iio: adc: ti-ads1015: modernize resource management
v3 cover iio: adc: ti-ads1015: modernize resource management
This series modernizes the ti-ads1015 by transitioning it to a fully devm_ architecture.
By moving resource allocation, device registration, and runtime power management to the devm_ infrastructure, the teardown sequence is now guaranteed to execute safely in the reverse order of initialization. This allows for the complete removal of the ads1015_remove() function, eliminating boilerplate code and reducing the risk of future resource leaks.
Also the driver's configuration logic has been updated to use the modern FIELD_PREP() and FIELD_GET() macros, allowing the removal of all custom _SHIFT macros and a redundant helper function.
Additionally, housekeeping patches are included to ensure header includes remain alphabetically sorted, dev_err_probe() is used consistently, and PM macros are updated to modern standards.
Changes in v3:
- Added Patch 7 to replace all custom _SHIFT macros with FIELD_PREP and FIELD_GET as requested by Jonathan Cameron.
- Added Patch 8 to inline ads1015_set_conv_mode() directly at call sites, allowing for the removal of the final _SHIFT macro.
Changes in v2:
- Split the monolithic v1 patch into a 6-patch series to isolate housekeeping, bug fixes, and API modernizations for easier review and backporting.
- Patch 1: Added to modernize PM ops and remove #ifdef CONFIG_PM.
- Patch 2: Added to fix a pre-existing PM leak on probe failure identified by Jonathan Cameron.
- Patch 3: Extracted header sorting into a prerequisite patch.
- Patch 4 & 5: Extracted the introduction of the local 'dev' pointer and dev_err_probe() conversions, suggested by Jonathan Cameron.
- Patch 6: Now contains only the devm_ conversions and the removal of ads1015_remove().
Archit Anant (8):
iio: adc: ti-ads1015: use DEFINE_RUNTIME_DEV_PM_OPS()
iio: adc: ti-ads1015: fix PM leak on probe failure
iio: adc: ti-ads1015: sort headers alphabetically
iio: adc: ti-ads1015: use local device pointer in probe
iio: adc: ti-ads1015: use dev_err_probe() for error handling
iio: adc: ti-ads1015: convert to fully managed resources
iio: adc: ti-ads1015: replace custom shift macros with FIELD_PREP/GET
iio: adc: ti-ads1015: inline ads1015_set_conv_mode()
drivers/iio/adc/ti-ads1015.c | 176 ++++++++++++++++------------------- 1 file changed, 81 insertions(+), 95 deletions(-)
Signature · 1 line
2.39.5
PATCH v3 1/8 iio: adc: ti-ads1015: use DEFINE_RUNTIME_DEV_PM_OPS()
Replace the deprecated SET_RUNTIME_PM_OPS() with the modern DEFINE_RUNTIME_DEV_PM_OPS() macro. This allows for the removal of the macro automatically handles dropping unused functions when PM is disabled.
Update the driver struct to use pm_ptr() to avoid unused variable warnings.
--- drivers/iio/adc/ti-ads1015.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-)
drivers/iio/adc/ti-ads1015.c +5 -7
@@ -1066,7 +1066,6 @@ static void ads1015_remove(struct i2c_client *client) ERR_PTR(ret)); } -#ifdef CONFIG_PM static int ads1015_runtime_suspend (struct device *dev) {struct iio_dev *indio_dev =i2c_get_clientdata (to_i2c_client (dev));
@@ -1087,12 +1086,11 @@ static int ads1015_runtime_resume(struct device *dev)return ret; } -#endif -static const struct dev_pm_ops ads1015_pm_ops = { -SET_RUNTIME_PM_OPS (ads1015_runtime_suspend, - ads1015_runtime_resume,NULL ) -}; +static DEFINE_RUNTIME_DEV_PM_OPS(ads1015_pm_ops, + ads1015_runtime_suspend, + ads1015_runtime_resume, + NULL);static const struct ads1015_chip_data ads1015_data = { .channels = ads1015_channels,
@@ -1147,7 +1145,7 @@ static struct i2c_driver ads1015_driver = { .driver = { .name = ADS1015_DRV_NAME, .of_match_table = ads1015_of_match, - .pm = &ads1015_pm_ops, + .pm = pm_ptr(&ads1015_pm_ops), }, .probe = ads1015_probe, .remove = ads1015_remove,
Signature · 1 line
2.39.5
PATCH v3 2/8 iio: adc: ti-ads1015: fix PM leak on probe failure
In reply to Archit AnantIf iio_device_register() fails during probe(), the runtime PM subsystem is left enabled. This leads to a resource leak upon failure.
Add the missing pm_runtime_disable() and pm_runtime_set_suspended() calls to the probe() error path to ensure proper cleanup.
--- drivers/iio/adc/ti-ads1015.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/iio/adc/ti-ads1015.c +2 -0
@@ -1042,6 +1042,8 @@ static int ads1015_probe(struct i2c_client *client) ret =iio_device_register (indio_dev);if (ret <0 ) {dev_err (&client->dev,"Failed to register IIO device\n" ); +pm_runtime_disable (&client->dev); +pm_runtime_set_suspended (&client->dev);return ret; }
Signature · 1 line
2.39.5
Re: [PATCH v3 2/8] iio: adc: ti-ads1015: fix PM leak on probe failure
Quoted 7 lines · Archit Anant
If
iio_device_register()fails duringprobe(), the runtime PM subsystem is left enabled. This leads to a resource leak upon failure.Add the missing
pm_runtime_disable()andpm_runtime_set_suspended()calls to theprobe()error path to ensure proper cleanup.Reported-by Jonathan Cameron <[email protected]>
Was it public email?
Ah, this should be Closes: tag instead of Link.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Jonathan Cameron
maintainerRe: [PATCH v3 2/8] iio: adc: ti-ads1015: fix PM leak on probe failure
Quoted 7 lines · On Thu, 13 Aug 2026 11:51:28 +0300 Andy Shevchenko…
Quoted 5 lines · Archit Anant
If
iio_device_register()fails duringprobe(), the runtime PM subsystem is left enabled. This leads to a resource leak upon failure.Add the missing
pm_runtime_disable()andpm_runtime_set_suspended()calls to theprobe()error path to ensure proper cleanup.
Quoted 8 lines
Quoted 1 line
Reported-by Jonathan Cameron <[email protected]>Was it public email?
Ah, this should be Closes: tag instead of Link.
I never checked but this is already fixed in the iio tree and the relevant devm rework done. :( So much going on at the moment in IIO I didn't recall this one at all!
https://lore.kernel.org/all/[email protected]/
Please rebase the remainder of the series.
Jonathan
Re: [PATCH v3 2/8] iio: adc: ti-ads1015: fix PM leak on probe failure
Quoted 20 lines · Jonathan Cameron
Quoted 7 lines · On Thu, 13 Aug 2026 11:51:28 +0300 Andy Shevchenko…
Quoted 5 lines · Archit Anant
If
iio_device_register()fails duringprobe(), the runtime PM subsystem is left enabled. This leads to a resource leak upon failure.Add the missing
pm_runtime_disable()andpm_runtime_set_suspended()calls to theprobe()error path to ensure proper cleanup.Quoted 8 lines
Quoted 1 line
Reported-by Jonathan Cameron <[email protected]>Was it public email?
Ah, this should be Closes: tag instead of Link.
Quoted 7 lines
I never checked but this is already fixed in the iio tree and the relevant devm rework done. :( So much going on at the moment in IIO I didn't recall this one at all!
https://lore.kernel.org/all/[email protected]/
Please rebase the remainder of the series.
Oh, I missed that as well, nvm. I'll rebase the rest!
Signature · 2 lines
Sincerely, Archit Anant
PATCH v3 3/8 iio: adc: ti-ads1015: sort headers alphabetically
In reply to Archit AnantReorder include headers alphabetically to comply with the preferred coding style and improve maintainability.
No functional changes.
--- drivers/iio/adc/ti-ads1015.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)
drivers/iio/adc/ti-ads1015.c +9 -9
@@ -11,24 +11,24 @@* * 0x4B - ADDR connected to SCL */ -#include <linux/module.h> #include <linux/cleanup.h> +#include <linux/delay.h> +#include <linux/i2c.h> #include <linux/init.h> #include <linux/irq.h> -#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/pm_runtime.h> #include <linux/property.h> #include <linux/regmap.h> -#include <linux/pm_runtime.h> -#include <linux/mutex.h> -#include <linux/delay.h> +#include <linux/iio/buffer.h> +#include <linux/iio/events.h> #include <linux/iio/iio.h> -#include <linux/iio/types.h> #include <linux/iio/sysfs.h> -#include <linux/iio/events.h> -#include <linux/iio/buffer.h> -#include <linux/iio/triggered_buffer.h> #include <linux/iio/trigger_consumer.h> +#include <linux/iio/triggered_buffer.h> +#include <linux/iio/types.h> #define ADS1015_DRV_NAME "ads1015"
Signature · 1 line
2.39.5
PATCH v3 4/8 iio: adc: ti-ads1015: use local device pointer in probe
In reply to Archit AnantIntroduce a local device pointer 'dev' in ads1015_probe to avoid accessing &client->dev repeatedly.
--- drivers/iio/adc/ti-ads1015.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-)
drivers/iio/adc/ti-ads1015.c +11 -10
@@ -933,6 +933,7 @@ static int ads1015_set_conv_mode(struct ads1015_data *data, int mode)static int ads1015_probe (struct i2c_client *client) {const struct ads1015_chip_data *chip; +struct device *dev = &client->dev;struct iio_dev *indio_dev;struct ads1015_data *data;int ret;
@@ -940,9 +941,9 @@ static int ads1015_probe(struct i2c_client *client) chip =i2c_get_match_data (client);if (!chip) -return dev_err_probe (&client->dev, -EINVAL ,"Unknown chip\n" ); +return dev_err_probe (dev, -EINVAL ,"Unknown chip\n" ); - indio_dev =devm_iio_device_alloc (&client->dev,sizeof (*data)); + indio_dev =devm_iio_device_alloc (dev,sizeof (*data));if (!indio_dev)return -ENOMEM ;
@@ -982,7 +983,7 @@ static int ads1015_probe(struct i2c_client *client)return PTR_ERR (data->regmap); } - ret =devm_iio_triggered_buffer_setup (&client->dev, indio_dev,NULL , + ret =devm_iio_triggered_buffer_setup (dev, indio_dev,NULL , ads1015_trigger_handler, &ads1015_buffer_setup_ops);if (ret <0 ) {
@@ -1018,7 +1019,7 @@ static int ads1015_probe(struct i2c_client *client)if (ret)return ret; - ret =devm_request_threaded_irq (&client->dev, client->irq, + ret =devm_request_threaded_irq (dev, client->irq,NULL , ads1015_event_handler, irq_trig |IRQF_ONESHOT , client->name, indio_dev);
@@ -1032,18 +1033,18 @@ static int ads1015_probe(struct i2c_client *client) data->conv_invalid = true; - ret =pm_runtime_set_active (&client->dev); + ret =pm_runtime_set_active (dev);if (ret)return ret; -pm_runtime_set_autosuspend_delay (&client->dev,ADS1015_SLEEP_DELAY_MS ); -pm_runtime_use_autosuspend (&client->dev); -pm_runtime_enable (&client->dev); +pm_runtime_set_autosuspend_delay (dev,ADS1015_SLEEP_DELAY_MS ); +pm_runtime_use_autosuspend (dev); +pm_runtime_enable (dev); ret =iio_device_register (indio_dev);if (ret <0 ) {dev_err (&client->dev,"Failed to register IIO device\n" ); -pm_runtime_disable (&client->dev); -pm_runtime_set_suspended (&client->dev); +pm_runtime_disable (dev); +pm_runtime_set_suspended (dev);return ret; }
Signature · 1 line
2.39.5
PATCH v3 5/8 iio: adc: ti-ads1015: use dev_err_probe() for error handling
In reply to Archit AnantSimplify the error handling paths in ads1015_probe() and ads1015_client_get_channels_config() by converting dev_err() calls that are immediately followed by a return statement over to the modern dev_err_probe() helper.
Note: This patch takes advantage of the previously introduced local 'dev' pointer when converting the legacy dev_err(&client->dev, ...) calls, avoiding unnecessary code churn.
--- drivers/iio/adc/ti-ads1015.c | 32 ++++++++++++++------------------ 1 file changed, 14 insertions(+), 18 deletions(-)
drivers/iio/adc/ti-ads1015.c +14 -18
@@ -883,18 +883,16 @@ static int ads1015_client_get_channels_config(struct i2c_client *client)if (!fwnode_property_read_u32 (node,"ti,gain" , &pval)) { pga = pval; -if (pga >5 ) { -dev_err (dev,"invalid gain on %pfw\n" , node); -return -EINVAL ; - } +if (pga >5 ) +return dev_err_probe (dev, -EINVAL , +"invalid gain on %pfw\n" , node); }if (!fwnode_property_read_u32 (node,"ti,datarate" , &pval)) { data_rate = pval; -if (data_rate >7 ) { -dev_err (dev,"invalid data_rate on %pfw\n" , node); -return -EINVAL ; - } +if (data_rate >7 ) +return dev_err_probe (dev, -EINVAL , +"invalid data_rate on %pfw\n" , node); } data->channel_data[channel].pga = pga;
@@ -978,18 +976,16 @@ static int ads1015_probe(struct i2c_client *client) data->regmap =devm_regmap_init_i2c (client, chip->has_comparator ? &ads1015_regmap_config : &tla2024_regmap_config); -if (IS_ERR (data->regmap)) { -dev_err (&client->dev,"Failed to allocate register map\n" ); -return PTR_ERR (data->regmap); - } +if (IS_ERR (data->regmap)) +return dev_err_probe (dev,PTR_ERR (data->regmap), +"Failed to allocate register map\n" ); ret =devm_iio_triggered_buffer_setup (dev, indio_dev,NULL , ads1015_trigger_handler, &ads1015_buffer_setup_ops); -if (ret <0 ) { -dev_err (&client->dev,"iio triggered buffer setup failed\n" ); -return ret; - } +if (ret <0 ) +return dev_err_probe (dev, ret, +"iio triggered buffer setup failed\n" );if (client->irq && chip->has_comparator) {unsigned long irq_trig =irq_get_trigger_type (client->irq);
@@ -1042,10 +1038,10 @@ static int ads1015_probe(struct i2c_client *client) ret =iio_device_register (indio_dev);if (ret <0 ) { -dev_err (&client->dev,"Failed to register IIO device\n" );pm_runtime_disable (dev);pm_runtime_set_suspended (dev); -return ret; +return dev_err_probe (dev, ret, +"Failed to register IIO device\n" ); }return 0 ;
Signature · 1 line
2.39.5
Re: [PATCH v3 5/8] iio: adc: ti-ads1015: use dev_err_probe() for error handling
Quoted 9 lines · Archit Anant
Simplify the error handling paths in
ads1015_probe()andads1015_client_get_channels_config()by convertingdev_err()calls that are immediately followed by a return statement over to the moderndev_err_probe()helper.Note: This patch takes advantage of the previously introduced local 'dev' pointer when converting the legacy
dev_err(&client->dev, ...)calls, avoiding unnecessary code churn.
...
drivers/iio/adc/ti-ads1015.c static int ads1015_probe(struct i2c_client *client) · line 1048
Quoted 6 lines
drivers/iio/adc/ti-ads1015.c +0
-2ret =iio_device_register (indio_dev);if (ret <0 ) { -dev_err (&client->dev,"Failed to register IIO device\n" );pm_runtime_disable (dev);pm_runtime_set_suspended (dev); -return ret;
This shows that runtime PM calls were put to the wrong place in the previous patch. Just move them to be up, then this will be naturally accepted change.
Quoted 3 lines
drivers/iio/adc/ti-ads1015.c +2
-0+return dev_err_probe (dev, ret, +"Failed to register IIO device\n" ); }
Signature · 2 lines
With Best Regards, Andy Shevchenko
PATCH v3 6/8 iio: adc: ti-ads1015: convert to fully managed resources
In reply to Archit AnantRefactor the driver to use devm_ allocations and power management, allowing for the complete removal of the ads1015_remove()
Key changes:
- Use devm_add_action_or_reset() to ensure the ADC is safely powered down upon driver removal.
- Move to devm_pm_runtime_set_active_enabled() to manage the runtime PM lifecycle.
- Convert iio_device_register() and mutex_init() to their devm_ variants.
- Remove the thus obsolete ads1015_remove() function.
--- drivers/iio/adc/ti-ads1015.c | 43 ++++++++++++++---------------------- 1 file changed, 16 insertions(+), 27 deletions(-)
drivers/iio/adc/ti-ads1015.c +16 -27
@@ -928,6 +928,11 @@ static int ads1015_set_conv_mode(struct ads1015_data *data, int mode) mode << ADS1015_CFG_MOD_SHIFT); } +static void ads1015_power_off (void *st) +{ +ads1015_set_conv_mode (st,ADS1015_SINGLESHOT ); +} +static int ads1015_probe (struct i2c_client *client) {const struct ads1015_chip_data *chip;
@@ -948,7 +953,9 @@ static int ads1015_probe(struct i2c_client *client) data =iio_priv (indio_dev);i2c_set_clientdata (client, indio_dev); -mutex_init (&data->lock); + ret =devm_mutex_init (dev, &data->lock); +if (ret) +return ret; indio_dev->name =ADS1015_DRV_NAME ; indio_dev->modes =INDIO_DIRECT_MODE ;
@@ -1029,42 +1036,25 @@ static int ads1015_probe(struct i2c_client *client) data->conv_invalid = true; - ret =pm_runtime_set_active (dev); + ret =devm_add_action_or_reset (dev, ads1015_power_off, data);if (ret)return ret; +pm_runtime_set_autosuspend_delay (dev,ADS1015_SLEEP_DELAY_MS );pm_runtime_use_autosuspend (dev); -pm_runtime_enable (dev); - ret =iio_device_register (indio_dev); -if (ret <0 ) { -pm_runtime_disable (dev); -pm_runtime_set_suspended (dev); + ret =devm_pm_runtime_set_active_enabled (dev); +if (ret) +return ret; + + ret =devm_iio_device_register (dev, indio_dev); +if (ret)return dev_err_probe (dev, ret,"Failed to register IIO device\n" ); - }return 0 ; } -static void ads1015_remove (struct i2c_client *client) -{ -struct iio_dev *indio_dev =i2c_get_clientdata (client); -struct ads1015_data *data =iio_priv (indio_dev); -int ret; - -iio_device_unregister (indio_dev); - -pm_runtime_disable (&client->dev); -pm_runtime_set_suspended (&client->dev); - -/* power down single shot mode */ - ret =ads1015_set_conv_mode (data,ADS1015_SINGLESHOT ); -if (ret) -dev_warn (&client->dev,"Failed to power down (%pe)\n" , -ERR_PTR (ret)); -} -static int ads1015_runtime_suspend (struct device *dev) {struct iio_dev *indio_dev =i2c_get_clientdata (to_i2c_client (dev));
@@ -1147,7 +1137,6 @@ static struct i2c_driver ads1015_driver = { .pm = pm_ptr(&ads1015_pm_ops), }, .probe = ads1015_probe, - .remove = ads1015_remove, .id_table = ads1015_id, };
Signature · 1 line
2.39.5
Re: [PATCH v3 6/8] iio: adc: ti-ads1015: convert to fully managed resources
Quoted 3 lines · Archit Anant
Refactor the driver to use
devm_allocations and power management, allowing for the complete removal of theads1015_remove()
...
drivers/iio/adc/ti-ads1015.c static int ads1015_probe(struct i2c_client *client)
Quoted 5 lines
drivers/iio/adc/ti-ads1015.c +2
-2- ret =iio_device_register (indio_dev); -if (ret <0 ) { + ret =devm_pm_runtime_set_active_enabled (dev); +if (ret)
There are more places with unneeded ' < 0' comparisons, can you add an intermediate patch to drop those? With that being done, this, in particular, will have less churn.
Signature · 2 lines
With Best Regards, Andy Shevchenko
PATCH v3 7/8 iio: adc: ti-ads1015: replace custom shift macros with FIELD_PREP/GET
In reply to Archit AnantThe driver currently uses custom _SHIFT macros and manual bitwise operations to read and write to the configuration register.
Modernize the bitwise logic by replacing all manual shifts with the standard FIELD_PREP() and FIELD_GET() macros from <linux/bitfield.h>. This improves readability and prevents potential bitwise errors.
Remove the now-unused _SHIFT macros from the top of the file.
--- drivers/iio/adc/ti-ads1015.c | 39 ++++++++++++++++-------------------- 1 file changed, 17 insertions(+), 22 deletions(-)
drivers/iio/adc/ti-ads1015.c +17 -22
@@ -11,6 +11,7 @@* * 0x4B - ADDR connected to SCL */ +#include <linux/bitfield.h> #include <linux/cleanup.h> #include <linux/delay.h> #include <linux/i2c.h>
@@ -39,14 +40,7 @@#define ADS1015_LO_THRESH_REG 0x02#define ADS1015_HI_THRESH_REG 0x03 -#define ADS1015_CFG_COMP_QUE_SHIFT 0 -#define ADS1015_CFG_COMP_LAT_SHIFT 2 -#define ADS1015_CFG_COMP_POL_SHIFT 3 -#define ADS1015_CFG_COMP_MODE_SHIFT 4 -#define ADS1015_CFG_DR_SHIFT 5#define ADS1015_CFG_MOD_SHIFT 8 -#define ADS1015_CFG_PGA_SHIFT 9 -#define ADS1015_CFG_MUX_SHIFT 12#define ADS1015_CFG_COMP_QUE_MASK GENMASK(1, 0)#define ADS1015_CFG_COMP_LAT_MASK BIT(2)
@@ -408,15 +402,15 @@ int ads1015_get_adc_result(struct ads1015_data *data, int chan, int *val) dr = data->channel_data[chan].data_rate; mask =ADS1015_CFG_MUX_MASK |ADS1015_CFG_PGA_MASK |ADS1015_CFG_DR_MASK ; - cfg = chan <<ADS1015_CFG_MUX_SHIFT | pga <<ADS1015_CFG_PGA_SHIFT | - dr <<ADS1015_CFG_DR_SHIFT ; + cfg =FIELD_PREP (ADS1015_CFG_MUX_MASK , chan) |FIELD_PREP (ADS1015_CFG_PGA_MASK , pga) | +FIELD_PREP (ADS1015_CFG_DR_MASK , dr);if (ads1015_event_channel_enabled (data)) { mask |=ADS1015_CFG_COMP_QUE_MASK |ADS1015_CFG_COMP_MODE_MASK ; - cfg |= data->thresh_data[chan].comp_queue << -ADS1015_CFG_COMP_QUE_SHIFT | - data->comp_mode << -ADS1015_CFG_COMP_MODE_SHIFT ; + cfg |=FIELD_PREP (ADS1015_CFG_COMP_QUE_MASK , + data->thresh_data[chan].comp_queue) | +FIELD_PREP (ADS1015_CFG_COMP_MODE_MASK , + data->comp_mode); } cfg = (old & ~mask) | (cfg & mask);
@@ -427,7 +421,7 @@ int ads1015_get_adc_result(struct ads1015_data *data, int chan, int *val) data->conv_invalid = true; }if (data->conv_invalid) { - dr_old = (old &ADS1015_CFG_DR_MASK ) >>ADS1015_CFG_DR_SHIFT ; + dr_old =FIELD_GET (ADS1015_CFG_DR_MASK , old); conv_time =DIV_ROUND_UP (USEC_PER_SEC , data_rate[dr_old]); conv_time +=DIV_ROUND_UP (USEC_PER_SEC , data_rate[dr]); conv_time += conv_time /10 ;/* 10% internal clock inaccuracy */
@@ -758,8 +752,8 @@ static int ads1015_disable_event_config(struct ads1015_data *data, ret =regmap_update_bits (data->regmap,ADS1015_CFG_REG ,ADS1015_CFG_COMP_QUE_MASK , -ADS1015_CFG_COMP_DISABLE << -ADS1015_CFG_COMP_QUE_SHIFT ); +FIELD_PREP (ADS1015_CFG_COMP_QUE_MASK , +ADS1015_CFG_COMP_DISABLE ));if (ret)return ret;
@@ -999,19 +993,20 @@ static int ads1015_probe(struct i2c_client *client)unsigned int cfg_comp_mask =ADS1015_CFG_COMP_QUE_MASK |ADS1015_CFG_COMP_LAT_MASK |ADS1015_CFG_COMP_POL_MASK ;unsigned int cfg_comp = -ADS1015_CFG_COMP_DISABLE <<ADS1015_CFG_COMP_QUE_SHIFT | -1 <<ADS1015_CFG_COMP_LAT_SHIFT ; +FIELD_PREP (ADS1015_CFG_COMP_QUE_MASK , +ADS1015_CFG_COMP_DISABLE ) | +FIELD_PREP (ADS1015_CFG_COMP_LAT_MASK ,1 );switch (irq_trig) {case IRQF_TRIGGER_FALLING :case IRQF_TRIGGER_LOW : - cfg_comp |=ADS1015_CFG_COMP_POL_LOW << -ADS1015_CFG_COMP_POL_SHIFT ; + cfg_comp |=FIELD_PREP (ADS1015_CFG_COMP_POL_MASK , +ADS1015_CFG_COMP_POL_LOW );break ;case IRQF_TRIGGER_HIGH :case IRQF_TRIGGER_RISING : - cfg_comp |=ADS1015_CFG_COMP_POL_HIGH << -ADS1015_CFG_COMP_POL_SHIFT ; + cfg_comp |=FIELD_PREP (ADS1015_CFG_COMP_POL_MASK , +ADS1015_CFG_COMP_POL_HIGH );break ;default :return -EINVAL ;
Signature · 1 line
2.39.5
Re: [PATCH v3 7/8] iio: adc: ti-ads1015: replace custom shift macros with FIELD_PREP/GET
Quoted 8 lines · Archit Anant
The driver currently uses custom
_SHIFTmacros and manual bitwise operations to read and write to the configuration register.Modernize the bitwise logic by replacing all manual shifts with the standard
FIELD_PREP()andFIELD_GET()macros from <linux/bitfield.h>. This improves readability and prevents potential bitwise errors.Remove the now-unused
_SHIFTmacros from the top of the file.
...
drivers/iio/adc/ti-ads1015.c int ads1015_get_adc_result(struct ads1015_data *data, int chan, int *val) · line 406
Quoted 7 lines
drivers/iio/adc/ti-ads1015.c +2
-2dr = data->channel_data[chan].data_rate; mask =ADS1015_CFG_MUX_MASK |ADS1015_CFG_PGA_MASK |ADS1015_CFG_DR_MASK ; - cfg = chan <<ADS1015_CFG_MUX_SHIFT | pga <<ADS1015_CFG_PGA_SHIFT | - dr <<ADS1015_CFG_DR_SHIFT ; + cfg =FIELD_PREP (ADS1015_CFG_MUX_MASK , chan) |FIELD_PREP (ADS1015_CFG_PGA_MASK , pga) | +FIELD_PREP (ADS1015_CFG_DR_MASK , dr);
Wrong indentation. Please, make sure in the lines you touched the indentation is also correct.
...
drivers/iio/adc/ti-ads1015.c static int ads1015_probe(struct i2c_client *client) · line 998
Quoted 6 lines
drivers/iio/adc/ti-ads1015.c +3
-2unsigned int cfg_comp = -ADS1015_CFG_COMP_DISABLE <<ADS1015_CFG_COMP_QUE_SHIFT | -1 <<ADS1015_CFG_COMP_LAT_SHIFT ; +FIELD_PREP (ADS1015_CFG_COMP_QUE_MASK , +ADS1015_CFG_COMP_DISABLE ) | +FIELD_PREP (ADS1015_CFG_COMP_LAT_MASK ,1 );
It might be better to keep a longer line.
unsigned int cfg_comp = FIELD_PREP(ADS1015_CFG_COMP_QUE_MASK, ADS1015_CFG_COMP_DISABLE) | FIELD_PREP(ADS1015_CFG_COMP_LAT_MASK, 1);
Signature · 2 lines
With Best Regards, Andy Shevchenko
PATCH v3 8/8 iio: adc: ti-ads1015: inline ads1015_set_conv_mode()
In reply to Archit AnantThe ads1015_set_conv_mode() helper function is a single-line wrapper around regmap_update_bits().
With the transition to the FIELD_PREP() macro, the raw register updates are now self-documenting and easy to read. Remove the wrapper function and inline the regmap calls directly at the call sites.
This also allows for the removal of the final custom shift macro, ADS1015_CFG_MOD_SHIFT.
--- drivers/iio/adc/ti-ads1015.c | 31 ++++++++++++++++++------------- 1 file changed, 18 insertions(+), 13 deletions(-)
drivers/iio/adc/ti-ads1015.c +18 -13
@@ -40,8 +40,6 @@#define ADS1015_LO_THRESH_REG 0x02#define ADS1015_HI_THRESH_REG 0x03 -#define ADS1015_CFG_MOD_SHIFT 8 -#define ADS1015_CFG_COMP_QUE_MASK GENMASK(1, 0)#define ADS1015_CFG_COMP_LAT_MASK BIT(2)#define ADS1015_CFG_COMP_POL_MASK BIT(3)
@@ -915,16 +913,14 @@ static void ads1015_get_channels_config(struct i2c_client *client) } } -static int ads1015_set_conv_mode (struct ads1015_data *data,int mode) +static void ads1015_power_off (void *data) { -return regmap_update_bits (data->regmap,ADS1015_CFG_REG , -ADS1015_CFG_MOD_MASK , - mode <<ADS1015_CFG_MOD_SHIFT ); -} +struct ads1015_data *st = data; -static void ads1015_power_off (void *st) -{ -ads1015_set_conv_mode (st,ADS1015_SINGLESHOT ); +regmap_update_bits (st->regmap,ADS1015_CFG_REG , +ADS1015_CFG_MOD_MASK , +FIELD_PREP (ADS1015_CFG_MOD_MASK , +ADS1015_SINGLESHOT )); }static int ads1015_probe (struct i2c_client *client)
@@ -1025,7 +1021,10 @@ static int ads1015_probe(struct i2c_client *client)return ret; } - ret =ads1015_set_conv_mode (data,ADS1015_CONTINUOUS ); + ret =regmap_update_bits (data->regmap,ADS1015_CFG_REG , +ADS1015_CFG_MOD_MASK , +FIELD_PREP (ADS1015_CFG_MOD_MASK , +ADS1015_CONTINUOUS ));if (ret)return ret;
@@ -1055,7 +1054,10 @@ static int ads1015_runtime_suspend(struct device *dev)struct iio_dev *indio_dev =i2c_get_clientdata (to_i2c_client (dev));struct ads1015_data *data =iio_priv (indio_dev); -return ads1015_set_conv_mode (data,ADS1015_SINGLESHOT ); +return regmap_update_bits (data->regmap,ADS1015_CFG_REG , +ADS1015_CFG_MOD_MASK , +FIELD_PREP (ADS1015_CFG_MOD_MASK , +ADS1015_SINGLESHOT )); }static int ads1015_runtime_resume (struct device *dev)
@@ -1064,7 +1066,10 @@ static int ads1015_runtime_resume(struct device *dev)struct ads1015_data *data =iio_priv (indio_dev);int ret; - ret =ads1015_set_conv_mode (data,ADS1015_CONTINUOUS ); + ret =regmap_update_bits (data->regmap,ADS1015_CFG_REG , +ADS1015_CFG_MOD_MASK , +FIELD_PREP (ADS1015_CFG_MOD_MASK , +ADS1015_CONTINUOUS ));if (!ret) data->conv_invalid = true;
Signature · 1 line
2.39.5
Re: [PATCH v3 8/8] iio: adc: ti-ads1015: inline ads1015_set_conv_mode()
Quoted 9 lines · Archit Anant
The
ads1015_set_conv_mode()helper function is a single-line wrapper aroundregmap_update_bits().With the transition to the
FIELD_PREP()macro, the raw register updates are now self-documenting and easy to read. Remove the wrapper function and inline the regmap calls directly at the call sites.This also allows for the removal of the final custom shift macro,
ADS1015_CFG_MOD_SHIFT.
...
Quoted 7 lines
drivers/iio/adc/ti-ads1015.c +1
-5-static int ads1015_set_conv_mode (struct ads1015_data *data,int mode) +static void ads1015_power_off (void *data) { -return regmap_update_bits (data->regmap,ADS1015_CFG_REG , -ADS1015_CFG_MOD_MASK , - mode <<ADS1015_CFG_MOD_SHIFT ); -}
drivers/iio/adc/ti-ads1015.c static void ads1015_get_channels_config(struct i2c_client *client) · line 924
Quoted 10 lines
drivers/iio/adc/ti-ads1015.c +5
-3+struct ads1015_data *st = data; -static void ads1015_power_off (void *st) -{ -ads1015_set_conv_mode (st,ADS1015_SINGLESHOT ); +regmap_update_bits (st->regmap,ADS1015_CFG_REG , +ADS1015_CFG_MOD_MASK , +FIELD_PREP (ADS1015_CFG_MOD_MASK , +ADS1015_SINGLESHOT )); }
Wouldn't be better to have it as
static void ads1015_power_off(void *data)
{
unsigned int val = FIELD_PREP(ADS1015_CFG_MOD_MASK, ADS1015_SINGLESHOT);
struct regmap *map = data->regmap;
regmap_update_bits(map, ADS1015_CFG_REG, ADS1015_CFG_MOD_MASK, val);
}In lieu of this, think if the similar approach can be applied elsewhere in this driver.
Signature · 2 lines
With Best Regards, Andy Shevchenko