Skip to contentSkip to conversation

arm:dts: am3517-evm: Fix LED3/4 pinmux

PATCH Superseded Adam Ford 2 participants 3 messages Sep 8, 2023 – Sep 10, 2023

Subsystems (2)
Device tree bindings OMAP device tree support

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH v2 1/2 arm:dts: am3517-evm: Fix LED3/4 pinmux

The pinmux for LED3 and LED4 are incorrectly attached to the omap3_pmx_core when they should be connected to the omap3_pmx_wkup pin mux. This was likely masked by the fact that the bootloader used to do all the pinmuxing.

Fixes 0dbf99542caf ("ARM: dts: am3517-evm: Add User LEDs and Pushbutton")
Signed-off-by Adam Ford <[email protected]>

---

V2: Use current device tree naming convention for led-pins

This likely will require a separate patch to apply to previous file location.

arch/arm/boot/dts/ti/omap/am3517-evm.dts +9 -7
index af9df15274be..866f68c5b504 100644
@@ -271,13 +271,6 @@ OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c3_sda */
 		>;
 	};
 
-	leds_pins: leds-pins {
-		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 */
-			OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu1.gpio_31 */
-		>;
-	};
-
 	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */

@@ -355,3 +348,12 @@ OMAP3430_CORE2_IOPAD(0x25e2, PIN_INPUT | MUX_MODE3)	/* etk_d3.hsusb1_data7 */
 		>;
 	};
 };
+
+&omap3_pmx_wkup {
+	leds_pins: leds-pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 */
+			OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu1.gpio_31 */
+		>;
+	};
+};
Signature · 1 line
2.39.2
author
#1 lore raw

PATCH v2 2/2 arm: dts: am3517-evm: Enable Ethernet PHY Interrupt

The Ethernet PHY interrupt pin is routed to GPIO_58. Create a PHY node to configure this GPIO for the interrupt to avoid polling.

Signed-off-by Adam Ford <[email protected]>

---
V2: Use current device tree naming convention for led-pins

arch/arm/boot/dts/ti/omap/am3517-evm.dts +19 -0
index 866f68c5b504..8a3d850a4f0d 100644
@@ -172,11 +172,24 @@ hsusb1_phy: hsusb1_phy {
 &davinci_emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
 	status = "okay";
 };
 
 &davinci_mdio {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&enet_phy_pins>;
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;	/* gpio_58 */
+	};
 };
 
 &dss {

@@ -257,6 +270,12 @@ OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50mhz_clk */
 		>;
 	};
 
+	enet_phy_pins: pinmux_ent_phy_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20bc, PIN_INPUT | MUX_MODE4)	/* gpmc_ncs7.gpio_57 */
+		>;
+	};
+
 	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c2_scl */
Signature · 1 line
2.39.2
#2 lore raw

Re: [PATCH V2 2/2] arm: dts: am3517-evm: Enable Ethernet PHY Interrupt

Quoted 37 lines · Adam Ford

The Ethernet PHY interrupt pin is routed to GPIO_58. Create a PHY node to configure this GPIO for the interrupt to avoid polling.

Signed-off-by Adam Ford <[email protected]>

---
V2: Use current device tree naming convention for led-pins

arch/arm/boot/dts/ti/omap/am3517-evm.dts +13 -0
index 866f68c5b504..8a3d850a4f0d 100644
@@ -172,11 +172,24 @@ hsusb1_phy: hsusb1_phy {
 &davinci_emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
 	status = "okay";
 };
 
 &davinci_mdio {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&enet_phy_pins>;
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;	/* gpio_58 */
+	};
 };
 
 &dss {

arch/arm/boot/dts/ti/omap/am3517-evm.dts OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50mhz_clk */ · line 273

Quoted 4 lines
arch/arm/boot/dts/ti/omap/am3517-evm.dts +1 -0
@@ -257,6 +270,12 @@ OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50mhz_clk */
 		>;
 	};
 
+	enet_phy_pins: pinmux_ent_phy_pins {

No improvements...

Best regards,
Krzysztof