arm64: imx: Add support for imx8mp-beacon-kit
Subsystems (3)
PATCH 1/1 arm64: imx: Add support for imx8mp-beacon-kit
Beacon Embedded has an i.MX8M Plus development kit which consists of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC, and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet PHY. The device trees are already queued for inclusion in Linux 6.3.
arch/arm/dts/Makefile +1 -0
@@ -986,6 +986,7 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mn-beacon-kit.dtb \ imx8mq-mnt-reform2.dtb \ imx8mq-phanbell.dtb \ + imx8mp-beacon-kit.dtb \ imx8mp-dhcom-pdk2.dtb \ imx8mp-evk.dtb \ imx8mp-icore-mx8mp-edimm2.2.dtb \
arch/arm/dts/imx8mp-beacon-kit-u-boot.dtsi new file +216 -0
216 lines not on this page · raw message
arch/arm/dts/imx8mp-beacon-kit.dts new file +550 -0
550 lines not on this page · raw message
arch/arm/dts/imx8mp-beacon-som.dtsi new file +416 -0
416 lines not on this page · raw message
arch/arm/mach-imx/imx8m/Kconfig +11 -0
@@ -170,6 +170,16 @@ config TARGET_IMX8MN_VENICE select GATEWORKS_SC select MISC +config TARGET_IMX8MP_BEACON + bool "imx8mm Beacon Embedded devkit" + select BINMAN + select IMX8MP + select SUPPORT_SPL + select IMX8M_LPDDR4 + select FSL_CAAM + select ARCH_MISC_INIT + select SPL_CRYPTO if SPL + config TARGET_IMX8MP_DH_DHCOM_PDK2 bool "DH electronics DHCOM Premium Developer Kit (2) i.MX8M Plus" select BINMAN
@@ -326,6 +336,7 @@ endchoice source "board/advantech/imx8mp_rsb3720a1/Kconfig" source "board/beacon/imx8mm/Kconfig" source "board/beacon/imx8mn/Kconfig" +source "board/beacon/imx8mp/Kconfig" source "board/bsh/imx8mn_smm_s2/Kconfig" source "board/cloos/imx8mm_phg/Kconfig" source "board/compulab/imx8mm-cl-iot-gate/Kconfig"
board/beacon/imx8mp/Kconfig new file +16 -0
@@ -0,0 +1,16 @@ +if TARGET_IMX8MP_BEACON + +config SYS_BOARD + default "imx8mp" + +config SYS_VENDOR + default "beacon" + +config SYS_CONFIG_NAME + default "imx8mp_beacon" + +config IMX_CONFIG + default "board/freescale/imx8mp_evk/imximage-8mp-lpddr4.cfg" + + +endif
board/beacon/imx8mp/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +i.MX8MP Beacon EmbeddedWorks Devkit +M: Adam Ford <[email protected]> +S: Maintained +F: board/beacon/imx8mp/ +F: include/configs/imx8mp_beacon.h +F: configs/imx8mp_beacon_defconfig
board/beacon/imx8mp/Makefile new file +13 -0
@@ -0,0 +1,13 @@ +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright 2022 Logic PD, Inc dba Beacon EmbeddedWorks +# + +obj-y += imx8mp_beacon.o +obj-y += ../../freescale/common/ + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o +endif
board/beacon/imx8mp/README new file +38 -0
@@ -0,0 +1,38 @@ +U-Boot for the Beacon EmbeddedWorks i.MX8M Nano Devkit + +Quick Start +=========== +- Build the ARM Trusted firmware binary +- Get ddr firmware +- Build U-Boot +- Boot + +Get and Build the ARM Trusted firmware +====================================== +Note: $(srctree) is U-Boot source directory + +$ git clone https://source.codeaurora.org/external/imx/imx-atf +$ git lf-5.15.32-2.0.0 +$ make PLAT=imx8mp bl31 CROSS_COMPILE=aarch64-linux-gnu- +$ cp build/imx8mn/release/bl31.bin $(srctree) + +Get the DDR firmware +==================== +$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.15.bin +$ chmod +x firmware-imx-8.15.bin +$ ./firmware-imx-8.15 +$ cp firmware-imx-8.15/firmware/ddr/synopsys/lpddr4*.bin $(srctree) + +Build U-Boot +============ +$ make imx8mp_beacon_defconfig +$ make CROSS_COMPILE=aarch64-linux-gnu- + +Burn U-Boot to microSD Card +=========================== +$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32 + +Boot +==== +Set baseboard DIP switch: +S17: 1100XXXX
board/beacon/imx8mp/imx8mp_beacon.c new file +63 -0
63 lines not on this page · raw message
board/beacon/imx8mp/imximage-8mp-lpddr4.cfg new file +9 -0
@@ -0,0 +1,9 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2021 NXP + */ + + +ROM_VERSION v2 +BOOT_FROM sd +LOADER u-boot-spl-ddr.bin 0x920000
board/beacon/imx8mp/lpddr4_timing.c new file +1881 -0
1,643 lines not on this page · raw message
board/beacon/imx8mp/spl.c new file +132 -0
132 lines not on this page · raw message
configs/imx8mp_beacon_defconfig new file +171 -0
171 lines not on this page · raw message
include/configs/imx8mp_beacon.h new file +85 -0
85 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.34.1
Part of the diff is not shown here. View the raw message.
Quoted 7 lines · Adam Ford
Beacon Embedded has an i.MX8M Plus development kit which consists of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC, and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by Adam Ford <[email protected]>
[snip]
board/beacon/imx8mp/README
Quoted 5 lines
board/beacon/imx8mp/README new file +0
-0
Our rST docs have gotten to the point I think where we should say no to new board README files, this belongs under doc/board/
[snip]
Quoted 42 lines
board/beacon/imx8mp/README new file +42
-0+#define CFG_EXTRA_ENV_SETTINGS \ + "scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ + "kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ + "image=Image\0" \ + "console=ttymxc1,115200\0" \ + "fdt_addr_r=0x43000000\0" \ + "fdt_addr=0x43000000\0" \ + "boot_fdt=try\0" \ + "boot_fit=no\0" \ + "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ + "bootm_size=0x10000000\0" \ + "mmcdev=1\0" \ + "mmcpart=1\0" \ + "optargs=audit=0 video=LVDS-1:d video=LVDS-2:d\0" \ + "finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \ + "mmcargs=setenv bootargs console=${console} " \ + " root=PARTUUID=${uuid} rootwait rw ${mtdparts} ${optargs}\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=echo ${fdt_file}; fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run finduuid; run mmcargs; " \ + "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ + "bootm ${loadaddr}; " \ + "else " \ + "if run loadfdt; then " \ + "booti ${loadaddr} - ${fdt_addr_r}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi;\0" \ + "netargs=setenv bootargs ${jh_clk} console=${console} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \
board/beacon/imx8mp/README
Quoted 10 lines
board/beacon/imx8mp/README new file +10
-0+ "${get_cmd} ${loadaddr} ${image}; " \ + "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ + "bootm ${loadaddr}; " \ + "else " \ + "if ${get_cmd} ${fdt_addr_r} ${fdt_file}; then " \ + "booti ${loadaddr} - ${fdt_addr_r}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi;\0"
And this should all be plain text environment (see board/*/*/*.env for examples), and please put it somewhere on your TODO list to migrate other platforms README and environments, thanks!
Signature · 1 line
Tom
Quoted 11 lines · Tom Rini
Quoted 7 lines · Adam Ford
Beacon Embedded has an i.MX8M Plus development kit which consists of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC, and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by Adam Ford <[email protected]>[snip]
Quoted 8 lines
board/beacon/imx8mp/README
Quoted 5 lines
board/beacon/imx8mp/README new file +0
-0Our rST docs have gotten to the point I think where we should say no to new board README files, this belongs under doc/board/
OK. I'll work on that.
Quoted 55 lines
[snip]
Quoted 42 lines
board/beacon/imx8mp/README new file +42
-0+#define CFG_EXTRA_ENV_SETTINGS \ + "scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ + "kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ + "image=Image\0" \ + "console=ttymxc1,115200\0" \ + "fdt_addr_r=0x43000000\0" \ + "fdt_addr=0x43000000\0" \ + "boot_fdt=try\0" \ + "boot_fit=no\0" \ + "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ + "bootm_size=0x10000000\0" \ + "mmcdev=1\0" \ + "mmcpart=1\0" \ + "optargs=audit=0 video=LVDS-1:d video=LVDS-2:d\0" \ + "finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \ + "mmcargs=setenv bootargs console=${console} " \ + " root=PARTUUID=${uuid} rootwait rw ${mtdparts} ${optargs}\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=echo ${fdt_file}; fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run finduuid; run mmcargs; " \ + "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ + "bootm ${loadaddr}; " \ + "else " \ + "if run loadfdt; then " \ + "booti ${loadaddr} - ${fdt_addr_r}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi;\0" \ + "netargs=setenv bootargs ${jh_clk} console=${console} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \board/beacon/imx8mp/README
Quoted 10 lines
board/beacon/imx8mp/README new file +10
-0+ "${get_cmd} ${loadaddr} ${image}; " \ + "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ + "bootm ${loadaddr}; " \ + "else " \ + "if ${get_cmd} ${fdt_addr_r} ${fdt_file}; then " \ + "booti ${loadaddr} - ${fdt_addr_r}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi;\0"
Quoted 1 line
And this should all be plain text environment (see board/*/*/*.env for
I didn't even know this was a thing, but after reviewing what others are doing, I like this much better.
Quoted 2 lines
examples), and please put it somewhere on your TODO list to migrate other platforms README and environments, thanks!
Is there a deadline?
thanks
adam
Quoted 3 lines
--
Tom
Quoted 78 lines · Adam Ford
Quoted 11 lines · Tom Rini
Quoted 7 lines · Adam Ford
Beacon Embedded has an i.MX8M Plus development kit which consists of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC, and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by Adam Ford <[email protected]>[snip]
Quoted 8 lines
board/beacon/imx8mp/README
Quoted 5 lines
board/beacon/imx8mp/README new file +0
-0Our rST docs have gotten to the point I think where we should say no to new board README files, this belongs under doc/board/
OK. I'll work on that.
Quoted 55 lines
[snip]
Quoted 52 lines
board/beacon/imx8mp/README new file +52
-0+#define CFG_EXTRA_ENV_SETTINGS \ + "scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ + "kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ + "image=Image\0" \ + "console=ttymxc1,115200\0" \ + "fdt_addr_r=0x43000000\0" \ + "fdt_addr=0x43000000\0" \ + "boot_fdt=try\0" \ + "boot_fit=no\0" \ + "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ + "bootm_size=0x10000000\0" \ + "mmcdev=1\0" \ + "mmcpart=1\0" \ + "optargs=audit=0 video=LVDS-1:d video=LVDS-2:d\0" \ + "finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \ + "mmcargs=setenv bootargs console=${console} " \ + " root=PARTUUID=${uuid} rootwait rw ${mtdparts} ${optargs}\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=echo ${fdt_file}; fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run finduuid; run mmcargs; " \ + "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ + "bootm ${loadaddr}; " \ + "else " \ + "if run loadfdt; then " \ + "booti ${loadaddr} - ${fdt_addr_r}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi;\0" \ + "netargs=setenv bootargs ${jh_clk} console=${console} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${loadaddr} ${image}; " \ + "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ + "bootm ${loadaddr}; " \ + "else " \ + "if ${get_cmd} ${fdt_addr_r} ${fdt_file}; then " \ + "booti ${loadaddr} - ${fdt_addr_r}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi;\0"
Quoted 4 lines
Quoted 1 line
And this should all be plain text environment (see board/*/*/*.env for
I didn't even know this was a thing, but after reviewing what others are doing, I like this much better.
That's good to hear.
Quoted 4 lines
Quoted 2 lines
examples), and please put it somewhere on your TODO list to migrate other platforms README and environments, thanks!
Is there a deadline?
Neither has a firm deadline at this point, thanks!
Signature · 1 line
Tom
Quoted 85 lines · Tom Rini
Quoted 78 lines · Adam Ford
Quoted 11 lines · Tom Rini
Quoted 7 lines · Adam Ford
Beacon Embedded has an i.MX8M Plus development kit which consists of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC, and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by Adam Ford <[email protected]>[snip]
Quoted 8 lines
board/beacon/imx8mp/README
Quoted 5 lines
board/beacon/imx8mp/README new file +0
-0Our rST docs have gotten to the point I think where we should say no to new board README files, this belongs under doc/board/
OK. I'll work on that.
Quoted 55 lines
[snip]
Quoted 52 lines
board/beacon/imx8mp/README new file +52
-0+#define CFG_EXTRA_ENV_SETTINGS \ + "scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ + "kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ + "image=Image\0" \ + "console=ttymxc1,115200\0" \ + "fdt_addr_r=0x43000000\0" \ + "fdt_addr=0x43000000\0" \ + "boot_fdt=try\0" \ + "boot_fit=no\0" \ + "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ + "bootm_size=0x10000000\0" \ + "mmcdev=1\0" \ + "mmcpart=1\0" \ + "optargs=audit=0 video=LVDS-1:d video=LVDS-2:d\0" \ + "finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \ + "mmcargs=setenv bootargs console=${console} " \ + " root=PARTUUID=${uuid} rootwait rw ${mtdparts} ${optargs}\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=echo ${fdt_file}; fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run finduuid; run mmcargs; " \ + "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ + "bootm ${loadaddr}; " \ + "else " \ + "if run loadfdt; then " \ + "booti ${loadaddr} - ${fdt_addr_r}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi;\0" \ + "netargs=setenv bootargs ${jh_clk} console=${console} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${loadaddr} ${image}; " \ + "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ + "bootm ${loadaddr}; " \ + "else " \ + "if ${get_cmd} ${fdt_addr_r} ${fdt_file}; then " \ + "booti ${loadaddr} - ${fdt_addr_r}; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi;\0"Quoted 4 lines
Quoted 1 line
And this should all be plain text environment (see board/*/*/*.env for
I didn't even know this was a thing, but after reviewing what others are doing, I like this much better.
Quoted 8 lines
That's good to hear.
Quoted 4 lines
Quoted 2 lines
examples), and please put it somewhere on your TODO list to migrate other platforms README and environments, thanks!
Is there a deadline?
Neither has a firm deadline at this point, thanks!
Tom,
I pushed a V2 and CC'd you. If you're OK with both the env file and the rst file for this board, I'll do the same thing for the other Beacon and LogicPD boards. I just don't want to do the work until I know my first attempt at these new files is acceptable.
Thanks,
adam
Quoted 3 lines
--
Tom