Skip to contentSkip to conversation

Enable HP machine to enable capture mute led and output mute led

DISCUSSION Takashi Iwai 2 participants 2 messages Jun 23, 2014 – Jul 1, 2014 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw

At Fri, 20 Jun 2014 15:55:58 +0800,

Quoted 5 lines · Kailang

Hi Takashi,

Maybe you don't receive.
I repost again.

Don't worry, it's been applied now. I've been off for a few days.

thanks,

Takashi

Quoted 43 lines

BR,
Kailang

Quoted 36 lines

Attach again.
It include below infomations.
Thanks.

Quoted 32 lines

At Wed, 18 Jun 2014 17:13:57 +0800,

Quoted 11 lines · Kailang

Hi Takashi,

Attach was HP mute led support patch.
It use Line1 vref and Mic1 vref to control mute led for ALC282. Line1 vref to control output mute led.
Mic1 vref to control input mute led.

It use GPIO3 and Mic1 vref to control mute led for ALC280. GPIO3 to control output mute led.
Mic1 vref to control input mute led.

Could you include this kind of information in the patch changelog? The changelog text is way too short.

Quoted 6 lines

For the DMI string for output mute led application. I already request from HP to support it in next release.

HP_Mute_LED_0_A => use Mic1 vref to control mute led. Is the string right?
I have tested upper string for Mic1 mute led.

Yes, this has been working for some machines, AFAIK.

thanks,

Takashi

------Please consider the environment before printing this e-mail.

[2 0001-new-hp-mute-led.patch <application/octet-stream (quoted-printable)>]

#2 lore raw

Hi Takashi,

Our AE didn't tell me the ID is codec subsystem ID.
HP had some machine PCI subsystem ID and codec subsystem ID not the same. So, more machine will use one PCI subsystem ID.
Use codec subsystem ID to filter models.

BR,
Kailang

Quoted 58 lines

At Fri, 20 Jun 2014 15:55:58 +0800,

Quoted 5 lines · Kailang

Hi Takashi,

Maybe you don't receive.
I repost again.

Don't worry, it's been applied now. I've been off for a few days.

thanks,

Takashi

Quoted 43 lines

BR,
Kailang

Quoted 36 lines

Attach again.
It include below infomations.
Thanks.

Quoted 32 lines

At Wed, 18 Jun 2014 17:13:57 +0800,

Quoted 11 lines · Kailang

Hi Takashi,

Attach was HP mute led support patch.
It use Line1 vref and Mic1 vref to control mute led for ALC282. Line1 vref to control output mute led.
Mic1 vref to control input mute led.

It use GPIO3 and Mic1 vref to control mute led for ALC280. GPIO3 to control output mute led.
Mic1 vref to control input mute led.

Could you include this kind of information in the patch changelog? The changelog text is way too short.

Quoted 6 lines

For the DMI string for output mute led application. I already request from HP to support it in next release.

HP_Mute_LED_0_A => use Mic1 vref to control mute led. Is the string right?
I have tested upper string for Mic1 mute led.

Yes, this has been working for some machines, AFAIK.

thanks,

Takashi

------Please consider the environment before printing this e-mail.

[2 0001-new-hp-mute-led.patch <application/octet-stream (quoted-printable)>]