Net device queries.
Subsystems (2)
I've been coding an ethernet driver for some new hardware we're
developing and while it's working, there are a few issues I'm still
unsure of. I couldn't find any archives for this list, so I'm
suspecting I'm going to cover a lot of 'old ground'. Most of my info for coding ethernet drivers comes out of Rubini and Corbet's LInux Device Drivers, and what I've gleaned from kernel sources
Firstly some background. With these cards I can have up to 25 point to point connections (to the same destination machine, or 25 destination machines). I have almost total control of what goes out on the wire, so I've chosen a minimal header that contains the type (passed in to hard_header) and a 16 bit field that contains misc other information. So, 32 bits, plus the data. The hardware provides things like length, and CRC checking.
Currently I'm setting dev->hard_header_len to 4.
The part that concerns me is what I set dev->type, dev->addr_len and dev->flags to.
We don't technically have a hardware address so I set dev->addr_len to 0.
I set dev->type to ARPHRD_VOID, simply because I'm not sure what the consequences of setting it to anything else are.
I set dev->flags to IFF_POINTOPOINT | IFF_NOARP
This appears to all work correctly, however both ifconfig and tcpdump aren't really happy.
TCPDUMP doesn't know what to do with the ARPHRD_VOID and drops to 'raw' mode, so it still does what I need, even if it prints an annoying message for each packet.
ifconfig isn't sure what to do about the HWaddr. For instance, this is the ifconfig for one of the links:
hssl0 Link encap:UNSPEC HWaddr
00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:192.168.2.1 P-t-P:192.168.2.2 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:3509748 errors:459 dropped:0 overruns:0 frame:363
TX packets:3013210 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:368907445 (351.8 Mb) TX bytes:266074976 (253.7 Mb)Any thoughts, comments or otherwise on what I've done, or what I /should/ be doing would be appreciated as I'm still not fully across how the networking stuff works.
Bill
Signature · 7 lines
Bill Leckey - Senior Software Design Engineer TPG Research and Development Ph: +61 2 62851711 Fax: +61 2 62853939 .
Quoted 13 lines · Bill Leckey
I've been coding an ethernet driver for some new hardware we're
developing and while it's working, there are a few issues I'm still
unsure of. I couldn't find any archives for this list, so I'm
suspecting I'm going to cover a lot of 'old ground'. Most of my info for coding ethernet drivers comes out of Rubini and Corbet's LInux Device Drivers, and what I've gleaned from kernel sourcesFirstly some background. With these cards I can have up to 25 point to point connections (to the same destination machine, or 25 destination machines). I have almost total control of what goes out on the wire, so I've chosen a minimal header that contains the type (passed in to
hard_header) and a 16 bit field that contains misc other information. So, 32 bits, plus the data. The hardware provides things like length, and CRC checking.
Quoted 6 lines
Currently I'm setting
dev->hard_header_lento 4.The part that concerns me is what I set
dev->type,dev->addr_lenanddev->flagsto.We don't technically have a hardware address so I set
dev->addr_lento 0.
If you want to look like ethernet, it seems you would want at least a fake MAC. To me, it also sounds like you may want up to 25 net_devices, since you have that many logical point-to-point connections. (Similar to the way VLAN works)
Quoted 3 lines
I set
dev->typetoARPHRD_VOID, simply because I'm not sure what the consequences of setting it to anything else are.
Maybe you could get a serial number out of your device and then hash it into MAC addresses? The user can always change these with ifconfig or 'ip' after your device initializes anyway...
Signature · 3 lines
Ben Greear <[email protected]> <Ben_Greear AT excite.com> President of Candela Technologies Inc http://www.candelatech.com ScryMUD: http://scry.wanfear.com http://scry.wanfear.com/~greear