Skip to contentSkip to conversation

Docs/admin-buide/mm/damon/usage: minor fixes

PATCH Applied SeongJae Park 1 participant 3 messages Oct 24, 2022

Subsystems (4)
lore
Share & tools
lore

SeongJae Park

author maintainer
#0 lore raw

cover Docs/admin-buide/mm/damon/usage: minor fixes

DAMON usage document contains an unclear description and a wrong usage example. This patchset fixes the two minor problems.

SeongJae Park (2):
Docs/admin-guide/mm/damon/usage: describe the rules of sysfs region
directories
Docs/admin-guide/mm/damon/usage: Fix wrong usage example of
init_regions file

 Documentation/admin-guide/mm/damon/usage.rst | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
Signature · 1 line
2.25.1
author maintainer
#1 lore raw

PATCH 1/2 Docs/admin-guide/mm/damon/usage: describe the rules of sysfs region directories

Target region directories of DAMON sysfs interface should contain no overlap and sorted by the address, but not clearly documented. Actually, a user had an issue[1] due to the poor documentation. Add clear description of it on the usage document.

[1] https://lore.kernel.org/damon/CAEZ6=UNUcH2BvJj++OrT=XQLdkidU79wmCO=tantSOB36pPNTg@mail.gmail.com/

---
 Documentation/admin-guide/mm/damon/usage.rst | 3 +++
 1 file changed, 3 insertions(+)
Documentation/admin-guide/mm/damon/usage.rst +3 -0
index b47b0cbbd491..89d9a4f75a29 100644
@@ -235,6 +235,9 @@ In each region directory, you will find two files (``start`` and ``end``).  You
 can set and get the start and end addresses of the initial monitoring target
 region by writing to and reading from the files, respectively.
 
+Each region should not overlap with others.  ``end`` of directory ``N`` should
+be equal or smaller than ``start`` of directory ``N+1``.
+
 contexts/<N>/schemes/
 ---------------------
 
Signature · 1 line
2.25.1
author maintainer
#2 lore raw

PATCH 2/2 Docs/admin-guide/mm/damon/usage: Fix wrong usage example of init_regions file

In reply to SeongJae Park

DAMON debugfs interface assumes the users will write all inputs at once. However, redirecting a string of multiple lines sometimes end up writing line by line. Therefore, the example usage of 'init_regions' file, which writes input as a string of multiple lines can fail. Fix it to use a single line string instead. Also update the description of the usage to not assume users will write inputs in multiple lines.

---
 Documentation/admin-guide/mm/damon/usage.rst | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)
Documentation/admin-guide/mm/damon/usage.rst +6 -5
index 89d9a4f75a29..c17e02e1e426 100644
@@ -468,8 +468,9 @@ regions in case of physical memory monitoring.  Therefore, users should set the
 monitoring target regions by themselves.
 
 In such cases, users can explicitly set the initial monitoring target regions
-as they want, by writing proper values to the ``init_regions`` file.  Each line
-of the input should represent one region in below form.::
+as they want, by writing proper values to the ``init_regions`` file.  The input
+should be a sequence of three integers separated by white spaces that represent
+one region in below form.::
 
     <target idx> <start address> <end address>
 
@@ -484,9 +485,9 @@ ranges, ``20-40`` and ``50-100`` as that of pid 4242, which is the second one
     # cd <debugfs>/damon
     # cat target_ids
     42 4242
-    # echo "0   1       100
-            0   100     200
-            1   20      40
+    # echo "0   1       100 \
+            0   100     200 \
+            1   20      40  \
             1   50      100" > init_regions
 
 Note that this sets the initial monitoring target regions only.  In case of
Signature · 1 line
2.25.1