ARM: dts: stm32: Enable PHY SSC on DH STM32MP13xx DHCOR DHSBC board
Marek Vasut
maintainerPATCH 1/1 ARM: dts: stm32: Enable PHY SSC on DH STM32MP13xx DHCOR DHSBC board
Add realtek,rxc-ssc-enable and realtek,sysclk-ssc-enable to both PHY DT nodes to enable PHY Spread Spectrum on RXC and SYSCLK, CLKOUT is disabled and therefore does not need SSC enabled.
---
Cc: Alexandre Torgue <[email protected]>
Cc: Christoph Niedermaier <[email protected]>
Cc: Conor Dooley <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
--- arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts +4 -0
@@ -97,6 +97,8 @@ ethphy1: ethernet-phy@1 { interrupts = <12 IRQ_TYPE_LEVEL_LOW>; reg = <1>; realtek,clkout-disable; + realtek,rxc-ssc-enable; + realtek,sysclk-ssc-enable; reset-assert-us = <15000>; reset-deassert-us = <55000>; reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
@@ -146,6 +148,8 @@ ethphy2: ethernet-phy@1 { interrupts = <15 IRQ_TYPE_LEVEL_LOW>; reg = <1>; realtek,clkout-disable; + realtek,rxc-ssc-enable; + realtek,sysclk-ssc-enable; reset-assert-us = <15000>; reset-deassert-us = <55000>; reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;
Signature · 1 line
2.53.0
Alexandre TORGUE
maintainerHi Marek
Quoted 35 lines · Marek Vasut
Add realtek,rxc-ssc-enable and realtek,sysclk-ssc-enable to both PHY DT nodes to enable PHY Spread Spectrum on RXC and SYSCLK, CLKOUT is disabled and therefore does not need SSC enabled.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Alexandre Torgue <[email protected]>
Cc: Christoph Niedermaier <[email protected]>
Cc: Conor Dooley <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]--- arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts | 4 ++++ 1 file changed, 4 insertions(+)arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts +2
-0@@ -97,6 +97,8 @@ ethphy1: ethernet-phy@1 { interrupts = <12 IRQ_TYPE_LEVEL_LOW>; reg = <1>; realtek,clkout-disable; + realtek,rxc-ssc-enable; + realtek,sysclk-ssc-enable; reset-assert-us = <15000>; reset-deassert-us = <55000>; reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts ethphy2: ethernet-phy@1 { · line 155
Quoted 8 lines
arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts +2
-0@@ -146,6 +148,8 @@ ethphy2: ethernet-phy@1 { interrupts = <15 IRQ_TYPE_LEVEL_LOW>; reg = <1>; realtek,clkout-disable; + realtek,rxc-ssc-enable; + realtek,sysclk-ssc-enable; reset-assert-us = <15000>; reset-deassert-us = <55000>; reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;
Applied on stm32-next.
Thanks
Alex