Skip to contentSkip to conversation

Add SATA and USB to BPI-R2-Pro board

PATCH Applied Frank Wunderlich 2 participants 4 messages Apr 9, 2022 – Apr 10, 2022

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover Add SATA and USB to BPI-R2-Pro board

From: Frank Wunderlich <[email protected]>

Add necessary nodes for SATA and USB-Support on Bananapi-R2-Pro Board.

it depends on "enable usb support on rk356x" series from Peter Geis

https://patchwork.kernel.org/project/linux-rockchip/list/?series=630470

and a fixup-Patch changing clock names which should be squashed into above series in v6

ref_clk => ref
suspend_clk => suspend
bus_clk => bus_early

Frank Wunderlich (2):
arm64: dts: rockchip: Add USB nodes for BPI-R2-Pro
arm64: dts: rockchip: Add SATA support to BPI-R2-Pro

 .../boot/dts/rockchip/rk3568-bpi-r2-pro.dts   | 102 ++++++++++++++++++
 1 file changed, 102 insertions(+)
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/2 arm64: dts: rockchip: Add USB nodes for BPI-R2-Pro

From: Frank Wunderlich <[email protected]>

Add usb2 nodes to Bananapi R2 Pro board

---
 .../boot/dts/rockchip/rk3568-bpi-r2-pro.dts   | 93 +++++++++++++++++++
 1 file changed, 93 insertions(+)
arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts +93 -0
index 067fe4a6b178..879557595a64 100644
@@ -73,6 +73,50 @@ vcc5v0_sys: vcc5v0-sys {
 		regulator-max-microvolt = <5000000>;
 		vin-supply = <&dc_12v>;
 	};
+
+	vcc5v0_usb: vcc5v0_usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_usb_host: vcc5v0-usb-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_host_en>;
+		regulator-name = "vcc5v0_usb_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_otg: vcc5v0-usb-otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+};
+
+&combphy0 {
+	/* used for USB3 */
+	status = "okay";
+};
+
+&combphy1 {
+	/* used for USB3 */
+	status = "okay";
 };
 
 &gmac0 {
@@ -368,6 +412,16 @@ pmic_int: pmic_int {
 				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
+
+	usb {
+		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &pmu_io_domains {
@@ -485,3 +539,42 @@ &uart9 {
 	pinctrl-0 = <&uart9m1_xfer>;
 	status = "disabled";
 };
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	extcon = <&usb2phy0>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
Signature · 1 line
2.25.1
#2 lore raw

PATCH 2/2 arm64: dts: rockchip: Add SATA support to BPI-R2-Pro

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Enable the Combphy and Sata nodes in Bananapi R2 Pro Board.

---
 arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts +9 -0
index 879557595a64..40cf2236c0b6 100644
@@ -119,6 +119,11 @@ &combphy1 {
 	status = "okay";
 };
 
+&combphy2 {
+	/* used for SATA */
+	status = "okay";
+};
+
 &gmac0 {
 	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
 	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
@@ -484,6 +489,10 @@ &saradc {
 	status = "okay";
 };
 
+&sata2 {
+	status = "okay";
+};
+
 &sdhci {
 	bus-width = <8>;
 	max-frequency = <200000000>;
Signature · 1 line
2.25.1
maintainer Applied
#3 lore raw
In reply to Frank Wunderlich
Quoted 10 lines · Frank Wunderlich

Add necessary nodes for SATA and USB-Support on Bananapi-R2-Pro Board.

it depends on "enable usb support on rk356x" series from Peter Geis

https://patchwork.kernel.org/project/linux-rockchip/list/?series=630470

and a fixup-Patch changing clock names which should be squashed into above series in v6

[...]

Applied, thanks!

[1/2] arm64: dts: rockchip: Add USB nodes for BPI-R2-Pro

      commit: f29ffce32b4e1204b67f82fd80584ec4173cca54
[2/2] arm64: dts: rockchip: Add SATA support to BPI-R2-Pro
      commit: 551e645fed5dd2ed4c81c9e3d3b4827862f51dc6

Best regards,

Signature · 1 line
Heiko Stuebner <[email protected]>