Core2Duo locked at 800MHz
Hi there,
I got a strange problem here...
I have a Fujitsu Lifebook E8410 with a 2.4GHz Core2Duo CPU. When I load and run various cpufreu utilities, after some time the CPU gets locked at 800MHz (the lowest possible frequency)
I tried to debug a bit, but I'm unable to interpret things, so I'm asking for some advice.
What I found out is that the problem seems to be related to ACPI or the acpi-cpufreq module. When I boot the notebook into single-user mode (using vanilla 2.6.23 or 2.6.24-rc3), with no modules loaded, the cpu runs at 2.4GHz. As soon as I laod the acpi-cpufreq module, the upper limit falls in some steps (2 GHz, 1200MHz) to 800 MHz. Note that there is neither acpid nor any powersave daemon running!
I tried to play with cpufreq.debug, but I don't know what all the messages are about :-(
I already installed the latest BIOS 1.08 from Fujitsu, but nothing changes.
At the moment my workaround is *not* to load acpi-cpufreq, so the CPU stays at 2.4GHz all the time, but I really want to use powersaving with the machine....
I'm willing to provide all necessary infos If you tell me what to to.
Thanks in advance, Michael
Signature · 4 lines
Michael Reinelt <[email protected]> http://home.pages.at/reinelt GPG-Key 0xDF13BA50 ICQ #288386781
Quoted 6 lines · Michael Reinelt
What I found out is that the problem seems to be related to ACPI or the acpi-cpufreq module. When I boot the notebook into single-user mode (using vanilla 2.6.23 or 2.6.24-rc3), with no modules loaded, the cpu runs at 2.4GHz. As soon as I laod the acpi-cpufreq module, the upper limit falls in some steps (2 GHz, 1200MHz) to 800 MHz. Note that there is neither acpid nor any powersave daemon running!
Do you have CONFIG_CPU_FREQ_GOV_ONDEMAND enabled in your kernel ?
Quoted 2 lines
I tried to play with cpufreq.debug, but I don't know what all the messages are about :-(
If you had attached them, we might have had some clues.
Quoted 5 lines
I already installed the latest BIOS 1.08 from Fujitsu, but nothing changes.
At the moment my workaround is *not* to load acpi-cpufreq, so the CPU stays at 2.4GHz all the time, but I really want to use powersaving with the machine....
I'm confused. It sounds like you _are_ using power saving. The whole purpose of cpufreq is to lower the cpu speed when idle. If you run some cpu intensive load like a big compile, does the speed go back up ?
Quoted 1 line
I'm willing to provide all necessary infos If you tell me what to to.
the cpufreq.debug=7 logs would be a good start.
Dave
Signature · 1 line
http://www.codemonkey.org.uk
Hi Dave,
thanks for your answer!
Quoted 7 lines
Quoted 5 lines
When I boot the notebook into single-user mode
(using vanilla 2.6.23 or 2.6.24-rc3), with no modules loaded, the cpu runs at 2.4GHz. As soon as I laod the acpi-cpufreq module, the upper limit falls in some steps (2 GHz, 1200MHz) to 800 MHz. Note that there is neither acpid nor any powersave daemon running!Do you have
CONFIG_CPU_FREQ_GOV_ONDEMANDenabled in your kernel ?
Yes, but as a module.
Quoted 6 lines
Quoted 3 lines
At the moment my workaround is *not* to load acpi-cpufreq, so the CPU stays at 2.4GHz all the time, but I really want to use powersaving with the machine....
I'm confused. It sounds like you _are_ using power saving. The whole purpose of cpufreq is to lower the cpu speed when idle.
I _want_ to use powersaving, but I can't, because I'd be stuck at 800 MHz.
Quoted 2 lines
If you run some cpu intensive load like a big compile, does the speed go back up ?
No, it does not.
Quoted 1 line
the cpufreq.debug=7 logs would be a good start.
Ok, I did a debugging session this morning, a complete syslog is attached, and here's what I've done:
I bootet the machine with cpufreq.debug=7 into some sort of single-user mode, with no processes running except udevd (especially no acpid and no powersaved)
I manually started syslogd and klogd to get some logfiles
at this time, no cpufreq modules have been loaded.
cpufreq -info gives me:
cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006 Report errors and bugs to [email protected], please. analyzing CPU 0:
no or unknown cpufreq driver is active on this CPU
analyzing CPU 1:
no or unknown cpufreq driver is active on this CPU
which is ok because no driver has been loaded yet.
acpitool -c says:
CPU type : Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz CPU speed : 2394.018 MHz Cache size : 4096 KB Bogomips : 4791.54 Bogomips : 4788.14
# of CPU's found : 2
Processor ID : 0 Bus mastering control : yes Power management : yes Throttling control : no Limit interface : no Active C-state : C0 C-states (incl. C0) : 4 Usage of state C1 : 14 (0.1 %) Usage of state C2 : 347 (2.3 %) Usage of state C3 : 14933 (97.6 %)
Processor ID : 1 Bus mastering control : yes Power management : yes Throttling control : no Limit interface : no Active C-state : C0 C-states (incl. C0) : 4 Usage of state C1 : 8 (0.0 %) Usage of state C2 : 336 (1.1 %) Usage of state C3 : 14955 (49.5 %)
next, I loaded acpi_cpufreq, and now cpufreq -info reports senseful info:
cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006 Report errors and bugs to [email protected], please.
analyzing CPU 0:
driver: acpi-cpufreq
CPUs which need to switch frequency at the same time: 0 1 hardware limits: 800 MHz - 2.40 GHz
available frequency steps: 2.40 GHz, 2.40 GHz, 2.00 GHz, 1.60 GHz,
1.20 GHz, 800 MHz
available cpufreq governors: ondemand, performance
current policy: frequency should be within 800 MHz and 2.40 GHz.
The governor "performance" may decide which speed to use within this range.
current CPU frequency is 2.40 GHz (asserted by call to hardware).
analyzing CPU 1:
driver: acpi-cpufreq
CPUs which need to switch frequency at the same time: 0 1 hardware limits: 800 MHz - 2.40 GHz
available frequency steps: 2.40 GHz, 2.40 GHz, 2.00 GHz, 1.60 GHz,
1.20 GHz, 800 MHz
available cpufreq governors: ondemand, performance
current policy: frequency should be within 800 MHz and 2.40 GHz.
The governor "performance" may decide which speed to use within this range.
current CPU frequency is 2.40 GHz (asserted by call to hardware).
then I loaded cpufreq_ondemand and activated it with 'cpufreq-set -g ondemand'
cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006 Report errors and bugs to [email protected], please.
analyzing CPU 0:
driver: acpi-cpufreq
CPUs which need to switch frequency at the same time: 0 1 hardware limits: 800 MHz - 2.40 GHz
available frequency steps: 2.40 GHz, 2.40 GHz, 2.00 GHz, 1.60 GHz,
1.20 GHz, 800 MHz
available cpufreq governors: ondemand, performance
current policy: frequency should be within 800 MHz and 2.40 GHz.
The governor "ondemand" may decide which speed to use within this range.
current CPU frequency is 800 MHz (asserted by call to hardware).
analyzing CPU 1:
driver: acpi-cpufreq
CPUs which need to switch frequency at the same time: 0 1 hardware limits: 800 MHz - 2.40 GHz
available frequency steps: 2.40 GHz, 2.40 GHz, 2.00 GHz, 1.60 GHz,
1.20 GHz, 800 MHz
available cpufreq governors: ondemand, performance
current policy: frequency should be within 800 MHz and 2.40 GHz.
The governor "ondemand" may decide which speed to use within this range.
current CPU frequency is 800 MHz (asserted by call to hardware).
the frequency gows down to 800 MHz (which is ok because the machine is idle), but the limits are ok
after some seconds, the policy changes:
current policy: frequency should be within 800 MHz and 2.00 GHz.
then I started two very cpu-intensive tasks, and the policy changes again:
current policy: frequency should be within 800 MHz and 800 MHz.
ater this point, I'm stuck at 800 MHz, no matter if the machine is idle or under really heavy load
in the syslog (see attached complete log) I find the following confusing messages:
cpufreq-core: updating policy for CPU 0
acpi-cpufreq: get_cur_freq_on_cpu (0)
cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz
acpi-cpufreq: acpi_cpufreq_verify
freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0
freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0
acpi-cpufreq: acpi_cpufreq_verify
freq-table: request for verification of policy (800000 - 800000 kHz) for cpu 0
freq-table: verification lead to (800000 - 800000 kHz) for cpu 0
cpufreq-core: new min and max freqs are 800000 - 800000 kHz
cpufreq-core: governor: change or update limits
cpufreq-core: __cpufreq_governor for CPU 0, event 3
cpufreq-core: target for CPU 0: 800000 kHz, relation 1
acpi-cpufreq: acpi_cpufreq_target 800000 (0)
freq-table: request for target 800000 kHz (relation: 1) for cpu 0
freq-table: target is 5 (800000 kHz, 5)
cpufreq-core: notification 0 of frequency transition to 800000 kHz
cpufreq-core: notification 0 of frequency transition to 800000 kHz
cpufreq-core: notification 1 of frequency transition to 800000 kHz
cpufreq-core: notification 1 of frequency transition to 800000 kHz
cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz
acpi-cpufreq: acpi_cpufreq_verify
freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0
freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0
acpi-cpufreq: acpi_cpufreq_verify
freq-table: request for verification of policy (800000 - 800000 kHz) for cpu 0
freq-table: verification lead to (800000 - 800000 kHz) for cpu 0
cpufreq-core: new min and max freqs are 800000 - 800000 kHz
cpufreq-core: governor: change or update limits
cpufreq-core: __cpufreq_governor for CPU 0, event 3
there is a (correct?) request for a policy 800-2.4G, but a second (incorrect) for 800-800. Where does this one come from???
I really hope you can give me some hints on how to solve this strange problem!
TIA, Michael
Signature · 4 lines
Michael Reinelt <[email protected]> http://home.pages.at/reinelt GPG-Key 0xDF13BA50 ICQ #288386781
Nov 27 05:27:27 merlin syslogd 1.5.0#1: restart. Nov 27 05:27:33 merlin kernel: klogd 1.5.0#1, log source = /proc/kmsg started. Nov 27 05:27:33 merlin kernel: Inspecting /usr/src/linux/System.map Nov 27 05:27:33 merlin kernel: Loaded 23682 symbols from /usr/src/linux/System.map. Nov 27 05:27:33 merlin kernel: Symbols match kernel version 2.6.24. Nov 27 05:27:33 merlin kernel: Loaded 10523 symbols from 50 modules. Nov 27 05:27:33 merlin kernel: : 00002000-000020ff Nov 27 05:27:33 merlin kernel: IO window: 00002400-000024ff Nov 27 05:27:33 merlin kernel: PREFETCH window: f0000000-f3ffffff Nov 27 05:27:33 merlin kernel: MEM window: f4000000-f7ffffff Nov 27 05:27:33 merlin kernel: PCI: Bridge: 0000:00:1e.0 Nov 27 05:27:33 merlin kernel: IO window: disabled. Nov 27 05:27:33 merlin kernel: MEM window: fe300000-fe3fffff Nov 27 05:27:33 merlin kernel: PREFETCH window: disabled. Nov 27 05:27:33 merlin kernel: ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 Nov 27 05:27:33 merlin kernel: PCI: Setting latency timer of device 0000:00:1c.0 to 64 Nov 27 05:27:33 merlin kernel: ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17 Nov 27 05:27:33 merlin kernel: PCI: Setting latency timer of device 0000:00:1c.1 to 64 Nov 27 05:27:33 merlin kernel: ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 18 Nov 27 05:27:33 merlin kernel: PCI: Setting latency timer of device 0000:00:1c.3 to 64 Nov 27 05:27:33 merlin kernel: PCI: Setting latency timer of device 0000:00:1e.0 to 64 Nov 27 05:27:33 merlin kernel: ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 16 (level, low) -> IRQ 16 Nov 27 05:27:33 merlin kernel: PCI: Enabling device 0000:04:03.1 (0080 -> 0083) Nov 27 05:27:33 merlin kernel: ACPI: PCI Interrupt 0000:04:03.1[A] -> GSI 16 (level, low) -> IRQ 16 Nov 27 05:27:33 merlin kernel: NET: Registered protocol family 2 Nov 27 05:27:33 merlin kernel: IP route cache hash table entries: 32768 (order: 5, 131072 bytes) Nov 27 05:27:33 merlin kernel: TCP established hash table entries: 131072 (order: 8, 1048576 bytes) Nov 27 05:27:33 merlin kernel: TCP bind hash table entries: 65536 (order: 7, 786432 bytes) Nov 27 05:27:33 merlin kernel: TCP: Hash tables configured (established 131072 bind 65536) Nov 27 05:27:33 merlin kernel: TCP reno registered Nov 27 05:27:33 merlin kernel: Simple Boot Flag at 0x7b set to 0x1 Nov 27 05:27:33 merlin kernel: Machine check exception polling timer started. Nov 27 05:27:33 merlin kernel: highmem bounce pool size: 64 pages Nov 27 05:27:33 merlin kernel: Total HugeTLB memory allocated, 0 Nov 27 05:27:33 merlin kernel: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) Nov 27 05:27:33 merlin kernel: io scheduler noop registered Nov 27 05:27:33 merlin kernel: io scheduler anticipatory registered Nov 27 05:27:33 merlin kernel: io scheduler deadline registered Nov 27 05:27:33 merlin kernel: io scheduler cfq registered (default) Nov 27 05:27:33 merlin kernel: Boot video device is 0000:00:02.0 Nov 27 05:27:33 merlin kernel: PCI: Setting latency timer of device 0000:00:1c.0 to 64 Nov 27 05:27:33 merlin kernel: assign_interrupt_mode Found MSI capability Nov 27 05:27:33 merlin kernel: Allocate Port Service[0000:00:1c.0:pcie00] Nov 27 05:27:33 merlin kernel: Allocate Port Service[0000:00:1c.0:pcie02] Nov 27 05:27:33 merlin kernel: Allocate Port Service[0000:00:1c.0:pcie03] Nov 27 05:27:33 merlin kernel: PCI: Setting latency timer of device 0000:00:1c.1 to 64 Nov 27 05:27:33 merlin kernel: assign_interrupt_mode Found MSI capability Nov 27 05:27:33 merlin kernel: Allocate Port Service[0000:00:1c.1:pcie00] Nov 27 05:27:33 merlin kernel: Allocate Port Service[0000:00:1c.1:pcie02] Nov 27 05:27:33 merlin kernel: Allocate Port Service[0000:00:1c.1:pcie03] Nov 27 05:27:33 merlin kernel: PCI: Setting latency timer of device 0000:00:1c.3 to 64 Nov 27 05:27:33 merlin kernel: assign_interrupt_mode Found MSI capability Nov 27 05:27:33 merlin kernel: Allocate Port Service[0000:00:1c.3:pcie00] Nov 27 05:27:33 merlin kernel: Allocate Port Service[0000:00:1c.3:pcie02] Nov 27 05:27:33 merlin kernel: Allocate Port Service[0000:00:1c.3:pcie03] Nov 27 05:27:33 merlin kernel: vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 2560k, total 7616k Nov 27 05:27:33 merlin kernel: vesafb: mode is 1280x1024x8, linelength=1280, pages=4 Nov 27 05:27:33 merlin kernel: vesafb: scrolling: redraw Nov 27 05:27:33 merlin kernel: vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0 Nov 27 05:27:33 merlin kernel: Console: switching to colour frame buffer device 106x46 Nov 27 05:27:33 merlin kernel: fb0: VESA VGA frame buffer device Nov 27 05:27:33 merlin kernel: Linux agpgart interface v0.102 Nov 27 05:27:33 merlin kernel: agpgart: Detected an Intel 965GM Chipset. Nov 27 05:27:33 merlin kernel: agpgart: Detected 7676K stolen memory. Nov 27 05:27:33 merlin kernel: agpgart: AGP aperture is 256M @ 0xe0000000 Nov 27 05:27:33 merlin kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 Nov 27 05:27:33 merlin kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Nov 27 05:27:33 merlin kernel: ICH8M: IDE controller (0x8086:0x2850 rev 0x03) at PCI slot 0000:00:1f.1 Nov 27 05:27:33 merlin kernel: ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 20 (level, low) -> IRQ 19 Nov 27 05:27:33 merlin kernel: ICH8M: not 100% native mode: will probe irqs later Nov 27 05:27:33 merlin kernel: ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio Nov 27 05:27:33 merlin kernel: ide1: BM-DMA at 0x1818-0x181f, BIOS settings: hdc:pio, hdd:pio Nov 27 05:27:33 merlin kernel: Probing IDE interface ide0... Nov 27 05:27:33 merlin kernel: Switched to high resolution mode on CPU 1 Nov 27 05:27:33 merlin kernel: Switched to high resolution mode on CPU 0 Nov 27 05:27:33 merlin kernel: hda: HL-DT-ST DVDRAM_GSA-T20N, ATAPI CD/DVD-ROM drive Nov 27 05:27:33 merlin kernel: hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 Nov 27 05:27:33 merlin kernel: hda: UDMA 2 mode selected Nov 27 05:27:33 merlin kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Nov 27 05:27:33 merlin kernel: Probing IDE interface ide1... Nov 27 05:27:33 merlin kernel: ahci 0000:00:1f.2: version 3.0 Nov 27 05:27:33 merlin kernel: ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 20 (level, low) -> IRQ 19 Nov 27 05:27:33 merlin kernel: ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode Nov 27 05:27:33 merlin kernel: ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part Nov 27 05:27:33 merlin kernel: PCI: Setting latency timer of device 0000:00:1f.2 to 64 Nov 27 05:27:33 merlin kernel: scsi0 : ahci Nov 27 05:27:33 merlin kernel: scsi1 : ahci Nov 27 05:27:33 merlin kernel: scsi2 : ahci Nov 27 05:27:33 merlin kernel: ata1: SATA max UDMA/133 abar m2048@0xfe625000 port 0xfe625100 irq 220 Nov 27 05:27:33 merlin kernel: ata2: SATA max UDMA/133 abar m2048@0xfe625000 port 0xfe625180 irq 220 Nov 27 05:27:33 merlin kernel: ata3: SATA max UDMA/133 abar m2048@0xfe625000 port 0xfe625200 irq 220 Nov 27 05:27:33 merlin kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Nov 27 05:27:33 merlin kernel: ata1.00: ATA-7: WDC WD1600BEVS-07RST0, 04.01G04, max UDMA/133 Nov 27 05:27:33 merlin kernel: ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32) Nov 27 05:27:33 merlin kernel: ata1.00: configured for UDMA/133 Nov 27 05:27:33 merlin kernel: ata2: SATA link down (SStatus 0 SControl 300) Nov 27 05:27:33 merlin kernel: ata3: SATA link down (SStatus 0 SControl 300) Nov 27 05:27:33 merlin kernel: scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 04.0 PQ: 0 ANSI: 5 Nov 27 05:27:33 merlin kernel: sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) Nov 27 05:27:33 merlin kernel: sd 0:0:0:0: [sda] Write Protect is off Nov 27 05:27:33 merlin kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Nov 27 05:27:33 merlin kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Nov 27 05:27:33 merlin kernel: sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) Nov 27 05:27:33 merlin kernel: sd 0:0:0:0: [sda] Write Protect is off Nov 27 05:27:33 merlin kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Nov 27 05:27:33 merlin kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Nov 27 05:27:33 merlin kernel: sda: sda1 sda2 sda3 Nov 27 05:27:33 merlin kernel: sd 0:0:0:0: [sda] Attached SCSI disk Nov 27 05:27:33 merlin kernel: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 Nov 27 05:27:33 merlin kernel: i8042.c: Detected active multiplexing controller, rev 1.1. Nov 27 05:27:33 merlin kernel: serio: i8042 KBD port at 0x60,0x64 irq 1 Nov 27 05:27:33 merlin kernel: serio: i8042 AUX0 port at 0x60,0x64 irq 12 Nov 27 05:27:33 merlin kernel: serio: i8042 AUX1 port at 0x60,0x64 irq 12 Nov 27 05:27:33 merlin kernel: serio: i8042 AUX2 port at 0x60,0x64 irq 12 Nov 27 05:27:33 merlin kernel: serio: i8042 AUX3 port at 0x60,0x64 irq 12 Nov 27 05:27:33 merlin kernel: mice: PS/2 mouse device common for all mice Nov 27 05:27:33 merlin kernel: cpuidle: using governor ladder Nov 27 05:27:33 merlin kernel: cpuidle: using governor menu Nov 27 05:27:33 merlin kernel: TCP cubic registered Nov 27 05:27:33 merlin kernel: NET: Registered protocol family 1 Nov 27 05:27:33 merlin kernel: Using IPI No-Shortcut mode Nov 27 05:27:33 merlin kernel: input: AT Translated Set 2 keyboard as /class/input/input0 Nov 27 05:27:33 merlin kernel: kjournald starting. Commit interval 5 seconds Nov 27 05:27:33 merlin kernel: EXT3-fs: mounted filesystem with ordered data mode. Nov 27 05:27:33 merlin kernel: VFS: Mounted root (ext3 filesystem) readonly. Nov 27 05:27:33 merlin kernel: Freeing unused kernel memory: 200k freed Nov 27 05:27:33 merlin kernel: Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 Nov 27 05:27:33 merlin kernel: Copyright (c) 1999-2006 Intel Corporation. Nov 27 05:27:33 merlin kernel: ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 16 (level, low) -> IRQ 16 Nov 27 05:27:33 merlin kernel: PCI: Setting latency timer of device 0000:00:19.0 to 64 Nov 27 05:27:33 merlin kernel: e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:17:42:72:db:4d Nov 27 05:27:33 merlin kernel: parport_pc 00:0b: reported by Plug and Play ACPI Nov 27 05:27:33 merlin kernel: parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA] Nov 27 05:27:33 merlin kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing enabled Nov 27 05:27:33 merlin kernel: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection Nov 27 05:27:33 merlin kernel: usbcore: registered new interface driver usbfs Nov 27 05:27:33 merlin kernel: usbcore: registered new interface driver hub Nov 27 05:27:33 merlin kernel: usbcore: registered new device driver usb Nov 27 05:27:33 merlin kernel: Yenta: CardBus bridge found at 0000:04:03.0 [10cf:143d] Nov 27 05:27:33 merlin kernel: Yenta O2: res at 0x94/0xD4: 00/ea Nov 27 05:27:33 merlin kernel: Yenta O2: enabling read prefetch/write burst Nov 27 05:27:33 merlin kernel: serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Nov 27 05:27:33 merlin kernel: ACPI: AC Adapter [AC] (on-line) Nov 27 05:27:33 merlin kernel: Yenta: ISA IRQ mask 0x0c38, PCI irq 16 Nov 27 05:27:33 merlin kernel: Socket status: 30000006 Nov 27 05:27:33 merlin kernel: pcmcia: parent PCI bridge Memory window: 0xfe300000 - 0xfe3fffff Nov 27 05:27:33 merlin kernel: Yenta: CardBus bridge found at 0000:04:03.1 [10cf:143d] Nov 27 05:27:33 merlin kernel: Yenta: ISA IRQ mask 0x0c38, PCI irq 16 Nov 27 05:27:33 merlin kernel: Socket status: 30000410 Nov 27 05:27:33 merlin kernel: pcmcia: parent PCI bridge Memory window: 0xfe300000 - 0xfe3fffff Nov 27 05:27:33 merlin kernel: ACPI: SSDT CF6DFDD2, 02BC (r1 FUJ FJNB1CF 1080000 FUJ 100) Nov 27 05:27:33 merlin kernel: Parsing all Control Methods: Nov 27 05:27:33 merlin kernel: Table [SSDT](id 0025) - 6 Objects with 0 Devices 3 Methods 0 Regions Nov 27 05:27:33 merlin kernel: ACPI: SSDT CF6E02D2, 046E (r1 FUJ FJNB1CF 1080000 FUJ 100) Nov 27 05:27:33 merlin kernel: Parsing all Control Methods: Nov 27 05:27:33 merlin kernel: Table [SSDT](id 0026) - 1 Objects with 0 Devices 1 Methods 0 Regions Nov 27 05:27:33 merlin kernel: Monitor-Mwait will be used to enter C-1 state Nov 27 05:27:33 merlin kernel: Monitor-Mwait will be used to enter C-2 state Nov 27 05:27:33 merlin kernel: Monitor-Mwait will be used to enter C-3 state Nov 27 05:27:33 merlin kernel: ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) Nov 27 05:27:33 merlin kernel: ACPI: SSDT CF6E021A, 00B8 (r1 FUJ FJNB1CF 1080000 FUJ 100) Nov 27 05:27:33 merlin kernel: Parsing all Control Methods: Nov 27 05:27:33 merlin kernel: Table [SSDT](id 002A) - 4 Objects with 0 Devices 3 Methods 0 Regions Nov 27 05:27:33 merlin kernel: ACPI: SSDT CF6E0740, 0047 (r1 FUJ FJNB1CF 1080000 FUJ 100) Nov 27 05:27:33 merlin kernel: Parsing all Control Methods: Nov 27 05:27:33 merlin kernel: Table [SSDT](id 002B) - 1 Objects with 0 Devices 1 Methods 0 Regions Nov 27 05:27:33 merlin kernel: ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) Nov 27 05:27:33 merlin kernel: Marking TSC unstable due to: TSC halts in idle. Nov 27 05:27:33 merlin kernel: Time: hpet clocksource has been installed. Nov 27 05:27:34 merlin kernel: input: Power Button (FF) as /class/input/input1 Nov 27 05:27:34 merlin kernel: ACPI: Power Button (FF) [PWRF] Nov 27 05:27:34 merlin kernel: input: Lid Switch as /class/input/input2 Nov 27 05:27:34 merlin kernel: ACPI: Lid Switch [LID] Nov 27 05:27:34 merlin kernel: input: Power Button (CM) as /class/input/input3 Nov 27 05:27:34 merlin kernel: input: PC Speaker as /class/input/input4 Nov 27 05:27:34 merlin kernel: ACPI: Power Button (CM) [PWRB] Nov 27 05:27:34 merlin kernel: input: Sleep Button (CM) as /class/input/input5 Nov 27 05:27:34 merlin kernel: USB Universal Host Controller Interface driver v3.0 Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 22 (level, low) -> IRQ 20 Nov 27 05:27:34 merlin kernel: PCI: Setting latency timer of device 0000:00:1a.0 to 64 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1a.0: UHCI Host Controller Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001840 Nov 27 05:27:34 merlin kernel: usb usb1: configuration #1 chosen from 1 choice Nov 27 05:27:34 merlin kernel: hub 1-0:1.0: USB hub found Nov 27 05:27:34 merlin kernel: ACPI: Sleep Button (CM) [SLPB] Nov 27 05:27:34 merlin kernel: hub 1-0:1.0: 2 ports detected Nov 27 05:27:34 merlin kernel: ACPI: EC: non-query interrupt received, switching to interrupt mode Nov 27 05:27:34 merlin kernel: 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Nov 27 05:27:34 merlin kernel: ACPI: Battery Slot [CMB1] (battery present) Nov 27 05:27:34 merlin kernel: ACPI: Battery Slot [CMB2] (battery absent) Nov 27 05:27:34 merlin kernel: input: Video Bus as /class/input/input6 Nov 27 05:27:34 merlin kernel: ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) Nov 27 05:27:34 merlin kernel: sdhci: Secure Digital Host Controller Interface driver Nov 27 05:27:34 merlin kernel: sdhci: Copyright(c) Pierre Ossman Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:00:1a.1[A] -> GSI 22 (level, low) -> IRQ 20 Nov 27 05:27:34 merlin kernel: PCI: Setting latency timer of device 0000:00:1a.1 to 64 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1a.1: UHCI Host Controller Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1a.1: irq 20, io base 0x00001860 Nov 27 05:27:34 merlin kernel: usb usb2: configuration #1 chosen from 1 choice Nov 27 05:27:34 merlin kernel: hub 2-0:1.0: USB hub found Nov 27 05:27:34 merlin kernel: hub 2-0:1.0: 2 ports detected Nov 27 05:27:34 merlin kernel: hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Nov 27 05:27:34 merlin kernel: Uniform CD-ROM driver Revision: 3.20 Nov 27 05:27:34 merlin kernel: ACPI: Thermal Zone [TZ00] (27 C) Nov 27 05:27:34 merlin kernel: ACPI: Thermal Zone [TZ01] (27 C) Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 22 (level, low) -> IRQ 20 Nov 27 05:27:34 merlin kernel: PCI: Setting latency timer of device 0000:00:1d.0 to 64 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001880 Nov 27 05:27:34 merlin kernel: pccard: PCMCIA card inserted into slot 1 Nov 27 05:27:34 merlin kernel: usb usb3: configuration #1 chosen from 1 choice Nov 27 05:27:34 merlin kernel: hub 3-0:1.0: USB hub found Nov 27 05:27:34 merlin kernel: hub 3-0:1.0: 2 ports detected Nov 27 05:27:34 merlin kernel: iwl4965: Intel(R) Wireless WiFi Link 4965AGN driver for Linux, 1.1.17ks Nov 27 05:27:34 merlin kernel: iwl4965: Copyright(c) 2003-2007 Intel Corporation Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:00:1d.1[A] -> GSI 22 (level, low) -> IRQ 20 Nov 27 05:27:34 merlin kernel: PCI: Setting latency timer of device 0000:00:1d.1 to 64 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1d.1: irq 20, io base 0x000018a0 Nov 27 05:27:34 merlin kernel: usb usb4: configuration #1 chosen from 1 choice Nov 27 05:27:34 merlin kernel: hub 4-0:1.0: USB hub found Nov 27 05:27:34 merlin kernel: hub 4-0:1.0: 2 ports detected Nov 27 05:27:34 merlin kernel: Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04793/0x302000 Nov 27 05:27:34 merlin kernel: serio: Synaptics pass-through port at isa0060/serio4/input0 Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:00:1d.2[A] -> GSI 22 (level, low) -> IRQ 20 Nov 27 05:27:34 merlin kernel: PCI: Setting latency timer of device 0000:00:1d.2 to 64 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5 Nov 27 05:27:34 merlin kernel: uhci_hcd 0000:00:1d.2: irq 20, io base 0x000018c0 Nov 27 05:27:34 merlin kernel: usb usb5: configuration #1 chosen from 1 choice Nov 27 05:27:34 merlin kernel: hub 5-0:1.0: USB hub found Nov 27 05:27:34 merlin kernel: hub 5-0:1.0: 2 ports detected Nov 27 05:27:34 merlin kernel: input: SynPS/2 Synaptics TouchPad as /class/input/input7 Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:04:03.4[A] -> GSI 16 (level, low) -> IRQ 16 Nov 27 05:27:34 merlin kernel: firewire_ohci: Added fw-ohci device 0000:04:03.4, OHCI version 1.10 Nov 27 05:27:34 merlin kernel: sdhci: SDHCI controller found at 0000:04:03.2 [1217:7120] (rev 2) Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:04:03.2[A] -> GSI 16 (level, low) -> IRQ 16 Nov 27 05:27:34 merlin kernel: sdhci:slot0: Unknown controller version (2). You may experience problems. Nov 27 05:27:34 merlin kernel: mmc0: SDHCI at 0xfe300000 irq 16 PIO Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 18 Nov 27 05:27:34 merlin kernel: PCI: Setting latency timer of device 0000:03:00.0 to 64 Nov 27 05:27:34 merlin kernel: iwl4965: Detected Intel Wireless WiFi Link 4965AGN Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 21 (level, low) -> IRQ 21 Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:00:1a.7[B] -> GSI 23 (level, low) -> IRQ 22 Nov 27 05:27:34 merlin kernel: PCI: Setting latency timer of device 0000:00:1a.7 to 64 Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1a.7: EHCI Host Controller Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6 Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1a.7: debug port 1 Nov 27 05:27:34 merlin kernel: PCI: cache line size of 32 is not supported by device 0000:00:1a.7 Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfe625800 Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 Nov 27 05:27:34 merlin kernel: usb usb6: configuration #1 chosen from 1 choice Nov 27 05:27:34 merlin kernel: cs: IO port probe 0x100-0x3af: excluding 0x2e8-0x2ef Nov 27 05:27:34 merlin kernel: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 Nov 27 05:27:34 merlin kernel: cs: IO port probe 0x820-0x8ff: clean. Nov 27 05:27:34 merlin kernel: cs: IO port probe 0xc00-0xcf7: clean. Nov 27 05:27:34 merlin kernel: cs: IO port probe 0xa00-0xaff: clean. Nov 27 05:27:34 merlin kernel: cs: memory probe 0xfe300000-0xfe3fffff:<6>hub 6-0:1.0: USB hub found Nov 27 05:27:34 merlin kernel: excluding 0xfe300000-0xfe30ffff<6>hub 6-0:1.0: 4 ports detected Nov 27 05:27:34 merlin kernel: Nov 27 05:27:34 merlin kernel: cs: IO port probe 0x100-0x3af: excluding 0x2e8-0x2ef Nov 27 05:27:34 merlin kernel: cs: IO port probe 0x3e0-0x4ff:<5>pcmcia: registering new device pcmcia1.0 Nov 27 05:27:34 merlin kernel: excluding 0x4d0-0x4d7 Nov 27 05:27:34 merlin kernel: cs: IO port probe 0x820-0x8ff: clean. Nov 27 05:27:34 merlin kernel: cs: IO port probe 0xc00-0xcf7: clean. Nov 27 05:27:34 merlin kernel: cs: IO port probe 0xa00-0xaff: clean. Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:00:1d.7[B] -> GSI 23 (level, low) -> IRQ 22 Nov 27 05:27:34 merlin kernel: PCI: Setting latency timer of device 0000:00:1d.7 to 64 Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1d.7: EHCI Host Controller Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7 Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1d.7: debug port 1 Nov 27 05:27:34 merlin kernel: PCI: cache line size of 32 is not supported by device 0000:00:1d.7 Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1d.7: irq 22, io mem 0xfe625c00 Nov 27 05:27:34 merlin kernel: ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 Nov 27 05:27:34 merlin kernel: usb usb7: configuration #1 chosen from 1 choice Nov 27 05:27:34 merlin kernel: hub 7-0:1.0: USB hub found Nov 27 05:27:34 merlin kernel: hub 7-0:1.0: 6 ports detected Nov 27 05:27:34 merlin kernel: iwl4965: Tunable channels: 13 802.11bg, 19 802.11a channels Nov 27 05:27:34 merlin kernel: phy0: Selected rate control algorithm 'iwl-4965-rs' Nov 27 05:27:34 merlin kernel: firewire_core: created new fw device fw0 (0 config rom retries, S400) Nov 27 05:27:34 merlin kernel: ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 21 Nov 27 05:27:34 merlin kernel: PCI: Setting latency timer of device 0000:00:1b.0 to 64 Nov 27 05:27:34 merlin kernel: hda_codec: Unknown model for ALC262, trying auto-probe from BIOS... Nov 27 05:27:34 merlin kernel: Clocksource tsc unstable (delta = -68239676 ns) Nov 27 05:27:34 merlin kernel: usb 1-2: new full speed USB device using uhci_hcd and address 2 Nov 27 05:27:34 merlin kernel: usb 1-2: configuration #1 chosen from 1 choice Nov 27 05:27:34 merlin kernel: Adding 4000176k swap on /dev/scsi/host0/bus0/target0/lun0/part2. Priority:-1 extents:1 across:4000176k Nov 27 05:27:34 merlin kernel: Bluetooth: Core ver 2.11 Nov 27 05:27:34 merlin kernel: NET: Registered protocol family 31 Nov 27 05:27:34 merlin kernel: Bluetooth: HCI device and connection manager initialized Nov 27 05:27:34 merlin kernel: Bluetooth: HCI socket layer initialized Nov 27 05:27:34 merlin kernel: Bluetooth: HCI USB driver ver 2.9 Nov 27 05:27:34 merlin kernel: usb 2-1: new full speed USB device using uhci_hcd and address 2 Nov 27 05:27:34 merlin kernel: EXT3 FS on sda3, internal journal Nov 27 05:27:34 merlin kernel: usb 2-1: configuration #1 chosen from 1 choice Nov 27 05:27:34 merlin kernel: usbcore: registered new interface driver hci_usb Nov 27 05:27:34 merlin kernel: usbcore: registered new interface driver usbserial Nov 27 05:27:34 merlin kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for generic Nov 27 05:27:34 merlin kernel: usbcore: registered new interface driver usbserial_generic Nov 27 05:27:34 merlin kernel: drivers/usb/serial/usb-serial.c: USB Serial Driver core Nov 27 05:27:34 merlin kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (1 port) Nov 27 05:27:34 merlin kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (3 port) Nov 27 05:27:35 merlin kernel: sierra 2-1:1.0: Sierra USB modem (3 port) converter detected Nov 27 05:27:35 merlin kernel: usb 2-1: Sierra USB modem (3 port) converter now attached to ttyUSB0 Nov 27 05:27:35 merlin kernel: usb 2-1: Sierra USB modem (3 port) converter now attached to ttyUSB1 Nov 27 05:27:35 merlin kernel: usb 2-1: Sierra USB modem (3 port) converter now attached to ttyUSB2 Nov 27 05:27:35 merlin kernel: usbcore: registered new interface driver sierra Nov 27 05:27:35 merlin kernel: drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.2.5b Nov 27 05:27:35 merlin kernel: Real Time Clock Driver v1.12ac Nov 27 05:27:35 merlin kernel: input: PS/2 Generic Mouse as /class/input/input8 Nov 27 05:29:59 merlin kernel: acpi-cpufreq: acpi_cpufreq_init Nov 27 05:29:59 merlin kernel: acpi-cpufreq: acpi_cpufreq_early_init Nov 27 05:29:59 merlin kernel: cpufreq-core: trying to register driver acpi-cpufreq Nov 27 05:29:59 merlin kernel: cpufreq-core: adding CPU 0 Nov 27 05:29:59 merlin kernel: acpi-cpufreq: acpi_cpufreq_cpu_init Nov 27 05:29:59 merlin kernel: acpi-cpufreq: HARDWARE addr space Nov 27 05:29:59 merlin kernel: freq-table: table entry 0: 2401000 kHz, 0 index Nov 27 05:29:59 merlin kernel: freq-table: table entry 1: 2400000 kHz, 1 index Nov 27 05:29:59 merlin kernel: freq-table: table entry 2: 2000000 kHz, 2 index Nov 27 05:29:59 merlin kernel: freq-table: table entry 3: 1600000 kHz, 3 index Nov 27 05:29:59 merlin kernel: freq-table: table entry 4: 1200000 kHz, 4 index Nov 27 05:29:59 merlin kernel: freq-table: table entry 5: 800000 kHz, 5 index Nov 27 05:29:59 merlin kernel: acpi-cpufreq: get_cur_freq_on_cpu (0) Nov 27 05:29:59 merlin kernel: acpi-cpufreq: get_cur_val = 103943207 Nov 27 05:29:59 merlin kernel: acpi-cpufreq: cur freq = 2400000 Nov 27 05:29:59 merlin kernel: acpi-cpufreq: CPU0 - ACPI performance management activated. Nov 27 05:29:59 merlin kernel: acpi-cpufreq: *P0: 2401 MHz, 35000 mW, 10 uS Nov 27 05:29:59 merlin kernel: acpi-cpufreq: P1: 2400 MHz, 35000 mW, 10 uS Nov 27 05:29:59 merlin kernel: acpi-cpufreq: P2: 2000 MHz, 28000 mW, 10 uS Nov 27 05:29:59 merlin kernel: acpi-cpufreq: P3: 1600 MHz, 22000 mW, 10 uS Nov 27 05:29:59 merlin kernel: acpi-cpufreq: P4: 1200 MHz, 16000 mW, 10 uS Nov 27 05:29:59 merlin kernel: acpi-cpufreq: P5: 800 MHz, 14000 mW, 10 uS Nov 27 05:29:59 merlin kernel: freq-table: setting show_table for cpu 0 to f7ffa6c0 Nov 27 05:29:59 merlin kernel: cpufreq-core: CPU 1 already managed, adding link Nov 27 05:29:59 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:29:59 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:29:59 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:29:59 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:29:59 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:29:59 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:29:59 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:29:59 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 2401000 kHz Nov 27 05:29:59 merlin kernel: cpufreq-core: governor switch Nov 27 05:29:59 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 1 Nov 27 05:29:59 merlin kernel: performance: setting to 2401000 kHz because of event 1 Nov 27 05:29:59 merlin kernel: cpufreq-core: target for CPU 0: 2401000 kHz, relation 1 Nov 27 05:29:59 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 2401000 (0) Nov 27 05:29:59 merlin kernel: freq-table: request for target 2401000 kHz (relation: 1) for cpu 0 Nov 27 05:29:59 merlin kernel: freq-table: target is 0 (2401000 kHz, 0) Nov 27 05:29:59 merlin kernel: acpi-cpufreq: Called after resume, resetting to P0 Nov 27 05:29:59 merlin kernel: cpufreq-core: notification 0 of frequency transition to 2401000 kHz Nov 27 05:29:59 merlin kernel: cpufreq-core: notification 0 of frequency transition to 2401000 kHz Nov 27 05:29:59 merlin kernel: cpufreq-core: notification 1 of frequency transition to 2401000 kHz Nov 27 05:29:59 merlin kernel: cpufreq-core: notification 1 of frequency transition to 2401000 kHz Nov 27 05:29:59 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:29:59 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:29:59 merlin kernel: performance: setting to 2401000 kHz because of event 3 Nov 27 05:29:59 merlin kernel: cpufreq-core: target for CPU 0: 2401000 kHz, relation 1 Nov 27 05:29:59 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 2401000 (0) Nov 27 05:29:59 merlin kernel: freq-table: request for target 2401000 kHz (relation: 1) for cpu 0 Nov 27 05:29:59 merlin kernel: freq-table: target is 0 (2401000 kHz, 0) Nov 27 05:29:59 merlin kernel: acpi-cpufreq: Already at target state (P0) Nov 27 05:29:59 merlin kernel: cpufreq-core: initialization complete Nov 27 05:29:59 merlin kernel: cpufreq-core: adding CPU 1 Nov 27 05:29:59 merlin kernel: cpufreq-core: driver acpi-cpufreq up and running Nov 27 05:29:59 merlin kernel: acpi-cpufreq: get_cur_freq_on_cpu (0) Nov 27 05:29:59 merlin kernel: acpi-cpufreq: get_cur_val = 103943207 Nov 27 05:29:59 merlin kernel: acpi-cpufreq: cur freq = 2400000 Nov 27 05:31:52 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:31:52 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:31:52 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:31:52 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:31:52 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:31:52 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:31:52 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:31:52 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 2401000 kHz Nov 27 05:31:52 merlin kernel: cpufreq-core: governor switch Nov 27 05:31:52 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 2 Nov 27 05:31:52 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 1 Nov 27 05:31:52 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:31:52 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:31:52 merlin kernel: printk: 3 messages suppressed. Nov 27 05:31:52 merlin kernel: acpi-cpufreq: cpu 0: performance percent 104 Nov 27 05:31:52 merlin kernel: cpufreq-core: target for CPU 0: 356720 kHz, relation 0 Nov 27 05:31:52 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 356720 (0) Nov 27 05:31:52 merlin kernel: freq-table: request for target 356720 kHz (relation: 0) for cpu 0 Nov 27 05:31:52 merlin kernel: freq-table: target is 5 (800000 kHz, 5) Nov 27 05:31:52 merlin kernel: cpufreq-core: notification 0 of frequency transition to 800000 kHz Nov 27 05:31:52 merlin kernel: cpufreq-core: notification 0 of frequency transition to 800000 kHz Nov 27 05:31:52 merlin kernel: cpufreq-core: notification 1 of frequency transition to 800000 kHz Nov 27 05:31:52 merlin kernel: cpufreq-core: notification 1 of frequency transition to 800000 kHz Nov 27 05:31:55 merlin kernel: cpufreq-core: updating policy for CPU 0 Nov 27 05:31:55 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:31:55 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:31:55 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:31:55 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:31:55 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:31:55 merlin kernel: freq-table: request for verification of policy (800000 - 2400000 kHz) for cpu 0 Nov 27 05:31:55 merlin kernel: freq-table: verification lead to (800000 - 2400000 kHz) for cpu 0 Nov 27 05:31:55 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 2400000 kHz Nov 27 05:31:55 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:31:55 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:31:55 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:31:55 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:31:55 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:31:55 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:31:55 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:31:55 merlin kernel: freq-table: request for verification of policy (800000 - 2400000 kHz) for cpu 0 Nov 27 05:31:55 merlin kernel: freq-table: verification lead to (800000 - 2400000 kHz) for cpu 0 Nov 27 05:31:55 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 2400000 kHz Nov 27 05:31:55 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:31:55 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:32:08 merlin kernel: printk: 8 messages suppressed. Nov 27 05:32:08 merlin kernel: cpufreq-core: target for CPU 0: 2400000 kHz, relation 1 Nov 27 05:32:08 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 2400000 (0) Nov 27 05:32:08 merlin kernel: freq-table: request for target 2400000 kHz (relation: 1) for cpu 0 Nov 27 05:32:14 merlin kernel: printk: 14 messages suppressed. Nov 27 05:32:14 merlin kernel: acpi-cpufreq: get_cur_freq_on_cpu (0) Nov 27 05:32:20 merlin kernel: printk: 5 messages suppressed. Nov 27 05:32:20 merlin kernel: cpufreq-core: target for CPU 0: 2400000 kHz, relation 1 Nov 27 05:32:23 merlin kernel: printk: 16 messages suppressed. Nov 27 05:32:23 merlin kernel: cpufreq-core: target for CPU 0: 2400000 kHz, relation 1 Nov 27 05:32:27 merlin kernel: printk: 101 messages suppressed. Nov 27 05:32:27 merlin kernel: cpufreq-core: target for CPU 0: 2400000 kHz, relation 1 Nov 27 05:32:35 merlin kernel: printk: 33 messages suppressed. Nov 27 05:32:35 merlin kernel: cpufreq-core: updating policy for CPU 0 Nov 27 05:32:35 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:32:35 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:32:35 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:32:35 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:32:35 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:32:35 merlin kernel: freq-table: request for verification of policy (800000 - 2000000 kHz) for cpu 0 Nov 27 05:32:35 merlin kernel: freq-table: verification lead to (800000 - 2000000 kHz) for cpu 0 Nov 27 05:32:35 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 2000000 kHz Nov 27 05:32:35 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:32:35 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:32:35 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:32:35 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:32:35 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:32:35 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:32:35 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:32:35 merlin kernel: freq-table: request for verification of policy (800000 - 2000000 kHz) for cpu 0 Nov 27 05:32:35 merlin kernel: freq-table: verification lead to (800000 - 2000000 kHz) for cpu 0 Nov 27 05:32:35 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 2000000 kHz Nov 27 05:32:35 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:32:35 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:32:41 merlin kernel: printk: 8 messages suppressed. Nov 27 05:32:41 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:33:18 merlin kernel: printk: 16 messages suppressed. Nov 27 05:33:18 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:33:18 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 2000000 (0) Nov 27 05:33:18 merlin kernel: freq-table: request for target 2000000 kHz (relation: 1) for cpu 0 Nov 27 05:33:18 merlin kernel: freq-table: target is 2 (2000000 kHz, 2) Nov 27 05:33:18 merlin kernel: cpufreq-core: notification 0 of frequency transition to 2000000 kHz Nov 27 05:33:18 merlin kernel: cpufreq-core: notification 0 of frequency transition to 2000000 kHz Nov 27 05:33:18 merlin kernel: cpufreq-core: notification 1 of frequency transition to 2000000 kHz Nov 27 05:33:18 merlin kernel: cpufreq-core: notification 1 of frequency transition to 2000000 kHz Nov 27 05:33:28 merlin kernel: printk: 9 messages suppressed. Nov 27 05:33:28 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:33:28 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 2000000 (0) Nov 27 05:33:34 merlin kernel: printk: 92 messages suppressed. Nov 27 05:33:34 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:33:41 merlin kernel: printk: 16 messages suppressed. Nov 27 05:33:41 merlin kernel: acpi-cpufreq: get_cur_freq_on_cpu (0) Nov 27 05:33:43 merlin kernel: printk: 5 messages suppressed. Nov 27 05:33:43 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:33:55 merlin kernel: printk: 76 messages suppressed. Nov 27 05:33:55 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:33:55 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 2000000 (0) Nov 27 05:33:57 merlin kernel: printk: 32 messages suppressed. Nov 27 05:33:57 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:34:03 merlin kernel: printk: 101 messages suppressed. Nov 27 05:34:03 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:34:07 merlin kernel: printk: 16 messages suppressed. Nov 27 05:34:07 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:34:14 merlin kernel: printk: 84 messages suppressed. Nov 27 05:34:14 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:34:27 merlin kernel: printk: 16 messages suppressed. Nov 27 05:34:27 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:34:27 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 2000000 (0) Nov 27 05:34:27 merlin kernel: freq-table: request for target 2000000 kHz (relation: 1) for cpu 0 Nov 27 05:35:00 merlin kernel: printk: 31 messages suppressed. Nov 27 05:35:00 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:35:00 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 2000000 (0) Nov 27 05:35:00 merlin kernel: freq-table: request for target 2000000 kHz (relation: 1) for cpu 0 Nov 27 05:35:00 merlin kernel: freq-table: target is 2 (2000000 kHz, 2) Nov 27 05:35:00 merlin kernel: cpufreq-core: notification 0 of frequency transition to 2000000 kHz Nov 27 05:35:00 merlin kernel: cpufreq-core: notification 0 of frequency transition to 2000000 kHz Nov 27 05:35:04 merlin kernel: printk: 11 messages suppressed. Nov 27 05:35:04 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:35:11 merlin kernel: printk: 33 messages suppressed. Nov 27 05:35:11 merlin kernel: cpufreq-core: target for CPU 0: 2000000 kHz, relation 1 Nov 27 05:35:16 merlin kernel: printk: 7 messages suppressed. Nov 27 05:35:16 merlin kernel: cpufreq-core: updating policy for CPU 0 Nov 27 05:35:16 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:35:16 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:16 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:16 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:16 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:16 merlin kernel: freq-table: request for verification of policy (800000 - 1600000 kHz) for cpu 0 Nov 27 05:35:16 merlin kernel: freq-table: verification lead to (800000 - 1600000 kHz) for cpu 0 Nov 27 05:35:16 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 1600000 kHz Nov 27 05:35:16 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:35:16 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:35:16 merlin kernel: cpufreq-core: target for CPU 0: 1600000 kHz, relation 1 Nov 27 05:35:16 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 1600000 (0) Nov 27 05:35:16 merlin kernel: freq-table: request for target 1600000 kHz (relation: 1) for cpu 0 Nov 27 05:35:16 merlin kernel: freq-table: target is 3 (1600000 kHz, 3) Nov 27 05:35:16 merlin kernel: cpufreq-core: notification 0 of frequency transition to 1600000 kHz Nov 27 05:35:16 merlin kernel: cpufreq-core: notification 0 of frequency transition to 1600000 kHz Nov 27 05:35:16 merlin kernel: cpufreq-core: notification 1 of frequency transition to 1600000 kHz Nov 27 05:35:16 merlin kernel: cpufreq-core: notification 1 of frequency transition to 1600000 kHz Nov 27 05:35:16 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:35:16 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:16 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:16 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:16 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:16 merlin kernel: freq-table: request for verification of policy (800000 - 1600000 kHz) for cpu 0 Nov 27 05:35:16 merlin kernel: freq-table: verification lead to (800000 - 1600000 kHz) for cpu 0 Nov 27 05:35:16 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 1600000 kHz Nov 27 05:35:16 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:35:16 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:35:36 merlin kernel: printk: 8 messages suppressed. Nov 27 05:35:36 merlin kernel: cpufreq-core: updating policy for CPU 0 Nov 27 05:35:36 merlin kernel: acpi-cpufreq: get_cur_freq_on_cpu (0) Nov 27 05:35:36 merlin kernel: acpi-cpufreq: get_cur_val = 100665373 Nov 27 05:35:36 merlin kernel: acpi-cpufreq: cur freq = 1600000 Nov 27 05:35:36 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:35:36 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:36 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:36 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:36 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:36 merlin kernel: freq-table: request for verification of policy (800000 - 1200000 kHz) for cpu 0 Nov 27 05:35:36 merlin kernel: freq-table: verification lead to (800000 - 1200000 kHz) for cpu 0 Nov 27 05:35:36 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 1200000 kHz Nov 27 05:35:36 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:35:36 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:35:36 merlin kernel: cpufreq-core: target for CPU 0: 1200000 kHz, relation 1 Nov 27 05:35:36 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 1200000 (0) Nov 27 05:35:36 merlin kernel: freq-table: request for target 1200000 kHz (relation: 1) for cpu 0 Nov 27 05:35:36 merlin kernel: freq-table: target is 4 (1200000 kHz, 4) Nov 27 05:35:36 merlin kernel: cpufreq-core: notification 0 of frequency transition to 1200000 kHz Nov 27 05:35:36 merlin kernel: cpufreq-core: notification 0 of frequency transition to 1200000 kHz Nov 27 05:35:36 merlin kernel: cpufreq-core: notification 1 of frequency transition to 1200000 kHz Nov 27 05:35:36 merlin kernel: cpufreq-core: notification 1 of frequency transition to 1200000 kHz Nov 27 05:35:36 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:35:36 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:36 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:36 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:36 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:36 merlin kernel: freq-table: request for verification of policy (800000 - 1200000 kHz) for cpu 0 Nov 27 05:35:36 merlin kernel: freq-table: verification lead to (800000 - 1200000 kHz) for cpu 0 Nov 27 05:35:36 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 1200000 kHz Nov 27 05:35:36 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:35:36 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:35:46 merlin kernel: printk: 5 messages suppressed. Nov 27 05:35:46 merlin kernel: cpufreq-core: updating policy for CPU 0 Nov 27 05:35:46 merlin kernel: acpi-cpufreq: get_cur_freq_on_cpu (0) Nov 27 05:35:46 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:35:46 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:46 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:46 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:46 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:46 merlin kernel: freq-table: request for verification of policy (800000 - 800000 kHz) for cpu 0 Nov 27 05:35:46 merlin kernel: freq-table: verification lead to (800000 - 800000 kHz) for cpu 0 Nov 27 05:35:46 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 800000 kHz Nov 27 05:35:46 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:35:46 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:35:46 merlin kernel: cpufreq-core: target for CPU 0: 800000 kHz, relation 1 Nov 27 05:35:46 merlin kernel: acpi-cpufreq: acpi_cpufreq_target 800000 (0) Nov 27 05:35:46 merlin kernel: freq-table: request for target 800000 kHz (relation: 1) for cpu 0 Nov 27 05:35:46 merlin kernel: freq-table: target is 5 (800000 kHz, 5) Nov 27 05:35:46 merlin kernel: cpufreq-core: notification 0 of frequency transition to 800000 kHz Nov 27 05:35:46 merlin kernel: cpufreq-core: notification 0 of frequency transition to 800000 kHz Nov 27 05:35:46 merlin kernel: cpufreq-core: notification 1 of frequency transition to 800000 kHz Nov 27 05:35:46 merlin kernel: cpufreq-core: notification 1 of frequency transition to 800000 kHz Nov 27 05:35:46 merlin kernel: cpufreq-core: setting new policy for CPU 0: 800000 - 2401000 kHz Nov 27 05:35:46 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:46 merlin kernel: freq-table: request for verification of policy (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:46 merlin kernel: freq-table: verification lead to (800000 - 2401000 kHz) for cpu 0 Nov 27 05:35:46 merlin kernel: acpi-cpufreq: acpi_cpufreq_verify Nov 27 05:35:46 merlin kernel: freq-table: request for verification of policy (800000 - 800000 kHz) for cpu 0 Nov 27 05:35:46 merlin kernel: freq-table: verification lead to (800000 - 800000 kHz) for cpu 0 Nov 27 05:35:46 merlin kernel: cpufreq-core: new min and max freqs are 800000 - 800000 kHz Nov 27 05:35:46 merlin kernel: cpufreq-core: governor: change or update limits Nov 27 05:35:46 merlin kernel: cpufreq-core: __cpufreq_governor for CPU 0, event 3 Nov 27 05:35:53 merlin kernel: printk: 7 messages suppressed. Nov 27 05:35:53 merlin kernel: acpi-cpufreq: get_cur_freq_on_cpu (0) Nov 27 05:35:53 merlin kernel: acpi-cpufreq: get_cur_val = 100698127
_______________________________________________
Cpufreq mailing list
[email protected]
http://lists.linux.org.uk/mailman/listinfo/cpufreq
Quoted 18 lines · Michael Reinelt
Hi Dave,
thanks for your answer!
Quoted 7 lines
Quoted 5 lines
When I boot the notebook into single-user mode
(using vanilla 2.6.23 or 2.6.24-rc3), with no modules loaded, the cpu runs at 2.4GHz. As soon as I laod the acpi-cpufreq module, the upper limit falls in some steps (2 GHz, 1200MHz) to 800 MHz. Note that there is neither acpid nor any powersave daemon running!Do you have
CONFIG_CPU_FREQ_GOV_ONDEMANDenabled in your kernel ?Yes, but as a module.
Quoted 4 lines
Quoted 3 lines
At the moment my workaround is *not* to load acpi-cpufreq, so the CPU stays at 2.4GHz all the time, but I really want to use powersaving with the machine....
Quoted 9 lines
Quoted 2 lines
I'm confused. It sounds like you _are_ using power saving. The whole purpose of cpufreq is to lower the cpu speed when idle.
I _want_ to use powersaving, but I can't, because I'd be stuck at 800 MHz.
Quoted 2 lines
If you run some cpu intensive load like a big compile, does the speed go back up ?
No, it does not.
Quoted 1 line
the cpufreq.debug=7 logs would be a good start.
It is probably limited through _PPC again.
Dave, Len: Can you please add the patch that _PPC changes are printed with cpufreq.debug, pls.
I posted this a while ago on the cpufreq list:
Subject: [PATCH] Print _PPC changes via cpufreq debug layer
http://article.gmane.org/gmane.linux.kernel.cpufreq/5642
Thanks,
Thomas
Hi THomas,
Quoted 6 lines
It is probably limited through
_PPCagain.
Dave, Len: Can you please add the patch that_PPCchanges are printed with cpufreq.debug, pls.
I posted this a while ago on the cpufreq list:
Subject: [PATCH] Print_PPCchanges via cpufreq debug layer
http://article.gmane.org/gmane.linux.kernel.cpufreq/5642
Looks like it is :-(
I applied your patch and did the debugging again, and found the following:
merlin.merlin.local:/home/michi # grep PPC Lifebook.syslog*
cpufreq-core: CPU 0: _PPC is 0 - frequency not limited
cpufreq-core: CPU 1: _PPC is 0 - frequency not limited
cpufreq-core: CPU 0: _PPC is 1 - frequency limited
cpufreq-core: CPU 1: _PPC is 1 - frequency limited
cpufreq-core: CPU 0: _PPC is 2 - frequency limited
cpufreq-core: CPU 1: _PPC is 2 - frequency limited
cpufreq-core: CPU 0: _PPC is 3 - frequency limited
cpufreq-core: CPU 1: _PPC is 3 - frequency limited
cpufreq-core: CPU 0: _PPC is 4 - frequency limited
cpufreq-core: CPU 1: _PPC is 4 - frequency limited
cpufreq-core: CPU 0: _PPC is 5 - frequency limited
the first PPC message appears where acpi_cpufreq isn't even loaded. As I found these tables in the debug output:
freq-table: table entry 0: 2401000 kHz, 0 index
freq-table: table entry 1: 2400000 kHz, 1 index
freq-table: table entry 2: 2000000 kHz, 2 index
freq-table: table entry 3: 1600000 kHz, 3 index
freq-table: table entry 4: 1200000 kHz, 4 index
freq-table: table entry 5: 800000 kHz, 5 index
acpi-cpufreq: *P0: 2401 MHz, 35000 mW, 10 uS acpi-cpufreq: P1: 2400 MHz, 35000 mW, 10 uS acpi-cpufreq: P2: 2000 MHz, 28000 mW, 10 uS acpi-cpufreq: P3: 1600 MHz, 22000 mW, 10 uS acpi-cpufreq: P4: 1200 MHz, 16000 mW, 10 uS acpi-cpufreq: P5: 800 MHz, 14000 mW, 10 uS
as the reported _PPC value shows up after the corresponding P state has been entered, I guess thats the reason for my problem: Looks like my notebook can enter a certain P-state, but can never leave it towards a higher frequency.
so...
- wtf is _PPC?
- does this look like a BIOS bug?
- i remember seeing some sort of "disable _PPC by a specific module parameter" patch somewhere... "ignore_ppc" or something... is this an "official" patch which is worth to give it a try? Somebody knows an official location for this patch?
I'm happily looking forward to get this issue solved!
thanks, Michael
Signature · 4 lines
Michael Reinelt <[email protected]> http://home.pages.at/reinelt GPG-Key 0xDF13BA50 ICQ #288386781
Quoted 43 lines · Michael Reinelt
Hi THomas,
Quoted 6 lines
It is probably limited through
_PPCagain.
Dave, Len: Can you please add the patch that_PPCchanges are printed with cpufreq.debug, pls.
I posted this a while ago on the cpufreq list:
Subject: [PATCH] Print_PPCchanges via cpufreq debug layer
http://article.gmane.org/gmane.linux.kernel.cpufreq/5642Looks like it is :-(
I applied your patch and did the debugging again, and found the following:
merlin.merlin.local:/home/michi # grep PPC Lifebook.syslog*
cpufreq-core: CPU 0:_PPCis 0 - frequency not limited
cpufreq-core: CPU 1:_PPCis 0 - frequency not limited
cpufreq-core: CPU 0:_PPCis 1 - frequency limited
cpufreq-core: CPU 1:_PPCis 1 - frequency limited
cpufreq-core: CPU 0:_PPCis 2 - frequency limited
cpufreq-core: CPU 1:_PPCis 2 - frequency limited
cpufreq-core: CPU 0:_PPCis 3 - frequency limited
cpufreq-core: CPU 1:_PPCis 3 - frequency limited
cpufreq-core: CPU 0:_PPCis 4 - frequency limited
cpufreq-core: CPU 1:_PPCis 4 - frequency limited
cpufreq-core: CPU 0:_PPCis 5 - frequency limitedthe first PPC message appears where
acpi_cpufreqisn't even loaded. As I found these tables in the debug output:freq-table: table entry 0: 2401000 kHz, 0 index
freq-table: table entry 1: 2400000 kHz, 1 index
freq-table: table entry 2: 2000000 kHz, 2 index
freq-table: table entry 3: 1600000 kHz, 3 index
freq-table: table entry 4: 1200000 kHz, 4 index
freq-table: table entry 5: 800000 kHz, 5 indexacpi-cpufreq: *P0: 2401 MHz, 35000 mW, 10 uS acpi-cpufreq: P1: 2400 MHz, 35000 mW, 10 uS acpi-cpufreq: P2: 2000 MHz, 28000 mW, 10 uS acpi-cpufreq: P3: 1600 MHz, 22000 mW, 10 uS acpi-cpufreq: P4: 1200 MHz, 16000 mW, 10 uS acpi-cpufreq: P5: 800 MHz, 14000 mW, 10 uS
Quoted 8 lines
as the reported
_PPCvalue shows up after the corresponding P state has been entered, I guess thats the reason for my problem: Looks like my notebook can enter a certain P-state, but can never leave it towards a higher frequency.so...
- wtf is
_PPC?
An interface that your BIOS uses to tell the OS that not all freqs are allowed to be used (1 means do not allow highest freq, 2 do not allow the two highest, and so on).
Quoted 2 lines
- does this look like a BIOS bug?
Possibly...
Searching for the latest BIOS should be your first step... Also have a look at your BIOS configs, there might be something to adjust with SpeedStep, CPU Freq, GV1/GV3 (is this only happening on battery, then you may have some "battery optimized freq" setting set).
If this does not help you should open a bug on bugzilla.kernel.org, assign it to the ACPI component and attach acpidump output. You may want to CC me then, maybe we see the reason why _PPC is increased by having a look at the ACPI tables...
Quoted 4 lines
- i remember seeing some sort of "disable
_PPCby a specific module parameter" patch somewhere... "ignore_ppc" or something... is this an "official" patch which is worth to give it a try? Somebody knows an official location for this patch?
IIRC I posted such a patch, but using it thoughtlessly, it will override your BIOS suggestions in a way that the machine is running hotter as it should..., therefore I am not convinced anymore it should be added.
Thomas
Quoted 79 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Thomas Renninger
Sent: Tuesday, November 27, 2007 6:54 AM
To: Michael Reinelt
Cc: Dave Jones; [email protected]
Subject: Re: Core2Duo locked at 800MHzQuoted 4 lines · Michael Reinelt
Hi THomas,
Quoted 2 lines
It is probably limited through
_PPCagain.
Dave, Len: Can you please add the patch that_PPCchangesare printed
Quoted 8 lines
Quoted 4 lines
with cpufreq.debug, pls.
I posted this a while ago on the cpufreq list:
Subject: [PATCH] Print_PPCchanges via cpufreq debug layer
http://article.gmane.org/gmane.linux.kernel.cpufreq/5642Looks like it is :-(
I applied your patch and did the debugging again, and found
the following:
Quoted 14 lines
merlin.merlin.local:/home/michi # grep PPC Lifebook.syslog*
cpufreq-core: CPU 0:_PPCis 0 - frequency not limited
cpufreq-core: CPU 1:_PPCis 0 - frequency not limited
cpufreq-core: CPU 0:_PPCis 1 - frequency limited
cpufreq-core: CPU 1:_PPCis 1 - frequency limited
cpufreq-core: CPU 0:_PPCis 2 - frequency limited
cpufreq-core: CPU 1:_PPCis 2 - frequency limited
cpufreq-core: CPU 0:_PPCis 3 - frequency limited
cpufreq-core: CPU 1:_PPCis 3 - frequency limited
cpufreq-core: CPU 0:_PPCis 4 - frequency limited
cpufreq-core: CPU 1:_PPCis 4 - frequency limited
cpufreq-core: CPU 0:_PPCis 5 - frequency limitedQuoted 1 line
the first PPC message appears where
acpi_cpufreqisn't evenloaded. As I
Quoted 9 lines
found these tables in the debug output:
freq-table: table entry 0: 2401000 kHz, 0 index
freq-table: table entry 1: 2400000 kHz, 1 index
freq-table: table entry 2: 2000000 kHz, 2 index
freq-table: table entry 3: 1600000 kHz, 3 index
freq-table: table entry 4: 1200000 kHz, 4 index
freq-table: table entry 5: 800000 kHz, 5 indexQuoted 8 lines
acpi-cpufreq: *P0: 2401 MHz, 35000 mW, 10 uS acpi-cpufreq: P1: 2400 MHz, 35000 mW, 10 uS acpi-cpufreq: P2: 2000 MHz, 28000 mW, 10 uS acpi-cpufreq: P3: 1600 MHz, 22000 mW, 10 uS acpi-cpufreq: P4: 1200 MHz, 16000 mW, 10 uS acpi-cpufreq: P5: 800 MHz, 14000 mW, 10 uSas the reported
_PPCvalue shows up after the correspondingP state has
Quoted 2 lines
been entered, I guess thats the reason for my problem: Looks like my notebook can enter a certain P-state, but can never leave it
towards a
Quoted 5 lines
higher frequency.
so...
- wtf is
_PPC?An interface that your BIOS uses to tell the OS that not all freqs are allowed to be used (1 means do not allow highest freq, 2 do not allow the two highest, and so on).
Quoted 2 lines
- does this look like a BIOS bug?
Possibly...
Searching for the latest BIOS should be your first step... Also have a look at your BIOS configs, there might be something to adjust with SpeedStep, CPU Freq, GV1/GV3 (is this only happening on battery, then you may have some "battery optimized freq" setting set).
Quoted 5 lines
If this does not help you should open a bug on bugzilla.kernel.org, assign it to the ACPI component and attach acpidump output. You may want to CC me then, maybe we see the reason why
_PPCis increased by having a look at the ACPI tables...
Also, Are you running on battery or AC power when you see this problem. Typically BIOSes reduce freq when in battery mode.
Thanks,
Venki
Quoted 8 lines · Thomas Renninger
Quoted 1 line
Quoted 1 line
the cpufreq.debug=7 logs would be a good start.
It is probably limited through
_PPCagain.
Dave, Len: Can you please add the patch that_PPCchanges are printed with cpufreq.debug, pls.
I posted this a while ago on the cpufreq list:
Subject: [PATCH] Print_PPCchanges via cpufreq debug layer
http://article.gmane.org/gmane.linux.kernel.cpufreq/5642
Looks ok to me. Len, you ok with me merging this? Or would you rather it went through the acpi git tree?
Dave
Signature · 1 line
http://www.codemonkey.org.uk