gpiolib: acpi: Add a ignore wakeup quirk for Clevo NH5xAx
PATCH 1/1 gpiolib: acpi: Add a ignore wakeup quirk for Clevo NH5xAx
commit 1796f808e4bb ("HID: i2c-hid: acpi: Stop setting wakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.
However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up. As soon as the system suspends the touchpad loses power and then the system wakes up.
To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
--- drivers/gpio/gpiolib-acpi.c | 12 ++++++++++++ 1 file changed, 12 insertions(+)
drivers/gpio/gpiolib-acpi.c +12 -0
@@ -1612,6 +1612,18 @@ static const struct dmi_system_id gpiolib_acpi_quirks[] __initconst = { .ignore_wake = "ELAN0415:00@9", }, }, + { +/* +* Spurious wakeups from TP_ATTN# pin +* Found in BIOS 1.7.7 +*/ + .matches = { + DMI_MATCH(DMI_BOARD_NAME, "NH5xAx"), + }, + .driver_data = &(struct acpi_gpiolib_dmi_quirk) { + .ignore_wake = "SYNA1202:00@16", + }, + }, {}/* Terminating entry */ };
Signature · 1 line
2.34.1
Quoted 7 lines · Werner Sembach
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up.
I'm not sure I understand the issue here. From what you say here it seems correct ACPI description.
Quoted 5 lines
As soon as the
system suspends the touchpad loses power and then the system wakes up.To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
I'm not against fixing this, but wouldn't be better to actually target the root cause and have a different quirk? Or is it me who didn't get what is the root cause?
Signature · 2 lines
With Best Regards, Andy Shevchenko
Am 10.02.23 um 18:04 schrieb Andy Shevchenko:
Quoted 10 lines · Werner Sembach
Quoted 7 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up.
I'm not sure I understand the issue here. From what you say here it seems correct ACPI description.
TBH I copied the commit description from https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4cb786180dfb5258ff3111181b5e4ecb1d4a297b which is for a different device having the exact same problem.
Quoted 10 lines
Quoted 6 lines
As soon as the
system suspends the touchpad loses power and then the system wakes up.To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
I'm not against fixing this, but wouldn't be better to actually target the root cause and have a different quirk? Or is it me who didn't get what is the root cause?
I missed to reference the original discussion while copying the description: https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627 (Note that it's a somewhat convoluted issue spanning multiple bugs when you scroll up from that particular linked comment, which are however irrelevant for this patch)
I'm not deep into how ACPI defined IRQ work so maybe not a good idea for me summing it up, as I might have misunderstood parts of it ^^
I added the other ones from there to the cc.
Quoted 6 lines · Werner Sembach
Am 10.02.23 um 18:04 schrieb Andy Shevchenko:
Quoted 5 lines · Werner Sembach
Quoted 4 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up.
I'm not sure I understand the issue here. From what you say here it seems correct ACPI description.
TBH I copied the commit description from https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4cb786180dfb5258ff3111181b5e4ecb1d4a297b
which is for a different device having the exact same problem.
Yeah, and I reviewed that and seems paid no attention to this detail.
So, ActiveLow + PullUp is the _right_ thing to do in ACPI. The problem seems somewhere else.
Mario, can we have an access to the schematics of the affected pin to understand better what's going on?
Or is that description missing some crucial detail?
Quoted 9 lines
Quoted 9 lines
Quoted 5 lines
As soon as the
system suspends the touchpad loses power and then the system wakes up.To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
I'm not against fixing this, but wouldn't be better to actually target the root cause and have a different quirk? Or is it me who didn't get what is the root cause?
Quoted 8 lines
I missed to reference the original discussion while copying the description:
https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627 (Note that it's a somewhat convoluted issue spanning multiple bugs when you scroll up from that particular linked comment, which are however irrelevant for this patch)I'm not deep into how ACPI defined IRQ work so maybe not a good idea for me summing it up, as I might have misunderstood parts of it ^^
The GpioIo() and GpioInt() resources have gaps in them, due to this some additional information is required or some heuristics is used to deduct the settings.
All this is described in
https://www.kernel.org/doc/html/latest/firmware-guide/acpi/gpio-properties.html
Quoted 1 line
I added the other ones from there to the cc.
Thank you.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Quoted 16 lines · Andy Shevchenko
Quoted 6 lines · Werner Sembach
Am 10.02.23 um 18:04 schrieb Andy Shevchenko:
Quoted 5 lines · Werner Sembach
Quoted 4 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up.
I'm not sure I understand the issue here. From what you say here it seems correct ACPI description.
TBH I copied the commit description from https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4cb786180dfb5258ff3111181b5e4ecb1d4a297b
which is for a different device having the exact same problem.Yeah, and I reviewed that and seems paid no attention to this detail.
Quoted 7 lines
So, ActiveLow + PullUp is the _right_ thing to do in ACPI. The problem seems somewhere else.
Mario, can we have an access to the schematics of the affected pin to understand better what's going on?
Or is that description missing some crucial detail?
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Quoted 27 lines
Quoted 9 lines
Quoted 9 lines
Quoted 5 lines
As soon as the
system suspends the touchpad loses power and then the system wakes up.To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
I'm not against fixing this, but wouldn't be better to actually target the root cause and have a different quirk? Or is it me who didn't get what is the root cause?
Quoted 8 lines
I missed to reference the original discussion while copying the description:
https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627 (Note that it's a somewhat convoluted issue spanning multiple bugs when you scroll up from that particular linked comment, which are however irrelevant for this patch)I'm not deep into how ACPI defined IRQ work so maybe not a good idea for me summing it up, as I might have misunderstood parts of it ^^
The
GpioIo()andGpioInt()resources have gaps in them, due to this some additional information is required or some heuristics is used to deduct the settings.All this is described in
https://www.kernel.org/doc/html/latest/firmware-guide/acpi/gpio-properties.htmlQuoted 1 line
I added the other ones from there to the cc.
Thank you.
Quoted 23 lines · Mario Limonciello
Quoted 22 lines · Andy Shevchenko
Quoted 6 lines · Werner Sembach
Am 10.02.23 um 18:04 schrieb Andy Shevchenko:
Quoted 5 lines · Werner Sembach
Quoted 4 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up.
I'm not sure I understand the issue here. From what you say here it seems correct ACPI description.
TBH I copied the commit description from https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4cb786180dfb5258ff3111181b5e4ecb1d4a297b
which is for a different device having the exact same problem.Yeah, and I reviewed that and seems paid no attention to this detail.
So, ActiveLow + PullUp is the _right_ thing to do in ACPI. The problem seems somewhere else.
Mario, can we have an access to the schematics of the affected pin to understand better what's going on?
Quoted 7 lines
Quoted 1 line
Or is that description missing some crucial detail?
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Thank you!
I have looked at the schematics and read discussion.
So, the conclusion that this is a BIOS bug is incorrect in my opinion. The problem is either in the PMIC/EC firmware that shouldn't shut down 3.3VS signal for a while or on the PCB level, so that pull up should be connected to another power source that stays on.
This means the description on the initial patch with the same issue is incorrect.
Do we know the power sequence on the suspend to see which and how on the time line the power sources are off/on?
Quoted 26 lines
Quoted 26 lines
Quoted 9 lines
Quoted 9 lines
Quoted 5 lines
As soon as the
system suspends the touchpad loses power and then the system wakes up.To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
I'm not against fixing this, but wouldn't be better to actually target the root cause and have a different quirk? Or is it me who didn't get what is the root cause?
Quoted 8 lines
I missed to reference the original discussion while copying the description:
https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627 (Note that it's a somewhat convoluted issue spanning multiple bugs when you scroll up from that particular linked comment, which are however irrelevant for this patch)I'm not deep into how ACPI defined IRQ work so maybe not a good idea for me summing it up, as I might have misunderstood parts of it ^^
The
GpioIo()andGpioInt()resources have gaps in them, due to this some additional information is required or some heuristics is used to deduct the settings.All this is described in
https://www.kernel.org/doc/html/latest/firmware-guide/acpi/gpio-properties.htmlQuoted 1 line
I added the other ones from there to the cc.
Thank you.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Am 13.02.23 um 15:37 schrieb Andy Shevchenko:
Quoted 18 lines · Mario Limonciello
Quoted 17 lines · Andy Shevchenko
Quoted 16 lines · Werner Sembach
Quoted 6 lines
Am 10.02.23 um 18:04 schrieb Andy Shevchenko:
Quoted 5 lines · Werner Sembach
Quoted 4 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up.
I'm not sure I understand the issue here. From what you say here it seems correct ACPI description.
TBH I copied the commit description from https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4cb786180dfb5258ff3111181b5e4ecb1d4a297b
which is for a different device having the exact same problem.Yeah, and I reviewed that and seems paid no attention to this detail.
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
So, ActiveLow + PullUp is the _right_ thing to do in ACPI. The problem seems somewhere else.
Mario, can we have an access to the schematics of the affected pin to understand better what's going on?
Or is that description missing some crucial detail?
Schematics for the NH5xAx can also be found on this unofficial clevo mirror (service manuals, scroll to end for schematics):
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zip
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AF1.zip
User: repo
PW: repo
Quoted 45 lines
Quoted 5 lines
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Thank you!
I have looked at the schematics and read discussion.So, the conclusion that this is a BIOS bug is incorrect in my opinion. The problem is either in the PMIC/EC firmware that shouldn't shut down 3.3VS signal for a while or on the PCB level, so that pull up should be connected to another power source that stays on.
This means the description on the initial patch with the same issue is incorrect.
Do we know the power sequence on the suspend to see which and how on the time line the power sources are off/on?
Quoted 26 lines
Quoted 26 lines
Quoted 9 lines
Quoted 9 lines
Quoted 5 lines
As soon as the
system suspends the touchpad loses power and then the system wakes up.To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
I'm not against fixing this, but wouldn't be better to actually target the root cause and have a different quirk? Or is it me who didn't get what is the root cause?
Quoted 8 lines
I missed to reference the original discussion while copying the description:
https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627 (Note that it's a somewhat convoluted issue spanning multiple bugs when you scroll up from that particular linked comment, which are however irrelevant for this patch)I'm not deep into how ACPI defined IRQ work so maybe not a good idea for me summing it up, as I might have misunderstood parts of it ^^
The
GpioIo()andGpioInt()resources have gaps in them, due to this some additional information is required or some heuristics is used to deduct the settings.All this is described in
https://www.kernel.org/doc/html/latest/firmware-guide/acpi/gpio-properties.htmlQuoted 1 line
I added the other ones from there to the cc.
Thank you.
SUSB#_EN
Quoted 31 lines · Werner Sembach
Am 13.02.23 um 15:37 schrieb Andy Shevchenko:
Quoted 18 lines · Mario Limonciello
Quoted 17 lines · Andy Shevchenko
Quoted 16 lines · Werner Sembach
Quoted 6 lines
Am 10.02.23 um 18:04 schrieb Andy Shevchenko:
Quoted 5 lines · Werner Sembach
Quoted 4 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up.
I'm not sure I understand the issue here. From what you say here it seems correct ACPI description.
TBH I copied the commit description from https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4cb786180dfb5258ff3111181b5e4ecb1d4a297b
which is for a different device having the exact same problem.Yeah, and I reviewed that and seems paid no attention to this detail.
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
So, ActiveLow + PullUp is the _right_ thing to do in ACPI. The problem seems somewhere else.
Mario, can we have an access to the schematics of the affected pin to understand better what's going on?
Or is that description missing some crucial detail?
Schematics for the NH5xAx can also be found on this unofficial clevo mirror (service manuals, scroll to end for schematics):
Quoted 28 lines
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zip
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AF1.zip
User: repo
PW: repo
Quoted 20 lines
Quoted 5 lines
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Thank you!
I have looked at the schematics and read discussion.So, the conclusion that this is a BIOS bug is incorrect in my opinion. The problem is either in the PMIC/EC firmware that shouldn't shut down 3.3VS signal for a while or on the PCB level, so that pull up should be connected to another power source that stays on.
This means the description on the initial patch with the same issue is incorrect.
Do we know the power sequence on the suspend to see which and how on the time line the power sources are off/on?
If you look at the load switch for 3.3VS, its EN2 pin is connected to SUSB#_EN which is connected to SUSB# which is connected to AND(SUSB#_PCH -> SLP_S3_L, PM_SLP_S0 -> S0A3_GPIO). So there is no PMIC/EC firmware that is incharge of this. I guess I'm not quite sure how they have S0A3_GPIO configured, so maybe I have an invert wrong.
The EC does control DD_ON which controls the 3.3V and 5V rails.
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 9 lines
Quoted 9 lines
Quoted 5 lines
As soon as the
system suspends the touchpad loses power and then the system wakes up.To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
I'm not against fixing this, but wouldn't be better to actually target the root cause and have a different quirk? Or is it me who didn't get what is the root cause?
Quoted 8 lines
I missed to reference the original discussion while copying the description:
https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627 (Note that it's a somewhat convoluted issue spanning multiple bugs when you scroll up from that particular linked comment, which are however irrelevant for this patch)I'm not deep into how ACPI defined IRQ work so maybe not a good idea for me summing it up, as I might have misunderstood parts of it ^^
The
GpioIo()andGpioInt()resources have gaps in them, due to this some additional information is required or some heuristics is used to deduct the settings.All this is described in
https://www.kernel.org/doc/html/latest/firmware-guide/acpi/gpio-properties.htmlQuoted 1 line
I added the other ones from there to the cc.
Thank you.
Quoted 59 lines · Raul Rangel
Quoted 30 lines · Werner Sembach
Am 13.02.23 um 15:37 schrieb Andy Shevchenko:
Quoted 18 lines · Mario Limonciello
Quoted 17 lines · Andy Shevchenko
Quoted 16 lines · Werner Sembach
Quoted 6 lines
Am 10.02.23 um 18:04 schrieb Andy Shevchenko:
Quoted 5 lines · Werner Sembach
Quoted 4 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up.
I'm not sure I understand the issue here. From what you say here it seems correct ACPI description.
TBH I copied the commit description from https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4cb786180dfb5258ff3111181b5e4ecb1d4a297b
which is for a different device having the exact same problem.Yeah, and I reviewed that and seems paid no attention to this detail.
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
So, ActiveLow + PullUp is the _right_ thing to do in ACPI. The problem seems somewhere else.
Mario, can we have an access to the schematics of the affected pin to understand better what's going on?
Or is that description missing some crucial detail?
Schematics for the NH5xAx can also be found on this unofficial clevo mirror (service manuals, scroll to end for schematics):
Quoted 27 lines
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zip
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AF1.zip
User: repo
PW: repo
Quoted 19 lines
Quoted 5 lines
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Thank you!
I have looked at the schematics and read discussion.So, the conclusion that this is a BIOS bug is incorrect in my opinion. The problem is either in the PMIC/EC firmware that shouldn't shut down 3.3VS signal for a while or on the PCB level, so that pull up should be connected to another power source that stays on.
This means the description on the initial patch with the same issue is incorrect.
Do we know the power sequence on the suspend to see which and how on the time line the power sources are off/on?
Quoted 7 lines
If you look at the load switch for 3.3VS, its EN2 pin is connected to SUSB#_EN which is connected to SUSB# which is connected to
AND(SUSB#_PCH -> SLP_S3_L, PM_SLP_S0 -> S0A3_GPIO). So there is no PMIC/EC firmware that is incharge of this. I guess I'm not quite sure how they haveS0A3_GPIOconfigured, so maybe I have an invert wrong.The EC does control
DD_ONwhich controls the 3.3V and 5V rails.
On page 6 of the schematics I see the U7 that forms SUSB# from SUSB#_APU (which corresponds to what you said) _and_ EC_EN, which is GPIO from IT5570, which is EC.
Are you using different schematics? I'm using the one from FDO bug report.
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 9 lines
Quoted 9 lines
Quoted 5 lines
As soon as the
system suspends the touchpad loses power and then the system wakes up.To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
I'm not against fixing this, but wouldn't be better to actually target the root cause and have a different quirk? Or is it me who didn't get what is the root cause?
Quoted 8 lines
I missed to reference the original discussion while copying the description:
https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627 (Note that it's a somewhat convoluted issue spanning multiple bugs when you scroll up from that particular linked comment, which are however irrelevant for this patch)I'm not deep into how ACPI defined IRQ work so maybe not a good idea for me summing it up, as I might have misunderstood parts of it ^^
The
GpioIo()andGpioInt()resources have gaps in them, due to this some additional information is required or some heuristics is used to deduct the settings.All this is described in
https://www.kernel.org/doc/html/latest/firmware-guide/acpi/gpio-properties.htmlQuoted 1 line
I added the other ones from there to the cc.
Thank you.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Quoted 66 lines · Andy Shevchenko
Quoted 65 lines · Raul Rangel
Quoted 30 lines · Werner Sembach
Am 13.02.23 um 15:37 schrieb Andy Shevchenko:
Quoted 18 lines · Mario Limonciello
Quoted 17 lines · Andy Shevchenko
Quoted 16 lines · Werner Sembach
Quoted 6 lines
Am 10.02.23 um 18:04 schrieb Andy Shevchenko:
Quoted 5 lines · Werner Sembach
Quoted 4 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up.
I'm not sure I understand the issue here. From what you say here it seems correct ACPI description.
TBH I copied the commit description from https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4cb786180dfb5258ff3111181b5e4ecb1d4a297b
which is for a different device having the exact same problem.Yeah, and I reviewed that and seems paid no attention to this detail.
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
So, ActiveLow + PullUp is the _right_ thing to do in ACPI. The problem seems somewhere else.
Mario, can we have an access to the schematics of the affected pin to understand better what's going on?
Or is that description missing some crucial detail?
Schematics for the NH5xAx can also be found on this unofficial clevo mirror (service manuals, scroll to end for schematics):
Quoted 27 lines
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zip
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AF1.zip
User: repo
PW: repo
Quoted 19 lines
Quoted 5 lines
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Thank you!
I have looked at the schematics and read discussion.So, the conclusion that this is a BIOS bug is incorrect in my opinion. The problem is either in the PMIC/EC firmware that shouldn't shut down 3.3VS signal for a while or on the PCB level, so that pull up should be connected to another power source that stays on.
This means the description on the initial patch with the same issue is incorrect.
Do we know the power sequence on the suspend to see which and how on the time line the power sources are off/on?
If you look at the load switch for 3.3VS, its EN2 pin is connected to SUSB#_EN which is connected to SUSB# which is connected to
AND(SUSB#_PCH -> SLP_S3_L, PM_SLP_S0 -> S0A3_GPIO). So there is no PMIC/EC firmware that is incharge of this. I guess I'm not quite sure how they haveS0A3_GPIOconfigured, so maybe I have an invert wrong.
Quoted 7 lines
Quoted 1 line
The EC does control
DD_ONwhich controls the 3.3V and 5V rails.On page 6 of the schematics I see the U7 that forms SUSB# from SUSB#_APU (which corresponds to what you said) _and_
EC_EN, which is GPIO from IT5570, which is EC.Are you using different schematics? I'm using the one from FDO bug report.
Just checked this one:
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zip
Also uses EC (SUSB_EC#).
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 9 lines
Quoted 9 lines
Quoted 5 lines
As soon as the
system suspends the touchpad loses power and then the system wakes up.To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
I'm not against fixing this, but wouldn't be better to actually target the root cause and have a different quirk? Or is it me who didn't get what is the root cause?
Quoted 8 lines
I missed to reference the original discussion while copying the description:
https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627 (Note that it's a somewhat convoluted issue spanning multiple bugs when you scroll up from that particular linked comment, which are however irrelevant for this patch)I'm not deep into how ACPI defined IRQ work so maybe not a good idea for me summing it up, as I might have misunderstood parts of it ^^
The
GpioIo()andGpioInt()resources have gaps in them, due to this some additional information is required or some heuristics is used to deduct the settings.All this is described in
https://www.kernel.org/doc/html/latest/firmware-guide/acpi/gpio-properties.htmlQuoted 1 line
I added the other ones from there to the cc.
Thank you.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Quoted 4 lines · Andy Shevchenko
Quoted 3 lines · Andy Shevchenko
Quoted 2 lines · Raul Rangel
Quoted 1 line · Werner Sembach
Am 13.02.23 um 15:37 schrieb Andy Shevchenko:
...
Quoted 43 lines
Quoted 43 lines
Quoted 31 lines
Quoted 30 lines
Schematics for the NH5xAx can also be found on this unofficial clevo mirror (service manuals, scroll to end for schematics):
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zip
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AF1.zip
User: repo
PW: repo
Quoted 19 lines
Quoted 5 lines
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Thank you!
I have looked at the schematics and read discussion.So, the conclusion that this is a BIOS bug is incorrect in my opinion. The problem is either in the PMIC/EC firmware that shouldn't shut down 3.3VS signal for a while or on the PCB level, so that pull up should be connected to another power source that stays on.
This means the description on the initial patch with the same issue is incorrect.
Do we know the power sequence on the suspend to see which and how on the time line the power sources are off/on?
Quoted 7 lines
If you look at the load switch for 3.3VS, its EN2 pin is connected to SUSB#_EN which is connected to SUSB# which is connected to
AND(SUSB#_PCH -> SLP_S3_L, PM_SLP_S0 -> S0A3_GPIO). So there is no PMIC/EC firmware that is incharge of this. I guess I'm not quite sure how they haveS0A3_GPIOconfigured, so maybe I have an invert wrong.The EC does control
DD_ONwhich controls the 3.3V and 5V rails.On page 6 of the schematics I see the U7 that forms SUSB# from SUSB#_APU (which corresponds to what you said) _and_
EC_EN, which is GPIO from IT5570, which is EC.
Quoted 6 lines
Quoted 1 line
Are you using different schematics? I'm using the one from FDO bug report.
Just checked this one:
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zipAlso uses EC (SUSB_EC#).
So this all makes me thing that either EC firmware is buggy or we have ACPI EC code in the kernel to fix.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Quoted 5 lines · Andy Shevchenko
Quoted 4 lines · Andy Shevchenko
Quoted 3 lines · Andy Shevchenko
Quoted 2 lines · Raul Rangel
Quoted 1 line · Werner Sembach
Am 13.02.23 um 15:37 schrieb Andy Shevchenko:
...
Quoted 43 lines
Quoted 43 lines
Quoted 43 lines
Quoted 31 lines
Quoted 30 lines
Schematics for the NH5xAx can also be found on this unofficial clevo mirror (service manuals, scroll to end for schematics):
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zip
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AF1.zip
User: repo
PW: repo
Quoted 19 lines
Quoted 5 lines
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Thank you!
I have looked at the schematics and read discussion.So, the conclusion that this is a BIOS bug is incorrect in my opinion. The problem is either in the PMIC/EC firmware that shouldn't shut down 3.3VS signal for a while or on the PCB level, so that pull up should be connected to another power source that stays on.
This means the description on the initial patch with the same issue is incorrect.
Do we know the power sequence on the suspend to see which and how on the time line the power sources are off/on?
Quoted 7 lines
If you look at the load switch for 3.3VS, its EN2 pin is connected to SUSB#_EN which is connected to SUSB# which is connected to
AND(SUSB#_PCH -> SLP_S3_L, PM_SLP_S0 -> S0A3_GPIO). So there is no PMIC/EC firmware that is incharge of this. I guess I'm not quite sure how they haveS0A3_GPIOconfigured, so maybe I have an invert wrong.The EC does control
DD_ONwhich controls the 3.3V and 5V rails.On page 6 of the schematics I see the U7 that forms SUSB# from SUSB#_APU (which corresponds to what you said) _and_
EC_EN, which is GPIO from IT5570, which is EC.
Quoted 6 lines
Quoted 6 lines
Quoted 1 line
Are you using different schematics? I'm using the one from FDO bug report.
Just checked this one:
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zipAlso uses EC (SUSB_EC#).
Sorry, this has to be read as SUSBC_EC#.
Quoted 2 lines
So this all makes me thing that either EC firmware is buggy or we have ACPI EC code in the kernel to fix.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Quoted 53 lines · Andy Shevchenko
Quoted 5 lines · Andy Shevchenko
Quoted 4 lines · Andy Shevchenko
Quoted 3 lines · Andy Shevchenko
Quoted 2 lines · Raul Rangel
Quoted 1 line · Werner Sembach
Am 13.02.23 um 15:37 schrieb Andy Shevchenko:
...
Quoted 43 lines
Quoted 43 lines
Quoted 43 lines
Quoted 31 lines
Quoted 30 lines
Schematics for the NH5xAx can also be found on this unofficial clevo mirror (service manuals, scroll to end for schematics):
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zip
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AF1.zip
User: repo
PW: repo
Quoted 19 lines
Quoted 5 lines
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Thank you!
I have looked at the schematics and read discussion.So, the conclusion that this is a BIOS bug is incorrect in my opinion. The problem is either in the PMIC/EC firmware that shouldn't shut down 3.3VS signal for a while or on the PCB level, so that pull up should be connected to another power source that stays on.
This means the description on the initial patch with the same issue is incorrect.
Do we know the power sequence on the suspend to see which and how on the time line the power sources are off/on?
Quoted 7 lines
If you look at the load switch for 3.3VS, its EN2 pin is connected to SUSB#_EN which is connected to SUSB# which is connected to
AND(SUSB#_PCH -> SLP_S3_L, PM_SLP_S0 -> S0A3_GPIO). So there is no PMIC/EC firmware that is incharge of this. I guess I'm not quite sure how they haveS0A3_GPIOconfigured, so maybe I have an invert wrong.The EC does control
DD_ONwhich controls the 3.3V and 5V rails.On page 6 of the schematics I see the U7 that forms SUSB# from SUSB#_APU (which corresponds to what you said) _and_
EC_EN, which is GPIO from IT5570, which is EC.
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
Quoted 1 line
Are you using different schematics? I'm using the one from FDO bug report.
Just checked this one:
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zipAlso uses EC (SUSB_EC#).
Sorry, this has to be read as SUSBC_EC#.
It looks like SUSBC_EC# has to stay high during S3/S0i3 otherwise it's going to shut down the S5 power domain. So I'm guessing U7 is there to prevent the S3 domain from being powered on while the S5 domain is powered off.
Sheet 59 of 73 VDDCR_SOC_S5, VDDCR_ALW seems to have a helpful table that describes all the power states. I'm confused where SLP_SUS# comes from though. I'm also not sure about S5_MUX_CTRL since that seems to be connected to a testpoint.
Quoted 9 lines
Quoted 3 lines
So this all makes me thing that either EC firmware is buggy or we have ACPI EC code in the kernel to fix.
--
With Best Regards,
Andy Shevchenko
Quoted 9 lines · Raul Rangel
Quoted 7 lines · Andy Shevchenko
Quoted 5 lines · Andy Shevchenko
Quoted 4 lines · Andy Shevchenko
Quoted 3 lines · Andy Shevchenko
Quoted 2 lines · Raul Rangel
Quoted 1 line · Werner Sembach
Am 13.02.23 um 15:37 schrieb Andy Shevchenko:
...
Quoted 57 lines
Quoted 43 lines
Quoted 43 lines
Quoted 43 lines
Quoted 43 lines
Quoted 31 lines
Quoted 30 lines
Schematics for the NH5xAx can also be found on this unofficial clevo mirror (service manuals, scroll to end for schematics):
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zip
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AF1.zip
User: repo
PW: repo
Quoted 19 lines
Quoted 5 lines
The schematics were shared by the reporter for the original issue which is how we reached the conclusion there was a mistake.
As they're both Clevo designs it's certainly possible they have the same mistake in two systems.
Thank you!
I have looked at the schematics and read discussion.So, the conclusion that this is a BIOS bug is incorrect in my opinion. The problem is either in the PMIC/EC firmware that shouldn't shut down 3.3VS signal for a while or on the PCB level, so that pull up should be connected to another power source that stays on.
This means the description on the initial patch with the same issue is incorrect.
Do we know the power sequence on the suspend to see which and how on the time line the power sources are off/on?
Quoted 7 lines
If you look at the load switch for 3.3VS, its EN2 pin is connected to SUSB#_EN which is connected to SUSB# which is connected to
AND(SUSB#_PCH -> SLP_S3_L, PM_SLP_S0 -> S0A3_GPIO). So there is no PMIC/EC firmware that is incharge of this. I guess I'm not quite sure how they haveS0A3_GPIOconfigured, so maybe I have an invert wrong.The EC does control
DD_ONwhich controls the 3.3V and 5V rails.On page 6 of the schematics I see the U7 that forms SUSB# from SUSB#_APU (which corresponds to what you said) _and_
EC_EN, which is GPIO from IT5570, which is EC.Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
Quoted 1 line
Are you using different schematics? I'm using the one from FDO bug report.
Just checked this one:
http://repo.palkeo.com/clevo-mirror/NH5xACx_AFx_ADx/NH50AC.zipAlso uses EC (SUSB_EC#).
Sorry, this has to be read as SUSBC_EC#.
It looks like SUSBC_EC# has to stay high during S3/S0i3 otherwise it's going to shut down the S5 power domain. So I'm guessing U7 is there to prevent the S3 domain from being powered on while the S5 domain is powered off.
Quoted 4 lines
Sheet 59 of 73
VDDCR_SOC_S5,VDDCR_ALWseems to have a helpful table that describes all the power states. I'm confused where SLP_SUS# comes from though. I'm also not sure aboutS5_MUX_CTRLsince that seems to be connected to a testpoint.
I see, thanks for looking into this.
So, if EC has no business with this, whose responsibility to assert that signal? I'm trying to get if it's PCB issue (wrong power rail for pull up) or something else.
Btw, is anybody can actually boot Windows and check the signals of the pin on a time line in comparison to Linux to see if the behaviour of them is the same? (If Windows and Linux got the same timeline of the signals it would mean that
the issue in the Linux kernel.)
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
So this all makes me thing that either EC firmware is buggy or we have ACPI EC code in the kernel to fix.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Fri, Feb 10, 2023 at 05:46:36PM +0100, Werner Sembach kirjoitti:
Quoted 11 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up. As soon as the system suspends the touchpad loses power and then the system wakes up.
To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
Please, update the commit message and send v2.
We would like to have this fix nevertheless, because users will suffer w/o it.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Am 13.02.23 um 22:56 schrieb [email protected]:
Quoted 10 lines
Fri, Feb 10, 2023 at 05:46:36PM +0100, Werner Sembach kirjoitti:
Quoted 9 lines
commit
1796f808e4bb("HID: i2c-hid: acpi: Stop settingwakeup_capable") changed the policy such that I2C touchpads may be able to wake up the system by default if the system is configured as such.However on Clevo NH5xAx/TUXEDO XA15 Gen10 there is a mistake in the ACPI tables that the TP_ATTN# signal connected to GPIO 10 is configured as ActiveLow and level triggered but connected to a pull up. As soon as the system suspends the touchpad loses power and then the system wakes up.
Quoted 6 lines
Quoted 2 lines
To avoid this problem, introduce a quirk for this model that will prevent the wakeup capability for being set for GPIO 10.
Please, update the commit message and send v2.
We would like to have this fix nevertheless, because users will suffer w/o it.
OK I'm on it.