MPC8245 custom board, Linux 2.4 kernel hangs after uncompressing
Hi
I am trying to run Embedded linux (ELDK) (2.4 kerenl) on a custom powerpc b= oard,
which is similar to Artis A3000 board. This board has mpc8245(XPC8245LZY266B), natsemi 83815 ethernet, 4MB intel e28f320 flash, 16MB winbond w986432DH-6 SDRAM. So I configured and compiled U-boot for A3000 borad. U-boot worked on my board also. Next I compiled ELDK 3.0 for Sandpoint 8245 board and copied to flash. But linux hangs after uncompressing
U-Boot 1.1.2 (Apr 14 2005 - 00:02:29)
CPU: MPC8245 Revision 1.2 at 249.999 MHz: 16 kB I-Cache 16 kB D-Cache Board: A3000 Local Bus at 99.999 MHz I2C: ready DRAM: 16 MB FLASH: Get flash bank 0 @ 0xffc00000
Manuf. ID @ 0xff800000: 0x00000089
Device ID @ 0xff800001: 0x00000016
## Flash bank 0 at 0xffc00000 sizes: 0x00400000
protect monitor fff00000 @ 40000
protect environtment fffc0000 @ 20000
## Final Flash bank sizes: 00400000
4 MB
00 13 100b 0020 0200 ff In: serial Out: serial Err: serial Net: natsemi: EEPROM contents:
ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff dp83815#0
Warning: dp83815#0 MAC addresses don't match:
Address in SROM is FF:FF:FF:FF:FF:FF
Address in environment is 00:40:05:B0:F1:BA
A3000> tftpboot 400000 uImage.eldk
Using dp83815#0 device
TFTP from server 192.168.1.124; our IP address is 192.168.1.54 Filename 'uImage.eldk'.
Load address: 0x400000
Loading: #################################################################
#################################################################
###################done
Bytes transferred =3D 757926 (b90a6 hex)
A3000> bootm
## Booting image at 00400000 ...
Image Name: Linux-2.4.25 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 757862 Bytes =3D 740.1 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
nothing happens after this until I reboot the board. I read u-boot FAQ and configured bd_info structure same for both u-boot and Linux. I found that CFG_IMMR is not applicable to MPC8245. I also used clocks_in_mhz variable also before loading Linux. I am stuck here. Could you please let me know what should I do next?
Thanks
Kishore
Quoted 3 lines · Kishore Devireddy
Hi
=20
I am trying to run Embedded linux (ELDK) (2.4 kerenl) on a custom powerpc=
board,
Quoted 26 lines
which is similar to Artis A3000 board. This board has mpc8245(XPC8245LZY266B), natsemi 83815 ethernet, 4MB intel e28f320 flash, 16MB winbond w986432DH-6 SDRAM. So I configured and compiled U-boot for A3000 borad. U-boot worked on my board also. Next I compiled ELDK 3.0 for Sandpoint 8245 board and copied to flash. But linux hangs after uncompressing
=20
U-Boot 1.1.2 (Apr 14 2005 - 00:02:29)
=20CPU: MPC8245 Revision 1.2 at 249.999 MHz: 16 kB I-Cache 16 kB D-Cache Board: A3000 Local Bus at 99.999 MHz I2C: ready DRAM: 16 MB FLASH: Get flash bank 0 @ 0xffc00000Manuf. ID @
0xff800000:0x00000089
Device ID @0xff800001:0x00000016
## Flash bank 0 at0xffc00000sizes:0x00400000
protect monitorfff00000@ 40000
protect environtmentfffc0000@ 20000
## Final Flash bank sizes: 00400000
4 MB00 13 100b 0020 0200 ff In: serial Out: serial Err: serial Net: natsemi: EEPROM contents:
Quoted 12 lines
ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff dp83815#0
Warning: dp83815#0 MAC addresses don't match:
Address in SROM is FF:FF:FF:FF:FF:FF
Address in environment is 00:40:05:B0:F1:BA
=20
A3000> tftpboot 400000 uImage.eldk
Using dp83815#0 device
TFTP from server 192.168.1.124; our IP address is 192.168.1.54 Filename 'uImage.eldk'.
Load address:0x400000
Loading: ################################################################=
#
Quoted 9 lines
################################################################# ###################done
Bytes transferred =3D 757926 (b90a6 hex)
A3000> bootm
## Booting image at 00400000 ...Image Name: Linux-2.4.25 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 757862 Bytes =3D 740.1 kB
Quoted 10 lines
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
=20
nothing happens after this until I reboot the board. I read u-boot FAQ and configuredbd_infostructure same for both u-boot and Linux. I found thatCFG_IMMRis not applicable to MPC8245. I also usedclocks_in_mhzvariable also before loading Linux. I am stuck here. Could you please let me know what should I do next?
Quick check; Try 'printenv' in u-boot. Make sure that 'bootargs' specifies a console. ie "bootargs=3Dconsole=3DttyS0,115200 root=3D/dev/nfs ..."
g.