond to a physical chip.
[1] https://www.kernel.org/doc/html/latest/i2c/instantiating-devices.html
Quoted 42 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +42
-0+ + ret =lt8912_parse_dt (lt); +if (ret) + goto err_dt_parse; + + ret =lt8912_init_i2c (lt); +if (ret) + goto err_i2c; + +i2c_set_clientdata (client, lt); + + lt->bridge.funcs = <8912_bridge_funcs; + lt->bridge.of_node = dev->of_node; +drm_bridge_add (<->bridge); + +return 0 ; + +err_i2c: +lt8912_put_dt (lt); +err_dt_parse: +return ret; +} + +static int lt8912_remove (struct i2c_client *client) +{ +struct lt8912 *lt =i2c_get_clientdata (client); + +lt8912_bridge_detach (<->bridge); +drm_bridge_remove (<->bridge); +lt8912_free_i2c (lt); +lt8912_put_dt (lt); + +return 0 ; +} + +static const struct of_device_id lt8912_dt_match[] = { + {.compatible ="lontium,lt8912" }, + {} +}; +MODULE_DEVICE_TABLE (of, lt8912_dt_match); + +static const struct i2c_device_id lt8912_id[] = {drivers/gpu/drm/bridge/lontium-lt8912.c line 709
Quoted 10 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-0+ {"lt8912", 0}, + {}, +}; +MODULE_DEVICE_TABLE(i2c, lt8912_id); + +static struct i2c_driver lt8912_i2c_driver = { + .driver = { + .name = "lt8912", + .of_match_table = lt8912_dt_match, + .owner = THIS_MODULE,The .owner assignment is redundant as it is later re-assigned in[1].
module_i2c_driver->i2c_add_driver->i2c_register_driver[1] https://elixir.bootlin.com/linux/latest/source/drivers/i2c/i2c-core-base.c#L1796
Quoted 13 lines
Quoted 11 lines
drivers/gpu/drm/bridge/lontium-lt8912.c new file +10
-1+ }, + .probe = lt8912_probe, + .remove = lt8912_remove, + .id_table = lt8912_id, +}; +module_i2c_driver (lt8912_i2c_driver); + +MODULE_AUTHOR ("Adrien Grassein <[email protected]>" ); +MODULE_DESCRIPTION ("lt8912 drm driver" ); +MODULE_LICENSE ("GPL v2" ); --Quoted 2 lines
2.25.1
I will send a new version with the fixes.
Quoted 2 lines
Thanks again,
Adrien Grassein
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel