Move video memory reservation for SPL at the end of RAM
Subsystems (3)
cover Move video memory reservation for SPL at the end of RAM
Move video memory reservation for SPL at end of RAM so that it does not interefere with reservations for next stage so that the next stage need not have holes in between for passed regions and instead it can maintain continuity in reservations.
Also catch the bloblist before starting reservations to avoid the same problem.
While at it, also fill missing fields in video handoff struct before passing it to next stage.
This is as per discussions at :
For moving SPL framebuffer reservation at end of RAM:
https://lore.kernel.org/all/CAPnjgZ3xSoe_G3yrqwuAvoiVjUfZ+YQgkOR0ZTVXGT9VK8TwJg@mail.gmail.com/
For filling missing video handoff fields :
https://lore.kernel.org/all/CAPnjgZ1Hs0rNf0JDirp6YPsOQ5=QqQSP9g9qRwLoOASUV8a4cw@mail.gmail.com/ *** SUBJECT HERE ***
Devarsh Thakkar (5):
arm: mach-k3: common: Reserve video memory from end of the RAM
board: ti: am62x: evm: Remove video_setup from spl_board_init common/board_f: Catch bloblist before starting resevatinos
video: Skip framebuffer reservation if already reserved
video: Fill video handoff in video post probe
arch/arm/mach-k3/common.c | 21 +++++++++++++++++++++ board/ti/am62x/evm.c | 18 ------------------ common/board_f.c | 36 +++++++++++++++++++++++++++++++++--- drivers/video/video-uclass.c | 33 +++++++++++++++++++++++---------- 4 files changed, 77 insertions(+), 31 deletions(-)
Signature · 1 line
2.34.1
RFC PATCH 1/5 arm: mach-k3: common: Reserve video memory from end of the RAM
Move the function to setup video memory before page table reservation so that framebuffer memory gets reserved from the end of RAM.
This is as per the new policy being discussed for passing blobs where each of the reserved areas for bloblists to be passed need to be reserved at the end of RAM.
This is to enable the next stage to directly skip the pre-reserved area from previous stage without having to making any gaps/holes to accomodate those regions which was the case if previous stage reserved region say somewhere in the middle and not at the end of RAM.
--- arch/arm/mach-k3/common.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)
arch/arm/mach-k3/common.c +21 -0
@@ -27,6 +27,7 @@#include <env.h> #include <elf.h> #include <soc.h> +#include <video.h> #if IS_ENABLED (CONFIG_SYS_K3_SPL_ATF ) enum {
@@ -522,6 +523,24 @@ void remove_fwl_configs(struct fwl_data *fwl_data, size_t fwl_data_size) } } +static int video_setup (void ) +{ +if (CONFIG_IS_ENABLED (VIDEO )) { +ulong addr; +int ret; + + addr = gd->relocaddr; + ret =video_reserve (&addr); +if (ret) +return ret; +debug ("Reserving %luk for video at: %08lx\n" , + ((unsigned long )gd->relocaddr - addr) >>10 , addr); + gd->relocaddr = addr; + } + +return 0 ; +} +void spl_enable_dcache (void ) {#if !(defined(CONFIG_SYS_ICACHE_OFF ) && defined(CONFIG_SYS_DCACHE_OFF ))
@@ -537,6 +556,8 @@ void spl_enable_dcache(void)if (ram_top >=0x100000000 ) ram_top = (phys_addr_t )0x100000000 ; + gd->relocaddr = ram_top; +video_setup (); gd->arch.tlb_addr = ram_top - gd->arch.tlb_size; gd->arch.tlb_addr &= ~(0x10000 -1 ); debug("TLB table from %08lx to %08lx\n", gd->arch.tlb_addr,
Signature · 1 line
2.34.1
RFC PATCH 2/5 board: ti: am62x: evm: Remove video_setup from spl_board_init
In reply to Devarsh ThakkarRemove video_setup from evm_init sequence since it is now getting called at an earlier place now to make sure video memory is reserved at the end of RAM.
--- board/ti/am62x/evm.c | 18 ------------------ 1 file changed, 18 deletions(-)
board/ti/am62x/evm.c +0 -18
@@ -60,27 +60,9 @@ int dram_init_banksize(void) }#if defined(CONFIG_SPL_BUILD ) -static int video_setup (void ) -{ -if (CONFIG_IS_ENABLED (VIDEO )) { -ulong addr; -int ret; - - addr = gd->relocaddr; - ret =video_reserve (&addr); -if (ret) -return ret; -debug ("Reserving %luk for video at: %08lx\n" , - ((unsigned long )gd->relocaddr - addr) >>10 , addr); - gd->relocaddr = addr; - } - -return 0 ; -}void spl_board_init (void ) { -video_setup ();enable_caches ();if (IS_ENABLED (CONFIG_SPL_SPLASH_SCREEN ) &&IS_ENABLED (CONFIG_SPL_BMP ))splash_display ();
Signature · 1 line
2.34.1
RFC PATCH 3/5 common/board_f: Catch bloblist before starting resevatinos
In reply to Devarsh ThakkarStart reservations needed for init sequence only after catching bloblists from previous stage.
This is to avoid catching bloblists in the middle causing gaps while u-boot is reserving.
Adjust the relocaddr as per video hand-off information received from previous stage so that further reservations start only after regions reserved for previous stages
Skip reservation for video memory if it was already filled by a bloblist.
--- common/board_f.c | 36 +++++++++++++++++++++++++++++++++--- 1 file changed, 33 insertions(+), 3 deletions(-)
common/board_f.c +33 -3
@@ -403,7 +403,8 @@ __weak int arch_reserve_mmu(void)return 0 ; } -static int reserve_video (void ) + +static int reserve_video_from_videoblob (void ) {if (IS_ENABLED (CONFIG_SPL_VIDEO_HANDOFF ) &&spl_phase () >PHASE_SPL ) {struct video_handoff *ho;
@@ -412,8 +413,36 @@ static int reserve_video(void)if (!ho)return log_msg_ret ("blf" , -ENOENT );video_reserve_from_bloblist (ho); - gd->relocaddr = ho->fb; - }else if (CONFIG_IS_ENABLED (VIDEO )) { + +/* Sanity check fb from blob is before current relocaddr */ +if (likely (gd->relocaddr > (unsigned long ) ho->fb)) { + gd->relocaddr = ho->fb; + } + } + +return 0 ; +} + +/* +* Check if any bloblist received specifying reserved areas from previous stage and adjust +* gd->relocaddr accordingly, so that we start reserving after pre-reserved areas +* from previous stage. +* +* NOTE: +* IT is recommended that all bloblists from previous stage are reserved from ram_top +* as next stage will simply start reserving further regions after them. +*/ +static int setup_relocaddr_from_bloblist (void ) +{ +reserve_video_from_videoblob (); + +return 0 ; +} + + +static int reserve_video (void ) +{ +if (CONFIG_IS_ENABLED (VIDEO )) {ulong addr;int ret;
@@ -925,6 +954,7 @@ static const init_fnc_t init_sequence_f[] = { reserve_pram, #endif reserve_round_4k, + setup_relocaddr_from_bloblist, arch_reserve_mmu, reserve_video, reserve_trace,
Signature · 1 line
2.34.1
RFC PATCH 4/5 video: Skip framebuffer reservation if already reserved
In reply to Devarsh ThakkarSkip framebufer reservation if it was already reserved from previous stage and whose information was passed using a bloblist.
--- drivers/video/video-uclass.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/video/video-uclass.c +8 -0
@@ -123,6 +123,14 @@ int video_reserve(ulong *addrp)struct udevice *dev;ulong size; + +if (IS_ENABLED (CONFIG_SPL_VIDEO_HANDOFF ) &&spl_phase () >PHASE_SPL ) { +/* Skip allocation if already received a bloblist which +* filled below fields */ +if (gd->fb_base && gd->video_top && gd->video_bottom) +return 0 ; + } + gd->video_top = *addrp; for (uclass_find_first_device(UCLASS_VIDEO, &dev); dev;
Signature · 1 line
2.34.1
RFC PATCH 5/5 video: Fill video handoff in video post probe
In reply to Devarsh ThakkarFill video handoff fields in video_post_probe as at this point we have full framebuffer related information.
Also fill all the fields available in video hand-off struct as those were missing earlier and u-boot framework expects them to be filled for some of the functionalities.
--- drivers/video/video-uclass.c | 25 +++++++++++++++---------- 1 file changed, 15 insertions(+), 10 deletions(-)
drivers/video/video-uclass.c +15 -10
@@ -149,16 +149,6 @@ int video_reserve(ulong *addrp)debug ("Video frame buffers from %lx to %lx\n" , gd->video_bottom, gd->video_top); -if (spl_phase () ==PHASE_SPL &&CONFIG_IS_ENABLED (VIDEO_HANDOFF )) { -struct video_handoff *ho; - - ho =bloblist_add (BLOBLISTT_U_BOOT_VIDEO ,sizeof (*ho),0 ); -if (!ho) -return log_msg_ret ("blf" , -ENOENT ); - ho->fb = *addrp; - ho->size = size; - } -return 0 ; }
@@ -554,6 +544,21 @@ static int video_post_probe(struct udevice *dev) priv->fb_size = priv->line_length * priv->ysize; +/* Set up video handoff fields for passing video blob to next stage */ +if (spl_phase () ==PHASE_SPL &&CONFIG_IS_ENABLED (BLOBLIST )) { +struct video_handoff *ho; + + ho =bloblist_add (BLOBLISTT_U_BOOT_VIDEO ,sizeof (*ho),0 ); +if (!ho) +return log_msg_ret ("blf" , -ENOENT ); + ho->fb = gd->video_bottom; + ho->size = gd->video_top - gd->video_bottom; + ho->xsize = priv->xsize; + ho->ysize = priv->ysize; + ho->line_length = priv->line_length; + ho->bpix = priv->bpix; + } +if (IS_ENABLED (CONFIG_VIDEO_COPY ) && plat->copy_base) priv->copy_fb =map_sysmem (plat->copy_base, plat->size);
Signature · 1 line
2.34.1
Re: [RFC PATCH 1/5] arm: mach-k3: common: Reserve video memory from end of the RAM
In reply to Devarsh ThakkarHi Devarsh,
Quoted 35 lines · Devarsh Thakkar
Move the function to setup video memory before page table reservation so that framebuffer memory gets reserved from the end of RAM.
This is as per the new policy being discussed for passing blobs where each of the reserved areas for bloblists to be passed need to be reserved at the end of RAM.
This is to enable the next stage to directly skip the pre-reserved area from previous stage without having to making any gaps/holes to accomodate those regions which was the case if previous stage reserved region say somewhere in the middle and not at the end of RAM.
Suggested-by Simon Glass <[email protected]>Signed-off-by Devarsh Thakkar <[email protected]>--- arch/arm/mach-k3/common.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)arch/arm/mach-k3/common.c +1
-0@@ -27,6 +27,7 @@#include <env.h> #include <elf.h> #include <soc.h> +#include <video.h> #if IS_ENABLED (CONFIG_SYS_K3_SPL_ATF ) enum {
arch/arm/mach-k3/common.c void remove_fwl_configs(struct fwl_data *fwl_data, size_t fwl_data_size) · line 526
Quoted 4 lines
arch/arm/mach-k3/common.c +1
-0@@ -522,6 +523,24 @@ void remove_fwl_configs(struct fwl_data *fwl_data, size_t fwl_data_size) } } +static int video_setup (void )
Shouldn't this be in generic code?
Quoted 30 lines
arch/arm/mach-k3/common.c +19
-1+{ +if (CONFIG_IS_ENABLED (VIDEO )) { +ulong addr; +int ret; + + addr = gd->relocaddr; + ret =video_reserve (&addr); +if (ret) +return ret; +debug ("Reserving %luk for video at: %08lx\n" , + ((unsigned long )gd->relocaddr - addr) >>10 , addr); + gd->relocaddr = addr; + } + +return 0 ; +} +void spl_enable_dcache (void ) {#if !(defined(CONFIG_SYS_ICACHE_OFF ) && defined(CONFIG_SYS_DCACHE_OFF ))@@ -537,6 +556,8 @@ void spl_enable_dcache(void)if (ram_top >=0x100000000 ) ram_top = (phys_addr_t )0x100000000 ; + gd->relocaddr = ram_top; +video_setup (); gd->arch.tlb_addr = ram_top - gd->arch.tlb_size; gd->arch.tlb_addr &= ~(0x10000 -1 ); debug("TLB table from %08lx to %08lx\n", gd->arch.tlb_addr, --
Quoted 2 lines
2.34.1
Regards,
Simon
Re: [RFC PATCH 4/5] video: Skip framebuffer reservation if already reserved
In reply to Devarsh ThakkarHi Devarsh,
Quoted 9 lines · Devarsh Thakkar
Skip framebufer reservation if it was already reserved from previous stage and whose information was passed using a bloblist.
Signed-off-by Devarsh Thakkar <[email protected]>--- drivers/video/video-uclass.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/video/video-uclass.c int video_reserve(ulong *addrp) · line 129
Quoted 13 lines
drivers/video/video-uclass.c +4
-0@@ -123,6 +123,14 @@ int video_reserve(ulong *addrp)struct udevice *dev;ulong size; + +if (IS_ENABLED (CONFIG_SPL_VIDEO_HANDOFF ) &&spl_phase () >PHASE_SPL ) { +/* Skip allocation if already received a bloblist which +* filled below fields */
Comment style
/*
* Skip allocation ...
*/
Quoted 10 lines
drivers/video/video-uclass.c +4
-1+if (gd->fb_base && gd->video_top && gd->video_bottom) +return 0 ; + } + gd->video_top = *addrp; for (uclass_find_first_device(UCLASS_VIDEO, &dev); dev; --2.34.1
Re: [RFC PATCH 1/5] arm: mach-k3: common: Reserve video memory from end of the RAM
In reply to Simon GlassHi Simon,
Thanks for the review.
Quoted 41 lines · Simon Glass
Hi Devarsh,
Quoted 38 lines · Devarsh Thakkar
Move the function to setup video memory before page table reservation so that framebuffer memory gets reserved from the end of RAM.
This is as per the new policy being discussed for passing blobs where each of the reserved areas for bloblists to be passed need to be reserved at the end of RAM.
This is to enable the next stage to directly skip the pre-reserved area from previous stage without having to making any gaps/holes to accomodate those regions which was the case if previous stage reserved region say somewhere in the middle and not at the end of RAM.
Suggested-by Simon Glass <[email protected]>Signed-off-by Devarsh Thakkar <[email protected]>--- arch/arm/mach-k3/common.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)arch/arm/mach-k3/common.c +1
-0@@ -27,6 +27,7 @@#include <env.h> #include <elf.h> #include <soc.h> +#include <video.h> #if IS_ENABLED (CONFIG_SYS_K3_SPL_ATF ) enum {@@ -522,6 +523,24 @@ void remove_fwl_configs(struct fwl_data *fwl_data, size_t fwl_data_size) } }
Quoted 4 lines
arch/arm/mach-k3/common.c void remove_fwl_configs(struct fwl_data *fwl_data, size_t fwl_data_size) · line 526
Quoted 1 line
arch/arm/mach-k3/common.c +1
-0+static int video_setup (void )Shouldn't this be in generic code?
The reason I kept it here instead of video-uclass was since this function also uses and updates gd->relocaddr and not just reserves the memory region and I don't see any function in video-uclass playing with gd->relocaddr and this is inspired by and parallel to reserve_video from common/board_f.c which is also static function defined in board_f instead of video-uclass.
This basically is a wrapper function which calls video_reserve and also uses/updates gd->relocaddr, since I am calling this for SPL I could not find any common layer to define this since most vendors call board_init_f from platform specific file which in turn call this function.
Could you please share your opinion and suggestions for generic location if above still not look good?
Regards
Devarsh
Quoted 35 lines
Quoted 30 lines
arch/arm/mach-k3/common.c +19
-1+{ +if (CONFIG_IS_ENABLED (VIDEO )) { +ulong addr; +int ret; + + addr = gd->relocaddr; + ret =video_reserve (&addr); +if (ret) +return ret; +debug ("Reserving %luk for video at: %08lx\n" , + ((unsigned long )gd->relocaddr - addr) >>10 , addr); + gd->relocaddr = addr; + } + +return 0 ; +} +void spl_enable_dcache (void ) {#if !(defined(CONFIG_SYS_ICACHE_OFF ) && defined(CONFIG_SYS_DCACHE_OFF ))@@ -537,6 +556,8 @@ void spl_enable_dcache(void)if (ram_top >=0x100000000 ) ram_top = (phys_addr_t )0x100000000 ; + gd->relocaddr = ram_top; +video_setup (); gd->arch.tlb_addr = ram_top - gd->arch.tlb_size; gd->arch.tlb_addr &= ~(0x10000 -1 ); debug("TLB table from %08lx to %08lx\n", gd->arch.tlb_addr, --Quoted 2 lines
2.34.1
Regards,
Simon
Re: [RFC PATCH 1/5] arm: mach-k3: common: Reserve video memory from end of the RAM
Quoted 57 lines · Devarsh Thakkar
Hi Simon,
Thanks for the review.
Quoted 41 lines · Simon Glass
Hi Devarsh,
Quoted 38 lines · Devarsh Thakkar
Move the function to setup video memory before page table reservation so that framebuffer memory gets reserved from the end of RAM.
This is as per the new policy being discussed for passing blobs where each of the reserved areas for bloblists to be passed need to be reserved at the end of RAM.
This is to enable the next stage to directly skip the pre-reserved area from previous stage without having to making any gaps/holes to accomodate those regions which was the case if previous stage reserved region say somewhere in the middle and not at the end of RAM.
Suggested-by Simon Glass <[email protected]>Signed-off-by Devarsh Thakkar <[email protected]>--- arch/arm/mach-k3/common.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)arch/arm/mach-k3/common.c +1
-0@@ -27,6 +27,7 @@#include <env.h> #include <elf.h> #include <soc.h> +#include <video.h> #if IS_ENABLED (CONFIG_SYS_K3_SPL_ATF ) enum {@@ -522,6 +523,24 @@ void remove_fwl_configs(struct fwl_data *fwl_data, size_t fwl_data_size) } }Quoted 4 lines
arch/arm/mach-k3/common.c void remove_fwl_configs(struct fwl_data *fwl_data, size_t fwl_data_size) · line 526
Quoted 1 line
arch/arm/mach-k3/common.c +1
-0+static int video_setup (void )Shouldn't this be in generic code?
The reason I kept it here instead of video-uclass was since this function also uses and updates
gd->relocaddrand not just reserves the memory region and I don't see any function in video-uclass playing withgd->relocaddrand this is inspired by and parallel toreserve_videofromcommon/board_f.cwhich is also static function defined inboard_finstead of video-uclass.
Quoted 7 lines
This basically is a wrapper function which calls
video_reserveand also uses/updatesgd->relocaddr, since I am calling this for SPL I could not find any common layer to define this since most vendors callboard_init_ffrom platform specific file which in turn call this function.Could you please share your opinion and suggestions for generic location if above still not look good?
Unless Simon speaks up, this is probably fine enough and we can always do further cleanups afterwards. Please do a non-RFC where you address Simon's minor comments, thanks.
Signature · 1 line
Tom