Skip to contentSkip to conversation

ATA bus error with external hd on esata

DISCUSSION Zsolt Barat 4 participants 7 messages Dec 15, 2007 – Dec 18, 2007 1 message not in the archive libata

lore
Share & tools
lore
#0 lore raw

hi list,
i just bought a "MyBook" called external HD with a fixed enclosure, from WD. Connected to the SATA port i constantly get "ATA bus error" messages in the kernel log. Is this a known issue?

/var/log/messages:

Dec 15 18:37:53 proto1 ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x2
Dec 15 18:37:53 proto1 ata2.00: irq_stat 0x40000001
Dec 15 18:37:53 proto1 ata2.00: cmd 35/00:e0:a7:d2:01/00:01:33:00:00/e0
tag 0 cdb 0x0 data 245760 out
Dec 15 18:37:53 proto1 res 51/84:00:86:d4:01/00:00:33:00:00/e0 Emask
0x10 (ATA bus error)
Dec 15 18:37:54 proto1 ata2: soft resetting port
Dec 15 18:37:54 proto1 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
310)
Dec 15 18:37:54 proto1 ata2.00: configured for UDMA/33
Dec 15 18:37:54 proto1 ata2: EH complete
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] 976773168 512-byte hardware
sectors (500108 MB)
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] Write Protect is off
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Dec 15 18:38:15 proto1 ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x2
Dec 15 18:38:15 proto1 ata2.00: irq_stat 0x40000001
Dec 15 18:38:15 proto1 ata2.00: cmd 35/00:80:bf:09:14/00:01:33:00:00/e0
tag 0 cdb 0x0 data 196608 out
Dec 15 18:38:15 proto1 res 51/84:00:3e:0b:14/00:00:33:00:00/e0 Emask
0x10 (ATA bus error)
Dec 15 18:38:15 proto1 ata2: soft resetting port
Dec 15 18:38:15 proto1 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
310)
Dec 15 18:38:15 proto1 ata2.00: configured for UDMA/33
Dec 15 18:38:15 proto1 ata2: EH complete
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] 976773168 512-byte hardware
sectors (500108 MB)
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] Write Protect is off
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] Write cache: enabled, read

cache: enabled, doesn't support DPO or FUA

lspci:
00:00.0 Host bridge: ATI Technologies Inc Unknown device 7910 00:01.0 PCI bridge: ATI Technologies Inc Unknown device 7912 00:07.0 PCI bridge: ATI Technologies Inc Unknown device 7917 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SB600 SMBus (rev 13) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SB600 Azalia
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SB600 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon X1200 Series 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev c0)

thanks and best regards

zsolt

#1 lore raw
Quoted 75 lines · Zsolt Barat

hi list,
i just bought a "MyBook" called external HD with a fixed enclosure, from WD. Connected to the SATA port i constantly get "ATA bus error" messages in the kernel log. Is this a known issue?

/var/log/messages:

Dec 15 18:37:53 proto1 ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x2
Dec 15 18:37:53 proto1 ata2.00: irq_stat 0x40000001
Dec 15 18:37:53 proto1 ata2.00: cmd 35/00:e0:a7:d2:01/00:01:33:00:00/e0
tag 0 cdb 0x0 data 245760 out
Dec 15 18:37:53 proto1 res 51/84:00:86:d4:01/00:00:33:00:00/e0 Emask
0x10 (ATA bus error)
Dec 15 18:37:54 proto1 ata2: soft resetting port
Dec 15 18:37:54 proto1 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
310)
Dec 15 18:37:54 proto1 ata2.00: configured for UDMA/33
Dec 15 18:37:54 proto1 ata2: EH complete
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] 976773168 512-byte hardware
sectors (500108 MB)
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] Write Protect is off
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Dec 15 18:38:15 proto1 ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x2
Dec 15 18:38:15 proto1 ata2.00: irq_stat 0x40000001
Dec 15 18:38:15 proto1 ata2.00: cmd 35/00:80:bf:09:14/00:01:33:00:00/e0
tag 0 cdb 0x0 data 196608 out
Dec 15 18:38:15 proto1 res 51/84:00:3e:0b:14/00:00:33:00:00/e0 Emask
0x10 (ATA bus error)
Dec 15 18:38:15 proto1 ata2: soft resetting port
Dec 15 18:38:15 proto1 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
310)
Dec 15 18:38:15 proto1 ata2.00: configured for UDMA/33
Dec 15 18:38:15 proto1 ata2: EH complete
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] 976773168 512-byte hardware
sectors (500108 MB)
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] Write Protect is off
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] Write cache: enabled, read

cache: enabled, doesn't support DPO or FUA

lspci:
00:00.0 Host bridge: ATI Technologies Inc Unknown device 7910 00:01.0 PCI bridge: ATI Technologies Inc Unknown device 7912 00:07.0 PCI bridge: ATI Technologies Inc Unknown device 7917 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SB600 SMBus (rev 13) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SB600 Azalia
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SB600 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon X1200 Series 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev c0)

Quoted 4 lines

thanks and best regards

zsolt

sorry, kernel version is: 2.6.23-gentoo-r1

#2 lore raw
Quoted 2 lines · On Sat, 15 Dec 2007 21:10:47 +0100 Zsolt Barat <[email protected]> wrote:
Quoted 1 line · Zsolt Barat

hi list,

Let's cc the IDE development list.

Quoted 80 lines
Quoted 74 lines

i just bought a "MyBook" called external HD with a fixed enclosure, from WD. Connected to the SATA port i constantly get "ATA bus error" messages in the kernel log. Is this a known issue?

/var/log/messages:

Dec 15 18:37:53 proto1 ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x2
Dec 15 18:37:53 proto1 ata2.00: irq_stat 0x40000001
Dec 15 18:37:53 proto1 ata2.00: cmd 35/00:e0:a7:d2:01/00:01:33:00:00/e0
tag 0 cdb 0x0 data 245760 out
Dec 15 18:37:53 proto1 res 51/84:00:86:d4:01/00:00:33:00:00/e0 Emask
0x10 (ATA bus error)
Dec 15 18:37:54 proto1 ata2: soft resetting port
Dec 15 18:37:54 proto1 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
310)
Dec 15 18:37:54 proto1 ata2.00: configured for UDMA/33
Dec 15 18:37:54 proto1 ata2: EH complete
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] 976773168 512-byte hardware
sectors (500108 MB)
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] Write Protect is off
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 15 18:37:54 proto1 sd 1:0:0:0: [sdb] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Dec 15 18:38:15 proto1 ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0
action 0x2
Dec 15 18:38:15 proto1 ata2.00: irq_stat 0x40000001
Dec 15 18:38:15 proto1 ata2.00: cmd 35/00:80:bf:09:14/00:01:33:00:00/e0
tag 0 cdb 0x0 data 196608 out
Dec 15 18:38:15 proto1 res 51/84:00:3e:0b:14/00:00:33:00:00/e0 Emask
0x10 (ATA bus error)
Dec 15 18:38:15 proto1 ata2: soft resetting port
Dec 15 18:38:15 proto1 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
310)
Dec 15 18:38:15 proto1 ata2.00: configured for UDMA/33
Dec 15 18:38:15 proto1 ata2: EH complete
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] 976773168 512-byte hardware
sectors (500108 MB)
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] Write Protect is off
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Dec 15 18:38:15 proto1 sd 1:0:0:0: [sdb] Write cache: enabled, read

cache: enabled, doesn't support DPO or FUA

lspci:
00:00.0 Host bridge: ATI Technologies Inc Unknown device 7910 00:01.0 PCI bridge: ATI Technologies Inc Unknown device 7912 00:07.0 PCI bridge: ATI Technologies Inc Unknown device 7917 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SB600 SMBus (rev 13) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SB600 Azalia
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SB600 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon X1200 Series 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev c0)

Quoted 4 lines

thanks and best regards

zsolt

sorry, kernel version is: 2.6.23-gentoo-r1

#3 lore raw
Quoted 11 lines · Andrew Morton
Quoted 2 lines · On Sat, 15 Dec 2007 21:10:47 +0100 Zsolt Barat <[email protected]> wrote:
Quoted 1 line · Zsolt Barat

hi list,

Let's cc the IDE development list.

Quoted 4 lines
Quoted 4 lines

i just bought a "MyBook" called external HD with a fixed enclosure, from WD. Connected to the SATA port i constantly get "ATA bus error" messages in the kernel log. Is this a known issue?

As an FYI: I've had a lot of problems with the big prepackaged drives in the last 6 months even from Windows, so I would not be too quick to blame Linux.

ie.
I bought several 500GB / 1000GB Buffalo Drives last month with plans to use them from Windows via USB.

I attempted to do a lot of heavy file copying to/from them. I was getting a bunch of "Delayed Write Failures",

I finally gave up.

The 500GB drives had a single hard drive internally, so I opened the case, removed the drive and connected them via standalone external carriers I had around. In that mode the drives worked fine (from Windows). I've used both standalone eSata external carriers and standalone USB external carriers with these same physical drives with no issues.

My conclusion is that the electronics in the prepackaged external units is just not up to the job if your doing heavy i/o.

Greg

Signature · 9 lines
Greg Freemyer
Litigation Triage Solutions Specialist
http://www.linkedin.com/in/gregfreemyer
First 99 Days Litigation White Paper -
http://www.norcrossgroup.com/forms/whitepapers/99%20Days%20whitepaper.pdf

The Norcross Group
The Intersection of Evidence & Technology
http://www.norcrossgroup.com
#4 lore raw

Greg Freemyer schreef:

Quoted 38 lines · Andrew Morton
Quoted 16 lines · On Sat, 15 Dec 2007 21:10:47 +0100 Zsolt Barat <[email protected]> wrote:
Quoted 6 lines
Quoted 2 lines · Zsolt Barat

hi list,

Let's cc the IDE development list.

Quoted 5 lines
Quoted 5 lines

i just bought a "MyBook" called external HD with a fixed enclosure, from WD. Connected to the SATA port i constantly get "ATA bus error" messages in the kernel log. Is this a known issue?

As an FYI: I've had a lot of problems with the big prepackaged drives in the last 6 months even from Windows, so I would not be too quick to blame Linux.

ie.
I bought several 500GB / 1000GB Buffalo Drives last month with plans to use them from Windows via USB.

I attempted to do a lot of heavy file copying to/from them. I was getting a bunch of "Delayed Write Failures",

I finally gave up.

The 500GB drives had a single hard drive internally, so I opened the case, removed the drive and connected them via standalone external carriers I had around. In that mode the drives worked fine (from Windows). I've used both standalone eSata external carriers and standalone USB external carriers with these same physical drives with no issues.

Quoted 5 lines

My conclusion is that the electronics in the prepackaged external units is just not up to the job if your doing heavy i/o.

Greg

Could u check the temps of the disk ? I had that error in windows also with to hot disks ! If temp is >50°C I would start to worry :) --
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#5 lore raw
In reply to Greg Freemyer
Quoted 38 lines · Greg Freemyer
Quoted 15 lines · Andrew Morton
Quoted 4 lines · On Sat, 15 Dec 2007 21:10:47 +0100 Zsolt Barat <[email protected]> wrote:
Quoted 2 lines · Zsolt Barat

hi list,

Let's cc the IDE development list.

Quoted 5 lines
Quoted 5 lines

i just bought a "MyBook" called external HD with a fixed enclosure, from WD. Connected to the SATA port i constantly get "ATA bus error" messages in the kernel log. Is this a known issue?

As an FYI: I've had a lot of problems with the big prepackaged drives in the last 6 months even from Windows, so I would not be too quick to blame Linux.

ie.
I bought several 500GB / 1000GB Buffalo Drives last month with plans to use them from Windows via USB.

I attempted to do a lot of heavy file copying to/from them. I was getting a bunch of "Delayed Write Failures",

I finally gave up.

The 500GB drives had a single hard drive internally, so I opened the case, removed the drive and connected them via standalone external carriers I had around. In that mode the drives worked fine (from Windows). I've used both standalone eSata external carriers and standalone USB external carriers with these same physical drives with no issues.

Quoted 4 lines

My conclusion is that the electronics in the prepackaged external units is just not up to the job if your doing heavy i/o.

thanks for your answer. the error messages are vanished for now. i switched on/of the power supply for the hd-box sometimes and then it suddenly worked normaly. it even negotiates with 3 Gbps and UDMA/133.

Dec 18 13:05:50 proto1 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl
300)
Dec 18 13:05:50 proto1 ata2.00: ATA-6: WD      My Book ES, 012, max

UDMA/133

maybe it is the cable, i have to investigate it. it also claimes to have an automatic power on/off function, whatever this should mean.

best regards

zsolt

A message that is not in the archive (sent off-list or not yet received): [email protected]

#7 lore raw
Quoted 39 lines · Jean-Louis Dupond

Greg Freemyer schreef:

Quoted 38 lines · Andrew Morton
Quoted 16 lines · On Sat, 15 Dec 2007 21:10:47 +0100 Zsolt Barat <[email protected]> wrote:
Quoted 6 lines
Quoted 2 lines · Zsolt Barat

hi list,

Let's cc the IDE development list.

Quoted 5 lines
Quoted 5 lines

i just bought a "MyBook" called external HD with a fixed enclosure, from WD. Connected to the SATA port i constantly get "ATA bus error" messages in the kernel log. Is this a known issue?

As an FYI: I've had a lot of problems with the big prepackaged drives in the last 6 months even from Windows, so I would not be too quick to blame Linux.

ie.
I bought several 500GB / 1000GB Buffalo Drives last month with plans to use them from Windows via USB.

I attempted to do a lot of heavy file copying to/from them. I was getting a bunch of "Delayed Write Failures",

I finally gave up.

The 500GB drives had a single hard drive internally, so I opened the case, removed the drive and connected them via standalone external carriers I had around. In that mode the drives worked fine (from Windows). I've used both standalone eSata external carriers and standalone USB external carriers with these same physical drives with no issues.

Quoted 8 lines
Quoted 5 lines

My conclusion is that the electronics in the prepackaged external units is just not up to the job if your doing heavy i/o.

Greg

Could u check the temps of the disk ? I had that error in windows also with to hot disks ! If temp is >50°C I would start to worry :)

hi,
thanks for your answer. i can't check the temps via software tools, but i doubt it's the temperature, since it seems to have a fan inbuilt into the case.

best regards

zsolt

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/