Skip to contentSkip to conversation

Net device queries.

DISCUSSION Bill Leckey 2 participants 2 messages Nov 10, 2002 – Nov 11, 2002

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

I've been coding an ethernet driver for some new hardware we're
developing and while it's working, there are a few issues I'm still
unsure of. I couldn't find any archives for this list, so I'm
suspecting I'm going to cover a lot of 'old ground'. Most of my info for coding ethernet drivers comes out of Rubini and Corbet's LInux Device Drivers, and what I've gleaned from kernel sources

Firstly some background. With these cards I can have up to 25 point to point connections (to the same destination machine, or 25 destination machines). I have almost total control of what goes out on the wire, so I've chosen a minimal header that contains the type (passed in to hard_header) and a 16 bit field that contains misc other information. So, 32 bits, plus the data. The hardware provides things like length, and CRC checking.

Currently I'm setting dev->hard_header_len to 4.

The part that concerns me is what I set dev->type, dev->addr_len and dev->flags to.

We don't technically have a hardware address so I set dev->addr_len to 0.

I set dev->type to ARPHRD_VOID, simply because I'm not sure what the consequences of setting it to anything else are.

I set dev->flags to IFF_POINTOPOINT | IFF_NOARP

This appears to all work correctly, however both ifconfig and tcpdump aren't really happy.

TCPDUMP doesn't know what to do with the ARPHRD_VOID and drops to 'raw' mode, so it still does what I need, even if it prints an annoying message for each packet.

ifconfig isn't sure what to do about the HWaddr. For instance, this is the ifconfig for one of the links:

hssl0 Link encap:UNSPEC HWaddr
00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00

           inet addr:192.168.2.1  P-t-P:192.168.2.2  Mask:255.255.255.255
           UP POINTOPOINT RUNNING NOARP  MTU:1500  Metric:1
           RX packets:3509748 errors:459 dropped:0 overruns:0 frame:363
           TX packets:3013210 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:100
           RX bytes:368907445 (351.8 Mb)  TX bytes:266074976 (253.7 Mb)

Any thoughts, comments or otherwise on what I've done, or what I /should/ be doing would be appreciated as I'm still not fully across how the networking stuff works.

Bill

Signature · 7 lines
Bill Leckey - Senior Software Design Engineer
TPG Research and Development
Ph: +61 2 62851711
Fax: +61 2 62853939


.
#1 lore raw
Quoted 13 lines · Bill Leckey

I've been coding an ethernet driver for some new hardware we're
developing and while it's working, there are a few issues I'm still
unsure of. I couldn't find any archives for this list, so I'm
suspecting I'm going to cover a lot of 'old ground'. Most of my info for coding ethernet drivers comes out of Rubini and Corbet's LInux Device Drivers, and what I've gleaned from kernel sources

Firstly some background. With these cards I can have up to 25 point to point connections (to the same destination machine, or 25 destination machines). I have almost total control of what goes out on the wire, so I've chosen a minimal header that contains the type (passed in to hard_header) and a 16 bit field that contains misc other information. So, 32 bits, plus the data. The hardware provides things like length, and CRC checking.

Quoted 6 lines

Currently I'm setting dev->hard_header_len to 4.

The part that concerns me is what I set dev->type, dev->addr_len and dev->flags to.

We don't technically have a hardware address so I set dev->addr_len to 0.

If you want to look like ethernet, it seems you would want at least a fake MAC. To me, it also sounds like you may want up to 25 net_devices, since you have that many logical point-to-point connections. (Similar to the way VLAN works)

Quoted 3 lines

I set dev->type to ARPHRD_VOID, simply because I'm not sure what the consequences of setting it to anything else are.

Maybe you could get a serial number out of your device and then hash it into MAC addresses? The user can always change these with ifconfig or 'ip' after your device initializes anyway...

Signature · 3 lines
Ben Greear <[email protected]>       <Ben_Greear AT excite.com>
President of Candela Technologies Inc      http://www.candelatech.com
ScryMUD:  http://scry.wanfear.com     http://scry.wanfear.com/~greear