Skip to contentSkip to conversation

RAID1 problem, newbie to RAID

DISCUSSION J Dalessandro 2 participants 2 messages Jan 20, 2003 – Jan 21, 2003 MD RAID

lore
Share & tools
lore
#0 lore raw

I am trying to get RAID1 working on a Debian machine with a 2.4.20 kernel. I hope I am close, but this is my first attempt at RAID on any platform.

I seem to get two out of three partitions. I think my problem is in that my "/" partition is mounted, but I'm new to RAID and I'm not sure how to fix this issue. Below is my: /proc/mdstat, raidtab, fdisk -l outputs. What am I missing here to solve my bungled configuration?

CM:~# cat /proc/mdstat
Personalities : [raid1]
read_ahead 1024 sectors
md0 : active raid1 hda1[0]
      96256 blocks [2/1] [U_]

md1 : active raid1 hda2[0]

      9767424 blocks [2/1] [U_]

unused devices: <none>

CM:~# cat /etc/raidtab
raiddev /dev/md2
        raid-level              1
        nr-raid-disks           2
        nr-spare-disks          0
        chunk-size              32
        persistent-superblock   1
        device                  /dev/hda3
        raid-disk               0
        device                  /dev/hdc3
        failed-disk             1

raiddev /dev/md1

        raid-level              1
        nr-raid-disks           2
        nr-spare-disks          0
        chunk-size              32
        persistent-superblock   1
        device                  /dev/hda2
        raid-disk               0
        device                  /dev/hdc2
        failed-disk             1

raiddev /dev/md0

        raid-level              1
        nr-raid-disks           2
        nr-spare-disks          0
        chunk-size              32
        persistent-superblock   1
        device                  /dev/hda1
        raid-disk               0
        device                  /dev/hdc1
        failed-disk             1
CM:~# df -k
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/hda3             86437648    480844  81565840   1% /
CM:~# fdisk -l

Disk /dev/hdc: 255 heads, 63 sectors, 12161 cylinders Units = cylinders of 16065 * 512 bytes

   Device Boot    Start       End    Blocks   Id  System
/dev/hdc1             1        12     96358+  fd  Linux raid autodetect
/dev/hdc2            13      1228   9767520   fd  Linux raid autodetect
/dev/hdc3          1229     12161  87819322+  fd  Linux raid autodetect

Disk /dev/hda: 255 heads, 63 sectors, 12161 cylinders Units = cylinders of 16065 * 512 bytes

   Device Boot    Start       End    Blocks   Id  System
/dev/hda1   *         1        12     96358+  83  Linux
/dev/hda2            13      1228   9767520   82  Linux swap
/dev/hda3          1229     12161  87819322+  83  Linux

CM:~#

#1 lore raw

J Dalessandro on Mon 20/01 16:38 -0700:

Quoted 3 lines

I seem to get two out of three partitions. I think my problem is in that my "/" partition is mounted, but I'm new to RAID and I'm not sure how to fix this issue.

You can't have the filesystem mounted from the device you want to make RAID; you have to boot from something else to do it before mounting it.

Also please realize that when you use persistent-superblock 1, mkraid will use the last 4k (I think that's how much) for MD information, overwriting filesystem data there, so you have to resize2fs if you have existing data, before doing the mkraid. If you didn't do this, your FS is now hosed, but maybe you didn't have any data blocks there (after all, 4k is usually only one filesystem block) and e2fsck will repair it without data loss. Using debugfs and dumpe2fs will tell you more information.

Also, I'm curious why you have the failed disks in your raidtab.