CD-ROM and HDD problems with the VIA chipset driver, MB Asus A7M266
Hello!
I'm having some problems using the following setup:
SCSI emulation on my CD-rom's (SCSI emulation, SCSI support, SCSI cdrom support and SCSI generic driver) The CD-rom's are (on ide1):
PLEXTOR CD-R PX-W1610A (master)
CREATIVE DVD-ROM DVD6240E (slave)
I also have two hdd's (on ide0):
IBM DeskStar 60GXP 40GB (master)
Seagate ST315320A (slave)
My motherboard is the Asus A7M266 (with the Via VT82C686B south-bridge)
The kernel is 2.4.2
Now, if I don't include via chipset support, my hdd's run at ATA100 (IBM) and ATA66 (Seagate). If i include the via chipset, they both run at ATA33, which I can't change.
When not using the via chipset support, my Plextor drive won't mount cd's (the creative cd-rom works fine in both modes) though it still burns fine.
/var/log/messages include:
ide-scsi: The scsi wants to send us more data than expected -
discarding data
68 times
and right after:
can't determine CD-Format.
when i try to mount
If I include the via chipset support, the cd mounts with Plextor, but the hdd's (as already stated) runs slower (about 10MB/s)
Also, the information in /proc/ide/via:
----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.20 South Bridge: VIA vt82c686b Revision: ISA 0x40 IDE 0x6 BM-DMA base: 0xd800 PCI clock: 33MHz Master Read Cycle IRDY: 0ws Master Write Cycle IRDY: 0ws BM IDE Status Register Read Retry: yes Max DRDY Pulse Width: No limit -----------------------Primary IDE-------Secondary IDE------ Read DMA FIFO flush: yes yes End Sector FIFO flush: no no Prefetch Buffer: yes no Post Write Buffer: yes no Enabled: yes yes Simplex only: no no Cable Type: 40w 40w -------------------drive0----drive1----drive2----drive3----- Transfer Mode: UDMA UDMA UDMA UDMA Address Setup: 30ns 30ns 30ns 30ns Cmd Active: 90ns 90ns 90ns 90ns Cmd Recovery: 30ns 30ns 30ns 30ns Data Active: 90ns 90ns 90ns 90ns Data Recovery: 30ns 30ns 30ns 30ns Cycle Time: 60ns 60ns 90ns 90ns Transfer Rate: 33.3MB/s 33.3MB/s 22.2MB/s 22.2MB/s
Dosen't fit with the cables I use - they are both 80 pins (and the BIOS acknowledges this)
hdparm -i /dev/hd[ab] (when using the via chipset support):/dev/hda:
Model=IC35L040AVER07-0, FwRev=ER4OA44A, SerialNo=SXPTX0K2690 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40 BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=80418240 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
/dev/hdb:
Model=ST315320A, FwRev=3.12, SerialNo=3CW035CJ
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=29888820 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
I tried using the via kernel parameter to hardcode the UDMA transfer-rates but nothing happend.
(I'm not subscribed to this list, so if anybody answers would they please CC the reply to me) Kind regards Jack Jørgensen.
----
This is a signature virus!
Copy this into you're ~/.signature file to help it spread