Skip to contentSkip to conversation

generic/459: improve shutdown/read-only check to accommodate bcachefs

PATCH In review Brian Foster 2 participants 2 messages Nov 29, 2023

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 generic/459: improve shutdown/read-only check to accommodate bcachefs

generic/459 occasionally fails on bcachefs because the deliberately induced I/O errors caused by exhausting the overprovisioned thin pool can lead to filesystem shutdown. This test considers this expected behavior on certain fs', but only checks for the ext4 remount read-only behavior. bcachefs does a similar emergency read-only transition in response to certain I/O errors, but it behaves more similar to an XFS shutdown and doesn't necessarily reflect "ro" state in the mount table (unless induced by userspace).

Since the test already runs a touch command to help trigger the ext4 error handling sequence, this can be tweaked to serve double duty and also more accurately detect read-only status on bcachefs. Refactor into a small helper, check for touch command failure, and consider the fs read-only if either that or the mount entry check indicates it.

---

v2:
- Drop error filtering and just check touch failure.
- Comment tweaks.
v1: https://lore.kernel.org/fstests/[email protected]/

 tests/generic/459 | 28 +++++++++++++++++++++-------
 1 file changed, 21 insertions(+), 7 deletions(-)
tests/generic/459 +21 -7
index 4dd7a43b..c3f0b2b0 100755
@@ -57,6 +57,24 @@ origpsize=200
 virtsize=300
 newpsize=300
 
+# Check whether the filesystem has shutdown or remounted read-only. Shutdown
+# behavior can differ based on filesystem and configuration. Some fs' may not
+# have remounted without an additional write while others may have shutdown but
+# do not necessarily reflect read-only state in the mount options. Check both
+# here by first trying a simple write and following with an explicit ro check.
+is_shutdown_or_ro()
+{
+	ro=0
+
+	# if the fs has not shutdown, this may help trigger a remount-ro
+	touch $SCRATCH_MNT/newfile > /dev/null 2>&1 || ro=1
+
+	_fs_options /dev/mapper/$vgname-$snapname | grep -w "ro" > /dev/null
+	[ $? == 0 ] && ro=1
+
+	echo $ro
+}
+
 # Ensure we have enough disk space
 _scratch_mkfs_sized $((350 * 1024 * 1024)) >>$seqres.full 2>&1
 
@@ -113,13 +131,9 @@ ret=$?
 #	- The filesystem stays in Read-Write mode, but can be frozen/thawed
 #	  without getting stuck.
 if [ $ret -ne 0 ]; then
-	# freeze failed, filesystem should reject further writes and remount
-	# as readonly. Sometimes the previous write process won't trigger
-	# ro-remount, e.g. on ext3/4, do additional touch here to make sure
-	# filesystems see the metadata I/O error.
-	touch $SCRATCH_MNT/newfile >/dev/null 2>&1
-	ISRO=$(_fs_options /dev/mapper/$vgname-$snapname | grep -w "ro")
-	if [ -n "$ISRO" ]; then
+	# freeze failed, filesystem should reject further writes
+	ISRO=`is_shutdown_or_ro`
+	if [ $ISRO == 1 ]; then
 		echo "Test OK"
 	else
 		echo "Freeze failed and FS isn't Read-Only. Test Failed"
Signature · 1 line
2.41.0
Reviewed-by on v2 1/1
#1 lore raw
Quoted 9 lines · Brian Foster

generic/459 occasionally fails on bcachefs because the deliberately induced I/O errors caused by exhausting the overprovisioned thin pool can lead to filesystem shutdown. This test considers this expected behavior on certain fs', but only checks for the ext4 remount read-only behavior. bcachefs does a similar emergency read-only transition in response to certain I/O errors, but it behaves more similar to an XFS shutdown and doesn't necessarily reflect "ro" state in the mount table (unless induced by userspace).

Quoted 8 lines

Since the test already runs a touch command to help trigger the ext4 error handling sequence, this can be tweaked to serve double duty and also more accurately detect read-only status on bcachefs. Refactor into a small helper, check for touch command failure, and consider the fs read-only if either that or the mount entry check indicates it.

Looks fine.

Quoted 60 lines

---

v2:
- Drop error filtering and just check touch failure.
- Comment tweaks.
v1: https://lore.kernel.org/fstests/[email protected]/

 tests/generic/459 | 28 +++++++++++++++++++++-------
 1 file changed, 21 insertions(+), 7 deletions(-)
tests/generic/459 +21 -7
index 4dd7a43b..c3f0b2b0 100755
@@ -57,6 +57,24 @@ origpsize=200
 virtsize=300
 newpsize=300
 
+# Check whether the filesystem has shutdown or remounted read-only. Shutdown
+# behavior can differ based on filesystem and configuration. Some fs' may not
+# have remounted without an additional write while others may have shutdown but
+# do not necessarily reflect read-only state in the mount options. Check both
+# here by first trying a simple write and following with an explicit ro check.
+is_shutdown_or_ro()
+{
+	ro=0
+
+	# if the fs has not shutdown, this may help trigger a remount-ro
+	touch $SCRATCH_MNT/newfile > /dev/null 2>&1 || ro=1
+
+	_fs_options /dev/mapper/$vgname-$snapname | grep -w "ro" > /dev/null
+	[ $? == 0 ] && ro=1
+
+	echo $ro
+}
+
 # Ensure we have enough disk space
 _scratch_mkfs_sized $((350 * 1024 * 1024)) >>$seqres.full 2>&1
 
@@ -113,13 +131,9 @@ ret=$?
 #	- The filesystem stays in Read-Write mode, but can be frozen/thawed
 #	  without getting stuck.
 if [ $ret -ne 0 ]; then
-	# freeze failed, filesystem should reject further writes and remount
-	# as readonly. Sometimes the previous write process won't trigger
-	# ro-remount, e.g. on ext3/4, do additional touch here to make sure
-	# filesystems see the metadata I/O error.
-	touch $SCRATCH_MNT/newfile >/dev/null 2>&1
-	ISRO=$(_fs_options /dev/mapper/$vgname-$snapname | grep -w "ro")
-	if [ -n "$ISRO" ]; then
+	# freeze failed, filesystem should reject further writes
+	ISRO=`is_shutdown_or_ro`
+	if [ $ISRO == 1 ]; then
 		echo "Test OK"
 	else
 		echo "Freeze failed and FS isn't Read-Only. Test Failed"
Signature · 1 line
2.41.0