Skip to contentSkip to conversation

enable usb support on rk356x

PATCH Superseded Peter Geis 3 participants 18 messages Feb 27, 2022 – Mar 1, 2022

Subsystems (4)

v3 of 5 Superseded Latest is v5 →

lore
Share & tools
lore

Peter Geis

author
#0 lore raw

v3 cover enable usb support on rk356x

Good Morning,

This is my patch series that I have maintained out of tree until the combophy driver landed.

Patch 1 fixes the grf dt binding from the combophy merge. Patch 2 adds the dt bindings for the grf changes necessary. Patch 3 adds support to the grf driver to set the rk3566 otg clock source.
Patch 4 is a downstream patch ported forward to shut down the usb3 clock when the controller is operating in usb2 mode.
Patch 5 adds the dwc3 nodes to the rk356x device tree includes. Patch 6 enables the dwc3 nodes on the Quartz64 Model A. Patch 7 enables the dwc3 nodes on the rk3568-evb.

Note, there are functional changes from previous versions.

Please review and apply.

Very Respectfully,
Peter Geis

Changelog:
v3:
- Drop the dwc-of-simple method in favor of using dwc core.
- Drop all quirks except snps,dis_u2_susphy_quirk, which is necessary to prevent device detection failures in some states.
- Drop the reset-names.

v2:
- Add a dt-bindings fix for grf.yaml
- Unify the reset names.
- Constrain the force usb2 clock dwc3 patch to only supported variants of the ip.
- Change dwc3-of-simple to support of-match-data.
- Drop the PCLK-PIPE clk.
- Rename the usb nodes to be more friendly.
- Add the rk3568-evb enable patch.

Bin Yang (1):
usb: dwc3: core: do not use 3.0 clock when operating in 2.0 mode

Michael Riesch (1):
arm64: dts: rockchip: add usb3 support to rk3568-evb1-v10

Peter Geis (5):
dt-bindings: soc: grf: fix rk3568 usb definitions
dt-bindings: soc: grf: add rk3566-pipe-grf compatible
soc: rockchip: set dwc3 clock for rk3566
arm64: dts: rockchip: add rk356x dwc3 usb3 nodes
arm64: dts: rockchip: enable dwc3 on quartz64-a

 .../devicetree/bindings/soc/rockchip/grf.yaml |  5 +-
 .../boot/dts/rockchip/rk3566-quartz64-a.dts   | 37 +++++++++++++++
 arch/arm64/boot/dts/rockchip/rk3566.dtsi      | 11 +++++
 .../boot/dts/rockchip/rk3568-evb1-v10.dts     | 46 +++++++++++++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi      |  9 ++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi      | 35 +++++++++++++-
 drivers/soc/rockchip/grf.c                    | 17 +++++++
 drivers/usb/dwc3/core.c                       |  5 ++
 drivers/usb/dwc3/core.h                       |  1 +
 9 files changed, 163 insertions(+), 3 deletions(-)
Signature · 1 line
2.25.1
author
#1 lore raw

PATCH v3 1/7 dt-bindings: soc: grf: fix rk3568 usb definitions

The rockchip,rk3568-pipe-grf and rockchip,rk3568-pipe-phy-grf compatibles were incorrectly assigned to the syscon, simple-mfd enumeration, vice only the syscon enumeration.
This leads a dtbs_check failure.

Move these to the syscon enumeration.

Fixes b3df807e1fb0 ("dt-bindings: soc: grf: add naneng combo phy register compatible")
---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/soc/rockchip/grf.yaml +2 -2
index 072318fcd57b..5079e9d24af6 100644
@@ -15,6 +15,8 @@ properties:
       - items:
           - enum:
               - rockchip,rk3288-sgrf
+              - rockchip,rk3568-pipe-grf
+              - rockchip,rk3568-pipe-phy-grf
               - rockchip,rk3568-usb2phy-grf
               - rockchip,rv1108-usbgrf
           - const: syscon
@@ -39,8 +41,6 @@ properties:
               - rockchip,rk3399-grf
               - rockchip,rk3399-pmugrf
               - rockchip,rk3568-grf
-              - rockchip,rk3568-pipe-grf
-              - rockchip,rk3568-pipe-phy-grf
               - rockchip,rk3568-pmugrf
               - rockchip,rv1108-grf
               - rockchip,rv1108-pmugrf
Signature · 1 line
2.25.1
author
#2 lore raw

PATCH v3 2/7 dt-bindings: soc: grf: add rk3566-pipe-grf compatible

In reply to Peter Geis

The rk3566 requires special handling for the dwc3-otg clock in order for the port to function correctly.
Add a binding for the rk3566-pipe-grf so we can handle setup with the grf driver.

---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/soc/rockchip/grf.yaml +1 -0
index 5079e9d24af6..75a2b8bb25fb 100644
@@ -15,6 +15,7 @@ properties:
       - items:
           - enum:
               - rockchip,rk3288-sgrf
+              - rockchip,rk3566-pipe-grf
               - rockchip,rk3568-pipe-grf
               - rockchip,rk3568-pipe-phy-grf
               - rockchip,rk3568-usb2phy-grf
Signature · 1 line
2.25.1
author
#4 lore raw

PATCH v3 4/7 usb: dwc3: core: do not use 3.0 clock when operating in 2.0 mode

In reply to Peter Geis

From: Bin Yang <[email protected]>

In the 3.0 device core, if the core is programmed to operate in 2.0 only, then setting the GUCTL1.DEV_FORCE_20_CLK_FOR_30_CLK makes the internal 2.0(utmi/ulpi) clock to be routed as the 3.0 (pipe) clock. Enabling this feature allows the pipe3 clock to be not-running when forcibly operating in 2.0 device mode.

---
 drivers/usb/dwc3/core.c | 5 +++++
 drivers/usb/dwc3/core.h | 1 +
 2 files changed, 6 insertions(+)
drivers/usb/dwc3/core.c +5 -0
index 18adddfba3da..416d83a055fe 100644
@@ -1167,6 +1167,11 @@ static int dwc3_core_init(struct dwc3 *dwc)
 		if (dwc->parkmode_disable_ss_quirk)
 			reg |= DWC3_GUCTL1_PARKMODE_DISABLE_SS;
 
+		if (DWC3_VER_IS_WITHIN(DWC3, 290A, ANY) &&
+		    (dwc->maximum_speed == USB_SPEED_HIGH ||
+		     dwc->maximum_speed == USB_SPEED_FULL))
+			reg |= DWC3_GUCTL1_DEV_FORCE_20_CLK_FOR_30_CLK;
+
 		dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
 	}
 
drivers/usb/dwc3/core.h +1 -0
index eb9c1efced05..ea3ca04406bb 100644
@@ -259,6 +259,7 @@
 /* Global User Control 1 Register */
 #define DWC3_GUCTL1_DEV_DECOUPLE_L1L2_EVT	BIT(31)
 #define DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS	BIT(28)
+#define DWC3_GUCTL1_DEV_FORCE_20_CLK_FOR_30_CLK	BIT(26)
 #define DWC3_GUCTL1_DEV_L1_EXIT_BY_HW		BIT(24)
 #define DWC3_GUCTL1_PARKMODE_DISABLE_SS		BIT(17)
 
Signature · 1 line
2.25.1
author
#3 lore raw

PATCH v3 3/7 soc: rockchip: set dwc3 clock for rk3566

In reply to Peter Geis

The rk3566 dwc3 otg port clock is unavailable at boot, as it defaults to the combophy as the clock source. As combophy0 doesn't exist on rk3566, we need to set the clock source to the usb2 phy instead.

Add handling to the grf driver to handle this on boot.

---
 drivers/soc/rockchip/grf.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
drivers/soc/rockchip/grf.c +17 -0
index 494cf2b5bf7b..384461b70684 100644
@@ -108,6 +108,20 @@ static const struct rockchip_grf_info rk3399_grf __initconst = {
 	.num_values = ARRAY_SIZE(rk3399_defaults),
 };
 
+#define RK3566_GRF_USB3OTG0_CON1	0x0104
+
+static const struct rockchip_grf_value rk3566_defaults[] __initconst = {
+	{ "usb3otg port switch", RK3566_GRF_USB3OTG0_CON1, HIWORD_UPDATE(0, 1, 12) },
+	{ "usb3otg clock switch", RK3566_GRF_USB3OTG0_CON1, HIWORD_UPDATE(1, 1, 7) },
+	{ "usb3otg disable usb3", RK3566_GRF_USB3OTG0_CON1, HIWORD_UPDATE(1, 1, 0) },
+};
+
+static const struct rockchip_grf_info rk3566_pipegrf __initconst = {
+	.values = rk3566_defaults,
+	.num_values = ARRAY_SIZE(rk3566_defaults),
+};
+
+
 static const struct of_device_id rockchip_grf_dt_match[] __initconst = {
 	{
 		.compatible = "rockchip,rk3036-grf",
@@ -130,6 +144,9 @@ static const struct of_device_id rockchip_grf_dt_match[] __initconst = {
 	}, {
 		.compatible = "rockchip,rk3399-grf",
 		.data = (void *)&rk3399_grf,
+	}, {
+		.compatible = "rockchip,rk3566-pipe-grf",
+		.data = (void *)&rk3566_pipegrf,
 	},
 	{ /* sentinel */ },
 };
Signature · 1 line
2.25.1
author
#5 lore raw

PATCH v3 5/7 arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

In reply to Peter Geis

Add the dwc3 device nodes to the rk356x device trees.
The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable dwc3 host controller.
The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable dwc3 host controller.

---
 arch/arm64/boot/dts/rockchip/rk3566.dtsi | 11 ++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 ++++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 35 +++++++++++++++++++++++-
 3 files changed, 54 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3566.dtsi +11 -0
index 3839eef5e4f7..0b957068ff89 100644
@@ -6,6 +6,10 @@ / {
 	compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -18,3 +22,10 @@ power-domain@RK3568_PD_PIPE {
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>;
+	phy-names = "usb2-phy";
+	extcon = <&usb2phy0>;
+	maximum-speed = "high-speed";
+};
arch/arm64/boot/dts/rockchip/rk3568.dtsi +9 -0
index 5b0f528d6818..8ba9334f9753 100644
@@ -99,6 +99,10 @@ opp-1992000000 {
 	};
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+	phy-names = "usb2-phy", "usb3-phy";
+};
arch/arm64/boot/dts/rockchip/rk356x.dtsi +34 -1
index 7cdef800cb3c..072bb9080cd6 100644
@@ -230,6 +230,40 @@ scmi_shmem: sram@0 {
 		};
 	};
 
+	usb_host0_xhci: usb@fcc00000 {
+		compatible = "snps,dwc3";
+		reg = <0x0 0xfcc00000 0x0 0x400000>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+			 <&cru ACLK_USB3OTG0>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "host";
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG0>;
+		snps,dis_u2_susphy_quirk;
+		status = "disabled";
+	};
+
+	usb_host1_xhci: usb@fd000000 {
+		compatible = "snps,dwc3";
+		reg = <0x0 0xfd000000 0x0 0x400000>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+			 <&cru ACLK_USB3OTG1>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "host";
+		phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+		phy-names = "usb2-phy", "usb3-phy";
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG1>;
+		snps,dis_u2_susphy_quirk;
+		status = "disabled";
+	};
+
 	gic: interrupt-controller@fd400000 {
 		compatible = "arm,gic-v3";
 		reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
@@ -297,7 +331,6 @@ pmu_io_domains: io-domains {
 	};
 
 	pipegrf: syscon@fdc50000 {
-		compatible = "rockchip,rk3568-pipe-grf", "syscon";
 		reg = <0x0 0xfdc50000 0x0 0x1000>;
 	};
 
Signature · 1 line
2.25.1
author
#16 lore raw

PATCH v3 6/7 arm64: dts: rockchip: enable dwc3 on quartz64-a

In reply to Peter Geis

The quartz64 model a has support for both the dwc3 otg port and the dwc3 host port. Add the otg power supply and dwc3 nodes to the device tree to enable support for these.

---
 .../boot/dts/rockchip/rk3566-quartz64-a.dts   | 37 +++++++++++++++++++
 1 file changed, 37 insertions(+)
arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts +37 -0
index dd7f4b9b686b..141a433429b5 100644
@@ -151,6 +151,16 @@ vcc5v0_usb20_host: vcc5v0_usb20_host {
 		vin-supply = <&vcc5v0_usb>;
 	};
 
+	vcc5v0_usb20_otg: vcc5v0_usb20_otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+		regulator-name = "vcc5v0_usb20_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dcdc_boost>;
+	};
+
 	vcc3v3_sd: vcc3v3_sd {
 		compatible = "regulator-fixed";
 		enable-active-low;
@@ -187,6 +197,10 @@ vcc_wl: vcc_wl {
 	};
 };
 
+&combphy1 {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&vdd_cpu>;
 };
@@ -672,6 +686,29 @@ &usb_host1_ohci {
 	status = "okay";
 };
 
+&usb_host0_xhci {
+	status = "okay";
+};
+
+/* usb3 controller is muxed with sata1 */
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb20_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb20_otg>;
+	status = "okay";
+};
+
 &usb2phy1 {
 	status = "okay";
 };
Signature · 1 line
2.25.1
author
#17 lore raw

PATCH v3 7/7 arm64: dts: rockchip: add usb3 support to rk3568-evb1-v10

In reply to Peter Geis

From: Michael Riesch <[email protected]>

The Rockchip RK3568 EVB1 features one USB 3.0 device-only (USB 2.0 OTG) port and one USB 3.0 host-only port. Activate the USB 3.0 controller nodes and phy nodes in the device tree.

---
 .../boot/dts/rockchip/rk3568-evb1-v10.dts     | 46 +++++++++++++++++++
 1 file changed, 46 insertions(+)
arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts +46 -0
index a794a0ea5c70..622be8be9813 100644
@@ -103,6 +103,18 @@ vcc5v0_usb_host: vcc5v0-usb-host {
 		vin-supply = <&vcc5v0_usb>;
 	};
 
+	vcc5v0_usb_otg: vcc5v0-usb-otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
 	vcc3v3_lcd0_n: vcc3v3-lcd0-n {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3_lcd0_n";
@@ -136,6 +148,14 @@ regulator-state-mem {
 	};
 };
 
+&combphy0 {
+	status = "okay";
+};
+
+&combphy1 {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&vdd_cpu>;
 };
@@ -507,6 +527,9 @@ usb {
 		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
 			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
 	};
 };
 
@@ -568,6 +591,11 @@ &usb_host0_ohci {
 	status = "okay";
 };
 
+&usb_host0_xhci {
+	extcon = <&usb2phy0>;
+	status = "okay";
+};
+
 &usb_host1_ehci {
 	status = "okay";
 };
@@ -576,6 +604,24 @@ &usb_host1_ohci {
 	status = "okay";
 };
 
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	vbus-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
 &usb2phy1 {
 	status = "okay";
 };
Signature · 1 line
2.25.1
#6 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

In reply to Peter Geis
Quoted 68 lines · Peter Geis

Add the dwc3 device nodes to the rk356x device trees.
The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable dwc3 host controller.
The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable dwc3 host controller.

---
 arch/arm64/boot/dts/rockchip/rk3566.dtsi | 11 ++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 ++++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 35 +++++++++++++++++++++++-
 3 files changed, 54 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3566.dtsi +11 -0
index 3839eef5e4f7..0b957068ff89 100644
@@ -6,6 +6,10 @@ / {
 	compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -18,3 +22,10 @@ power-domain@RK3568_PD_PIPE {
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>;
+	phy-names = "usb2-phy";
+	extcon = <&usb2phy0>;
+	maximum-speed = "high-speed";
+};
arch/arm64/boot/dts/rockchip/rk3568.dtsi +9 -0
index 5b0f528d6818..8ba9334f9753 100644
@@ -99,6 +99,10 @@ opp-1992000000 {
 	};
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+	phy-names = "usb2-phy", "usb3-phy";
+};
arch/arm64/boot/dts/rockchip/rk356x.dtsi +0 -0
index 7cdef800cb3c..072bb9080cd6 100644

arch/arm64/boot/dts/rockchip/rk356x.dtsi scmi_shmem: sram@0 { · line 235

Quoted 6 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +2 -0
@@ -230,6 +230,40 @@ scmi_shmem: sram@0 {
 		};
 	};
 
+	usb_host0_xhci: usb@fcc00000 {
 
+		compatible = "snps,dwc3";

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

compatible strings must be SoC orientated.
Add binding like you did before.

Quoted 7 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +7 -0
+		reg = <0x0 0xfcc00000 0x0 0x400000>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+			 <&cru ACLK_USB3OTG0>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "host";

arch/arm64/boot/dts/rockchip/rk356x.dtsi scmi_shmem: sram@0 { · line 250

Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +9 -0
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG0>;
+		snps,dis_u2_susphy_quirk;
+		status = "disabled";
+	};
+
+	usb_host1_xhci: usb@fd000000 {
 
+		compatible = "snps,dwc3";

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

Quoted 27 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +16 -0
+		reg = <0x0 0xfd000000 0x0 0x400000>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+			 <&cru ACLK_USB3OTG1>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "host";
+		phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+		phy-names = "usb2-phy", "usb3-phy";
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG1>;
+		snps,dis_u2_susphy_quirk;
+		status = "disabled";
+	};
+
 	gic: interrupt-controller@fd400000 {
arch/arm64/boot/dts/rockchip/rk356x.dtsi +0 -1
 		compatible = "arm,gic-v3";
 		reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
@@ -297,7 +331,6 @@ pmu_io_domains: io-domains {
 	};
 
 	pipegrf: syscon@fdc50000 {
-		compatible = "rockchip,rk3568-pipe-grf", "syscon";
 		reg = <0x0 0xfdc50000 0x0 0x1000>;
 	};
 
author
#7 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

Quoted 75 lines · Johan Jonker
Quoted 71 lines · Peter Geis

Add the dwc3 device nodes to the rk356x device trees.
The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable dwc3 host controller.
The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable dwc3 host controller.

---
 arch/arm64/boot/dts/rockchip/rk3566.dtsi | 11 ++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 ++++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 35 +++++++++++++++++++++++-
 3 files changed, 54 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3566.dtsi +11 -0
index 3839eef5e4f7..0b957068ff89 100644
@@ -6,6 +6,10 @@ / {
      compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -18,3 +22,10 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>;
+     phy-names = "usb2-phy";
+     extcon = <&usb2phy0>;
+     maximum-speed = "high-speed";
+};
arch/arm64/boot/dts/rockchip/rk3568.dtsi +9 -0
index 5b0f528d6818..8ba9334f9753 100644
@@ -99,6 +99,10 @@ opp-1992000000 {
      };
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+     phy-names = "usb2-phy", "usb3-phy";
+};
arch/arm64/boot/dts/rockchip/rk356x.dtsi +0 -0
index 7cdef800cb3c..072bb9080cd6 100644
@@ -230,6 +230,40 @@ scmi_shmem: sram@0 {
              };
      };
 
Quoted 8 lines

arch/arm64/boot/dts/rockchip/rk356x.dtsi scmi_shmem: sram@0 { · line 234

Quoted 3 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +2 -0
+     usb_host0_xhci: usb@fcc00000 {
 
+             compatible = "snps,dwc3";

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

compatible strings must be SoC orientated.
Add binding like you did before.

Okay, should this go in the core yaml, since it's not really handled by of-simple?
Also, should I add in the compatible for rk3328 as well?

Quoted 48 lines
Quoted 8 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +7 -0
+             reg = <0x0 0xfcc00000 0x0 0x400000>;
+             interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+                      <&cru ACLK_USB3OTG0>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";

arch/arm64/boot/dts/rockchip/rk356x.dtsi scmi_shmem: sram@0 { · line 250

Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +9 -0
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG0>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
+     usb_host1_xhci: usb@fd000000 {
 
+             compatible = "snps,dwc3";

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

Quoted 27 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +16 -0
+             reg = <0x0 0xfd000000 0x0 0x400000>;
+             interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+                      <&cru ACLK_USB3OTG1>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";
+             phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+             phy-names = "usb2-phy", "usb3-phy";
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG1>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
      gic: interrupt-controller@fd400000 {
              compatible = "arm,gic-v3";
              reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
arch/arm64/boot/dts/rockchip/rk356x.dtsi +0 -1
@@ -297,7 +331,6 @@ pmu_io_domains: io-domains {
      };
 
      pipegrf: syscon@fdc50000 {
-             compatible = "rockchip,rk3568-pipe-grf", "syscon";
              reg = <0x0 0xfdc50000 0x0 0x1000>;
      };
 
#11 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

In reply to Peter Geis

Hi Peter,

Quoted 29 lines · Peter Geis

Add the dwc3 device nodes to the rk356x device trees.
The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable dwc3 host controller.
The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable dwc3 host controller.

---
 arch/arm64/boot/dts/rockchip/rk3566.dtsi | 11 ++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 ++++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 35 +++++++++++++++++++++++-
 3 files changed, 54 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3566.dtsi +4 -0
index 3839eef5e4f7..0b957068ff89 100644
@@ -6,6 +6,10 @@ / {
 	compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;

arch/arm64/boot/dts/rockchip/rk3566.dtsi power-domain@RK3568_PD_PIPE { · line 29

Quoted 8 lines
arch/arm64/boot/dts/rockchip/rk3566.dtsi +5 -0
@@ -18,3 +22,10 @@ power-domain@RK3568_PD_PIPE {
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>;
+	phy-names = "usb2-phy";
+	extcon = <&usb2phy0>;

I wonder what the correct place for this extcon property is. You defined it on SoC (RK3566) level, in my patch for the RK3568 EVB1 it is added on board level. Is this common to all RK356x variants?

Best regards,
Michael

Quoted 79 lines
arch/arm64/boot/dts/rockchip/rk3566.dtsi +2 -0
+	maximum-speed = "high-speed";
+};
arch/arm64/boot/dts/rockchip/rk3568.dtsi +9 -0
index 5b0f528d6818..8ba9334f9753 100644
@@ -99,6 +99,10 @@ opp-1992000000 {
 	};
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+	phy-names = "usb2-phy", "usb3-phy";
+};
arch/arm64/boot/dts/rockchip/rk356x.dtsi +34 -1
index 7cdef800cb3c..072bb9080cd6 100644
@@ -230,6 +230,40 @@ scmi_shmem: sram@0 {
 		};
 	};
 
+	usb_host0_xhci: usb@fcc00000 {
+		compatible = "snps,dwc3";
+		reg = <0x0 0xfcc00000 0x0 0x400000>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+			 <&cru ACLK_USB3OTG0>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "host";
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG0>;
+		snps,dis_u2_susphy_quirk;
+		status = "disabled";
+	};
+
+	usb_host1_xhci: usb@fd000000 {
+		compatible = "snps,dwc3";
+		reg = <0x0 0xfd000000 0x0 0x400000>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+			 <&cru ACLK_USB3OTG1>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "host";
+		phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+		phy-names = "usb2-phy", "usb3-phy";
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG1>;
+		snps,dis_u2_susphy_quirk;
+		status = "disabled";
+	};
+
 	gic: interrupt-controller@fd400000 {
 		compatible = "arm,gic-v3";
 		reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
@@ -297,7 +331,6 @@ pmu_io_domains: io-domains {
 	};
 
 	pipegrf: syscon@fdc50000 {
-		compatible = "rockchip,rk3568-pipe-grf", "syscon";
 		reg = <0x0 0xfdc50000 0x0 0x1000>;
 	};
 
#8 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

In reply to Peter Geis
Quoted 80 lines · Peter Geis
Quoted 79 lines · Johan Jonker
Quoted 74 lines · Peter Geis

Add the dwc3 device nodes to the rk356x device trees.
The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable dwc3 host controller.
The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable dwc3 host controller.

---
 arch/arm64/boot/dts/rockchip/rk3566.dtsi | 11 ++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 ++++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 35 +++++++++++++++++++++++-
 3 files changed, 54 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3566.dtsi +11 -0
index 3839eef5e4f7..0b957068ff89 100644
@@ -6,6 +6,10 @@ / {
      compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -18,3 +22,10 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>;
+     phy-names = "usb2-phy";
+     extcon = <&usb2phy0>;
+     maximum-speed = "high-speed";
+};
arch/arm64/boot/dts/rockchip/rk3568.dtsi +9 -0
index 5b0f528d6818..8ba9334f9753 100644
@@ -99,6 +99,10 @@ opp-1992000000 {
      };
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+     phy-names = "usb2-phy", "usb3-phy";
+};
arch/arm64/boot/dts/rockchip/rk356x.dtsi +2 -0
index 7cdef800cb3c..072bb9080cd6 100644
@@ -230,6 +230,40 @@ scmi_shmem: sram@0 {
              };
      };
 
+     usb_host0_xhci: usb@fcc00000 {
 
+             compatible = "snps,dwc3";
Quoted 7 lines
Quoted 4 lines

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

compatible strings must be SoC orientated.
Add binding like you did before.

Okay, should this go in the core yaml, since it's not really handled by of-simple?

Nothing to change in core.c, because the fall back string does the trick, so we don't have to change the driver for every new SoC. Change the node compatible here and add the binding. That's it. The rest comes later if needed.

Quoted 1 line

Also, should I add in the compatible for rk3328 as well?

No, same story the fall back string does the trick in core.c

Quoted 49 lines
Quoted 49 lines
Quoted 9 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +7 -0
+             reg = <0x0 0xfcc00000 0x0 0x400000>;
+             interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+                      <&cru ACLK_USB3OTG0>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";

arch/arm64/boot/dts/rockchip/rk356x.dtsi scmi_shmem: sram@0 { · line 250

Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +9 -0
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG0>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
+     usb_host1_xhci: usb@fd000000 {
 
+             compatible = "snps,dwc3";

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

Quoted 27 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +16 -0
+             reg = <0x0 0xfd000000 0x0 0x400000>;
+             interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+                      <&cru ACLK_USB3OTG1>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";
+             phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+             phy-names = "usb2-phy", "usb3-phy";
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG1>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
      gic: interrupt-controller@fd400000 {
              compatible = "arm,gic-v3";
              reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
arch/arm64/boot/dts/rockchip/rk356x.dtsi +0 -1
@@ -297,7 +331,6 @@ pmu_io_domains: io-domains {
      };
 
      pipegrf: syscon@fdc50000 {
-             compatible = "rockchip,rk3568-pipe-grf", "syscon";
              reg = <0x0 0xfdc50000 0x0 0x1000>;
      };
 
author
#12 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

In reply to Michael Riesch
Quoted 37 lines · Michael Riesch

Hi Peter,

Quoted 33 lines · Peter Geis

Add the dwc3 device nodes to the rk356x device trees.
The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable dwc3 host controller.
The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable dwc3 host controller.

---
 arch/arm64/boot/dts/rockchip/rk3566.dtsi | 11 ++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 ++++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 35 +++++++++++++++++++++++-
 3 files changed, 54 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3566.dtsi +5 -0
index 3839eef5e4f7..0b957068ff89 100644
@@ -6,6 +6,10 @@ / {
      compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -18,3 +22,10 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
Quoted 8 lines

arch/arm64/boot/dts/rockchip/rk3566.dtsi power-domain@RK3568_PD_PIPE { · line 29

Quoted 4 lines
arch/arm64/boot/dts/rockchip/rk3566.dtsi +4 -0
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>;
+     phy-names = "usb2-phy";
+     extcon = <&usb2phy0>;

I wonder what the correct place for this extcon property is. You defined it on SoC (RK3566) level, in my patch for the RK3568 EVB1 it is added on board level. Is this common to all RK356x variants?

Yes, the usb2phy is always available as an extcon unless you make a device that doesn't have usb2 capability.
In that case you'd have to override the device anyways. If we want to turn on default role otg here, we'd need this defined here as well or things break.

Quoted 83 lines

Best regards,
Michael

Quoted 79 lines
arch/arm64/boot/dts/rockchip/rk3566.dtsi +2 -0
+     maximum-speed = "high-speed";
+};
arch/arm64/boot/dts/rockchip/rk3568.dtsi +9 -0
index 5b0f528d6818..8ba9334f9753 100644
@@ -99,6 +99,10 @@ opp-1992000000 {
      };
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+     phy-names = "usb2-phy", "usb3-phy";
+};
arch/arm64/boot/dts/rockchip/rk356x.dtsi +34 -1
index 7cdef800cb3c..072bb9080cd6 100644
@@ -230,6 +230,40 @@ scmi_shmem: sram@0 {
              };
      };
 
+     usb_host0_xhci: usb@fcc00000 {
+             compatible = "snps,dwc3";
+             reg = <0x0 0xfcc00000 0x0 0x400000>;
+             interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+                      <&cru ACLK_USB3OTG0>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG0>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
+     usb_host1_xhci: usb@fd000000 {
+             compatible = "snps,dwc3";
+             reg = <0x0 0xfd000000 0x0 0x400000>;
+             interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+                      <&cru ACLK_USB3OTG1>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";
+             phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+             phy-names = "usb2-phy", "usb3-phy";
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG1>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
      gic: interrupt-controller@fd400000 {
              compatible = "arm,gic-v3";
              reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
@@ -297,7 +331,6 @@ pmu_io_domains: io-domains {
      };
 
      pipegrf: syscon@fdc50000 {
-             compatible = "rockchip,rk3568-pipe-grf", "syscon";
              reg = <0x0 0xfdc50000 0x0 0x1000>;
      };
 
author
#9 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

In reply to Johan Jonker
Quoted 89 lines · Johan Jonker
Quoted 85 lines · Peter Geis
Quoted 83 lines · Johan Jonker
Quoted 68 lines · Peter Geis

Add the dwc3 device nodes to the rk356x device trees.
The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable dwc3 host controller.
The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable dwc3 host controller.

---
 arch/arm64/boot/dts/rockchip/rk3566.dtsi | 11 ++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 ++++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 35 +++++++++++++++++++++++-
 3 files changed, 54 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3566.dtsi +11 -0
index 3839eef5e4f7..0b957068ff89 100644
@@ -6,6 +6,10 @@ / {
      compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -18,3 +22,10 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>;
+     phy-names = "usb2-phy";
+     extcon = <&usb2phy0>;
+     maximum-speed = "high-speed";
+};
arch/arm64/boot/dts/rockchip/rk3568.dtsi +9 -0
index 5b0f528d6818..8ba9334f9753 100644
@@ -99,6 +99,10 @@ opp-1992000000 {
      };
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+     phy-names = "usb2-phy", "usb3-phy";
+};
arch/arm64/boot/dts/rockchip/rk356x.dtsi +0 -0
index 7cdef800cb3c..072bb9080cd6 100644

arch/arm64/boot/dts/rockchip/rk356x.dtsi scmi_shmem: sram@0 { · line 235

Quoted 6 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +2 -0
@@ -230,6 +230,40 @@ scmi_shmem: sram@0 {
              };
      };
 
+     usb_host0_xhci: usb@fcc00000 {
 
+             compatible = "snps,dwc3";

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

compatible strings must be SoC orientated.
Add binding like you did before.

Quoted 7 lines
Quoted 2 lines

Okay, should this go in the core yaml, since it's not really handled by of-simple?

Nothing to change in core.c, because the fall back string does the trick, so we don't have to change the driver for every new SoC. Change the node compatible here and add the binding. That's it. The rest comes later if needed.

It's the binding I'm referring to here.
snps,dwc3.yaml seems the logical place, but I want to make sure you concur first.

Quoted 4 lines
Quoted 2 lines

Also, should I add in the compatible for rk3328 as well?

No, same story the fall back string does the trick in core.c

Same thing here, since I'm in snps,dwc3.yaml anyways I can add the rk3328 binding in and silence that error in one go.

Quoted 51 lines
Quoted 51 lines
Quoted 51 lines
Quoted 11 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +7 -0
+             reg = <0x0 0xfcc00000 0x0 0x400000>;
+             interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+                      <&cru ACLK_USB3OTG0>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";

arch/arm64/boot/dts/rockchip/rk356x.dtsi scmi_shmem: sram@0 { · line 250

Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +9 -0
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG0>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
+     usb_host1_xhci: usb@fd000000 {
 
+             compatible = "snps,dwc3";

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

Quoted 27 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +16 -0
+             reg = <0x0 0xfd000000 0x0 0x400000>;
+             interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+                      <&cru ACLK_USB3OTG1>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";
+             phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+             phy-names = "usb2-phy", "usb3-phy";
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG1>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
      gic: interrupt-controller@fd400000 {
              compatible = "arm,gic-v3";
              reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
arch/arm64/boot/dts/rockchip/rk356x.dtsi +0 -1
@@ -297,7 +331,6 @@ pmu_io_domains: io-domains {
      };
 
      pipegrf: syscon@fdc50000 {
-             compatible = "rockchip,rk3568-pipe-grf", "syscon";
              reg = <0x0 0xfdc50000 0x0 0x1000>;
      };
 
#10 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

Quoted 93 lines · Peter Geis
Quoted 92 lines · Johan Jonker
Quoted 87 lines · Peter Geis
Quoted 75 lines · Johan Jonker
Quoted 71 lines · Peter Geis

Add the dwc3 device nodes to the rk356x device trees.
The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable dwc3 host controller.
The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable dwc3 host controller.

---
 arch/arm64/boot/dts/rockchip/rk3566.dtsi | 11 ++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 ++++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 35 +++++++++++++++++++++++-
 3 files changed, 54 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3566.dtsi +11 -0
index 3839eef5e4f7..0b957068ff89 100644
@@ -6,6 +6,10 @@ / {
      compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -18,3 +22,10 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>;
+     phy-names = "usb2-phy";
+     extcon = <&usb2phy0>;
+     maximum-speed = "high-speed";
+};
arch/arm64/boot/dts/rockchip/rk3568.dtsi +9 -0
index 5b0f528d6818..8ba9334f9753 100644
@@ -99,6 +99,10 @@ opp-1992000000 {
      };
 };
 
+&pipegrf {
+     compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
      power-domain@RK3568_PD_PIPE {
              reg = <RK3568_PD_PIPE>;
@@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
              #power-domain-cells = <0>;
      };
 };
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+     phy-names = "usb2-phy", "usb3-phy";
+};
arch/arm64/boot/dts/rockchip/rk356x.dtsi +0 -0
index 7cdef800cb3c..072bb9080cd6 100644
@@ -230,6 +230,40 @@ scmi_shmem: sram@0 {
              };
      };
 
Quoted 8 lines

arch/arm64/boot/dts/rockchip/rk356x.dtsi scmi_shmem: sram@0 { · line 234

Quoted 3 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +2 -0
+     usb_host0_xhci: usb@fcc00000 {
 
+             compatible = "snps,dwc3";

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

compatible strings must be SoC orientated.
Add binding like you did before.

Okay, should this go in the core yaml, since it's not really handled by of-simple?

Quoted 8 lines
Quoted 4 lines

Nothing to change in core.c, because the fall back string does the trick, so we don't have to change the driver for every new SoC. Change the node compatible here and add the binding. That's it. The rest comes later if needed.

It's the binding I'm referring to here.
snps,dwc3.yaml seems the logical place, but I want to make sure you concur first.

rockchip,dwc3.yaml is the place be!
Hurry up!

Use Michael's patch, because his commit message is better.(no reference to rk3399)

https://lore.kernel.org/linux-rockchip/[email protected]/

vs.

https://lore.kernel.org/linux-rockchip/[email protected]/

Quoted 8 lines
Quoted 5 lines
Quoted 3 lines

Also, should I add in the compatible for rk3328 as well?

No, same story the fall back string does the trick in core.c

Same thing here, since I'm in snps,dwc3.yaml anyways I can add the rk3328 binding in and silence that error in one go.

It's been done already:

[PATCH v5 6/8] dt-bindings: usb: dwc3: add description for rk3328

https://lore.kernel.org/linux-rockchip/[email protected]/

Quoted 52 lines
Quoted 52 lines
Quoted 52 lines
Quoted 52 lines
Quoted 12 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +7 -0
+             reg = <0x0 0xfcc00000 0x0 0x400000>;
+             interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+                      <&cru ACLK_USB3OTG0>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";

arch/arm64/boot/dts/rockchip/rk356x.dtsi scmi_shmem: sram@0 { · line 250

Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +9 -0
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG0>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
+     usb_host1_xhci: usb@fd000000 {
 
+             compatible = "snps,dwc3";

compatible = "rockchip,rk3568-dwc3", "snps,dwc3";

Quoted 27 lines
arch/arm64/boot/dts/rockchip/rk356x.dtsi +16 -0
+             reg = <0x0 0xfd000000 0x0 0x400000>;
+             interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+             clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+                      <&cru ACLK_USB3OTG1>;
+             clock-names = "ref_clk", "suspend_clk",
+                           "bus_clk";
+             dr_mode = "host";
+             phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+             phy-names = "usb2-phy", "usb3-phy";
+             phy_type = "utmi_wide";
+             power-domains = <&power RK3568_PD_PIPE>;
+             resets = <&cru SRST_USB3OTG1>;
+             snps,dis_u2_susphy_quirk;
+             status = "disabled";
+     };
+
      gic: interrupt-controller@fd400000 {
              compatible = "arm,gic-v3";
              reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
arch/arm64/boot/dts/rockchip/rk356x.dtsi +0 -1
@@ -297,7 +331,6 @@ pmu_io_domains: io-domains {
      };
 
      pipegrf: syscon@fdc50000 {
-             compatible = "rockchip,rk3568-pipe-grf", "syscon";
              reg = <0x0 0xfdc50000 0x0 0x1000>;
      };
 
#13 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

In reply to Peter Geis

Hi Peter,

Quoted 11 lines · Peter Geis

[...]

Quoted 9 lines

arch/arm64/boot/dts/rockchip/rk3566.dtsi power-domain@RK3568_PD_PIPE { · line 29

Quoted 5 lines
arch/arm64/boot/dts/rockchip/rk3566.dtsi +5 -0
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>;
+     phy-names = "usb2-phy";
+     extcon = <&usb2phy0>;

I wonder what the correct place for this extcon property is. You defined it on SoC (RK3566) level, in my patch for the RK3568 EVB1 it is added on board level. Is this common to all RK356x variants?

Quoted 5 lines

Yes, the usb2phy is always available as an extcon unless you make a device that doesn't have usb2 capability.
In that case you'd have to override the device anyways. If we want to turn on default role otg here, we'd need this defined here as well or things break.

OK, so it seems to me that the extcon could or should enter the rk356x.dtsi (and can be removed from the rk3566.dtsi and the rk3568-evb1-v10.dts in this series). Is that correct?

Best regards,
Michael

Quoted 1 line

[...]

author
#14 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

Quoted 21 lines · Michael Riesch

Hi Peter,

Quoted 11 lines · Peter Geis

[...]

Quoted 9 lines

arch/arm64/boot/dts/rockchip/rk3566.dtsi power-domain@RK3568_PD_PIPE { · line 29

Quoted 5 lines
arch/arm64/boot/dts/rockchip/rk3566.dtsi +5 -0
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>;
+     phy-names = "usb2-phy";
+     extcon = <&usb2phy0>;

I wonder what the correct place for this extcon property is. You defined it on SoC (RK3566) level, in my patch for the RK3568 EVB1 it is added on board level. Is this common to all RK356x variants?

Quoted 5 lines

Yes, the usb2phy is always available as an extcon unless you make a device that doesn't have usb2 capability.
In that case you'd have to override the device anyways. If we want to turn on default role otg here, we'd need this defined here as well or things break.

Quoted 3 lines

OK, so it seems to me that the extcon could or should enter the rk356x.dtsi (and can be removed from the rk3566.dtsi and the rk3568-evb1-v10.dts in this series). Is that correct?

Apologies it seems I just missed this.
Yes, this could get moved to the base dtsi.
I'd prefer to do it as part of the next series supporting otg, as I've only been doing OTG development on the rk3566 and would prefer it be fully tested.
However if Johan prefers I can send another revision accomplishing this now.

Quoted 5 lines

Best regards,
Michael

Quoted 1 line

[...]

#15 lore raw

Re: [PATCH v3 5/7] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

Hi Peter,

Quoted 27 lines · Peter Geis
Quoted 21 lines · Michael Riesch

Hi Peter,

Quoted 11 lines · Peter Geis

[...]

Quoted 9 lines

arch/arm64/boot/dts/rockchip/rk3566.dtsi power-domain@RK3568_PD_PIPE { · line 29

Quoted 5 lines
arch/arm64/boot/dts/rockchip/rk3566.dtsi +5 -0
+
+&usb_host0_xhci {
+     phys = <&usb2phy0_otg>;
+     phy-names = "usb2-phy";
+     extcon = <&usb2phy0>;

I wonder what the correct place for this extcon property is. You defined it on SoC (RK3566) level, in my patch for the RK3568 EVB1 it is added on board level. Is this common to all RK356x variants?

Quoted 5 lines

Yes, the usb2phy is always available as an extcon unless you make a device that doesn't have usb2 capability.
In that case you'd have to override the device anyways. If we want to turn on default role otg here, we'd need this defined here as well or things break.

Quoted 3 lines

OK, so it seems to me that the extcon could or should enter the rk356x.dtsi (and can be removed from the rk3566.dtsi and the rk3568-evb1-v10.dts in this series). Is that correct?

Quoted 5 lines

Apologies it seems I just missed this.
Yes, this could get moved to the base dtsi.
I'd prefer to do it as part of the next series supporting otg, as I've only been doing OTG development on the rk3566 and would prefer it be fully tested.

Thanks for the clarification, that'll be fine for me.

Best regards,
Michael

Quoted 7 lines

However if Johan prefers I can send another revision accomplishing this now.

Quoted 5 lines

Best regards,
Michael

Quoted 1 line

[...]