spi: bcm2835: add a sentinel at the end of the lookup array
Subsystems (4)
PATCH 1/1 spi: bcm2835: add a sentinel at the end of the lookup array
From: Bartosz Golaszewski <[email protected]>
GPIOLIB expects the array of lookup entries to be terminated with an empty member. We need to increase the size of the variable length array in the lookup table by 1.
--- drivers/spi/spi-bcm2835.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-bcm2835.c +1 -1
@@ -1299,7 +1299,7 @@ static int bcm2835_spi_setup(struct spi_device *spi)* More on the problem that it addresses: * https://www.spinics.net/lists/linux-gpio/msg36218.html */ - lookup =kzalloc (struct_size (lookup, table,1 ),GFP_KERNEL ); + lookup =kzalloc (struct_size (lookup, table,2 ),GFP_KERNEL );if (!lookup) { ret = -ENOMEM ; goto err_cleanup;
Signature · 1 line
2.39.2
Quoted 5 lines · Bartosz Golaszewski
From: Bartosz Golaszewski <[email protected]>
GPIOLIB expects the array of lookup entries to be terminated with an empty member. We need to increase the size of the variable length array in the lookup table by 1.
Right and seems we (used to?) have the same mistake spread over the kernel. Perhaps a helper at some point?
Signature · 9 lines
With Best Regards, Andy Shevchenko _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 9 lines · Andy Shevchenko
Quoted 5 lines · Bartosz Golaszewski
From: Bartosz Golaszewski <[email protected]>
GPIOLIB expects the array of lookup entries to be terminated with an empty member. We need to increase the size of the variable length array in the lookup table by 1.
Right and seems we (used to?) have the same mistake spread over the kernel.
Almost all lookup tables are static and have a sentinel appended. The temporary lookup hack is only used here and in the int3472 driver AFAIK so it's not that bad.
Quoted 2 lines
Perhaps a helper at some point?
I don't want to make it a habit for people. This is still a hack, just less bad than what was here before. So I don't think we need a helper here.
Bart
Quoted 7 lines
Reviewed-by Andy Shevchenko <[email protected]>--
With Best Regards,
Andy Shevchenko
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 10 lines · Bartosz Golaszewski
From: Bartosz Golaszewski <[email protected]>
GPIOLIB expects the array of lookup entries to be terminated with an empty member. We need to increase the size of the variable length array in the lookup table by 1.
Fixes 21f252cd29f0 ("spi: bcm2835: reduce the abuse of the GPIO API")Reported-by Hans de Goede <[email protected]>Signed-off-by Bartosz Golaszewski <[email protected]>
OK my bad (I think?)
Yours,
Linus Walleij
Mark Brown
maintainerQuoted 5 lines · Bartosz Golaszewski
GPIOLIB expects the array of lookup entries to be terminated with an empty member. We need to increase the size of the variable length array in the lookup table by 1.
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
Thanks!
[1/1] spi: bcm2835: add a sentinel at the end of the lookup array
commit: 9aaa25df9b02bfe5579cbc9b4cc1177c662ec33f
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Quoted 30 lines · Mark Brown
Quoted 5 lines · Bartosz Golaszewski
GPIOLIB expects the array of lookup entries to be terminated with an empty member. We need to increase the size of the variable length array in the lookup table by 1.
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
Thanks!
[1/1] spi: bcm2835: add a sentinel at the end of the lookup array
commit: 9aaa25df9b02bfe5579cbc9b4cc1177c662ec33fAll being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Quoted 6 lines
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Mark,
Can you provide me with an immutable branch containing commit 21f252cd29f08892d48739fd7513ad79c1cff96a (the one this one fixes)?
We are very close to removing gpiochip_find() from the GPIOLIB and with this pulled we could remove it for v6.7.
Bart
Mark Brown
maintainerQuoted 11 lines · Bartosz Golaszewski
Quoted 4 lines · Mark Brown
On Wed, 04 Oct 2023 20:39:06 +0200, Bartosz Golaszewski wrote:
[1/1] spi: bcm2835: add a sentinel at the end of the lookup array
commit: 9aaa25df9b02bfe5579cbc9b4cc1177c662ec33fCan you provide me with an immutable branch containing commit
21f252cd29f08892d48739fd7513ad79c1cff96a(the one this one fixes)?We are very close to removing
gpiochip_find()from the GPIOLIB and with this pulled we could remove it for v6.7.
Ugh, *please* say this sort of thing when sending patches rather than waiting until after they've been applied. The default is just to add patches to the normal development branches which means they have the whole history for the release cycle after them and may well have other things applied on top of them before you get round to asking for them to be applied on a different branch as is the case here.
Quoted 14 lines · Mark Brown
Quoted 11 lines · Bartosz Golaszewski
Quoted 4 lines · Mark Brown
On Wed, 04 Oct 2023 20:39:06 +0200, Bartosz Golaszewski wrote:
[1/1] spi: bcm2835: add a sentinel at the end of the lookup array
commit: 9aaa25df9b02bfe5579cbc9b4cc1177c662ec33fCan you provide me with an immutable branch containing commit
21f252cd29f08892d48739fd7513ad79c1cff96a(the one this one fixes)?We are very close to removing
gpiochip_find()from the GPIOLIB and with this pulled we could remove it for v6.7.
Quoted 6 lines
Ugh, *please* say this sort of thing when sending patches rather than waiting until after they've been applied. The default is just to add patches to the normal development branches which means they have the whole history for the release cycle after them and may well have other things applied on top of them before you get round to asking for them to be applied on a different branch as is the case here.
I'm sorry. I didn't expect the removal process to go as fast as there were quite a few users but it turned out to be almost ready now.
We can wait until rc7 when your for-next branch will be more or less immutable and then you can tag 21f252cd29f08892d48739fd7513ad79c1cff96a alone (it only has a few commits between it and v6.6-rc1) if that works for you?
Bart
Mark Brown
maintainerQuoted 5 lines · Bartosz Golaszewski
GPIOLIB expects the array of lookup entries to be terminated with an empty member. We need to increase the size of the variable length array in the lookup table by 1.
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
Thanks!
[1/1] spi: bcm2835: add a sentinel at the end of the lookup array
commit: 9aaa25df9b02bfe5579cbc9b4cc1177c662ec33f
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Quoted 26 lines · Bartosz Golaszewski
Quoted 14 lines · Mark Brown
Quoted 11 lines · Bartosz Golaszewski
Quoted 4 lines · Mark Brown
On Wed, 04 Oct 2023 20:39:06 +0200, Bartosz Golaszewski wrote:
[1/1] spi: bcm2835: add a sentinel at the end of the lookup array
commit: 9aaa25df9b02bfe5579cbc9b4cc1177c662ec33fCan you provide me with an immutable branch containing commit
21f252cd29f08892d48739fd7513ad79c1cff96a(the one this one fixes)?We are very close to removing
gpiochip_find()from the GPIOLIB and with this pulled we could remove it for v6.7.Quoted 6 lines
Ugh, *please* say this sort of thing when sending patches rather than waiting until after they've been applied. The default is just to add patches to the normal development branches which means they have the whole history for the release cycle after them and may well have other things applied on top of them before you get round to asking for them to be applied on a different branch as is the case here.
I'm sorry. I didn't expect the removal process to go as fast as there were quite a few users but it turned out to be almost ready now.
Quoted 6 lines
We can wait until rc7 when your for-next branch will be more or less immutable and then you can tag
21f252cd29f08892d48739fd7513ad79c1cff96aalone (it only has a few commits between it and v6.6-rc1) if that works for you?Bart
Alternatively - if you send your SPI PR to Linus early in the merge window, I will send the patch removing gpiochip_find() later on top of it?
Bart
Mark Brown
maintainerQuoted 9 lines · Bartosz Golaszewski
Quoted 7 lines · Bartosz Golaszewski
I'm sorry. I didn't expect the removal process to go as fast as there were quite a few users but it turned out to be almost ready now.
We can wait until rc7 when your for-next branch will be more or less immutable and then you can tag
21f252cd29f08892d48739fd7513ad79c1cff96aalone (it only has a few commits between it and v6.6-rc1) if that works for you?
I spent some time yesterday looking at pulling out a branch but there's other dependencies way back in the history so that's probably not going to work well.
Quoted 3 lines
Alternatively - if you send your SPI PR to Linus early in the merge window, I will send the patch removing
gpiochip_find()later on top of it?
I tend to send all my PRs the morning the merge window opens so that'd not be a problem. If I send you a PR at -rc7 you'd realistically want to wait until that was merged before sending yours anyway.
Mark Brown
maintainerQuoted 3 lines · Bartosz Golaszewski
Alternatively - if you send your SPI PR to Linus early in the merge window, I will send the patch removing
gpiochip_find()later on top of it?
The following changes since commit 0bb80ecc33a8fb5a682236443c1e740d5c917d1d:
Linux 6.6-rc1 (2023-09-10 16:28:41 -0700)
are available in the Git repository at:
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git tags/spi-bcm2835-sentinel
for you to fetch changes up to 9aaa25df9b02bfe5579cbc9b4cc1177c662ec33f:
spi: bcm2835: add a sentinel at the end of the lookup array (2023-10-10 13:12:11 +0100)
----------------------------------------------------------------
spi: Share current state with GPIO tree
This is the current state of the SPI tree, shared with the GPIO tree in order to facilitate some treewide improvements there. Unfortunaetly the desire for this treewide work was realised after all the SPI patches had been applied and there were further dependencies with similar issues that caused issues trying to pull things out into a minimal branch.
It's expected that this will be merged into Linus' tree as part of the full SPI pull request before the GPIO changes go in.
----------------------------------------------------------------
Andy Shevchenko (3):
spidev: Decrease indentation level in spidev_ioctl() SPI_IOC_RD_MODE*
spidev: Switch to use spi_get_csgpiod()
spidev: Simplify SPI_IOC_RD_MODE* cases in spidev_ioctl()
Bartosz Golaszewski (2):
spi: bcm2835: reduce the abuse of the GPIO API
spi: bcm2835: add a sentinel at the end of the lookup array
Christophe JAILLET (1):
spi: at91-usart: Remove some dead code
Dhruva Gole (2):
spi: spi-cadence-quadspi: add runtime pm support
spi: spi-cadence-quadspi: Fix missing unwind goto warnings
Geert Uytterhoeven (1):
spi: mpc52xx-psc: Make mpc52xx_psc_spi_transfer_one_message() static
Greg Kroah-Hartman (1):
spi: spidev: make spidev_class constant
Kees Cook (1):
spi: mchp-pci1xxxx: Annotate struct pci1xxxx_spi with __counted_by
Li Zetao (25):
spi: ar934x: Use helper function devm_clk_get_enabled()
spi: armada-3700: Use helper function devm_clk_get_prepared()
spi: aspeed: Use helper function devm_clk_get_enabled()
spi: ath79: Use helper function devm_clk_get_enabled()
spi: spi-axi-spi-engine: Use helper function devm_clk_get_enabled()
spi: bcm2835: Use helper function devm_clk_get_enabled()
spi: bcm2835aux: Use helper function devm_clk_get_enabled()
spi: spi-cadence: Use helper function devm_clk_get_enabled()
spi: spi-cavium-thunderx: Use helper function devm_clk_get_enabled()
spi: davinci: Use helper function devm_clk_get_enabled()
spi: dw-bt1: Use helper function devm_clk_get_enabled()
spi: dw-mmio: Use helper function devm_clk_get_*()
spi: spi-fsl-dspi: Use helper function devm_clk_get_enabled()
spi: lantiq-ssc: Use helper function devm_clk_get_enabled()
spi: meson-spicc: Use helper function devm_clk_get_enabled()
spi: spi-meson-spifc: Use helper function devm_clk_get_enabled()
spi: microchip-core-qspi: Use helper function devm_clk_get_enabled()
spi: microchip-core: Use helper function devm_clk_get_enabled()
spi: mtk-snfi: Use helper function devm_clk_get_enabled()
spi: npcm-fiu: Use helper function devm_clk_get_enabled()
spi: orion: Use helper function devm_clk_get_enabled()
spi: pic32-sqi: Use helper function devm_clk_get_enabled()
spi: pic32: Use helper function devm_clk_get_enabled()
spi: spl022: Use helper function devm_clk_get_enabled()
spi: rockchip: Use helper function devm_clk_get_enabled()
Mark Brown (6):
spi: sun6i: fix RX data corruption in DMA mode Merge existing fixes from spi/for-6.6 into new branch
spidev: A few cleanups
spi: switch to use modern name (part3)
spi: Use devm_clk_get_*() helper function to
spi: qup: Allow scaling power domains and
Rob Herring (3):
spi: dt-bindings: arm,pl022: Move child node properties to separate schema
spi: dt-bindings: st,stm32-spi: Move "st,spi-midi-ns" to spi-peripheral-props.yaml
spi: dt-bindings: Make "additionalProperties: true" explicit
Stephan Gerhold (4):
spi: dt-bindings: qup: Document power-domains and OPP
spi: qup: Parse OPP table for DVFS support
spi: dt-bindings: qup: Document interconnects
spi: qup: Vote for interconnect bandwidth to DRAM
Uwe Kleine-König (1):
spi: Drop warning from spi_stop_queue()
Vaishnav Achath (1):
spi: omap2-mcspi: Fix hardcoded reference clock
Vijaya Krishna Nivarthi (1):
spi: spi-geni-qcom: Rename the label unmap_if_dma
Yang Yingliang (21):
spi: lm70llp: switch to use modern name
spi: lp-8841: switch to use modern name
spi: meson-spicc: switch to use modern name
spi: meson-spifc: switch to use modern name
spi: microchip-core-qspi: switch to use modern name
spi: microchip-core: switch to use modern name
spi: mpc512x-psc: switch to use modern name
spi: mpc52xx-psc: switch to use modern name
spi: mpc52xx: switch to use modern name
spi: mt65xx: switch to use modern name
spi: mt7621: switch to use modern name
spi: mtk-nor: switch to use modern name
spi: mtk-snfi: switch to use modern name
spi: mux: switch to use spi_alloc_host()
spi: mxic: switch to use modern name
spi: mxs: switch to use modern name
spi: npcm-pspi: switch to use modern name
spi: nxp-fspi: switch to use modern name
spi: oc-tiny: switch to use modern name
spi: omap-uwire: switch to use modern name
spi: omap2-mcspi: switch to use modern name
Zhang Shurong (1):
spi: tegra: Fix missing IRQ check in tegra_slink_probe()
.../bindings/spi/allwinner,sun4i-a10-spi.yaml | 2 + .../bindings/spi/allwinner,sun6i-a31-spi.yaml | 2 + .../bindings/spi/arm,pl022-peripheral-props.yaml | 61 +++++ .../bindings/spi/nvidia,tegra210-quad.yaml | 1 + .../devicetree/bindings/spi/qcom,spi-qup.yaml | 13 + .../devicetree/bindings/spi/rockchip-sfc.yaml | 2 + .../devicetree/bindings/spi/snps,dw-apb-ssi.yaml | 2 + .../bindings/spi/spi-peripheral-props.yaml | 6 + .../devicetree/bindings/spi/spi-pl022.yaml | 51 ---- .../devicetree/bindings/spi/st,stm32-spi.yaml | 20 -- drivers/spi/spi-ar934x.c | 22 +- drivers/spi/spi-armada-3700.c | 23 +- drivers/spi/spi-aspeed-smc.c | 16 +- drivers/spi/spi-at91-usart.c | 22 +- drivers/spi/spi-ath79.c | 11 +- drivers/spi/spi-axi-spi-engine.c | 25 +- drivers/spi/spi-bcm2835.c | 69 +++--- drivers/spi/spi-bcm2835aux.c | 23 +- drivers/spi/spi-cadence-quadspi.c | 45 +++- drivers/spi/spi-cadence.c | 23 +- drivers/spi/spi-cavium-thunderx.c | 8 +- drivers/spi/spi-davinci.c | 11 +- drivers/spi/spi-dw-bt1.c | 23 +- drivers/spi/spi-dw-mmio.c | 31 +-- drivers/spi/spi-fsl-dspi.c | 12 +- drivers/spi/spi-geni-qcom.c | 6 +- drivers/spi/spi-lantiq-ssc.c | 10 +- drivers/spi/spi-lm70llp.c | 20 +- drivers/spi/spi-lp8841-rtc.c | 56 ++--- drivers/spi/spi-meson-spicc.c | 121 ++++------ drivers/spi/spi-meson-spifc.c | 79 +++---- drivers/spi/spi-microchip-core-qspi.c | 39 +-- drivers/spi/spi-microchip-core.c | 83 +++---- drivers/spi/spi-mpc512x-psc.c | 54 ++--- drivers/spi/spi-mpc52xx-psc.c | 38 +-- drivers/spi/spi-mpc52xx.c | 56 ++--- drivers/spi/spi-mt65xx.c | 190 +++++++-------- drivers/spi/spi-mt7621.c | 50 ++-- drivers/spi/spi-mtk-nor.c | 14 +- drivers/spi/spi-mtk-snfi.c | 67 +----- drivers/spi/spi-mux.c | 2 +- drivers/spi/spi-mxic.c | 68 +++--- drivers/spi/spi-mxs.c | 70 +++--- drivers/spi/spi-npcm-fiu.c | 14 +- drivers/spi/spi-npcm-pspi.c | 68 +++--- drivers/spi/spi-nxp-fspi.c | 30 +-- drivers/spi/spi-oc-tiny.c | 30 +-- drivers/spi/spi-omap-uwire.c | 32 +-- drivers/spi/spi-omap2-mcspi.c | 263 +++++++++++---------- drivers/spi/spi-orion.c | 11 +- drivers/spi/spi-pci1xxxx.c | 2 +- drivers/spi/spi-pic32-sqi.c | 27 +-- drivers/spi/spi-pic32.c | 8 +- drivers/spi/spi-pl022.c | 11 +- drivers/spi/spi-qup.c | 50 +++- drivers/spi/spi-rockchip.c | 30 +-- drivers/spi/spi-tegra20-slink.c | 2 + drivers/spi/spi.c | 4 - drivers/spi/spidev.c | 42 ++-- 59 files changed, 969 insertions(+), 1202 deletions(-) create mode 100644 Documentation/devicetree/bindings/spi/arm,pl022-peripheral-props.yaml