sync am65x device tree with Linux v6.7-rc1
PATCH 8/26 arm: dts: k3-am654: remove duplicate wkup_uart0
In reply to Bryan BrattlofWith the Linux and U-Boot board files unified, we now have a duplicate wkup_uart0 node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 12 ------------ 1 file changed, 12 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -12
@@ -18,7 +18,6 @@ ethernet0 = &cpsw_port1; remoteproc0 = &sysctrler; remoteproc1 = &a53_0; - serial0 = &wkup_uart0; serial1 = &mcu_uart0; serial2 = &main_uart0; spi0 = &ospi0;
@@ -117,8 +116,6 @@ }; &wkup_uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&wkup_uart0_pins_default>; status = "okay"; };
@@ -144,15 +141,6 @@ }; &wkup_pmx0 { - wkup_uart0_pins_default: wkup_uart0_pins_default { - pinctrl-single,pins = < - AM65X_WKUP_IOPAD(0x00a0, PIN_INPUT, 0) /* (AB1) WKUP_UART0_RXD */ - AM65X_WKUP_IOPAD(0x00a4, PIN_OUTPUT, 0) /* (AB5) WKUP_UART0_TXD */ - AM65X_WKUP_IOPAD(0x00c8, PIN_INPUT, 1) /* (AC2) WKUP_GPIO0_6.WKUP_UART0_CTSn */ - AM65X_WKUP_IOPAD(0x00cc, PIN_OUTPUT, 1) /* (AC1) WKUP_GPIO0_7.WKUP_UART0_RTSn */ - >; - }; - wkup_vtt_pins_default: wkup_vtt_pins_default { pinctrl-single,pins = < AM65X_WKUP_IOPAD(0x0040, PIN_OUTPUT_PULLUP, 7) /* WKUP_GPIO0_28 */
Signature · 1 line
2.43.0
PATCH 5/26 arm: dts: k3-am654: copy bootph properties to a53 dts
In reply to Bryan BrattlofIn order to unify the R5 board dtb file with the Linux board dtb file, we will need to copy all bootph-pre-ram properties to the *-u-boot.dtsi overlay.
--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 168 +++++++++++++++++++ arch/arm/dts/k3-am654-r5-base-board.dts | 83 --------- 2 files changed, 168 insertions(+), 83 deletions(-)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +168 -0
@@ -5,6 +5,174 @@ #include "k3-am65x-binman.dtsi" +&vtt_supply { + bootph-pre-ram; +}; + +&cbass_main { + bootph-pre-ram; +}; + +&main_navss { + bootph-pre-ram; +}; + +&cbass_mcu { + bootph-pre-ram; +}; + +&mcu_navss { + bootph-pre-ram; +}; + +&mcu_ringacc { + bootph-pre-ram; +}; + +&mcu_udmap { + bootph-pre-ram; +}; + +&wkup_gpio0 { + bootph-pre-ram; +}; + +&secure_proxy_main { + bootph-pre-ram; +}; + +&cbass_wakeup { + bootph-pre-ram; + + chipid@43000014 { + bootph-pre-ram; + }; +}; + +&dmsc { + bootph-pre-ram; +}; + +&k3_pds { + bootph-pre-ram; +}; + +&k3_clks { + bootph-pre-ram; +}; + +&k3_reset { + bootph-pre-ram; +}; + +&wkup_uart0 { + bootph-pre-ram; +}; + +&mcu_uart0 { + bootph-pre-ram; +}; + +&main_uart0 { + bootph-pre-ram; +}; + +&wkup_vtm0 { + bootph-pre-ram; +}; + +&wkup_pmx0 { + bootph-pre-ram; +}; + +&wkup_uart0_pins_default { + bootph-pre-ram; +}; + +&wkup_vtt_pins_default { + bootph-pre-ram; +}; + +&mcu_uart0_pins_default { + bootph-pre-ram; +}; + +&wkup_i2c_pins_default { + bootph-pre-ram; +}; + +&mcu_fss0_ospi0_pins_default { + bootph-pre-ram; +}; + +&main_pmx0 { + bootph-pre-ram; +}; + +&main_uart0_pins_default { + bootph-pre-ram; +}; + +&main_mmc0_pins_default { + bootph-pre-ram; +}; + +&main_mmc1_pins_default { + bootph-pre-ram; +}; + +&usb0_pins_default { + bootph-pre-ram; +}; + +&main_pmx1 { + bootph-pre-ram; +}; + +&sdhci0 { + bootph-pre-ram; +}; + +&sdhci1 { + bootph-pre-ram; +}; + +&wkup_i2c0 { + bootph-pre-ram; +}; + +&vdd_mpu { + bootph-pre-ram; +}; + +&ospi0 { + bootph-pre-ram; + + flash@0 { + bootph-pre-ram; + }; +}; + +&dwc3_0 { + bootph-pre-ram; +}; + +&usb0_phy { + bootph-pre-ram; +}; + +&usb0 { + bootph-pre-ram; +}; + +&scm_conf { + bootph-pre-ram; +}; + +&fss { + bootph-pre-ram; +}; + &pru0_0 { remoteproc-name = "pru0_0"; };
arch/arm/dts/k3-am654-r5-base-board.dts +0 -83
281 lines not on this page · raw message
Signature · 1 line
2.43.0
PATCH 11/26 arm: dts: k3-am654: remove duplicate mcu_udmap
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate mcu_udmap node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 13 ------------- 1 file changed, 13 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -13
@@ -52,19 +52,6 @@ #mbox-cells = <1>; bootph-pre-ram; }; - - mcu_navss: bus@28380000 { - dma-controller@285c0000 { - reg = <0x0 0x285c0000 0x0 0x100>, - <0x0 0x284c0000 0x0 0x4000>, - <0x0 0x2a800000 0x0 0x40000>, - <0x0 0x284a0000 0x0 0x4000>, - <0x0 0x2aa00000 0x0 0x40000>, - <0x0 0x28400000 0x0 0x2000>; - reg-names = "gcfg", "rchan", "rchanrt", "tchan", - "tchanrt", "rflow"; - }; - }; }; &cbass_wakeup {
Signature · 1 line
2.43.0
PATCH 18/26 arm: dts: k3-am654: remove duplicate ospi0 node
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate ospi0 node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 37 ------------------------- 1 file changed, 37 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -37
@@ -18,8 +18,6 @@ ethernet0 = &cpsw_port1; remoteproc0 = &sysctrler; remoteproc1 = &a53_0; - spi0 = &ospi0; - spi1 = &ospi1; usb0 = &usb0; usb1 = &usb1; };
@@ -111,22 +109,6 @@ AM65X_WKUP_IOPAD(0x0040, PIN_OUTPUT_PULLUP, 7) /* WKUP_GPIO0_28 */ >; }; - - mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins_default { - pinctrl-single,pins = < - AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* (V1) MCU_OSPI0_CLK */ - AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* (U2) MCU_OSPI0_DQS */ - AM65X_WKUP_IOPAD(0x000c, PIN_INPUT, 0) /* (U4) MCU_OSPI0_D0 */ - AM65X_WKUP_IOPAD(0x0010, PIN_INPUT, 0) /* (U5) MCU_OSPI0_D1 */ - AM65X_WKUP_IOPAD(0x0014, PIN_INPUT, 0) /* (T2) MCU_OSPI0_D2 */ - AM65X_WKUP_IOPAD(0x0018, PIN_INPUT, 0) /* (T3) MCU_OSPI0_D3 */ - AM65X_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* (T4) MCU_OSPI0_D4 */ - AM65X_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* (T5) MCU_OSPI0_D5 */ - AM65X_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* (R2) MCU_OSPI0_D6 */ - AM65X_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* (R3) MCU_OSPI0_D7 */ - AM65X_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* (R4) MCU_OSPI0_CSn0 */ - >; - }; }; &main_pmx0 {
@@ -170,27 +152,8 @@ }; &ospi0 { - pinctrl-names = "default"; - pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; - bootph-pre-ram; - reg = <0x0 0x47040000 0x0 0x100>, <0x0 0x50000000 0x0 0x8000000>; - - flash@0{ - compatible = "jedec,spi-nor"; - reg = <0x0>; - spi-tx-bus-width = <1>; - spi-rx-bus-width = <8>; - spi-max-frequency = <50000000>; - cdns,tshsl-ns = <60>; - cdns,tsd2d-ns = <60>; - cdns,tchsh-ns = <60>; - cdns,tslch-ns = <60>; - cdns,read-delay = <0>; - #address-cells = <1>; - #size-cells = <1>; - }; }; &main_pmx0 {
Signature · 1 line
2.43.0
cover sync am65x device tree with Linux v6.7-rc1
Hello Everyone!
This series gets the am65x booting again along with syncing the device tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64 files to make future syncs from Linux much easier. In the end the DTBs should look a lot like what the DTBs look like for the am64x which is fairly similar to the am65x.
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bc
Thanks for reviewing and happy holidays
~Bryan
Bryan Brattlof (26):
configs: am65x_evm_r5: enable driver for fixed regulators
configs: am65x_evm_a53: disable CONSOLE_MUX
arm: dts: k3-am654-r5: Merge board file and U-Boot overlay
arm: dts: k3-am654: pull in dtb update from Linux
arm: dts: k3-am654: copy bootph properties to a53 dts
arm: dts: k3-am654: include a53 board dtb for r5 build
arm: dts: k3-am654: remove duplicate vtt_supply
arm: dts: k3-am654: remove duplicate wkup_uart0
arm: dts: k3-am654: remove duplicate timer
arm: dts: k3-am654: remove duplicate mcu_ringacc
arm: dts: k3-am654: remove duplicate mcu_udmap
arm: dts: k3-am654: add needed regs to udmap nodes
arm: dts: k3-am654: remove duplicate mcu_uart0 node
arm: dts: k3-am654: remove duplicate main_uart0
arm: dts: k3-am654: remove duplicate sdhci0 pinmux node
arm: dts: k3-am654: remove duplicate sdhci1 pinmux node
arm: dts: k3-am654: remove duplicate wkup_i2c0
arm: dts: k3-am654: remove duplicate ospi0 node
arm: dts: k3-am654: remove usb0
arm: dts: k3-am654: remove duplicate mdio
arm: dts: k3-am654: remove duplicate vtt pinmux
arm: dts: k3-am654: remove duplicate root properties
arm: dts: k3-am654: remove un-needed aliases
arm: dts: k3-am654: move dummy_clock to root node
arm: dts: k3-am65: remove duplicate mcu secure proxy node
arm: dts: k3-am654: convert bootph-pre-ram to bootph-all
arch/arm/dts/k3-am65-main.dtsi | 342 +++++++++++++++--- arch/arm/dts/k3-am65-mcu.dtsi | 156 +++++++- arch/arm/dts/k3-am65-wakeup.dtsi | 10 +- arch/arm/dts/k3-am65.dtsi | 19 +- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 201 +++++++++- arch/arm/dts/k3-am654-base-board.dts | 301 +++++++++------ .../dts/k3-am654-r5-base-board-u-boot.dtsi | 208 ----------- arch/arm/dts/k3-am654-r5-base-board.dts | 298 +++------------ arch/arm/dts/k3-am654.dtsi | 7 + configs/am65x_evm_a53_defconfig | 1 - configs/am65x_evm_r5_defconfig | 2 + 11 files changed, 887 insertions(+), 658 deletions(-) delete mode 100644 arch/arm/dts/k3-am654-r5-base-board-u-boot.dtsi
base-commit: 2c9ee3f22603083ef0c4b808cf92645e5417156a
Signature · 1 line
2.43.0
PATCH 12/26 arm: dts: k3-am654: add needed regs to udmap nodes
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate. However there are a few missing registers ranges in the udmap nodes need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however they have not made it to a Linux tag. To keep DMA operational until the next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a note for our future selves.
[0] https://lore.kernel.org/r/[email protected]
--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 32 ++++++++++++++++++++ 1 file changed, 32 insertions(+)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +32 -0
@@ -260,3 +260,35 @@ &mcu_r5fss0 { ti,cluster-mode = <0>; }; + +/* The DMA driver requires a few extra register ranges + * which are missing for the am65x. A patch has been + * sent and will be synced after the v6.8-rc1 linux + * tag is published + */ +&main_udmap { + reg = <0x0 0x31150000 0x0 0x100>, + <0x0 0x34000000 0x0 0x100000>, + <0x0 0x35000000 0x0 0x100000>, + <0x0 0x30b00000 0x0 0x10000>, + <0x0 0x30c00000 0x0 0x10000>, + <0x0 0x30d00000 0x0 0x8000>; + reg-names = "gcfg", "rchanrt", "tchanrt", + "tchan", "rchan", "rflow"; +}; + +/* The DMA driver requires a few extra register ranges + * which are missing for the am65x. A patch has been + * sent and will be synced after the v6.8-rc1 linux + * tag is published + */ +&mcu_udmap { + reg = <0x0 0x285c0000 0x0 0x100>, + <0x0 0x2a800000 0x0 0x40000>, + <0x0 0x2aa00000 0x0 0x40000>, + <0x0 0x284a0000 0x0 0x4000>, + <0x0 0x284c0000 0x0 0x4000>, + <0x0 0x28400000 0x0 0x2000>; + reg-names = "gcfg", "rchanrt", "tchanrt", + "tchan", "rchan", "rflow"; +};
Signature · 1 line
2.43.0
PATCH 4/26 arm: dts: k3-am654: pull in dtb update from Linux
In reply to Bryan BrattlofPull in dtb updates for the am654 base board from v6.7-rc1 of Linux
--- arch/arm/dts/k3-am65-main.dtsi | 342 ++++++++++++++++++++++----- arch/arm/dts/k3-am65-mcu.dtsi | 156 ++++++++++-- arch/arm/dts/k3-am65-wakeup.dtsi | 10 +- arch/arm/dts/k3-am65.dtsi | 19 +- arch/arm/dts/k3-am654-base-board.dts | 301 ++++++++++++++--------- arch/arm/dts/k3-am654.dtsi | 7 + 6 files changed, 626 insertions(+), 209 deletions(-)
arch/arm/dts/k3-am65-main.dtsi +284 -58
@@ -35,7 +35,10 @@ #interrupt-cells = <3>; interrupt-controller; reg = <0x00 0x01800000 0x00 0x10000>, /* GICD */ - <0x00 0x01880000 0x00 0x90000>; /* GICR */ + <0x00 0x01880000 0x00 0x90000>, /* GICR */ + <0x00 0x6f000000 0x00 0x2000>, /* GICC */ + <0x00 0x6f010000 0x00 0x1000>, /* GICH */ + <0x00 0x6f020000 0x00 0x2000>; /* GICV */ /* * vcpumntirq: * virtual CPU interface maintenance interrupt
@@ -88,6 +91,7 @@ clock-frequency = <48000000>; current-speed = <115200>; power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; main_uart1: serial@2810000 {
@@ -96,6 +100,7 @@ interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; main_uart2: serial@2820000 {
@@ -104,29 +109,47 @@ interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; crypto: crypto@4e00000 { compatible = "ti,am654-sa2ul"; reg = <0x0 0x4e00000 0x0 0x1200>; - power-domains = <&k3_pds 136 TI_SCI_PD_EXCLUSIVE>; + power-domains = <&k3_pds 136 TI_SCI_PD_SHARED>; #address-cells = <2>; #size-cells = <2>; ranges = <0x0 0x04e00000 0x00 0x04e00000 0x0 0x30000>; - dmas = <&main_udmap 0xc000>, <&main_udmap 0x4000>, - <&main_udmap 0x4001>; + dmas = <&main_udmap 0xc001>, <&main_udmap 0x4002>, + <&main_udmap 0x4003>; dma-names = "tx", "rx1", "rx2"; - dma-coherent; rng: rng@4e10000 { compatible = "inside-secure,safexcel-eip76"; reg = <0x0 0x4e10000 0x0 0x7d>; interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&k3_clks 136 1>; + status = "disabled"; /* Used by OP-TEE */ }; }; + /* TIMERIO pad input CTRLMMR_TIMER*_CTRL registers */ + main_timerio_input: pinctrl@104200 { + compatible = "pinctrl-single"; + reg = <0x0 0x104200 0x0 0x30>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000001ff>; + }; + + /* TIMERIO pad output CTCTRLMMR_TIMERIO*_CTRL registers */ + main_timerio_output: pinctrl@104280 { + compatible = "pinctrl-single"; + reg = <0x0 0x104280 0x0 0x20>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000000f>; + }; + main_pmx0: pinctrl@11c000 { compatible = "pinctrl-single"; reg = <0x0 0x11c000 0x0 0x2e4>;
@@ -152,6 +175,7 @@ clock-names = "fck"; clocks = <&k3_clks 110 1>; power-domains = <&k3_pds 110 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; main_i2c1: i2c@2010000 {
@@ -163,6 +187,7 @@ clock-names = "fck"; clocks = <&k3_clks 111 1>; power-domains = <&k3_pds 111 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; main_i2c2: i2c@2020000 {
@@ -174,6 +199,7 @@ clock-names = "fck"; clocks = <&k3_clks 112 1>; power-domains = <&k3_pds 112 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; main_i2c3: i2c@2030000 {
@@ -185,6 +211,7 @@ clock-names = "fck"; clocks = <&k3_clks 113 1>; power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; ecap0: pwm@3100000 {
@@ -194,6 +221,7 @@ power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 39 0>; clock-names = "fck"; + status = "disabled"; }; main_spi0: spi@2100000 {
@@ -206,6 +234,7 @@ #size-cells = <0>; dmas = <&main_udmap 0xc500>, <&main_udmap 0x4500>; dma-names = "tx0", "rx0"; + status = "disabled"; }; main_spi1: spi@2110000 {
@@ -218,6 +247,7 @@ #size-cells = <0>; assigned-clocks = <&k3_clks 137 1>; assigned-clock-rates = <48000000>; + status = "disabled"; }; main_spi2: spi@2120000 {
@@ -228,6 +258,7 @@ power-domains = <&k3_pds 139 TI_SCI_PD_EXCLUSIVE>; #address-cells = <1>; #size-cells = <0>; + status = "disabled"; }; main_spi3: spi@2130000 {
@@ -238,6 +269,7 @@ power-domains = <&k3_pds 140 TI_SCI_PD_EXCLUSIVE>; #address-cells = <1>; #size-cells = <0>; + status = "disabled"; }; main_spi4: spi@2140000 {
@@ -248,6 +280,151 @@ power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>; #address-cells = <1>; #size-cells = <0>; + status = "disabled"; + }; + + main_timer0: timer@2400000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2400000 0x00 0x400>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 23 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 23 0>; + assigned-clock-parents = <&k3_clks 23 1>; + power-domains = <&k3_pds 23 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer1: timer@2410000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2410000 0x00 0x400>; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 24 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 24 0>; + assigned-clock-parents = <&k3_clks 24 1>; + power-domains = <&k3_pds 24 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer2: timer@2420000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2420000 0x00 0x400>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 27 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 27 0>; + assigned-clock-parents = <&k3_clks 27 1>; + power-domains = <&k3_pds 27 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer3: timer@2430000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2430000 0x00 0x400>; + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 28 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 28 0>; + assigned-clock-parents = <&k3_clks 28 1>; + power-domains = <&k3_pds 28 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer4: timer@2440000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2440000 0x00 0x400>; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 29 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 29 0>; + assigned-clock-parents = <&k3_clks 29 1>; + power-domains = <&k3_pds 29 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer5: timer@2450000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2450000 0x00 0x400>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 30 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 30 0>; + assigned-clock-parents = <&k3_clks 30 1>; + power-domains = <&k3_pds 30 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer6: timer@2460000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2460000 0x00 0x400>; + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 31 0>; + assigned-clocks = <&k3_clks 31 0>; + assigned-clock-parents = <&k3_clks 31 1>; + clock-names = "fck"; + power-domains = <&k3_pds 31 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>; + interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 32 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 32 0>; + assigned-clock-parents = <&k3_clks 32 1>; + power-domains = <&k3_pds 32 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer8: timer@2480000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2480000 0x00 0x400>; + interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 33 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 33 0>; + assigned-clock-parents = <&k3_clks 33 1>; + power-domains = <&k3_pds 33 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer9: timer@2490000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2490000 0x00 0x400>; + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 34 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 34 0>; + assigned-clock-parents = <&k3_clks 34 1>; + power-domains = <&k3_pds 34 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer10: timer@24a0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24a0000 0x00 0x400>; + interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 25 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 25 0>; + assigned-clock-parents = <&k3_clks 25 1>; + power-domains = <&k3_pds 25 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer11: timer@24b0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24b0000 0x00 0x400>; + interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 26 0>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 26 0>; + assigned-clock-parents = <&k3_clks 26 1>; + power-domains = <&k3_pds 26 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; }; sdhci0: mmc@4f80000 {
@@ -292,7 +469,6 @@ ti,otap-del-sel-ddr52 = <0x4>; ti,otap-del-sel-hs200 = <0x7>; ti,clkbuf-sel = <0x7>; - ti,otap-del-sel = <0x2>; ti,trm-icp = <0x8>; dma-coherent; };
@@ -304,21 +480,6 @@ #size-cells = <1>; ranges = <0x0 0x0 0x00100000 0x1c000>; - pcie0_mode: pcie-mode@4060 { - compatible = "syscon"; - reg = <0x00004060 0x4>; - }; - - pcie1_mode: pcie-mode@4070 { - compatible = "syscon"; - reg = <0x00004070 0x4>; - }; - - pcie_devid: pcie-devid@210 { - compatible = "syscon"; - reg = <0x00000210 0x4>; - }; - serdes0_clk: clock@4080 { compatible = "syscon"; reg = <0x00004080 0x4>;
@@ -338,11 +499,11 @@ dss_oldi_io_ctrl: dss-oldi-io-ctrl@41e0 { compatible = "syscon"; - reg = <0x0000041e0 0x14>; + reg = <0x000041e0 0x14>; }; - ehrpwm_tbclk: clock@4140 { - compatible = "ti,am654-ehrpwm-tbclk", "syscon"; + ehrpwm_tbclk: clock-controller@4140 { + compatible = "ti,am654-ehrpwm-tbclk"; reg = <0x4140 0x18>; #clock-cells = <1>; };
@@ -439,7 +600,7 @@ }; main_navss: bus@30800000 { - compatible = "simple-mfd"; + compatible = "simple-bus"; #address-cells = <2>; #size-cells = <2>; ranges = <0x0 0x30800000 0x0 0x30800000 0x0 0xbc00000>;
@@ -497,6 +658,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster1: mailbox@31f81000 {
@@ -506,6 +668,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster2: mailbox@31f82000 {
@@ -515,6 +678,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster3: mailbox@31f83000 {
@@ -524,6 +688,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster4: mailbox@31f84000 {
@@ -533,6 +698,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster5: mailbox@31f85000 {
@@ -542,6 +708,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster6: mailbox@31f86000 {
@@ -551,6 +718,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster7: mailbox@31f87000 {
@@ -560,6 +728,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster8: mailbox@31f88000 {
@@ -569,6 +738,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster9: mailbox@31f89000 {
@@ -578,6 +748,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster10: mailbox@31f8a000 {
@@ -587,6 +758,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; mailbox0_cluster11: mailbox@31f8b000 {
@@ -596,15 +768,17 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; interrupt-parent = <&intr_main_navss>; + status = "disabled"; }; ringacc: ringacc@3c000000 { compatible = "ti,am654-navss-ringacc"; - reg = <0x0 0x3c000000 0x0 0x400000>, - <0x0 0x38000000 0x0 0x400000>, - <0x0 0x31120000 0x0 0x100>, - <0x0 0x33000000 0x0 0x40000>; - reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target"; + reg = <0x0 0x3c000000 0x0 0x400000>, + <0x0 0x38000000 0x0 0x400000>, + <0x0 0x31120000 0x0 0x100>, + <0x0 0x33000000 0x0 0x40000>, + <0x0 0x31080000 0x0 0x40000>; + reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target", "cfg"; ti,num-rings = <818>; ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */ ti,sci = <&dmsc>;
@@ -614,9 +788,9 @@ main_udmap: dma-controller@31150000 { compatible = "ti,am654-navss-main-udmap"; - reg = <0x0 0x31150000 0x0 0x100>, - <0x0 0x34000000 0x0 0x100000>, - <0x0 0x35000000 0x0 0x100000>; + reg = <0x0 0x31150000 0x0 0x100>, + <0x0 0x34000000 0x0 0x100000>, + <0x0 0x35000000 0x0 0x100000>; reg-names = "gcfg", "rchanrt", "tchanrt"; msi-parent = <&inta_main_udmass>; #dma-cells = <1>;
@@ -687,15 +861,15 @@ pcie0_rc: pcie@5500000 { compatible = "ti,am654-pcie-rc"; - reg = <0x0 0x5500000 0x0 0x1000>, <0x0 0x5501000 0x0 0x1000>, <0x0 0x10000000 0x0 0x2000>, <0x0 0x5506000 0x0 0x1000>; + reg = <0x0 0x5500000 0x0 0x1000>, <0x0 0x5501000 0x0 0x1000>, <0x0 0x10000000 0x0 0x2000>, <0x0 0x5506000 0x0 0x1000>; reg-names = "app", "dbics", "config", "atu"; power-domains = <&k3_pds 120 TI_SCI_PD_EXCLUSIVE>; #address-cells = <3>; #size-cells = <2>; - ranges = <0x81000000 0 0 0x0 0x10020000 0 0x00010000 - 0x82000000 0 0x10030000 0x0 0x10030000 0 0x07FD0000>; - ti,syscon-pcie-id = <&pcie_devid>; - ti,syscon-pcie-mode = <&pcie0_mode>; + ranges = <0x81000000 0 0 0x0 0x10020000 0 0x00010000>, + <0x82000000 0 0x10030000 0x0 0x10030000 0 0x07FD0000>; + ti,syscon-pcie-id = <&scm_conf 0x210>; + ti,syscon-pcie-mode = <&scm_conf 0x4060>; bus-range = <0x0 0xff>; num-viewport = <16>; max-link-speed = <2>;
@@ -703,32 +877,34 @@ interrupts = <GIC_SPI 340 IRQ_TYPE_EDGE_RISING>; msi-map = <0x0 &gic_its 0x0 0x10000>; device_type = "pci"; + status = "disabled"; }; pcie0_ep: pcie-ep@5500000 { compatible = "ti,am654-pcie-ep"; - reg = <0x0 0x5500000 0x0 0x1000>, <0x0 0x5501000 0x0 0x1000>, <0x0 0x10000000 0x0 0x8000000>, <0x0 0x5506000 0x0 0x1000>; + reg = <0x0 0x5500000 0x0 0x1000>, <0x0 0x5501000 0x0 0x1000>, <0x0 0x10000000 0x0 0x8000000>, <0x0 0x5506000 0x0 0x1000>; reg-names = "app", "dbics", "addr_space", "atu"; power-domains = <&k3_pds 120 TI_SCI_PD_EXCLUSIVE>; - ti,syscon-pcie-mode = <&pcie0_mode>; + ti,syscon-pcie-mode = <&scm_conf 0x4060>; num-ib-windows = <16>; num-ob-windows = <16>; max-link-speed = <2>; dma-coherent; interrupts = <GIC_SPI 340 IRQ_TYPE_EDGE_RISING>; + status = "disabled"; }; pcie1_rc: pcie@5600000 { compatible = "ti,am654-pcie-rc"; - reg = <0x0 0x5600000 0x0 0x1000>, <0x0 0x5601000 0x0 0x1000>, <0x0 0x18000000 0x0 0x2000>, <0x0 0x5606000 0x0 0x1000>; + reg = <0x0 0x5600000 0x0 0x1000>, <0x0 0x5601000 0x0 0x1000>, <0x0 0x18000000 0x0 0x2000>, <0x0 0x5606000 0x0 0x1000>; reg-names = "app", "dbics", "config", "atu"; power-domains = <&k3_pds 121 TI_SCI_PD_EXCLUSIVE>; #address-cells = <3>; #size-cells = <2>; - ranges = <0x81000000 0 0 0x0 0x18020000 0 0x00010000 - 0x82000000 0 0x18030000 0x0 0x18030000 0 0x07FD0000>; - ti,syscon-pcie-id = <&pcie_devid>; - ti,syscon-pcie-mode = <&pcie1_mode>; + ranges = <0x81000000 0 0 0x0 0x18020000 0 0x00010000>, + <0x82000000 0 0x18030000 0x0 0x18030000 0 0x07FD0000>; + ti,syscon-pcie-id = <&scm_conf 0x210>; + ti,syscon-pcie-mode = <&scm_conf 0x4070>; bus-range = <0x0 0xff>; num-viewport = <16>; max-link-speed = <2>;
@@ -736,19 +912,21 @@ interrupts = <GIC_SPI 355 IRQ_TYPE_EDGE_RISING>; msi-map = <0x0 &gic_its 0x10000 0x10000>; device_type = "pci"; + status = "disabled"; }; pcie1_ep: pcie-ep@5600000 { compatible = "ti,am654-pcie-ep"; - reg = <0x0 0x5600000 0x0 0x1000>, <0x0 0x5601000 0x0 0x1000>, <0x0 0x18000000 0x0 0x4000000>, <0x0 0x5606000 0x0 0x1000>; + reg = <0x0 0x5600000 0x0 0x1000>, <0x0 0x5601000 0x0 0x1000>, <0x0 0x18000000 0x0 0x4000000>, <0x0 0x5606000 0x0 0x1000>; reg-names = "app", "dbics", "addr_space", "atu"; power-domains = <&k3_pds 121 TI_SCI_PD_EXCLUSIVE>; - ti,syscon-pcie-mode = <&pcie1_mode>; + ti,syscon-pcie-mode = <&scm_conf 0x4070>; num-ib-windows = <16>; num-ob-windows = <16>; max-link-speed = <2>; dma-coherent; interrupts = <GIC_SPI 355 IRQ_TYPE_EDGE_RISING>; + status = "disabled"; }; mcasp0: mcasp@2b00000 {
@@ -766,6 +944,7 @@ clocks = <&k3_clks 104 0>; clock-names = "fck"; power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; mcasp1: mcasp@2b10000 {
@@ -783,6 +962,7 @@ clocks = <&k3_clks 105 0>; clock-names = "fck"; power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; mcasp2: mcasp@2b20000 {
@@ -800,6 +980,7 @@ clocks = <&k3_clks 106 0>; clock-names = "fck"; power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; cal: cal@6f03000 {
@@ -826,13 +1007,13 @@ dss: dss@4a00000 { compatible = "ti,am65x-dss"; - reg = <0x0 0x04a00000 0x0 0x1000>, /* common */ - <0x0 0x04a02000 0x0 0x1000>, /* vidl1 */ - <0x0 0x04a06000 0x0 0x1000>, /* vid */ - <0x0 0x04a07000 0x0 0x1000>, /* ovr1 */ - <0x0 0x04a08000 0x0 0x1000>, /* ovr2 */ - <0x0 0x04a0a000 0x0 0x1000>, /* vp1 */ - <0x0 0x04a0b000 0x0 0x1000>; /* vp2 */ + reg = <0x0 0x04a00000 0x0 0x1000>, /* common */ + <0x0 0x04a02000 0x0 0x1000>, /* vidl1 */ + <0x0 0x04a06000 0x0 0x1000>, /* vid */ + <0x0 0x04a07000 0x0 0x1000>, /* ovr1 */ + <0x0 0x04a08000 0x0 0x1000>, /* ovr2 */ + <0x0 0x04a0a000 0x0 0x1000>, /* vp1 */ + <0x0 0x04a0b000 0x0 0x1000>; /* vp2 */ reg-names = "common", "vidl1", "vid", "ovr1", "ovr2", "vp1", "vp2";
@@ -840,9 +1021,9 @@ power-domains = <&k3_pds 67 TI_SCI_PD_EXCLUSIVE>; - clocks = <&k3_clks 67 1>, - <&k3_clks 216 1>, - <&k3_clks 67 2>; + clocks = <&k3_clks 67 1>, + <&k3_clks 216 1>, + <&k3_clks 67 2>; clock-names = "fck", "vp1", "vp2"; /*
@@ -870,6 +1051,7 @@ power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>; clocks = <&ehrpwm_tbclk 0>, <&k3_clks 40 0>; clock-names = "tbclk", "fck"; + status = "disabled"; }; ehrpwm1: pwm@3010000 {
@@ -879,6 +1061,7 @@ power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>; clocks = <&ehrpwm_tbclk 1>, <&k3_clks 41 0>; clock-names = "tbclk", "fck"; + status = "disabled"; }; ehrpwm2: pwm@3020000 {
@@ -888,6 +1071,7 @@ power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>; clocks = <&ehrpwm_tbclk 2>, <&k3_clks 42 0>; clock-names = "tbclk", "fck"; + status = "disabled"; }; ehrpwm3: pwm@3030000 {
@@ -897,6 +1081,7 @@ power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>; clocks = <&ehrpwm_tbclk 3>, <&k3_clks 43 0>; clock-names = "tbclk", "fck"; + status = "disabled"; }; ehrpwm4: pwm@3040000 {
@@ -906,6 +1091,7 @@ power-domains = <&k3_pds 44 TI_SCI_PD_EXCLUSIVE>; clocks = <&ehrpwm_tbclk 4>, <&k3_clks 44 0>; clock-names = "tbclk", "fck"; + status = "disabled"; }; ehrpwm5: pwm@3050000 {
@@ -915,6 +1101,7 @@ power-domains = <&k3_pds 45 TI_SCI_PD_EXCLUSIVE>; clocks = <&ehrpwm_tbclk 5>, <&k3_clks 45 0>; clock-names = "tbclk", "fck"; + status = "disabled"; }; icssg0: icssg@b000000 {
@@ -964,6 +1151,18 @@ }; }; + icssg0_iep0: iep@2e000 { + compatible = "ti,am654-icss-iep"; + reg = <0x2e000 0x1000>; + clocks = <&icssg0_iepclk_mux>; + }; + + icssg0_iep1: iep@2f000 { + compatible = "ti,am654-icss-iep"; + reg = <0x2f000 0x1000>; + clocks = <&icssg0_iepclk_mux>; + }; + icssg0_mii_rt: mii-rt@32000 { compatible = "ti,pruss-mii", "syscon"; reg = <0x32000 0x100>;
@@ -1055,6 +1254,7 @@ #address-cells = <1>; #size-cells = <0>; bus_freq = <1000000>; + status = "disabled"; }; };
@@ -1105,6 +1305,18 @@ }; }; + icssg1_iep0: iep@2e000 { + compatible = "ti,am654-icss-iep"; + reg = <0x2e000 0x1000>; + clocks = <&icssg1_iepclk_mux>; + }; + + icssg1_iep1: iep@2f000 { + compatible = "ti,am654-icss-iep"; + reg = <0x2f000 0x1000>; + clocks = <&icssg1_iepclk_mux>; + }; + icssg1_mii_rt: mii-rt@32000 { compatible = "ti,pruss-mii", "syscon"; reg = <0x32000 0x100>;
@@ -1196,6 +1408,7 @@ #address-cells = <1>; #size-cells = <0>; bus_freq = <1000000>; + status = "disabled"; }; };
@@ -1246,6 +1459,18 @@ }; }; + icssg2_iep0: iep@2e000 { + compatible = "ti,am654-icss-iep"; + reg = <0x2e000 0x1000>; + clocks = <&icssg2_iepclk_mux>; + }; + + icssg2_iep1: iep@2f000 { + compatible = "ti,am654-icss-iep"; + reg = <0x2f000 0x1000>; + clocks = <&icssg2_iepclk_mux>; + }; + icssg2_mii_rt: mii-rt@32000 { compatible = "ti,pruss-mii", "syscon"; reg = <0x32000 0x100>;
@@ -1337,6 +1562,7 @@ #address-cells = <1>; #size-cells = <0>; bus_freq = <1000000>; + status = "disabled"; }; }; };
arch/arm/dts/k3-am65-mcu.dtsi +139 -17
249 lines not on this page · raw message
arch/arm/dts/k3-am65-wakeup.dtsi +4 -6
@@ -12,8 +12,8 @@ mbox-names = "rx", "tx"; - mboxes= <&secure_proxy_main 11>, - <&secure_proxy_main 13>; + mboxes = <&secure_proxy_main 11>, + <&secure_proxy_main 13>; reg-names = "debug_messages"; reg = <0x44083000 0x1000>;
@@ -54,6 +54,7 @@ clock-frequency = <48000000>; current-speed = <115200>; power-domains = <&k3_pds 150 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; wkup_i2c0: i2c@42120000 {
@@ -65,6 +66,7 @@ clock-names = "fck"; clocks = <&k3_clks 115 1>; power-domains = <&k3_pds 115 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; }; intr_wkup_gpio: interrupt-controller@42200000 {
@@ -100,8 +102,4 @@ power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>; #thermal-sensor-cells = <1>; }; - - thermal_zones: thermal-zones { - #include "k3-am654-industrial-thermal.dtsi" - }; };
arch/arm/dts/k3-am65.dtsi +3 -16
@@ -8,9 +8,10 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/pinctrl/k3.h> #include <dt-bindings/soc/ti,sci_pm_domain.h> +#include "k3-pinctrl.h" + / { model = "Texas Instruments K3 AM654 SoC"; compatible = "ti,am654";
@@ -18,21 +19,6 @@ #address-cells = <2>; #size-cells = <2>; - aliases { - serial0 = &wkup_uart0; - serial1 = &mcu_uart0; - serial2 = &main_uart0; - serial3 = &main_uart1; - serial4 = &main_uart2; - i2c0 = &wkup_i2c0; - i2c1 = &mcu_i2c0; - i2c2 = &main_i2c0; - i2c3 = &main_i2c1; - i2c4 = &main_i2c2; - i2c5 = &main_i2c3; - ethernet0 = &cpsw_port1; - }; - chosen { }; firmware {
@@ -84,6 +70,7 @@ <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>, <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>, <0x00 0x50000000 0x00 0x50000000 0x00 0x8000000>, + <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A53 PERIPHBASE */ <0x00 0x70000000 0x00 0x70000000 0x00 0x200000>, <0x05 0x00000000 0x05 0x00000000 0x01 0x0000000>, <0x07 0x00000000 0x07 0x00000000 0x01 0x0000000>;
arch/arm/dts/k3-am654-base-board.dts +189 -112
558 lines not on this page · raw message
arch/arm/dts/k3-am654.dtsi +7 -0
@@ -93,6 +93,7 @@ L2_0: l2-cache0 { compatible = "cache"; cache-level = <2>; + cache-unified; cache-size = <0x80000>; cache-line-size = <64>; cache-sets = <512>;
@@ -102,6 +103,7 @@ L2_1: l2-cache1 { compatible = "cache"; cache-level = <2>; + cache-unified; cache-size = <0x80000>; cache-line-size = <64>; cache-sets = <512>;
@@ -111,5 +113,10 @@ msmc_l3: l3-cache0 { compatible = "cache"; cache-level = <3>; + cache-unified; + }; + + thermal_zones: thermal-zones { + #include "k3-am654-industrial-thermal.dtsi" }; };
Signature · 1 line
2.43.0
PATCH 23/26 arm: dts: k3-am654: remove un-needed aliases
In reply to Bryan BrattlofThese aliases are not needed in U-Boot. Remove them
--- arch/arm/dts/k3-am654-r5-base-board.dts | 1 - 1 file changed, 1 deletion(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -1
@@ -12,7 +12,6 @@ / { aliases { - ethernet0 = &cpsw_port1; remoteproc0 = &sysctrler; remoteproc1 = &a53_0; };
Signature · 1 line
2.43.0
PATCH 19/26 arm: dts: k3-am654: remove usb0
In reply to Bryan BrattlofThe pinmux for usb0 is missing from the Linux board dtb file. Remove it until we can introduce it in Linux
--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 12 -------- arch/arm/dts/k3-am654-r5-base-board.dts | 29 -------------------- 2 files changed, 41 deletions(-)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +0 -12
@@ -133,10 +133,6 @@ bootph-pre-ram; }; -&usb0_pins_default { - bootph-pre-ram; -}; - &main_pmx1 { bootph-pre-ram; };
@@ -169,14 +165,6 @@ bootph-pre-ram; }; -&usb0_phy { - bootph-pre-ram; -}; - -&usb0 { - bootph-pre-ram; -}; - &scm_conf { bootph-pre-ram; };
arch/arm/dts/k3-am654-r5-base-board.dts +0 -29
@@ -18,8 +18,6 @@ ethernet0 = &cpsw_port1; remoteproc0 = &sysctrler; remoteproc1 = &a53_0; - usb0 = &usb0; - usb1 = &usb1; }; a53_0: a53@0 {
@@ -111,14 +109,6 @@ }; }; -&main_pmx0 { - usb0_pins_default: usb0_pins_default { - pinctrl-single,pins = < - AM65X_IOPAD(0x02bc, PIN_OUTPUT, 0) /* (AD9) USB0_DRVVBUS */ - >; - }; -}; - &memorycontroller { vtt-supply = <&vtt_supply>; pinctrl-names = "default";
@@ -156,14 +146,6 @@ <0x0 0x50000000 0x0 0x8000000>; }; -&main_pmx0 { - usb0_pins_default: usb0_pins_default { - pinctrl-single,pins = < - AM65X_IOPAD(0x02bc, PIN_OUTPUT, 0) /* (AD9) USB0_DRVVBUS */ - >; - }; -}; - &dwc3_0 { status = "okay"; /delete-property/ clocks;
@@ -172,17 +154,6 @@ /delete-property/ assigned-clock-parents; }; -&usb0_phy { - status = "okay"; - /delete-property/ clocks; -}; - -&usb0 { - pinctrl-names = "default"; - pinctrl-0 = <&usb0_pins_default>; - dr_mode = "peripheral"; -}; - &davinci_mdio { phy0: ethernet-phy@0 { reg = <0>;
Signature · 1 line
2.43.0
PATCH 22/26 arm: dts: k3-am654: remove duplicate root properties
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we have duplicate properties in the root node. Remove them
--- arch/arm/dts/k3-am654-r5-base-board.dts | 3 --- 1 file changed, 3 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -3
@@ -11,9 +11,6 @@ #include "k3-am654-ddr.dtsi" / { - compatible = "ti,am654-evm", "ti,am654"; - model = "Texas Instruments AM654 R5 Base Board"; - aliases { ethernet0 = &cpsw_port1; remoteproc0 = &sysctrler;
Signature · 1 line
2.43.0
PATCH 10/26 arm: dts: k3-am654: remove duplicate mcu_ringacc
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate mcu_ringacc node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 10 ---------- 1 file changed, 10 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -10
@@ -54,16 +54,6 @@ }; mcu_navss: bus@28380000 { - ringacc@2b800000 { - reg = <0x0 0x2b800000 0x0 0x400000>, - <0x0 0x2b000000 0x0 0x400000>, - <0x0 0x28590000 0x0 0x100>, - <0x0 0x2a500000 0x0 0x40000>, - <0x0 0x28440000 0x0 0x40000>; - reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target", "cfg"; - ti,dma-ring-reset-quirk; - }; - dma-controller@285c0000 { reg = <0x0 0x285c0000 0x0 0x100>, <0x0 0x284c0000 0x0 0x4000>,
Signature · 1 line
2.43.0
PATCH 24/26 arm: dts: k3-am654: move dummy_clock to root node
In reply to Bryan BrattlofThe dummy_clock node is used to help the drivers probe the IO needed to setup consoles and boot media to load firmware into the SoC.
This dummy_clock isn't a device that exists nor does it exist in the mcu domain. So move it from cbass_mcu to the root node to avoid any confusion.
--- arch/arm/dts/k3-am654-r5-base-board.dts | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +7 -7
@@ -30,6 +30,13 @@ ti,sci-host-id = <10>; bootph-pre-ram; }; + + clk_200mhz: dummy_clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <200000000>; + bootph-pre-ram; + }; }; &cbass_mcu {
@@ -51,13 +58,6 @@ mbox-names = "tx", "rx"; bootph-pre-ram; }; - - clk_200mhz: dummy_clock { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <200000000>; - bootph-pre-ram; - }; }; /* timer init is called as part of rproc_start() while
Signature · 1 line
2.43.0
PATCH 6/26 arm: dts: k3-am654: include a53 board dtb for r5 build
In reply to Bryan BrattlofTo make things as organized as possible, start from the Libux board dtbs and apply all properties needed for U-Boot in our *-u-boot.dtsi file for the MAIN SPL and U-Boot builds.
We can then include these files for the WKUP SPL build making further edits to the needed properties and nodes for the WKUP SPL bootloader's view of the am65x.
--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 2 +- arch/arm/dts/k3-am654-r5-base-board.dts | 3 ++- 2 files changed, 3 insertions(+), 2 deletions(-)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +1 -1
@@ -97,7 +97,7 @@ bootph-pre-ram; }; -&wkup_i2c_pins_default { +&wkup_i2c0_pins_default { bootph-pre-ram; };
arch/arm/dts/k3-am654-r5-base-board.dts +2 -1
@@ -5,7 +5,8 @@ /dts-v1/; -#include "k3-am654.dtsi" +#include "k3-am654-base-board.dts" +#include "k3-am654-base-board-u-boot.dtsi" #include "k3-am654-base-board-ddr4-1600MTs.dtsi" #include "k3-am654-ddr.dtsi"
Signature · 1 line
2.43.0
PATCH 7/26 arm: dts: k3-am654: remove duplicate vtt_supply
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified we now have a duplicate vtt_supply node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 9 --------- 1 file changed, 9 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -9
@@ -46,15 +46,6 @@ ti,sci-host-id = <10>; bootph-pre-ram; }; - - vtt_supply: vtt_supply { - compatible = "regulator-gpio"; - regulator-name = "vtt"; - regulator-min-microvolt = <0>; - regulator-max-microvolt = <3300000>; - gpios = <&wkup_gpio0 28 GPIO_ACTIVE_HIGH>; - states = <0 0x0 3300000 0x1>; - }; }; &cbass_main {
Signature · 1 line
2.43.0
PATCH 14/26 arm: dts: k3-am654: remove duplicate main_uart0
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate main_uart0 node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 17 ----------------- 1 file changed, 17 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -17
@@ -18,7 +18,6 @@ ethernet0 = &cpsw_port1; remoteproc0 = &sysctrler; remoteproc1 = &a53_0; - serial2 = &main_uart0; spi0 = &ospi0; spi1 = &ospi1; usb0 = &usb0;
@@ -100,13 +99,6 @@ status = "okay"; }; -&main_uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&main_uart0_pins_default>; - power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>; - status = "okay"; -}; - &wkup_vtm0 { compatible = "ti,am654-vtm", "ti,am654-avs"; vdd-supply-3 = <&vdd_mpu>;
@@ -145,15 +137,6 @@ }; &main_pmx0 { - main_uart0_pins_default: main-uart0-pins-default { - pinctrl-single,pins = < - AM65X_IOPAD(0x01e4, PIN_INPUT, 0) /* (AF11) UART0_RXD */ - AM65X_IOPAD(0x01e8, PIN_OUTPUT, 0) /* (AE11) UART0_TXD */ - AM65X_IOPAD(0x01ec, PIN_INPUT, 0) /* (AG11) UART0_CTSn */ - AM65X_IOPAD(0x01f0, PIN_OUTPUT, 0) /* (AD11) UART0_RTSn */ - >; - }; - main_mmc0_pins_default: main_mmc0_pins_default { pinctrl-single,pins = < AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */
Signature · 1 line
2.43.0
PATCH 25/26 arm: dts: k3-am65: remove duplicate mcu secure proxy node
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate mcu secure proxy node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 19 +++++++------------ 1 file changed, 7 insertions(+), 12 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +7 -12
@@ -39,22 +39,15 @@ }; }; -&cbass_mcu { - mcu_secproxy: secproxy@28380000 { - compatible = "ti,am654-secure-proxy"; - reg = <0x0 0x2a380000 0x0 0x80000>, - <0x0 0x2a400000 0x0 0x80000>, - <0x0 0x2a480000 0x0 0x80000>; - reg-names = "rt", "scfg", "target_data"; - #mbox-cells = <1>; - bootph-pre-ram; - }; +&secure_proxy_mcu { + status = "okay"; + bootph-pre-ram; }; &cbass_wakeup { sysctrler: sysctrler { compatible = "ti,am654-system-controller"; - mboxes= <&mcu_secproxy 4>, <&mcu_secproxy 5>; + mboxes= <&secure_proxy_mcu 4>, <&secure_proxy_mcu 5>; mbox-names = "tx", "rx"; bootph-pre-ram; };
@@ -75,7 +68,9 @@ }; &dmsc { - mboxes= <&mcu_secproxy 8>, <&mcu_secproxy 6>, <&mcu_secproxy 5>; + mboxes = <&secure_proxy_mcu 8>, + <&secure_proxy_mcu 6>, + <&secure_proxy_mcu 5>; mbox-names = "tx", "rx", "notify"; ti,host-id = <4>; ti,secure-host;
Signature · 1 line
2.43.0
PATCH 3/26 arm: dts: k3-am654-r5: Merge board file and U-Boot overlay
In reply to Bryan BrattlofThe R5 board file for U-Boot should be the same as the board file copied from Linux with a few alterations to work with the R5's view of the SoC.
First we need to unify the R5 board file and it's U-Boot overlay before we can unify the Linux board file with this one.
--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 1 - .../dts/k3-am654-r5-base-board-u-boot.dtsi | 208 ------------------ arch/arm/dts/k3-am654-r5-base-board.dts | 124 ++++++++++- 3 files changed, 119 insertions(+), 214 deletions(-) delete mode 100644 arch/arm/dts/k3-am654-r5-base-board-u-boot.dtsi
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +0 -1
@@ -3,7 +3,6 @@ * Copyright (C) 2018-2021 Texas Instruments Incorporated - https://www.ti.com/ */ -#include "k3-am654-r5-base-board-u-boot.dtsi" #include "k3-am65x-binman.dtsi" &pru0_0 {
arch/arm/dts/k3-am654-r5-base-board-u-boot.dtsi deleted +0 -208
208 lines not on this page · raw message
arch/arm/dts/k3-am654-r5-base-board.dts +119 -5
231 lines not on this page · raw message
Signature · 1 line
2.43.0
PATCH 21/26 arm: dts: k3-am654: remove duplicate vtt pinmux
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate vtt_pinmux node. Remove it
--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 2 +- arch/arm/dts/k3-am654-r5-base-board.dts | 10 ---------- 2 files changed, 1 insertion(+), 11 deletions(-)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +1 -1
@@ -101,7 +101,7 @@ bootph-pre-ram; }; -&wkup_vtt_pins_default { +&ddr_vtt_pins_default { bootph-pre-ram; };
arch/arm/dts/k3-am654-r5-base-board.dts +0 -10
@@ -101,18 +101,8 @@ vdd-supply-4 = <&vdd_mpu>; }; -&wkup_pmx0 { - wkup_vtt_pins_default: wkup_vtt_pins_default { - pinctrl-single,pins = < - AM65X_WKUP_IOPAD(0x0040, PIN_OUTPUT_PULLUP, 7) /* WKUP_GPIO0_28 */ - >; - }; -}; - &memorycontroller { vtt-supply = <&vtt_supply>; - pinctrl-names = "default"; - pinctrl-0 = <&wkup_vtt_pins_default>; }; /* MMC is probed to pull in firmware, so any clock
Signature · 1 line
2.43.0
PATCH 15/26 arm: dts: k3-am654: remove duplicate sdhci0 pinmux node
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate sdhci0 pinmux node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 25 +++++++------------------ 1 file changed, 7 insertions(+), 18 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +7 -18
@@ -137,22 +137,6 @@ }; &main_pmx0 { - main_mmc0_pins_default: main_mmc0_pins_default { - pinctrl-single,pins = < - AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */ - AM65X_IOPAD(0x01aC, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */ - AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */ - AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */ - AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */ - AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */ - AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */ - AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */ - AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */ - AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */ - AM65X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */ - >; - }; - main_mmc1_pins_default: main_mmc1_pins_default { pinctrl-single,pins = < AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
@@ -179,12 +163,17 @@ pinctrl-0 = <&wkup_vtt_pins_default>; }; +/* MMC is probed to pull in firmware, so any clock + * or power-domain operation will fail as we do not + * have the firmware running at this point. Delete the + * power-domain properties to avoid making calls to + * SYSFW before it is loaded. Public ROM has already + * set it up for us anyway. + */ &sdhci0 { clock-names = "clk_xin"; clocks = <&clk_200mhz>; - pinctrl-0 = <&main_mmc0_pins_default>; /delete-property/ power-domains; - ti,driver-strength-ohm = <50>; }; &sdhci1 {
Signature · 1 line
2.43.0
PATCH 16/26 arm: dts: k3-am654: remove duplicate sdhci1 pinmux node
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate sdhci1 pinmux node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 22 +++++++--------------- 1 file changed, 7 insertions(+), 15 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +7 -15
@@ -137,19 +137,6 @@ }; &main_pmx0 { - main_mmc1_pins_default: main_mmc1_pins_default { - pinctrl-single,pins = < - AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */ - AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */ - AM65X_IOPAD(0x02d0, PIN_INPUT_PULLUP, 0) /* (D28) MMC1_DAT0 */ - AM65X_IOPAD(0x02cc, PIN_INPUT_PULLUP, 0) /* (E27) MMC1_DAT1 */ - AM65X_IOPAD(0x02c8, PIN_INPUT_PULLUP, 0) /* (D26) MMC1_DAT2 */ - AM65X_IOPAD(0x02c4, PIN_INPUT_PULLUP, 0) /* (D27) MMC1_DAT3 */ - AM65X_IOPAD(0x02dc, PIN_INPUT_PULLUP, 0) /* (B24) MMC1_SDCD */ - AM65X_IOPAD(0x02e0, PIN_INPUT, 0) /* (C24) MMC1_SDWP */ - >; - }; - usb0_pins_default: usb0_pins_default { pinctrl-single,pins = < AM65X_IOPAD(0x02bc, PIN_OUTPUT, 0) /* (AD9) USB0_DRVVBUS */
@@ -176,12 +163,17 @@ /delete-property/ power-domains; }; +/* MMC is probed to pull in firmware, so any clock + * or power-domain operation will fail as we do not + * have the firmware running at this point. Delete the + * power-domain properties to avoid making calls to + * SYSFW before it is loaded. Public ROM has already + * set it up for us anyway. + */ &sdhci1 { clock-names = "clk_xin"; clocks = <&clk_200mhz>; - pinctrl-0 = <&main_mmc1_pins_default>; /delete-property/ power-domains; - ti,driver-strength-ohm = <50>; }; &wkup_i2c0 {
Signature · 1 line
2.43.0
PATCH 13/26 arm: dts: k3-am654: remove duplicate mcu_uart0 node
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified we now have a duplicate mcu_uart0 node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 12 ------------ 1 file changed, 12 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -12
@@ -18,7 +18,6 @@ ethernet0 = &cpsw_port1; remoteproc0 = &sysctrler; remoteproc1 = &a53_0; - serial1 = &mcu_uart0; serial2 = &main_uart0; spi0 = &ospi0; spi1 = &ospi1;
@@ -96,8 +95,6 @@ }; &mcu_uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&mcu_uart0_pins_default>; clock-frequency = <48000000>; /delete-property/ power-domains; status = "okay";
@@ -123,15 +120,6 @@ >; }; - mcu_uart0_pins_default: mcu_uart0_pins_default { - pinctrl-single,pins = < - AM65X_WKUP_IOPAD(0x0044, PIN_INPUT, 4) /* (P4) MCU_OSPI1_D1.MCU_UART0_RXD */ - AM65X_WKUP_IOPAD(0x0048, PIN_OUTPUT, 4) /* (P5) MCU_OSPI1_D2.MCU_UART0_TXD */ - AM65X_WKUP_IOPAD(0x004C, PIN_INPUT, 4) /* (P1) MCU_OSPI1_D3.MCU_UART0_CTSn */ - AM65X_WKUP_IOPAD(0x0054, PIN_OUTPUT, 4) /* (N3) MCU_OSPI1_CSn1.MCU_UART0_RTSn */ - >; - }; - wkup_i2c0_pins_default: wkup-i2c0-pins-default { pinctrl-single,pins = < AM65X_WKUP_IOPAD(0x00e0, PIN_INPUT, 0) /* (AC7) WKUP_I2C0_SCL */
Signature · 1 line
2.43.0
PATCH 2/26 configs: am65x_evm_a53: disable CONSOLE_MUX
In reply to Bryan BrattlofWe do not have a need to share a single console with the evaluation board and disabling this option reduces the complexity of configuring the consoles. Disable CONSOLE_MUX
--- configs/am65x_evm_a53_defconfig | 1 - 1 file changed, 1 deletion(-)
configs/am65x_evm_a53_defconfig +0 -1
@@ -36,7 +36,6 @@ CONFIG_DISTRO_DEFAULTS=y CONFIG_OF_SYSTEM_SETUP=y CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd; run init_${boot}; run boot_rprocs; if test ${boot_fit} -eq 1; then run get_fit_${boot}; run get_overlaystring; run run_fit; else; run get_kern_${boot}; run get_fdt_${boot}; run get_overlay_${boot}; run run_kern; fi;" CONFIG_LOGLEVEL=7 -CONFIG_CONSOLE_MUX=y CONFIG_SPL_MAX_SIZE=0x58000 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y CONFIG_SPL_BSS_START_ADDR=0x80a00000
Signature · 1 line
2.43.0
PATCH 9/26 arm: dts: k3-am654: remove duplicate timer
In reply to Bryan Brattloftimer1 is really just the mcu_timer0 node redefined for the WKUP SPL. Remove the timer1 and replace it with the mcu_timer0 from the Linux device tree we imported into U-Boot.
--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 12 ++++++++ arch/arm/dts/k3-am654-r5-base-board.dts | 29 ++++++++++---------- 2 files changed, 26 insertions(+), 15 deletions(-)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +12 -0
@@ -5,6 +5,18 @@ #include "k3-am65x-binman.dtsi" +/ { + chosen { + tick-timer = &mcu_timer0; + }; +}; + +&mcu_timer0 { + ti,timer-alwon; + clock-frequency = <25000000>; + bootph-all; +}; + &vtt_supply { bootph-pre-ram; };
arch/arm/dts/k3-am654-r5-base-board.dts +14 -15
@@ -26,11 +26,6 @@ usb1 = &usb1; }; - chosen { - stdout-path = "serial2:115200n8"; - tick-timer = &timer1; - }; - a53_0: a53@0 { compatible = "ti,am654-rproc"; reg = <0x0 0x00a90000 0x0 0x10>;
@@ -47,16 +42,6 @@ }; }; -&cbass_main { - timer1: timer@40400000 { - compatible = "ti,omap5430-timer"; - reg = <0x0 0x40400000 0x0 0x80>; - ti,timer-alwon; - clock-frequency = <25000000>; - bootph-all; - }; -}; - &cbass_mcu { mcu_secproxy: secproxy@28380000 { compatible = "ti,am654-secure-proxy";
@@ -108,6 +93,20 @@ }; }; +/* timer init is called as part of rproc_start() while + * starting System Firmware, so any clock/power-domain + * operations will fail as SYSFW is not yet up and running. + * Delete all clock/power-domain properties to avoid + * timer init failure. + * This is an always on timer at 20MHz. + */ +&mcu_timer0 { + /delete-property/ clocks; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + /delete-property/ power-domains; +}; + &dmsc { mboxes= <&mcu_secproxy 8>, <&mcu_secproxy 6>, <&mcu_secproxy 5>; mbox-names = "tx", "rx", "notify";
Signature · 1 line
2.43.0
PATCH 26/26 arm: dts: k3-am654: convert bootph-pre-ram to bootph-all
In reply to Bryan BrattlofMany nodes are reused between WKUP SPL, MAIN SPL, and U-Boot. Using bootph-pre-ram is causing these nodes to be present in SPL builds but pruned away during the U-Boot build. Convert these nodes to bootph-all so they will remain no matter which dtb build is happening.
--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 78 ++++++++++---------- 1 file changed, 39 insertions(+), 39 deletions(-)
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +39 -39
@@ -18,159 +18,159 @@ }; &vtt_supply { - bootph-pre-ram; + bootph-all; }; &cbass_main { - bootph-pre-ram; + bootph-all; }; &main_navss { - bootph-pre-ram; + bootph-all; }; &cbass_mcu { - bootph-pre-ram; + bootph-all; }; &mcu_navss { - bootph-pre-ram; + bootph-all; }; &mcu_ringacc { - bootph-pre-ram; + bootph-all; }; &mcu_udmap { - bootph-pre-ram; + bootph-all; }; &wkup_gpio0 { - bootph-pre-ram; + bootph-all; }; &secure_proxy_main { - bootph-pre-ram; + bootph-all; }; &cbass_wakeup { - bootph-pre-ram; + bootph-all; chipid@43000014 { - bootph-pre-ram; + bootph-all; }; }; &dmsc { - bootph-pre-ram; + bootph-all; }; &k3_pds { - bootph-pre-ram; + bootph-all; }; &k3_clks { - bootph-pre-ram; + bootph-all; }; &k3_reset { - bootph-pre-ram; + bootph-all; }; &wkup_uart0 { - bootph-pre-ram; + bootph-all; }; &mcu_uart0 { - bootph-pre-ram; + bootph-all; }; &main_uart0 { - bootph-pre-ram; + bootph-all; }; &wkup_vtm0 { - bootph-pre-ram; + bootph-all; }; &wkup_pmx0 { - bootph-pre-ram; + bootph-all; }; &wkup_uart0_pins_default { - bootph-pre-ram; + bootph-all; }; &ddr_vtt_pins_default { - bootph-pre-ram; + bootph-all; }; &mcu_uart0_pins_default { - bootph-pre-ram; + bootph-all; }; &wkup_i2c0_pins_default { - bootph-pre-ram; + bootph-all; }; &mcu_fss0_ospi0_pins_default { - bootph-pre-ram; + bootph-all; }; &main_pmx0 { - bootph-pre-ram; + bootph-all; }; &main_uart0_pins_default { - bootph-pre-ram; + bootph-all; }; &main_mmc0_pins_default { - bootph-pre-ram; + bootph-all; }; &main_mmc1_pins_default { - bootph-pre-ram; + bootph-all; }; &main_pmx1 { - bootph-pre-ram; + bootph-all; }; &sdhci0 { - bootph-pre-ram; + bootph-all; }; &sdhci1 { - bootph-pre-ram; + bootph-all; }; &wkup_i2c0 { - bootph-pre-ram; + bootph-all; }; &vdd_mpu { - bootph-pre-ram; + bootph-all; }; &ospi0 { - bootph-pre-ram; + bootph-all; flash@0 { - bootph-pre-ram; + bootph-all; }; }; &dwc3_0 { - bootph-pre-ram; + bootph-all; }; &scm_conf { - bootph-pre-ram; + bootph-all; }; &fss { - bootph-pre-ram; + bootph-all; }; &pru0_0 {
Signature · 1 line
2.43.0
PATCH 1/26 configs: am65x_evm_r5: enable driver for fixed regulators
In reply to Bryan BrattlofSome of the regulators we need to successfully boot are fixed regulators. Enable the driver to properly probe them.
--- configs/am65x_evm_r5_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/am65x_evm_r5_defconfig +2 -0
@@ -118,6 +118,8 @@ CONFIG_POWER_DOMAIN=y CONFIG_TI_SCI_POWER_DOMAIN=y CONFIG_DM_REGULATOR=y CONFIG_SPL_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_SPL_DM_REGULATOR_FIXED=y CONFIG_DM_REGULATOR_GPIO=y CONFIG_SPL_DM_REGULATOR_GPIO=y CONFIG_DM_REGULATOR_TPS62360=y
Signature · 1 line
2.43.0
PATCH 17/26 arm: dts: k3-am654: remove duplicate wkup_i2c0
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate wkup_i2c0 node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 25 ------------------------- 1 file changed, 25 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -25
@@ -112,13 +112,6 @@ >; }; - wkup_i2c0_pins_default: wkup-i2c0-pins-default { - pinctrl-single,pins = < - AM65X_WKUP_IOPAD(0x00e0, PIN_INPUT, 0) /* (AC7) WKUP_I2C0_SCL */ - AM65X_WKUP_IOPAD(0x00e4, PIN_INPUT, 0) /* (AD6) WKUP_I2C0_SDA */ - >; - }; - mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins_default { pinctrl-single,pins = < AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* (V1) MCU_OSPI0_CLK */
@@ -176,24 +169,6 @@ /delete-property/ power-domains; }; -&wkup_i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&wkup_i2c0_pins_default>; - clock-frequency = <400000>; - - vdd_mpu: tps62363@60 { - compatible = "ti,tps62363"; - reg = <0x60>; - regulator-name = "VDD_MPU"; - regulator-min-microvolt = <500000>; - regulator-max-microvolt = <1770000>; - regulator-always-on; - regulator-boot-on; - ti,vsel0-state-high; - ti,vsel1-state-high; - }; -}; - &ospi0 { pinctrl-names = "default"; pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
Signature · 1 line
2.43.0
PATCH 20/26 arm: dts: k3-am654: remove duplicate mdio
In reply to Bryan BrattlofWith the Linux and U-Boot board dtb files unified, we now have a duplicate mdio node. Remove it
--- arch/arm/dts/k3-am654-r5-base-board.dts | 9 --------- 1 file changed, 9 deletions(-)
arch/arm/dts/k3-am654-r5-base-board.dts +0 -9
@@ -154,15 +154,6 @@ /delete-property/ assigned-clock-parents; }; -&davinci_mdio { - phy0: ethernet-phy@0 { - reg = <0>; - /* TODO: phy reset: TCA9555RTWR(i2c:0x21)[p04].GPIO_MCU_RGMII_RSTN */ - ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; - ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; - }; -}; - &mcu_cpsw { reg = <0x0 0x46000000 0x0 0x200000>, <0x0 0x40f00200 0x0 0x2>;
Signature · 1 line
2.43.0
Quoted 10 lines · Bryan Brattlof
Hello Everyone!
This series gets the am65x booting again along with syncing the device tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64 files to make future syncs from Linux much easier. In the end the DTBs should look a lot like what the DTBs look like for the am64x which is fairly similar to the am65x.
Quoted 5 lines
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bcThanks for reviewing and happy holidays
~Bryan
For the series,
Nishanth, does this path work for you?
Signature · 1 line
Tom
Re: [PATCH 12/26] arm: dts: k3-am654: add needed regs to udmap nodes
In reply to Bryan BrattlofQuoted 20 lines · Bryan Brattlof
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate. However there are a few missing registers ranges in the udmap nodes need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however they have not made it to a Linux tag. To keep DMA operational until the next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a note for our future selves.
[0] https://lore.kernel.org/r/[email protected]
Signed-off-by Bryan Brattlof <[email protected]>--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 32 ++++++++++++++++++++ 1 file changed, 32 insertions(+)arch/arm/dts/k3-am654-base-board-u-boot.dtsi +0
-0
arch/arm/dts/k3-am654-base-board-u-boot.dtsi line 268
Quoted 9 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +6
-0@@ -260,3 +260,35 @@ &mcu_r5fss0 { ti,cluster-mode = <0>; }; + +/* The DMA driver requires a few extra register ranges + * which are missing for the am65x. A patch has been + * sent and will be synced after the v6.8-rc1 linux + * tag is published + */
Please fix multi-line comment style:
/*
* blah blah
*/
instead of
/* blah blah
* more stuff
*/
Quoted 6 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +6
-0+&main_udmap { + reg = <0x0 0x31150000 0x0 0x100>, + <0x0 0x34000000 0x0 0x100000>, + <0x0 0x35000000 0x0 0x100000>, + <0x0 0x30b00000 0x0 0x10000>, + <0x0 0x30c00000 0x0 0x10000>,
arch/arm/dts/k3-am654-base-board-u-boot.dtsi line 284
Quoted 10 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +10
-0+ <0x0 0x30d00000 0x0 0x8000>; + reg-names = "gcfg", "rchanrt", "tchanrt", + "tchan", "rchan", "rflow"; +}; + +/* The DMA driver requires a few extra register ranges + * which are missing for the am65x. A patch has been + * sent and will be synced after the v6.8-rc1 linux + * tag is published + */
and here.
Quoted 13 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +10
-0+&mcu_udmap { + reg = <0x0 0x285c0000 0x0 0x100>, + <0x0 0x2a800000 0x0 0x40000>, + <0x0 0x2aa00000 0x0 0x40000>, + <0x0 0x284a0000 0x0 0x4000>, + <0x0 0x284c0000 0x0 0x4000>, + <0x0 0x28400000 0x0 0x2000>; + reg-names = "gcfg", "rchanrt", "tchanrt", + "tchan", "rchan", "rflow"; +};Signature · 1 line
2.43.0
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH 26/26] arm: dts: k3-am654: convert bootph-pre-ram to bootph-all
In reply to Bryan BrattlofOn 11:44-20231221, Bryan Brattlof wrote:
[..]
Quoted 4 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +0
-0
[...]
arch/arm/dts/k3-am654-base-board-u-boot.dtsi line 22
Quoted 4 lines
&wkup_uart0{arch/arm/dts/k3-am654-base-board-u-boot.dtsi +1
-1- bootph-pre-ram; + bootph-all; };
Consider moving this to r5 dts - there is no use in having this in u-boot. should be pre-ram?
arch/arm/dts/k3-am654-base-board-u-boot.dtsi line 22
Quoted 5 lines
&mcu_uart0{arch/arm/dts/k3-am654-base-board-u-boot.dtsi +1
-1- bootph-pre-ram; + bootph-all; };
Same here:
Consider moving this to r5 dts - there is no use in having this in u-boot. should be pre-ram?
[...]
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH 15/26] arm: dts: k3-am654: remove duplicate sdhci0 pinmux node
In reply to Bryan BrattlofQuoted 36 lines · Bryan Brattlof
With the Linux and U-Boot board dtb files unified, we now have a duplicate sdhci0 pinmux node. Remove it
Signed-off-by Bryan Brattlof <[email protected]>--- arch/arm/dts/k3-am654-r5-base-board.dts | 25 +++++++------------------ 1 file changed, 7 insertions(+), 18 deletions(-)arch/arm/dts/k3-am654-r5-base-board.dts +0
-16@@ -137,22 +137,6 @@ }; &main_pmx0 { - main_mmc0_pins_default: main_mmc0_pins_default { - pinctrl-single,pins = < - AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */ - AM65X_IOPAD(0x01aC, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */ - AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */ - AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */ - AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */ - AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */ - AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */ - AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */ - AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */ - AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */ - AM65X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */ - >; - }; - main_mmc1_pins_default: main_mmc1_pins_default { pinctrl-single,pins = < AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
arch/arm/dts/k3-am654-r5-base-board.dts line 172
Quoted 10 lines
arch/arm/dts/k3-am654-r5-base-board.dts +7
-0@@ -179,12 +163,17 @@ pinctrl-0 = <&wkup_vtt_pins_default>; }; +/* MMC is probed to pull in firmware, so any clock + * or power-domain operation will fail as we do not + * have the firmware running at this point. Delete the + * power-domain properties to avoid making calls to + * SYSFW before it is loaded. Public ROM has already + * set it up for us anyway. + */
Please fix your comment style here:
/*
* blah blah
*/
Quoted 12 lines
arch/arm/dts/k3-am654-r5-base-board.dts +0
-2&sdhci0 { clock-names = "clk_xin"; clocks = <&clk_200mhz>; - pinctrl-0 = <&main_mmc0_pins_default>; /delete-property/ power-domains; - ti,driver-strength-ohm = <50>; }; &sdhci1 {Signature · 1 line
2.43.0
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH 16/26] arm: dts: k3-am654: remove duplicate sdhci1 pinmux node
In reply to Bryan BrattlofQuoted 33 lines · Bryan Brattlof
With the Linux and U-Boot board dtb files unified, we now have a duplicate sdhci1 pinmux node. Remove it
Signed-off-by Bryan Brattlof <[email protected]>--- arch/arm/dts/k3-am654-r5-base-board.dts | 22 +++++++--------------- 1 file changed, 7 insertions(+), 15 deletions(-)arch/arm/dts/k3-am654-r5-base-board.dts +0
-13@@ -137,19 +137,6 @@ }; &main_pmx0 { - main_mmc1_pins_default: main_mmc1_pins_default { - pinctrl-single,pins = < - AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */ - AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */ - AM65X_IOPAD(0x02d0, PIN_INPUT_PULLUP, 0) /* (D28) MMC1_DAT0 */ - AM65X_IOPAD(0x02cc, PIN_INPUT_PULLUP, 0) /* (E27) MMC1_DAT1 */ - AM65X_IOPAD(0x02c8, PIN_INPUT_PULLUP, 0) /* (D26) MMC1_DAT2 */ - AM65X_IOPAD(0x02c4, PIN_INPUT_PULLUP, 0) /* (D27) MMC1_DAT3 */ - AM65X_IOPAD(0x02dc, PIN_INPUT_PULLUP, 0) /* (B24) MMC1_SDCD */ - AM65X_IOPAD(0x02e0, PIN_INPUT, 0) /* (C24) MMC1_SDWP */ - >; - }; - usb0_pins_default: usb0_pins_default { pinctrl-single,pins = < AM65X_IOPAD(0x02bc, PIN_OUTPUT, 0) /* (AD9) USB0_DRVVBUS */
arch/arm/dts/k3-am654-r5-base-board.dts line 172
Quoted 10 lines
arch/arm/dts/k3-am654-r5-base-board.dts +7
-0@@ -176,12 +163,17 @@ /delete-property/ power-domains; }; +/* MMC is probed to pull in firmware, so any clock + * or power-domain operation will fail as we do not + * have the firmware running at this point. Delete the + * power-domain properties to avoid making calls to + * SYSFW before it is loaded. Public ROM has already + * set it up for us anyway. + */
Same - please fix the comment style here as well.
Quoted 12 lines
arch/arm/dts/k3-am654-r5-base-board.dts +0
-2&sdhci1 { clock-names = "clk_xin"; clocks = <&clk_200mhz>; - pinctrl-0 = <&main_mmc1_pins_default>; /delete-property/ power-domains; - ti,driver-strength-ohm = <50>; }; &wkup_i2c0 {Signature · 1 line
2.43.0
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Quoted 15 lines · Tom Rini
Quoted 13 lines · Bryan Brattlof
Hello Everyone!
This series gets the am65x booting again along with syncing the device tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64 files to make future syncs from Linux much easier. In the end the DTBs should look a lot like what the DTBs look like for the am64x which is fairly similar to the am65x.
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bc
Quoted 8 lines
Quoted 2 lines
Thanks for reviewing and happy holidays
~BryanFor the series,
Tested-by Tom Rini <[email protected]>Nishanth, does this path work for you?
Other than the minor comments provided in the relevant patches,
The following files also need sync up with v6.7-rc1.
k3-am65-iot2050-common-pg2.dtsik3-am65-iot2050-common.dtsik3-am6528-iot2050-basic-common.dtsik3-am6548-iot2050-advanced-common.dtsik3-am6548-iot2050-advanced-m2.dts
Jan - could you look at syncing those once an update to this series is posted? We could probably have a smoother v6.8-rc1 from then on.
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Quoted 29 lines · Nishanth Menon
Quoted 15 lines · Tom Rini
Quoted 13 lines · Bryan Brattlof
Hello Everyone!
This series gets the am65x booting again along with syncing the device tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64 files to make future syncs from Linux much easier. In the end the DTBs should look a lot like what the DTBs look like for the am64x which is fairly similar to the am65x.
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bcQuoted 8 lines
Quoted 2 lines
Thanks for reviewing and happy holidays
~BryanFor the series,
Tested-by Tom Rini <[email protected]>Nishanth, does this path work for you?
Other than the minor comments provided in the relevant patches,
The following files also need sync up with v6.7-rc1.
Quoted 8 lines
k3-am65-iot2050-common-pg2.dtsik3-am65-iot2050-common.dtsik3-am6528-iot2050-basic-common.dtsik3-am6548-iot2050-advanced-common.dtsik3-am6548-iot2050-advanced-m2.dtsJan - could you look at syncing those once an update to this series is posted? We could probably have a smoother v6.8-rc1 from then on.
I hope that by v6.8-rc1 time we'll have merged Sumit's patch series and so instead TI platforms will move to the v6.7-dts tag there, and then v6.8-dts once that's out.
Signature · 1 line
Tom
Re: [PATCH 12/26] arm: dts: k3-am654: add needed regs to udmap nodes
In reply to Nishanth MenonOn December 27, 2023 thus sayeth Nishanth Menon:
Quoted 31 lines · Bryan Brattlof
Quoted 20 lines
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate. However there are a few missing registers ranges in the udmap nodes need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however they have not made it to a Linux tag. To keep DMA operational until the next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a note for our future selves.
[0] https://lore.kernel.org/r/[email protected]
Signed-off-by Bryan Brattlof <[email protected]>--- arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 32 ++++++++++++++++++++ 1 file changed, 32 insertions(+)arch/arm/dts/k3-am654-base-board-u-boot.dtsi +0
-0arch/arm/dts/k3-am654-base-board-u-boot.dtsi line 268
Quoted 9 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +6
-0@@ -260,3 +260,35 @@ &mcu_r5fss0 { ti,cluster-mode = <0>; }; + +/* The DMA driver requires a few extra register ranges + * which are missing for the am65x. A patch has been + * sent and will be synced after the v6.8-rc1 linux + * tag is published + */
Quoted 8 lines
Please fix multi-line comment style:
/*
* blah blah
*/
instead of
/* blah blah
* more stuff
*/
Ah yeah I can get all of the comments fixed up.
~Bryan
Quoted 37 lines
Quoted 6 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +6
-0+&main_udmap { + reg = <0x0 0x31150000 0x0 0x100>, + <0x0 0x34000000 0x0 0x100000>, + <0x0 0x35000000 0x0 0x100000>, + <0x0 0x30b00000 0x0 0x10000>, + <0x0 0x30c00000 0x0 0x10000>,arch/arm/dts/k3-am654-base-board-u-boot.dtsi line 284
Quoted 10 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +10
-0+ <0x0 0x30d00000 0x0 0x8000>; + reg-names = "gcfg", "rchanrt", "tchanrt", + "tchan", "rchan", "rflow"; +}; + +/* The DMA driver requires a few extra register ranges + * which are missing for the am65x. A patch has been + * sent and will be synced after the v6.8-rc1 linux + * tag is published + */and here.
Quoted 13 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +10
-0+&mcu_udmap { + reg = <0x0 0x285c0000 0x0 0x100>, + <0x0 0x2a800000 0x0 0x40000>, + <0x0 0x2aa00000 0x0 0x40000>, + <0x0 0x284a0000 0x0 0x4000>, + <0x0 0x284c0000 0x0 0x4000>, + <0x0 0x28400000 0x0 0x2000>; + reg-names = "gcfg", "rchanrt", "tchanrt", + "tchan", "rchan", "rflow"; +};Signature · 1 line
2.43.0Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH 26/26] arm: dts: k3-am654: convert bootph-pre-ram to bootph-all
In reply to Nishanth MenonOn December 27, 2023 thus sayeth Nishanth Menon:
Quoted 16 lines · Bryan Brattlof
[..]
Quoted 4 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi +0
-0[...]
arch/arm/dts/k3-am654-base-board-u-boot.dtsi line 22
Quoted 4 lines
&wkup_uart0{arch/arm/dts/k3-am654-base-board-u-boot.dtsi +1
-1- bootph-pre-ram; + bootph-all; };Consider moving this to r5 dts - there is no use in having this in u-boot. should be pre-ram?
Quoted 1 line
Quoted 8 lines
arch/arm/dts/k3-am654-base-board-u-boot.dtsi line 22
Quoted 4 lines
&mcu_uart0{arch/arm/dts/k3-am654-base-board-u-boot.dtsi +1
-1- bootph-pre-ram; + bootph-all; };Same here:
Consider moving this to r5 dts - there is no use in having this in u-boot. should be pre-ram?
Oh good idea. I'll move these to the r5 dts
~Bryan
Quoted 29 lines · Nishanth Menon
Quoted 15 lines · Tom Rini
Quoted 13 lines · Bryan Brattlof
Hello Everyone!
This series gets the am65x booting again along with syncing the device tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64 files to make future syncs from Linux much easier. In the end the DTBs should look a lot like what the DTBs look like for the am64x which is fairly similar to the am65x.
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bcQuoted 8 lines
Quoted 2 lines
Thanks for reviewing and happy holidays
~BryanFor the series,
Tested-by Tom Rini <[email protected]>Nishanth, does this path work for you?
Other than the minor comments provided in the relevant patches,
The following files also need sync up with v6.7-rc1.
Quoted 9 lines
k3-am65-iot2050-common-pg2.dtsik3-am65-iot2050-common.dtsik3-am6528-iot2050-basic-common.dtsik3-am6548-iot2050-advanced-common.dtsik3-am6548-iot2050-advanced-m2.dtsJan - could you look at syncing those once an update to this series is posted? We could probably have a smoother v6.8-rc1 from then on.
We currently plan to sync once support for the new SM variant is in the upstream DT. Do you see other changes that would benefit from an earlier sync?
Jan
Signature · 2 lines
Siemens AG, Technology Linux Expert Center
Quoted 36 lines · Jan Kiszka
Quoted 35 lines · Nishanth Menon
Quoted 15 lines · Tom Rini
Quoted 13 lines · Bryan Brattlof
Hello Everyone!
This series gets the am65x booting again along with syncing the device tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64 files to make future syncs from Linux much easier. In the end the DTBs should look a lot like what the DTBs look like for the am64x which is fairly similar to the am65x.
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bcQuoted 8 lines
Quoted 2 lines
Thanks for reviewing and happy holidays
~BryanFor the series,
Tested-by Tom Rini <[email protected]>Nishanth, does this path work for you?
Other than the minor comments provided in the relevant patches,
The following files also need sync up with v6.7-rc1.
k3-am65-iot2050-common-pg2.dtsik3-am65-iot2050-common.dtsik3-am6528-iot2050-basic-common.dtsik3-am6548-iot2050-advanced-common.dtsik3-am6548-iot2050-advanced-m2.dts
Quoted 7 lines
Quoted 3 lines
Jan - could you look at syncing those once an update to this series is posted? We could probably have a smoother v6.8-rc1 from then on.
We currently plan to sync once support for the new SM variant is in the upstream DT. Do you see other changes that would benefit from an earlier sync?
So this sync is because the ref platforms at least do not boot, is iot2050 currently booting?
Signature · 1 line
Tom
Quoted 41 lines · Tom Rini
Quoted 40 lines · Jan Kiszka
Quoted 38 lines · Nishanth Menon
Quoted 15 lines · Tom Rini
Quoted 13 lines · Bryan Brattlof
Hello Everyone!
This series gets the am65x booting again along with syncing the device tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64 files to make future syncs from Linux much easier. In the end the DTBs should look a lot like what the DTBs look like for the am64x which is fairly similar to the am65x.
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bcQuoted 8 lines
Quoted 2 lines
Thanks for reviewing and happy holidays
~BryanFor the series,
Tested-by Tom Rini <[email protected]>Nishanth, does this path work for you?
Other than the minor comments provided in the relevant patches,
The following files also need sync up with v6.7-rc1.
k3-am65-iot2050-common-pg2.dtsik3-am65-iot2050-common.dtsik3-am6528-iot2050-basic-common.dtsik3-am6548-iot2050-advanced-common.dtsik3-am6548-iot2050-advanced-m2.dtsJan - could you look at syncing those once an update to this series is posted? We could probably have a smoother v6.8-rc1 from then on.
Quoted 6 lines
Quoted 3 lines
We currently plan to sync once support for the new SM variant is in the upstream DT. Do you see other changes that would benefit from an earlier sync?
So this sync is because the ref platforms at least do not boot, is iot2050 currently booting?
It was booting with ~v2024.01-rc4 before Christmas, didn't try latest master yet.
Jan
Signature · 2 lines
Siemens AG, Technology Linux Expert Center
Quoted 46 lines · Jan Kiszka
Quoted 45 lines · Tom Rini
Quoted 43 lines · Jan Kiszka
Quoted 29 lines · Nishanth Menon
Quoted 15 lines · Tom Rini
Quoted 13 lines · Bryan Brattlof
Hello Everyone!
This series gets the am65x booting again along with syncing the device tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64 files to make future syncs from Linux much easier. In the end the DTBs should look a lot like what the DTBs look like for the am64x which is fairly similar to the am65x.
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bcQuoted 8 lines
Quoted 2 lines
Thanks for reviewing and happy holidays
~BryanFor the series,
Tested-by Tom Rini <[email protected]>Nishanth, does this path work for you?
Other than the minor comments provided in the relevant patches,
The following files also need sync up with v6.7-rc1.
Quoted 9 lines
k3-am65-iot2050-common-pg2.dtsik3-am65-iot2050-common.dtsik3-am6528-iot2050-basic-common.dtsik3-am6548-iot2050-advanced-common.dtsik3-am6548-iot2050-advanced-m2.dtsJan - could you look at syncing those once an update to this series is posted? We could probably have a smoother v6.8-rc1 from then on.
We currently plan to sync once support for the new SM variant is in the upstream DT. Do you see other changes that would benefit from an earlier sync?
Quoted 5 lines
Quoted 2 lines
So this sync is because the ref platforms at least do not boot, is iot2050 currently booting?
It was booting with ~v2024.01-rc4 before Christmas, didn't try latest master yet.
OK, then it should still be fine but please do confirm if you have the cycles, thanks.
Signature · 1 line
Tom