Something is consuming power after shutdown
<http://bugzilla.kernel.org/show_bug.cgi?id=10797>
<http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=481493>
After poweroff, something still working and consuming power. So I loss ~4% of my battery charge in each 12h.
If I shutdown my laptop using Kernel 2.6.24/25 when battery is 100%, after 12h my battery charge go to 96% (this information is checked with kpowersave and with LED available in my laptop that change color from blue to yellow when battery is not FULL).
If I shutdown this same laptop by WinXP (I have a dual boot), nothing change. So, my battery still have 100% after 12h (or more).
I see a similar problem in EeePC (the problem is with snd_hda_intel driver), but I don't have this driver loaded:
http://wiki.debian.org/DebianEeePC/HowTo/Troubleshooting#head-84d9d8a97c9ce198c59edd9cd93a05ab24fd1ff8
Best regards,
Renato S. Yamane
Quoted 11 lines · On Mon, 26 May 2008 09:59:47 -0300 "Renato S. Yamane"…
<http://bugzilla.kernel.org/show_bug.cgi?id=10797>
<http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=481493>After poweroff, something still working and consuming power. So I loss ~4% of my battery charge in each 12h.
If I shutdown my laptop using Kernel 2.6.24/25 when battery is 100%, after 12h my battery charge go to 96% (this information is checked with kpowersave and with LED available in my laptop that change color from blue to yellow when battery is not FULL).
Quoted 5 lines
If I shutdown this same laptop by WinXP (I have a dual boot), nothing change. So, my battery still have 100% after 12h (or more).
I see a similar problem in EeePC (the problem is with
snd_hda_inteldriver), but I don't have this driver loaded:
the most obvious cause could be Wake-on-Lan, that leaves a part of the system active (specifically, the network card). With the "ethtool" program you can queary and set the state of this.
Similarly, but less likely, there is wake-on-serial and wake-on-usb, in theory those are possible too but I've yet to see one of those on any of my machines.
Quoted 10 lines · Arjan van de Ven
Quoted 5 lines · Renato S. Yamane
<http://bugzilla.kernel.org/show_bug.cgi?id=10797>
<http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=481493>After poweroff, something still working and consuming power. So I loss ~4% of my battery charge in each 12h.
the most obvious cause could be Wake-on-Lan, that leaves a part of the system active (specifically, the network card). With the "ethtool" program you can queary and set the state of this.
My network card have option WOL "disabled"
# ethtool eth0 | grep Wake
Supports Wake-on: pg
Wake-on: dQuoted 3 lines
Similarly, but less likely, there is wake-on-serial and wake-on-usb, in theory those are possible too but I've yet to see one of those on any of my machines.
My laptop don't have serial port and wake-on-usb is disabled too:
# cat /proc/acpi/wakeup Device S-state Status Sysfs node LID0 S4 *enabled RP01 S4 disabled pci:0000:00:1c.0 RP02 S4 disabled pci:0000:00:1c.1 RP03 S4 disabled RP04 S4 disabled USB1 S0 disabled pci:0000:00:1d.0 USB2 S0 disabled pci:0000:00:1d.1 USB3 S0 disabled pci:0000:00:1d.2 USB4 S0 disabled pci:0000:00:1d.3 USB7 S0 disabled pci:0000:00:1d.7 MODM S4 disabled pci:0000:00:1e.3 PS2K S4 disabled pnp:00:07
Best regards,
Renato S. Yamane
Re: [CRM114spam]: [Bug 10797] Something is consuming power after shutdown
In reply to Renato S. YamaneQuoted 2 lines · * Renato S. Yamane ([email protected]) wrote:
<http://bugzilla.kernel.org/show_bug.cgi?id=10797>
<http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=481493>
Also add a Ubuntu equivalent which is:
https://bugs.launchpad.net/ubuntu/+bug/110784
(In my case a Tosh Equium A100-306 )
Quoted 7 lines
After poweroff, something still working and consuming power. So I loss ~4% of my battery charge in each 12h.
If I shutdown my laptop using Kernel 2.6.24/25 when battery is 100%, after 12h my battery charge go to 96% (this information is checked with kpowersave and with LED available in my laptop that change color from blue to yellow when battery is not FULL).
I haven't got the actual numbers, but I'd say mine is a little more - may be 10% from memory overnight. Certainly between a Sunday evening and a Saturday afternoon there is nothing left for it to turn back on.
Following the thread I did notice I had w-o-l enabled; I've disabled it - see if it makes any difference tonight.
Dave
Signature · 4 lines
-----Open up your eyes, open up your mind, open up your code ------- / Dr. David Alan Gilbert | Running GNU/Linux on Alpha,68K| Happy \ \ gro.gilbert @ treblig.org | MIPS,x86,ARM,SPARC,PPC & HPPA | In Hex / \ _________________________|_____ http://www.treblig.org |_______/
Quoted 19 lines · Renato S. Yamane
Quoted 7 lines · Arjan van de Ven
Quoted 2 lines · Renato S. Yamane
After poweroff, something still working and consuming power. So I loss ~4% of my battery charge in each 12h.
the most obvious cause could be Wake-on-Lan, that leaves a part of the system active (specifically, the network card). With the "ethtool" program you can queary and set the state of this.
My network card have option WOL "disabled"
# ethtool eth0 | grep Wake Supports Wake-on: pg Wake-on: dQuoted 3 lines
Similarly, but less likely, there is wake-on-serial and wake-on-usb, in theory those are possible too but I've yet to see one of those on any of my machines.
Quoted 14 lines
# cat /proc/acpi/wakeup Device S-state Status Sysfs node LID0 S4 *enabled RP01 S4 disabled pci:0000:00:1c.0 RP02 S4 disabled pci:0000:00:1c.1 RP03 S4 disabled RP04 S4 disabled USB1 S0 disabled pci:0000:00:1d.0 USB2 S0 disabled pci:0000:00:1d.1 USB3 S0 disabled pci:0000:00:1d.2 USB4 S0 disabled pci:0000:00:1d.3 USB7 S0 disabled pci:0000:00:1d.7 MODM S4 disabled pci:0000:00:1e.3 PS2K S4 disabled pnp:00:07
I test two times as commented in [1] and I can see that this problem don't hapen if, before shutdown, I close LCD Display (activing LID to hibernate).
[1] <http://bugzilla.kernel.org/show_bug.cgi?id=10797#c1>
So, to shutdown laptop with no battery change, is necessary:
1) Active LID (closing LCD Display). With this, my laptop will hibernate, so is necessary wake-up again.
2) Shutdown
Best regards,
Renato S. Yamane
Hi!
Quoted 12 lines
<http://bugzilla.kernel.org/show_bug.cgi?id=10797>
<http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=481493>After poweroff, something still working and consuming power. So I loss ~4% of my battery charge in each 12h.
If I shutdown my laptop using Kernel 2.6.24/25 when battery is 100%, after 12h my battery charge go to 96% (this information is checked with kpowersave and with LED available in my laptop that change color from blue to yellow when battery is not FULL).
Quoted 3 lines
If I shutdown this same laptop by WinXP (I have a dual boot), nothing change. So, my battery still have 100% after 12h (or more).
Try to find out which component eats power, eg. by opening the machine searching for heat.
(And yes, your hw is broken; on pc it is traditionaly hw responsibility to power machine down.)
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
Quoted 10 lines · Pavel Machek
Renato S. Yamane wrote:
...Quoted 2 lines
<http://bugzilla.kernel.org/show_bug.cgi?id=10797>
<http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=481493>Try to find out which component eats power, eg. by opening the machine searching for heat.
(And yes, your hw is broken; on pc it is traditionaly hw responsibility to power machine down.)
OK, I try do this but I think this is very difficult because demand power is very low and is not enought to do hot some component. But I will try.
I don't think that my hardware is broked because I don't have this kind of problem on Kernel <=2.6.22 or in other OS.
And other user have the same problem (cc'ed on Bug #10797)
Best regards,
Renato S. Yamane
Quoted 2 lines · Pavel Machek
(And yes, your hw is broken; on pc it is traditionaly hw responsibility to power machine down.)
Something changed in the laptop vendor's minds about this since Vista. Very new ThinkPads also had this problem (I am not sure it has been fixed already or not).
We may have to start shutting down every device and bus on our way out for lunch when told to go into S5, now. Time will tell.
Signature · 4 lines
"One disk to rule them all, One disk to find them. One disk to bring them all and in the darkness grind them. In the Land of Redmond where the shadows lie." -- The Silicon Valley Tarot Henrique Holschuh
Hi!
Quoted 9 lines
Quoted 2 lines
(And yes, your hw is broken; on pc it is traditionaly hw responsibility to power machine down.)
OK, I try do this but I think this is very difficult because demand power is very low and is not enought to do hot some component. But I will try.
I don't think that my hardware is broked because I don't have this kind of problem on Kernel <=2.6.22 or in other OS.
Can you try to find out when that started happening?
does it still happen with acpi=off ?
does it each too much power if you use 4second hold of power button to shut it down from running linux?
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
Quoted 9 lines · Pavel Machek
Quoted 8 lines · Renato S. Yamane
Quoted 2 lines · Pavel Machek
(And yes, your hw is broken; on pc it is traditionaly hw responsibility to power machine down.)
OK, I try do this but I think this is very difficult because demand power is very low and is not enought to do hot some component. But I will try.
Quoted 8 lines
Quoted 3 lines
I don't think that my hardware is broked because I don't have this kind of problem on Kernel <=2.6.22 or in other OS.
Track: <http://bugzilla.kernel.org/show_bug.cgi?id=10797>Can you try to find out when that started happening?
does it still happen with acpi=off?
does it each too much power if you use 4second hold of power button to shut it down from running linux?
With acpi=off this problem don't happening, but a lot of other problem happening (as fan control).
I will try halt my laptop holding power button today and report you tomorrow.
Best regards,
Renato S. Yamane
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 17 lines · Renato S. Yamane
Quoted 8 lines · Pavel Machek
Quoted 7 lines · Renato S. Yamane
Quoted 2 lines · Pavel Machek
(And yes, your hw is broken; on pc it is traditionaly hw responsibility to power machine down.)
OK, I try do this but I think this is very difficult because demand power is very low and is not enought to do hot some component. But I will try.
Quoted 7 lines
Quoted 3 lines
I don't think that my hardware is broked because I don't have this kind of problem on Kernel <=2.6.22 or in other OS.
Track: <http://bugzilla.kernel.org/show_bug.cgi?id=10797>Can you try to find out when that started happening?
does it still happen with acpi=off?
does it each too much power if you use 4second hold of power button to shut it down from running linux?
Quoted 5 lines
With acpi=off this problem don't happening, but a lot of other problem happening (as fan control).
I will try halt my laptop holding power button today and report you tomorrow.
If I hold power button to force shutdown I don't have this problem with battery charge.
Best regards,
Renato S. Yamane
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.6 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iD8DBQFITRDdrf2L358fCLsRAuKUAJ9N2HVzuFnOA5zDes286/F8LgPfNgCePS4Z YMWoFzYl+eF3/do1Je9oly8=
=31/g
-----END PGP SIGNATURE-----
Quoted 21 lines · Renato S. Yamane
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Quoted 17 lines · Renato S. Yamane
Quoted 15 lines · Pavel Machek
Quoted 10 lines · Renato S. Yamane
Quoted 2 lines · Pavel Machek
(And yes, your hw is broken; on pc it is traditionaly hw responsibility to power machine down.)
OK, I try do this but I think this is very difficult because demand power is very low and is not enought to do hot some component. But I will try.
I don't think that my hardware is broked because I don't have this kind of problem on Kernel <=2.6.22 or in other OS.
Track: <http://bugzilla.kernel.org/show_bug.cgi?id=10797>Can you try to find out when that started happening?
does it still happen with acpi=off?
does it each too much power if you use 4second hold of power button to shut it down from running linux?
Quoted 8 lines
Quoted 5 lines
With acpi=off this problem don't happening, but a lot of other problem happening (as fan control).
I will try halt my laptop holding power button today and report you tomorrow.
If I hold power button to force shutdown I don't have this problem with battery charge.
Too bad, I can't call the hw terminally broken, then.
If you boot into init=/bin/bash (minimum drivers) will it still consume too much power after sysrq-o?
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
Quoted 4 lines · Pavel Machek
Quoted 2 lines
If I hold power button to force shutdown I don't have this problem with battery charge.
Too bad, I can't call the hw terminally broken, then.
No, just the ACPI firmware :-)
Signature · 4 lines
"One disk to rule them all, One disk to find them. One disk to bring them all and in the darkness grind them. In the Land of Redmond where the shadows lie." -- The Silicon Valley Tarot Henrique Holschuh
Quoted 7 lines · Pavel Machek
Quoted 6 lines · Renato S. Yamane
Quoted 1 line · Pavel Machek
does it still happen with acpi=off?
With acpi=off this problem don't happening, but a lot of other problem happening (as fan control).
Quoted 7 lines
Quoted 2 lines
If I hold power button to force shutdown I don't have this problem with battery charge.
Too bad, I can't call the hw terminally broken, then.
If you boot into init=/bin/bash (minimum drivers) will it still consume too much power after sysrq-o?
I hold power button to force shutdown and start with init=/bin/bash, but this problem still exist :-(
You know about this?:
<http://linux.toshiba-dme.co.jp/linux/eng/develop.htm>
Best regards,
Renato S. Yamane