Skip to contentSkip to conversation

Allocating a frame buffer in memory

U-Boot Steven Zedeck 2 participants 2 messages Apr 10, 2009 – Apr 17, 2009

lore
Share & tools
lore
#0 lore raw

Hi,
I am trying to allocate a frame buffer for my LCD code. I think I understand how to set up the LCC controller in the Atmel AT91SAM9. So thats not the issue, at least not yet. I need to understand how UBoot allocates a block of memory for the buffer.

My TFT/LCD is 320x240 and in 24 bit mode, so 3 bytes per pixel. So I think I need 320x240x3 total bytes. Correct?

In my lib_arm/board.c file, there is the following:

#ifdef CONFIG_LCD
	/* board init may have inited fb_base */
	if (!gd->fb_base) {
#		ifndef PAGE_SIZE
#		  define PAGE_SIZE 4096
#		endif
		/*
		 * reserve memory for LCD display (always full pages)
		 */
		/* bss_end is defined in the board-specific linker script */
		addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
		size = lcd_setmem (addr);
		gd->fb_base = addr;
	}

#endif /* CONFIG_LCD */

Then in lcd.c, there is lcd_setmem which displays:
Reserving 600k for LCD Framebuffer at: 0x23E91000

Even though I call lcd_setmem with an address of: 0x23F27000

Which is the address that I pass to the Atmel LCD controller DMA Address ? I have been using this: 0x23F27000

Thanks,
Steve

Signature · 2 lines
View this message in context: http://www.nabble.com/Allocating-a-frame-buffer-in-memory-tp22993711p22993711.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#1 lore raw
Quoted 27 lines · Steven Zedeck

Hi,
I am trying to allocate a frame buffer for my LCD code. I think I understand how to set up the LCC controller in the Atmel AT91SAM9. So thats not the issue, at least not yet. I need to understand how UBoot allocates a block of memory for the buffer.

My TFT/LCD is 320x240 and in 24 bit mode, so 3 bytes per pixel. So I think I need 320x240x3 total bytes. Correct?

In my lib_arm/board.c file, there is the following:

#ifdef CONFIG_LCD
	/* board init may have inited fb_base */
	if (!gd->fb_base) {
#		ifndef PAGE_SIZE
#		  define PAGE_SIZE 4096
#		endif
		/*
		 * reserve memory for LCD display (always full pages)
		 */
		/* bss_end is defined in the board-specific linker script */
		addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
		size = lcd_setmem (addr);
		gd->fb_base = addr;
	}

#endif /* CONFIG_LCD */

Quoted 7 lines

Then in lcd.c, there is lcd_setmem which displays:
Reserving 600k for LCD Framebuffer at: 0x23E91000

Even though I call lcd_setmem with an address of: 0x23F27000

Which is the address that I pass to the Atmel LCD controller DMA Address ? I have been using this: 0x23F27000

on at91sam9 to specify the frambuffer base address you will just need to fill
gd->fb_base = AT91SAM9263_SRAM0_BASE;
or something else as done with the PSRAM for the pm9263
in your board init and specify your "vidinfo_t panel_info" that's all (maybe you will need to check the LCD pin out configuration)

Best Regards,
J.