Skip to contentSkip to conversation

MPC8245 custom board, Linux 2.4 kernel hangs after uncompressing

DISCUSSION Kishore Devireddy 2 participants 2 messages Apr 21, 2005 – Apr 22, 2005

lore
Share & tools
lore
#0 lore raw

Hi

I am trying to run Embedded linux (ELDK) (2.4 kerenl) on a custom powerpc b= oard,
which is similar to Artis A3000 board. This board has mpc8245(XPC8245LZY266B), natsemi 83815 ethernet, 4MB intel e28f320 flash, 16MB winbond w986432DH-6 SDRAM. So I configured and compiled U-boot for A3000 borad. U-boot worked on my board also. Next I compiled ELDK 3.0 for Sandpoint 8245 board and copied to flash. But linux hangs after uncompressing

U-Boot 1.1.2 (Apr 14 2005 - 00:02:29)

CPU:   MPC8245 Revision 1.2 at 249.999 MHz: 16 kB I-Cache 16 kB D-Cache
Board: A3000 Local Bus at 99.999 MHz
I2C:   ready
DRAM:  16 MB
FLASH: Get flash bank 0 @ 0xffc00000

Manuf. ID @ 0xff800000: 0x00000089
Device ID @ 0xff800001: 0x00000016
## Flash bank 0 at 0xffc00000 sizes: 0x00400000
protect monitor fff00000 @ 40000
protect environtment fffc0000 @ 20000
## Final Flash bank sizes: 00400000
4 MB

      00  13  100b  0020  0200  ff
In:    serial
Out:   serial
Err:   serial
Net:   natsemi: EEPROM contents:

ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff dp83815#0
Warning: dp83815#0 MAC addresses don't match:
Address in SROM is FF:FF:FF:FF:FF:FF
Address in environment is 00:40:05:B0:F1:BA

A3000> tftpboot 400000 uImage.eldk
Using dp83815#0 device
TFTP from server 192.168.1.124; our IP address is 192.168.1.54 Filename 'uImage.eldk'.
Load address: 0x400000
Loading: #################################################################

       #################################################################
       ###################

done
Bytes transferred =3D 757926 (b90a6 hex)
A3000> bootm
## Booting image at 00400000 ...

 Image Name:   Linux-2.4.25
 Image Type:   PowerPC Linux Kernel Image (gzip compressed)
 Data Size:    757862 Bytes =3D 740.1 kB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

nothing happens after this until I reboot the board. I read u-boot FAQ and configured bd_info structure same for both u-boot and Linux. I found that CFG_IMMR is not applicable to MPC8245. I also used clocks_in_mhz variable also before loading Linux. I am stuck here. Could you please let me know what should I do next?

Thanks
Kishore

#1 lore raw
Quoted 3 lines · Kishore Devireddy

Hi
=20
I am trying to run Embedded linux (ELDK) (2.4 kerenl) on a custom powerpc=

board,

Quoted 26 lines

which is similar to Artis A3000 board. This board has mpc8245(XPC8245LZY266B), natsemi 83815 ethernet, 4MB intel e28f320 flash, 16MB winbond w986432DH-6 SDRAM. So I configured and compiled U-boot for A3000 borad. U-boot worked on my board also. Next I compiled ELDK 3.0 for Sandpoint 8245 board and copied to flash. But linux hangs after uncompressing
=20
U-Boot 1.1.2 (Apr 14 2005 - 00:02:29)
=20

CPU:   MPC8245 Revision 1.2 at 249.999 MHz: 16 kB I-Cache 16 kB D-Cache
Board: A3000 Local Bus at 99.999 MHz
I2C:   ready
DRAM:  16 MB
FLASH: Get flash bank 0 @ 0xffc00000

Manuf. ID @ 0xff800000: 0x00000089
Device ID @ 0xff800001: 0x00000016
## Flash bank 0 at 0xffc00000 sizes: 0x00400000
protect monitor fff00000 @ 40000
protect environtment fffc0000 @ 20000
## Final Flash bank sizes: 00400000
4 MB

      00  13  100b  0020  0200  ff
In:    serial
Out:   serial
Err:   serial
Net:   natsemi: EEPROM contents:
Quoted 12 lines

ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff dp83815#0
Warning: dp83815#0 MAC addresses don't match:
Address in SROM is FF:FF:FF:FF:FF:FF
Address in environment is 00:40:05:B0:F1:BA
=20
A3000> tftpboot 400000 uImage.eldk
Using dp83815#0 device
TFTP from server 192.168.1.124; our IP address is 192.168.1.54 Filename 'uImage.eldk'.
Load address: 0x400000
Loading: ################################################################=

#

Quoted 9 lines
       #################################################################
       ###################

done
Bytes transferred =3D 757926 (b90a6 hex)
A3000> bootm
## Booting image at 00400000 ...

 Image Name:   Linux-2.4.25
 Image Type:   PowerPC Linux Kernel Image (gzip compressed)
 Data Size:    757862 Bytes =3D 740.1 kB
Quoted 10 lines

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
=20
nothing happens after this until I reboot the board. I read u-boot FAQ and configured bd_info structure same for both u-boot and Linux. I found that CFG_IMMR is not applicable to MPC8245. I also used clocks_in_mhz variable also before loading Linux. I am stuck here. Could you please let me know what should I do next?

Quick check; Try 'printenv' in u-boot. Make sure that 'bootargs' specifies a console. ie "bootargs=3Dconsole=3DttyS0,115200 root=3D/dev/nfs ..."

g.