arm64: dts: rockchip: rock-3a: Remove bluetooth node
Subsystems (2)
PATCH 1/1 arm64: dts: rockchip: rock-3a: Remove bluetooth node
From: Chen-Yu Tsai <[email protected]>
The Bluetooth node described in the device tree is actually on an M.2 slot. What module is present depends on what the end user installed, and should be left to an overlay.
Remove the existing bluetooth node. This gets rid of bogus timeout errors.
--- arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts | 14 -------------- 1 file changed, 14 deletions(-)
arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts +0 -14
@@ -778,20 +778,6 @@ &uart1 { pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>; uart-has-rtscts; status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - clocks = <&rk809 1>; - clock-names = "lpo"; - device-wakeup-gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>; - host-wakeup-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>; - shutdown-gpios = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&bt_host_wake &bt_wake &bt_enable>; - vbat-supply = <&vcc3v3_sys>; - vddio-supply = <&vcc_1v8>; - /* vddio comes from regulator on module, use IO bank voltage instead */ - }; }; &uart2 {
Signature · 1 line
2.39.5
Hi,
What about adding another patch that converts it to a dtso?
Best regards,
Shengyu
Quoted 40 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
The Bluetooth node described in the device tree is actually on an M.2 slot. What module is present depends on what the end user installed, and should be left to an overlay.
Remove the existing bluetooth node. This gets rid of bogus timeout errors.
Fixes 8cf890aabd45 ("arm64: dts: rockchip: Add nodes for SDIO/UART Wi-Fi/Bluetooth modules to Radxa Rock 3A")Signed-off-by Chen-Yu Tsai <[email protected]>--- arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts | 14 -------------- 1 file changed, 14 deletions(-)arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts +0
-14@@ -778,20 +778,6 @@ &uart1 { pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>; uart-has-rtscts; status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - clocks = <&rk809 1>; - clock-names = "lpo"; - device-wakeup-gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>; - host-wakeup-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>; - shutdown-gpios = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&bt_host_wake &bt_wake &bt_enable>; - vbat-supply = <&vcc3v3_sys>; - vddio-supply = <&vcc_1v8>; - /* vddio comes from regulator on module, use IO bank voltage instead */ - }; }; &uart2 {
Quoted 8 lines · Chen-Yu Tsai
The Bluetooth node described in the device tree is actually on an M.2 slot. What module is present depends on what the end user installed, and should be left to an overlay.
Remove the existing bluetooth node. This gets rid of bogus timeout errors.
[...]
Applied, thanks!
[1/1] arm64: dts: rockchip: rock-3a: Remove bluetooth node
commit: 9602f47fe6dcca9318f35f7b72b4e98b91c5a5cf
Best regards,
Signature · 1 line
Heiko Stuebner <[email protected]>