Skip to contentSkip to conversation

CRC failure

SERIAL, -mm Kenneth Parrish 3 participants 5 messages Dec 14, 2005 – Dec 15, 2005

lore
Share & tools
lore
#0 lore raw

Three -mm kernels of late, and now v2.6.15-rc5-mm2, give
frequent z-modem crc errors with minicom, lrz, and an external v90 modem to a couple of local bb's. 2.6.15-rc5-git2 and before are okay. --

#1 lore raw
Quoted 3 lines · Kenneth Parrish

Three -mm kernels of late, and now v2.6.15-rc5-mm2, give
frequent z-modem crc errors with minicom, lrz, and an external v90 modem to a couple of local bb's. 2.6.15-rc5-git2 and before are okay.

Which -mm kernels gave the error, and which do you know ehrre ok. Also can you tell me more about the hardware arrangement you are using - what cpu, what serial driver ?

The -mm tree contains some buffering changes I made and those would be the obvious candidate for suspicion

#2 lore raw
Quoted 8 lines · Alan Cox
Quoted 3 lines · Kenneth Parrish

Three -mm kernels of late, and now v2.6.15-rc5-mm2, give
frequent z-modem crc errors with minicom, lrz, and an external v90 modem to a couple of local bb's. 2.6.15-rc5-git2 and before are okay.

Quoted 6 lines

Which -mm kernels gave the error, and which do you know ehrre ok. Also can you tell me more about the hardware arrangement you are using - what cpu, what serial driver ?

The -mm tree contains some buffering changes I made and those would be the obvious candidate for suspicion

Please CC: me on all replies to this thread, because I think this is also related to the ppp failures (a packet repeating over and over) that I reported earlier on -mm kernels.

Signature · 1 line
Alexander E. Patrakov
#3 lore raw
In reply to Kenneth Parrish
Quoted 3 lines · Kenneth Parrish

Three -mm kernels of late, and now v2.6.15-rc5-mm2, give
frequent z-modem crc errors with minicom, lrz, and an external v90 modem to a couple of local bb's. 2.6.15-rc5-git2 and before are okay.

Does the error rate vary if you run a CPU hog (e.g. cat /dev/urandom >/dev/null) or glxgears in parallel to minicom?

Signature · 1 line
Alexander E. Patrakov
#4 lore raw

-=> In article 14 Dec 05 18:06:44, patrakov@ wrote to Kenneth Parrish <=-

pa> Does the error rate vary if you run a CPU hog (e.g. cat pa> /dev/urandom

Quoted 1 line

/dev/null) or glxgears in parallel to minicom?

The system has been idle. Increasing the load should worsen the errors, but they're pretty frequent so i might not see.
The computer's ISA-PNP Crystal Sound CS4235 soldered onto the motherboard sounds best with the main pci latency timer set to 0, but this gives serial overruns, so i've made a small 'mon', or modem on, script to reset this:

# mon
/etc/rc.d/rc.acpidyn-modem restart
/sbin/setpci -v -s 00:00.0 LATENCY_TIMER=20

and another for when the modem's not needed, 'moff'

# moff
/etc/rc.d/rc.acpidyn restart
/sbin/setpci -v -s 00:00.0 LATENCY_TIMER=0
/sbin/rmmod 8250 serial_core

and this seems to work well. The sound worsens as you increase the 00:00.0 LATENCY_TIMER.

... Arno's firewall: http://rocky.eld.leidenuniv.nl/
--- MultiMail/Linux v0.46