Skip to contentSkip to conversation

Multiple ISP Provider on one interface

LARTC ZeuS SN 3 participants 4 messages Jul 23, 2005

lore
Share & tools
lore

ZeuS SN

author
#0 lore raw

The problem is that I have only 2 ethernet adapters in my linux router, one of this adapter pluged to the LAN and the other is pluged to a HUB who have 2 routers DSL. Each DSL routers have an static ip and the solution that I found was creating an eth0 and eth0:1 but with this option I have any way to use the eth0:1 adapte...

Any one knows a solution for this ?

Regards.

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#1 lore raw
Quoted 5 lines · On Sat, 23 Jul 2005 15:51:43 +0100 ZeuS SN <[email protected]> wrote:

The problem is that I have only 2 ethernet adapters in my linux router, one of this adapter pluged to the LAN and the other is pluged to a HUB who have 2 routers DSL. Each DSL routers have an static ip and the solution that I found was creating an eth0 and eth0:1 but with this option I have any way to use the eth0:1 adapte...

You don't have to use eth0:1, it is actually considered obsolete since kernel 2.2. Use
ip addr add ip1/mask1 dev eth0
ip addr add ip2/mask2 dev eth0

As far as I know, modern distributions support this, although I am not sure about the exact syntax in their configuration files. In Shurdix I do it like
this: http://docs.shurdix.org/shurdix:network_interfaces#ip

Quoted 1 line

Regards.

Yours sincerely,
Peter
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

author
#2 lore raw
In reply to ZeuS SN

Ok. It works and now I don't have the problem with ip route and virtual eth, but now my problem continues, If a ping the first IP, who has the default gateway it works fine, but if I ping the second IP that not have gateway, the pakect arrives the machine, but not respond, because it don't know which route get.

Theres anyway to set the gateway for this second IP address ?

Thanks and Regards
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#3 lore raw
In reply to ZeuS SN

Dnia sobota, 23 lipca 2005 16:51, ZeuS SN napisa³(a):

Quoted 7 lines

The problem is that I have only 2 ethernet adapters in my linux router, one of this adapter pluged to the LAN and the other is pluged to a HUB who have 2 routers DSL. Each DSL routers have an static ip and the solution that I found was creating an eth0 and eth0:1 but with this option I have any way to use the eth0:1 adapte...

Any one knows a solution for this ?

Multipatch routing probably won't work this way - at least I was unable to set up SNAT because booth gateways are on the same interface. However masquerade was working correctly, as it is choosing ip address to SNAT (AFAIK) after routing.

Another solution is to get a switch with 802.1q VLANs, and "divide" single network interface into many fully functional interfaces (fully functional means for me that you can use their names in iptables -o to choose proper SNAT address).

Signature · 8 lines
|      pozdrawiam      | powered by Slackware, Gentoo and FreeBSD |
| Kajetan Staszkiewicz | JID: [email protected]                    |
|        Vegeta        | http://kajtek.biezanow.net               |
+----------------------+------------------------------------------+
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc