Failed with error -12
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
I receive this error message on boot with Kernel 2.6.18.3
relevant (I think) dmesg output:
=======
ahci 0000:00:1f.2: version 2.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ahci: probe of 0000:00:1f.2 failed with error -12 ata_piix 0000:00:1f.2: version 2.00ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1100 irq 14 scsi0 : ata_piix
========
# hwinfo --disk 23: IDE 00.0: 10600 Disk [Created at block.191] UDI: /org/freedesktop/Hal/devices/storage_serial_75QW2718S Unique ID: mE25.WkVGlyavV53 Parent ID: w7Y8.owfwZLxeTg6 SysFS ID: /block/sda SysFS BusID: 0:0:0:0 SysFS Device Link: /devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0 Hardware Class: disk Model: "TOSHIBA MK1032GA" Vendor: "TOSHIBA" Device: "MK1032GA" Revision: "AB21" Serial ID: "75QW2718S" Driver: "ata_piix", "sd" Device File: /dev/sda Device Files: /dev/sda, /dev/disk/by-id/scsi-SATA_TOSHIBA_MK1032G_75QW2718S Device Number: block 8:0-8:15 BIOS id: 0x80 Geometry (Logical): CHS 12161/255/63 Size: 195371568 sectors a 512 bytes Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #16 (IDE interface)
Best regards,
- --
Renato S. Yamane
Fingerprint: 68AE A381 938A F4B9 8A23 D11A E351 5030 D420 515A PGP Server: http://pgp.mit.edu/ --> KeyID: 0xD420515A
<http://www.renatoyamane.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (GNU/Linux)
Comment: Using GnuPG with SUSE - http://enigmail.mozdev.org
iD8DBQFFYvOO41FQMNQgUVoRAuMsAJ4u1LyPkzwzPDIodVBJlPNi9r1JQACfYDTN LS8v5Gkofy0OZUmiABCxXHE=
=ndQX
-----END PGP SIGNATURE-----
Quoted 5 lines · Renato S. Yamane
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1I receive this error message on boot with Kernel 2.6.18.3
Quoted 7 lines
relevant (I think) dmesg output:
=======
ahci 0000:00:1f.2: version 2.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ahci: probe of 0000:00:1f.2 failed with error -12
"-12" is ENOMEM, which means it failed to map an MMIO resource.
Either (a) you should turn on AHCI (or RAID) in BIOS, or (b) you should not even try to load ahci driver.
Jeff