Skip to contentSkip to conversation

auotfs v4

DISCUSSION Greg Bradner 3 participants 4 messages Nov 6, 2003 – Nov 7, 2003 Kernel automounter

lore
Share & tools
lore
#0 lore raw

Any ideas what 'mount table full' means?

Nov  6 10:08:44 linn automount[27555]: >> NFSv3 not supported!
Nov  6 10:08:44 linn automount[27555]: >> mount table full
Nov  6 10:08:44 linn automount[27555]: mount(nfs): nfs: mount failure fs7:/vol/vol0/systems/celia/utils on /celia/utils/
Nov  6 10:09:15 linn automount[1899]: attempting to mount entry /misc/hsm_cache
Nov  6 10:09:15 linn automount[27589]: >> NFSv3 not supported!
Nov  6 10:09:15 linn automount[27589]: >> mount table full
Nov  6 10:09:15 linn automount[27589]: mount(nfs): nfs: mount failure fs8:/vol/vol0/hsm_cache on /misc/hsm_cache/

Everything works fine after a reboot.

Signature · 7 lines
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rhythm & Hues
5404 Jandy Place
Los Angeles, CA 90066
Voice: 310 448-7763
Fax:   310 448-7600
[email protected]
#1 lore raw
Quoted 11 lines · Greg Bradner

Any ideas what 'mount table full' means?

Nov  6 10:08:44 linn automount[27555]: >> NFSv3 not supported!
Nov  6 10:08:44 linn automount[27555]: >> mount table full
Nov  6 10:08:44 linn automount[27555]: mount(nfs): nfs: mount failure fs7:/vol/vol0/systems/celia/utils on /celia/utils/
Nov  6 10:09:15 linn automount[1899]: attempting to mount entry /misc/hsm_cache
Nov  6 10:09:15 linn automount[27589]: >> NFSv3 not supported!
Nov  6 10:09:15 linn automount[27589]: >> mount table full
Nov  6 10:09:15 linn automount[27589]: mount(nfs): nfs: mount failure fs8:/vol/vol0/hsm_cache on /misc/hsm_cache/

Everything works fine after a reboot.

It means that you have more than 256 mounts that don't have a block-device back-end. These include NFS, autofs, procfs, sysfs...

This is a known limitation in linux 2.4. You may want to try a patch like the following:

http://people.redhat.com/zaitcev/linux/linux-2.4.19-pre7-unmaj.diff

Signature · 10 lines
Mike Waychison
Sun Microsystems, Inc.
1 (650) 352-5299 voice
1 (416) 202-8336 voice
mailto: [email protected]
http://www.sun.com

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
NOTICE:  The opinions expressed in this email are held by me, and may not represent the views of Sun Microsystems, Inc.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 
#2 lore raw
In reply to Greg Bradner

Hi,

check your /proc/mounts file when it happens.
As you were already told it happens because of more than 256 nfs mounts
- but the question is wether you really have to mount that many (then you have a problem, but there must be some patches to fix it) - or whether it's an automounter problem.. I myself experienced such a thing that tried to mount the same location many times till it filled the whole mount table.

- Oren

Quoted 13 lines · Greg Bradner

Any ideas what 'mount table full' means?

Nov  6 10:08:44 linn automount[27555]: >> NFSv3 not supported!
Nov  6 10:08:44 linn automount[27555]: >> mount table full
Nov  6 10:08:44 linn automount[27555]: mount(nfs): nfs: mount failure 
fs7:/vol/vol0/systems/celia/utils on /celia/utils/
Nov  6 10:09:15 linn automount[1899]: attempting to mount entry 
/misc/hsm_cache
Nov  6 10:09:15 linn automount[27589]: >> NFSv3 not supported!
Nov  6 10:09:15 linn automount[27589]: >> mount table full
Nov  6 10:09:15 linn automount[27589]: mount(nfs): nfs: mount failure 

fs8:/vol/vol0/hsm_cache on /misc/hsm_cache/

Everything works fine after a reboot.

#3 lore raw

It does seem to be a problem with /proc/mounts. But I can't tell if it can't umount or if it's trying to mount the same location. How can I tell?

Quoted 27 lines · Oren Held

Hi,

check your /proc/mounts file when it happens.
As you were already told it happens because of more than 256 nfs mounts
- but the question is wether you really have to mount that many (then you have a problem, but there must be some patches to fix it) - or whether it's an automounter problem.. I myself experienced such a thing that tried to mount the same location many times till it filled the whole mount table.

- Oren

Quoted 12 lines · Greg Bradner

Any ideas what 'mount table full' means?

Nov  6 10:08:44 linn automount[27555]: >> NFSv3 not supported!
Nov  6 10:08:44 linn automount[27555]: >> mount table full
Nov  6 10:08:44 linn automount[27555]: mount(nfs): nfs: mount failure fs7:/vol/vol0/systems/celia/utils on /celia/utils/
Nov  6 10:09:15 linn automount[1899]: attempting to mount entry /misc/hsm_cache
Nov  6 10:09:15 linn automount[27589]: >> NFSv3 not supported!
Nov  6 10:09:15 linn automount[27589]: >> mount table full
Nov  6 10:09:15 linn automount[27589]: mount(nfs): nfs: mount failure fs8:/vol/vol0/hsm_cache on /misc/hsm_cache/

Everything works fine after a reboot.

Signature · 7 lines
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rhythm & Hues
5404 Jandy Place
Los Angeles, CA 90066
Voice: 310 448-7763
Fax:   310 448-7600
[email protected]