s390: Warn if kernel command line contains non-printable EBCDIC characters
PATCH 1/1 s390: Warn if kernel command line contains non-printable EBCDIC characters
Users may accidentally add multi-byte UTF-8 characters to zipl.conf parmline, for example, by copying snippets containing non-breaking spaces (\xC2\xA0) from web pages.
The kernel will then interpret the entire command line as EBCDIC, making it unusable. Distinguish this situation from the legitimate EBCDIC conversion by looking for non-printable characters and issue a warning.
--- arch/s390/boot/ipl_parm.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-)
arch/s390/boot/ipl_parm.c +18 -1
@@ -173,12 +173,29 @@ static inline int has_ebcdic_char(const char *str)return 0 ; } +static inline int has_nonprintable_char (const char *str) +{ +int i; + +for (i =0 ; str[i]; i++) { +unsigned char c = (unsigned char )str[i]; + +/* isprint() is Latin-1, and we need ASCII here */ +if (c <0x20 || c >0x7e ) +return 1 ; + } +return 0 ; +} +void setup_boot_command_line (void ) { parmarea.command_line[COMMAND_LINE_SIZE -1 ] =0 ;/* convert arch command line to ascii if necessary */ -if (has_ebcdic_char (parmarea.command_line)) +if (has_ebcdic_char (parmarea.command_line)) {EBCASC (parmarea.command_line,COMMAND_LINE_SIZE ); +if (has_nonprintable_char (parmarea.command_line)) +boot_warn ("Kernel command line was treated as EBCDIC, but contains non-printable characters\n" ); + }/* copy arch command line */ strscpy (early_command_line,strim (parmarea.command_line));
Signature · 1 line
2.55.0
[email protected]
AI reviewThank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
Pre-existing issues:
- [High] Integer underflow in size calculation leads to out-of-bounds write when appending IPL block parameters to a maximum-length kernel command line. --
--- Patch [1]: [PATCH] s390: Warn if kernel command line contains non-printable EBCDIC characters --- commit 0d3635825635bf3ebe41f7b2b8024aab279b4f38
Author: Ilya Leoshkevich <[email protected]>
s390: Warn if kernel command line contains non-printable EBCDIC characters
This commit adds a warning if the kernel command line contains non-printable characters after being converted from EBCDIC to ASCII. This helps detect accidentally pasted multi-byte UTF-8 sequences in zipl.conf that would otherwise render the entire command line unusable.
Quoted 4 lines
arch/s390/boot/ipl_parm.c +0
-0
[ ... ]
Quoted 4 lines
arch/s390/boot/ipl_parm.c +0
-0@@ -173,12 +173,29 @@ static inline int has_ebcdic_char(const char *str)void setup_boot_command_line (void ) { parmarea.command_line[COMMAND_LINE_SIZE -1 ] =0 ;
arch/s390/boot/ipl_parm.c static inline int has_ebcdic_char(const char *str) · line 184
Quoted 10 lines
arch/s390/boot/ipl_parm.c +4
-1/* convert arch command line to ascii if necessary */ -if (has_ebcdic_char (parmarea.command_line)) +if (has_ebcdic_char (parmarea.command_line)) {EBCASC (parmarea.command_line,COMMAND_LINE_SIZE ); +if (has_nonprintable_char (parmarea.command_line)) +boot_warn ("Kernel command line was treated as EBCDIC, but contains non-printable characters\n" ); + }/* copy arch command line */ strscpy (early_command_line,strim (parmarea.command_line));
[Severity: High]
This is a pre-existing issue, but since we are dealing with the bounds of the command line buffer here, could a maximally long command line trigger a buffer overflow shortly after this point?
Right after the quoted code, setup_boot_command_line() calls append_ipl_block_parm(), which calculates the remaining space in the buffer:
arch/s390/boot/ipl_parm.c:append_ipl_block_parm() {
...
len = strlen(early_command_line);
delim = early_command_line + len; /* '\0' character position */
parm = early_command_line + len + 1; /* append right after '\0' */
...
rc = ipl_block_get_ascii_vmparm(
parm, COMMAND_LINE_SIZE - len - 1, &ipl_block);
...
}If early_command_line is filled to its maximum capacity (COMMAND_LINE_SIZE - 1), the remaining size passed to ipl_block_get_ascii_vmparm() evaluates to 0.
Inside ipl_block_get_ascii_vmparm(), the size calculation underflows:
arch/s390/kernel/ipl_vmparm.c:ipl_block_get_ascii_vmparm() {
...
len = min_t(size_t, size - 1, ipb->ccw.vm_parm_len);
memcpy(dest, ipb->ccw.vm_parm, len);
}Because size is 0 and size_t is unsigned, size - 1 underflows to SIZE_MAX. This bypasses the bounds check and allows the memcpy() to write out of bounds.
The same underflow pattern appears in ipl_block_get_ascii_scpdata():
arch/s390/boot/ipl_parm.c:ipl_block_get_ascii_scpdata() {
...
count = min(size - 1, scpdata_length(scp_data, scp_data_len));
...
memcpy(dest, scp_data, count);
}Should there be a check ensuring size > 0 before calling these functions, or a safeguard within the get_ascii functions to prevent the underflow?
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=1
Heiko Carstens
maintainerQuoted 22 lines · Ilya Leoshkevich
Users may accidentally add multi-byte UTF-8 characters to zipl.conf parmline, for example, by copying snippets containing non-breaking spaces (\xC2\xA0) from web pages.
The kernel will then interpret the entire command line as EBCDIC, making it unusable. Distinguish this situation from the legitimate EBCDIC conversion by looking for non-printable characters and issue a warning.
Signed-off-by Ilya Leoshkevich <[email protected]>--- arch/s390/boot/ipl_parm.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-)arch/s390/boot/ipl_parm.c +0
-0@@ -173,12 +173,29 @@ static inline int has_ebcdic_char(const char *str)return 0 ; }
arch/s390/boot/ipl_parm.c static inline int has_ebcdic_char(const char *str) · line 185
Quoted 10 lines
arch/s390/boot/ipl_parm.c +10
-0+static inline int has_nonprintable_char (const char *str) +{ +int i; + +for (i =0 ; str[i]; i++) { +unsigned char c = (unsigned char )str[i]; + +/* isprint() is Latin-1, and we need ASCII here */ +if (c <0x20 || c >0x7e ) +return 1 ;
Hm, I guess the comment refers to a different implementation than the kernel internal one? Since isprint() (see include/linux/ctype.h) is true for exactly the range you open-coded, as far as I can tell.
Furthermore kernel command line parsing also allows for all sorts of spaces, tabs, and line feeds (see e.g. next_arg()). So I guess the above should be changed (and shortened :) ) to something like:
static inline int has_nonprintable_char(const char *str)
{
for (int i = 0; str[i]; i++) {
if (isprint(str[i]) || isspace(str[i]))
return 1;
}
return 0;
}Quoted 8 lines · On Tue, 25 Aug 2026 17:08:08 +0200 Ilya Leoshkevich <[email protected]> wrote:
Users may accidentally add multi-byte UTF-8 characters to zipl.conf parmline, for example, by copying snippets containing non-breaking spaces (\xC2\xA0) from web pages.
The kernel will then interpret the entire command line as EBCDIC, making it unusable. Distinguish this situation from the legitimate EBCDIC conversion by looking for non-printable characters and issue a warning.
Would it be better to check for the entire line being printable ebcdic? All of EBCDIC a-zA-Z0-9 have the 0x80 bit set and most of 0x20..0x7f are invalid or control characters (or punctuation).
David
Quoted 41 lines
Signed-off-by Ilya Leoshkevich <[email protected]>--- arch/s390/boot/ipl_parm.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-)arch/s390/boot/ipl_parm.c +18
-1@@ -173,12 +173,29 @@ static inline int has_ebcdic_char(const char *str)return 0 ; } +static inline int has_nonprintable_char (const char *str) +{ +int i; + +for (i =0 ; str[i]; i++) { +unsigned char c = (unsigned char )str[i]; + +/* isprint() is Latin-1, and we need ASCII here */ +if (c <0x20 || c >0x7e ) +return 1 ; + } +return 0 ; +} +void setup_boot_command_line (void ) { parmarea.command_line[COMMAND_LINE_SIZE -1 ] =0 ;/* convert arch command line to ascii if necessary */ -if (has_ebcdic_char (parmarea.command_line)) +if (has_ebcdic_char (parmarea.command_line)) {EBCASC (parmarea.command_line,COMMAND_LINE_SIZE ); +if (has_nonprintable_char (parmarea.command_line)) +boot_warn ("Kernel command line was treated as EBCDIC, but contains non-printable characters\n" ); + }/* copy arch command line */ strscpy (early_command_line,strim (parmarea.command_line));
Quoted 12 lines · David Laight
Quoted 8 lines · On Tue, 25 Aug 2026 17:08:08 +0200 Ilya Leoshkevich <[email protected]> wrote:
Users may accidentally add multi-byte UTF-8 characters to zipl.conf parmline, for example, by copying snippets containing non-breaking spaces (\xC2\xA0) from web pages.
The kernel will then interpret the entire command line as EBCDIC, making it unusable. Distinguish this situation from the legitimate EBCDIC conversion by looking for non-printable characters and issue a warning.
Quoted 5 lines
Would it be better to check for the entire line being printable ebcdic? All of EBCDIC a-zA-Z0-9 have the
0x80bit set and most of 0x20..0x7f are invalid or control characters (or punctuation).David
I actually started with that, but this required introducing a new _ctype-like table (unfortunately it's not as simple as checking a couple ranges), so I decided against that and took a shortcut via ASCII.
[...]
Quoted 23 lines · Heiko Carstens
Quoted 22 lines · Ilya Leoshkevich
Users may accidentally add multi-byte UTF-8 characters to zipl.conf parmline, for example, by copying snippets containing non-breaking spaces (\xC2\xA0) from web pages.
The kernel will then interpret the entire command line as EBCDIC, making it unusable. Distinguish this situation from the legitimate EBCDIC conversion by looking for non-printable characters and issue a warning.
Signed-off-by Ilya Leoshkevich <[email protected]>--- arch/s390/boot/ipl_parm.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-)arch/s390/boot/ipl_parm.c +0
-0@@ -173,12 +173,29 @@ static inline int has_ebcdic_char(const char *str)return 0 ; }
Quoted 14 lines
arch/s390/boot/ipl_parm.c static inline int has_ebcdic_char(const char *str) · line 185
Quoted 10 lines
arch/s390/boot/ipl_parm.c +10
-0+static inline int has_nonprintable_char (const char *str) +{ +int i; + +for (i =0 ; str[i]; i++) { +unsigned char c = (unsigned char )str[i]; + +/* isprint() is Latin-1, and we need ASCII here */ +if (c <0x20 || c >0x7e ) +return 1 ;Hm, I guess the comment refers to a different implementation than the kernel internal one? Since
isprint()(seeinclude/linux/ctype.h) is true for exactly the range you open-coded, as far as I can tell.
Unfortunately isprint() matches some extra ASCII upper-half characters, e.g.:
const unsigned char _ctype[] = {
[...]
_P,_P,_P,_P,_P,_P,_P,_P,_P,_P,_P,_P,_P,_P,_P,_P, /* 176-191 */Quoted 3 lines
Furthermore kernel command line parsing also allows for all sorts of spaces, tabs, and line feeds (see e.g.
next_arg()). So I guess the above should be changed (and shortened :) ) to something like:
I completely forgot about newlines, thanks!
Quoted 8 lines
static inline int
has_nonprintable_char(const char *str){ for (int i = 0; str[i]; i++) { if (isprint(str[i]) || isspace(str[i])) return 1; } return 0; }
Quoted 17 lines · On Wed, 26 Aug 2026 16:08:50 +0200 Ilya Leoshkevich <[email protected]> wrote:
Quoted 16 lines · David Laight
Quoted 8 lines · On Tue, 25 Aug 2026 17:08:08 +0200 Ilya Leoshkevich <[email protected]> wrote:
Users may accidentally add multi-byte UTF-8 characters to zipl.conf parmline, for example, by copying snippets containing non-breaking spaces (\xC2\xA0) from web pages.
The kernel will then interpret the entire command line as EBCDIC, making it unusable. Distinguish this situation from the legitimate EBCDIC conversion by looking for non-printable characters and issue a warning.
Would it be better to check for the entire line being printable ebcdic? All of EBCDIC a-zA-Z0-9 have the
0x80bit set and most of 0x20..0x7f are invalid or control characters (or punctuation).
Quoted 6 lines
Quoted 1 line
David
I actually started with that, but this required introducing a new _ctype-like table (unfortunately it's not as simple as checking a couple ranges), so I decided against that and took a shortcut via ASCII.
Could you get the conversion function to return an error if it found invalid EBCDIC characters?
If there is a single UTF8 character (eg non-breaking space) you really want to treat the line as ASCII.
Actually you could count the number of characters with the 0x80 bit set. If more than 1/2 assume EBCDIC (all of 0-9a-zA-Z have the bit set).
(I didn't realise anyone still used EBCDIC.
I guess the unix implementation(s) use ASCII (otherwise too much code is broken) but the old IBM OS uses EBCDIC.
I worked for ICL for a while, their old 1900 series (from the early 1970s) used 6bit characters (4 in a 24bit word) that were ACSII codes 32-95. The replacement 2900 series (very late 1970s) used EBCDIC internally (I guess because IBM used it...) but all the peripherals were ASCII.)
David
Quoted 2 lines
[...]
Quoted 27 lines · David Laight
Quoted 17 lines · On Wed, 26 Aug 2026 16:08:50 +0200 Ilya Leoshkevich <[email protected]> wrote:
Quoted 16 lines · David Laight
Quoted 8 lines · On Tue, 25 Aug 2026 17:08:08 +0200 Ilya Leoshkevich <[email protected]> wrote:
Users may accidentally add multi-byte UTF-8 characters to zipl.conf parmline, for example, by copying snippets containing non-breaking spaces (\xC2\xA0) from web pages.
The kernel will then interpret the entire command line as EBCDIC, making it unusable. Distinguish this situation from the legitimate EBCDIC conversion by looking for non-printable characters and issue a warning.
Would it be better to check for the entire line being printable ebcdic? All of EBCDIC a-zA-Z0-9 have the
0x80bit set and most of 0x20..0x7f are invalid or control characters (or punctuation).Quoted 6 lines
Quoted 1 line
David
I actually started with that, but this required introducing a new _ctype-like table (unfortunately it's not as simple as checking a couple ranges), so I decided against that and took a shortcut via ASCII.
Quoted 6 lines
Could you get the conversion function to return an error if it found invalid EBCDIC characters?
If there is a single UTF8 character (eg non-breaking space) you really want to treat the line as ASCII.
Actually you could count the number of characters with the0x80bit set. If more than 1/2 assume EBCDIC (all of 0-9a-zA-Z have the bit set).
I also considered that, but setting any threshold feels arbitrary and will probably fail for punctuation-heavy command lines.
I also didn't want to make it a hard fail, because I'm not certain that I know all uses cases. Perhaps there are people who wants umlauts and what not? It would be bad to break whatever they are doing.
But at the same time it was very painful to debug the issue, so I settled for the compromise: add a warning that will be helpful to 99.9% users and will only mildly annoy the 0.1% umlaut users.
I just had an off-list discussion with Heiko and we think about going with your first proposal for v3: a new _ctype table for EBCDIC for determining whether characters are printable. The overhead from this is not bad as I thought it would be.
Quoted 7 lines
(I didn't realise anyone still used EBCDIC.
I guess the unix implementation(s) use ASCII (otherwise too much code is broken) but the old IBM OS uses EBCDIC.
I worked for ICL for a while, their old 1900 series (from the early 1970s) used 6bit characters (4 in a 24bit word) that were ACSII codes 32-95. The replacement 2900 series (very late 1970s) used EBCDIC internally (I guess because IBM used it...) but all the peripherals were ASCII.)
Linux on s390 still uses it for interfacing with traditional IBM hypervisors (z/VM and PR/SM), which are very much alive and used today.
Quoted 5 lines
David
Quoted 2 lines
[...]