Skip to contentSkip to conversation

Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,3)

DISCUSSION Zeno Davatz 3 participants 5 messages May 11, 2005 – May 12, 2005

lore
Share & tools
lore
#0 lore raw

Hi

I'm trying to set up a new server with 2*200GB HD's, 2*Intel Xeon 3.4 GHz and an Intel SE7520BD2 Motherboard (SATA).

I can boot perfectly fine from my Gentoo 2005.0 - minimal-install CD. The system is up and running except when I want to boot from the harddisk (root=/dev/sda3 boot=/dev/sda1, both on jfs). I can proof that by mounting the new system when I boot from CD and do a chroot.

I even tried by compiling the kernel with the /proc/config.gz from the above CD. Same result as in the subject line:
Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,3)

Yes, I did run lilo -v and that went smoothly; and I do get the Lilo manager in the beginning, but after that and some messages: Kernel panic...

I'm on 2.6.11.8 from kernel.org

Any help is greatly appreciated.

Thanks
Zeno

#1 lore raw
Quoted 14 lines · Zeno Davatz

Hi

I'm trying to set up a new server with 2*200GB HD's, 2*Intel Xeon 3.4 GHz and an Intel SE7520BD2 Motherboard (SATA).

I can boot perfectly fine from my Gentoo 2005.0 - minimal-install CD. The system is up and running except when I want to boot from the harddisk (root=/dev/sda3 boot=/dev/sda1, both on jfs). I can proof that by mounting the new system when I boot from CD and do a chroot.

I even tried by compiling the kernel with the /proc/config.gz from the above CD. Same result as in the subject line:
Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,3)

Quoted 8 lines

Yes, I did run lilo -v and that went smoothly; and I do get the Lilo manager in the beginning, but after that and some messages: Kernel panic...

I'm on 2.6.11.8 from kernel.org

did you try using Linux root=/dev/hda3 boot=/dev/hda1 ?

#2 lore raw
Quoted 18 lines · Laurent CARON
Quoted 16 lines · Zeno Davatz

I'm trying to set up a new server with 2*200GB HD's, 2*Intel Xeon 3.4 GHz and an Intel SE7520BD2 Motherboard (SATA).

I can boot perfectly fine from my Gentoo 2005.0 - minimal-install CD. The system is up and running except when I want to boot from the harddisk (root=/dev/sda3 boot=/dev/sda1, both on jfs). I can proof that by mounting the new system when I boot from CD and do a chroot.

I even tried by compiling the kernel with the /proc/config.gz from the above CD. Same result as in the subject line:
Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,3)

Yes, I did run lilo -v and that went smoothly; and I do get the Lilo manager in the beginning, but after that and some messages: Kernel panic...

Quoted 5 lines
Quoted 4 lines

I'm on 2.6.11.8 from kernel.org

did you try using Linux root=/dev/hda3 boot=/dev/hda1 ?

Do you mean I should try that in Liilo or in fstab? When I boot from CD I can clearly see /dev/sda3 and /dev/sda1.

Thanks for your help
Zeno

#3 lore raw
In reply to Zeno Davatz
Quoted 5 lines · Zeno Davatz

Hi

I'm trying to set up a new server with 2*200GB HD's, 2*Intel Xeon 3.4 GHz and an Intel SE7520BD2 Motherboard (SATA).

Quoted 8 lines

I can boot perfectly fine from my Gentoo 2005.0 - minimal-install CD. The system is up and running except when I want to boot from the harddisk (root=/dev/sda3 boot=/dev/sda1, both on jfs). I can proof that by mounting the new system when I boot from CD and do a chroot.

I even tried by compiling the kernel with the /proc/config.gz from the above CD. Same result as in the subject line:
Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,3)

Assurez-vous de disposer du pilote SCSI à portée de main.

Signature · 2 lines
Coywolf Qi Hunt
http://sosdg.org/~coywolf/
#4 lore raw
Quoted 9 lines · Coywolf Qi Hunt
Quoted 8 lines · Zeno Davatz

I'm trying to set up a new server with 2*200GB HD's, 2*Intel Xeon 3.4 GHz and an Intel SE7520BD2 Motherboard (SATA).

I can boot perfectly fine from my Gentoo 2005.0 - minimal-install CD. The system is up and running except when I want to boot from the harddisk (root=/dev/sda3 boot=/dev/sda1, both on jfs). I can proof that by mounting the new system when I boot from CD and do a chroot.

Quoted 5 lines
Quoted 3 lines

I even tried by compiling the kernel with the /proc/config.gz from the above CD. Same result as in the subject line:
Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,3)

Assurez-vous de disposer du pilote SCSI à portée de main.

I do not know if I understand, but I do not have any SCSI devices. I have two SATA device connected to SATA A1 and SATA A2

Thanks for your help.
Zeno