dt-bindings: serial: Convert microchip,pic32mzda-uart to DT schema
Subsystems (2)
Rob Herring (Arm)
maintainerPATCH 1/1 dt-bindings: serial: Convert microchip,pic32mzda-uart to DT schema
Convert the Microchip PIC32 UART binding to DT schema. The binding was unclear there are 3 interrupts. The functions were determined from the driver. The 'cts-gpios' property is covered by serial.yaml schema.
--- .../bindings/serial/microchip,pic32-uart.txt | 29 ---------- .../serial/microchip,pic32mzda-uart.yaml | 53 +++++++++++++++++++ 2 files changed, 53 insertions(+), 29 deletions(-) delete mode 100644 Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/microchip,pic32mzda-uart.yaml
Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt deleted +0 -29
@@ -1,29 +0,0 @@ -* Microchip Universal Asynchronous Receiver Transmitter (UART) - -Required properties: -- compatible: Should be "microchip,pic32mzda-uart" -- reg: Should contain registers location and length -- interrupts: Should contain interrupt -- clocks: Phandle to the clock. - See: Documentation/devicetree/bindings/clock/clock-bindings.txt -- pinctrl-names: A pinctrl state names "default" must be defined. -- pinctrl-0: Phandle referencing pin configuration of the UART peripheral. - See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - -Optional properties: -- cts-gpios: CTS pin for UART - -Example: - uart1: serial@1f822000 { - compatible = "microchip,pic32mzda-uart"; - reg = <0x1f822000 0x50>; - interrupts = <112 IRQ_TYPE_LEVEL_HIGH>, - <113 IRQ_TYPE_LEVEL_HIGH>, - <114 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rootclk PB2CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1 - &pinctrl_uart1_cts - &pinctrl_uart1_rts>; - cts-gpios = <&gpio1 15 0>; - };
Documentation/devicetree/bindings/serial/microchip,pic32mzda-uart.yaml new file +53 -0
53 lines not on this page · raw message
Signature · 1 line
2.47.2
Rob Herring (Arm)
maintainerQuoted 4 lines · Rob Herring (Arm)
Convert the Microchip PIC32 UART binding to DT schema. The binding was unclear there are 3 interrupts. The functions were determined from the driver. The 'cts-gpios' property is covered by
serial.yamlschema.
Quoted 8 lines
Signed-off-by Rob Herring (Arm) <[email protected]>--- .../bindings/serial/microchip,pic32-uart.txt | 29 ---------- .../serial/microchip,pic32mzda-uart.yaml | 53 +++++++++++++++++++ 2 files changed, 53 insertions(+), 29 deletions(-) delete mode 100644 Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt create mode 100644 Documentation/devicetree/bindings/serial/microchip,pic32mzda-uart.yaml
My bot found errors running 'make dt_binding_check' on your patch:
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/serial/microchip,pic32mzda-uart.example.dtb: serial@1f822000 (microchip,pic32mzda-uart): Unevaluated properties are not allowed ('cts-gpios' was unexpected)
from schema $id: http://devicetree.org/schemas/microchip,pic32mzda-uart.yaml#
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]
The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.