Skip to contentSkip to conversation

common/board_f: remove XTRN_DECLARE_GLOBAL_DATA_PTR dead code

PATCH In review Ovidiu Panait 3 participants 10 messages Sep 13, 2022 – Oct 7, 2022

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/4 common/board_f: remove XTRN_DECLARE_GLOBAL_DATA_PTR dead code

The XTRN_DECLARE_GLOBAL_DATA_PTR declarations in ppc code are permanently commented out, so there are no users for this macro:
#if 1
#define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("r2")
#else /* We could use plain global data, but the resulting code is bigger */
#define XTRN_DECLARE_GLOBAL_DATA_PTR extern
#define DECLARE_GLOBAL_DATA_PTR XTRN_DECLARE_GLOBAL_DATA_PTR \
gd_t *gd
#endif

Remove all references to this macro, but add a documentation note regarding the possibility of using plain global data for the GD pointer.

---

Changes in v2:
- update global data documentation with the info provided by Wolfgang

 arch/powerpc/include/asm/global_data.h |  6 ------
 common/board_f.c                       | 11 -----------
 doc/develop/global_data.rst            |  5 +++++
 3 files changed, 5 insertions(+), 17 deletions(-)
arch/powerpc/include/asm/global_data.h +0 -6
index 6709e692e6..6ed21c781f 100644
@@ -92,12 +92,6 @@ struct arch_global_data {
 
 #include <asm-generic/global_data.h>
 
-#if 1
 #define DECLARE_GLOBAL_DATA_PTR     register volatile gd_t *gd asm ("r2")
-#else /* We could use plain global data, but the resulting code is bigger */
-#define XTRN_DECLARE_GLOBAL_DATA_PTR	extern
-#define DECLARE_GLOBAL_DATA_PTR     XTRN_DECLARE_GLOBAL_DATA_PTR \
-				    gd_t *gd
-#endif
 
 #endif /* __ASM_GBL_DATA_H */
common/board_f.c +0 -11
index 18e2246733..f4238d4c90 100644
@@ -57,18 +57,7 @@
 #include <dm/root.h>
 #include <linux/errno.h>
 
-/*
- * Pointer to initial global data area
- *
- * Here we initialize it if needed.
- */
-#ifdef XTRN_DECLARE_GLOBAL_DATA_PTR
-#undef	XTRN_DECLARE_GLOBAL_DATA_PTR
-#define XTRN_DECLARE_GLOBAL_DATA_PTR	/* empty = allocate here */
-DECLARE_GLOBAL_DATA_PTR = (gd_t *)(CONFIG_SYS_INIT_GD_ADDR);
-#else
 DECLARE_GLOBAL_DATA_PTR;
-#endif
 
 /*
  * TODO([email protected]): IMO this code should be
doc/develop/global_data.rst +5 -0
index 2ac893de49..d143f27eed 100644
@@ -36,6 +36,11 @@ On most architectures the global data pointer is stored in a register.
 
 The sandbox, x86_64, and Xtensa are notable exceptions.
 
+Current implementation uses a register for the GD pointer because this results
+in smaller code. However, using plain global data for the GD pointer would be
+possible too (and simpler, as it does not require the reservation of a specific
+register for it), but the resulting code is bigger.
+
 Clang for ARM does not support assigning a global register. When using Clang
 gd is defined as an inline function using assembly code. This adds a few bytes
 to the code size.
Signature · 1 line
2.25.1
#1 lore raw

PATCH v2 2/4 common/board_f: move CONFIG_MACH_TYPE logic to arch/arm/lib/bdinfo.c

asm/mach_type.h header and CONFIG_MACH_TYPE macro are arm-specific, so move related bdinfo logic to arch_setup_bdinfo() in arch/arm/lib/bdinfo.c.

---

Changes in v2:
- add "Reviewed-by" tag from Simon

 arch/arm/lib/bdinfo.c | 12 ++++++++++++
 common/board_f.c      |  7 -------
 2 files changed, 12 insertions(+), 7 deletions(-)
arch/arm/lib/bdinfo.c +12 -0
index b22ee07b85..826e09e72c 100644
@@ -9,9 +9,21 @@
 #include <common.h>
 #include <init.h>
 #include <asm/global_data.h>
+#include <asm/mach-types.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
+int arch_setup_bdinfo(void)
+{
+#ifdef CONFIG_MACH_TYPE
+	struct bd_info *bd = gd->bd;
+
+	bd->bi_arch_number = CONFIG_MACH_TYPE; /* board id for Linux */
+#endif
+
+	return 0;
+}
+
 void arch_print_bdinfo(void)
 {
 	struct bd_info *bd = gd->bd;
common/board_f.c +0 -7
index f4238d4c90..3789708a30 100644
@@ -45,9 +45,6 @@
 #include <video.h>
 #include <watchdog.h>
 #include <asm/cache.h>
-#ifdef CONFIG_MACH_TYPE
-#include <asm/mach-types.h>
-#endif
 #if defined(CONFIG_MP) && defined(CONFIG_PPC)
 #include <asm/mp.h>
 #endif
@@ -588,10 +585,6 @@ int setup_bdinfo(void)
 		bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE;  /* size  of SRAM */
 	}
 
-#ifdef CONFIG_MACH_TYPE
-	bd->bi_arch_number = CONFIG_MACH_TYPE; /* board id for Linux */
-#endif
-
 	return arch_setup_bdinfo();
 }
 
Signature · 1 line
2.25.1
#2 lore raw

Re: [PATCH v2 2/4] common/board_f: move CONFIG_MACH_TYPE logic to arch/arm/lib/bdinfo.c

Quoted 5 lines · Ovidiu Panait

asm/mach_type.h header and CONFIG_MACH_TYPE macro are arm-specific, so move related bdinfo logic to arch_setup_bdinfo() in arch/arm/lib/bdinfo.c.

Applied to u-boot/master, thanks!

Signature · 1 line
Tom
#3 lore raw

PATCH v2 3/4 common/board_f: introduce arch_setup_dest_addr()

In reply to Ovidiu Panait

In order to move ppc-specific code out of setup_dest_addr(), provide an arch-specific variant arch_setup_dest_addr(), that can be used by architecture code to fix up the initial reloc address.

It is called at the end of setup_dest_addr() initcall and the default implementation is a nop stub.

---

Changes in v2:
- add "Reviewed-by" tag from Simon

 arch/powerpc/lib/stack.c | 17 +++++++++++++++++
 common/board_f.c         | 21 +++++++--------------
 include/init.h           | 13 +++++++++++++
 3 files changed, 37 insertions(+), 14 deletions(-)
arch/powerpc/lib/stack.c +17 -0
index f2a4652e08..2e731aa870 100644
@@ -13,6 +13,7 @@
 #include <common.h>
 #include <init.h>
 #include <asm/global_data.h>
+#include <asm/mp.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -30,3 +31,19 @@ int arch_reserve_stacks(void)
 
 	return 0;
 }
+
+int arch_setup_dest_addr(void)
+{
+#if defined(CONFIG_MP) && (defined(CONFIG_MPC86xx) || defined(CONFIG_E500))
+	/*
+	 * We need to make sure the location we intend to put secondary core
+	 * boot code is reserved and not used by any part of u-boot
+	 */
+	if (gd->relocaddr > determine_mp_bootpg(NULL)) {
+		gd->relocaddr = determine_mp_bootpg(NULL);
+		debug("Reserving MP boot page to %08lx\n", gd->relocaddr);
+	}
+#endif
+
+	return 0;
+}
common/board_f.c +7 -14
index 3789708a30..96458c5151 100644
@@ -45,9 +45,6 @@
 #include <video.h>
 #include <watchdog.h>
 #include <asm/cache.h>
-#if defined(CONFIG_MP) && defined(CONFIG_PPC)
-#include <asm/mp.h>
-#endif
 #include <asm/global_data.h>
 #include <asm/io.h>
 #include <asm/sections.h>
@@ -307,6 +304,11 @@ __weak ulong board_get_usable_ram_top(ulong total_size)
 	return gd->ram_top;
 }
 
+__weak int arch_setup_dest_addr(void)
+{
+	return 0;
+}
+
 static int setup_dest_addr(void)
 {
 	debug("Monitor len: %08lX\n", gd->mon_len);
@@ -334,17 +336,8 @@ static int setup_dest_addr(void)
 	gd->ram_top = board_get_usable_ram_top(gd->mon_len);
 	gd->relocaddr = gd->ram_top;
 	debug("Ram top: %08lX\n", (ulong)gd->ram_top);
-#if defined(CONFIG_MP) && (defined(CONFIG_MPC86xx) || defined(CONFIG_E500))
-	/*
-	 * We need to make sure the location we intend to put secondary core
-	 * boot code is reserved and not used by any part of u-boot
-	 */
-	if (gd->relocaddr > determine_mp_bootpg(NULL)) {
-		gd->relocaddr = determine_mp_bootpg(NULL);
-		debug("Reserving MP boot page to %08lx\n", gd->relocaddr);
-	}
-#endif
-	return 0;
+
+	return arch_setup_dest_addr();
 }
 
 #ifdef CONFIG_PRAM
include/init.h +13 -0
index 7b8f62c121..448da34b46 100644
@@ -103,6 +103,19 @@ phys_size_t get_effective_memsize(void);
 
 int testdram(void);
 
+/**
+ * arch_setup_dest_addr() - Fix up initial reloc address
+ *
+ * This is called in generic board init sequence in common/board_f.c at the end
+ * of the setup_dest_addr() initcall. Each architecture could provide this
+ * function to make adjustments to the initial reloc address.
+ *
+ * If an implementation is not provided, it will just be a nop stub.
+ *
+ * Return: 0 if OK
+ */
+int arch_setup_dest_addr(void);
+
 /**
  * arch_reserve_stacks() - Reserve all necessary stacks
  *
Signature · 1 line
2.25.1
#4 lore raw

Re: [PATCH v2 3/4] common/board_f: introduce arch_setup_dest_addr()

Quoted 9 lines · Ovidiu Panait

In order to move ppc-specific code out of setup_dest_addr(), provide an arch-specific variant arch_setup_dest_addr(), that can be used by architecture code to fix up the initial reloc address.

It is called at the end of setup_dest_addr() initcall and the default implementation is a nop stub.

Applied to u-boot/master, thanks!

Signature · 1 line
Tom
#5 lore raw

PATCH v2 4/4 common/board_f: drop ifdefs around header includes

In reply to Ovidiu Panait

Drop the remaining ifdef around spl.h include.

---

Changes in v2:
- add "Reviewed-by" tag from Simon

 common/board_f.c | 2 --
 1 file changed, 2 deletions(-)
common/board_f.c +0 -2
index 96458c5151..4db1626c29 100644
@@ -35,9 +35,7 @@
 #include <post.h>
 #include <relocate.h>
 #include <serial.h>
-#ifdef CONFIG_SPL
 #include <spl.h>
-#endif
 #include <status_led.h>
 #include <sysreset.h>
 #include <timer.h>
Signature · 1 line
2.25.1
Reviewed-by on v2 1/4
#7 lore raw
In reply to Ovidiu Panait
Quoted 17 lines · Ovidiu Panait

The XTRN_DECLARE_GLOBAL_DATA_PTR declarations in ppc code are permanently commented out, so there are no users for this macro:

 #if 1
   #define DECLARE_GLOBAL_DATA_PTR   register volatile gd_t *gd asm ("r2")
 #else /* We could use plain global data, but the resulting code is bigger */
   #define XTRN_DECLARE_GLOBAL_DATA_PTR   extern
   #define DECLARE_GLOBAL_DATA_PTR     XTRN_DECLARE_GLOBAL_DATA_PTR \
                                       gd_t *gd

#endif

Remove all references to this macro, but add a documentation note regarding the possibility of using plain global data for the GD pointer.

---

Quoted 7 lines

Changes in v2:
- update global data documentation with the info provided by Wolfgang

 arch/powerpc/include/asm/global_data.h |  6 ------
 common/board_f.c                       | 11 -----------
 doc/develop/global_data.rst            |  5 +++++
 3 files changed, 5 insertions(+), 17 deletions(-)
Reviewed-by on v2 1/4
#8 lore raw
In reply to Ovidiu Panait
Quoted 8 lines · Ovidiu Panait

The XTRN_DECLARE_GLOBAL_DATA_PTR declarations in ppc code are permanently commented out, so there are no users for this macro:

 #if 1
   #define DECLARE_GLOBAL_DATA_PTR   register volatile gd_t *gd asm ("r2")
 #else /* We could use plain global data, but the resulting code is bigger */
   #define XTRN_DECLARE_GLOBAL_DATA_PTR   extern
   #define DECLARE_GLOBAL_DATA_PTR     XTRN_DECLARE_GLOBAL_DATA_PTR \
                                       gd_t *gd
Quoted 6 lines

#endif

Remove all references to this macro, but add a documentation note regarding the possibility of using plain global data for the GD pointer.

Signature · 1 line
Tom
#9 lore raw
In reply to Ovidiu Panait
Quoted 8 lines · Ovidiu Panait

The XTRN_DECLARE_GLOBAL_DATA_PTR declarations in ppc code are permanently commented out, so there are no users for this macro:

 #if 1
   #define DECLARE_GLOBAL_DATA_PTR   register volatile gd_t *gd asm ("r2")
 #else /* We could use plain global data, but the resulting code is bigger */
   #define XTRN_DECLARE_GLOBAL_DATA_PTR   extern
   #define DECLARE_GLOBAL_DATA_PTR     XTRN_DECLARE_GLOBAL_DATA_PTR \
                                       gd_t *gd
Quoted 8 lines

#endif

Remove all references to this macro, but add a documentation note regarding the possibility of using plain global data for the GD pointer.

Applied to u-boot/master, thanks!

Signature · 1 line
Tom