Skip to contentSkip to conversation

Add NPCM8XX clock driver

PATCH Superseded Tomer Maimon 2 participants 8 messages Aug 27, 2024 – Sep 12, 2024

Subsystems (4)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
author maintainer
#2 lore raw

PATCH v3 2/3 reset: npcm: register npcm8xx clock auxiliary bus device

In reply to Tomer Maimon

Add NPCM8xx clock controller auxiliary bus device registration.

The NPCM8xx clock controller is registered as an aux device because the reset and the clock controller share the same register region.

---
 drivers/reset/Kconfig               |  1 +
 drivers/reset/reset-npcm.c          | 74 ++++++++++++++++++++++++++++-
 include/soc/nuvoton/clock-npcm8xx.h | 16 +++++++
 3 files changed, 90 insertions(+), 1 deletion(-)
 create mode 100644 include/soc/nuvoton/clock-npcm8xx.h
drivers/reset/Kconfig +1 -0
index ccd59ddd7610..531c9c6a7b54 100644
@@ -139,6 +139,7 @@ config RESET_MESON_AUDIO_ARB
 config RESET_NPCM
 	bool "NPCM BMC Reset Driver" if COMPILE_TEST
 	default ARCH_NPCM
+	select AUXILIARY_BUS
 	help
 	  This enables the reset controller driver for Nuvoton NPCM
 	  BMC SoCs.
drivers/reset/reset-npcm.c +73 -1

115 lines not on this page · raw message

include/soc/nuvoton/clock-npcm8xx.h new file +16 -0
new file mode 100644
index 000000000000..139130e98c51
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __SOC_NPCM8XX_CLOCK_H
+#define __SOC_NPCM8XX_CLOCK_H
+
+#include <linux/auxiliary_bus.h>
+#include <linux/container_of.h>
+
+struct npcm_clock_adev {
+	void __iomem *base;
+	struct auxiliary_device adev;
+};
+
+#define to_npcm_clock_adev(_adev) \
+	container_of((_adev), struct npcm_clock_adev, adev)
+
+#endif

--
2.34.1

Tomer Maimon

author maintainer
#0 lore raw

v3 cover Add NPCM8XX clock driver

This patchset adds clock support for the Nuvoton Arbel NPCM8XX Board Management controller (BMC) SoC family.

The NPCM8xx clock controller is created using the auxiliary device framework and set up in the npcm reset driver since the NPCM8xx clock is using the same register region.

This patchset based on NPCM8xx clock controller V27
https://patchwork.kernel.org/project/linux-clk/cover/[email protected]/

This patchset was tested on the Arbel NPCM8XX evaluation board.

Changes since version 2:
- Remove trailing whitespaces

Changes since version 1:
- Align with NPCM8xx clock controller V27.
- Remove patches that are not in the clock patchset.

Tomer Maimon (3):
dt-bindings: reset: npcm: add clock properties
reset: npcm: register npcm8xx clock auxiliary bus device
clk: npcm8xx: add clock controller

 .../bindings/reset/nuvoton,npcm750-reset.yaml |  18 +
 drivers/clk/Kconfig                           |   8 +
 drivers/clk/Makefile                          |   1 +
 drivers/clk/clk-npcm8xx.c                     | 429 ++++++++++++++++++
 drivers/reset/Kconfig                         |   1 +
 drivers/reset/reset-npcm.c                    |  74 ++-
 include/soc/nuvoton/clock-npcm8xx.h           |  16 +
 7 files changed, 546 insertions(+), 1 deletion(-)
 create mode 100644 drivers/clk/clk-npcm8xx.c
 create mode 100644 include/soc/nuvoton/clock-npcm8xx.h

--
2.34.1

author maintainer
#1 lore raw

PATCH v3 1/3 dt-bindings: reset: npcm: add clock properties

This commit adds a 25MHz reference clock and clock-cell properties to the NPCM reset document. The addition is necessitated by the integration of the NPCM8xx clock auxiliary bus device into the NPCM reset driver.

The inclusion of the NPCM8xx clock properties in the reset document is crucial as the reset block also serves as a clock provider for the NPCM8xx clock. This enhancement is intended to facilitate the use of the NPCM8xx clock driver.

---
 .../bindings/reset/nuvoton,npcm750-reset.yaml  | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
Documentation/devicetree/bindings/reset/nuvoton,npcm750-reset.yaml +18 -0
index d82e65e37cc0..72523f1bbc18 100644
@@ -21,6 +21,13 @@ properties:
   '#reset-cells':
     const: 2
 
+  '#clock-cells':
+    const: 1
+
+  clocks:
+    items:
+      - description: specify external 25MHz reference clock.
+
   nuvoton,sysgcr:
     $ref: /schemas/types.yaml#/definitions/phandle
     description: a phandle to access GCR registers.
@@ -39,6 +46,17 @@ required:
   - '#reset-cells'
   - nuvoton,sysgcr
 
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - nuvoton,npcm845-reset
+then:
+  required:
+    - '#clock-cells'
+    - clocks
+
 additionalProperties: false
 
 examples:

--
2.34.1

author maintainer
#3 lore raw

PATCH v3 3/3 clk: npcm8xx: add clock controller

In reply to Tomer Maimon

Add auxiliary driver to support Nuvoton Arbel BMC NPCM8XX contains an integrated clock controller which generates and supplies clocks to all modules within the BMC.

The NPCM8xx clock controller is created using the auxiliary device framework and set up in the npcm reset driver since the NPCM8xx clock is using the same register region.

---
 drivers/clk/Kconfig       |   8 +
 drivers/clk/Makefile      |   1 +
 drivers/clk/clk-npcm8xx.c | 429 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 438 insertions(+)
 create mode 100644 drivers/clk/clk-npcm8xx.c
drivers/clk/Kconfig +8 -0
index c30099866174..9bc5f2dfc7e2 100644
@@ -325,6 +325,14 @@ config COMMON_CLK_LOCHNAGAR
 	  This driver supports the clocking features of the Cirrus Logic
 	  Lochnagar audio development board.
 
+config COMMON_CLK_NPCM8XX
+	tristate "Clock driver for the NPCM8XX SoC Family"
+	depends on ARCH_NPCM || COMPILE_TEST
+	help
+	  This driver supports the clocks on the Nuvoton BMC NPCM8XX SoC Family,
+	  all the clocks are initialized by the bootloader, so this driver
+	  allows only reading of current settings directly from the hardware.
+
 config COMMON_CLK_LOONGSON2
 	bool "Clock driver for Loongson-2 SoC"
 	depends on LOONGARCH || COMPILE_TEST
drivers/clk/Makefile +1 -0
index 18969cbd4bb1..e2cbc6cceb8c 100644
@@ -51,6 +51,7 @@ obj-$(CONFIG_ARCH_MILBEAUT_M10V)	+= clk-milbeaut.o
 obj-$(CONFIG_ARCH_MOXART)		+= clk-moxart.o
 obj-$(CONFIG_ARCH_NOMADIK)		+= clk-nomadik.o
 obj-$(CONFIG_ARCH_NPCM7XX)	    	+= clk-npcm7xx.o
+obj-$(CONFIG_COMMON_CLK_NPCM8XX)	+= clk-npcm8xx.o
 obj-$(CONFIG_ARCH_NSPIRE)		+= clk-nspire.o
 obj-$(CONFIG_COMMON_CLK_PALMAS)		+= clk-palmas.o
 obj-$(CONFIG_CLK_LS1028A_PLLDIG)	+= clk-plldig.o
drivers/clk/clk-npcm8xx.c new file +429 -0

429 lines not on this page · raw message

--
2.34.1

maintainer
#4 lore raw

Re: [linux dev-6.6 v3 3/3] clk: npcm8xx: add clock controller

Quoted 10 lines · Tomer Maimon

Add auxiliary driver to support Nuvoton Arbel BMC NPCM8XX contains an integrated clock controller which generates and supplies clocks to all modules within the BMC.

The NPCM8xx clock controller is created using the auxiliary device framework and set up in the npcm reset driver since the NPCM8xx clock is using the same register region.

So checkpatch still warns on this one, though I think whitespace is less of a problem.

For what it's worth, here's the output I get:

Executing: ./scripts/checkpatch.pl --strict -g HEAD
WARNING: please write a help paragraph that fully describes the config symbol #33: FILE: drivers/clk/Kconfig:328:
+config COMMON_CLK_NPCM8XX

   +       tristate "Clock driver for the NPCM8XX SoC Family"
   +       depends on ARCH_NPCM || COMPILE_TEST
   +       help
   +         This driver supports the clocks on the Nuvoton BMC NPCM8XX SoC Family,
   +         all the clocks are initialized by the bootloader, so this driver
   +         allows only reading of current settings directly from the hardware.

+

WARNING: added, moved or deleted file(s), does MAINTAINERS need updating? #57:
new file mode 100644

WARNING: line length of 112 exceeds 100 columns #252: FILE: drivers/clk/clk-npcm8xx.c:191:
+ { NPCM8XX_CLKDIV1, 26, 2, "ahb", &hw_pre_clk, CLK_DIVIDER_READ_ONLY, CLK_IS_CRITICAL, NPCM8XX_CLK_AHB },

WARNING: line length of 137 exceeds 100 columns #257: FILE: drivers/clk/clk-npcm8xx.c:196:
+ { NPCM8XX_CLKDIV1, 28, 3, "adc", &npcm8xx_pre_divs[0].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_ADC },

WARNING: line length of 107 exceeds 100 columns #259: FILE: drivers/clk/clk-npcm8xx.c:198:
+ { NPCM8XX_CLKDIV1, 11, 5, "mmc", &npcm8xx_muxes[2].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_MMC },

WARNING: line length of 106 exceeds 100 columns #261: FILE: drivers/clk/clk-npcm8xx.c:200:
+ { NPCM8XX_CLKDIV1, 2, 4, "pci", &npcm8xx_muxes[7].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_PCI },

WARNING: line length of 139 exceeds 100 columns #263: FILE: drivers/clk/clk-npcm8xx.c:202:
+ { NPCM8XX_CLKDIV2, 30, 2, "apb4", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB4 },

WARNING: line length of 139 exceeds 100 columns #264: FILE: drivers/clk/clk-npcm8xx.c:203:
+ { NPCM8XX_CLKDIV2, 28, 2, "apb3", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB3 },

WARNING: line length of 139 exceeds 100 columns #265: FILE: drivers/clk/clk-npcm8xx.c:204:
+ { NPCM8XX_CLKDIV2, 26, 2, "apb2", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB2 },

WARNING: line length of 139 exceeds 100 columns #266: FILE: drivers/clk/clk-npcm8xx.c:205:
+ { NPCM8XX_CLKDIV2, 24, 2, "apb1", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB1 },

WARNING: line length of 139 exceeds 100 columns #267: FILE: drivers/clk/clk-npcm8xx.c:206:
+ { NPCM8XX_CLKDIV2, 22, 2, "apb5", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB5 },

WARNING: line length of 113 exceeds 100 columns #268: FILE: drivers/clk/clk-npcm8xx.c:207:
+ { NPCM8XX_CLKDIV2, 16, 5, "clkout", &npcm8xx_muxes[8].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_CLKOUT },

WARNING: line length of 107 exceeds 100 columns #269: FILE: drivers/clk/clk-npcm8xx.c:208:
+ { NPCM8XX_CLKDIV2, 13, 3, "gfx", &npcm8xx_muxes[7].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_GFX },

WARNING: line length of 112 exceeds 100 columns #270: FILE: drivers/clk/clk-npcm8xx.c:209:
+ { NPCM8XX_CLKDIV2, 8, 5, "usb_bridge", &npcm8xx_muxes[4].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SU },

WARNING: line length of 112 exceeds 100 columns #271: FILE: drivers/clk/clk-npcm8xx.c:210:
+ { NPCM8XX_CLKDIV2, 4, 4, "usb_host", &npcm8xx_muxes[4].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SU48 },

WARNING: line length of 108 exceeds 100 columns #272: FILE: drivers/clk/clk-npcm8xx.c:211:
+ { NPCM8XX_CLKDIV2, 0, 4, "sdhc", &npcm8xx_muxes[2].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SDHC },

WARNING: line length of 112 exceeds 100 columns #274: FILE: drivers/clk/clk-npcm8xx.c:213:
+ { NPCM8XX_CLKDIV3, 16, 8, "spi1", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SPI1 },

WARNING: line length of 111 exceeds 100 columns #275: FILE: drivers/clk/clk-npcm8xx.c:214:
+ { NPCM8XX_CLKDIV3, 11, 5, "uart2", &npcm8xx_muxes[3].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_UART2 },

WARNING: line length of 111 exceeds 100 columns #276: FILE: drivers/clk/clk-npcm8xx.c:215:
+ { NPCM8XX_CLKDIV3, 6, 5, "spi0", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SPI0 },

WARNING: line length of 111 exceeds 100 columns #277: FILE: drivers/clk/clk-npcm8xx.c:216:
+ { NPCM8XX_CLKDIV3, 1, 5, "spix", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SPIX },

WARNING: line length of 106 exceeds 100 columns #279: FILE: drivers/clk/clk-npcm8xx.c:218:
+ { NPCM8XX_CLKDIV4, 28, 4, "rg", &npcm8xx_muxes[11].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_RG },

WARNING: line length of 108 exceeds 100 columns #280: FILE: drivers/clk/clk-npcm8xx.c:219:
+ { NPCM8XX_CLKDIV4, 12, 4, "rcp", &npcm8xx_muxes[12].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_RCP },

WARNING: line length of 133 exceeds 100 columns #282: FILE: drivers/clk/clk-npcm8xx.c:221:
+ { NPCM8XX_THRTL_CNT, 0, 2, "th", &npcm8xx_muxes[0].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_TH },

WARNING: Prefer "GPL" over "GPL v2" - see commit bf7fbeeae6db ("module: Cure the MODULE_LICENSE "GPL" vs. "GPL v2" bogosity") #490: FILE: drivers/clk/clk-npcm8xx.c:429:
+MODULE_LICENSE("GPL v2");

total: 0 errors, 24 warnings, 0 checks, 450 lines checked

Andrew

author maintainer
#5 lore raw

Re: [linux dev-6.6 v3 3/3] clk: npcm8xx: add clock controller

Hi Andrew,

Thanks for your comments,

Send V4 with fixed exceed line length.

Tomer

Quoted 125 lines · Andrew Jeffery
Quoted 10 lines · Tomer Maimon

Add auxiliary driver to support Nuvoton Arbel BMC NPCM8XX contains an integrated clock controller which generates and supplies clocks to all modules within the BMC.

The NPCM8xx clock controller is created using the auxiliary device framework and set up in the npcm reset driver since the NPCM8xx clock is using the same register region.

So checkpatch still warns on this one, though I think whitespace is less of a problem.

For what it's worth, here's the output I get:

Executing: ./scripts/checkpatch.pl --strict -g HEAD
WARNING: please write a help paragraph that fully describes the config symbol #33: FILE: drivers/clk/Kconfig:328:
+config COMMON_CLK_NPCM8XX

   +       tristate "Clock driver for the NPCM8XX SoC Family"
   +       depends on ARCH_NPCM || COMPILE_TEST
   +       help
   +         This driver supports the clocks on the Nuvoton BMC NPCM8XX SoC Family,
   +         all the clocks are initialized by the bootloader, so this driver
   +         allows only reading of current settings directly from the hardware.

+

WARNING: added, moved or deleted file(s), does MAINTAINERS need updating? #57:
new file mode 100644

WARNING: line length of 112 exceeds 100 columns #252: FILE: drivers/clk/clk-npcm8xx.c:191:
+ { NPCM8XX_CLKDIV1, 26, 2, "ahb", &hw_pre_clk, CLK_DIVIDER_READ_ONLY, CLK_IS_CRITICAL, NPCM8XX_CLK_AHB },

WARNING: line length of 137 exceeds 100 columns #257: FILE: drivers/clk/clk-npcm8xx.c:196:
+ { NPCM8XX_CLKDIV1, 28, 3, "adc", &npcm8xx_pre_divs[0].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_ADC },

WARNING: line length of 107 exceeds 100 columns #259: FILE: drivers/clk/clk-npcm8xx.c:198:
+ { NPCM8XX_CLKDIV1, 11, 5, "mmc", &npcm8xx_muxes[2].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_MMC },

WARNING: line length of 106 exceeds 100 columns #261: FILE: drivers/clk/clk-npcm8xx.c:200:
+ { NPCM8XX_CLKDIV1, 2, 4, "pci", &npcm8xx_muxes[7].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_PCI },

WARNING: line length of 139 exceeds 100 columns #263: FILE: drivers/clk/clk-npcm8xx.c:202:
+ { NPCM8XX_CLKDIV2, 30, 2, "apb4", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB4 },

WARNING: line length of 139 exceeds 100 columns #264: FILE: drivers/clk/clk-npcm8xx.c:203:
+ { NPCM8XX_CLKDIV2, 28, 2, "apb3", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB3 },

WARNING: line length of 139 exceeds 100 columns #265: FILE: drivers/clk/clk-npcm8xx.c:204:
+ { NPCM8XX_CLKDIV2, 26, 2, "apb2", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB2 },

WARNING: line length of 139 exceeds 100 columns #266: FILE: drivers/clk/clk-npcm8xx.c:205:
+ { NPCM8XX_CLKDIV2, 24, 2, "apb1", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB1 },

WARNING: line length of 139 exceeds 100 columns #267: FILE: drivers/clk/clk-npcm8xx.c:206:
+ { NPCM8XX_CLKDIV2, 22, 2, "apb5", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB5 },

WARNING: line length of 113 exceeds 100 columns #268: FILE: drivers/clk/clk-npcm8xx.c:207:
+ { NPCM8XX_CLKDIV2, 16, 5, "clkout", &npcm8xx_muxes[8].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_CLKOUT },

WARNING: line length of 107 exceeds 100 columns #269: FILE: drivers/clk/clk-npcm8xx.c:208:
+ { NPCM8XX_CLKDIV2, 13, 3, "gfx", &npcm8xx_muxes[7].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_GFX },

WARNING: line length of 112 exceeds 100 columns #270: FILE: drivers/clk/clk-npcm8xx.c:209:
+ { NPCM8XX_CLKDIV2, 8, 5, "usb_bridge", &npcm8xx_muxes[4].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SU },

WARNING: line length of 112 exceeds 100 columns #271: FILE: drivers/clk/clk-npcm8xx.c:210:
+ { NPCM8XX_CLKDIV2, 4, 4, "usb_host", &npcm8xx_muxes[4].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SU48 },

WARNING: line length of 108 exceeds 100 columns #272: FILE: drivers/clk/clk-npcm8xx.c:211:
+ { NPCM8XX_CLKDIV2, 0, 4, "sdhc", &npcm8xx_muxes[2].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SDHC },

WARNING: line length of 112 exceeds 100 columns #274: FILE: drivers/clk/clk-npcm8xx.c:213:
+ { NPCM8XX_CLKDIV3, 16, 8, "spi1", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SPI1 },

WARNING: line length of 111 exceeds 100 columns #275: FILE: drivers/clk/clk-npcm8xx.c:214:
+ { NPCM8XX_CLKDIV3, 11, 5, "uart2", &npcm8xx_muxes[3].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_UART2 },

WARNING: line length of 111 exceeds 100 columns #276: FILE: drivers/clk/clk-npcm8xx.c:215:
+ { NPCM8XX_CLKDIV3, 6, 5, "spi0", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SPI0 },

WARNING: line length of 111 exceeds 100 columns #277: FILE: drivers/clk/clk-npcm8xx.c:216:
+ { NPCM8XX_CLKDIV3, 1, 5, "spix", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SPIX },

WARNING: line length of 106 exceeds 100 columns #279: FILE: drivers/clk/clk-npcm8xx.c:218:
+ { NPCM8XX_CLKDIV4, 28, 4, "rg", &npcm8xx_muxes[11].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_RG },

WARNING: line length of 108 exceeds 100 columns #280: FILE: drivers/clk/clk-npcm8xx.c:219:
+ { NPCM8XX_CLKDIV4, 12, 4, "rcp", &npcm8xx_muxes[12].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_RCP },

WARNING: line length of 133 exceeds 100 columns #282: FILE: drivers/clk/clk-npcm8xx.c:221:
+ { NPCM8XX_THRTL_CNT, 0, 2, "th", &npcm8xx_muxes[0].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_TH },

WARNING: Prefer "GPL" over "GPL v2" - see commit bf7fbeeae6db ("module: Cure the MODULE_LICENSE "GPL" vs. "GPL v2" bogosity") #490: FILE: drivers/clk/clk-npcm8xx.c:429:
+MODULE_LICENSE("GPL v2");

total: 0 errors, 24 warnings, 0 checks, 450 lines checked

Andrew

author maintainer
#6 lore raw

Re: [linux dev-6.6 v3 3/3] clk: npcm8xx: add clock controller

Hi Andrew,

the clock maintainer has approved the driver in V3 :-)

So I think we are good to go.

Thanks,

Tomer

Quoted 137 lines · Tomer Maimon

Hi Andrew,

Thanks for your comments,

Send V4 with fixed exceed line length.

Tomer

Quoted 125 lines · Andrew Jeffery
Quoted 10 lines · Tomer Maimon

Add auxiliary driver to support Nuvoton Arbel BMC NPCM8XX contains an integrated clock controller which generates and supplies clocks to all modules within the BMC.

The NPCM8xx clock controller is created using the auxiliary device framework and set up in the npcm reset driver since the NPCM8xx clock is using the same register region.

So checkpatch still warns on this one, though I think whitespace is less of a problem.

For what it's worth, here's the output I get:

Executing: ./scripts/checkpatch.pl --strict -g HEAD
WARNING: please write a help paragraph that fully describes the config symbol #33: FILE: drivers/clk/Kconfig:328:
+config COMMON_CLK_NPCM8XX

   +       tristate "Clock driver for the NPCM8XX SoC Family"
   +       depends on ARCH_NPCM || COMPILE_TEST
   +       help
   +         This driver supports the clocks on the Nuvoton BMC NPCM8XX SoC Family,
   +         all the clocks are initialized by the bootloader, so this driver
   +         allows only reading of current settings directly from the hardware.

+

WARNING: added, moved or deleted file(s), does MAINTAINERS need updating? #57:
new file mode 100644

WARNING: line length of 112 exceeds 100 columns #252: FILE: drivers/clk/clk-npcm8xx.c:191:
+ { NPCM8XX_CLKDIV1, 26, 2, "ahb", &hw_pre_clk, CLK_DIVIDER_READ_ONLY, CLK_IS_CRITICAL, NPCM8XX_CLK_AHB },

WARNING: line length of 137 exceeds 100 columns #257: FILE: drivers/clk/clk-npcm8xx.c:196:
+ { NPCM8XX_CLKDIV1, 28, 3, "adc", &npcm8xx_pre_divs[0].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_ADC },

WARNING: line length of 107 exceeds 100 columns #259: FILE: drivers/clk/clk-npcm8xx.c:198:
+ { NPCM8XX_CLKDIV1, 11, 5, "mmc", &npcm8xx_muxes[2].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_MMC },

WARNING: line length of 106 exceeds 100 columns #261: FILE: drivers/clk/clk-npcm8xx.c:200:
+ { NPCM8XX_CLKDIV1, 2, 4, "pci", &npcm8xx_muxes[7].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_PCI },

WARNING: line length of 139 exceeds 100 columns #263: FILE: drivers/clk/clk-npcm8xx.c:202:
+ { NPCM8XX_CLKDIV2, 30, 2, "apb4", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB4 },

WARNING: line length of 139 exceeds 100 columns #264: FILE: drivers/clk/clk-npcm8xx.c:203:
+ { NPCM8XX_CLKDIV2, 28, 2, "apb3", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB3 },

WARNING: line length of 139 exceeds 100 columns #265: FILE: drivers/clk/clk-npcm8xx.c:204:
+ { NPCM8XX_CLKDIV2, 26, 2, "apb2", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB2 },

WARNING: line length of 139 exceeds 100 columns #266: FILE: drivers/clk/clk-npcm8xx.c:205:
+ { NPCM8XX_CLKDIV2, 24, 2, "apb1", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB1 },

WARNING: line length of 139 exceeds 100 columns #267: FILE: drivers/clk/clk-npcm8xx.c:206:
+ { NPCM8XX_CLKDIV2, 22, 2, "apb5", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_APB5 },

WARNING: line length of 113 exceeds 100 columns #268: FILE: drivers/clk/clk-npcm8xx.c:207:
+ { NPCM8XX_CLKDIV2, 16, 5, "clkout", &npcm8xx_muxes[8].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_CLKOUT },

WARNING: line length of 107 exceeds 100 columns #269: FILE: drivers/clk/clk-npcm8xx.c:208:
+ { NPCM8XX_CLKDIV2, 13, 3, "gfx", &npcm8xx_muxes[7].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_GFX },

WARNING: line length of 112 exceeds 100 columns #270: FILE: drivers/clk/clk-npcm8xx.c:209:
+ { NPCM8XX_CLKDIV2, 8, 5, "usb_bridge", &npcm8xx_muxes[4].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SU },

WARNING: line length of 112 exceeds 100 columns #271: FILE: drivers/clk/clk-npcm8xx.c:210:
+ { NPCM8XX_CLKDIV2, 4, 4, "usb_host", &npcm8xx_muxes[4].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SU48 },

WARNING: line length of 108 exceeds 100 columns #272: FILE: drivers/clk/clk-npcm8xx.c:211:
+ { NPCM8XX_CLKDIV2, 0, 4, "sdhc", &npcm8xx_muxes[2].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SDHC },

WARNING: line length of 112 exceeds 100 columns #274: FILE: drivers/clk/clk-npcm8xx.c:213:
+ { NPCM8XX_CLKDIV3, 16, 8, "spi1", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SPI1 },

WARNING: line length of 111 exceeds 100 columns #275: FILE: drivers/clk/clk-npcm8xx.c:214:
+ { NPCM8XX_CLKDIV3, 11, 5, "uart2", &npcm8xx_muxes[3].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_UART2 },

WARNING: line length of 111 exceeds 100 columns #276: FILE: drivers/clk/clk-npcm8xx.c:215:
+ { NPCM8XX_CLKDIV3, 6, 5, "spi0", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SPI0 },

WARNING: line length of 111 exceeds 100 columns #277: FILE: drivers/clk/clk-npcm8xx.c:216:
+ { NPCM8XX_CLKDIV3, 1, 5, "spix", &npcm8xx_pre_divs[1].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_SPIX },

WARNING: line length of 106 exceeds 100 columns #279: FILE: drivers/clk/clk-npcm8xx.c:218:
+ { NPCM8XX_CLKDIV4, 28, 4, "rg", &npcm8xx_muxes[11].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_RG },

WARNING: line length of 108 exceeds 100 columns #280: FILE: drivers/clk/clk-npcm8xx.c:219:
+ { NPCM8XX_CLKDIV4, 12, 4, "rcp", &npcm8xx_muxes[12].hw, CLK_DIVIDER_READ_ONLY, 0, NPCM8XX_CLK_RCP },

WARNING: line length of 133 exceeds 100 columns #282: FILE: drivers/clk/clk-npcm8xx.c:221:
+ { NPCM8XX_THRTL_CNT, 0, 2, "th", &npcm8xx_muxes[0].hw, CLK_DIVIDER_READ_ONLY | CLK_DIVIDER_POWER_OF_TWO, 0, NPCM8XX_CLK_TH },

WARNING: Prefer "GPL" over "GPL v2" - see commit bf7fbeeae6db ("module: Cure the MODULE_LICENSE "GPL" vs. "GPL v2" bogosity") #490: FILE: drivers/clk/clk-npcm8xx.c:429:
+MODULE_LICENSE("GPL v2");

total: 0 errors, 24 warnings, 0 checks, 450 lines checked

Andrew

maintainer
#7 lore raw

Re: [linux dev-6.6 v3 3/3] clk: npcm8xx: add clock controller

Quoted 5 lines · Tomer Maimon

Hi Andrew,

the clock maintainer has approved the driver in V3 :-)

So I think we are good to go.

Yep. I'll backport the changes straight from upstream, unless I discover any issues in the process.

Andrew