pinctrl: armada-37xx: Correct PWM pins definitions

PATCH In review Marek Behún 2 participants 2 messages Jul 19, 2021 – Jul 23, 2021

Subsystems (4)

Device tree bindings GPIO Pin control Arm/Marvell Kirkwood and Armada 370, 375, 38x, 39x, XP, 3700, 7K/8K, CN9130 SoC support

lore

Share & tools

lore

Marek Behún

author

2021-07-19 11:29 UTC #0 lore raw

PATCH v2 1/1 pinctrl: armada-37xx: Correct PWM pins definitions

The PWM pins on North Bridge on Armada 37xx can be configured into PWM or GPIO functions. When in PWM function, each pin can also be configured to drive low on 0 and tri-state on 1 (LED mode).

The current definitions handle this by declaring two pin groups for each pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"

This is semantically incorrect. The correct definition for each pin should be one group with three functions: "pwm", "led" and "gpio".

Change the "pwmN" groups to support "led" function.

Remove "ledN_od" groups. This cannot break backwards compatibility with older device trees: no device tree uses it since there is no PWM driver for this SOC yet. Also "ledN_od" groups are not even documented.

Fixes b835d6953009 ("pinctrl: armada-37xx: swap polarity on LED group")

Signed-off-by Marek Behún <[email protected]>

Acked-by Rob Herring <[email protected]>

---
Since v1 I've added Fixes tag and Rob's Acked-by.

---
 .../pinctrl/marvell,armada-37xx-pinctrl.txt      |  8 ++++----
 drivers/pinctrl/mvebu/pinctrl-armada-37xx.c      | 16 ++++++++--------
 2 files changed, 12 insertions(+), 12 deletions(-)

Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt +4 -4

index 38dc56a57760..ecec514b3155 100644
@@ -43,19 +43,19 @@ group emmc_nb
 
 group pwm0
  - pin 11 (GPIO1-11)
- - functions pwm, gpio
+ - functions pwm, led, gpio
 
 group pwm1
  - pin 12
- - functions pwm, gpio
+ - functions pwm, led, gpio
 
 group pwm2
  - pin 13
- - functions pwm, gpio
+ - functions pwm, led, gpio
 
 group pwm3
  - pin 14
- - functions pwm, gpio
+ - functions pwm, led, gpio
 
 group pmic1
  - pin 7

drivers/pinctrl/mvebu/pinctrl-armada-37xx.c +8 -8

index 5a68e242f6b3..5cb018f98800 100644
@@ -167,10 +167,14 @@ static struct armada_37xx_pin_group armada_37xx_nb_groups[] = {
 	PIN_GRP_GPIO("jtag", 20, 5, BIT(0), "jtag"),
 	PIN_GRP_GPIO("sdio0", 8, 3, BIT(1), "sdio"),
 	PIN_GRP_GPIO("emmc_nb", 27, 9, BIT(2), "emmc"),
-	PIN_GRP_GPIO("pwm0", 11, 1, BIT(3), "pwm"),
-	PIN_GRP_GPIO("pwm1", 12, 1, BIT(4), "pwm"),
-	PIN_GRP_GPIO("pwm2", 13, 1, BIT(5), "pwm"),
-	PIN_GRP_GPIO("pwm3", 14, 1, BIT(6), "pwm"),
+	PIN_GRP_GPIO_3("pwm0", 11, 1, BIT(3) | BIT(20), 0, BIT(20), BIT(3),
+		       "pwm", "led"),
+	PIN_GRP_GPIO_3("pwm1", 12, 1, BIT(4) | BIT(21), 0, BIT(21), BIT(4),
+		       "pwm", "led"),
+	PIN_GRP_GPIO_3("pwm2", 13, 1, BIT(5) | BIT(22), 0, BIT(22), BIT(5),
+		       "pwm", "led"),
+	PIN_GRP_GPIO_3("pwm3", 14, 1, BIT(6) | BIT(23), 0, BIT(23), BIT(6),
+		       "pwm", "led"),
 	PIN_GRP_GPIO("pmic1", 7, 1, BIT(7), "pmic"),
 	PIN_GRP_GPIO("pmic0", 6, 1, BIT(8), "pmic"),
 	PIN_GRP_GPIO("i2c2", 2, 2, BIT(9), "i2c"),

@@ -184,10 +188,6 @@ static struct armada_37xx_pin_group armada_37xx_nb_groups[] = {
 	PIN_GRP_EXTRA("uart2", 9, 2, BIT(1) | BIT(13) | BIT(14) | BIT(19),
 		      BIT(1) | BIT(13) | BIT(14), BIT(1) | BIT(19),
 		      18, 2, "gpio", "uart"),
-	PIN_GRP_GPIO_2("led0_od", 11, 1, BIT(20), BIT(20), 0, "led"),
-	PIN_GRP_GPIO_2("led1_od", 12, 1, BIT(21), BIT(21), 0, "led"),
-	PIN_GRP_GPIO_2("led2_od", 13, 1, BIT(22), BIT(22), 0, "led"),
-	PIN_GRP_GPIO_2("led3_od", 14, 1, BIT(23), BIT(23), 0, "led"),
 };
 
 static struct armada_37xx_pin_group armada_37xx_sb_groups[] = {

Signature · 1 line

2.31.1

Linus Walleij

2021-07-23 15:55 UTC #1 lore raw

Quoted 18 lines · Marek Behún

The PWM pins on North Bridge on Armada 37xx can be configured into PWM or GPIO functions. When in PWM function, each pin can also be configured to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with older device trees: no device tree uses it since there is no PWM driver for this SOC yet. Also "ledN_od" groups are not even documented.

Quoted 5 lines

Fixes b835d6953009 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by Marek Behún <[email protected]>
Acked-by Rob Herring <[email protected]>
---
Since v1 I've added Fixes tag and Rob's Acked-by.

Patch applied, sorry for taking such time with this.

Yours,
Linus Walleij