Skip to contentSkip to conversation

net: stmmac: dwmac-rk: use stmmac helper functions and clean up

RFC PATCH In review Michael Riesch 3 participants 7 messages Sep 15, 2021 – Sep 21, 2021

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover net: stmmac: dwmac-rk: use stmmac helper functions and clean up

Hi all,

This series aims to clean up the dwmac-rk glue driver by making the stmmac core responsible for clock and power management. The dwmac-rk specific code is passed to the core via callbacks. The patches have been tested successfully on a RK3568 EVB1.

With any luck, the patches fix the Ethernet regression on different RK3399 boards, which has been introduced recently in v5.14 -- but don't be disappointed if that is not the case :-)

The series is marked as RFC since the handling of the (internal) phy is not quite clear yet. Should rk_gmac_{init,exit} still consider device_may_wakeup at some point? Should the glue driver power on/off the external phy in the first place? Or will the stmmac core take care of it?

Also, I am sending this RFC to linux-rockchip exclusively on purpose as I would like to see some test results on other boards before proceeding.

As an addition, the usage of clk_bulk_* functions is envisaged but not yet implemented due to time constraints.

Looking forward to your comments!

Best regards,
Michael

Michael Riesch (3):
net: stmmac: dwmac-rk: use stmmac helper functions for pm ops and
remove
net: stmmac: dwmac-rk: clean up includes
net: stmmac: dwmac-rk: use stmmac helper functions for clock
management

 .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 117 +++++-------------
 1 file changed, 32 insertions(+), 85 deletions(-)
Signature · 7 lines
2.17.1


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#1 lore raw

RFC PATCH 1/3 net: stmmac: dwmac-rk: use stmmac helper functions for pm ops and remove

Make the stmmac core responsible for suspend, resume and remove by providing callbacks and using helper functions.

---
 .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 69 +++++--------------
 1 file changed, 16 insertions(+), 53 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c +16 -53
index ed817011a94a..0db8be543ee1 100644
@@ -40,7 +40,6 @@ struct rk_priv_data {
 	phy_interface_t phy_iface;
 	int id;
 	struct regulator *regulator;
-	bool suspended;
 	const struct rk_gmac_ops *ops;
 
 	bool clk_enabled;
@@ -1482,10 +1481,11 @@ static int rk_gmac_check_ops(struct rk_priv_data *bsp_priv)
 	return 0;
 }
 
-static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
+static int rk_gmac_init(struct platform_device *pdev, void *priv)
 {
 	int ret;
-	struct device *dev = &bsp_priv->pdev->dev;
+	struct device *dev = &pdev->dev;
+	struct rk_priv_data *bsp_priv = priv;
 
 	ret = rk_gmac_check_ops(bsp_priv);
 	if (ret)
@@ -1534,13 +1534,15 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 	return 0;
 }
 
-static void rk_gmac_powerdown(struct rk_priv_data *gmac)
+static void rk_gmac_exit(struct platform_device *pdev, void *priv)
 {
-	if (gmac->integrated_phy)
-		rk_gmac_integrated_phy_powerdown(gmac);
+	struct rk_priv_data *bsp_priv = priv;
 
-	phy_power_on(gmac, false);
-	gmac_clk_enable(gmac, false);
+	if (bsp_priv->integrated_phy)
+		rk_gmac_integrated_phy_powerdown(bsp_priv);
+
+	phy_power_on(bsp_priv, false);
+	gmac_clk_enable(bsp_priv, false);
 }
 
 static void rk_fix_speed(void *priv, unsigned int speed)
@@ -1591,6 +1593,8 @@ static int rk_gmac_probe(struct platform_device *pdev)
 	 */
 	if (!plat_dat->has_gmac4)
 		plat_dat->has_gmac = true;
+	plat_dat->init = rk_gmac_init;
+	plat_dat->exit = rk_gmac_exit;
 	plat_dat->fix_mac_speed = rk_fix_speed;
 
 	plat_dat->bsp_priv = rk_gmac_setup(pdev, plat_dat, data);
@@ -1603,7 +1607,7 @@ static int rk_gmac_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_remove_config_dt;
 
-	ret = rk_gmac_powerup(plat_dat->bsp_priv);
+	ret = rk_gmac_init(pdev, plat_dat->bsp_priv);
 	if (ret)
 		goto err_remove_config_dt;
 
@@ -1614,54 +1618,13 @@ static int rk_gmac_probe(struct platform_device *pdev)
 	return 0;
 
 err_gmac_powerdown:
-	rk_gmac_powerdown(plat_dat->bsp_priv);
+	rk_gmac_exit(pdev, plat_dat->bsp_priv);
 err_remove_config_dt:
 	stmmac_remove_config_dt(pdev, plat_dat);
 
 	return ret;
 }
 
-static int rk_gmac_remove(struct platform_device *pdev)
-{
-	struct rk_priv_data *bsp_priv = get_stmmac_bsp_priv(&pdev->dev);
-	int ret = stmmac_dvr_remove(&pdev->dev);
-
-	rk_gmac_powerdown(bsp_priv);
-
-	return ret;
-}
-
-#ifdef CONFIG_PM_SLEEP
-static int rk_gmac_suspend(struct device *dev)
-{
-	struct rk_priv_data *bsp_priv = get_stmmac_bsp_priv(dev);
-	int ret = stmmac_suspend(dev);
-
-	/* Keep the PHY up if we use Wake-on-Lan. */
-	if (!device_may_wakeup(dev)) {
-		rk_gmac_powerdown(bsp_priv);
-		bsp_priv->suspended = true;
-	}
-
-	return ret;
-}
-
-static int rk_gmac_resume(struct device *dev)
-{
-	struct rk_priv_data *bsp_priv = get_stmmac_bsp_priv(dev);
-
-	/* The PHY was up for Wake-on-Lan. */
-	if (bsp_priv->suspended) {
-		rk_gmac_powerup(bsp_priv);
-		bsp_priv->suspended = false;
-	}
-
-	return stmmac_resume(dev);
-}
-#endif /* CONFIG_PM_SLEEP */
-
-static SIMPLE_DEV_PM_OPS(rk_gmac_pm_ops, rk_gmac_suspend, rk_gmac_resume);
-
 static const struct of_device_id rk_gmac_dwmac_match[] = {
 	{ .compatible = "rockchip,px30-gmac",	.data = &px30_ops   },
 	{ .compatible = "rockchip,rk3128-gmac", .data = &rk3128_ops },
@@ -1680,10 +1643,10 @@ MODULE_DEVICE_TABLE(of, rk_gmac_dwmac_match);
 
 static struct platform_driver rk_gmac_dwmac_driver = {
 	.probe  = rk_gmac_probe,
-	.remove = rk_gmac_remove,
+	.remove = stmmac_pltfr_remove,
 	.driver = {
 		.name           = "rk_gmac-dwmac",
-		.pm		= &rk_gmac_pm_ops,
+		.pm		= &stmmac_pltfr_pm_ops,
 		.of_match_table = rk_gmac_dwmac_match,
 	},
 };
Signature · 7 lines
2.17.1


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
maintainer
#2 lore raw

Re: [RFC PATCH 1/3] net: stmmac: dwmac-rk: use stmmac helper functions for pm ops and remove

Hi,

Am Mittwoch, 15. September 2021, 19:02:53 CEST schrieb Michael Riesch:

Quoted 4 lines

Make the stmmac core responsible for suspend, resume and remove by providing callbacks and using helper functions.

this would likely loose wake-on-lan functionality?

Right now the homebrew suspend/resume functions handle the device_may_wakeup()-case as well, where the ->init and ->exit functions seem to get called from stmmac_pltfr_suspend / stmmac_pltfr_resume unconditionally instead.

While I've never tried wake-on-lan myself, this really looks like this patch would loose the functionality.

Heiko

Quoted 129 lines
---
 .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 69 +++++--------------
 1 file changed, 16 insertions(+), 53 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c +14 -51
index ed817011a94a..0db8be543ee1 100644
@@ -40,7 +40,6 @@ struct rk_priv_data {
 	phy_interface_t phy_iface;
 	int id;
 	struct regulator *regulator;
-	bool suspended;
 	const struct rk_gmac_ops *ops;
 
 	bool clk_enabled;
@@ -1482,10 +1481,11 @@ static int rk_gmac_check_ops(struct rk_priv_data *bsp_priv)
 	return 0;
 }
 
-static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
+static int rk_gmac_init(struct platform_device *pdev, void *priv)
 {
 	int ret;
-	struct device *dev = &bsp_priv->pdev->dev;
+	struct device *dev = &pdev->dev;
+	struct rk_priv_data *bsp_priv = priv;
 
 	ret = rk_gmac_check_ops(bsp_priv);
 	if (ret)
@@ -1534,13 +1534,15 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 	return 0;
 }
 
-static void rk_gmac_powerdown(struct rk_priv_data *gmac)
+static void rk_gmac_exit(struct platform_device *pdev, void *priv)
 {
-	if (gmac->integrated_phy)
-		rk_gmac_integrated_phy_powerdown(gmac);
+	struct rk_priv_data *bsp_priv = priv;
 
-	phy_power_on(gmac, false);
-	gmac_clk_enable(gmac, false);
+	if (bsp_priv->integrated_phy)
+		rk_gmac_integrated_phy_powerdown(bsp_priv);
+
+	phy_power_on(bsp_priv, false);
+	gmac_clk_enable(bsp_priv, false);
 }
 
 static void rk_fix_speed(void *priv, unsigned int speed)
@@ -1591,6 +1593,8 @@ static int rk_gmac_probe(struct platform_device *pdev)
 	 */
 	if (!plat_dat->has_gmac4)
 		plat_dat->has_gmac = true;
+	plat_dat->init = rk_gmac_init;
+	plat_dat->exit = rk_gmac_exit;
 	plat_dat->fix_mac_speed = rk_fix_speed;
 
 	plat_dat->bsp_priv = rk_gmac_setup(pdev, plat_dat, data);
@@ -1603,7 +1607,7 @@ static int rk_gmac_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_remove_config_dt;
 
-	ret = rk_gmac_powerup(plat_dat->bsp_priv);
+	ret = rk_gmac_init(pdev, plat_dat->bsp_priv);
 	if (ret)
 		goto err_remove_config_dt;
 
@@ -1614,54 +1618,13 @@ static int rk_gmac_probe(struct platform_device *pdev)
 	return 0;
 
 err_gmac_powerdown:
-	rk_gmac_powerdown(plat_dat->bsp_priv);
+	rk_gmac_exit(pdev, plat_dat->bsp_priv);
 err_remove_config_dt:
 	stmmac_remove_config_dt(pdev, plat_dat);
 
 	return ret;
 }
 
-static int rk_gmac_remove(struct platform_device *pdev)
-{
-	struct rk_priv_data *bsp_priv = get_stmmac_bsp_priv(&pdev->dev);
-	int ret = stmmac_dvr_remove(&pdev->dev);
-
-	rk_gmac_powerdown(bsp_priv);
-
-	return ret;
-}
-
-#ifdef CONFIG_PM_SLEEP
-static int rk_gmac_suspend(struct device *dev)
-{
-	struct rk_priv_data *bsp_priv = get_stmmac_bsp_priv(dev);
-	int ret = stmmac_suspend(dev);
-
-	/* Keep the PHY up if we use Wake-on-Lan. */
-	if (!device_may_wakeup(dev)) {
-		rk_gmac_powerdown(bsp_priv);
-		bsp_priv->suspended = true;
-	}
-
-	return ret;
-}
-
-static int rk_gmac_resume(struct device *dev)
-{
-	struct rk_priv_data *bsp_priv = get_stmmac_bsp_priv(dev);
-
-	/* The PHY was up for Wake-on-Lan. */
-	if (bsp_priv->suspended) {
-		rk_gmac_powerup(bsp_priv);
-		bsp_priv->suspended = false;
-	}
-
-	return stmmac_resume(dev);
-}
-#endif /* CONFIG_PM_SLEEP */
-
-static SIMPLE_DEV_PM_OPS(rk_gmac_pm_ops, rk_gmac_suspend, rk_gmac_resume);
-
 static const struct of_device_id rk_gmac_dwmac_match[] = {
 	{ .compatible = "rockchip,px30-gmac",	.data = &px30_ops   },
 	{ .compatible = "rockchip,rk3128-gmac", .data = &rk3128_ops },
@@ -1680,10 +1643,10 @@ MODULE_DEVICE_TABLE(of, rk_gmac_dwmac_match);
 
 static struct platform_driver rk_gmac_dwmac_driver = {

drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c MODULE_DEVICE_TABLE(of, rk_gmac_dwmac_match); · line 1652

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c +2 -2
 	.probe  = rk_gmac_probe,
-	.remove = rk_gmac_remove,
+	.remove = stmmac_pltfr_remove,
 	.driver = {
 		.name           = "rk_gmac-dwmac",
-		.pm		= &rk_gmac_pm_ops,
+		.pm		= &stmmac_pltfr_pm_ops,
 		.of_match_table = rk_gmac_dwmac_match,
 	},
 };

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip

#3 lore raw

RFC PATCH 2/3 net: stmmac: dwmac-rk: clean up includes

In reply to Michael Riesch

Sort includes alphabetically and remove unused includes.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c | 14 +++++---------
 1 file changed, 5 insertions(+), 9 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c +5 -9
index 0db8be543ee1..96ec7d73a74a 100644
@@ -7,20 +7,16 @@
  * Chen-Zhi (Roger Chen)  <[email protected]>
  */
 
-#include <linux/stmmac.h>
-#include <linux/bitops.h>
 #include <linux/clk.h>
-#include <linux/phy.h>
-#include <linux/of_net.h>
-#include <linux/gpio.h>
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
-#include <linux/of_gpio.h>
 #include <linux/of_device.h>
+#include <linux/of_net.h>
+#include <linux/phy.h>
 #include <linux/platform_device.h>
-#include <linux/regulator/consumer.h>
-#include <linux/delay.h>
-#include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/stmmac.h>
 
 #include "stmmac_platform.h"
 
Signature · 7 lines
2.17.1


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
maintainer Reviewed-by on v1 2/3
#4 lore raw

Re: [RFC PATCH 2/3] net: stmmac: dwmac-rk: clean up includes

Am Mittwoch, 15. September 2021, 19:02:54 CEST schrieb Michael Riesch:

Quoted 3 lines

Sort includes alphabetically and remove unused includes.

This is nice in its own right

Quoted 25 lines
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c | 14 +++++---------
 1 file changed, 5 insertions(+), 9 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c +3 -6
index 0db8be543ee1..96ec7d73a74a 100644
@@ -7,20 +7,16 @@
  * Chen-Zhi (Roger Chen)  <[email protected]>
  */
 
-#include <linux/stmmac.h>
-#include <linux/bitops.h>
 #include <linux/clk.h>
-#include <linux/phy.h>
-#include <linux/of_net.h>
-#include <linux/gpio.h>
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
-#include <linux/of_gpio.h>
 #include <linux/of_device.h>
+#include <linux/of_net.h>
+#include <linux/phy.h>

drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c line 22

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c +2 -3
 #include <linux/platform_device.h>
-#include <linux/regulator/consumer.h>
-#include <linux/delay.h>
-#include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/stmmac.h>
 
 #include "stmmac_platform.h"
 

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip

#5 lore raw

RFC PATCH 3/3 net: stmmac: dwmac-rk: use stmmac helper functions for clock management

In reply to Michael Riesch

Make the stmmac core responsible for the management of the stmmaceth clock (directly) and the dwmac-rk specific clocks (via a the clks_config callback function).

---
 .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 38 +++++++------------
 1 file changed, 13 insertions(+), 25 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c +13 -25
index 96ec7d73a74a..0a66c3b589b1 100644
@@ -42,7 +42,6 @@ struct rk_priv_data {
 	bool clock_input;
 	bool integrated_phy;
 
-	struct clk *clk_mac;
 	struct clk *gmac_clkin;
 	struct clk *mac_clk_rx;
 	struct clk *mac_clk_tx;
@@ -1217,11 +1216,6 @@ static int rk_gmac_clk_init(struct plat_stmmacenet_data *plat)
 		dev_err(dev, "cannot get clock %s\n",
 			"pclk_mac");
 
-	bsp_priv->clk_mac = devm_clk_get(dev, "stmmaceth");
-	if (IS_ERR(bsp_priv->clk_mac))
-		dev_err(dev, "cannot get clock %s\n",
-			"stmmaceth");
-
 	if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RMII) {
 		bsp_priv->clk_mac_ref = devm_clk_get(dev, "clk_mac_ref");
 		if (IS_ERR(bsp_priv->clk_mac_ref))
@@ -1245,7 +1239,7 @@ static int rk_gmac_clk_init(struct plat_stmmacenet_data *plat)
 		dev_info(dev, "clock input from PHY\n");
 	} else {
 		if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RMII)
-			clk_set_rate(bsp_priv->clk_mac, 50000000);
+			clk_set_rate(plat->stmmac_clk, 50000000);
 	}
 
 	if (plat->phy_node && bsp_priv->integrated_phy) {
@@ -1261,8 +1255,9 @@ static int rk_gmac_clk_init(struct plat_stmmacenet_data *plat)
 	return 0;
 }
 
-static int gmac_clk_enable(struct rk_priv_data *bsp_priv, bool enable)
+static int rk_gmac_clks_config(void *priv, bool enable)
 {
+	struct rk_priv_data *bsp_priv = priv;
 	int phy_iface = bsp_priv->phy_iface;
 
 	if (enable) {
@@ -1296,10 +1291,6 @@ static int gmac_clk_enable(struct rk_priv_data *bsp_priv, bool enable)
 			if (!IS_ERR(bsp_priv->clk_mac_speed))
 				clk_prepare_enable(bsp_priv->clk_mac_speed);
 
-			/**
-			 * if (!IS_ERR(bsp_priv->clk_mac))
-			 *	clk_prepare_enable(bsp_priv->clk_mac);
-			 */
 			mdelay(5);
 			bsp_priv->clk_enabled = true;
 		}
@@ -1322,10 +1313,7 @@ static int gmac_clk_enable(struct rk_priv_data *bsp_priv, bool enable)
 			clk_disable_unprepare(bsp_priv->mac_clk_tx);
 
 			clk_disable_unprepare(bsp_priv->clk_mac_speed);
-			/**
-			 * if (!IS_ERR(bsp_priv->clk_mac))
-			 *	clk_disable_unprepare(bsp_priv->clk_mac);
-			 */
+
 			bsp_priv->clk_enabled = false;
 		}
 	}
@@ -1487,10 +1475,6 @@ static int rk_gmac_init(struct platform_device *pdev, void *priv)
 	if (ret)
 		return ret;
 
-	ret = gmac_clk_enable(bsp_priv, true);
-	if (ret)
-		return ret;
-
 	/*rmii or rgmii*/
 	switch (bsp_priv->phy_iface) {
 	case PHY_INTERFACE_MODE_RGMII:
@@ -1519,10 +1503,8 @@ static int rk_gmac_init(struct platform_device *pdev, void *priv)
 	}
 
 	ret = phy_power_on(bsp_priv, true);
-	if (ret) {
-		gmac_clk_enable(bsp_priv, false);
+	if (ret)
 		return ret;
-	}
 
 	if (bsp_priv->integrated_phy)
 		rk_gmac_integrated_phy_powerup(bsp_priv);
@@ -1538,7 +1520,6 @@ static void rk_gmac_exit(struct platform_device *pdev, void *priv)
 		rk_gmac_integrated_phy_powerdown(bsp_priv);
 
 	phy_power_on(bsp_priv, false);
-	gmac_clk_enable(bsp_priv, false);
 }
 
 static void rk_fix_speed(void *priv, unsigned int speed)
@@ -1591,6 +1572,7 @@ static int rk_gmac_probe(struct platform_device *pdev)
 		plat_dat->has_gmac = true;
 	plat_dat->init = rk_gmac_init;
 	plat_dat->exit = rk_gmac_exit;
+	plat_dat->clks_config = rk_gmac_clks_config;
 	plat_dat->fix_mac_speed = rk_fix_speed;
 
 	plat_dat->bsp_priv = rk_gmac_setup(pdev, plat_dat, data);
@@ -1603,10 +1585,14 @@ static int rk_gmac_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_remove_config_dt;
 
-	ret = rk_gmac_init(pdev, plat_dat->bsp_priv);
+	ret = rk_gmac_clks_config(plat_dat->bsp_priv, true);
 	if (ret)
 		goto err_remove_config_dt;
 
+	ret = rk_gmac_init(pdev, plat_dat->bsp_priv);
+	if (ret)
+		goto err_gmac_clks_off;
+
 	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
 	if (ret)
 		goto err_gmac_powerdown;
@@ -1615,6 +1601,8 @@ static int rk_gmac_probe(struct platform_device *pdev)
 
 err_gmac_powerdown:
 	rk_gmac_exit(pdev, plat_dat->bsp_priv);
+err_gmac_clks_off:
+	rk_gmac_clks_config(plat_dat->bsp_priv, true);
 err_remove_config_dt:
 	stmmac_remove_config_dt(pdev, plat_dat);
 
Signature · 7 lines
2.17.1


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#6 lore raw
In reply to Michael Riesch

Hi Michael,

Quoted 10 lines · Michael Riesch

Hi all,

This series aims to clean up the dwmac-rk glue driver by making the stmmac core responsible for clock and power management. The dwmac-rk specific code is passed to the core via callbacks. The patches have been tested successfully on a RK3568 EVB1.

With any luck, the patches fix the Ethernet regression on different RK3399 boards, which has been introduced recently in v5.14 -- but don't be disappointed if that is not the case :-)

I did a quick test run - the ethernet is still buggered on RockPro64 for me.

Thanks,
Punit

[...]

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip