Skip to contentSkip to conversation

arm: kirkwood: Add support for Pogoplug V4

PATCH Superseded Tony Dinh 2 participants 8 messages Jan 21, 2022 – Jan 23, 2022

Subsystems (2)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore

Tony Dinh

author
#0 lore raw

v4 cover arm: kirkwood: Add support for Pogoplug V4

Pogoplug V4 specifications:

Kirkwood 88F6192 SoC
800 MHz CPU
1Gbs Ethernet
128 MB RAM
128 MB NAND
1x USB 2.0
2x USB 3.0 (on PCIe bus)
1 SDHC slot
1x External SATA port (USM enclosure form factor slot)

Changes in v4:
- Remove CONFIG_FEATURE_COMMAND_EDITING and ifdefs for CMD_NET in include header

Changes in v3:
- Migrate symbols from board include header to Kconfig
- Squash board file small patches into one patch
- Migrate config symbols from board include header to defconfig
- Remove obsolete config symbols from header file
- Don't use ifdefs for unselectable config symbols in header file

Changes in v2:
- Use mainline Linux DTS version
- Move constants to .c file and remove header file
- Use canonical format for defconfig file

Tony Dinh (4):
arm: kirkwood: Pogoplug-V4 : Add DTS files
arm: kirkwood: Pogoplug-V4 : Add Kconfig files
arm: kirkwood: Pogoplug-V4 : Add board implementation files
arm: kirkwood: Pogoplug V4 : Add board include header and defconfig
files

 arch/arm/dts/Makefile                       |   1 +
 arch/arm/dts/kirkwood-pogoplug-series-4.dts | 180 ++++++++++++++++
 arch/arm/mach-kirkwood/Kconfig              |   6 +
 board/cloudengines/pogo_v4/Kconfig          |  16 ++
 board/cloudengines/pogo_v4/MAINTAINERS      |   6 +
 board/cloudengines/pogo_v4/Makefile         |  10 +
 board/cloudengines/pogo_v4/kwbimage.cfg     | 148 +++++++++++++
 board/cloudengines/pogo_v4/pogo_v4.c        | 220 ++++++++++++++++++++
 configs/pogo_v4_defconfig                   |  79 +++++++
 include/configs/pogo_v4.h                   |  53 +++++
 10 files changed, 719 insertions(+)
 create mode 100644 arch/arm/dts/kirkwood-pogoplug-series-4.dts
 create mode 100644 board/cloudengines/pogo_v4/Kconfig
 create mode 100644 board/cloudengines/pogo_v4/MAINTAINERS
 create mode 100644 board/cloudengines/pogo_v4/Makefile
 create mode 100644 board/cloudengines/pogo_v4/kwbimage.cfg
 create mode 100644 board/cloudengines/pogo_v4/pogo_v4.c
 create mode 100644 configs/pogo_v4_defconfig
 create mode 100644 include/configs/pogo_v4.h
Signature · 1 line
2.30.2
author
#1 lore raw

PATCH v4 1/4 arm: kirkwood: Pogoplug-V4 : Add DTS files

Add DTS files for Pogoplug V4 board

---

(no changes since v2)

Changes in v2:
- Use mainline Linux DTS version

 arch/arm/dts/Makefile                       |   1 +
 arch/arm/dts/kirkwood-pogoplug-series-4.dts | 180 ++++++++++++++++++++
 2 files changed, 181 insertions(+)
 create mode 100644 arch/arm/dts/kirkwood-pogoplug-series-4.dts
arch/arm/dts/Makefile +1 -0
index 1b65e65eb8..ce33a4b52b 100644
@@ -71,6 +71,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += \
 	kirkwood-openrd-client.dtb \
 	kirkwood-openrd-ultimate.dtb \
 	kirkwood-pogo_e02.dtb \
+	kirkwood-pogoplug-series-4.dtb \
 	kirkwood-sheevaplug.dtb
 
 dtb-$(CONFIG_MACH_S900) += \
arch/arm/dts/kirkwood-pogoplug-series-4.dts new file +180 -0

180 lines not on this page · raw message

Signature · 1 line
2.30.2
author
#2 lore raw

PATCH v4 2/4 arm: kirkwood: Pogoplug-V4 : Add Kconfig files

In reply to Tony Dinh

Add Kconfig files for Pogoplug V4 board

---

(no changes since v3)

Changes in v3:
- Migrate symbols from board include header to Kconfig

 arch/arm/mach-kirkwood/Kconfig     |  6 ++++++
 board/cloudengines/pogo_v4/Kconfig | 16 ++++++++++++++++
 2 files changed, 22 insertions(+)
 create mode 100644 board/cloudengines/pogo_v4/Kconfig
arch/arm/mach-kirkwood/Kconfig +6 -0
index c060cc8546..382b836267 100644
@@ -51,6 +51,11 @@ config TARGET_POGO_E02
 	select FEROCEON_88FR131
 	select KW88F6281
 
+config TARGET_POGO_V4
+	bool "Pogoplug V4 Board"
+	select FEROCEON_88FR131
+	select KW88F6192
+
 config TARGET_DNS325
 	bool "dns325 Board"
 	select FEROCEON_88FR131
@@ -123,6 +128,7 @@ source "board/Marvell/guruplug/Kconfig"
 source "board/Marvell/sheevaplug/Kconfig"
 source "board/buffalo/lsxl/Kconfig"
 source "board/cloudengines/pogo_e02/Kconfig"
+source "board/cloudengines/pogo_v4/Kconfig"
 source "board/d-link/dns325/Kconfig"
 source "board/iomega/iconnect/Kconfig"
 source "board/keymile/Kconfig"
board/cloudengines/pogo_v4/Kconfig new file +16 -0
new file mode 100644
index 0000000000..db3b76b4d4
@@ -0,0 +1,16 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2014-2021 Tony Dinh <[email protected]>
+#
+if TARGET_POGO_V4
+
+config SYS_BOARD
+	default "pogo_v4"
+
+config SYS_VENDOR
+	default "cloudengines"
+
+config SYS_CONFIG_NAME
+	default "pogo_v4"
+
+endif
Signature · 1 line
2.30.2
author
#3 lore raw

PATCH v4 3/4 arm: kirkwood: Pogoplug-V4 : Add board implementation files

In reply to Tony Dinh

Note: currently the fdt_get_phy_addr function in this file is duplicate in this board and many other Kirkwood boards (eg. Sheevaplug, GoFlex Home, etc.). This function is being factored out into common area by another patch. And because it was written for flattree only, the patch is being rewritten to use livetree calls.

---

(no changes since v3)

Changes in v3:
- Squash board file small patches into one patch

Changes in v2:
- Move constants to .c file and remove header file

 board/cloudengines/pogo_v4/MAINTAINERS  |   6 +
 board/cloudengines/pogo_v4/Makefile     |  10 ++
 board/cloudengines/pogo_v4/kwbimage.cfg | 148 ++++++++++++++++
 board/cloudengines/pogo_v4/pogo_v4.c    | 220 ++++++++++++++++++++++++
 4 files changed, 384 insertions(+)
 create mode 100644 board/cloudengines/pogo_v4/MAINTAINERS
 create mode 100644 board/cloudengines/pogo_v4/Makefile
 create mode 100644 board/cloudengines/pogo_v4/kwbimage.cfg
 create mode 100644 board/cloudengines/pogo_v4/pogo_v4.c
board/cloudengines/pogo_v4/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..35fd7858b7
@@ -0,0 +1,6 @@
+POGO_V4 BOARD
+M:	Tony Dinh <[email protected]>
+S:	Maintained
+F:	board/cloudengines/pogo_v4/
+F:	include/configs/pogo_v4.h
+F:	configs/pogo_v4_defconfig
board/cloudengines/pogo_v4/Makefile new file +10 -0
new file mode 100644
index 0000000000..511bf5ff7e
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2014-2021 Tony Dinh <[email protected]>
+#
+# Based on
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+
+obj-y	:= pogo_v4.o
board/cloudengines/pogo_v4/kwbimage.cfg new file +148 -0

148 lines not on this page · raw message

board/cloudengines/pogo_v4/pogo_v4.c new file +220 -0

220 lines not on this page · raw message

Signature · 1 line
2.30.2
#4 lore raw

Re: [PATCH v4 3/4] arm: kirkwood: Pogoplug-V4 : Add board implementation files

Quoted 39 lines · On Thursday 20 January 2022 17:50:54 Tony Dinh wrote:
board/cloudengines/pogo_v4/pogo_v4.c new file +34 -0
new file mode 100644
index 0000000000..c85de0b22e
+int fdt_get_phy_addr(const char *path)
+{
+	const void *fdt = gd->fdt_blob;
+	const u32 *reg;
+	const u32 *val;
+	int node, phandle, addr;
+
+	/* Find the node by its full path */
+	node = fdt_path_offset(fdt, path);
+	if (node >= 0) {
+		/* Look up phy-handle */
+		val = fdt_getprop(fdt, node, "phy-handle", NULL);
+		if (!val) {
+			/* Look up phy (deprecated property for phy handle) */
+			val = fdt_getprop(fdt, node, "phy", NULL);
+		}
+		if (val) {
+			phandle = fdt32_to_cpu(*val);
+			if (!phandle)
+				return -FDT_ERR_NOTFOUND;
+
+			/* Follow it to its node */
+			node = fdt_node_offset_by_phandle(fdt, phandle);
+			if (node) {
+				/* Look up reg */
+				reg = fdt_getprop(fdt, node, "reg", NULL);
+				if (reg) {
+					addr = fdt32_to_cpu(*reg);
+					return addr;
+				}
+			}
+		}
+	}
+	return -FDT_ERR_NOTFOUND;

board/cloudengines/pogo_v4/pogo_v4.c line 160

Quoted 10 lines
board/cloudengines/pogo_v4/pogo_v4.c new file +10 -0
+}
+
+#if defined(CONFIG_RESET_PHY_R)
+/* Configure and initialize PHY */
+void reset_phy(void)
+{
+	u16 reg;
+	int phyaddr;
+	char *name = "ethernet-controller@72000";
+	char *eth0_path = "/ocp@f1000000/ethernet-controller@72000";

Hello! I would suggest to avoid hardcoding DT node names and DT node paths into source code.

How to avoid it?

In DTS file define alias "ethernet0" as alias to eth0 node:

	aliases {
		ethernet0 = &eth0;
	};

(just before memory {} node)

&eth0 label is already defined in arch/arm/dts/kirkwood.dtsi.

Function fdt_path_offset() understands either full path or alias. So you can call fdt_get_phy_addr("ethernet0").

And to get node name you can use function fdt_get_name() which takes node offset - return value of fdt_path_offset().

And maybe... to avoid calling fdt_path_offset() two times, you may adjust fdt_get_phy_addr() to directly take node offset (not path/alias).

So something like this:

    node = fdt_path_offset(gd->fdt_blob, "ethernet0");
    ... error checking ...
    name = fdt_get_name(gd->fdt_blob, node, NULL);
    ... error checking ...
    miiphy_set_current_dev(name);
    ... error checking ...
    fdt_get_phy_addr(node);
    ... error checking ...
Quoted 22 lines
board/cloudengines/pogo_v4/pogo_v4.c new file +22 -0
+	if (miiphy_set_current_dev(name))
+		return;
+
+	phyaddr = fdt_get_phy_addr(eth0_path);
+	if (phyaddr < 0)
+		return;
+
+	/*
+	 * Enable RGMII delay on Tx and Rx for CPU port
+	 * Ref: sec 4.7.2 of chip datasheet
+	 */
+	miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
+	miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, &reg);
+	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+	miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
+	miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);
+
+	/* reset the phy */
+	miiphy_reset(name, phyaddr);
+
+	printf("88E1116 Initialized on %s\n", name);
+}
author
#5 lore raw

Re: [PATCH v4 3/4] arm: kirkwood: Pogoplug-V4 : Add board implementation files

Hi Pali and Stefan,

Quoted 67 lines · Pali Rohár
Quoted 39 lines · On Thursday 20 January 2022 17:50:54 Tony Dinh wrote:
board/cloudengines/pogo_v4/pogo_v4.c new file +34 -0
new file mode 100644
index 0000000000..c85de0b22e
+int fdt_get_phy_addr(const char *path)
+{
+     const void *fdt = gd->fdt_blob;
+     const u32 *reg;
+     const u32 *val;
+     int node, phandle, addr;
+
+     /* Find the node by its full path */
+     node = fdt_path_offset(fdt, path);
+     if (node >= 0) {
+             /* Look up phy-handle */
+             val = fdt_getprop(fdt, node, "phy-handle", NULL);
+             if (!val) {
+                     /* Look up phy (deprecated property for phy handle) */
+                     val = fdt_getprop(fdt, node, "phy", NULL);
+             }
+             if (val) {
+                     phandle = fdt32_to_cpu(*val);
+                     if (!phandle)
+                             return -FDT_ERR_NOTFOUND;
+
+                     /* Follow it to its node */
+                     node = fdt_node_offset_by_phandle(fdt, phandle);
+                     if (node) {
+                             /* Look up reg */
+                             reg = fdt_getprop(fdt, node, "reg", NULL);
+                             if (reg) {
+                                     addr = fdt32_to_cpu(*reg);
+                                     return addr;
+                             }
+                     }
+             }
+     }
+     return -FDT_ERR_NOTFOUND;

board/cloudengines/pogo_v4/pogo_v4.c line 160

Quoted 10 lines
board/cloudengines/pogo_v4/pogo_v4.c new file +10 -0
+}
+
+#if defined(CONFIG_RESET_PHY_R)
+/* Configure and initialize PHY */
+void reset_phy(void)
+{
+     u16 reg;
+     int phyaddr;
+     char *name = "ethernet-controller@72000";
+     char *eth0_path = "/ocp@f1000000/ethernet-controller@72000";

Hello! I would suggest to avoid hardcoding DT node names and DT node paths into source code.

How to avoid it?

In DTS file define alias "ethernet0" as alias to eth0 node:

        aliases {
                ethernet0 = &eth0;
        };

(just before memory {} node)

&eth0 label is already defined in arch/arm/dts/kirkwood.dtsi.

Quoted 8 lines

Function fdt_path_offset() understands either full path or alias. So you can call fdt_get_phy_addr("ethernet0").

And to get node name you can use function fdt_get_name() which takes node offset - return value of fdt_path_offset().

And maybe... to avoid calling fdt_path_offset() two times, you may adjust fdt_get_phy_addr() to directly take node offset (not path/alias).

Pali,
Thanks for your suggestion and reviewing this fdt_get_phy_addr() function. However, this function will be removed. See my followup post in the V3 patch thread about the uclass MVGBE.

https://lists.denx.de/pipermail/u-boot/2022-January/472691.html

Stefan,
Perhaps I should send in a v5 patch series for this board now (instead of reworking this file in a separate patch)? I've tested the uclass MVGBE in this board and it is working as I expected.

Thank,
Tony

Quoted 35 lines

So something like this:

    node = fdt_path_offset(gd->fdt_blob, "ethernet0");
    ... error checking ...
    name = fdt_get_name(gd->fdt_blob, node, NULL);
    ... error checking ...
    miiphy_set_current_dev(name);
    ... error checking ...
    fdt_get_phy_addr(node);
    ... error checking ...
Quoted 22 lines
board/cloudengines/pogo_v4/pogo_v4.c new file +22 -0
+     if (miiphy_set_current_dev(name))
+             return;
+
+     phyaddr = fdt_get_phy_addr(eth0_path);
+     if (phyaddr < 0)
+             return;
+
+     /*
+      * Enable RGMII delay on Tx and Rx for CPU port
+      * Ref: sec 4.7.2 of chip datasheet
+      */
+     miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
+     miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, &reg);
+     reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+     miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
+     miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);
+
+     /* reset the phy */
+     miiphy_reset(name, phyaddr);
+
+     printf("88E1116 Initialized on %s\n", name);
+}
author
#6 lore raw

Re: [PATCH v4 3/4] arm: kirkwood: Pogoplug-V4 : Add board implementation files

Hi Pali,

Quoted 85 lines · Tony Dinh

Hi Pali and Stefan,

Quoted 67 lines · Pali Rohár
Quoted 39 lines · On Thursday 20 January 2022 17:50:54 Tony Dinh wrote:
board/cloudengines/pogo_v4/pogo_v4.c new file +34 -0
new file mode 100644
index 0000000000..c85de0b22e
+int fdt_get_phy_addr(const char *path)
+{
+     const void *fdt = gd->fdt_blob;
+     const u32 *reg;
+     const u32 *val;
+     int node, phandle, addr;
+
+     /* Find the node by its full path */
+     node = fdt_path_offset(fdt, path);
+     if (node >= 0) {
+             /* Look up phy-handle */
+             val = fdt_getprop(fdt, node, "phy-handle", NULL);
+             if (!val) {
+                     /* Look up phy (deprecated property for phy handle) */
+                     val = fdt_getprop(fdt, node, "phy", NULL);
+             }
+             if (val) {
+                     phandle = fdt32_to_cpu(*val);
+                     if (!phandle)
+                             return -FDT_ERR_NOTFOUND;
+
+                     /* Follow it to its node */
+                     node = fdt_node_offset_by_phandle(fdt, phandle);
+                     if (node) {
+                             /* Look up reg */
+                             reg = fdt_getprop(fdt, node, "reg", NULL);
+                             if (reg) {
+                                     addr = fdt32_to_cpu(*reg);
+                                     return addr;
+                             }
+                     }
+             }
+     }
+     return -FDT_ERR_NOTFOUND;

board/cloudengines/pogo_v4/pogo_v4.c line 160

Quoted 10 lines
board/cloudengines/pogo_v4/pogo_v4.c new file +10 -0
+}
+
+#if defined(CONFIG_RESET_PHY_R)
+/* Configure and initialize PHY */
+void reset_phy(void)
+{
+     u16 reg;
+     int phyaddr;
+     char *name = "ethernet-controller@72000";
+     char *eth0_path = "/ocp@f1000000/ethernet-controller@72000";

Hello! I would suggest to avoid hardcoding DT node names and DT node paths into source code.

How to avoid it?

In DTS file define alias "ethernet0" as alias to eth0 node:

        aliases {
                ethernet0 = &eth0;
        };

(just before memory {} node)

&eth0 label is already defined in arch/arm/dts/kirkwood.dtsi.

Quoted 8 lines

Function fdt_path_offset() understands either full path or alias. So you can call fdt_get_phy_addr("ethernet0").

And to get node name you can use function fdt_get_name() which takes node offset - return value of fdt_path_offset().

And maybe... to avoid calling fdt_path_offset() two times, you may adjust fdt_get_phy_addr() to directly take node offset (not path/alias).

Pali,
Thanks for your suggestion and reviewing this fdt_get_phy_addr() function. However, this function will be removed. See my followup post in the V3 patch thread about the uclass MVGBE.

Quoted 7 lines

https://lists.denx.de/pipermail/u-boot/2022-January/472691.html

Stefan,
Perhaps I should send in a v5 patch series for this board now (instead of reworking this file in a separate patch)? I've tested the uclass MVGBE in this board and it is working as I expected.

Here is the test using mvgbe uclass. I've added some debug printfs to see what the calling sequence is.

<BEGIN log>
U-Boot 2022.01-00673-g70fe7827f2-dirty (Jan 22 2022 - 00:09:05 -0800) Pogoplug V4

SoC:   Kirkwood 88F6281_A1
Model: Cloud Engines PogoPlug Series 4
DRAM:  128 MiB
Core:  11 devices, 10 uclasses, devicetree: separate
NAND:  128 MiB
MMC:   mvsdio@90000: 0
Loading Environment from NAND... OK
In:    serial
Out:   serial
Err:   serial
pcie0.0: Link up
Net:   mvgbe_of_to_plat

mvgbe_of_to_plat phy-mode 1
mvgbe_probe
eth0: ethernet-controller@72000
Hit any key to stop autoboot: 0

Pogo_V4> ping 192.168.0.1
mvgbe_start UCLASS_ETH mvgbe
mvgbe_start PHY addr 0
__mvgbe_phy_init phy_interface = gmii
phy_config
phy.c board_phy_config
phy.c board_phy_config calling default phydev->drv->config phy.c genphy_config
ethernet-controller@72000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-controller@72000 device
host 192.168.0.1 is alive
<END log>

So the network bringup is purely based on the DTS. None of the marvell.c driver config is involved (i.e genphy_config function is where the configuration occurs). It is currently working fine with gmii phy-mode. So to get rgmii, we'll just need to add a phy-mode = "rgmii" property to the eth0 node in the DTS.

All this to say is I'm happy that I can remove a lot of code in pogo_v4.c, and not have to patch anything in the common area like FDT or network PHY.

Thanks,
Tony

Quoted 39 lines

Thank,
Tony

Quoted 35 lines

So something like this:

    node = fdt_path_offset(gd->fdt_blob, "ethernet0");
    ... error checking ...
    name = fdt_get_name(gd->fdt_blob, node, NULL);
    ... error checking ...
    miiphy_set_current_dev(name);
    ... error checking ...
    fdt_get_phy_addr(node);
    ... error checking ...
Quoted 22 lines
board/cloudengines/pogo_v4/pogo_v4.c new file +22 -0
+     if (miiphy_set_current_dev(name))
+             return;
+
+     phyaddr = fdt_get_phy_addr(eth0_path);
+     if (phyaddr < 0)
+             return;
+
+     /*
+      * Enable RGMII delay on Tx and Rx for CPU port
+      * Ref: sec 4.7.2 of chip datasheet
+      */
+     miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
+     miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, &reg);
+     reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+     miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
+     miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);
+
+     /* reset the phy */
+     miiphy_reset(name, phyaddr);
+
+     printf("88E1116 Initialized on %s\n", name);
+}
author
#7 lore raw

PATCH v4 4/4 arm: kirkwood: Pogoplug V4 : Add board include header and defconfig files

In reply to Tony Dinh

Add board include header and defconfig files for Pogoplug V4

---

Changes in v4:
- Remove CONFIG_FEATURE_COMMAND_EDITING and ifdefs for CMD_NET in include header

Changes in v3:
- Migrate config symbols from board include header to defconfig
- Remove obsolete config symbols from header file
- Don't use ifdefs for unselectable config symbols in header file

Changes in v2:
- Use canonical format for defconfig file

 configs/pogo_v4_defconfig | 79 +++++++++++++++++++++++++++++++++++++++
 include/configs/pogo_v4.h | 53 ++++++++++++++++++++++++++
 2 files changed, 132 insertions(+)
 create mode 100644 configs/pogo_v4_defconfig
 create mode 100644 include/configs/pogo_v4.h
configs/pogo_v4_defconfig new file +79 -0
new file mode 100644
index 0000000000..5490067b9e
@@ -0,0 +1,79 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_SYS_DCACHE_OFF=y
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_SYS_THUMB_BUILD=y
+CONFIG_ARCH_KIRKWOOD=y
+CONFIG_SYS_KWD_CONFIG="board/cloudengines/pogo_v4/kwbimage.cfg"
+CONFIG_SYS_TEXT_BASE=0x600000
+CONFIG_TARGET_POGO_V4=y
+CONFIG_ENV_SIZE=0x20000
+CONFIG_ENV_OFFSET=0xC0000
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogoplug-series-4"
+CONFIG_IDENT_STRING="\nPogoplug V4"
+CONFIG_SYS_LOAD_ADDR=0x800000
+CONFIG_BOOTSTAGE=y
+CONFIG_SHOW_BOOT_PROGRESS=y
+CONFIG_BOOTDELAY=10
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="setenv bootargs ${bootargs_console}; run bootcmd_usb; bootm 0x00800000 0x01100000 0x2c00000"
+CONFIG_USE_PREBOOT=y
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="Pogo_V4> "
+CONFIG_CMD_BOOTZ=y
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SATA=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SNTP=y
+CONFIG_CMD_DNS=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_JFFS2=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)"
+CONFIG_CMD_UBI=y
+CONFIG_ISO_PARTITION=y
+CONFIG_EFI_PARTITION=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_NAND=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETCONSOLE=y
+CONFIG_DM=y
+CONFIG_SATA_MV=y
+CONFIG_KIRKWOOD_GPIO=y
+# CONFIG_MMC_HW_PARTITIONING is not set
+CONFIG_MVEBU_MMC=y
+CONFIG_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_DM_ETH=y
+CONFIG_MVGBE=y
+CONFIG_MII=y
+CONFIG_PCI=y
+CONFIG_PCI_MVEBU=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_EMULATION=y
+CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_PCI=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_NAND=y
include/configs/pogo_v4.h new file +53 -0

53 lines not on this page · raw message

Signature · 1 line
2.30.2