Skip to contentSkip to conversation

Add FriendlyElec NanoPi M5 support for Rockchip RK3576

PATCH Applied John Clark 2 participants 4 messages Jun 28, 2025 – Jul 10, 2025

Subsystems (2)
lore
Share & tools
lore

John Clark

author
#0 lore raw

v5 cover Add FriendlyElec NanoPi M5 support for Rockchip RK3576

This series adds device tree support for the FriendlyElec NanoPi M5 board, powered by the Rockchip RK3576 SoC (4x Cortex-A72, 4x Cortex-A53, Mali-G52 MC3 GPU, 6 TOPS NPU). The patches enable basic booting and connectivity, including dual 1Gbps Ethernet, USB 3.2, microSD, M.2 PCIe NVMe, and HDMI.

Changes in v5:
- Addressed Jonas Karlman's feedback:
- Added mmc0 alias for SD card
- Updated regulator names to match schematic (e.g., vcc12v_dcin,

       vcc5v0_sys_s5, vcc3v3_m2_keym, vcc3v3_sd_s0, usb3_port2_5v,
       vcc5v0_usb_otg0, vcc5v_hdmi_tx)
   - Fixed vcc3v3_sd_s0 voltage to 3.3V
   - Removed unnecessary regulator-state-mem for fixed regulators
   - Removed vcc_5v0_device regulator
   - Added pinctrl for Ethernet PHY reset GPIOs in mdio0 and mdio1
   - Used correct pinctrl format for sdmmc and sfc1 (<&pin>)
   - Increased SPI flash frequency to 50 MHz
   - Updated LED colors (sys: red, led1/led2: green) and functions
       (LED_FUNCTION_HEARTBEAT, LED_FUNCTION_LAN)
   - Dropped rng node (enabled by default)
   - Omitted HDMI mode-switching GPIO (to be added later with driver
       support)
   - Updated pinctrl names to match schematic (e.g., pcie0_pwren_h,
       sdmmc0_pwren_h, usb3_host_pwren_h, usb_otg0_pwren_h, hp_det_l,
       pcie0_perstn)

Changes in v4:
- Addressed Diederik's feedback:
- Renamed pinctrl nodes to align with schematic labels
- Moved pinctrl-0 and pinctrl-names into button-user sub-node

Changes in v3:
- Improved (even more) fspi1m1_pins comment for clarity, specifying gpio1_d5, gpio1_c4-c7 (clk, d0-d4) for SPI NOR flash.
- Removed redundant #address-cells and #size-cells from sfc1 node, as they are inherited from rk3576.dtsi.

Changes in v2:
- Fixed DT schema warnings (Rob Herring):
- Renamed spi-nor@0 to flash@0
- Renamed pmic@23 pinctrl nodes to end with -pins
- Renamed hym8563@51 to rtc@51 and removed clock-frequency
- Renamed button@1 to button-user
- Addressed Heiko Stuebner's feedback:
- Sorted non-addressed nodes alphabetically
- Added blank lines in regulator nodes
- Improved fspi1m1_pins comment to clarify SPI NOR flash pinmux
- Moved status property in saradc to last

Patch 1: Updates DT bindings in rockchip.yaml Patch 2: Adds NanoPi M5 device tree and Makefile entry

No MAINTAINERS update needed, as the new file is covered by the existing ARM/Rockchip SoC entry.

Tested on NanoPi M5 with successful boot and feature validation.

---
John Clark (2):
dt-bindings: arm: rockchip: add FriendlyElec NanoPi M5 board
arm64: dts: rockchip: Add FriendlyElec NanoPi M5 support

 .../devicetree/bindings/arm/rockchip.yaml     |   6 +
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3576-nanopi-m5.dts    | 941 ++++++++++++++++++
 3 files changed, 948 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-nanopi-m5.dts
Signature · 1 line
2.39.5
author
#1 lore raw

PATCH v5 1/2 dt-bindings: arm: rockchip: add FriendlyElec NanoPi M5 board

Add device tree documentation for rk3576-nanopi-m5

---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 6 ++++++
 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/arm/rockchip.yaml +6 -0
index 58b9312c6c73..28db6bd6aa5b 100644
@@ -300,6 +300,12 @@ properties:
               - friendlyarm,nanopi-r4s-enterprise
           - const: rockchip,rk3399
 
+      - description: FriendlyElec NanoPi M5 series boards
+        items:
+          - enum:
+              - friendlyarm,nanopi-m5
+          - const: rockchip,rk3576
+
       - description: FriendlyElec NanoPi R5 series boards
         items:
           - enum:
Signature · 1 line
2.39.5
author
#2 lore raw

PATCH v5 2/2 arm64: dts: rockchip: Add FriendlyElec NanoPi M5 support

In reply to John Clark

Add device tree for FriendlyElec NanoPi M5 with Rockchip RK3576 SoC (4x Cortex-A72, 4x Cortex-A53, Mali-G52 MC3 GPU, 6 TOPS NPU). Enables basic booting and connectivity.

Supported features:
- RK3576 SoC
- 4GB LPDDR4X or 8GB/16GB LPDDR5
- 16MB SPI Nor Flash
- 2x 1Gbps Ethernet
- 2x USB 3.2 Gen 1 Type-A ports
- M.2 M-Key PCIe 2.1 x1 NVMe support
- M.2 E-Key SDIO connector
- microSD UHS-I
- HDMI 1.4/2.0 (up to 4096x2304@60Hz)
- 30-pin GPIO (2x SPI, 4x UART, 3x I2C, 5x PWM, 20x GPIO)
- Debug UART
- RTC with HYM8563TS
- Power via USB-C (PD, 6V~20V)

---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3576-nanopi-m5.dts    | 941 ++++++++++++++++++
 2 files changed, 942 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-nanopi-m5.dts
arch/arm64/boot/dts/rockchip/Makefile +1 -0
index e43565c53c56..099520962ffb 100644
@@ -148,6 +148,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5-v1.2-wifibt.dtbo
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb1-v10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-luckfox-omni3576.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-nanopi-m5.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-rock-4d.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3582-radxa-e52c.dtb
arch/arm64/boot/dts/rockchip/rk3576-nanopi-m5.dts new file +941 -0

941 lines not on this page · raw message

Signature · 1 line
2.39.5
maintainer Applied
#3 lore raw
In reply to John Clark
Quoted 26 lines · John Clark

This series adds device tree support for the FriendlyElec NanoPi M5 board, powered by the Rockchip RK3576 SoC (4x Cortex-A72, 4x Cortex-A53, Mali-G52 MC3 GPU, 6 TOPS NPU). The patches enable basic booting and connectivity, including dual 1Gbps Ethernet, USB 3.2, microSD, M.2 PCIe NVMe, and HDMI.

Changes in v5:
- Addressed Jonas Karlman's feedback:
- Added mmc0 alias for SD card
- Updated regulator names to match schematic (e.g., vcc12v_dcin,

       vcc5v0_sys_s5, vcc3v3_m2_keym, vcc3v3_sd_s0, usb3_port2_5v,
       vcc5v0_usb_otg0, vcc5v_hdmi_tx)
   - Fixed vcc3v3_sd_s0 voltage to 3.3V
   - Removed unnecessary regulator-state-mem for fixed regulators
   - Removed vcc_5v0_device regulator
   - Added pinctrl for Ethernet PHY reset GPIOs in mdio0 and mdio1
   - Used correct pinctrl format for sdmmc and sfc1 (<&pin>)
   - Increased SPI flash frequency to 50 MHz
   - Updated LED colors (sys: red, led1/led2: green) and functions
       (LED_FUNCTION_HEARTBEAT, LED_FUNCTION_LAN)
   - Dropped rng node (enabled by default)
   - Omitted HDMI mode-switching GPIO (to be added later with driver
       support)
   - Updated pinctrl names to match schematic (e.g., pcie0_pwren_h,
       sdmmc0_pwren_h, usb3_host_pwren_h, usb_otg0_pwren_h, hp_det_l,
       pcie0_perstn)
Quoted 1 line

[...]

Applied, thanks!

[1/2] dt-bindings: arm: rockchip: add FriendlyElec NanoPi M5 board

      commit: d15e51907ef472d31af0a4f735d4597b53dc379e
[2/2] arm64: dts: rockchip: Add FriendlyElec NanoPi M5 support
      commit: f2a71544d56bc8de459e1df9eecf616d141cd633

Best regards,

Signature · 1 line
Heiko Stuebner <[email protected]>