Skip to contentSkip to conversation

CD-ROM and HDD problems with the VIA chipset driver, MB Asus A7M266

DISCUSSION Jack Jørgensen 1 participant 1 message Sep 24, 2001

lore
Share & tools
lore
#0 lore raw

Hello!

I'm having some problems using the following setup:

SCSI emulation on my CD-rom's (SCSI emulation, SCSI support, SCSI cdrom support and SCSI generic driver) The CD-rom's are (on ide1):
PLEXTOR CD-R PX-W1610A (master)
CREATIVE DVD-ROM DVD6240E (slave)
I also have two hdd's (on ide0):
IBM DeskStar 60GXP 40GB (master)
Seagate ST315320A (slave)

My motherboard is the Asus A7M266 (with the Via VT82C686B south-bridge)

The kernel is 2.4.2

Now, if I don't include via chipset support, my hdd's run at ATA100 (IBM) and ATA66 (Seagate). If i include the via chipset, they both run at ATA33, which I can't change.

When not using the via chipset support, my Plextor drive won't mount cd's (the creative cd-rom works fine in both modes) though it still burns fine.

/var/log/messages include:
ide-scsi: The scsi wants to send us more data than expected -
discarding data
68 times

and right after:
can't determine CD-Format.

when i try to mount

If I include the via chipset support, the cd mounts with Plextor, but the hdd's (as already stated) runs slower (about 10MB/s)

Also, the information in /proc/ide/via:
----------VIA BusMastering IDE Configuration----------------

Driver Version:                     3.20
South Bridge:                       VIA vt82c686b
Revision:                           ISA 0x40 IDE 0x6
BM-DMA base:                        0xd800
PCI clock:                          33MHz
Master Read  Cycle IRDY:            0ws
Master Write Cycle IRDY:            0ws
BM IDE Status Register Read Retry:  yes
Max DRDY Pulse Width:               No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush:          yes                 yes
End Sector FIFO flush:         no                  no
Prefetch Buffer:              yes                  no
Post Write Buffer:            yes                  no
Enabled:                      yes                 yes
Simplex only:                  no                  no
Cable Type:                   40w                 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode:       UDMA      UDMA      UDMA      UDMA
Address Setup:       30ns      30ns      30ns      30ns
Cmd Active:          90ns      90ns      90ns      90ns
Cmd Recovery:        30ns      30ns      30ns      30ns
Data Active:         90ns      90ns      90ns      90ns
Data Recovery:       30ns      30ns      30ns      30ns
Cycle Time:          60ns      60ns      90ns      90ns
Transfer Rate:   33.3MB/s  33.3MB/s  22.2MB/s  22.2MB/s

Dosen't fit with the cables I use - they are both 80 pins (and the BIOS acknowledges this)

hdparm -i /dev/hd[ab] (when using the via chipset support):
/dev/hda:

Model=IC35L040AVER07-0, FwRev=ER4OA44A, SerialNo=SXPTX0K2690 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40 BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=80418240 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5

/dev/hdb:

Model=ST315320A, FwRev=3.12, SerialNo=3CW035CJ
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=29888820 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4

I tried using the via kernel parameter to hardcode the UDMA transfer-rates but nothing happend.

(I'm not subscribed to this list, so if anybody answers would they please CC the reply to me) Kind regards Jack Jørgensen.

----
This is a signature virus!
Copy this into you're ~/.signature file to help it spread